TOSHIBA TMP88CP38BFG

TMP88CS38B/CM38B/CP38B
CMOS 8-Bit Microcontroller
TMP88CS38BNG/FG, TMP88CM38BNG/FG, TMP88CP38BNG/FG
The TMP88CS38B/CM38B/CP38B is the high speed and high performance 8-bit single chip
microcomputers. This MCU contain CPU core, ROM, RAM, input/output ports, four Multi-function
timer/counters, serial bus interface, on-screen display, PWM output, 8-bit AD converter, and
remote control signal preprocessor on chip.
Product No.
ROM
RAM
2 K × 8 bits
TMP88CS38BNG/FG
64 K × 8 bits
TMP88CM38BNG/FG
32 K × 8 bits
TMP88CP38BNG/FG
48 K × 8 bits
1.5 K × 8 bits
Package
SDIP42-P-600-1.78
P-QFP44-1414-0.80K
OTP MCU
TMP88PS38BNG/FG
Features
♦
8-bit single chip microcomputer TLCS-870/X series
♦
Instruction execution time: 0.25 μs (at 16 MHz)
♦
842 basic instructions
•
Multiplication and division (8 bits × 8 bits, 16 bits × 8 bits, 16 bits/8 bits)
•
Bit manipulations (Set/clear/complement/move/test/exclusive or)
•
16-bit data and 20-bit data operations
•
1-byte jump/subroutine call (Short relative jump/vector call)
RESTRICTIONS ON PRODUCT USE
20070701-EN
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety
in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such
TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer,
personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These
TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high
quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury
(“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical
instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall
be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No responsibility
is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its
use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third
parties.
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations that
regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring
as a result of noncompliance with applicable laws and regulations.
88CS38B-1
2007-09-12
TMP88CS38B/CM38B/CP38B
♦
I/O ports: Maximum 33 (High current output: 4)
♦
17 interrupt sources: External 6, internal 11
•
All sources have independent latches each, and nested interrupt control is available.
•
Edge-selectable external interrupts with noise reject
•
High-speed task switching by register bank changeover
♦
ROM corrective function
♦
Two 16-bit timer/counters: TC1, TC2
•
♦
Timer, event counter, pulse width measurement, external trigger timer, window modes
Two 8-bit timer/counters: TC3, TC4
•
Timer, event counter, capture (Pulse width/duty measurement) mode
♦
Time base timer (Interrupt frequency: 0.95 Hz to 31250 Hz)
♦
Watchdog timer
•
♦
Serial bus interface
•
♦
Interrupt source/reset output
I2C bus, 8-bit SIO mode (Selectable two I/O channels)
On-screen display circuit
•
Font ROM characters: 384 characters
•
Characters display: 32 columns × 12 lines
•
Composition: 16 × 18 dots
•
Size of character: 3 kinds (Line by line)
•
Color of character: 8 or 15 kinds (Character by character)
•
Variable display position: Horizontal 256 steps, Vertical 512 steps
•
Fringing, smoothing, slant, underline, blinking function
♦
Jitter elimination
♦
Data slicer circuit 1 channel
♦
DA conversion (Pulse width modulation) outputs
•
14- or 12-bit resolution (2 channels)
•
12-bit resolution (2 channels)
•
7-bit resolution (6 channels)
♦
8-bit successive approximate type AD converter with sample and hold
♦
Remote control signal preprocessor
♦
Two power saving operating modes
•
STOP mode: Oscillation stops. Battery/capacitor back up. Port output hold/high
impedance.
•
IDLE mode: CPU stops, and peripherals operate using high-frequency clock. Release by
interrupts.
♦
Operating Voltage: 4.5 to 5.5 V at 16 MHz
♦
Emulation POD: BM88CS38N0A-M15
88CS38B-2
2007-09-12
TMP88CS38B/CM38B/CP38B
Pin Assignments
Package
SDIP42-P-600-1.78
TMP88CS38BNG
TMP88CP38BNG
TMP88CM38BNG
TMP88PS38BNG
SDIP42-P-600-1.78
VSS
( PWM0 ) P40
( PWM1 ) P41
( PWM2 ) P42
( PWM3 ) P43
( PWM 4 ) P44
( PWM5 ) P45
( PWM6 ) P46
( PWM7 ) P47
(TC2/ INT0 / PWM8 ) P50
(SI1/SCL1/ PWM9 ) P51
(SO1/SDA1) P52
( KWU0 / SCK1 /INT2/TC1/AIN0) P53
( KWU1 /AIN1) P54
( KWU2 /AIN2) P55
( KWU3 /AIN3) P56
( KWU 4 /Y/BLIN/AIN4) P60
( KWU5 /BIN/AIN5) P61
(GIN/CSOUT) P62
(RIN) P63
(I) P57
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
VDD
P33 (TC4/VIN0)
P32 (VIN1/CSIN)
VVSS
P35 (SDA0)
P34 (SCL0)
P31 (INT4/TC3)
P30 (INT3/RXIN)
P20 ( INT5 / STOP )
RESET
XOUT
XIN
TEST
OSC2
OSC1
P71 ( VD )
P70 ( HD )
P67 (Y/BL)
P66 (B)
P65 (G)
P64 (R)
Package
P-QFP44-1414-0.80K
34
35
36
37
38
39
40
41
42
43
44
RESET
XOUT
XIN
TEST
OSC2
OSC1
P71 (VD)
22
21
20
19
18
17
16
15
14
13
12
P70 ( HD )
P67 (Y/BL)
P66 (B)
P65 (G)
P64 (R)
N.C.
P57
P63 (RIN)
P62 (GIN/CSOUT)
P61 (BIN//AIN5/ KWU5 )
P60 (Y/BLIN/AIN4/ KWU4 )
(PWM4) P44
(PWM5) P45
(PWM6) P46
(PWM7) P47
(TC2/INT0/PWM8) P50
(SI1/SCL1/PWM9) P51
(SO1/SDA1) P52
(KWU0/SCK1/INT2/TC1/AIN0) P53
(KWU1/AIN1) P54
(KWU2/AIN2) P55
(KWU3/AIN3) P56
(SDA0) P35
VVSS
(VIN1/CSIN) P32
(TC4/VIN0) P33
N.C.
VDD
VSS
( PWM0 ) P40
( PWM1 ) P41
( PWM2 ) P42
( PWM3 ) P43
1
2
3
4
5
6
7
8
9
10
11
TMP88CS38BFG
TMP88CP38BFG
TMP88CM38BFG
TMP88PS38BFG
33
32
31
30
29
28
27
26
25
24
23
P34 (SCL0)
P31 (INT4/TC3)
P30 (INT3/RXIN)
P20 (INT5/STOP)
P-QFP44-1414-0.80K
88CS38B-3
2007-09-12
TMP88CS38B/CM38B/CP38B
Pin Functions (1/2)
Pin Name
P20 ( INT5 / STOP )
I/O
I/O (Input)
P35 (SDA0)
I/O (Input/Output)
P34 (SCL0)
I/O (Input/Output)
P33 (TC4/VIN0)
I/O (Input)
P32 (VIN1/CSIN)
I/O (Input)
P31 (INT4/TC3)
I/O (Input)
P30 (INT3/RXIN)
I/O (Input)
P47 ( PWM7 )
I/O (Output)
P46 ( PWM6 )
I/O (Output)
P45 ( PWM5 )
I/O (Output)
P44 ( PWM4 )
I/O (Output)
P43 ( PWM3 )
I/O (Output)
P42 ( PWM2 )
I/O (Output)
P41 ( PWM1 )
I/O (Output)
P40 ( PWM0 )
I/O (Output)
P57 (I)
I/O (Output)
P56 ( KWU3 /AIN3)
I/O (Input)
P55 ( KWU2 /AIN2)
I/O (Input)
P54 ( KWU1 /AIN1)
I/O (Input)
P53 ( KWU0 /AIN0/TC1
/INT2/ SCK1 )
P52 (SDA1/SO1)
I/O
(Input /Input/Input
/Input/Output)
Function
1-bit input/output port with latch. When
External interrupt input 5 or STOP
used as an input port, the latch must be
mode release signal input
set to “1”.
6-bit programmable input/output port.
Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured as
inputs. When used as a serial bus
interface input/output, the latch must
be set to “1”.
2
I C bus serial data input/output 0
2
I C bus serial clock input/output 0
Timer counter input 4 or video signal
Input 0
Video signal input 1 or composite sync
input
External interrupt input 4 or timer
counter input 3
External interrupt input 3 or remote
control signal preprocessor input
8-bit programmable input/output port.
Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured as
inputs. When used as a PWM output,
the latch must be set to “1”.
7-bit DA conversion (PWM) outputs
12-bit DA conversion (PWM) outputs
14/12-bit DA conversion (PWM)
outputs
8-bit programmable input/output port.
Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured as
inputs. When used as a PWM output, a
serial bus interface input/output, the
latch must be set to “1”.
Translucent signal output
Key-on wakeup inputs or AD converter
analog inputs
Key-on wakeup input or AD converter
analog input or timer counter input 1 or
external interrupt input 2 or SIO serial
clock input/output 1
2
I C bus serial data input/output 1 or
SIO serial data output 1
I/O
(Input/Output /Output)
P51 ( PWM9 /SCL1/SI1)
I/O (Output/Input/Output
/Input)
7-bit DA conversion (PWM) output or
2
I C bus serial data input/output 1 or
SIO serial data input 1
P50 ( PWM8 /TC2/ INT0 )
I/O
(Output/Input /Input)
7-bit DA conversion (PWM) output or
timer counter input 2 or external
interrupt input 0
P67 (Y/BL)
I/O (Output)
P66 (B)
I/O (Output)
P65 (G)
I/O (Output)
P64 (R)
I/O (Output)
P63 (RIN)
P62 (GIN/CSOUT)
I/O (Input)
I/O (Input/Output)
P61 ( KWU5 /BIN/AIN5)
I/O (Input)
P60
( KWU4 /YBLIN/AIN4)
I/O (Input)
8-bit programmable input/output port.
(P67 to P64: Tri-State, P63 to P60:
High current output) Each bit of these
ports can be individually configured as
an input or an output under software
control. During reset, all bits are
configured as inputs. When used P64
to P67 as port, each bit of the P6 port
data selection register (Bit7 to 4 in
ORP6S) must be set to “1”.
Y or BL output
R/G/B outputs
R input
G input or TEST video signal output
Key-on wakeup input 5 or B input or AD
converter analog input 5
Key-on wakeup input 4 or Y/BL input or
AD converter analog input 4
88CS38B-4
2007-09-12
TMP88CS38B/CM38B/CP38B
Pin Functions (2/2)
Pin Name
I/O
P71 ( VD )
I/O (Input)
P70 ( HD )
I/O (Input)
XIN, XOUT
Input, Output
RESET
TEST
I/O
Input
Function
2-bit programmable input/output port.
Each bit of these ports can be
individually configured as an input or
an output under software control.
During reset, all bits are configured as
inputs.
Vertical synchronous signal input
Horizontal synchronous signal input
Resonator connecting pins. For inputting external clock, XIN is used and XOUT
is opened.
Reset signal input or watchdog timer output/address-trap-reset
output/system-clock-reset output
Test pin for out-going test. Be tied to low.
OSC1, OSC2
Input, Output
Resonator connecting pins for on-screen display circuitry
VDD, VSS, VVSS
Power supply
+5 V, 0 V (GND)
88CS38B-5
2007-09-12
TMP88CS38B/CM38B/CP38B
Block Diagram
I/O ports
P64 to P67 P70, P71 P57
OSC connecting
pins for on-screen
display
Display
memory
OSC1
OSC2
Power
supply
VDD
VSS
VVSS
R, G, B,
Jitter
Y/BL
elimination
Character
ROM
VD
HD
On-screen display circuit
P6
TLCS-870/X
CPU core
Data memory
(RAM)
Data slicer
Program counter
Interrupt Controller
System controller
P5
ROM corrective circuit
Reset I/O test pin
RESET
TEST
P7
Standby controller
Resonator
connecting pins
XIN
XOUT
Time base
timer
Timing generator
High
Clock
frequency generator
Watchdog
timer
16-bit
timer
TC1 TC2
Program memory
(ROM)
8-bit
timer/counter
TC3
TC4
Inst. register
Inst. decoder
P2
P4
DA converter
(PWM)
P5
8-bit
AD
Key-on
wakeup
P6
Video signal
output
Remote
control signal
P32
P20 P40 to P47
P50 to P56
P60 to P63
Serial bus
interface
P3
P30 to P35
Y/BLIN
RIN
GIN
BIN
P33
Video
signal
I/O ports
88CS38B-6
2007-09-12
TMP88CS38B/CM38B/CP38B
Operational Description
1.
CPU Core Functions
The CPU core consists of a CPU, a system clock controller, and an interrupt controller.
This section provides a description of the CPU core, the program memory, the data memory, the
external memory interface, and the reset circuit.
1.1
Memory Address Map
The TMP88CS38B/CM38B/CP38B memory consists of four blocks: ROM, RAM, SFR (Special
function register), and DBR (Data buffer register). They are all mapped to a 1-Mbyte address
space. Figure 1.1.1 shows the TMP88CS38B/CM38B/CP38B memory address map. There are
16 banks of the general-purpose register. The register banks are also assigned to the RAM
address space.
00000H
SFR
RAM
0003FH
00040H
000BFH
000C0H
64 bytes
128 bytes
0003FH
00040H
000BFH
000C0H
2048 bytes
64 bytes
128 bytes
000BFH
000C0H
128 bytes
128 bytes
General-purpose
register banks
(8 registers × 16 banks)
1536 bytes
00F80H
128 bytes
128 bytes
00FFFH
00FFFH
00FFFH
04000H
04000H
04000H
32512 bytes
program area
48896 bytes
program area
65280 bytes
program area
64 bytes
006BFH
00F80H
00F80H
0003FH
00040H
1536 bytes
006BFH
008BFH
DBR
00000H
00000H
0BEFFH
0FEFFH
13EFFH
20000H
ROM
24576 bytes
OSD font area
25FFFH
FFF7FH
FFF80H
24576 bytes
OSD font area
FFF00H
64 bytes
64 bytes
FFF3FH
FFF40H
FFF7FH
FFF80H
128 bytes
FFFFFH
24576 bytes
OSD font area
FFF00H
64 bytes
64 bytes
FFF3FH
FFF40H
FFF7FH
FFF80H
64 bytes
Vector table for
interrupts
64 bytes
Vector table for vector
call instruction
128 bytes
128 bytes
FFFFFH
TMP88CS38B
20000H
25FFFH
25FFFH
FFF00H
FFF3FH
FFF40H
20000H
FFFFFH
TMP88CP38B
Vector table for
interrupts
TMP88CM38B
ROM: Read only memory includes
Program memory, Character data memory for OSD
RAM: Random access memory includes
Data memory, Stack, General-purpose register banks
SFR: Special function register includes
I/O ports, Peripheral hardware control registers, Peripheral hardware status registers,
System control registers, Interrupt control registers, Program status word
DBR: Data buffer register includes
Control resister for on-screen display(OSD)
Remote-control-receive control/status resigsters, ROM correction control registers,
Test video signal control registers
Figure 1.1.1 Memory Address Map
88CS38B-7
2007-09-12
TMP88CS38B/CM38B/CP38B
1.2
Program Memory (ROM)
The TMP88CS38B contains a 64-Kbyte program memory (Mask ROM) at addresses from
04000H to 13EFFH and FFF00H to FFFFFH.
The TMP88CM38B contains a 32-Kbyte program memory (Mask ROM) at address from
04000H to 0BEFFH and FFF00H to FFFFFH. The TMP88CP38B contains a 48-Kbyte program
memory (Mask ROM) at address from 04000H to 0FEFFH and FFF00H to FFFFFH.
Addresses FFF00H through FFFFFH in the program memory are also used for a particular
purpose.
1.3
Data Memory (RAM)
The TMP88CS38B has a 2-Kbyte data memory (Static RAM) address from 0040H to 08BFH.
The TMP88CM38B/CP38B has a 1.5-Kbyte data memory (Static RAM) address from 0040H
to 06BFH.
The first 128 bytes (Addresses 00040H through 000BFH) in the built-in RAM are also
available as general-purpose register banks.
The general-purpose registers are mapped in the RAM; therefore, do not clear RAM at the
current bank addresses.
Example: Clears RAM to “00H” except the bank0 (TMP88CS38B/CM38B/CP38B):
LD
HL, 0048H
; Sets start address to HL register pair
LD
A, H
; Sets initial data (00H) to A register
LD
BC, 0877H
; Sets number of byte to BC register pair
SRAMCLR: LD
(HL+), A
DEC BC
JRS
F, SRAMCLR
Note:
1.4
The data memory contents become unstable when the power supply is turned on; therefore,
the data memory should be initialized by an initialization routine. Note that the
general-purpose registers are mapped in the RAM; therefore, do not clear RAM at the
current bank addresses.
System Clock Controller
The system clock controller consists of a clock generator, a timing generator, and a standby
controller.
Timing generator control register
TBTCR
Clock
generator
XIN
00036H
fc
High-frequency
clock oscillator
Timing
generator
Standby controller
XOUT
00038H
System clocks
Clock generator control
00039H
SYSCR1
SYSCR2
System control registers
Figure 1.4.1 System Clock Controller
88CS38B-8
2007-09-12
TMP88CS38B/CM38B/CP38B
1.4.1
Clock Generator
The clock generator generates the basic clock which provides the system clocks supplied
to the CPU core and peripheral hardware. It contains oscillation circuit: one for the
high-frequency clock.
The high-frequency (fc) clock can be easily obtained by connecting a resonator between
the XIN/XOUT pin, respectively. Clock input from an external oscillator is also possible. In
this case, external clock is applied to the XIN/XTIN pin not connected. The
TMP88CS38B/CM38B/CP38B is not provided an LC oscillation.
High-frequency clock
XIN
XOUT
XIN
XOUT
(Open)
(a) Crystal/Ceramic
resonator
(b) External oscillator
Figure 1.4.2 Examples of Resonator Connection
Note: Accurate adjustment of the oscillation frequency:
Although hardware to externally and directly monitor the basic clock pulse is not
provided, the oscillation frequency can be adjusted by making the program to output
fixed frequency pulses to the port while disabling all interrupts and monitoring this pulse.
With a system requiring adjustment of the oscillation frequency, the adjusting program
must be created beforehand.
1.4.2
Timing Generator
The timing generator generates from the basic clock the various system clocks supplied
to the CPU core and peripheral hardware. The timing generator provides the following
functions:
1.
Generation of main system clock
2.
Generation of source clocks for time base timer
3.
Generation of source clocks for watchdog timer
4.
Generation of internal source clocks for timer/counters TC1 to TC4
5.
Generation of warm-up clocks for releasing STOP mode
6.
Generation of a clock for releasing reset output
(1) Configuration of timing generator
The timing generator consists of a 21-stage divider with a divided by 3 prescaler, a
main system clock generator, and machine cycle counters.
During reset and at releasing STOP mode, the prescaler and the divider are cleared
to “0”, however, the prescaler is not cleared.
An input clock to the 7th stage of the divider depends on the operating mode.
A divided by 256 of high-frequency clock (fc/28) is input to the 7th stage of the divider.
88CS38B-9
2007-09-12
TMP88CS38B/CM38B/CP38B
fm
Machine cycle counters
States
DV1CK
Prescaler
High-frequency
clock
Machine cycles
fc
0 1 2
Divider
S
A
Y
Divider
1 2 3 4 5 6
fc/2
8
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
B
Reset circuit
standby
controller
Timer/
counters
Watchdog
timer
Time base
timer
fc
MK8 MHz
SLICER
FC8OUT
D1
D0
SG
JITTA
Figure 1.4.3 Configuration of Timing Generator
CGCR
(00030H)
“0”
“0”
DV1CK
DV1CK
“0”
“0”
“0”
“0”
“0”
Selection of input clock to 0: fc/4
the 1st stage of the divider. 1: fc/8
(Initial value: 0000 0000)
R/W
Note 1:
fc: High-frequency clock [Hz], *: Don’t care
Note 2:
The all bits except DV1CK are cleared to “0”.
Figure 1.4.4 Divider Control Register
FC8CR
(00FEEH)
D1
D1
D0
FC8OUT
1
0
1/2 fc
0
0
1/1 fc
D0
Read/Write (Initial value: 0000 0010)
Figure 1.4.5 FC8 Control Register
88CS38B-10
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Machine cycle
Instruction execution and peripheral hardware operation are synchronized with the
main system clock. The minimum instruction execution unit is called a “machine cycle”.
There are a total of 15 different types of instructions for the TLCS-870/X series:
Ranging from 1-cycle instructions which require one machine cycle for execution to
15-cycle instructions which require 15 machine cycles for execution.
A machine cycle consists of 4 states (S0 to S3), and each state consists of one main
system clock.
1/fc
Main System clock
fm
S0
State
S1
S2
S3
S0
S1
S2
S3
Machine cycle
(0.25 μs at fc = 16 MHz)
Figure 1.4.6 Machine Cycle
1.4.3
Standby Controller
The standby controller starts and stops the switches the main system clock. These modes
are controlled by the system control registers (SYSCR1, SYSCR2).
Figure 1.4.7 shows the operating mode transition diagram and Figure 1.4.8 shows the
system control registers.
(1) Single-clock mode
In the single-clock mode, the machine cycle time is 4/fc [s] (0.25 μs at fc = 16 MHz).
1.
NORMAL mode
In this mode, both the CPU core and on-chip peripherals operate using the
high-frequency clock.
2.
IDLE mode
In this mode, the internal oscillation circuit remains active. The CPU and the
watchdog timer are halted; however, on-chip peripherals remain active (Operate
using the high-frequency clock). IDLE mode is started by setting IDLE bit in the
system control register 2 (SYSCR2), and IDLE1 mode is released to NORMAL
mode by an interrupt request from on-chip peripherals or external interrupt
inputs. When IMF (Interrupt master enable flag) is “1” (Interrupt enable), the
execution will resume upon acceptance of the interrupt, and the operation will
return to normal after the interrupt service is completed. When IMF is “0”
(Interrupt disable), the execution will resume with the instruction which follows
IDLE mode start instruction.
3.
STOP mode
In this mode, the internal oscillation circuit is turned off, causing all system
operations to be halted. The internal status immediately prior to the halt is held
with the lowest power consumption during this mode.
STOP mode is started by setting STOP bit in the system control register 1
(SYSCR1), and STOP mode is released by an input (Either level-sensitive or
edge-sensitive can be programmably selected) to the STOP pin. After the warm-up
period is completed, the execution resumes with the next instruction which
follows the STOP mode start instruction.
88CS38B-11
2007-09-12
TMP88CS38B/CM38B/CP38B
RESET
Reset release
Software
IDLE
mode
NORMAL
mode
Interrupt
Software
STOP
STOP
mode
pin input
(a) Single-clock mode
Note: NORMAL mode are generically called NORMAL; STOP mode is called STOP; and IDLE mode is
called IDLE.
Operating Mode
Frequency
CPU Core
High-frequency
RESET
Single clock
NORMAL
Reset
Turning on oscillation
IDLE
STOP
On-chip
Machine
Peripherals Cycle Time
Turning off oscillation
Operate
Halt
Reset
Operate
Halt
4/fc [s]
−
Figure 1.4.7 Operating Mode Transition Diagram
88CS38B-12
2007-09-12
TMP88CS38B/CM38B/CP38B
System Control Register 1
SYSCR1
(00038H)
7
6
5
4
STOP
RELM
“0”
“1”
3
2
1
0
WUT
(Initial value: 0000 00**)
0: CPU core and peripherals remain active
STOP
STOP mode start
RELM
Release method for STOP mode
1: CPU core and peripherals are halted
(Start STOP mode)
0: STOP Edge-sensitive release (Rising edge)
1: STOP Level-sensitive release (“H” level)
Return to NORMAL mode
Warm-up time at releasing STOP
mode
WUT
00
DV1CK = 0
DV1CK = 1
3 × 2 /fc
16
3 × 2 /fc
16
2 /fc
17
17
2 /fc
01
14
10
2 /fc
11
Reserved
R/W
15
2 /fc
Reserved
Note 1:
Always set bit5 in SYSCR1 to “0”.
