SSL1623PH SMPS ICs for mains LED drivers Rev. 01 — 15 September 2008 Product data sheet 1. General description The SSL1623PH is a Switched Mode Power Supply (SMPS) controller IC that operates directly from the rectified universal mains. It is implemented in the high voltage EZ-HV SOI (Easy High Voltage Silicon-On-Insulator) process, combined with a low voltage BiCMOS (Bipolar Complementary Metal Oxide Semiconductor) process. The device includes a high voltage power switch and a circuit for start-up directly from the rectified mains voltage. A dedicated circuit for valley switching is built in, which makes a very efficient slim-line electronic LED driver concept possible. The SSL1623PH can operate in LED applications with a power range of up to 25 W. The SSL152x family would be a better choice if power below 15 W is required. In its most basic version of application the SSL1623PH acts as a voltage source. Here no additional secondary electronics are required. A combined voltage and current source can be realized with minimum costs for external components. Implementation of the SSL1623PH renders an efficient and low cost LED power supply system. 2. Features n n n n n n n n n n n n Integrated power switch: 6.5 Ω and 650 V Operates from universal AC mains supplies, 80 V to 276 V Adjustable frequency for flexible design RC oscillator for load insensitive regulation loop constant Valley switching for minimum switch-on loss Adjustable overcurrent protection Undervoltage protection Temperature protection Short circuit winding protection Safe restart mode for system fault conditions Simple application with both primary and secondary (opto) feedback Available in 16-pin DIP package 3. Applications n n n n n LED ballasts Contour lighting LED spotlights Channel letter lighting Down lighting SSL1623PH NXP Semiconductors n Commercial lighting (e.g. retail displays) 4. Quick reference data Table 1. Symbol Quick reference data Parameter Conditions Min Typ Max Unit −0.4 - +40 V -0.4 - +650 V - 0.5 - mA Tj = 25 °C - 6.5 7.5 Ω Tj = 100 °C - 9.0 10.0 Ω VCC supply voltage continuous VDRAIN voltage on pin DRAIN IDRAIN current on pin DRAIN no auxiliary supply RDSon drain-source on-state resistance Isource = −0.5 A [1] fosc oscillator frequency 10 - 200 kHz Tamb ambient temperature −20 - +85 °C [1] Pins VCC and RC are not allowed to be current driven. 5. Ordering information Table 2. Ordering information Type number SSL1623PH Package Name Description Version DIP16 plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 2 of 15 SSL1623PH NXP Semiconductors 6. Block diagram VCC 3 14 SUPPLY 1, 2, 7, 9, 10, 13, 15, 16 VALLEY SSL1623PH GND DRAIN n.c. LOGIC 4 100 mV stop RC 5 OSCILLATOR THERMAL SHUTDOWN PROTECTION LOGIC low freq f 12 POWER-UP RESET 1.8 SOURCE blank U overcurrent 6 2.5 V 10× 0.5 V 11 REG AUX short winding SGND 8 0.75 V 014aaa566 Fig 1. Block diagram of SSL1623PH SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 3 of 15 SSL1623PH NXP Semiconductors 7. Pinning information 7.1 Pinning n.c. 1 16 n.c. n.c. 2 15 n.c. VCC 3 14 DRAIN GND 4 13 n.c. SSL1623PH RC 5 12 SOURCE REG 6 11 AUX n.c. 7 10 n.c. SGND 8 9 n.c. 014aaa345 Fig 2. Pin configuration 7.2 Pin description Table 3. Pin description Symbol Pin Description VCC 3 supply voltage GND 4 ground RC 5 frequency setting REG 6 regulation input SGND 8 signal ground; must preferably be connected to pin GND AUX 11 input for voltage from auxiliary winding for timing (demagnetization) SOURCE 12 source of internal MOS switch n.c. 1, 2, 7, 9, 10, 13, 15, 16. not connected DRAIN 14 drain of internal MOS switch; input for start-up current and valley sensing 8. Functional description The SSL1623PH is the heart of a compact flyback converter, with the IC placed at the primary side. The auxiliary winding of the transformer can be used for indirect feedback to control the isolated output. This additional winding also powers the IC. A more accurate control of the output voltage and/or current can be implemented with an additional secondary sensing circuit and opto coupler feedback. The SSL1623PH can be used in a constant power mode or in a constant current mode to drive LEDs. The SSL1623PH uses voltage mode control. The frequency is determined by the maximum transformer demagnetizing time and the time of the oscillator. In the first case, the converter operates in the Self Oscillating Power Supply (SOPS) mode. In the latter SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 4 of 15 SSL1623PH NXP Semiconductors case, it operates at a constant frequency, which can be adjusted with external components RRC and CRC. Furthermore, a primary stroke is started only in a valley of the secondary ringing. This valley switching principle minimizes capacitive switch-on losses. 