GBPC12, 15, 25 AND 35 SERIES GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Current Voltage - 12.0 to 35.0 Amperes GBPC - W Wire leads GBPC - Standard FEATURES ♦ The plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL recognized under component index, file number E54214 ♦ Integrally molded heatsink provides very low thermal resistance for maximum heat dissipation ♦ Universal 3-way terminals; snap-on, wire wrap-around, or P.C.B. mounting ♦ High forward surge current capabilities ♦ Glass passivated chip junctions ♦ Typical IR less than 0.3µA ♦ High temperature soldering guaranteed: 260°C/10 seconds at 5lbs. (2.3 kg) tension MECHANICAL DATA Case: Molded plastic with heatsink integrally mounted in the bridge encapsulation Terminals: Either plated 0.25" (6.35mm). Faston lugs or plated copper leads 0.040" (1.02mm) diameter. Suffix letter "W" added to indicate leads (e.g. GBPC12005W). Mounting Position: See NOTE 3 Polarity: Polarity symbols molded on body Mounting Torque: 20 in. - lb. max. Weight: 0.53 ounce, 15 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. GBPC12, 15, 25, 35 02 04 06 SYMBOLS 005 01 08 10 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts VDC 50 100 200 400 600 800 1000 Volts Maximum DC blocking voltage Maximum average forward rectified output current GBPC12 GBPC15 GBPC25 GBPC35 (SEE FIG.1) Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) GBPC12 GBPC15 GBPC25 GBPC35 Rating (non-repetitive, for t greater than 1ms and less than 8.3ms) for fusing GBPC12 GBPC15 GBPC25 GBPC35 IF=6.0A IF=7.5A IF=12.5A IF=17.5A Maximum instantaneous forward voltage drop per leg at GBPC12 GBPC15 GBPC25 GBPC35 Maximum reverse DC current at rated DC blocking voltage per leg TA=25°C TA=125°C RMS isolation voltage from case to leads Typical junction capacitance per leg (NOTE 1) Typical thermal resistance per leg (NOTE 2) GBPC12-25 GBPC35 Operating junction storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to case per leg (3) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer efficiency with #10 screw 7/28/98 I(AV) IFSM 12.0 15.0 25.0 35.0 200.0 300.0 300.0 400.0 Amps Amps I2t 160.0 375.0 375.0 660.0 A2 sec VF 1.1 Volts IR 5.0 500.0 µA VISO 2500.0 Volts CJ 300.0 pF RΘJC 1.9 1.4 °C/W TJ, TSTG -55 to +150 °C RATINGS AND CHARACTERISTICS CURVES GBPC12, 15, 25 AND 35 SERIES FIG. 1 - MAXIMUM OUTPUT RECTIFIED CURRENT FIG. 2 - MAXIMUM OUTPUT RECTIFIED CURRENT 40 30 RthS-A=0.5 °C/W AVERAGE FORWARD CURRENT, AMPERES 35 AVERAGE FORWARD CURRENT, AMPERES 40 BRIDGES MOUNTED on 9 x 3.5 x 4.6” (22.9 x 8.9 x 11.7cm) AL. FINNED PLATE GBPC35 5 x 6 x 4.9” AL. FINNED PLATE GBPC25 25 5 x 4 x 3” AL. FINNED PLATE 20 GBPC15 15 6.0 x 2.2 x 2.2” AL. FINNED PLATE GBPC12 10 5 0 35 30 25 50 GBPC25 RthS-A=0.5 °C/W 25 20 GBPC15 RthS-A=1.0 °C/W 15 10 60 Hz RESISTIVE OR INDUCTIVE LOAD 0 60 HZ RESISTIVE OR INDUCTIVE LOAD GBPC35 5 0 75 100 125 150 175 200 GBPC12 RthS-A=1.0 °C/W 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE, °C CASE TEMPERATURE, °C FIG. 4 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG FIG. 3 - MAXIMUM POWER DISSIPATION 500 PEAK FORWARD SURGE CURRENT, AMPERES 80 AVERAGE POWER DISSIPATION OF BRIDGE, WATTS CAPACITIVE LOAD 70 60 TJ=TJ max. 50 40 30 RESISTIVE OR INDUCTIVE LOAD 20 TJ=TJ max. 0.5Single Sine-Wave (JEDEC Method) GBPC35 GBPC15 GBPC25 100 GBPC12 1.0 CYCLE 1 10 NUMBER OF CYCLES AT 60Hz 10 0 0 10 20 30 AVERAGE OUTPUT CURRENT, AMPERES 40 100 RATINGS AND CHARACTERISTICS CURVES GBPC12, 15, 25 AND 35 SERIES FIG. 6 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 5 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG TJ=125°C 100 TJ=150°C INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.01 0.4 0.6 0.8 1 1.2 1.4 1.6 50-400V 600-1000V 10 1 0.1 TJ=25°C INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 60 40 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 7 - TYPICAL JUNCTION CAPACITANCE PER LEG FIG. 8 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG TJ=25°C f=1.0 MHz Vsig=50mVp-p 100 50 1 10 REVERSE VOLTAGE, VOLTS 100 100 TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION, CAPACITANCE, pF 600 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100 GBPC FIG. 9 1.135 (28.8) 1.115 (28.3) Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) 0.672 (17.1) 0.632 (16.1) AC 1.135 (28.8) 1.115 (28.3) 0.672 (17.1) 0.632 (16.1) 0.582 (14.8) 0.542 (13.8) 0.732 (18.6) 0.692 (17.6) 0.094 (2.4) DIA. 0.034 (0.86) 0.25 (6.35) 0.030 (0.76) 0.840 (21.3) 0.740 (18.8) 0.310 (7.62) 0.290 (7.36) GBPC-W FIG. 10 1.135 (28.8) Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) 1.115 (28.3) 0.732 (18.6) 0.692 (17.6) 1.135 (28.8) 0.24 (6.0) 0.18 (4.6) 0.732 (18.6) 0.692 (17.6) 1.115 (28.3) 0.24 (6.0) 0.18 (4.6) 0.470 (11.9) 0.430 (10.9) 0.50 (12.7) 0.44 (11.7) 0.042 (1.07) 0.038 (0.97) DIA. 1.25 (31.8) MIN. 0.310 (7.62) 0.290 (7.36) Dimensions in inches and (millimeters) NOTES: (1) Corrosion resistant terminals designed with 0.25” female quick connectors for wrap or snap-on (2) A thin film of silicone thermal compound is recommended between the bridge case and mounting surface for improved thermal conduction