Note 2:
When STOP mode is released with RESET pin input, a return is made to NORMAL mode regardless of the
RETM contents.
Note 3:
fc: High-frequency clock [Hz]
*: Don’t care
Note 4:
Bits 1 and 0 in SYSCR1 are read in as undefined data when a read instruction is executed.
Note 5:
Always set bit4 in SYSCR1 to “1” when STOP mode is started.
System Control Register 2
SYSCR2
(00039H)
7
6
5
4
“1”
“0”
“0”
IDLE
IDLE
IDLE mode start
3
2
1
0
(Initial value: 1000 ****)
0: CPU and watchdog timer remain active
1: CPU and watchdog timer are stopped (Start IDLE mode)
Note 1:
*: Don’t care
Note 2:
Always set bit7, 6 and 5 in SYSCR2 to “100”.
R/W
Figure 1.4.8 System Control Registers
88CS38B-13
2007-09-12
TMP88CS38B/CM38B/CP38B
1.4.4
Operating Mode Control
(1) STOP mode
STOP mode is controlled by the system control register 1 (SYSCR1) and the STOP
pin input. The STOP pin is also used both as a port P20 and an INT5 (External
interrupt input 5) pin. STOP mode is started by setting STOP (Bit7 in SYSCR1 ) to “1”.
During STOP mode, the following status is maintained.
1.
Oscillations are turned off, and all internal operations are halted.
2.
The data memory, registers and port output latches are all held in the status in
effect before STOP mode was entered.
3.
The prescaler and the divider of the timing generator are cleared to “0”.
4.
The program counter holds the address of the instruction following the instruction
which started the STOP mode.
STOP mode includes a level-sensitive release mode and an edge-sensitive release
mode, either of which can be selected with RELM (Bit6 in SYSCR1).
a.
Level-sensitive release mode (RELM = 1)
In this mode, STOP mode is released by setting the STOP pin high. This mode
is used for capacitor back up when the main power supply is cut off and long term
battery back up.
When the STOP pin input is high, executing an instruction which starts the
STOP mode will not place in STOP mode but instead will immediately start the
release sequence (Warm up). Thus, to start STOP mode in the level-sensitive
release mode, it is necessary for the program to first confirm that the STOP pin
input is low. The following method can be used for confirmation:
Using an external interrupt input INT5 ( INT5 is a falling edge-sensitive input).
Example: Starting STOP mode with an INT5 interrupt.
PINT5:
SINT5:
TEST
(P2). 0
JRS
F, SINT5
;
To reject noise, the STOP mode does not start
if port P20 is at high
LD
(SYSCR1), 01010000B
;
Sets up the level-sensitive release mode
SET
(SYSCR1). 7
;
Starts STOP mode
LDW
(IL), 1110011101010111B
;
IL12, 11, 7, 5, 3 ← 0 (Clears interrupt latches)
RETI
VIH
STOP pin
XOUT pin
NORMAL
operation
STOP
operation
Confirm by program that the
STOP pin input is low and
start STOP mode.
Warm up
NORMAL
operation
STOP mode is released by the hardware.
Always released if the STOP
pin input is high.
Note 1:
After warm up is started, when STOP pin input is changed “L” level, STOP mode is not placed.
Note 2:
When changing to the level-sensitive release mode from the edge-sensitive release mode, the release
mode is not switched until a rising edge of the STOP pin input is detected.
Figure 1.4.9 Level-sensitive Release Mode
88CS38B-14
2007-09-12
TMP88CS38B/CM38B/CP38B
b.
Edge-sensitive release mode (RELM = 0)
In this mode, STOP mode is released by a rising edge of the STOP pin input.
This is used in applications where a relatively short program is executed
repeatedly at periodic intervals. This periodic signal (for example, a clock from a
low-power consumption oscillator) is input to the STOP pin.
In the edge-sensitive release mode, STOP mode is started even when the STOP
pin input is high.
Example: Starting STOP mode from NORMAL mode
LD
(SYSCR1), 10010000B
;
Starts after specified to the edge-sensitive mode
VIH
STOP pin
XOUT pin
STOP
operation
NORMAL
operation
Warm up
STOP mode started
by the program.
STOP
operation
NORMAL
operation
STOP mode is released by the hardware at the rising
edge of STOP pin input.
Figure 1.4.10 Edge-sensitive Release Mode
STOP mode is released by the following sequence:
1.
When returning to NORMAL, clock oscillator is turned on.
2.
A warm-up period is inserted to allow oscillation time to stabilize. During
warm-up, all internal operations remain halted. Two different warm-up times can
be selected with WUT (Bits 2 and 3 in SYSCR1) as determined by the resonator
characteristics.
3.
When the warm-up time has elapsed, normal operation resumes with the
instruction following the STOP mode start instruction (e.g., [SET (SYSCR1). 7]).
The start is made after the divider of the timing generator is cleared to “0”.
Table 1.4.1 Warm-up Time Example
Warm-up Time [s]
WUT
Return to NORMAL mode
DV1CK = 0
00
Note:
3 × 2 /fc
16
DV1CK = 1
(12.29 m)
3 × 2 /fc
17
(24.58 m)
17
(8.20 m)
15
(2.05 m)
16
(4.10 m)
2 /fc
14
(1.02 m)
2 /fc
01
2 /fc
10
2 /fc
11
Reserved
(
-
)
Reserved
(
-
)
The warm-up time is obtained by dividing the basic clock by the divider: therefore,
the warm-up time may include a certain amount of error if there is any fluctuation of
the oscillation frequency when STOP mode is released. Thus, the warm-up time
must be considered an approximate value.
88CS38B-15
2007-09-12
88CS38B-16
Divider
0
Instruction Halt
execution
Program
counter
Oscillator
Turn
circuit
off
Main
system
clock
input
STOP pin
Divider
Instruction
execution
Program
counter
Main
system
clock
Oscillator
circuit
Turn on
Turn on
n
Count up
Warm up
a+2
n+2
n+3
a+3
(b) STOP mode release
0
1
Instruction at address a + 2
a+4
a+5
n+4
2
Instruction at address a + 3
(a) STOP mode start (Example: Start with SET (SYSCR1). 7 instruction located at address a)
n+1
SET (SYSCR1). 7
a+3
3
Instruction at address a + 4
a+6
0
Halt
Turn off
TMP88CS38B/CM38B/CP38B
Figure 1.4.11 STOP Mode Start/Release
2007-09-12
TMP88CS38B/CM38B/CP38B
STOP mode can also be released by setting the RESET pin low, which immediately
performs the normal reset operation.
Note:
When STOP mode is released with a low hold voltage, the following cautions must
be observed.
The power supply voltage must be at the operating voltage level before releasing
STOP mode. The RESET pin input must also be high, rising together with the
power supply voltage. In this case, if an external time constant circuit has been
connected, the RESET pin input voltage will increase at a slower rate than the
power supply voltage. At this time, there is a danger that a reset may occur if input
voltage level of the RESET pin drops below the non-inverting high-level input
voltage (hysteresis input).
(2) IDLE mode
IDLE mode is controlled by the system control register 2 and maskable interrupts.
The following status is maintained during IDLE mode.
1.
Operation of the CPU and watchdog timer is halted. On-chip peripherals continue
to operate.
2.
The data memory, CPU registers and port output latches are all held in the status
in effect before IDLE mode was entered.
3.
The program counter holds the address of the instruction following the instruction
which started IDLE mode.
Example: Starting IDLE mode.
SET
(SYSCR2). 4
;
IDLE ← 1
Starting IDLE mode
by instruction
CPU, WDT are halted
Reset input
Yes
Reset
No (High)
No
Interrupt request
Normal
release mode
No
Yes
IMF = 1
Yes (Interrupt release mode)
Interrupt processing
Execution of the
instruction which follows
the IDLE mode start
instruction
Figure 1.4.12 IDLE Mode
88CS38B-17
2007-09-12
TMP88CS38B/CM38B/CP38B
IDLE mode includes a normal release mode and an interrupt release mode. Selection
is made with the interrupt master enable flag (IMF). Releasing the IDLE mode returns
from IDLE to NORMAL.
a.
Normal release mode (IMF = “0”)
IDLE mode is released by any interrupt source enabled by the individual
interrupt enable flag (EF) or an external interrupt 0 ( INT0 pin) request.
Execution resumes with the instruction following the IDLE mode start instruction
(e.g., [SET (SYSCR2).4]). Normally, IL (Interrupt latch) of interrupt source to
release IDLE mode must be cleared by load instructions.
b.
Interrupt release mode (IMF = “1”)
IDLE mode is released and interrupt processing is started by any interrupt
source enabled with the individual interrupt enable flag (EF) or an external
interrupt 0 ( INT0 pin) request. After the interrupt is processed, the execution
resumes from the instruction following the instruction which started IDLE mode.
Note:
When a watchdog timer interrupt is generated immediately before the IDLE mode is
started, the watchdog timer interrupt will be processed but IDLE mode will not be
started.
88CS38B-18
2007-09-12
88CS38B-19
Watchdog
timer
Instruction
execution
Program
counter
Interrupt
request
Halt
Halt
Halt
Watchdog
timer
Main
system
clock
Halt
Instruction
execution
Program
counter
Interrupt
request
Main
system
clock
a+3
(b) IDLE mode release
(II) Interrupt release mode
a+3
a+3
Operate
Operate
Acceptance of interrupt
Instruction at address a + 2
a+4
(a) IDLE mode start (Example: starting with the SET instruction located at address a)
(I) Normal release mode
Operate
SET (SYSCR2). 4
Instruction
execution
Watchdog
timer
a+2
Program
counter
Interrupt
request
Main
system
clock
Halt
TMP88CS38B/CM38B/CP38B
Figure 1.4.13 IDLE Mode Start/Release
2007-09-12
TMP88CS38B/CM38B/CP38B
IDLE mode can also be released by setting the RESET pin low, which immediately
performs the reset operation. After reset, the TMP88CS38B/CM38B/CP38B is placed
in NORMAL mode.
88CS38B-20
2007-09-12
TMP88CS38B/CM38B/CP38B
1.5
Interrupt Controller
The TMP88CS38B/CM38B/CP38B has a total of 17 interrupt sources; 6 externals and 11
internals. Multiple interrupts with priorities are also possible. Two of the internal sources are
pseudo non-maskable interrupts; the remainder are all maskable interrupts.
Table 1.5.1 Interrupt Sources
Interrupt Source
Internal/
External
(Reset)
Internal
INTSW
(Software interrupt)
Enable Condition
Non maskable
Pseudo non maskable
Interrupt
Latch
Vector Table
Address
−
FFFFCH
High 0
−
FFFF8H
1
2
Priority
Internal
INTWDT
(Watchdog timer interrupt)
IL2
FFFF4H
External
INT0
(External interrupt 0)
IMF ·EF3 = 1, INT0EN = 1
IL3
FFFF0H
3
Internal
INTTC1
(16-bit TC1 interrupt)
IMF ·EF4 = 1
IL4
FFFECH
4
External
INTKWU
(Key-on wakeup)
IMF ·EF5 = 1
IL5
FFFE8H
5
Internal
INTTBT
(Time base timer interrupt)
IMF ·EF6 = 1
IL6
FFFE4H
6
External
INT2
(External interrupt 2)
IMF ·EF7 = 1
IL7
FFFE0H
7
Internal
INTTC3
(8-bit TC3 interrupt)
IMF ·EF8 = 1
IL8
FFFDCH
8
Internal
INTTSBI
(SBI interrupt)
IMF ·EF9 = 1
IL9
FFFD8H
9
Internal
INTTC4
(8-bit TC4 interrupt)
IMF ·EF10 = 1
IL10
FFFD4H
10
External
INT3
(External interrupt 3)
IMF ·EF11 = 1
IL11
FFFD0H
11
External
INT4
(External interrupt 4)
IMF ·EF12 = 1
IL12
FFFCCH
12
Internal
INTADC
(AD converter interrupt)
IMF ·EF13 = 1
IL13
FFFC8H
13
Internal
INTTC2
(16-bit TC2 interrupt)
IMF ·EF14 = 1
IL14
FFFC4H
14
External
INT5
(External interrupt 5)
IMF ·EF15 = 1
IL15
FFFC0H
15
Internal
INTOSD
(OSD interrupt)
IMF ·EF16 = 1
IL16
FFFBCH
16
Internal
INTSLI
(Slicer interrupt)
IMF ·EF17 = 1
IL17
FFFB8H
17
Reserved
IMF ·EF18 = 1
IL18
FFFB4H
18
Reserved
IMF ·EF19 = 1
IL19
FFFB0H
19
Reserved
IMF ·EF20 = 1
IL20
FFFACH
20
Reserved
IMF ·EF21 = 1
IL21
FFFA8H
21
Reserved
IMF ·EF22 = 1
IL22
FFFA4H
22
Reserved
IMF ·EF23 = 1
IL23
FFFA0H
23
Reserved
IMF ·EF24 = 1
IL24
FFF9CH
24
Reserved
IMF ·EF25 = 1
IL25
FFF98H
25
Reserved
IMF ·EF26 = 1
IL26
FFF94H
26
Reserved
IMF ·EF27 = 1
IL27
FFF90H
27
Reserved
IMF ·EF28 = 1
IL28
FFF8CH
28
Reserved
IMF ·EF29 = 1
IL29
FFF88H
29
Reserved
IMF ·EF30 = 1
IL30
FFF84H
30
Reserved
IMF ·EF31 = 1
IL31
FFF80H
Low 31
Note: Before you change each enable flag (EF) and/or each interrupt latch (IL), be sure to clear the
interrupt master enable flag (IMF) to “0” (to disable interrupts).
a. After a DI instruction is executed.
b. When an interrupt is accepted, IMF is automatically cleared to “0”.
However to enable nested interrupts, change EF and/or IL before setting IMF to “1” (to enable
interrupts).
If the individual enable flags (EF) and interrupt latches (IL) are set under conditions other than the
above, the proper operation cannot be guaranteed.
88CS38B-21
2007-09-12
Digital noise reject circuit
···························
88CS38B-22
IL31 to 3 write data
Internal reset
Write
strobe
for IL
S
R
S
R
S
R
S
R
S
R
IL5
IL4
IL17
IL16
Q
Q
Q
Q
IL3 Q
Interrupt enable flag
EF31 to EF3
Vector table
address
Instruction which
clears IMF to “0”
R S
IMF
Q
Instruction which sets
IMF to “1”
[RETN] instruction only when
IMF was set before
interrupt was accepted
[EI] instruction
[RETI] instruction during
maskable interrupt
service
Interrupt master enable flag
Interrupt
acceptance
Vector
table
address
generator Non-maskable interrupts request
Interrupt request
Maskable
interrupts
Release IDLE mode
request
request
and
Priority
encoder
[DI] Instruction
························
External interrupts control register
EINTCR
INT0EN
Interrupt latch
S
IL2 Q
R
························
INTSLI
INTOSD
INTKOW
INTTC1
INT0
········
INTSW
········
INTWDT
···
IL17 to IL2
TMP88CS38B/CM38B/CP38B
Figure 1.5.1 Interrupt Controller Block Diagram
2007-09-12
TMP88CS38B/CM38B/CP38B
Interrupt latches (IL) that hold the interrupt requests are provided for interrupt sources.
Each interrupt vector is independent.
The interrupt latch is set to “1” when an interrupt request is generated, and requests the
CPU to accept the interrupt. The acceptance of maskable interrupts can be selectively enabled
and disabled by program using the interrupt master enable flag (IMF) and the individual
interrupt enable flags (EF). When two or more interrupts are generated simultaneously, the
interrupt is accepted in the highest priority order as determined by the hardware. Figure 1.5.1
shows the interrupt controller.
(1) Interrupt latches (IL31 to IL2)
Interrupt latches are provided for each source, except for a software interrupt. The latch
is set to “1” when an interrupt request is generated, and requests the CPU to accept the
interrupt. The latch is cleared to “0” just after the interrupt is accepted. All interrupt
latches are initialized to “0” during reset.
The interrupt latches are assigned to addresses 0003CH, 0003DH, 0002EH and 0002FH
in the SFR. Except for IL2, each latch can be cleared to “0” individually by an instruction ;
however, the read-modify-write instruction such as bit manipulation or operation
instructions cannot be used. When interrupt occurred during order execution, the reason is
because interrupt request is cleared. Thus, interrupt requests can be canceled and
initialized by the program. Note that request the interrupt latches cannot be set to “1” by
an instruction. For example, it may be that each latch is cleared even if an interrupt
request is generated during instruction exection.
The contents of interrupt latches can be read out by an instruction. Therefore, testing
interrupt request by software is possible.
Example 1: Clears interrupt latches
DI
LDW
(ILL), 1110100000111111B
;
Disable interrupt
;
IL12, IL10 to IL6 ← 0
;
W ← ILH, A ← ILL
;
if IL7 = 1 then jump
Example 2: Reads interrupt latches
LD
WA, (ILL)
Example 3: Tests an interrupt latch
TEST
(ILL). 7
JR
F, SSET
(2) Interrupt enable register (EIR)
The interrupt enable register (EIR) enables and disables the acceptance of interrupts,
except for the pseudo non-maskable interrupts (Software and watchdog timer interrupts).
Pseudo non-maskable interrupts are accepted regardless of the contents of the EIR;
however, the pseudo non-maskable interrupt cannot be nested more than once at the same
time.
The EIR consists of an interrupt master enable flag (IMF) and the individual interrupt
enable flags (EF). These registers are assigned to addresses 0003AH, 0003BH, 0002CH and
0002DH in the SFR, and can be read and written by an instruction (including
read-modify-write instruction such as bit manipulation instructions).
Note: Do not use the read-modify-write instruction for the EIRL (Address 0003AH) during
pseudo non-maskable interrupt service task. If the read-modify-write instruction is used,
the IMF is not set to “1” after RETN.
88CS38B-23
2007-09-12
TMP88CS38B/CM38B/CP38B
1.
Interrupt master enable flag (IMF)
The interrupt master enable flag (IMF) enables and disables the acceptance of all
maskable interrupts. Clearing this flag to “0” disables the acceptance of all maskable
interrupts. Setting to “1” enables the acceptance of interrupts.
When an interrupt is accepted, this flag is cleared to “0” to temporarily disable the
acceptance of other maskable interrupts. After execution of the interrupt service
program, this flag is set to “1” by the maskable interrupt return instruction [RETI] to
again enable the acceptance of interrupts. If an interrupt request has already been
occurred, interrupt service starts immediately after execution of the [RETI]
instruction.
Pseudo non-maskable interrupts are returned by the [RETN] instruction. In this
case, the IMF is set to “1” only when pseudo non-maskable interrupt service is started
with interrupt acceptance enabled (IMF = 1). Note that the IMF remains “0” when
cleared by the interrupt service program.
The IMF is assigned to bit0 at address 0003AH in the SFR, and can be read and
written by an instruction. The IMF is normally set and cleared by the [EI] and [DI]
instructions, and the IMF is initialized to “0” during reset.
2.
Individual interrupt enable flags (EF17 to EF3)
These flags enable and disable the acceptance of individual maskable interrupts,
except for an external interrupt 0. Setting the corresponding bit of an individual
interrupt enable flag to “1” enables acceptance of an interrupt, setting the bit to “0”
disables acceptance.
Example 1: Sets EF for individual interrupt enable, and sets IMF to “1”.
DI
LD
(EIRE), 00000001B
LDW
(EIRL), 1110100010100001B
;
Disable interrupt
;
EF16 ← 1
EF15 to EF13, EF11, EF7, EF5, IMF ← 1
Example 2: Sets an individual interrupt enable flag to “1”.
SET
(EIRH). 4
;
88CS38B-24
EF12 ← 1
2007-09-12
TMP88CS38B/CM38B/CP38B
Interrupt Latches (IL)
IL
(0002E,
0002FH)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
IL31
IL30
IL29
IL28
IL27
IL26
IL25
IL24
IL23
IL22
IL21
IL20
IL19
IL18
IL17
IL16
ILD (0002FH)
ILE (0002EH)
(Initial value: 00000000 00000000)
IL
(0003C,
0003DH)
IL15
IL14
IL13
IL12
IL11
IL10
IL9
IL8
IL7
IL6
IL5
IL4
ILH (0003DH)
IL3
IL2
INF
ILL (0003CH)
(Initial value: 00000000 00000000**)
Interrupt Enable Registers (EIR)
EIR
(0002C,
0002DH)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
EF31 EF30 EF29 EF28 EF27 EF26 EF25 EF24 EF23 EF22 EF21 EF20 EF19 EF18 EF17 EF16
EIRD (0002DH)
EIRE (0002CH)
(Initial value: 00000000 00000000)
EIR
(0003A,
0003BH)
EF15 EF14 EF13 EF12 EF11 EF10
EF9
EF8
EF7
EF6
EF5
EIRH (0003BH)
EF4
EF3
IMF
EIRL (0003AH)
(Initial value: 00000000 0000000**0)
Note 1:
Do not clear IL with read-modify-write instructions such as bit operations.
Note 2:
Do not set IMF to “1” during non-maskable interrupt service program.
Note 3:
Bits 1 and 0 in ILL are read in as undefined data when a read instruction is executed.
Note 4:
*: Don’t care
Note 5:
Do not clear IL2 to “0” by an instruction.
Note 6:
At TMP88CS38/CM38A/CP38A, IL18 to IL31 and EF18 to EF31 are not used.
Note 7:
After IMF is cleared, modify EF and IL.
Figure 1.5.2 Interrupt Latches (IL) and Interrupt Enable Registers (EIR)
1.5.1
Interrupt Sequence
An interrupt request is held until the interrupt is accepted or the interrupt latch is
cleared to “0” by a reset or an instruction. Interrupt acceptance sequence requires 12
machine cycles (3 μs at fc = 16 MHz in the NORMAL mode) after the completion of the
current instruction execution. The interrupt service task terminates upon execution of an
interrupt return instruction [RETI] (for maskable interrupts) or [RETN] (for pseudo
non-maskable interrupts). Figure 1.5.3 shows the timing chart of interrupt acceptance
processing.
(1) Interrupt acceptance
Interrupt acceptance processing is as follows.
1.
The interrupt master enable flag (IMF) is cleared to “0” to temporarily disable the
acceptance of any following maskable interrupts. When a non-maskable interrupt
is accepted, the acceptance of any following interrupts is temporarily disabled.
2.
The interrupt latch (IL) for the interrupt source accepted is cleared to “0”.
3.
The contents of the program counter (PC) and the program status word (PSW) are
saved (Pushed) on the stack in sequence of PSWH, PSWL, PCE, PCH, PCL. The
stack pointer (SP) is decremented five times.
4.
The entry address of the interrupt service program is read from the vector table,
and set to the program counter.
88CS38B-25
2007-09-12
TMP88CS38B/CM38B/CP38B
5.
The RBS control code is read from the vector table. The lower 4 bits of this code is
added to the RBS.
6.
The instruction stored at the entry address of the interrupt service program is
executed.
Example:
Correspondence between vector table address for INTTBT and the entry address of the interrupt
service program.
Entry address
Vector table address
FFFE4H
43H
FFFE5H
D2H
0CH
FFFE7H
06H
Vector
CD244H
CD245H
RBS
control
Interrupt
service
program
CD246H
··
FFFE6H
CD243H
A maskable interrupt is not accepted until the IMF is set to “1” even if the maskable
interrupt higher than the level of current servicing interrupt is occurred.
