PRODUCT BRIEF 10 Gigabit/s Ethernet Transceiver with OC-192c Framer and XAUI Interface The TenGiPHY-W is a single chip transceiver IC for 10 Gbit/s Ethernet and Fibre Channel connectivity. It offers a serial, full duplex 10 Gbit/s interface to an optical sub-module. The integrated CDR and CMU operate at data rates between 9.95328 and 10.51875Gbit/s. The TenGiPHY-W provides the XGXS, PCS and PMA sublayers of the 10G Ethernet and Fibre Channel standards. For WAN applications a standard OC-192/STM-64 SONET/SDH framer together with flexible clocking modes enables a direct connection to the public network without additional components. The networking system can control the chip via a narrow-width MDIO interface by writing and reading its control and status registers. Applications ■ ■ ■ ■ Fiber optic modules according to the XENPAK multi-source agreement 10 Gbit/s Ethernet and Fibre Channel line cards Ethernet backbones in Metro Area Networks Terabit Routers Features ■ ■ ■ ■ ■ ■ Complete 10 Gbit/s Ethernet and Fibre Channel PHY supporting WAN and LAN applications Complies with IEEE 802.3ae Compliant to XENPAK multisource agreement Complies with ANSI 1413-D Embedded µController allows for control and tuning of the PMDs via analog interfaces Clock & data recovery and clock multiplying unit without external loop filter components ■ ■ ■ ■ ■ ■ ■ UPF 01002 Complies with jitter tolerance and jitter transmit requirements according to Telcordia GR-1244CORE and ITU-T G.825 Supports various clocking modes based on external reference clocks, loop- and external timing Integrated bit error rate tester (BERT) usable for multiple atspeed diagnostic scenarios Includes the XGXS, PCS, WIS, and PMA sublayers of the OSI protocol stack Synchronization and de-skewing of XAUI lanes Integrated standard STS-192/ STM-64 SONET/SDH framer according to GR-253-CORE, ANSI T1. 105/416, ITU-T G.707. Optionally maps/extracts 10 Gbit/s Ethernet packets into/ from the STS-192c/VC4-64c payload or conveys them to the serial interface directly ■ ■ ■ ■ Performance monitoring according to ANSI T1. 231 Various loop back modes for system debugging Provides access to E²PROM via I²C interface according to XENPAK requirements; automatic E²PROM download on power-up Power-efficient design: <1.3W @ 1.3V Interfaces ■ ■ ■ ■ ■ ■ Full duplex, XFI compliant serial CML line interface for data rates between 9.95 and 10.5 Gbit/s Quad serial Gbit/s XAUI interface with data rates between 3.1 and 3.2 Gbit/s MDIO interface I²C bus interface XENPAK diagnostic interface providing eight 12-bit ADCs and four 10-bit DACs IEEE 1149.1 JTAG boundary scan interface UPF 01002 TenGiPHY-W N e v e r s t o p t h i n k i n g . PRODUCT BRIEF Block Diagram 8B/10B 8B/10B CODEC CODEC 64B/66B 64B/66B CODEC CODEC Scrambler Scrambler Clock Clock Multiplier Multiplier Unit Unit Clock Clock&& Data Data Recovery Recovery Serial Line 1010 GG Serial Line Interface Interface Gbit/s BERT BERT Framer Framer 4x 3.125 Sync Sync&& Deskew Deskew STS-192c/ /STM64 STM64 STS-192c XAUI Interface System Interface JTAG JTAGInterface Interface Line Interface 9.95328 / 10.3125 Gbit/s µController µController I²C I²C Interface Interface XENPAK XENPAK Diagnostic Diagnostic Documentation and Support Package ■ Data Sheet ■ Hardware Evaluation System includes mother- and transponder board MDIO/MDC MDIO/MDC Interface Interface ■ ■ Alarm Alarm Interface Interface WINEASY Software for MS Windows with graphical user interface Application Assistant: Configuration Software for MS Windows for device initialization Type Sales Code Package TenGiPHY-W UPF 01002 P-FCHBGA-177-1 Application Example UPF 01002 Laser Management Interface CMU Data LDD 10Gbps CDR PCS / WIS MAC XGXS Clock LA TIA Photodiode E²PROM I²C Interface Transponder Module 10G Ethernet Line Card How to reach us: http://www.infineon.com Published by Infineon Technologies AG, Bereich Kommunikation, St.-Martin-Strasse 53, D-81541 München © Infineon Technologies AG 2002. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide. Published by Infineon Technologies AG Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in lifesupport devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Printed in Germany PS 0502.2