8.1 Start-up and undervoltage lockout Initially, the IC is self-supplying from the rectified mains voltage. The IC starts switching as soon as the voltage on pin VCC passes the VCC(startup) level. The supply is taken over by the auxiliary winding of the transformer as soon as VCC is high enough and the supply from the line is stopped for high efficiency operation. As soon as the voltage on pin VCC drops below the VCC(stop) level, the IC stops switching and restarts from the rectified mains voltage. 8.2 Oscillator The frequency of the oscillator is set by the external resistor and capacitor on pin RC. The external capacitor is charged rapidly to the VRC(max) level and, starting from a new primary stroke, it discharges to the VRC(min) level. Because the discharge is exponential, the relative sensitivity of the duty factor to the regulation voltage at low duty factor is almost equal to the sensitivity at high duty factors. This results in a more constant gain over the duty factor range compared to systems with a linear sawtooth oscillator. Stable operation at low duty factors is easily realized. For high efficiency, the frequency is reduced as soon as the duty factor drops below a certain value. This is accomplished by increasing the oscillator charge time. To ensure that the capacitor can be charged within the charge time, the value of the oscillator capacitor should be limited to approximately 1 nF. 8.3 Duty factor control The duty factor is controlled by the internal regulation voltage and the oscillator signal on pin RC. The internal regulation voltage is equal to the external regulation voltage (minus 2.5 V) multiplied by the gain of the error amplifier (typical 20 dB). The minimum duty factor of the switched mode power supply is 0 %. The maximum duty factor is set to 75 % (typical value at 100 kHz oscillation frequency). 8.4 Valley switching A new cycle is started at the primary stroke when the switch is switched on (see Figure 3). After a certain time (determined by the RC oscillator voltage and the internal regulation level), the switch is turned off and the secondary stroke starts. The internal regulation level is determined by the voltage on pin REG. After the secondary stroke, the DRAIN voltage shows an oscillation with a frequency of approximately, see Equation 1. 1 -----------------------------2π × L p C p (1) Where: Lp is the primary self-inductance on the drain node. Cp is the parasitic capacitance on the drain node. SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 5 of 15 SSL1623PH NXP Semiconductors As soon as the oscillator voltage is high again and the secondary stroke has ended, the circuit waits for a low drain voltage before starting a new primary stroke. The primary stroke starts some time before the actual valley at low ringing frequencies, and some time after the actual valley at high ringing frequencies. Figure 4 shows a typical curve for a reflected voltage N × Vo of 80 V. This voltage is the output voltage Vo (see Figure 5) transferred to the primary side of the transformer with the factor N (determined by the turns ratio of the transformer). Figure 4 shows that the system switches exactly at minimum drain voltage for ringing frequencies of 480 kHz, thus reducing the switch-on losses to a minimum. At 200 kHz, the next primary stroke is started at 33 ° before the valley. The switch-on losses are still reduced significantly. primary stroke secondary stroke secondary ringing drain valley secondary stroke A RC oscillator regulation level B col007 A: Start of new cycle with valley switching. B: Start of new cycle in a classical system. Fig 3. Signals for valley switching SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 6 of 15 SSL1623PH NXP Semiconductors 001aaa311 40 phase (°) 20 0 −20 −40 0 200 400 600 800 f (kHz) Reflected voltage at N × Vo = 80 V. Fig 4. Typical phase of drain ringing at switch-on 8.5 Demagnetization The system operates in discontinuous conduction mode all the time. As long as the secondary stroke has not ended, the oscillator will not start a new primary stroke. During the suppression time tsup(xfmr_ring), demagnetization recognition is suppressed. This suppression may be necessary in applications where the transformer has a large leakage inductance and at low output voltages. 8.6 Protections 8.6.1 Overcurrent protection The cycle-by-cycle peak drain current limit circuit uses the external source resistor RI (see Figure 5) to measure the current. The circuit is activated after the leading edge blanking time tleb. The protection circuit limits the source voltage to VSOURCE(max) and thus limits the primary peak current. 8.6.2 Short winding protection The short winding protection circuit is also activated after the leading edge blanking time. If the source voltage exceeds the short winding protection voltage Vswp, the SSL1623PH stops switching. Only a power-on reset will restart normal operation. The short winding protection also protects in case of a secondary diode short circuit. 