When nested interrupt service is necessary, the IMF is set to “1” in the interrupt
service program. In this case, acceptable interrupt sources are selectively enabled by
the individual interrupt enable flags.
Note:
Do not use the read-modify-write instruction for the EIRL (Address 0003AH) during
pseudo non-maskable interrupt service task.
88CS38B-26
2007-09-12
TMP88CS38B/CM38B/CP38B
Interrupt service task
1-machine cycle
INT5
INTTBT
IL15
IL6
IMF
Execution
Instruction
Address
bus
PC
Interrupt acceptance
a+1
a
FFFE4 FFFE5 FFFE6 FFFE7
a+1
a
n
Instruction
n−1 n−2 n−3 n−4
a
SP
b
n − 1 n −2 n − 3 n − 4
n
RBS
b
b+1 b+2
b+1 b+2 b+3
n−5
k = i + (FFFE7H). 3 − 0
i
INF
(a) Interrupt acceptance
Interrupt service task
IMF
RETI instruction
Execution
Address
bus
PC
SP
c
c
c+1 n−4 n−3 n−2 n−1
c+1
C+2
n−5
n−4 n−3 n−2 n−1
RBS
k
n
a+1
a
a
a+1 a+2
n
i
INF
(b) Return from interrupt instruction
Note 1:
a: Return address, b: Entry address, c: Address which the RETI instruction is stored
Note 2:
The maximum response time from when an IL is set until an interrupt acceptance processing starts is 62/fc
[s] with interrupt enabled.
Figure 1.5.3 Timing Chart of Interrupt Acceptance and Interrupt Return Instruction
88CS38B-27
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Saving/restoring general-purpose registers
During interrupt acceptance processing, the program counter (PC) and the program
status word (PSW) are automatically saved on the stack, but not the accumulator and
other registers. These registers are saved by the program if necessary. Also, when
nesting multiple interrupt services, it is necessary to avoid using the same data
memory area for saving registers.
The following method is used to save/restore the general-purpose registers.
1.
General-purpose register save/restore by automatic register bank changeover
The general-purpose registers can be saved at high speed by switching to a
register bank that is not in use. Normally, the bank0 is used for the main task and
the banks 1 to 15 are assigned to interrupt service tasks. To increase the efficiency
of data memory utilization, the same bank is assigned for interrupt sources which
are not nested.
The switched bank is automatically restored by executing an interrupt return
instruction [RETI] or [RETN]. Therefore, it is not necessary for a program to save
the RBS.
Example: Register bank changeover
PINTxx:
Interrupt processing
RETI
····
VINTxx:
2.
DP
PINTxx
DB
1
;
RBS ← RBS + 1
General-purpose register save/restore by register bank changeover
The general-purpose registers can be saved at high speed by switching to a
register bank that is not in use. Normally, the bank0 is used for the main tank and
the banks 1 to 15 are assigned to interrupt service tasks.
Example: Register bank changeover
PINTxx:
LD RBS, n
Interrupt processing
RETI
Restores bank and returns
;
Interrupt service routine entry address
····
;
VINTxx:
Main task
Bank m
Acceptance
of interrupt
Interrupt
service task
DP
PINTxx
DB
0
Switch to bank n by
LD, RBS and n
instruction
Main task
m
Acceptance
of interrupt
Interrupt
service task
m
n
Time
m
Interrupt return
Saving
registers
Switch to bank n
automatically
Restore to bank m
automatically by
[RETI]/[RETN]
Restoring
registers
Interrupt return
(a) Saving/restoring by register bank changeover
(b) Saving/restoring using push/pop or data transfer instructions
Figure 1.5.4 Saving/Restoring General-purpose Registers
88CS38B-28
2007-09-12
TMP88CS38B/CM38B/CP38B
3.
General-purpose registers save/restore using push and pop instructions
To save only a specific register, and when the same interrupt source occurs more
than once, the general-purpose registers can be saved/restored using the push/pop
instructions.
Example: Register save/restore using push and pop instructions
PINTxx:
PUSH
WA
;
Save WA register pair
;
Restore WA register pair
;
Return
Interrupt processing
POP
WA
RETI
Address (Example)
SP
0023AH
A
SP
0023B
W
SP
0023C
PCL
PCL
PCL
0023D
PCH
PCH
PCH
0023E
PCE
PCE
PCE
0023F
PSWL
PSWL
PSWL
00240
PSWH
PSWH
PSWH
At acceptance
of an interrupt
4.
At execution
of a push
instruction
SP
At execution
of a pop
instruction
00241
At execution of an
interrupt return
instruction
General-purpose registers save/restore using data transfer instructions
Data transfer instruction can be used to save only a specific general-purpose
register during processing of single interrupt.
Example: Saving/restoring a register using data transfer instructions
PINTxx:
LD
(GSAVA), A
;
Save A register
Interrupt processing
LD
A, (GSAVA)
RETI
88CS38B-29
;
Restore A register
;
Return
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) Interrupt return
The interrupt return instructions [RETI]/[RETN] perform the following operations.
[RETI] Maskable Interrupt Return
[RETN] Non-maskable Interrupt Return
1. The contents of the program counter and 1. The contents of the program counter and program status
the program status word are restored
word are restored from the stack.
from the stack.
2. The stack pointer is incremented 5 times. 2. The stack pointer is incremented 5 times.
3. The interrupt master enable flag is set to
“1”.
3. The interrupt master enable flag is set to “1” only when a
non-maskable interrupt is accepted in interrupt enable status.
However, the interrupt master enable flag remains at “0”
when so clear by an interrupt service program.
4. The interrupt nesting counter is
decremented, and the interrupt nesting
flag is changed.
4. The interrupt nesting counter is decremented, and the
interrupt nesting flag is changed.
Interrupt requests are sampled during the final cycle of the instruction being
executed. Thus, the next interrupt can be accepted immediately after the interrupt
return instruction is executed.
Note:
1.5.2
When the interrupt processing time is longer than the interrupt request generation
time, the interrupt service task is performed but not the main task.
Software Interrupt (INTSW)
Executing the [SWI] instruction generates a software interrupt and immediately starts
interrupt processing (INTSW is highest prioritized interrupt). However, if processing of a
non-maskable interrupt is already underway, executing the SWI instruction will not
generate a software interrupt but will result in the same operation as the [NOP]
instruction.
Use the [SWI] instruction only for detection of the address error or for debugging.
1.
Address error detection
FFH is read if for some cause such as noise the CPU attempts to fetch an instruction
from a non-existent memory address. Code FFH is the SWI instruction, so a software
interrupt is generated and an address error is detected. The address error detection
range can be further expanded by writing FFH to unused areas of the program memory.
Address-trap reset is generated in case that an instruction is fetched from RAM, SFR
or DBR areas.
2.
Debugging
Debugging efficiency can be increased by placing the SWI instruction at the software
break point setting address.
1.5.3
External Interrupts
The TMP88CS38B/CM38B/CP38B each have five external interrupt inputs ( INT0 , INT2,
INT3, INT4 and INT5 ). Three of these are equipped with digital noise rejection circuits
(Pulse inputs of less than a certain time are eliminated as noise). Edge selection is also
possible with INT2, INT3 and INT4.
The INT0 /P50 pin can be configured as either an external interrupt input pin or an
input/output port, and is configured as an input port during reset.
Edge selection, noise rejection control except INT3 pin input and INT0 /P50 pin function
selection are performed by the external interrupt control register (EINTCR). Edge selecting
and noise rejection control for INT3 pin input are preformed by the remote control signal
preprocessor control registers. (Refer to the section of the remote control signal
preprocessor.) When INT0EN = 0, the IL3 will not be set even if the falling edge of INT0
pin input is detected.
88CS38B-30
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 1.5.2 External Interrupts
Source
INT0
Pin
Secondary
Function Pin
Enable Conditions
Edge
Digital Noise Rejection
IMF = 1, INT0EN = 1, EF3 = 1
Falling edge
Any pulse shorter than 2/fc [s]
is regarded as noise and
removed. Pulses not shorter
than 7/fc [s] are definitely
regarded as signals.
Pulses of less than 7/fc [s] are
eliminated as noise. Pulses
equal to or more than 25/fc [s]
are regarded as signals.
INT0
P50/TC2/ PWM8
INT2
INT2
P53/TC1/ SCK1 /
AIN0/ KWU0
IMF·EF7 = 1
Falling edge or
rising edge
INT3
INT3
P30/RXIN
IMF·EF11 = 1
Falling edge,
rising edge or
falling/rising edge
Refer to the section of the
remote control preprocessor
INT4
INT4
P31/TC3
IMF·EF12 = 1
Falling edge or
rising edge
Pulses of less than 7/fc [s] are
eliminated as noise. Pulses of
25/fc [s] or more are
considered to be signals.
Falling edge
Any pulse shorter than 2/fc [s]
is regarded as noise and
removed. Pulses not shorter
than 7/fc [s] are definitely
regarded as signals.
INT5
INT5
P20/ STOP
IMF·EF15 = 1
Note 1: The noise rejection function is also affected for timer counter input 1 (TC1 pin).
Note 2: If a noiseless signal is input to the external interrupt pin in the NORMAL or IDLE mode, the maximum
time from the edge of input signal until the IL is set is as follows:
(1) INT2, INT4 pin 31/fc [s]
(2) INT3 pin
Refer to the section of the remote control preprocessor.
Note 3: If a dual-function pin is used as an output port, changing data or switching between input and output
generates a pseudo interrupt request signal. To ignore this signal, it is necessary to reset the interrupt
enable flag.
Note 4: If INT0EN = “0”, detecting the falling edge of the INT0 pin input does not set the interrupt latch IL3.
88CS38B-31
2007-09-12
TMP88CS38B/CM38B/CP38B
EINTCR
(00037H)
7
6
INT0
EN
“0”
INT0EN
INT4ES
INT2ES
Note 1:
5
−
4
INT4
ES
P50/ INT0 pin configuration
INT4 and INT2 edge select
3
−
2
INT2
ES
1
0
“0”
−
(Initial value: 00*0 *00*)
0: P50 input/output port
1: INT0 pin (Port P50 should be set to an input mode)
Write
only
0: Rising edge
1: Falling edge
fc: High-frequency clock [Hz], *: Don’t care
Note 2:
Edge detection during switching edge selection is invalid.
Note 3:
Do not change EINTCR only when IMF = 1. After changing EINTCR, interrupt latches of external interrupt
inputs must be cleared to “0” using load instruction.
Note 4:
In order to change of external interrupt input by rewriting the contents of INT2ES and INT4ES during
NORMAL mode, clear interrupt latches of external interrupt inputs (INT2 and INT4) after 8 machine cycles
from the time of rewriting.
Note 5:
In order to change an edge of timer counter input by rewritng the contents of INT2ES during NORMAL
mode, rewrite the contents after timer counter is stopped (TC*s = 0) , that is, terrupt disable state.
Then, clear a interrupt latch of external interrupt input (INT2) after 8 machine cycles from the time of
rewriting to change to interrupt enable state. Finally, start timer counter.
Example:
When change TC1 pin inputs edge in external trigger timer mode from rising edge falling edge.
LD (TC1CR) , 01001000B
;
TC1S ← 00 (Stops TC1)
DI
;
IMF ← 0 (Disables interrupt service)
LD (EINTCR) , 00000100B
;
INT2ES ← 1 (Change edge selection)
NOP
to
8-machine
NOP
cycles
LD (ILL) , 01111111B
;
IL7 ← 0 (Clears interrupt latch)
EI
;
IMF ← 1 (Enable interrupt service)
LD (TC1CR) , 01111000B
;
TC1S ← 11 (Starts TC1)
Figure 1.5.5 External Interrupt Control Register
88CS38B-32
2007-09-12
TMP88CS38B/CM38B/CP38B
1.6
Reset Circuit
The TMP88CS38B/CM38B/CP38B has four types of reset generation procedures: An external
reset input, an address trap reset output, a watchdog timer reset output and a system clock
reset output. Table 1.6.1 shows on-chip hardware initialization by reset action.
The malfunction reset output circuit such as watchdog timer reset, address trap reset and
system clock reset is not initialized when power is turned on. The RESET pin can output level
“L” at the maximum 24/fc [s] (1.5 μs at 16 MHz) when power is turned on.
Table 1.6.1 Initializing Internal Status by Reset Action
On-chip Hardware
Initial Value
Program counter
(PC)
(FFFFEH to FFFFCH)
Stack pointer
(SP)
Not initialized
General-purpose registers
(W, A, B, C, D, E, H, L)
Not initialized
Register bank selector
(RBS)
0
(JF)
1
Zero flag
(ZF)
Not initialized
Carry flag
(CF)
Not initialized
Half carry flag
(HF)
Not initialized
Sign flag
(SF)
Not initialized
Overflow flag
(VF)
Not initialized
(IMF)
0
Jump status flag
Interrupt master enable flag
Interrupt individual enable flags
1.6.1
−
Enable
Refer to I/O port
circuitry
Control registers
Refer to each of
control register
RAM
Not initialized
0
−
0
Output latches of I/O ports
0
(IL)
Initial Value
Prescaler and divider of timing
generator
Watchdog timer
(EF)
Interrupt latches
On-chip Hardware
External Reset Input
The RESET pin contains a Schmitt trigger (Hysteresis) with an internal pull-up resistor.
When the RESET pin is held at “L” level for at least 3 machine cycles (12/fc [s]) with the
power supply voltage within the operating voltage range and oscillation stable, a reset is
applied and the internal state is initialized.
When the RESET pin input goes high, the reset operation is released and the program
execution starts at the vector address stored at addresses FFFFCH to FFFFEH.
VDD
Reset input
RESET
Watchdog timer reset
Sink open drain
Malfunction
reset output
circuit
Address trap reset
System clock reset
Figure 1.6.1 Reset Circuit
88CS38B-33
2007-09-12
TMP88CS38B/CM38B/CP38B
1.6.2
Address-trap-reset
If the CPU should start looping for some cause such as noise and an attempt be made to
fetch an instruction from the on-chip RAM, DBR or the SFR area, address-trap-reset will
be generated. Then, the RESET pin output will go low. The reset time is about 8/fc to 24/fc
[s] (0.5 to 1.5 μs at 16 MHz).
Instruction
execution
JP
a
Reset release
Address trap is occurred
(“L” output)
RESET output
8/fc to 24/fc [s]
Note 1:
Instruction at address
(High-Z)
4/fc
to
12/fc [s]
20/fc [s]
(No wait)
0 ≤ a ≤ 008BFH (TMP88CS38B), 0 ≤ a ≤ 006BFH (TMP88CM38B/CP38B)
0 ≤ a ≤ 002BFH (The ROM corrective function is enabled.)
Note 2:
During reset release, reset vector “r” is read out, and an instruction at address “r” is fetched and decoded.
Figure 1.6.2 Address-trap-reset
1.6.3
Watchdog Timer Reset
Refer to section 2.4 “Watchdog Timer”.
1.6.4
System-clock-reset
Clearing bits 7 in SYSCR2 to “0”, system clock stops and causes the microcomputer to
deadlock. This can be prevented by automatically generating a reset signal whenever bits 7,
6 and 5 in SYSCR2 = 000 is detected to continue the oscillation. The RESET pin output
goes low from high-impedance. The reset time is about 8/fc to 24/fc [s] (0.5 to 1.5 μs at 16
MHz).
88CS38B-34
2007-09-12
TMP88CS38B/CM38B/CP38B
1.7
ROM Corrective Function
The ROM corrective function can patch the part (s) of on-chip ROM with some bugs.
The ROM corrective function have two modes. One is to replaced the instruction on a certain
address in the ROM with the jump instruction to branch into the RAM area where the patched
codes (Program jump mode). The other is to replace a byte or a word (2 or 3 bytes) length data in
the ROM with the patched data (Data replacement mode). Four independent location can be
patched.
Note 1: When use ROM corrective circuit, it is necessary to contain a program which operates to load
patched program and/or replacement data from external memory into an internal data RAM
in an initial routine.
Note 2: The address of a instruction for IDLE mode can not be specificated as start address of
corrective area.
Note 3: The BM88CS38N0A does not support the ROM corrective circuit. Use the TMP88PS38B to
debug a program of this circuit. In this case, note the following.
In program jump mode, jump target addresses that can be specified with the
TMP88CM38B/CP38B (002C0H to 006BFH) are different from those that can be specified
with the TMP88PS38B (002C0H to 008BFH). Therefore, if a jump target address is within a
range of 006C0H to 008BFH, it is necessary to change this addresse and also addresses for
loading a patch program.
Example:
ROM corrective circuit
ROMCDR
RAM
ROMCDR
Serial
bus
interface
88CS38B-35
• Correction mode
• Correction code
• Patch program
2007-09-12
TMP88CS38B/CM38B/CP38B
Match
signal
Address compare circuit
23
to
Register 6
selection
5
circuit
4
3
2
1
0
5
BANK3
Data bus
BANK2
Address bus
BANK1
Configuration
BANK0
1.7.1
Instruction fetch control circuit
to
to
the lower
the middle
the upper
the lower
Compare address register
the middle
the upper
Data register
CM CM CM CM
0
1
2
3
Corrective mode signal
Write data count
Register write signal
ROMCDR
WDC
CM3-0
ROM corrective
data register
Write data
count register
ROM corrective
control register
Figure 1.7.1 ROM Corrective Circuit
88CS38B-36
2007-09-12
TMP88CS38B/CM38B/CP38B
1.7.2
Control
The ROM corrective function is controlled by ROM corrective control register (ROMCCR)
and ROM corrective data register (ROMCDR).
ROM Corrective Control Register
ROMCCR
(00FE0H)
7
6
5
4
3
2
1
0
−
−
−
−
CM3
CM2
CM1
CM0
CM3
Corrective mode setting
(BANK3)
CM2
Corrective mode setting
(BANK2)
CM1
Corrective mode setting
(BANK1)
CM0
Corrective mode setting
(BANK0)
(Initial value: **** 0000)
0: Proguram jump mode
R/W
1: Data replacement mode
ROM Corrective Status Register
ROMCSR
(00FE1H)
7
6
5
−
−
−
WDC
Write data counter
4
3
2
WDC
1
0
(Initial value: ***0 0000)
Read
only
Counting the number of the byte written in ROMCDR
ROM Corrective Data Register
ROMCDR
(00FE2H)
7
6
5
4
3
2
1
0
(Initial value: 0000 0000)
ROMC
Write
only
ROM Corrective data register
Figure 1.7.2 ROM Corrective Control Register, Status Register and ROM Corrective Data Register
(1) Enable and disable
The ROM corrective function is disabled after releasing reset. It is enabled after
setting the data for one bank into ROMCDR. And the address-trap-reset is not
generated when fetching an instruction from the RAM area except the address 02C0H
to 08BFH.
After the ROM corrective function is enabled, it is necessary to reset the
microcontroller in order to disable it.
(2) Data replacement mode
The ROM corrective function has the program jump mode and the data replacement
mode.
By setting CMx (x: 0 to 3) in ROMCCR, the data replacement mode is selected.
(3) The ROM corrective data register writing
The ROM corrective data register has four banks corresponding to four independent
locations to patch. The write data counter (WDC) points each bank set. (Figure 1.7.2)
88CS38B-37
2007-09-12
TMP88CS38B/CM38B/CP38B
ROM Corrective Data Register
ROMCDR
(00FE2H) ROMC7 ROMC6 ROMC5 ROMC4 ROMC3 ROMC2 ROMC1 ROMC0
(Initial value: 0000 0000)
The value of WDC after writing a data to ROMCDR
00000 (Initial value)
BANK0
BANK1
BANK2
BANK3
The lower start address of the corrective area (8 bits)
00001
The middle start address of the corrective area (8 bits)
00010
The upper start address of the corrective area (4 bits)
00011
The lower 8 bits of the jump address/replacement data
00100
The middle 8 bits of the jump address/replacement data
00101
The upper 4 bits of the jump address/replacement data
00110
The lower start address of the corrective area (8 bits)
00111
The middle start address of the corrective area (8 bits)
01000
The upper start address of the corrective area (4 bits)
01001
The lower 8 bits of the jump address/replacement data
01010
The middle 8 bits of the jump address/replacement data
01011
The upper 4 bits of the jump address/replacement data
01100
The lower start address of the corrective area (8 bits)
01101
The middle start address of the corrective area (8 bits)
01110
The upper start address of the corrective area (4 bits)
01111
The lower 8 bits of the jump address/replacement data
10000
The middle 8 bits of the jump address/replacement data
10001
The upper 4 bits of the jump address/replacement data
10010
The lower start address of the corrective area (8 bits)
10011
The middle start address of the corrective area (8 bits)
10100
The upper start address of the corrective area (4 bits)
10101
The lower 8 bits of the jump address/replacement data
10110
The middle 8 bits of the jump address/replacement data
10111
The upper 4 bits of the jump address/replacement data
00000
Note 1:
Note 2:
WDC value equals to the number of the byte stored in ROMCDR.
ROMCDR is set in order of the lower (8 bits), the middle (8 bits) and the upper (4 bits) start address of the
corrective area, the lower (8 bits), the middle (8 bits) and the upper (4 bits) of the jump address/the
replacement data.
Figure 1.7.3 Banks and WDC Value of the Program Corrective Data Register
Whenever ROMCDR is written, WDC is incremented to indicate what data is writen via
ROMCDR. During reset, WDC is initialized to “0”.
(1) The lower start address of the corrective area (8 bits)
(2) The middle start address of the corrective area (8 bits)
(3) The upper start address of the corrective area (4 bits)
(4) The lower jump address/replacement data (8 bits)
(5) The middle jump address/replacement data (8 bits)
(6) The upper jump address (4 bits)/replacement data
Note 1: Corrective addresses must have over five addresses each other.
Note 2: The address of a instruction for IDLE mode can not be specificated as start address of
corrective area.
88CS38B-38
2007-09-12
TMP88CS38B/CM38B/CP38B
1.7.3
Functions
The ROM corrective function can correct maximum four ROM areas with their
corresponding four banks of ROM corrective registers. Either program jump mode or data
replacement mode is selected for each bank by CM0 to CM3 respectively.
(1) Program jump mode
In the program jump mode, the system executes a jump instruction when the
program execution reaches the instruction at the corrective ROM address, skips from
the instruction which would have been executed, and executes an instruction at a
preset jump address.
Clearing ROMCCR CMx (x: 0 to 3) to “0” puts the system in the program jump mode.
Use ROMCDR to set the corrective ROM address and jump address.
When the start address of an erroneous program is a corrective ROM address, and
that of the patch program is a jump address, the bug in the erroneous program can be
fixed. Note that the patch program should end with a jump instruction, which causes a
return to the built-in ROM.
Note:
For program jump mode, the address to be corrected must be the start address of
the instruction.
Example 1: Setting the program correction circuit with the initial routine
Using the initial routine program, which is executed right after reset, set the
program correction circuit's register and stores the patch program into the built-in
RAM as follows.
1.
Read the flag, which indicates whether to use the program correction circuit, from
the external memory.
2.
If that circuit is not used, perform normal initial processing.
3.
If it is used, clear CMx to 0 to establish the program jump mode.
4.
Read the corrective ROM address and jump address from the external memory.
5.
Set the corrective ROM address and jump address, which were read in step “4.”, in
ROMCDR.
6.
Read the number of bytes for the patch program from the external memory.
7.
Read the program with a number of bytes, equal to the byte count read in step “6.”,
from the external memory, and store that program into the built-in RAM.
8.
Repeat steps “4.” through “7.” as many times as there are required banks.
Example 2: There is bugs on the locations from 0C020H to 0C085H
The corrective address, the jump vector, the program patch codes and other
information to patch the ROM with the bugs must be read out from any of memory
storage that holds them during initial program routine. CMn = 0 specifies the
program jump mode. Subsequently, the patch program codes are loaded into RAM
(00600H to 006EFH). The start address (0C020H) of the ROM necessary to patch
is written to the corrective ROM address registers, and the start address (00600H)
of the RAM area to patch is loaded onto the jump address registers. When the
instruction at 0C020H is fetched, the instruction to jump into 00600H is
unconditionally executed instead of the instruction at 0C020H, and the
subsequent patch program codes are executed. The jump instruction at the end of
the patch program codes returns to the ROM at 0C086H.
88CS38B-39
2007-09-12
TMP88CS38B/CM38B/CP38B
00000H
SFR
0003FH
00040H
00600H
Patch
program
RAM
0083FH
JP 0C086H
006EFH
006F0H
00F80H
DBR
00FFFH
Return
04000H
ROM
0C020H
0C085H
Bug area
0C086H
FFFFFH
Note:
Corrective address must be assigned to 1st byte of instruction codes on the
program jump mode.
(2) Data replacement mode
In the data replacement mode, the system replaces reference data stored in the ROM
area with the new instead of correcting the data reference instruction when that
reference data is changed.
The program jump mode reduces the complexity of correcting the processing routine.
However, when this mode is used, if there is a need to replace only the fixed data in
ROM, the instruction to reference this ROM data should be corrected. Thus, a large
amount of ROM is required for the patch program. To avoid this, the system has the
data replacement mode. With this mode, three consecutive bytes of data can be
replaced for each bank. (For an instruction which accesses only one byte, only the first
byte can be replaced. For an instruction which accesses only two bytes, the two
consecutive bytes can be replaced.) Setting ROMCCR CMx (x: 0 to 3) to “1” puts the
system in the data replacement mode. Specify the start address of ROM data to be
replaced as the corrective ROM address. Then, specify the new three-byte data as the
patch data.
Note:
For data replacement mode, the corrective address should be the address of fixed
data (including a vector). (The operation code and operand cannot be changed.)
Example 1: Setting the program correction circuit with the initial routine
Using the initial routine program, which is executed right after reset, set the
program correction circuit's register as follows.
1.
Read the flag, which indicates whether to use the program correction circuit, from
the external memory.
2.
If that circuit is not used, perform normal initial processing.
3.
If it is used, set CMx to “1” to establish the data replacement mode.
4.
Read the address of the data to be replaced and the patch data from the external
memory.
5.
Set the address and patch data, which were read in step “4.”, in ROMCDR.
6.
Repeat steps “4.” and “5.” as many times as there are required banks.
88CS38B-40
2007-09-12
TMP88CS38B/CM38B/CP38B
Example 2: Replacing data 55H at 0C020H with 33H
Using the initial routine program, which is executed right after reset, read the
start address of the data to be replaced and the patch data from the external
memory. Set CMx (x: 0 to 3) to “1” to change the correction mode to the data
replacement mode. Specify the start address (0C020H) of the data to be replaced
as the corrective ROM address. Then, specify the new three-byte data (33H for
0C020H, CCH for 0C021H, and C3H for 0C022H) as the patch data.
00000H
SFR
0003FH
00040H
RAM
0083FH
00F80H
DBR
00FFFH
04000H
ROM
0C020H
55H
33H
0C021H
AAH
CCH
0C022H
A5H
3CH
Replacement data
FFFFFH
1.
2.
3.
4.
At HL = 0C020H, Executing LD A, (HL) loads 33H in A. (Data replacement)
At HL = 0C021H, Executing LD A, (HL) loads AAH in A. (No data replacement)
At HL = 0C020H, Executing LD WA, (HL) loads CC33H in WA. (Data replacement)
At HL = 0C020H, Executing LD IX, (HL) loads CCC33H in IX. (Data replacement)
Note 1: Corrective address must be assigned to constant data area on the data
replacement mode. (Ope-code and ope-rand can’t be replaced by ROM correction
circuit.)
Note 2: Instructions which includes “(HL+)” or “(−HL) ” operation can't be replaced by ROM
corrective circuit on the data replacement mode.
88CS38B-41
2007-09-12
TMP88CS38B/CM38B/CP38B
2.
On-chip Peripheral Functions
2.1
Special Function Registers (SFR) and Data Buffer Registers (DBR)
The TLCS-870/X series uses the memory mapped I/O system and all peripheral control and
data transfers are performed through the special function registers (SFRs) and data buffer
registers (DBR).
The SFR are mapped to addresses 00000H to 0003FH, and DBR are mapped to address
00F80H to 00FFFH.
Figure 2.1.1 shows the list of the TMP88CS38B/CM38B/CP38B SFRs and-DBRs.
Address
00000H
00001
00002
00003
00004
00005
00006
00007
00008
00009
0000A
0000B
0000C
0000D
0000E
0000F
00010
00011
00012
00013
00014
00015
00016
00017
00018
00019
0001A
0001B
0001C
0001D
0001E
0001F
Read
Write
Reserved
Reserved
P2 port
P3 port
P4 port
P5 port
P6 port
P7 port
−
P5CR1 (P5 port I/O control1)
−
P7CR (P7 port I/O control)
Reserved
Reserved
−
P4CR (P4 port I/O control)
−
P6CR (P6 port I/O control)
ADCCRA (AD converter control A)
ADCCRB (AD converter control B)
TC1DRAL
(Timer register 1A)
TC1DRAH
TC1DRBL
−
(Timer register 1B)
−
TC1DRBH
TC1CR (TC1 control)
−
TC2CR (TC2 control)
−
TC2DRL
−
TC2DRH
(Timer register 2)
TC3DRA (Timer register 3A)
−
TC3DRB (Timer register 3B)
−
TC3CR (TC3 control)
−
TC4DR (Timer register 4)
−
TC4CR (TC4 control)
ORDSN (OSD control)
ORCRAL (OSD control)
ORCRAH (OSD control)
Address
00020H
00021
00022
00023
00024
00025
00026
00027
00028
00029
0002A
0002B
0002C
0002D
0002E
0002F
00030
00031
00032
00033
00034
00035
00036
00037
00038
00039
0003A
0003B
0003C
0003D
0003E
0003F
Read
Write
SBISRA (SBI statusA)
SBICRA (SBI control register A)
SBIDBR (SBI data buffer)
−
I2CAR (I2C bus address)
SBISRB (SBI statusB)
SBICRB (SBI control register B)
−
ORDMAL (OSD control)
−
ORDMAH (OSD control)
RCSR (TC3 status)
RCCR (TC3 control)
PMPXCR (Port control)
−
PWMCR1A (PWM control 1A)
−
PWMCR1B (PWM control 1B)
−
PWMDBR1 (PWMDBR1)
−
P3CR1 (P3 I/O control)
EIRE
(Interrupt enable register)
EIRD
ILE
(Interrupt latch)
ILD
CGCR (Divider control)
ADCDR1 (AD conversion result)
ADCDR2 (AD conversion result)
Reserved
−
WDTCR1
−
WDTCR2
Watchdog timer
control
TBTCR (TBT/TG control)
−
EINTCR (External interrupt control)
SYSCR1
(System control)
SYSCR2
EIRL
(Interrupt enable register)
EIRH
ILL
(Interrupt latch)
ILH
PSWL
(Program status word)
PSW H
(a) Special function registers
Note 1:
Do not access reserved areas by the program.
Note 2:
−: Cannot be accessed.
Note 3:
Write-only registers and interrupt latches cannot use the read-modify-write instructions (Bit manipulation
instructions such as SET, CLR, etc. and logical operation instructions such as AND, OR, etc.).
Note 4:
When defining address 0003FH with assembler symbols, use GRBS.
Address 0003EH must be GPSW/GFLAG.
Figure 2.1.1 (a) SFR
88CS38B-42
2007-09-12
TMP88CS38B/CM38B/CP38B
Address
00F80H
81
Read
Write
ORDON (OSD control)
−
OSD control register
−
A1
A2
OSD control register
Reserved
−
OSD control register
−
B9
BA
OSD control register
ORIRC (OSD display counter)
ORIRC (OSD interrupt control)
−
OSD control register
−
OSD control register
C0
Reserved
Reserved
D0
D1
IDLEINV (Key-on wakeup status)
IDLECR (Key-on wakeup control)
Reserved
Reserved
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
SINTCR (Data slicer interrupt control)
−
DACLCR (Sync. tip slice level setting)
SLVLCR (Slice level control)
SIFDR1 (Caption data 1st byte)
−
SIFDR2 (Caption data 2nd byte)
−
−
SIFSR (Data slicer status)
−
−
SIFS1R (Data slicer status2)
SIFSMS1 (Data slicer mode setting)
ROMCCR (ROM corrective control)
−
ROMCSR (ROM corrective status)
−
ROMCDR (ROM corrective data)
Reserved
JECR (Jitter elimination control)
−
JESR (Jitter elimination status)
−
TVSCR (Test video signal output)
Reserved
RXCR1 (Remote control recieve control 2)
RXCR2 (Remote control recieve control 1)
RXCTR (Remote control receive counter)
−
RXDBR (Remote control receive data buffer)
−
RXSR (Remote control status)
−
Reserved
FC8CR (FC8 control)
Reserved
Reserved
SCCRB (Serial clock source control)
SCSR (Serial clock source status)
Reserved
Reserved
Reserved
−
PWMCR2A (PWM control 2A)
−
PWMCR2B (PWM control 2B)
−
PWMDBR2 (PWM data buffer)
Reserved
Reserved
FE
FF
−
PSELCR (P3, P5 control 2)
Reserved
(b) Data buffer registers
Note 1:
Do not access reserved areas by the program.
Note 2:
−: Cannot be accessed.
Note 3:
Write-only registers cannot use the read-modify-write instructions (Bit manipulation instructions such as
SET, CLR, etc. and logical operation instructions such as AND, OR, etc.).
Figure 2.1.2 (b) DBR
88CS38B-43
2007-09-12
TMP88CS38B/CM38B/CP38B
2.2
I/O Ports
The TMP88CS38B/CM38B/CP38B has 6 parallel input/output ports (33 pins) as follows:
Primary Function
Secondary Functions
Port P2
1-bit I/O port
External interrupt input, and STOP mode release signal input
Port P3
6-bit I/O port
External interrupt input, remote control signal input, data slicer analog
input, timer/counter input, serial bus interface input/output and data
slicer input
Port P4
8-bit I/O port
Pulse width modulation output
Port P5
8-bit I/O port
Pulse width modulation output external interrupt input, timer/counter
input, key-on wakeup input, serial bus interface input/output, analog
input and I output from OSD circuitry.
Port P6
8-bit I/O port
R, G, B and Y/BL output from OSD circuitry, R.G.B and Y/BL input,
analog input, test video signal output and key-on wakeup input
Port P7
2-bit I/O port
Horizontal synchronous pulse input and vertical synchronous pulse
input to OSD circuitry
Each output port contains a latch, which holds the output data. All input ports do not have
latches, so the external input data should either be held externally until read or reading should
be performed several times before processing. Figure 2.2.1 shows input/output timing examples.
External data is read from an I/O port in the S1 state of the read cycle during execution of the
read instruction. This timing can not be recognized from outside, so that transient input such as
chattering must be processed by the program. Output data changes in the S2 state of the write
cycle during execution of the instruction which writes to an I/O port.
Fetch cycle
Instruction
execution
cycle
Fetch cycle
Read cycle
S0 S1 S2 S3 S0 S1 S2 S3 S0 S1 S2 S3
Ex.: LD
A, (x)
Input strobe
Data input
(a) Input timing
Fetch cycle
Instruction
execution
cycle
Fetch cycle
Write cycle
S0 S1 S2 S3 S0 S1 S2 S3 S0 S1 S2 S3
Ex.: LD
(x), A
Output latch
pulse
Data output
(b) Output timing
Note: The positions of the read and write cycles may vary, dispending on the instruction.
Figure 2.2.1 Input/Output Timing (Example)
88CS38B-44
2007-09-12
TMP88CS38B/CM38B/CP38B
When reading an I/O port except programmable I/O ports, whether the pin input data or the
output latch contents are read depends on the instructions, as shown below:
(1) Instructions that read the output latch contents
1. XCH r, (src)
2. SET/CLR/CPL (src).b
3. SET/CLR/CPL (pp).g
4. LD (src).b, CF
5. LD (pp).b, CF
6. ADD/ADDC/SUB/SUBB/AND/OR/XOR (src), n
7. (src) side of ADD/ADDC/SUB/SUBB/AND/OR/XOR (src), (HL)
(2) Instructions that read the pin input data
1. Instructions other than the above (1)
2. (HL) side of ADD/ADDC/SUB/SUBB/AND/OR/XOR (src), (HL)
2.2.1
Port P2 (P20)
Port P2 is a 1bit input/output port. It is also used as an external interrupt input, and a
STOP mode release signal input. When used as an input port, or a secondary function pin,
the output latch should be set to “1”. During reset, the output latch is initialized to “1”.
It is recommended that pin P20 should be used as an external interrupt input, a STOP
mode release signal input, or an input port. If used as an output port, the interrupt latch is
set on the falling edge of the P20 output pulse.
When a read instruction for port P2 is executed, bits 7 to 1 in P2 are read in as undefined
data.
SET/CLR/CPI/others
Output latch
D
Data input
P20 ( INT5 / STOP )
Q
Data input
Control input
STOP
OUTEN
7
P2
(00002H)
6
5
4
3
2
1
0
P20
INT5
STOP
(Initial value: **** ***1)
*: Don’t care
Figure 2.2.2 Port P2
88CS38B-45
2007-09-12
TMP88CS38B/CM38B/CP38B
2.2.2
Port P3 (P35 to P30)
Port P3 is an 6-bit input/output port which can be configured as an input or an output in
one-bit unit under software control. Input/output mode is specified by the corresponding bit
in the port P3 input/output control register 1 (P3CR1). Port P3 is configured as an input if
its corresponding P3CR1 bit is cleared to “0”, and as an output if its corresponding P3CR1
bit is set to “1”. During reset, P3CR1 is initialized to “0”, which configures port P3 as an
input. The P3 output latches are also initialized to “1”. Data is written into the output latch
regardless of the P3CR1 contents. Therefore initial output data should be written into the
output latch before setting P3CR1.
Port P3 is also used as an external interrupt input, remote-control signal input a
timer/counter input, data slicer input and serial bus interface input/output. When used as a
secondary function input pin except I2C bus interface input/output, the input pins should
be set to the input mode. When used as a secondary function output pin except I2C bus
interface input/output, the output pins should be set to the output mode and beforehand
the output latch should be set to “1”. When P34 and P35 are used as I2C bus interface
input/output, P3CR2 bits should be set to the sink open-drain mode, the output latches
should be set to “1”, and the output pins should be set to the output mode.
Note: Input mode port is read the state of input pin. When input/output mode is used mixed,
the contents of output latch setting input mode may be changed by executing bit
manipulation instructions.
Example 1: Outputs an immediate data 5AH to port P3
LD
(P3), 5AH
;
P3 ← 5AH
Example 2: Inverts the output of the lower 4 bits (P33 to P30) in port P3
XOR
(P3), 00001111B
;
88CS38B-46
P33 to P30 ← P33 to P30
2007-09-12
TMP88CS38B/CM38B/CP38B
STOP
OUTEN
STOP
OUTEN
P3iCR1
P3jCR1
Data input
Data input
Control input
Control input (*1)
P3iCR2
Data output
D
Q
D
Data output
Q
P3j
P3i
Control output
Output latch
Output latch
VIN (*2)
(a) P35 to P34
7
6
P3
(00003H)
P3CR1
7
5
P35
SDA0
4
P34
SCL0
3
P33
VIN0
TC4
2
P32
VIN1
CSIN
1
P31
INT4
TC3
0
P30
INT3
RXIN
5
4
3
2
1
0
6
(0002BH)
(b) P33 to P30
P35CR1 P34CR1 P33CR1 P32CR1 P31CR1 P30CR1
P3CR1
7
6
(0FFEH)
“0”
“0”
P3CR2
5
(Initial value: **00 0000)
0: Input mode
I/O control for P3
PSELCR
(Initial value: **11 1111)
Write
only
1: Output mode
4
P35CR2 P34CR2
I/O control for P3
3
2
“0”
1
P52CR2 P51CR2
0
“0”
(Initial value: 0*00 *00*)
0: Sink open drain
Write
only
1: Tri-state
(*1) only P33, P31, P30
(*2) only P33, P32
Note 1:
*: Don’t care, i = 5 to 4, j = 3 to 0
Note 2:
P3CR1 cannot used the read-modify-write instructions.
(Bit manipulation instructions such as SET, CLR, etc. and logical operation such as AND, OR, etc.)
Note 3:
Clear bit7, 6, 3 and 0 to “0” in PSELCR.
Figure 2.2.3 Port P3 and P3CR
88CS38B-47
2007-09-12
TMP88CS38B/CM38B/CP38B
2.2.3
Port P4 (P47 to P40)
Port P4 is an 8-bit input/output port which can be configured as an input or an output in
one-bit unit under software control. Input/output mode is specified by the corresponding bit
in the port P4 input/output control register (P4CR). Port P4 is configured as an input if its
corresponding P4CR bit is cleared to “0”, and as an output if its corresponding P4CR bit is
set to “1”. During reset, P4CR is initialized to “0”, which configures port P4 as an input. The
P4 output latches are also initialized to “1”. Data is written into the output latch regardless
of the P4CR contents. Therefore initial output data should be written into the output latch
before setting P4CR.
Port P4 is also used as a pulse width modulation (PWM) output. When used as a PWM
output pin, the output pins should be set to the output mode and beforehand the output
latch should be set to “1”.
Note: Input mode port is read the state of input pin. When input/output mode is used mixed,
the contents of output latch setting input mode may be changed by executing bit
manipulation instructions.
STOP
OUTEN
P4iCR
Data input
D
Data output
Q
P4i
Output latch
PWMi
P4
(00004H)
P4CR
(0000CH)
7
P47
6
P46
5
P45
4
P44
3
P43
2
P42
1
P41
P40
0
PWM7
PWM6
PWM5
PWM 4
PWM3
PWM2
PWM1
PWM0
7
6
5
4
3
2
1
0
P47CR
P46CR
P45CR
P44CR
P43CR
P42CR
P41CR
P40CR
P4CR
Note 1:
Note 2:
I/O Control for port P4
(Initial value: 1111 1111)
(Initial value: 0000 0000)
0: Input mode
Write
only
1: Output mode
i = 7 to 0.
P4CR cannot used the read-modify-write instructions.
(Bit manipulation instructions such as SET, CLR, etc. and logical operation such as AND, OR, etc.)
Figure 2.2.4 Port P4 and P4CR
88CS38B-48
2007-09-12
TMP88CS38B/CM38B/CP38B
2.2.4
Port P5 (P57 to P50)
Port P5 is an 8-bit input/output port which can be configured as an input or an output in
one-bit unit under software control. Input/output mode is specified by the corresponding bit
in the port P5 input/output control register 1 (P5CR1). Port P5 is configured as an input if
its corresponding P5CR1 bit is cleared to “0”, and as an output if its corresponding P5CR1
bit is set to “1”. During reset, P5CR1 is initialized to “0”, which configures port P5 as an
input. The P5 output latches are also initialized to “1”. Data is written into the output latch
regardless of the P5CR1 contents. Therefore initial output data should be written into the
output latch before setting P5CR1.
Port P5 is also used as is also used as AD converter analog input, a pulse width
modulation (PWM) output external interrupt input, timer/counter input, serial bus
interface input/output, and an on screen display (OSD) output (I signal). When used as a
secondary function input pin except I2C bus interface input/output, the input pins should
be set to the input mode. When used as a secondary function output pin except I2C bus
interface input/output, the output pins should be set to the output mode and beforehand
the output latch should be set to “1”. When P52 and P51 are used as I2C bus interface
input/output, P5CR2 bits should be set to the sink open-drain mode, the output latches
should be set to “1”, and the output pins should be set to the output mode. When P57 is used
as an OSD output pin, the output pin should be set to the output mode and beforehand the
port 6 data selection register (PIDS) should be clear to “0”. When used as port P5, the port 6
data selection register (PIDS) should be set to “1”.
Note: Input mode port is read the state of input pin. When input/output mode is used mixed,
the contents of output latch setting input mode may be changed by executing bit
manipulation instructions.
88CS38B-49
2007-09-12
TMP88CS38B/CM38B/CP38B
STOP
OUTEN
Analog input
AINDS
SAIN
STOP
OUTEN
P5jCR1
P5iCR1
Data input
Data input
B
D
Data output
Q
Y
P5i
S
Output latch
D
Data output
A
Q
P5j
Output latch
I
PIDS
(b) P56 to P54
(a) P57
STOP
OUTEN
Analog input
AINDS
SAIN
STOP
OUTEN
P5kCR1
P5lCR1
Data input
Control input
P5lCR2
Data input
Control input
D
Data output
Control output
D
Data output
Q
P5k
Output latch
Q
P5l
Output latch
Control output
(d) P52 to P51
(c) P53
STOP
OUTEN
P5mCR1
Data input
Control input
D
Data output
Q
P5m
Output latch
Control output
(d) P50
P5
(00005H)
7
P57
I
6
P56
AIN3
5
P55
AIN2
4
P54
AIN1
3
P53
INT2
TC1
2
P52
SO1
SDA1
SCK1
1
P51
0
P50
PWM9
PWM8
SL1
SLC1
INT0
TC2
(Initial value: 1111 1111)
AIN0
P5CR1
(00008H)
7
6
P5CR1
7
6
(00FFEH)
“0”
“0”
P5CR2
(00FBAH)
4
3
2
1
0
5
4
3
P35CR2 P34CR2
2
“0”
Write
only
1
0
P52CR2 P51CR2
(Initial value: 0*00 *00*)
0: Skin open drain
1: Tri-state
I/O Control for P5
7
6
5
4
3
2
P67S
P66S
P65S
P64S
PIDS
YBLCS
PIDS
(Initial value: 0000 0000)
0: Input mode
1: Output mode
I/O Control for P5
PSELCR
ORP6S
5
P57CR1 P56CR1 P55CR1 P54CR1 P53CR1 P52CR1 P51CR1 P50CR1
Selection of the output data
for port P57
Write
only
1
0
MPXS
(Initial value: 0000 0000)
0: The OSD output (I)
1: Port P57 output latch
Note 1:
*: Don’t care, i = 7, j = 6 to 4, k = 3, l = 2 to 1, m = 0.
Note 2:
P5CR1 cannot be used the read-modify-write instructions.
Write
only
(Bit manipulation instructions such as SET, CLR, etc. and logical operation such as ADN, OR, etc.)
Note 3:
Clear bit7, 6 and 3 to “0” in PSELCR.
Figure 2.2.5 Ports P5
88CS38B-50
2007-09-12
TMP88CS38B/CM38B/CP38B
2.2.5
Port P6 (P67 to P60)
Port P6 is an 8-bit input/output port which can be configured as an input or an output in
one-bit unit under software control. Input/output mode is selected by the corresponding bit
in the port P6 input/output control register (P6CR). Port P6 is configured as an input if its
corresponding P6CR bit is cleared to “0”, and as an output if its corresponding P6CR bit is
set to “1” and P6nS bit is set to “1”. P63 to P60 are sink open-drain ports. During reset,
P6CR is initialized to “0”, which configures port P6 as an input. The P6 output latches are
also initialized to “1”.
Data is written into the output latch regardless of the P6CR contents. Therefore initial
output data should be written into the output latch before setting P6CR.
Port P6 is used as an on screen display (OSD) output (R, G, B and Y/BL signal)/input
(RIN, GIN BIN, Y/BLIN signal), a test video signal output and AD converter analog input.
When used as a test video signal output pin, the output pins should be set to the output
mode and beforehand the signal control register (SGEN) should be set to “1”. When used as
a secondary function input, the input pins should be set to the input mode. When used as
an OSD output pin, the output pins should be set to the output mode and beforehand the
port P6 data selection register (P67S to P64S) should be clear to “0”. When used as port P6,
the signal control register (P67 to P64) should be set to “1”.