8.6.3 Overtemperature protection An accurate temperature protection is provided in the SSL1623PH. When the junction temperature exceeds the thermal shutdown temperature, the IC stops switching. During thermal protection the IC current is lowered to the start-up current. The IC continues normal operation as soon as the overtemperature situation has disappeared. SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 7 of 15 SSL1623PH NXP Semiconductors 8.6.4 Overvoltage protection Overvoltage protection can be achieved in the application by pulling pin REG above its normal operation level or by keeping the level of pin AUX above Vdet(demag). The current primary stroke is terminated immediately and no new primary stroke is started until the voltage on pin REG drops to its normal operation level. Pin REG has an internal clamp. The current feed into pin REG must be limited. 8.7 Characteristics of the complete LED power supply 8.7.1 Input The input voltage range comprises the universal AC mains from 80 V to 276 V. 8.7.2 Accuracy The accuracy of the complete converter, functioning as a voltage source with primary sensing, is approximately 8 % (mainly dependent on the transformer coupling). The accuracy with secondary sensing is defined by the accuracy of the external components. For safety requirements in case of opto coupler feedback loss, the primary sensing remains active when an overvoltage circuit is connected. 8.7.3 Efficiency An efficiency of over 80 % at maximum output power can be achieved for a complete converter designed for universal mains. 8.7.4 Ripple A minimum ripple is obtained in a system designed for a maximum duty factor of 50 % under normal operating conditions and a minimized dead time. The magnitude of the ripple in the output voltage is determined by the frequency and duty factor of the converter, the output current level, and the value and ESR of the output capacitor. 9. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions supply voltage continuous Min Max Unit [1] −0.4 +40 V [1] −0.4 +3 V Voltages VCC VRC voltage on pin RC VSOURCE voltage on pin source −0.4 +5 V VDRAIN voltage on pin DRAIN −0.4 +650 V Currents current on pin REG [2] - 6 mA IAUX current on pin AUX [2] −10 +5 mA IREG Ich charge current −3 - mA Isource source current −2 +2 A IDRAIN current on pin DRAIN −2 +2 A oscillator capacitor SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 8 of 15 SSL1623PH NXP Semiconductors Table 4. Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit Ptot total power dissipation Tamb < 50 °C - 1.7 W Tstg storage temperature −55 +150 °C Tamb ambient temperature −20 +85 °C Tj junction temperature −20 +145 °C pin DRAIN −1500 +1500 V all other pins −2000 +2000 V −200 +200 V General Vesd electrostatic discharge voltage human body model [3] [4] machine model all pins [1] Pins VCC and RC are not allowed to be current driven. [2] Pins REG and AUX are not allowed to be voltage driven. [3] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor. [4] Machine model: equivalent to discharging a 200 pF capacitor through a 0.75 µH coil and a 10 Ω series resistor. 10. Thermal characteristics Table 5. Thermal characteristics Symbol Parameter Rth(j-a) [1] Conditions thermal resistance from junction to ambient [1] in free air Typ Unit 55 K/W Thermal resistance Rth(j-a) can be lower when pin GND is connected to sufficient copper area on the printed-circuit board. 11. Characteristics Table 6. Characteristics Measurement valid data Tamb = 25 °C; no overtemperature; all voltages are measured with respect to ground; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 9 9.5 10 V 7.0 7.5 8.0 V Supplies Supply on pin VCC VCC(startup) start-up supply voltage VCC(stop) stop supply voltage undervoltage lockout ICC(oper) operating supply current normal operation - 1.3 1.9 mA ICC(startup) start-up supply current start-up - 180 400 µA Ich charge current VDRAIN > 60 V VCC = 0 V −650 −520 −390 µA VCC = 8.5 V −375 −275 −175 µA SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 9 of 15 SSL1623PH NXP Semiconductors Table 6. Characteristics …continued Measurement valid data Tamb = 25 °C; no overtemperature; all voltages are measured with respect to ground; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Supply on pin DRAIN IDRAIN current on pin DRAIN no auxiliary supply - 0.5 - mA with auxiliary supply; VDRAIN > 60 V - 30 125 µA - 0 - % - 75 - % Pulse width modulator mode δmin minimum duty factor δmax maximum duty cycle fosc = 100 kHz Self oscillating power supply mode Vdet(demag) demagnetization detection voltage 50 100 150 mV tsup(xfmr_ring) transformer ringing suppression time 1.0 1.5 2.0 