Note: Input mode port is read the state of input pin. When input/output mode is used mixed,
the contents of output latch setting input mode may be changed by executing bit
manipulation instructions.
Example: Sets the lower 4 bits (P63 to P60) in port P6 to the output mode, and the other bit to the input mode.
LD
(P6CR), 0FH
;
88CS38B-51
P6CR ← 00001111B
2007-09-12
TMP88CS38B/CM38B/CP38B
STOP
OUTEN
STOP
OUTEN
P6iCR
P63CR
Data input
Data input
RIN
D
Data output
A
Q
Y
P6i
Output latch
D
Data output
B S
R, G, B, Y/BL
Q
P63
Output latch
P6iS
(a) P67 to P64
(b) P63
STOP
OUTEN
Analog input
AINDS
SAIN
STOP
OUTEN
P6jCR
P62CR
Data input
GIN
Data input
BIN, Y/BLIN
D
Data output
A
Q
Y
P62
Output latch
D
Data output
B S
CSOUT
Q
SGEN
(c) P62
P6
(00006H)
P6CR
(0000DH)
7
P67
Y/BL
6
P66
B
(00FE6H)
(00FBAH)
5
P65
G
4
P64
R
3
P63
RIN
2
P62
GIN
CSOUT
1
P61
BIN
AIN5
0
P60
Y/BLIN
AIN4
7
6
5
4
3
2
1
0
P66CR
P65CR
P64CR
P63CR
P62CR
P61CR
P60CR
0: Input mode
1: Output mode
I/O Control for port P6
7
6
5
4
3
SGEN
SGVBLK
SGPAL
SGIV
SGCHS
SGEN
ORP6S
(b) P61 to P60
P67CR
P6CR
SGCR
P6j
Output latch
2
7
6
5
4
3
2
P66S
P65S
P64S
PIDS
YBLCS
P67S to P64S
Note 1:
Note 2:
1
0
SGPAT
P67S
Selection of the output data
for port P6i
(Initial value: 0000 0000)
Write
only
(Initial value: 0000 0000)
0: Disable
1: Enable
Function selection
(Initial value: 1111 1111)
Write
only
1
0
MPXS
0: The OSD output (R, G, B, Y/BL)
1: Port P6i output latch
(Initial value: 0000 0000)
Write
only
*: Don’t care, i = 7 to 4, j = 1 to 0.
P6CR and ORP6S cannot used with the read-modify-write instructions. (Bit manipulations such as SET,
CLR, etc. and logical operation such as AND, OR, etc.)
Note 3:
Clear bit2 and 0 to “0” in TVSCR
Figure 2.2.6 Ports P6, P6CR, and P67S to P64S
88CS38B-52
2007-09-12
TMP88CS38B/CM38B/CP38B
2.2.6
Port P7 (P71 to P70)
Port P7 is a 2bit input/output port, and is also used as a vertical synchronous signal ( VD )
input and a horizontal synchronous signal ( HD ) input for the on screen display (OSD)
circuitry.
The output latches, are initialized to “1” during reset. When used as an input port or a
secondary function pin, the output latch should be set to “1”.
When a read instruction for port P7 is executed, bits 7 to 2 in P7 are read in as undefined
data.
STOP
OUTEN
P7iCR
Data input
HD , VD
D
Data output
Q
P7i
Output latch
7
6
5
4
3
2
P7
(00007H)
P7CR
7
6
5
4
3
I/O Control for P7
0
P70
VD
HD
2
(00009H)
P7CR
1
P71
1
0
P71CR
P70CR
0: Input mode
1: Output mode
(Initial value: **** **11)
(Initial value: **** **00)
Write
only
Note: *: Don’t care, i = 1 to 0
Figure 2.2.7 Ports P7
88CS38B-53
2007-09-12
TMP88CS38B/CM38B/CP38B
2.3
Time Base Timer (TBT)
The time base timer generates time base for key scanning, dynamic displaying, etc. It also
provides a time base timer interrupt (INTTBT). The time base timer is controlled by a control
register (TBTCR) shown in Figure 2.3.1.
An INTTBT is generated on the first falling edge of source clock (the divider output of the
timing generator) after the time base timer has been enabled. The divider is not cleared by the
program; therefore, only the first interrupt may be generated ahead of the set interrupt period.
The interrupt frequency (TBTCK) must be selected with the time base timer disabled (When
the time base timer is changed from enabling to disabling, the interrupt frequency can’t be
changed.)
Both frequency selection and enabling can be performed simultaneously.
16
Example: Sets the time base timer frequency to fc/2 [Hz] and enables an INTTBT interrupt.
23
24
fc/2 , fc/2
21
22
fc/2 , fc/2
16
17
fc/2 , fc/2
14
15
fc/2 , fc/2
13
14
fc/2 , fc/2
12
13
fc/2 , fc/2
11
12
fc/2 , fc/2
9
10
fc/2 , fc/2
LD
(TBTCR), 00000010B
;
TBTCK = “010”
LD
(TBTCR), 00001010B
;
TBTEN = “1”
SET
(EIRL). 6
MPX
INTTBT
interrupt
A
request
B
C
Source clock
Source clock Rising
D Y
edge
E
detector
F
TBTEN
G
H S
INTTBT
3
TBTCK
TBTEN
Enable TBT
TBTCR
Interrupt
period
Time base timer control register
(a) Configuration
(b) Time base timer interrupt
Figure 2.3.1 Time Base Timer
88CS38B-54
2007-09-12
TMP88CS38B/CM38B/CP38B
TBTCR
(00036H)
7
6
5
4
3
“0”
−
−
“0”
TBTEN
TBTEN
2
1
0
TBTCK
(Initial value: 0**0 0***)
0: Disable
Time base timer
enable/disable
1: Enable
NORMAL, IDLE mode
DV1CK = 0
DV1CK = 1
23
fc/2 [Hz]
fc/2
21
fc/2
22
010
fc/2
16
fc/2
17
011
fc/2
14
fc/2
15
fc/2
13
fc/2
14
fc/2
12
fc/2
13
110
fc/2
11
fc/2
12
111
fc/2
9
fc/2
10
000
001
TBTCK
Time base timer interrupt
frequency select
100
101
fc/2 [Hz]
24
Write
only
Note 1:
fc: High-frequency clock [Hz], *: Don’t care
Note 2:
TBTCR is a write-only register and must not be used with any of read-modify-write
instruction.
Note 3:
Set bit7 and 4 in TBTCR to “0”.
Figure 2.3.2 Time Base Timer and Divider Output Control Register
Table 2.3.1 Time Base Timer Interrupt Frequency (Example: at fc = 16MHz)
Time Base Timer Interrupt Frequency [Hz]
TBTCK
NORMAL, IDLE Mode
DV1CK = 0
DV1CK = 1
000
1.90
001
7.62
3.81
010
244.14
122.07
011
976.56
488.28
100
1953.12
976.56
101
3906.25
1953.12
110
111
7812.50
31250
88CS38B-55
0.95
3906.25
15625
2007-09-12
TMP88CS38B/CM38B/CP38B
2.4
Watchdog Timer (WDT)
The watchdog timer is a fail-safe system to rapidly detect the CPU malfunctions such as
endless looping caused by noise or the like, or deadlock and resume the CPU to the normal
state.
The watchdog timer signal for detecting malfunction can be selected either a reset output or a
pseudo non-maskable interrupt request. However, selection is possible only once after reset. At
first the reset output is selected.
When the watchdog timer is not being used for malfunction detection, it can be used as a
timer to generate an interrupt at fixed intervals.
Note:
2.4.1
Care must be given in system design so as to protect the watchdog timer from disturbing
noise. Otherwise the watchdog timer may not fully exhibit its functionality.
Watchdog Timer Configuration
Reset release signal from T.G.
MPX
23
24
fc/2 , fc/2
21
22
fc/2 , fc/2
19
20
fc/2 , fc/2
17
18
fc/2 , fc/2
A
B
C
D
R
Binary counters
Y
Clock
Overflow
1
S
Reset output
WDT output
2
S
Q
Clear
Interrupt request
2
RESET
INTWDT
Internal reset
Q
S
WDTT
R
WDTEN
Writing
disable code
Writing
clear code
WDTOUT
Controller
00034H
WDTCR1
00035H
WDTCR2
Watchdog timer control registers
MPX: Multiplexer
T.G.: Timing generator
Figure 2.4.1 Watchdog Timer Configuration
88CS38B-56
2007-09-12
TMP88CS38B/CM38B/CP38B
2.4.2
Watchdog Timer Control
Figure 2.4.2 shows the watchdog timer control registers (WDTCR1, WDTCR2). The
watchdog timer is automatically enabled after reset.
(1) Malfunction detection methods using the watchdog timer
The CPU malfunction is detected at follows.
1.
Setting the detection time, selecting output, and clearing the binary counter.
2.
Repeatedly clearing the binary counter within the setting detection time.
Note:
The watchdog timer consists of an internal divider and two-stage binary counter.
Writing the clear code (4EH) clears the binary counter, but not the internal divider.
The minimum overflow time for the binary counter might be three quarters of the
WDTCR1 (WDTT) time setting depending on when the clear code (4EH) is written
into the WDTCR2 register. So, write the clear code on a cycle which is shorter than
that minimum overflow time.
If the CPU malfunctions such as endless looping or deadlock occur for any cause, the
watchdog timer output will become active at the rising of an overflow from the binary
counters unless the binary counters are cleared. At this time, when WDTOUT = 1 a
reset is generated, which drivers the RESET pin low to reset the internal hardware
and the external circuit. When WDTOUT = 0, a watchdog timer interrupt (INTWDT) is
generated.
The watchdog timer temporarily stops counting in STOP mode including warm-up or
IDLE mode, and automatically restarts (Continues counting) when the STOP/IDLE
mode is released.
88CS38B-57
2007-09-12
TMP88CS38B/CM38B/CP38B
21
Example: Sets the watchdog timer detection time to 2 /fc [s] and resets the CPU malfunction.
LD
(WDTCR2), 4EH
LD
(WDTCR1), 00001101B ; WDTT ← 10, WDTOUT ← 1
; Clears the binary counters
LD
(WDTCR2), 4EH
; Clears the binary counters
Within 3/4 of WDT
detection time
(always clear immediately before and after changing WDTT)
LD
(WDTCR2), 4EH
; Clears the binary counters
LD
(WDTCR2), 4EH
; Clears the binary counters
Within 3/4 of WDT
detection time
Watchdog Timer Register 1
WDTCR1
(00034H)
7
6
5
4
3
2
WDTEN
WDTEN
1
0
WDTOUT
WDTT
(Initial value: **** 1001)
0: Disable (It is necessary to write the disable code to
WDTCR2)
Watchdog timer
enable/disable
1: Enable
NORMAL mode
DV1CK = 0
WDTT
Note 1:
24
2 /fc
21
2 /fc
19
2 /fc
22
2 /fc
20
2 /fc
11
Write
only
26
2 /fc
23
2 /fc
01
10
WDTOUT
DV1CK = 1
25
2 /fc
00
Watchdog timer
detection time [s]
0: Interrupt request
Watchdog timer
output select
1: Reset output
WDTOUT cannot be set to “1” by program after clearing WDTOUT to “0”.
Note 2:
fc: High-frequency clock [Hz], *: Don’t care
Note 3:
WDTCR1 is a write-only register and must not be used with any of read-modify-write instructions.
Note 4:
The watchdog timer must be disabled or the counter must be cleared immediately before entering to the
STOP mode. When the counter is cleared, the counter must be cleared again immediately after releasing
the STOP mode.
Note 5:
Just right before disabling the watchdog timer, disable the acceptance of interrupts (DI) and clear the
watchdog timer.
If the watchdog timer is disabled under conditions other than the above, the proper operation cannot be
guaranteed.
Watchdog Timer Register 2
WDTCR2
7
6
5
4
3
2
1
0
(Initial value: **** ****)
(00035H)
WDTCR2
Watchdog timer control
code write register
4EH: Watchdog timer binary counter clear (Clear code)
B1H: Watchdog timer disable (Disable code)
Others: Invalid
Note 1:
The disable code is invalid unless written when WDTEN = 0.
Note 2:
*: Don’t care
Note 3:
The binary counter of the watchdog timer must not be cleared by the interrupt task.
Note 4:
Clears the binary counter does not clear the source clock.
Write
only
It is recommended that the time to clear is set to 3/4 of the detecting time.
Note 5:
The watchdog timer counter must be disabled by writing the disable code (B1H) to WDRCR2 after writing
WDTCR2 to. “4EH”.
Figure 2.4.2 Watchdog Timer Control Registers
88CS38B-58
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Watchdog timer enable
The watchdog timer is enabled by setting WDTEN (Bit3 in WDTCR1) to “1”.
WDTEN is initialized to “1” during reset, so the watchdog timer operates immediately
after reset is released.
Example: Disables watchdog timer
LDW
(WDTCR1), 00001000B
WDTEN ← 1
;
(3) Watchdog timer disable
To disable the watchdog timer, clear the interrupt mask enable flag (IMF) to “0” and
write the clear code (4EH) into WDTCR2. Then, clear WDTEN (Bit3 in WDTCR1) to “0”.
When WDTEN is “0”, the watchdog timer is disabled by writing the disable code (B1H)
into WDTCR2. If WDTEN is cleared to “0” after the disable code has been written into
WDTCR2, the watchdog timer is not disabled. While it is disabled, its binary counter is
cleared.
Example:
DI
;
Disables interrupt acceptance.
LD
(WDTCR2), 4EH
;
Clears the watchdog timer.
LDW
(WDTCR1), B101H
;
Disables the watchdog timer.
;
Enables interrupt acceptance.
EI
Table 2.4.1 Watchdog Timer Detection Time (Example: fc = 16 MHz)
Watchdog Timer Detection Time [s]
WDTT
NORMAL Mode
DV1CK = 0
2.4.3
DV1CK = 1
00
2.097
4.194
01
524.288 m
1.048
10
131.072 m
262.1
m
11
32.768 m
65.5
m
Watchdog Timer Interrupt (INTWDT)
This is a pseudo non-maskable interrupt which can be accepted regardless of the
contents of the EIR. If a watchdog timer interrupt or a software interrupt is already
accepted, however, the new watchdog timer interrupt waits until the previous interrupt
processing is completed (the end of the [RETN] instruction execution).
The stack pointer (SP) should be initialized before using the watchdog timer output as an
interrupt source with WDTOUT.
Example: Watchdog timer interrupt setting up
2.4.4
LD
SP, 023FH
;
Sets the stack pointer
LD
(WDTCR1), 00001000B
;
WDTOUT ← 0
Watchdog Timer Reset
If the watchdog timer output becomes active, a reset is generated, which drivers the
RESET pin (Sink open-drain input/output with pull-up) low to reset the internal hardware.
The reset output time is about 8/fc to 24/fc [s] (0.5 to 1.5 μs at fc = 16.0 MHz).
Note: If there is any fluctuation in the oscillation frequency at the start of clock oscillation, the
reset time includes error. Thus, regard the reset time as an approximate value.
88CS38B-59
2007-09-12
TMP88CS38B/CM38B/CP38B
19
2 /fc [s]
17
2 /fc
(WDTT = 11B)
Clock
Binary counter
1
2
3
0
1
2
3
0
Overflow
INTWDT interrupt
WDT reset output
(High-Z)
(“L” output)
Writes 4EH to WDTCR2
Figure 2.4.3 Watchdog Timer Interrupt/Reset
88CS38B-60
2007-09-12
12
88CS38B-61
Note:
2
Clock
SCAP1
Capture
Window mode
S
AY
B
MPX
TC1DRA
CMP
16-bit timer registers 1A, 1B
TC1DRB
16-bit up counter
Clear
INTTC1 interrupt
Match
Be sure to set the function of input/output pins correctly. For details, see the section on I/O port control registers.
Timer/counter 1 control register
TC1CR
A
B Y
C
S
D
Clear
Set Q
Command start
METT1
External
trigger start
MPX
TC1CK
S A Y B
2
TC1S
Decoder
MPX
Falling
External
trigger
Edge detector
Rising
fc/2 , fc/2
7
8
fc/2 or fc/2
3
4
fc/2 or fc/2
11
TC1 pin
INT2ES
Pulse width
measurement
mode
MPX
B
A
CMP: Comparator
MPX: Multiplexer
Pulse width
measurement
mode
2.5.1
Y
2.5
S
MCAP1
TMP88CS38B/CM38B/CP38B
16-Bit Timer/Counter 1 (TC1A)
Configuration
Figure 2.5.1 Timer/Counter 1
2007-09-12
TMP88CS38B/CM38B/CP38B
2.5.2
Control
The timer/counter 1 is controlled by a timer/counter 1 control register (TC1CR) and two
16-bit timer registers (TC1DRA and TC1DRB).
TC1DRA
(00010, 00011H)
15
14
13
12
11
10
9
8
7
6
5
TC1DRAH (00011H)
4
3
2
1
0
TC1DRAL (00010H)
Read/Write
TC1DRB
(00012, 00013H)
TC1DRBH (00013H)
TC1DRBL (00012H)
Read only
TC1CR
(00014H)
TC1M
7
6
5
“0”
ACPAP1
MCAP1
METT1
MPPG1
4
3
TC1S
TC1 operating mode select
2
TC1CK
00:
01:
10:
11:
1
0
Read/Write
TC1M
(Initial value: 0000 0000)
Timer/external trigger timer/event counter mode
Window mode
Pulse width measurement mode
Reserved
NORMAL, IDLE mode
DV7CK = 0, DVCK = 00
DV1CK = 0
TC1CK
TC1 source clock select [Hz]
fs/2
fc/2
7
fc/2
8
fc/2
3
fc/2
4
fc/2
01
10
11
TC1S
00:
01:
10:
11:
TC1 start control
DV1CK = 1
11
00
12
R/W
External clock (TC1 pin input)
Stop and counter clear
Command start
External trigger start at the rising edge
External trigger start at the falling edge
Timer Extend Event Window Pulse
○
○
○
○
○
○
×
×
×
×
ACAP1
Auto-capture control
0: Auto-capture disable
×
○
○
×
1: Auto-capture enable
MCAP1
Pulse width measurement
mode control
0: Double edge capture
1: Single edge capture
METT1
External trigger timer
mode control
0: Trigger start
1: Trigger start and stop
○
○
○
○
○
○
PPG
○
×
○
○
Note 1:
fc: High-frequency clock [Hz]
Note 2:
The timer register consists of two shift registers. A value set in the timer register is put in effect at the rising
edge of the first source clock pulse that occurs after the upper data (TC1DRAH) are written. Therefore, the
lower byte must be written before the upper byte (It is recommended that a 16-bit access instruction be
used in writing). Writing only the lower data (TC1DRAL) does not put the setting of the timer register in
effect.
Note 3:
Set the mode, source clock PPG control and timer F/F control when TC1 stops (TC1S = 00).
Note 4:
Auto capture can be used in only timer, event counter, and window modes.
Note 5:
Values to be loaded to timer registers must satisfy the following condition.
TC1DRA > TC1DRB, TC1DRA > 1
Note 6:
Always write “0” to TFF1 except PPG output mode.
Note 7:
On entering STOP mode, the TC1 start control (TC1S) is cleared to “00” automatically. So, the timer stops.
Once the STOP mode has been released, to start using the timer counter, set TC1S again.
Note 8:
In the Auto-capture function, when the capture value is read after stop and clear counter or Auto-capture
disable is executed by the TC1 start control (TC1S), the correct capture value might not be able to be
read.When using Auto-capture function, set capture to enable.
Note 9: Since the up-counter value is captured into TC1DRB by the source clock of up-counter after setting
TC1CR<ACAP1> to “1”. Therefore, to read the captured value, wait at least one cycle of the internal source
clock before reading TC1DRB for the first time.
Figure 2.5.2 Timer registers and TC1 control register
88CS38B-62
2007-09-12
TMP88CS38B/CM38B/CP38B
2.5.3
Function
Timer/counter 1 has five operating modes: Timer, external trigger timer, event counter,
window, pulse width measurement.
(1) Timer mode
In this mode, counting up is performed using the internal clock. The contents of
TC1DRA are compared with the contents of up counter. If a match is found, an INTTC1
interrupt is generated, and the counter is cleared to “0”. Counting up resumes after the
counter is cleared. The current contents of up counter can be transferred to TC1DRB
by setting ACAP1 (Bit6 in TC1CR) to “1” (Software capture function). (Auto-capture
function)
Table 2.5.1 Source Clock (Internal clock) for Timer/Counter 1 (Example: at fc = 16.0 MHz)
NORMAL, IDLE Mode
DV1CK = 0
TC1CK
Resolution [μs]
DV1CK = 1
Maximum Time
Setting [s]
Resolution [μs]
Maximum Time
Setting [s]
16.78
00
128.0
8.39
256.0
01
8.0
0.524
16.0
1.049
10
0.5
32.77 m
1.0
65.54 m
Example 1: Sets the timer mode with source clock fc/2 [Hz] and generates an interrupt 1 later (at fc = 16 MHz)
11
LDW
(TC1DRA), 1E84H
;
Sets the timer register (1 s ÷ 2 /fc = 1E84H)
(EIRL). 4
;
Enable INTTC1
11
DI
SET
EI
LD
(TC1CR), 00000000B
;
Selects the source clock and mode
LD
(TC1CR), 00010000B
;
Starts TC1
Example 2: Auto capture
LD
(TC1CR), 01010000B
;
ACAP1 ← 1 (Capture)
:
:
;
Wait at least one cycle of the internal source clock
LD
WA, (TC1DRB)
;
Reads the capture value
88CS38B-63
2007-09-12
TMP88CS38B/CM38B/CP38B
Count start
Source clock
Up counter
0
TC1DRA
?
1
2
3
n−1 n 0
4
1
2
3
5
4
6
7
n
Match detect
Counter clear
INTTC1 interrupt
(a) Timer mode
Source clock
m−2
Up counter
TC1DRB
m−1
m−1
?
m+1
m
Capture
m
m+2
m+1
n−1
m+2
n+1
n
n−1
Capture
n+1
n
ACAP1
(b) Auto capture
Figure 2.5.3 Timer Mode Timing Chart
(2) External trigger timer mode
In this mode, counting up is started by an external trigger. This trigger is the edge of
the TC1 pin input. Either the rising or falling edge can be selected with TC1S. Source
clock is an internal clock. The contents of TC1DRA is compared with the contents of up
counter. If a match is found, an INTTC1 interrupt is generated, and the counter is
cleared to “0” and halted. The counter is restarted by the selected edge of the TC1 pin
input.
When METT1 (Bit6 in TC1CR) is “1”, inputting the edge to the reverse direction of
the trigger edge to start counting clears the counter, and the counter is stopped.
Inputting a constant pulse width can generate interrupts. When METT1 is “0”, the
reverse directive edge input is ignored. The TC1 pin input edge before a match
detection is also ignored.
The TC1 pin input has the noise rejection; therefore, pulses of 7/fc [s] or less are
rejected as noise. A pulse width of 13/fc [s] or more is required for edge detection in
NORMAL or IDLE mode.
Example 1:
Detects rising edge in TC1 pin input and generates an interrupt 100 μs later. (at fc = 16.0 MHz,
DV1CK = 1)
LDW
(TC1DRA), 0064H
;
100 μs ÷ 2 /fc = 64H
(EIRL). 4
;
INTTC1 interrupt enable
4
DI
SET
EI
Example 2:
LD
(TC1CR), 00001000B
;
Selects the source clock and mode
LD
(TC1CR), 00101000B
;
TC1 external trigger start, METT1 = 0
Generates an interrupt, inputting “L” level pulse (Pulse width: 4 ms or more) to the TC1 pin. (at fc =
16.0 MHz, DV1CK = 1)
LDW
(TC1DRA), 00FAH
;
4 ms ÷ 2 /fc = FAH
(EIRL). 4
;
INTTC1 interrupt enable
8
DI
SET
EI
LD
(TC1CR), 00000100B
;
Selects the source clock and mode
LD
(TC1CR), 01110100B
;
TC1 external trigger start, METT1 = 1
88CS38B-64
2007-09-12
TMP88CS38B/CM38B/CP38B
Count start
Count start
TC1S = 10 at the
rising edge
TC1 pin input
Internal clock
0
Up counter
1
2
TC1DRA
3
n−1 n
4
n
Match detect
INTTC1
interrupt
1
0
2
3
Counter clear
(a) Trigger start (METT1 = 0)
Counter clear
Count start
TC1S = 10
at the rising
edge
Count start
TC1 pin input
Internal clock
Up counter
0
1
2
m−1 m
3
TC1DRA
1
0
2
n−1 n
3
n
Match detect
INTTC1
interrupt
0
Counter clear
m<n
(b) Trigger start and stop (METT1 = 1)
Figure 2.5.4 External Trigger Timer Mode Timing Chart
(3) Event counter mode
In this mode, events are counted at the edge of the TC1 pin input (Either the rising
or falling edge can be selected with the external trigger TC1CR<TC1S>). The contents
of TC1DRA are compared with the contents of up counter. If a match is found, an
INTTC1 interrupt is generated, and the counter is cleared.
Match detect is executed on other edge of count-up. A match can not be detected and
INTTC1 is not generated when the pulse is still in same state.
Setting ACAP1 to “1” transfers the current contents of up counter to TC1DRB
(Auto-capture function).
Count start
TC1S = 10
at the falling
edge
TC1 pin input
0
Up counter
TC1DRA
?
1
2
n−1
n
0
1
2
n
Match detect
Counter clear
INTTC1 interrupt
Figure 2.5.5 Event Counter Mode Timing Chart
Table 2.5.2 Input Pulse Width for Timer/Counter 1
Minimum Pulse Width [s]
NORMAL/IDLE
3
“H” Width
2 /fc
“L” Width
2 /fc
3
88CS38B-65
2007-09-12
TMP88CS38B/CM38B/CP38B
(4) Window mode
Counting up is performed on the rising edge of the pulse that is the logical AND-ed
product of the TC1 pin input (Window pulse) and an internal clock. The contents of
TC1DRA are compared with the contents of up counter. If a match is found, an INTTC1
interrupt is generated, and the counter is cleared. Positive or negative logic for the TC1
pin input can be selected with bit4 or 5 in TC1CR.
It is necessary that the maximum applied frequency be such that the counter value
can be analyzed by the program. That is; the frequency must be considerably slower
than the selected internal clock.
Count start
Count stop
Count start
Command start
TC1 pin input
Internal clock
Up counter
0
TC1DRA
?
1
2
3
4
5
6
7 0
1
2
3
n
Match detect
Counter clear
INTTC1 interrupt
(a) Positive logic (at TC1S = 10)
Command start
Count start
Count stop
Count start
TC1 pin input
Internal clock
Up counter
TC1DRA
0
?
1
2
3
4
5
6
7
8
9 0
1
9
Match detect
INTTC1 interrupt
Counter clear
(a) Negative logic (at TC1S = 11)
Figure 2.5.6 Window Mode Timing Chart
(5) Pulse width measurement mode
In this mode, counting is started by the external trigger (Set to external trigger start
by TC1CR). The trigger can be selected either the rising or falling edge of the TC1 pin
input. The source clock is used an internal clock. On the next falling (rising) edge, the
counter contents are transferred to TC1DRB and an INTTC1 interrupt is generated.
The counter is cleared when the single edge capture mode is set. When double edge
capture is set, the counter continues and, at the next rising (falling) edge, the counter
contents are again transferred to TC1DRB. If a falling (rising) edge capture value is
required, it is necessary to read out TC1DRB contents until a rising (falling) edge is
detected. Falling or rising edge is selected with the external trigger TC1S (Bit4 or 5 in
TC1CR), and single edge or double edge is selected with MCAP1 (Bit6 in TC1CR).
Note 1: Be sure to read the captured value from TC1DRB before the next trigger edge is
detected. If fail to read it, it becomes undefined. It is recommended that a 16-bit access
instruction be used to read from TC1DRB.
Note 2: If either the falling or rising edge is used in capturing values, the counter stops at “1”
after a value has been captured until the next edge is detected. So, the value captured
next will become “1” larger than the value captured right after capturing starts.
88CS38B-66
2007-09-12
TMP88CS38B/CM38B/CP38B
Note 3: In the Pulse width measurement mode, the capture value of the first time after the timer
starts might not be a correct value. Thus, execute the dummy read once.
Example: Duty measurement (Resolution fc/2 [Hz] DV1CK = 0)
7
CLR
(INTTC1SW). 0
;
INTTC1 service switch initial setting:
Clears bit0 of INTTC1SW. This bit is inverted by
CPL instruction before INTTC1 is generated.
LD
(TC1CR), 00000110B
;
Sets the TC1 mode and source clock
(EIRL). 4
;
Enables INTTC1
LD
.
.
.
CPL
(TC1CR), 00100110B
;
Starts TC1 with an external trigger at MCAP1 = 0
(INTTC1SW). 0
;
Complements INTTC1 service switch
JRS
F, SINTTC1
LD
WA, (TC1DRBL)
DI
SET
EI
PINTTC1:
;
Reads TC1DRB (“H” level pulse width)
Lower address in TC1DRBL: TC1DRB
LD
(HPULSE), WA
RETI
SINTTC1:
LD
WA, (TC1DRBL)
(WIDTH), WA
VINTTC1:
LD
.
.
.
RETI
.
.
.
DW
PINTTC1
;
Reads TC1DRB (Period)
;
Duty calculation
;
Sets INTTC1
WIDTH
HPULSE
TC1 pin
INTTC1
INTTC1SW
88CS38B-67
2007-09-12
88CS38B-68
INTTC1 interrupt
TC1DRB
Up counter
Internal clock
TC1 pin input
INTTC1 interrupt
TC1DRB
Up counter
Internal clock
TC1 pin input
0
Count start
0
Count start
1
1
2
2
3
3
4
4
n
Capture
n 0
1
n
n+1
n
Capture
n+2
(b) Double edge capture (MCAP1 = 0)
n−1
(a) Single edge capture (MCAP1 = 1)
n−1
1
2
m
Capture
m−1 m 0
Count start
Count start
4
1
m
Capture
m−1 m 0
3
[Application]
2
n’
n’ + 1 n’ + 2
n’
Capture
(1) Period/frequency measurement
(2) Duty measurement
n’ − 1
[Application] High or low pulse width measurement
3
Trigger
TMP88CS38B/CM38B/CP38B
Figure 2.5.7 Pulse Width Measurement Mode Timing Chart
2007-09-12
TMP88CS38B/CM38B/CP38B
2.6
16-Bit Timer/Counter 2 (TC2A)
2.6.1
Configuration
MPX
Port
(Note)
TC2 pin
TC2S
H
Window
23
24
fc/2 or fc/2
13
14
fc/2 or fc/2
8
9
fc/2 or fc/2
3
4
fc/2 or fc/2
A
B
CY
D
Clear
B
Timer/
event counter
Y
Source
A clock
S
16-bit up counter
TC2M
CMP
S
3
TC2CK
INTTC2
interrupt
TC2S
TC2DR
TC2CR
16-bit timer register 2
MPX: Multiplexer
CMP: Comparator
TC2 control register
Note:
Propagation of control input/output requires the correct I/O port setting. For details, see the section on I/O
ports.
Figure 2.6.1 Timer/Counter 2 (TC2)
88CS38B-69
2007-09-12
TMP88CS38B/CM38B/CP38B
2.6.2
Control
The timer/counter 2 is controlled by a timer/counter 2 control register (TC2CR) and a
16-bit timer register 2 (TC2DR). Reset does not affect TC2DR.
TC2DR
(00016H, 00017H)
15
14
13
12
11
10
9
8
7
6
TC2DRH (00017H)
5
4
3
2
1
0
TC2DRL (00016H)
Read/Write
7
TC2CR
(00015H)
TC2M
6
5
TC2S
TC2
operating mode select
4
3
2
1
0
TC2CK
TC2M
(Initial value: **00 00*0)
0: Timer/event counter mode
1: Window mode
NORMAL1/2, IDLE1/2 mode
DV1CK = 0
fc/2
fc/2
24
fc/2
13
fc/2
14
fc/2
8
fc/2
9
011
fc/2
3
fc/2
4
100
Reserved
101
Reserved
000
001
TC2CK
TC2S
TC2
source clock select [Hz]
TC2
start control
DV1CK = 1
23
010
Write
only
Reserved
Reserved
110
Reserved
111
External clock (TC2 pin input)
0: Stop and counter clear
1: Start
Note 1:
fc: High-frequency clock [Hz], *: Don’t care.
Note 2:
Writing to the lower byte of timer register 2 (TC2DRL), the comparison is inhibited until the upper byte
(TC2DRH) is written. After writing to the upper byte, any match during 1 machine cycle (Instruction
execution cycle) is ignored.
Note 3:
Set the mode and source clock when the TC2 stops (TC2S = 0).
Note 4:
Values to be loaded to timer registers must satisfy the following condition.
Note 5:
TC2CR are write-only registers and must not be used with any of the read-modify-write instructions.
TC2DR > 1
Note 6:
When STOP mode is started, timer counter is stopped and cleared. Set TC2S to “1” after STOP mode is
released for restarting timer counter.
Figure 2.6.2 Timer Registers 2 and TC2 Control Register
88CS38B-70
2007-09-12
TMP88CS38B/CM38B/CP38B
2.6.3
Function
The timer/counter 2 has three operating modes: Timer, event counter and window modes.
(1) Timer mode
In this mode, the internal clock is used for counting up. The contents of TC2DR are
compared with the contents of up counter. If a match is found, a timer/counter 2
interrupt (INTTC2) is generated, and the counter is cleared. Counting up is resumed
after the counter is cleared.
Table 2.6.1 Source Clock (Internal clock) for Timer/Counter 2 (at fc = 16.0 MHz)
NORMAL, IDLE mode
DV1CK = 0
TC2CK
DV1CK = 1
Maximum
Time Setting
Resolution
Maximum
Time Setting
Resolution
000
524.3 [ms]
9.54 [h]
001
512.0 [μs]
33.6 [s]
1.02 [ms]
1.05 [s]
19.1
[h]
010
16.0 [μs]
1.05 [s]
32.0 [μs]
011
0.5 [μs]
32.8 [ms]
1.0 [μs]
100
Reserved
Reserved
Reserved
Reserved
101
Reserved
Reserved
Reserved
Reserved
1.12 [min]
2.09 [s]
65.5
[ms]
Example: Sets the source clock fc/2 [Hz] and generates an interrupt event 25 ms (at fc = 16 MHz, DV1CK = 1)
4
LDW
(TC2DR), 61A8H
;
Sets TC2DR (25 ms ÷ 2 /fc = 61A8H)
(EIRH).6
;
Enable INTTC2 interrupt
4
DI
SET
EI
LD
(TC2CR), 00001100B
;
Selects TC2 source clock
LD
(TC2CR), 00101100B
;
Starts TC2
Count start
Source clock
Up counter
0
1
2
3
n−1 n 0
4
Match detect
Timer trigger
1
2
3
Counter clear
n
INTTC2 interrupt
Figure 2.6.3 Timer Mode Timing Chart
88CS38B-71
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Event counter mode
In this mode, events are counted on the rising edge of the TC2 pin input. The
contents of TC2DR are compared with the contents of the up counter. If a match is
found, an INTTC2 interrupt is generated, and the counter is cleared. The minimum
pulse width to the TC2 pin is shown in Table 2.6.2. Two or more machine cycles are
required for both the “H” and “L” levels of the pulse width. Match detect is executed on
the falling edge of the TC2 pin. A match can not be detected and INTTC2 is not
generated when the pulse is still in a falling state.
Example: Sets the event counter mode and generates an INTTC2 interrupt 640 counts later.
LDW
(TC2DR), 640
;
Sets TC2DR
(EIRH). 6
;
Enables INTTC2 interrupt
DI
SET
EI
LD
(TC2CR), 00011100B
;
Selects TC2 source clock
LD
(TC2CR), 00111100B
;
Starts TC2
Table 2.6.2 Timer/Counter 2 External Clock Source
Minimum Pulse Width [S]
NORMAL, IDLE Mode
3
“H” Width
2 /fc
“L” Width
2 /fc
3
Count start
TC2 pin input
Up counter
0
1
2
n−1
3
Match detect
Timer register
n
0
1
2
3
Counter clear
n
INTTC2 interrupt
Figure 2.6.4 Event Counter Mode Timing Chart
88CS38B-72
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) Window mode
In this mode, counting up performed on the rising edge of an internal clock during
TC2 external pin input (window pulse) is “H” level. The contents of TC2DR are
compared with the contents of up counter. If a match found, an INTTC2 interrupt is
generated, and the up counter is cleared.
The maximum applied frequency (TC2 input) must be considerably slower than the
selected internal clock.
Example:
Generates an interrupt, inputting “H” level pulse width of 120 ms or more. (at fc = 16.0 MHz, DV1CK
= 1)
LDW
(TC2DR), 0075H
;
Sets TC2DR (120 ms ÷ 2 /fc = 0075H)
(EIRH). 6
;
Enables INTTC2 interrupt
14
DI
SET
EI
LD
(TC2CR), 00000101B
;
Selects TC2 source clock
LD
(TC2CR), 00100101B
;
Starts TC2
TC2 pin input
Internal clock
Up counter
TC2DR
0
1
2
n−3
n−2
n−1 n 0
1
2
3
n
Match detect
Counter clear
INTTC2 interrupt
Figure 2.6.5 Window Mode Timing Chart
88CS38B-73
2007-09-12
TMP88CS38B/CM38B/CP38B
2.7
8-Bit Timer/Counter 3 (TC3B)
2.7.1
Configuration
Rising
Edge
detector
TC3S
INTTC3
interrupt
Falling
TC3ES
Clear
TC3 pin
A
Y
B
H
A
B
C
D Y
E
F
G
S
fc/213 or fc/214
fc/212 or fc/213
fc/211 or fc/212
fc/210 or fc/211
fc/29 or fc/210
fc/28 or fc/29
fc/27 or fc/28
Source clock
8-bit up counter
Overfolw
TC3S
Comparator
Match detect
A
Y
B
3
Capture
Capture
TC3DRB
S
TC3DRA
TC3CK
ACAP
8-bit timer register
TC3S
TC3M
TC3CR
TC3 control register
Note: Propagation of control input/output requires the correct I/O port setting. For details, see the section on I/O ports.
Figure 2.7.1 Timer/Counter 3 (TC3)
88CS38B-74
2007-09-12
TMP88CS38B/CM38B/CP38B
2.7.2
Control
The timer/counter 3 is controlled by a timer/counter 3 control register (TC3CR) and two
8-bit timer registers (TC3DRA and TC3DRB) and port multiplex control register
(PMPXCR).
TC3DRA
(0018H)
TC3DRB
(0019H)
7
TC3CR
(001AH)
7
6
5
4
3
2
1
0
Read/Write (Initial value: 1111 1111)
Read only (Initial value: 1111 1111)
6
5
ACAP
4
3
TC3S
2
1
0
TC3K
TC3M
TC3
operating mode select
TC3M
(Initial value: *0*0 0000)
0: Timer/event counter
1: Capture
NORMAL, IDLE mode
DV1CK = 0
000
001
TC3CK
010
TC3
source clock select [Hz]
011
ACAP
Auto-capture control
fc/2
14
fc/2
12
fc/2
13
fc/2
11
fc/2
12
fc/2
10
fc/2
11
fc/2
10
100
fc/2
101
fc/2
8
fc/2
9
fc/2
7
fc/2
8
111
TC3S
13
9
110
TC3
start control
DV1CK = 1
fc/2
Write
only
External clock (TC3 pin input)
0: Stop and clear
1: Start
0:
−
1: Auto-capture enable
Note 1:
fc: High-frequency clock [Hz], *: Don’t care.
Note 2:
Set the mode and source clock when the TC3 stops (TC3S = 0).
Note 3:
Values to be loaded to timer register 3A must satisfy the following condition
TC3DRA > 0 (in the timer and event counter mode).
Note 4:
Auto-capture can be used only int the timer and event counter mode.
Note 5:
Before setting TC3DRA or switching the operation mode, stop the TC3 (TC3S = 0).
Note 6:
When STOP mode is started, timer counter is stopped and TC3 start control (TC3S) is cleared to “0”
automatically. Set TC3S to “1” after STOP mode is released for restarting timer counter.
Note 7:
TC3CR, TCESCR is a write-only register and must not be used with any of the read-modify-write
instructions.
PMPXCR
(0027H)
7
6
“0”
CHS
TC3ES
Note 8
5
4
3
2
1
0
TC4ES
TC3ES
(Initial value: 00** **00)
0: Normal
1: Invert
TC3 input control
Write
only
Always write “0” to bit7 in PMPXCR.
Figure 2.7.2 Timer Registers 3 and TC3 Control Register
88CS38B-75
2007-09-12
TMP88CS38B/CM38B/CP38B
2.7.3
Function
The timer/counter 3 has three operating modes: timer, event counter, and capture mode.
When it is used in the capture mode, the noise rejection time of TC3 pin input can be set
by remote control receive control register.
(1) Timer mode
In this mode, the internal clock is used for counting up. The contents of TC3DRA are
compared with the contents of up counter. If a match is found, a timer/counter 3
interrupt (INTTC3) is generated, and the up counter is cleared. The current contents of
up counter are loaded into TC3DRB by setting ACAP (Bit6 in TC3CR) to “1”
(Auto-capture function).
The contents of up counter can be easily confirmed by executing the read instruction
(RD instruction) of TC3DRB. Loading the contents of up counter is not synchronized
with counting up. The contents of over flow (FFH) and 00H can not be loaded correctly.
It is necessary to consider the count cycle.
Clock
Counter
FE
FF
FE
TC3DRB
00
01
FF/00
01
Table 2.7.1 Source Clock (Internal clock) for Timer/Counter 3 (Example: at fc = 16.0 MHz)
NORMAL, IDLE Mode
DV1CK = 0
TC3CK
Resolution [μs]
DV1CK = 1
Maximum Setting
Time [ms]
Resolution [μs]
Maximum Setting
Time [ms]
000
512
130.6
1024
261.1
001
256
65.3
512
130.6
010
128
32.6
256
65.3
011
64
16.3
128
32.6
100
32
8.2
64
16.3
101
16
4.1
32
8.2
110
8
2.0
16
4.1
88CS38B-76
2007-09-12
TMP88CS38B/CM38B/CP38B
Count start
Source clock
Up counter
0
Timer register B
?
1
2
3
n−1 n 0
4
1
2
3
4
5
6
7
n
Match detect
Counter clear
INTTC3 interrupt
(a) Timer mode
Source clock
m−2
Up counter
Timer register B
m−1
m−1
?
m
m+1
Capture
m
n−1
m+2
m+1
m+2
n
n−1
n+1
Capture
n
n+1
ACAP1
(b) Auto capture
Figure 2.7.3 Timer Mode Timing Chart
(2) Event counter mode
In this mode, the TC3 pin input pulses are used for counting up Either the rising on
falling edge can be selected with TC3ES (Bit0 in PMPXCR). The contents of TC3DRA
are compared with the contents of the up counter. If a match is found, an INTTC3
interrupt is generated and the counter is cleared. Match detect is executed on the
falling edge of the TC3 pin. A match can not be detected, and INTTC3 is not generated
when the pulse is still in a falling state.
The maximum applied frequency is shown in Table 2.7.2. Two or more machine
cycles are required for both the high and low levels of the pulse width.
The current contents of up counter are loaded into TC3DRB by setting ACAP (Bit6 in
TC3CR) to “1” (Auto-capture function).
The contents of up counter can be easily confirmed by executing the read instruction
(RD instruction) of TC3DRB. Loading the contents of up counter is not synchronized
with counting up. The contents of over flow (FFH) and 00H can not be loaded correctly.
It is necessary to consider the count cycle.
Example: Generates an interrupt every 0.5 s, inputting 50 Hz pulses to the TC3 pin.
LD
(TC3CR), 00001110B
;
LD
(TC3DRA), 19H
;
Sets TC3 mode and source clock
0.5 s ÷ 1/50 = 25 = 19H
LD
(TC3CR), 00011100B
;
Starts TC3
Table 2.7.2 Source Clock (External clock) for Timer/Counter
Minimum Applied Frequency [Hz]
NORMAL, IDLE Mode
2
“H” Width
2 /fc
“L” Width
2 /fc
2
88CS38B-77
2007-09-12
TMP88CS38B/CM38B/CP38B
Count start
TC3 pin input
Up counter
0
1
2
n−1
3
n
Match detect
Timer register
0
1
2
3
Counter clear
n
INTTC3 interrupt
Figure 2.7.4 Event Counter Mode Timing Chart
(3) Capture mode
In this mode, the pulse width, period and duty of the TC3 pin input are measured in
this mode, which can be used in decoding the remote control signals or distinguishing
AC 50/60 Hz, etc. The TC3 pin input can have its polarity changed between normal and
inverse by using the TC3ES Register.
a.
If TC3ES = “0” (Non-inverting input)
Once command operation has started, the counter free-runs on an internal
source clock.
When the falling edge of the TC3 pin input is detected, the counter value is
loaded into TC3DRB. When the rising edge is detected, the counter value is loaded
into TC3DRA, and the counter is cleared, generating an INTTC3 interrupt.
If the rising edge is detected right after command operation has started, no
capture to TC3DRB and an INTTC3 interrupt occurs only on capture to TC3DRA.
If a read instruction is executed for TC3DRB, the value that exists at the end of
the previous capture (immediately after a reset, “FF”) is read.
b.
If TC3ES = “1” (Inverse input)
Once command operation has started, the counter free-runs on an internal
clock.
When the rising edge of the TC3 pin input is detected, the counter value is
loaded into TC3DRB. When the falling edge is detected, the counter value is
loaded into TC3DRA, and the counter is cleared, generating an INTTC3 interrupt.
If the falling edge is detected right after command operation has started, the
counter value is not captured into TC3DRB and an INTTC3 interrupt occurs only
on capture to TC3DRA. If a read instruction is executed for TC3DRB, the value
that exists at end of the previous capture (immediately after a reset, “FF”) is read.
The minimum acceptable input pulse width is equal to the length of one source
clock period selected by TC3CR <TC3CK>.
Table 2.7.3 TC3INV-based Capture Input Edges
TC3ES
Capture into TC3DRB
“0”
(Non-inverting input)
Falling edge
Rising edge
“1”
(Inverting input)
Rising edge
Falling edge
Note:
Capture into TC3DRA
INTTC3 Interrupt
Capture of the TC3 pin input requires at least 1 cycle of the selected source clock.
88CS38B-78
2007-09-12
88CS38B-79
Reading TC3DRA
INTTC3 interrupt
TC3DRB
TC3DRA
Internal waveform
(Invert)
TC3 pin input
Up counter
Source clock
TC3S
Reading TC3DRA
INTTC3 interrupt
TC3DRB
TC3DRA
Internal waveform
(Normal)
TC3 pin input
Up counter
Source clock
TC3S
1
0
1
Command start
0
Command start
i−1
i−1
i
i
0
1
Capture
i
i
i+1
k−1
k
k−1 k 0
m−1
m
m
m+1
n−1 n 0
m−1 m 0
Capture
m
1
Capture
n
1
2
Capture
n−2
n−3 n−2 n−1 n 0
b) In case of TC3ES = “1” (Invert)
k
k+1
a) In case of TC3ES = “0” (Normal)
Capture
k
1
n
1
3
1
3
2
3
2
FF (Overflow)
2
Overflow
1
When TC3DRA is not read, capture
and overflow detection are stopped.