µs Oscillator: pin RC VRC(min) minimum voltage on pin RC 60 75 90 mV VRC(max) maximum voltage on pin RC 2.4 2.5 2.6 V tch charging time - 1 - µs fosc oscillator frequency 10 - 200 kHz 2.4 2.5 2.6 V Duty factor regulator: pin REG VREG voltage on pin REG Gv voltage gain Vclamp(REG) clamp voltage on pin REG IREG = 6 mA - 20 - dB - - 7.5 V −102 - +102 V/µs 200 550 800 kHz - 150 - ns Valley switching recognition (∆V/∆t)vrec valley recognition voltage change with time fring ringing frequency td(vrec-swon) valley recognition to switch-on delay time N × Vo = 100 V Output stage (FET) IL(DRAIN) leakage current on pin DRAIN VDRAIN = 650 V - - 125 µA VBR(DRAIN) breakdown voltage on pin DRAIN Tj > 0 °C 650 - - V RDSon drain-source on-state resistance Isource = −0.5 A tf(DRAIN) fall time on pin DRAIN Tj = 25 °C - 6.5 7.5 Ω Tj = 100 °C - 9.0 10.0 Ω - 75 - ns VDRAIN = 300 V; no external capacitor at pin DRAIN Temperature protection Tprot protection temperature 150 160 170 °C Tprot(hys) hysteresis of protection temperature - 2 - °C 0.47 0.50 0.53 V Overcurrent and short winding protection: pin SOURCE VSOURCE(max) maximum voltage on pin SOURCE ∆V/∆t = 0.1 V/µs SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 10 of 15 SSL1623PH NXP Semiconductors Table 6. Characteristics …continued Measurement valid data Tamb = 25 °C; no overtemperature; all voltages are measured with respect to ground; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Vswp short-winding protection voltage ∆V/∆t = 0.5 V/µs 0.7 0.75 0.8 V td delay time ∆V/∆t = 0.5 V/µs - 160 185 ns tleb leading edge blanking time both overcurrent and short winding protection 250 350 450 ns 12. Application information LF D5 Z1 CF1 Vo C5 D1 CF2 mains R1 R2 CVCC VCC GND RRC RC R4 CRC REG D2 1 8 2 7 SSL1623PH 3 6 4 5 DRAIN C6 − Ycap n.c. RI SOURCE AUX RAUX R3 014aaa347 Fig 5. Typical configuration of SSL1623PH - primary sensing SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 11 of 15 SSL1623PH NXP Semiconductors 13. Package outline DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 9 16 pin 1 index E 1 8 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 4.7 0.51 3.7 1.40 1.14 0.53 0.38 0.32 0.23 21.8 21.4 6.48 6.20 2.54 7.62 3.9 3.4 8.25 7.80 9.5 8.3 0.254 2.2 inches 0.19 0.02 0.15 0.055 0.045 0.021 0.015 0.013 0.009 0.86 0.84 0.26 0.24 0.1 0.3 0.15 0.13 0.32 0.31 0.37 0.33 0.01 0.087 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. Fig 6. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT38-1 050G09 MO-001 SC-503-16 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-13 Package outline DIP16 SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 12 of 15 SSL1623PH NXP Semiconductors 14. Revision history Table 7. Revision history Document ID Release date Data sheet status Change notice Order number Supersedes SSL1623PH_1 20080915 Product data sheet - - - SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 13 of 15 SSL1623PH NXP Semiconductors 15. Legal information 15.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 15.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 15.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 15.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] SSL1623PH_1 Product data sheet © NXP B.V. 2008. All rights reserved. Rev. 01 — 15 September 2008 14 of 15 SSL1623PH NXP Semiconductors 17. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 8.2 8.3 8.4 8.5 8.6 8.6.1 8.6.2 8.6.3 8.6.4 8.7 8.7.1 8.7.2 8.7.3 8.7.4 9 10 11 12 13 14 15 15.1 15.2 15.3 15.4 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 4 Start-up and undervoltage lockout . . . . . . . . . . 5 Oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Duty factor control. . . . . . . . . . . . . . . . . . . . . . . 5 Valley switching. . . . . . . . . . . . . . . . . . . . . . . . . 5 Demagnetization. . . . . . . . . . . . . . . . . . . . . . . . 7 Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Overcurrent protection . . . . . . . . . . . . . . . . . . . 7 Short winding protection . . . . . . . . . . . . . . . . . . 7 Overtemperature protection . . . . . . . . . . . . . . . 7 Overvoltage protection . . . . . . . . . . . . . . . . . . . 8 Characteristics of the complete LED power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 8 Thermal characteristics. . . . . . . . . . . . . . . . . . . 9 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Application information. . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 13 Legal information. . . . . . . . . . . . . . . . . . . . . . . 14 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 14 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Contact information. . . . . . . . . . . . . . . . . . . . . 14 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 15 September 2008 Document identifier: SSL1623PH_1