FE FF
FF
FE FF
TMP88CS38B/CM38B/CP38B
Figure 2.7.5 Capture Mode Timing Chart
2007-09-12
TMP88CS38B/CM38B/CP38B
The edge of TC3 pin input is detected in the remote control receive circuit with noise
rejection. The remote control receive circuit is controlled by the remote control receive
control register (RCCR). The remote control receive status register (RCSR) can monitor
the polarity selection and noise rejection circuit.
Rising
Polarity
select
TC3IN
8
Noise reject circuit
(5-bit up-down counter)
MPX
A
9
fc/2 or fc/2
Capture
control
Edge detector
Falling
B Y
S
TC3
Source clock
RCSCK
RPOLS
5
RCNC
RCNF
RCOVF
RNCM
RCCR/RCSR
MPX: Multiplexer
Remote control receive control/status register
Figure 2.7.6 Remote Control Receiving Circuit
88CS38B-80
2007-09-12
TMP88CS38B/CM38B/CP38B
RCCR
(00026H)
RCEN
RPOLS RCSCK
RCNC
Noise reject time select
RCNC
(Initial value: 0001 1111)
Write
only
(Source clock) × (RCNC − 1) [s]
02H ≤ RCNC ≤ 1FH
NORMAL, IDLE mode
DV1CK = 0
Noise reject cricuit
RCSCK
Source clock select
0
RPOLS
RCEN
RCSR
(00026H)
0: Positive
select
1: Negative
Remote control receive circuit
0: Disable
operation control
1: Enable
R/W
9
2 /fc
2 /fc
1
Remote control signal polarity
DV1CK = 1
8
TC3CK
(Note 2)
Write
only
Note 1:
Set RPOLS and RCSCK when the timer/counter stops (TC3S = 0).
Note 2:
Source clock of timer/counter 3.
Note 3:
fc: High-frequency clock [Hz], *: Don’t care
Note 4:
RCCR includes a write-only register and must not be used with any of read-modify-write instructions.
Note5:
Values to be loaded to RCNC must satisfy the following condition (02 ≤ RCNC ≤ 1F).
RCNF
RPOLS RCSCK RCOVF
RNCM
RCOVF
RNCM
(Initial value: 0000 0***)
Remote control signal monitor
0: Low level
after noise rejector
1: High level
Noise reject circuit overflow
0: Signal and definition by overwriting the noise reject
time RCNC
flag
Read
only
1: Overflow
NORMAL, IDLE mode
DV1CK = 0
Noise reject circuit
RCSCK
Source clock Select
0
1
RPOLS
RCNF
Remote control signal polarity
0: Positive
select
1: Negative
Remote control signal monitor
0: Without noise
after noise rejctor
1: With noise
Note 1:
Reading out the register RCSR resets RCNF and RCOVF.
Note 2:
Source clock of timer/counter 3
DV1CK = 1
8
9
2 /fc
2 /fc
TC3CK
R/W
(Note 2)
Read
only
Note 3:
When a 5-bit up-down counter counts down to “0” after counting up, the RCNF defines to be noise.
Note 4:
fc: High-frequency clock [Hz], *: Don’t care.
Figure 2.7.7 Remote Control Rceive Control Register and Remote Control Receive Status Register
Table 2.7.4 Combination between The Polarity and The Edge Selection
RPOLS
TC3 Pin Input Pulse
(Interrupt occurrence is shown as allow.)
Measurement
0
1
Note:
When TC3CK is used in RCSCK, do not select an external clock to the TC3CK.
88CS38B-81
2007-09-12
88CS38B-82
RCNC
Writing RCCR
Reading RCSR
RCNF
RCOVF
RNCM
TC3 pin input
Up-down counter
Source clock
Reading RCSR
RCNF
RCOVF
RNCM
TC3 pin input
Up-down counter
Source clock
0
0
08H
1
1
3
3
4
1
2
1
0
1
2
1
(a) Noise (RPOLS = 0, RCNC = 03H)
0
(b) Noise rejection circuit overflow flag (RPOLS = 1, RCNC = 08H to 03H)
2
2
03H
0
0
Reset
Reset
TMP88CS38B/CM38B/CP38B
Figure 2.7.8 Remote Control Receive Circuit Timing Chart
2007-09-12
TMP88CS38B/CM38B/CP38B
2.8
8-Bit Timer/Counter 4 (TC4)
2.8.1
Configuration
TC4S
11
10
fc/2 or fc/2
7
8
fc/2 or fc/2
5
6
fc/2 or fc/2
3
4
fc/2 or fc/2
A
B
C
D
AS
Y
B
Clear
8-bit up counter
Y
TC4ES
TC4 pin
Source
clock
Overfolw
detect
Comparator
H
Match
detect
S
3
TC4S
TC4CK
TC4M
2
Note:
TC4CR
TC4DR
Timer/counter 4 control register
8-bit timer register 4
INTTC4
interrupt
request signal
Set the input/output control correctly for the substitutive input/output pins. For details, see the description of
the input/output port control register.
Figure 2.8.1 Timer/Counter 4 (TC4)
88CS38B-83
2007-09-12
TMP88CS38B/CM38B/CP38B
2.8.2
Control
The timer/counter 4 is controlled by a timer/counter 4 control register (TC4CR) and an
8-bit timer register 4 (TC4DR). Reset does not affect TC4DR.
TC4DR
(0001BH)
7
6
5
4
3
2
1
0
TC4CR
(0001CH)
7
6
5
4
3
2
1
0
Write only (Initial value: 1111 1111)
TC4S
TC4CK
TC4M
Write only (Initial value: **00 0000)
00: Timer/event counter mode
TC4S
01: Reserved
TC4 start control
10: Reserved
11: Reserved
NORMAL, IDLE mode
DV1CK = 0
TC4CK
TC4 source clock select [Hz]
(Note 4)
DV1CK = 1
11
fs/2
fc/2
7
fs/2
8
010
fc/2
5
fs/2
6
011
fc/2
3
fs/2
4
100
Reserved
Reserved
101
Reserved
Reserved
110
Reserved
Reserved
000
fc/2
001
111
12
R/W
External clock (TC4 pin input)
00: Timer/event counter mode
TC4M
01: Reserved
TC4 operating mode select
10: Reserved
11: Reserved
Note 1:
fc: High-frequency clock [Hz], *: Don’t care
Note 2:
Values to be loaded to the timer register must satisfy the following condition (1 ≤ TC4DR ≤ 255).
Note 3:
When the TC4 is started (TC4S = 0 → 1) or disabled (TC4S = 1 → 0) or while the TC4 is operating (TC4S =
1 → 1), do not write to TC4M and TC4CK in TC4CR. If these registers are selected/changed during these
operations, counting up is not performed properly.
Note 4:
When STOP mode is started, timer counter is stopped and cleared. Set TC4S to “1” after STOP mode is
released for restarting timer counter.
PMPXCR
(00027H)
TC4ES
Note 5:
Undefined values are read from bits 6 and 7 of TC4CR.
Note 6:
Do not change TC4DR while the TC4 is operating.
7
6
“0”
CHS
5
3
2
1
0
TC4ES (TC3ES) (Initial value: 00** **00)
TC4 edge select
Note 1:
4
0: Rising edge
1: Falling edge
Write
only
TC4CR, TC4DR and PMPXCR are write only register and must not be used with any of the
read-modify-write instructions such as SET, CLR, etc.
Figure 2.8.2 Timer Register 4 and TC4 Control Register
88CS38B-84
2007-09-12
TMP88CS38B/CM38B/CP38B
2.8.3
Function
The timer/counter 4 has two operating modes: timer, event counter mode.
(1) Timer mode
In this mode, the internal clock is used for counting up. The contents of TC4DR are
compared with the contents of up counter. If a match is found, an INTTC4 interrupt is
generated and the up counter is cleared to “0”. Counting up resumes after the up
counter is cleared.
Table 2.8.1 Source Clock (Internal clock) for Timer/Counter 4 (Example: at fc = 16.0 MHz)
NORMAL, IDLE mode
DV1CK = 0
TC4CK
Resolution [μs]
DV1CK = 1
Maximum Setting
Time [ms]
Resolution [μs]
Maximum Setting
Time [ms]
000
128.0
32.6
256.0
65.3
001
8.0
2.0
16.0
4.1
010
2.0
0.510
4.0
1.0
100
0.5
0.128
1.0
0.255
(2) Event counter mode
In this mode, the TC4 pin input (External clock) pulse is used for counting up. Either
the rising or falling edge can be selected with TC4ES (Bit1 PMPXCR). The contents of
TC4DR are compared with the contents of the up counter. If a match is found, an
INTTC4 interrupt is generated and the counter is cleared. The maximum applied
frequency is shown Table 2.8.2. Two or more machine cycles are required for both the
high and low level of the pulse width.
Note:
The event counter mode can only be used in NORMAL or IDLE mode.
Table 2.8.2 Timer/Counter 4 External Clock Source
Minimum Input Pulse Width [s]
NORMAL1, IDLE1 Mode
3
“H” Width
2 /fc
“L” Width
2 /fc
3
88CS38B-85
2007-09-12
TMP88CS38B/CM38B/CP38B
2.9
Serial Bus Interface (SBI-ver. D)
The TMP88CS38B and TMP88CM38B/CP38B has a 1-channel serial bus interface which
employs a clocked-synchronous 8-bit serial bus interface and an I2C bus (a bus system by
Philips). The serial bus interface pins are selectively used as either channel 0 or channel 1.
The serial interface is connected to external devices through P35 (SDA0)/P52 (SDA1) and P34
(SCL0)/P51 (SCL1) in the I2C bus mode; and through P53 ( SCK1 ), P52 (SO1) and P51 (SI1) in
the clocked-synchronous 8-bit SIO mode.
The serial bus interface pins are also used for the P3/P5 port. When used for serial bus
interface pins, set the P3/P5 output latches of these pins to “1”. When not used as serial bus
interface pins, the P3/P5 port is used as a normal I/O port.
Note 1: When P3 and P5 is used as serial bus interface pins, P35, P34, P51 and P50 should be set
as a sink open-drain output by clearing PSELCR to “0”.
Note 2: The I2C of TMP88CS38B and TMP88CM38B/CP38B can be used only in the standard mode
of I2C. The fast mode and the high speed mode can not be used.
2.9.1
Configuration
INTSBI interrupt request
SCL
SCK
SIO
clock
control
fc/2
fc/4
Source clock
generator
P52
Input/
(SDA1/SO1)
output
P51
control
(SCL1/SI1)
Divider
I C bus
clock
sync.
+
Control
SBI control register B/
SBI status register
I2CAR
2
I C bus
address register
SBIDBR
SBI data
buffer register
SI
2
I C bus
data
control
Shift
register
SBICRB/
SBISR
SO
SIO
data control
Transfer
control
circuit
2
Noise
canceller
P53
( SCK )
Noise
canceller
SDA
P35
(SDA0)
P34
(SCL0)
SBICRA
SBI control register A
Figure 2.9.1 Serial Bus Interface (SBI)
88CS38B-86
2007-09-12
TMP88CS38B/CM38B/CP38B
2.9.2
Control
The following registers are used for control the serial bus interface and monitor the
operation status.
• Serial bus interface control register A (SBICRA)
•
Serial bus interface control register B (SBICRB)
•
Serial bus interface data buffer register (SBIDBR)
•
I2C bus address register (I2CAR)
•
Serial bus interface status register A (SBISRA)
•
Serial bus interface status register B (SBISRB)
•
Serial clock source control register (SCCRB)
•
Serial clock control status register (SCSR)
The above registers differ depending on a mode to be used. Refer to section 2.9.7 “I2C Bus
Mode Control” and 2.9.9 “Clocked-synchronous 8-Bit SIO Mode Control”.
2.9.3
Serial Clock Source Control
A serial bus interface circuit can reduce the power consumption by stopping a serial clock
generater.
Serial Clock Source Control Register
SCCRB
(00FF1H)
7
6
5
4
3
2
1
0
SCEN
(Initial value: 0*** ****)
SCEN
Note:
Serial clock source control
0: Do not generate source clock
Write
only
1: Generate source clock
When SCRQ and SCEN are “1”, SCEN cannot be cleared to “0”. When SCRQ is “0”, SCEN is cleared to “0”.
Serial Clock Control Status Register
SCSR
(00FF1H)
7
6
5
4
3
2
1
0
SCRQ
SCRQ
(Initial value: 0*** ****)
Serial clock source request
0: No source clock request from serial bus interface
1: Source clock request from serial bus interface
Read
only
SCRQ
SCEN
Source clock
Clock generation
“1” → SCEN Write data except
“00” to SBIM
Write data
“0” → SCEN
“00” to SBIM
Figure 2.9.2 Serial Clock Source
88CS38B-87
2007-09-12
TMP88CS38B/CM38B/CP38B
2.9.4
Channel Select
A serial bus interface circuit can select I/O pin when a serial bus interface is used for I2C
bus mode.
Port Switching Register
PMPXCR
(00027H)
7
6
5
“0”
CHS
4
3
1
0
(TC4ES) (TC3ES) (Initial value: 00** **00)
0: Channel 0
2
I C bus Channel Select
CHS
2
R/W
1: Channel 1
Note 1:
When SIO mode, don’t use channel 0. Therefore, set to “1” in PMPXCR at SIO mode.
Note 2:
Always write “0” to bit7 in PMPXCR.
Note 3:
*: Don’t care
Figure 2.9.3 Channel Select
2.9.5
Software Reset
A serial bus interface circuit has a software reset function, when a serial bus interface
circuit is locked by an external noise, etc.
To occur software reset, write “01”, “10” into the SWRST (Bit1, 0 in SBICRB). During
software reset, the SWRMON (Bit0 in SBISRA) is clear to “0”.
2.9.6
The Data Format in The I2C bus Mode
The data format when using the TMP88CS38B and TMP88CM38B/CP38B in the I2C bus
mode are shown in as below.
(a) Addressing format
8 bits
S
Slave address
1
R A
/ C
W K
1 to 8 bits
Data
1
A
C
K
1 to 8 bits
Data
1
A
C P
K
1 or more
1
(b) Addressing format (with restart)
8 bits
S
Slave address
1
R A
/ C
W K
1 to 8 bits
Data
1
A
C S
K
8 bits
Slave address
1 or more
1
1
R A
/ C
W K
1 to 8 bits
Data
1
A
C P
K
1 or more
1
(c) Free data format
8 bits
S
Data
1
S:
1
A
C
K
1 to 8 bits
Data
1
A
C
K
1 to 8 bits
Data
1
A
C P
K
1 or more
Start condition
R/ W : Direction bit
ACK: Acknowledge bit
P:
Stop condition
Figure 2.9.4 Data Format in I2C Bus Mode
88CS38B-88
2007-09-12
TMP88CS38B/CM38B/CP38B
2.9.7
I2C Bus Mode Control
The following registers are used to control the serial bus interface (SBI) and monitor the
operation status in the I2C bus mode.
Serial Bus Interface Control Register A
SBICRA
(00020H)
7
6
5
BC
4
3
2
ACK
Acknowledgement mode
specification
(Initial value: 0000 *000)
ACK = 0
Number of
Bits
clock
8
8
1
1
2
2
3
3
4
4
5
5
6
6
7
7
Master mode
ACK = 1
Number of
Bits
clock
9
8
2
1
3
2
4
3
5
4
6
5
7
6
8
7
Slave mode
0
Not generate a clock
pulse for an
acknowledgement.
Not count a clock pulse
for an acknowledgement.
1
Generate a clock pulse
for an
acknowledgement.
Count a clock pulse for
an acknowledgement.
000
001
010
011
100
101
110
111
ACK
Number of transferred bits
ACK
0
SCK
BC
BC
1
Write
only
R/W
DV1CK = 0
DV1CK = 1
000: Reserved
(Note 3)
000: Reserved (Note 3)
001: Reserved
(Note 3)
001: Reserved (Note 3)
010:
Reserved
(Note
3)
010:
58.8 kHz
Serial clock selection
Write
SCK
011: 60.6 kHz
011: 30.3 kHz
(At fc = 16 MHz, output on SCL pin)
only
100: 30.7 kHz
100: 15.4 kHz
101: 15.5 kHz
101:
7.7 kHz
110:
7.8 kHz
110:
3.9 kHz
111 : Reserved
111 : Reserved
Note 1: Set the BC to “000” before switching to 8-bit SIO bus mode.
Note 2: SBICRA cannot be used with any of read-modify-write instructions such as bit manipulation, etc.
Note 3: This I2C bus circuit does not support the Fast mode. It supports the Standard mode only. Although
the I2C bus circuit itself allows the setting of a baud rate over 100 kbps, the compliance with the I2C
specification is not guaranteed in that case.
Serial Bus Interface Data Buffer Register
SBIDBR
(00021H)
7
6
5
4
3
2
1
0
(Initial value: **** ****)
Note 1:
Note 2:
R/W
For writing transmitted data, start from the MSB (Bit7).
The data which was written into SBIDBR cannot be read, since a write data buffer and a read buffer are
independent in SBIDBR. Therefore, SBIDBR cannot be used with any of read-modify-write instructions
such as bit manipulation, etc.
2
I C bus Address Register
I2CAR
(00022H)
7
6
SA6
SA5
5
4
3
Slave address
SA4
SA3
SA2
2
1
SA1
SA0
0
ALS
(Initial value: 0000 0000)
SA
Slave address selection
Write
Address recognition mode
0: Slave address recognition
only
ALS
specification
1: Non slave address recognition
Note 1: I2CAR is write-only register and cannot be used with any of read-modify-write instruction such as bit
manipulation, etc.
Note 2: Do not set I2CAR to “00H” to avoid the incorrect response of acknowledgment in slave mode. If “00H” is set
to I2CAR as the slave address and received “01H” in slave mode, the device might transmit the
acknowledgement incorrectly.
Figure 2.9.5 Serial Bus Interface Control Register A, Serial Bus Interface Data Buffer Register
and I2C Bus Address Register In The I2C Bus Mode
88CS38B-89
2007-09-12
TMP88CS38B/CM38B/CP38B
Serial Bus Interface Control Register B
SBICRB
(00023H)
7
6
5
4
MST
TRX
BB
PIN
MST
TRX
BB
PIN
SBIM
3
2
SBIM
0:
1:
0:
Transmitter/receiver selection
1:
0:
Start/stop generation
1:
0:
Cancel interrupt service request
1:
00:
01:
Serial bus interface operating
mode selection
10:
11:
Master/slave selection
SWRST1
Software reset start bit
SWRST0
1
0
SWRST1SWRST0
(Initial value: 0001 0000)
Slave
Master
Receiver
Transmitter
Generate a stop condition when MST, TRX and PIN are “1”.
Generate a start condition when MST, TRX and PIN are “1”.
Write
−
only
Cancel interrupt service request
Port mode (Serial bus interface output disable)
Clocked synchronous 8-bit SIO mode
2
I C bus mode
Reserved
Software reset starts by first writing “10” and next writing “01”.
Note 1:
Switch a mode to port after confirming that the bus is free.
Note 2:
Switch a mode to I C bus mode or clock synchronous 8-bit SIO mode after confirming that the port is high
2
level.
Note 3:
SBICRB has write-only register and must not be used with any of read-modify-write instructions such as bit
manipulation, etc.
Note 4:
When the SWRST (Bit1, 0 in SBICRB) is written to “01”, “10”, software reset (Four machine cycles) is
occurred.
This time, control the serial bus interface and monitor the operation status registers except the SBIM (Bit3,
2 in SBICRB) and the CHS (Bit6 in PMPXCR) are reseted.
Control the serial bus interface and monitor the operation status registers are SBICRA, SBICRB, SBIDBR,
I2CAR, SBISRA, SBISRB, SCCRA and SCSR.
Serial Bus Interface Status Register A
7
6
5
SBISRA
(00020H)
4
3
2
1
0
SWR
MON
ACK
(Initial value: **** ***1)
0: During software reset
SWRMON Software reset monitor
Read
only
1: − (Initial)
*: Don’t care
Serial Bus Interface Status Register B
SBISRB
(00023H)
7
6
5
4
3
2
1
0
MST
TRX
BB
PIN
AL
AAS
AD0
LRB
MST
Master/Slave selection status
monitor
0: Slave
TRX
Transmitter/Receiver selection
status monitor
0: Receiver
BB
Bus status monitor
PIN
Interrupt service requests
status monitor
(Initial value: 0001 0000)
1: Master
1: Transmitter
0: Bus free
1: Bus busy
0: Requesting interrupt service
1: Releasing interrupt service request
Arbitration lost detection
monitor
0: −
AAS
Slave address match detection
monitor
0: Not detect slave address match or “GENERAL CALL”
AD0
“GENERAL CALL” detection
monitor
0: Not detect “GENERAL CALL”
LRB
Last Received bit monitor
AL
Read
only
1: Arbitration lost detected
1: Detect slave address match or “GENERAL CALL”
1: Detect “GENERAL CALL”
0: Last receive bit is “0”
1: Last receive bit is “1”
Figure 2.9.6 Serial Bus Interface Control Register B and Serial Bus Interface
Status Register A/B in the I2C Bus Mode
88CS38B-90
2007-09-12
TMP88CS38B/CM38B/CP38B
(1) Acknowledgement mode specification
a.
Acknowledgement mode (ACK = “1”)
To set the device as an acknowledgement mode, the ACK (bit4 in SBICRA)
should be set to “1”. When a serial bus interface circuit is a master mode, an
additional clock pulse is generated for an acknowledge signal. In a slave mode, a
clock is counted for the acknowledge signal.
In the master transmitter mode, the SDA pin is released in order to receive an
acknowledge signal from the receiver during additional clock pulse cycle. In the
master receiver mode, the SDA pin is set to low level generation an acknowledge
signal during additional clock pulse cycle.
In a slave mode, when a received slave address matches to a slave address
which is set to the I2CAR or when a “GENERAL CALL” is received, the SDA pin is
set to low level generating an acknowledge signal. After the matching of slave
address or the detection of “GENERAL CALL”, in the transmitter the SDA pin is
released in order to receive an acknowledge signal from the receiver during
additional clock pulse cycle. In a receiver, the SDA pin is set to low level
generation an acknowledge signal during additional clock pulse cycle after the
matching of slave address or the detection of “GENERAL CALL”.
The Table 2.9.1 shows the SCL and SDA pins status in acknowledgement mode.
Table 2.9.1 SCL and SDA Pins Status in Acknowledgement Mode
Mode
Pin
Transmitter
SCL
Master
An additional clock pulse is generated.
Released in order to receive
and acknowledge signal.
SDA
SCL
Slave
b.
SDA
Receiver
Set to low level generating an
acknowledge signal.
A clock is counted for the acknowledge signal.
When slave address
matches or a general
call is detected
−
Set to low level generating an
acknowledge signal.
After matching of slave
address or general call
Released in order to receive
an acknowledge signal.
Set to low level generating an
acknowledge signal.
Non-acknowledgement mode (ACK = “0”)
To set the device as a non-acknowledgement mode, the ACK should be cleared to
“0”. In the master mode, a clock pulse for an acknowledge signal is not generated.
In the slave mode, a clock for a acknowledge signal is not counted.
(2) Number of transfer bits
The BC (bits 7 to 5 in SBICRA) is used to select a number of bits for next
transmitting and receiving data.
Since the BC is cleared to “000” as a start condition, a slave address and direction bit
transmissions are always executed in 8 bits. Other than these, the BC retains a
specified value.
88CS38B-91
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) Serial clock
a.
Clock source
The SCK (bits 2 to 0 in SBICRA) is used to select a maximum transfer frequency
output from the SCL pin in the master mode. Set a communication baud rate that
meets the I2C bus specification, such as the shortest pulse width of tLOW, based
on the equations shown below.
Four or more machine cycles are required for both high and low levels of pulse
width in the external clock which is input from SCL pin.
Note: Since the I2C of TMP88CS38B AND TMP88CM38B/CP38B can not be used
as the Fast mode and the High Speed mode, do not set SCK as the frequency
that is over 100 kHz.
This I2C bus circuit does not support high-speed mode, it supports standard mode only.
Set the baud rates, which have been calculated according to the formula below, to meet
the specifications of the I2C bus, such as the smallest pulse width of tLOW,
tHIGH
tLOW
1/fscl
tLOW = 2 /fc
n
n
SCK
(Bits 2 to 0 in the SBICRA)
DV1CK = 0
DV1CK = 1
000
001
010
011
100
101
110
4
5
6
7
8
9
10
5
6
7
8
9
10
11
tHIGH = 2 /fc + 8/fc
n
fscl = 1/(tLow + tHIGH)
fc: High-frequency clock
Figure 2.9.7 Clock Source
b.
Clock synchronization
In the I2C bus mode, in order to drive a bus with a wired AND, a master device
which pulls down a clock pulse to low will, in the first place, invalidate a clock
pulse of another master device which generates a high-level clock pulse.
The serial bus interface circuit has a clock synchronization function. This
function ensures normal transfer even if there are two or more masters on the
same bus.
The example explains clock synchronization procedures when two masters
simultaneously exist on a bus.
SCL pin (Master 1)
SCL pin (Master 2)
wait
Count start
Count reset
Count reset
SCL (Bus)
a
b
c
Figure 2.9.8 Clock Synchronization
As master 1 pulls down the SCL pin to the low level at point “a”, the SCL line of
the bus becomes the low level. After detecting this situation, master 2 resets
counting a clock pulse in the high level and sets the SCL pin to the low level.
88CS38B-92
2007-09-12
TMP88CS38B/CM38B/CP38B
Master 1 finishes counting a clock pulse in the low level at point “b” and sets the
SCL pin to the high level. Since master 2 holds the SCL line of the bus at the low
level, master 1 waits for counting a clock pulse in the high level. After master 2
sets a clock pulse to the high level at point “c” and detects the SCL line of the bus
at the high level, master 1 starts counting a clock pulse in the high level. Then,
the master, which has finished the counting a clock pulse in the high level, pulls
down the SCL pin to the low level.
The clock pulse on the bus is deteminded by the master device with the shortest
high-level period and the master device with the longest low-level period from
among those master devices connected to the bus.
(4) Slave address and address recognition mode specification
When the serial bus interface circuit is used with an addressing format to recognize
the slave address, clear the ALS (Bit0 in I2CAR) to “0”, and set the SA (Bits 7 to 1 in
I2CAR) to the slave address.
When the serial bus interfac circuit is used with a free data format not to recognize
the slave address, set the ALS to “1”. With a free data format, the slave address and the
direction bit are not recognized, and they are processed as data from immediately after
start condition.
(5) Master/slave selection
To set a master device, the MST (Bit7 in SBICRB) should be set to “1”. To set a slave
device, the MST should be cleared to “0”.
When a stop condition on the bus or an arbitration lost is detected, the MST is
cleared to “0” by the hardware.
(6) Transmitter/receiver selection
To set the device as a transmitter, the TRX (Bit6 in SBICRB) should be set to “1”. To
set the device as a receiver, the TRX should be cleared to “0”. When data with an
addressing format is transferred in the slave mode, the TRX is set to “1” by a hardware
if the direction bit (R/ W ) sent from the master device is “1”, and is cleared to “0” by a
hardware if the bit is “0. In the master mode, after an acknowledge signal is returned
from the slave device, the TRX is cleared to “0” by a hardware if a transmitted direction
bit is “1”, and is set to “1” by a hardware if it is “0”. When an acknowledge signal is not
returned, the current condition is maintained.
When a stop condition on the bus or an arbitration lost is detected, the TRX is
cleared to “0” by the hardware. The following table show TRX changing conditions in
each mode and TRX value after changing.
Mode
Direction Bit
Conditions
TRX after Changing
Slave
mode
“0”
A received slave address is the
same value set to I2CAR
“0”
“1”
Master
mode
“1”
“0”
ACK signal is returned
“1”
“1”
“0”
When a serial bus interface circuit operates in the free data format, a slave address
and a direction bit are not recognized. They are handled as data just after generating a
start condition. The TRX is not changed by a hardware.
88CS38B-93
2007-09-12
TMP88CS38B/CM38B/CP38B
(7) Start/stop condition generation
When the BB (Bit5 in SBICRB) is “0”, a slave address and a direction bit which are
set to the SBIDBR are output on a bus after generating a start condition by writing “1”
to the MST, TRX, BB and PIN. It is necessary to set transmitted data to the SBIDBR
and set “1” to ACK beforehand.
SCL pin
1
2
3
4
5
6
7
8
SDA pin
A6
A5
A4
A3
A2
A1
A0
R/ W
slave address and the direction bit
Start
condition
9
Acknowledge
signal
Figure 2.9.9 Start Condition Generation and Slave Address Generation
When the BB is “1”, sequence of generating a stop condition is started by writeng “1”
to the MST, TRX and PIN, and “0” to the BB. Do not modify the contents of MST, TRX,
BB and PIN until a stop condition is generated on a bus.
SCL pin
SDA pin
Stop condition
Figure 2.9.10 Stop Condition Generation
When a stop condition is generated and the SCL line on a bus is pulled down to low
level by another device, a stop condition is generated after releasing the SCL line.
The bus condition can be indicated by reading the contents of the BB (Bit5 in
SBISRB). The BB is set to “1” when a start condition on a bus is detected and is cleared
to “0” when a stop condition is detected.
(8) Interrupt service request and cancel
When a serial bus interface circuit is in the master mode and transferring a number
of clocks set by the BC and the ACK is complete, a serial bus interface interrupt
request (INTSBI) is generated.
In the slave mode, the conditions of generating INTSBI are follows:
•
At the end of acknowledge signal when the received slave address matches to the
value set by the I2CAR
•
At the end of acknowledge signal when a “GENERAL CALL” is received
•
At the end of transferring or receiving after matching of slave address or receiving
of “GENRAL CALL”
When a serial bus interface interrupt request occurs, the PIN (Bit4 in SBISR) is
cleared to “0”. During the time that the PIN is “0”, the SCL pin is pulled down to low
level.
Either writing data to SBIDBR or reading data from the SBIDBR sets the PIN to “1”.
The time from the PIN being set to “1” until the SCL pin is released takes tLOW.
Although the PIN (Bit4 in SBICRB) can be set to “1” by the program, the PIN can not
be cleared to “0” by the program.
Note:
If the arbitration lost occurs, when the slave address does not match, the PIN is not
cleared to “0” even thought INTSBI is generated.
88CS38B-94
2007-09-12
TMP88CS38B/CM38B/CP38B
(9) Serial bus interface operating mode selection
The SBIM (Bit3 and 2 in SBICRB) is used to specify a serial bus interface operation
mode.
Set the SBIM to “10” in order to change a operation mode to I2C bus mode. Before
changing operation mode, confirm serial bus interface pins in a high level. And switch
a mode to port after confirming that a bus is free.
(10) Arbitration lost detection monitor
Since more than one master device can exist simultaneously on a bus in the I2C bus
mode, a bus arbitration procedure is implemented in order to guarantee the contents of
transferred data.
Data on the SDA line is used for bus arbitration of the I2C bus.
The following shows an example of a bus arbitration procedure when two master
devices exist simultaneously on a bus. Master 1 and master 2 output the same data
until point “a”. After master 1 outputs “1” and master 2, “0”, the SDA line of a bus is
wired AND and the SDA line is pulled-down to the low level by master 2. When the
SCL line of a bus is pulled up at point “b”, the slave device reads data on the SDA line,
that is data in master 2.
Data transmitted from master 1 becomes invalid. The state in master 1 is called
“arbitration lost”. A master device which loses arbitration releases the SDA pin and
the SCL pin in order not to effect data transmitted from other masters with arbitration.
When more than one master sends the same data at the first word, arbitration occurs
continuously after the second word.
SCL (Bus)
SDA pin (Master 1)
SDA pin becomes “1” after losing arbitration.
SDA pin (Master 2)
SDA (Bus)
a
b
Figure 2.9.11 Arbitration Lost
88CS38B-95
2007-09-12
TMP88CS38B/CM38B/CP38B
The serial bus interface circuit compares levels of a SDA line of a bus with its those
SDA pin at the rising edge of the SCL line. If the levels are unmatched, arbitration is
lost and the AL (Bit3 in SBISRB) is set to “1”.
When the AL is set to “1”, the MST and TRX are cleared to “0” and the mode is
switched to a slave receiver mode.
The AL is cleared to “0” by writing or reading data to or from the SBIDBR or writing
data to the SBICRB.
SCL pin
1
2
3
4
5
6
7
8
SDA pin
D7A
D6A
D5A
D4A
D3A
D2A
D1A
D0A
SCL pin
1
2
3
4
5
6
7
8
9
1
2
3
D7A’
D6A’
D5A’
Master
A
Master
B
9
Stop clock output
SDA pin
D7B
D6B
Releasing SDA pin and SCL pin to high level as losing arbitration.
AL
MST
TRX
Accessed to
SBIDBR or SBICRB
INTSBI
Figure 2.9.12 Example of when a Serial Bus Interface Circuit is a Master B
(11) Slave address match detection monitor
In the slave mode, the AAS (Bit2 in SBISR) is set to “1” when the received data is
“GENERAL CALL” or the received data matches the slave address setting by I2CAR
with an address recognition mode (ALS = 0).
When a serial bus interface circuit operates in the free data format (ALS = 1), the
AAS is set to “1” after receiving the first 1-word of data.
The AAS is cleared to “0” by writing data to the SBIDBR or reading data from the
SBIDBR.
(12) GENERAL CALL detection monitor
The AD0 (Bit1 in SBISR) is set to “1” when all 8-bit received data is “0” immediately
after a start condition in a slave mode. The AD0 is cleared to “0” when a start or stop
condition is detected on a bus.
(13) Last received bit monitor
The SDA value stored at the rising edge of the SCL is set to the LRB (Bit0 in
SBISRB). In the acknowledge mode, immediately after an INTSBI interrupt request is
generated, an acknowledge signal is read by reading the contents of the LRB.
88CS38B-96
2007-09-12
TMP88CS38B/CM38B/CP38B
2.9.8
Data Transfer of I2C Bus
(1) Device initialization
For initialization of device, set the ACK in SBICRA to “1” and the BC to “000”.
Specify the data length to 8 bits to count clocks for an acknowledge signal. Set a
transfer frequency to the SCK in SBICRA.
Next, set the slave address to the SA in I2CAR and clear the ALS to “0” to set an
addressing format.
After confirming that the serial bus interface pin is high level, for specifying the
default setting to a slave receiver mode, clear “0” to the MST, TRX and BB in SBICRB,
set “1” to the PIN, “10” to the SBIM, and “00” to bits SWRST1 and SWRST0.
Note:
The initialization of a serial bus interface circuit must be complete within the time
from all devices which are connected to a bus have initialized to and device does
not generate a start condition. If not, the data can not be received correctly because
the other device starts transferring before an end of the initialization of a serial bus
interface circuit.
(2) Start condition and slave address generation
Confirm a bus free status (when BB = 0).
Set the ACK to “1” and specify a slave address and a direction bit to be transmitted to
the SBIDBR.
By writing “1” to the MST, TRX, BB and PIN, the start condition is generated on a
bus and then, the slave address and the direction bit which are set to the SBIDBR are
output. An INTSBI interrupt request occurs at the 9th falling edge of a SCL clock cycle,
and the PIN is cleared to “0”. The SCL pin is pulled down to the low level while the PIN
is “0”. When an interrupt request occurs the TRX changes by the hardware according
to the direction bits only when an acknowledge signal is returned from the slave device.
Note 1: Do not write a slave address to be output to the SBIDBR while data is transferred. If
data is written to the SBIDBR, data to been outputting may be destroyed.
Note 2: The bus free must be confirmed by software within 98.0 μs (the shortest
transmitting time according to the I2C bus standard) after setting of the slave
address to be output. Only when the bus free is confirmed, set “1” to the MST, TRX,
BB, and PIN doesn’t finish within 98.0 μs, the other masters may start the
transferring and the slave address data written in SBIDBR may be broken.
SCL pin
1
2
3
4
5
6
7
8
SDA pin
A6
A5
A4
A3
A2
A1
A0
R/ W
Start condition
Slave address + direction bit
9
Acknowledge
signal from a
slave device
PIN
INTSBI
interrupt
request
Figure 2.9.13 Start Condition Generation and Slave Address Transfer
88CS38B-97
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) 1-word data transfer
Check the MST by the INTSBI interrupt process after an 1-word data transfer is
completed, and determine whether the mode is a master or slave.
a.
When the MST is “1” (Master mode)
Check the TRX and determine whether the mode is a transmitter or receiver.
1.
When the TRX is “1” (Transmitter mode)
Test the LRB. When the LRB is “1”, a receiver does not request data. Implement
the process to generate a stop condition (Described later) and terminate data
transfer.
When the LRB is “0”, the receiver requests next data. When the next
transmitted data is other than 8 bits, set the BC, set the ACK to “1”, and write the
transmitted data to the SBIDBR. After writing the data, the PIN becomes “1”, a
serial clock pulse is generated for transferring a next 1 word of data from the SCL
pin, and then the 1-word data is transmitted. After the data is transmitted, and
an INTSBI interrupt request occurs. The PIN become “0” and the SCL pin is set to
low level. If the data to be transferred is more than one word in length, repeat the
procedure from the LRB test above.
Write to SBIDBR
SCL pin
1
2
3
4
5
6
7
8
SDA pin
D7
D6
D5
D4
D3
D2
D1
D0
9
Acknowledge
signal from a
receiver
PIN
INTSBI interrupt
request
Figure 2.9.14 Example of when BC = “000”, ACK = “1”
2.
When the TRX is “0” (Receiver mode)
When the next transmitted data is other than of 8 bits, set the BC again. Set the
ACK to “1” and read the received data from the SBIDBR (Reading data is
undefined immediately after a slave address is sent). After the data is read, the
PIN becomes “1”. A serial bus interface circuit outputs a serial clock pulse to the
SCL to transfer next 1 word of data and sets the SDA pin to “0” at the
acknowledge signal timing.
An INTSBI interrupt request occurs and the PIN becomes “0”. Then a serial bus
interface circuit outputs a clock pulse for 1 word of data transfer and the
acknowledge signal each time that received data is read from the SBIDBR.
Read to SBIDBR
SCL pin
1
2
3
4
5
6
7
8
SDA pin
D7
D6
D5
D4
D3
D2
D1
D0
PIN
9
New D7
Acknowledge
signal to a
transmitter
INTSBI interrupt
Figure 2.9.15 Example of when BC = “000”, ACK = “1”
88CS38B-98
2007-09-12
TMP88CS38B/CM38B/CP38B
To make the transmitter terminate transmit, clear the ACK to “0” before
reading data which is 1 word before the last data to be received. A serial bus
interface circuit does not generate a clock pulse for the acknowledge signal by
clearing ACK. In the interrupt routine of end of transmission, when the BC is set
to “001” and read the data, PIN is set to “1” and generates a clock pulse for a 1-bit
data transfer. In this case, since the master device is a receiver, the SDA line on a
bus keeps the high level. The transmitter receives the high-level signal as an ACK
signal. The receiver indicates to the transmitter that data transfer is complete.
After 1-bit data is received and an interrupt request has occurred, generates the
stop condition to terminate data transter.
SCL pin
1
2
3
4
5
6
7
8
SDA pin
D7
D6
D5
D4
D3
D2
D1
D0
1
Acknowledge signal
sent to a transmitter
PIN
INTSBI interrupt
request
“001” → BC
Read SBIDBR
“0” → ACK
Read SBIDBR
Figure 2.9.16 Termination of Data Transfer in Master Receiver Mode
b.
When the MST is “0” (Slave mode)
In the slave mode, a serial bus interface circuit operates either in normal slave
mode or in slave mode after losing arbitration.
In the slave mode, the conditions of generating INTSBI are follows:
•
When the received slave address matches to the value set by the I2CAR
•
When a “GENERAL CALL” is received
•
At the end of transferring or receiving after matching of slave address or
receiving of “GENERAL CALL”
A serial bus interface circuit changes to a slave mode if arbitration is lost in the
master mode. And an INTSBI interrupt request occurs when word data transfer
terminates after losing arbitration. The behavior of INTSBI and PIN after losing
arbitration are shown in Table 2.9.2.
Table 2.9.2 The Behavior of INTSBI and PIN after Losing Arbitration
When the arbitration occurs during transmission
of slave address as a master
INTSBI
PIN
When the arbitration occurs during transmission
of data as a master transmit mode
INTSIB is generated at the terminatin of word data.
When the slave address matches the value set by
I2CAR, the PIN is cleared to “0” by generating of
INTSBI. When the slave address doesn’t match
the value set by I2CAR, the PIN keeps “1”.
PIN keeps “1”.
Check the AL (Bit3 in the SBISR), the TRX (Bit6 in the SBISR), the AAS (Bit2
in the SBISR), and the AD0 (Bit1 in the SBISR) and implements processes
according to conditions listed in Table 2.9.3.
88CS38B-99
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.9.3 Operation in the Slave Mode
TRX
AL
AAS
AD0
Conditions
Process
1
1
1
0
A serial bus interface circuit loses arbitration
when transmitting a slave address. And
receives a slave address of which the value
of the direction bit sent from another master
is “1”.
Set the number of bits in 1 word to the BC
and write transmitted data to the SBIDBR.
0
1
0
In the slave receiver mode, a serial bus
interface circuit receives a slave address of
which the value of the direction bit sent from
the master is “1”.
0
0
In the slave transmitter mode, 1-word data is
transmitted.
Test the LRB. If the LRB is set to “1”, set the
PIN to “1” since the receiver does not
request next data. Then, clear the TRX to “0”
release the bus. If the LRB is set to “0”, set
the number of bits in 1 word to the BC and
write transmitted data to the SBIDBR since
the receiver requests next data.
1
1/0
A serial bus interface circuit loses arbitration
when transmitting a slave address. And
receives a slave address of which the value
of the direction bit sent from another master
is “0” or receives a “GENERAL CALL”.
Read the SBIDBR for setting the PIN to “1”
(Reading dummy data) or write “1” to the
PIN.
0
0
A serial bus interface circuit loses arbitration
when transmitting a slave address or data.
And terminates transferring word data.
A serial bus interface circuit is changed to
slave mode. To clear AL to “0”, read the
SBIDBR or write the data to SBIDBR.
1
1/0
In the slave receiver mode, a serial bus
interface circuit receives a slave address of
which the value of the direction bit sent from
the master is “0” or receives “GENERAL
CALL”.
Read the SBIDBR for setting the PIN to “1”
(Reading dummy data) or write “1” to the
PIN.
0
1/0
In the slave receiver mode, a serial bus
interface circuit terminates receiving of
1-word data.
Set the number of bits in 1 word to the BC
and read received data from the SBIDBR.
0
1
0
Note:
In the slave mode, if the slave address set in I2CAR is “00000000B”, the TRX
changes to “1” by receiving the start byte data “00000001B”.
(4) Stop condition generation
When the BB is “1”, a sequence of generating a stop condition is started by setting “1”
to the MST, TRX, and PIN, and clear “0” to the BB. Do not modify the contents of the
MST, TRX, BB, PIN until a stop condition is generated on a bus.
When a SCL line on a bus is pulled down by other devices, a serial bus interface
circuit generates a stop condition after they release a SCL line.
“1” → MST
“1” → TRX
“0” → BB
“1” → PIN
Stop condition
SCL pin
SDA pin
PIN
BB (Read)
Figure 2.9.17 Stop Condition Generation
88CS38B-100
2007-09-12
TMP88CS38B/CM38B/CP38B
(5) Restart
Restart is used to change the direction of data transfer between a master device and
a slave device during transferring data. The following explains how to restart a serial
bus interface circuit.
Clear “0” to the MST, TRX and BB and set “1” to the PIN. The SDA pin retains the
high level and the SCL pin is released. Since a stop condition is not generated on a bus,
a bus is assumed to be in a busy state from other devices. Test the BB until it becomes
“0” to check that the SCL pin a serial bus interface circuit is released. Test the LRB
until it becomes “1” to check that the SCL line on a bus is not pulled down to the low
level by other devices. After confirming that a bus stays in a free state, generate a start
condition with procedure (2).
In order to meet setup time when restarting, take at least 4.7 μs of waiting time by
software from the time of restarting to confirm that a bus is free until the time to
generate a start condition.
Note:
When restarting after receiving in master receiver mode, because the divice doesn’t
send an acknowledgement as a last data, the level of SCL line can not be
conrirmied by reading LRB. Therefore, confirm the status of SCL line by reading
P5PRD register.
“0” → MST
“0” → TRX
“0” → BB
“1” → PIN
“1” → MST
“1” → TRX
“1” → BB
“1” → PIN
4.7 μs (Min)
Start condition
SCL (Bus)
SCL (Pin)
SDA (Pin)
LRB
BB
PIN
Figure 2.9.18 Timing Diagram when Restarting
88CS38B-101
2007-09-12
TMP88CS38B/CM38B/CP38B
2.9.9
Clocked-synchronous 8-Bit SIO Mode Control
The following registers are used to control the serial bus interface (SBI) and monitor the
operation in the clocked-synchronous 8-bit SIO mode.
Serial Bus Interface Control Register A
SBICRA
7
6
(00020H)
SIOS
SIOINH
SIOS
SIOINH
SIOM
SCK
Note 1:
Note 2:
Note 3:
5
4
SIOM
3
2
“0”
0:
1:
0:
1:
00:
01:
10:
11:
Indicate transfer start/stop
Continue/abort transfer
Transfer mode select
Serial clock selection
(At fc = 16 MHz, Output on SCK
pin)
1
0
(Initial value: 0000 *000)
SCK
Stop
Start
Continue transfer
Abort transfer (Automatically cleared after abort)
8-bit transmit mode
Reserved
8-bit transmit/receive mode
8-bit receive mode
DV1CK = 0
000: 1000.0 kHz
001: 500.0 kHz
010: 250.0 kHz
011: 125.0 kHz
100:
62.5 kHz
101:
31.2 kHz
110:
15.6 kHz
111: External clock (Input
from SCK pin)
DV1CK = 1
000: 500.0 kHz
001: 250.0 kHz
010: 125.0 kHz
011:
62.5 kHz
100:
31.2 kHz
101:
15.6 kHz
110:
7.8 kHz
111: External clock (Input
from SCK pin)
Write
only
fc: High-frequency clock [Hz], *: Don’t care
Clear the SIOS to “0” and set the SIOINH to “1” when setting the transfer mode and serial clock.
SBICRA is write-only register and cannot be used with any of read-modify-write instructions such as bit
manipulation, etc.
Serial Bus Interface Data Register
SBIDBR
7
6
5
4
3
2
1
0
(00021H)
(Initial value: **** ****)
Note1 :
R/W
The data which was written into SBIDBR cannot be read, since a write buffer and a read buffer are
independent in SBIDBR. Therefore, SBIDBR cannot be used with any of read-modify-write instructions
such as bit manipulation, etc.
Note 2: *: Don’t care
Serial Bus Interface Control Register B
SBICRB
7
6
5
4
(00023H)
“0”
“0”
“0”
“1”
SBIM
Serial bus interface operation
mode selection
SWRST1
Software reset start bit
SWRST0
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
3
2
SBIM
00:
01:
10:
11:
1
0
SWRST1 SWRST0
(Initial value: **** 0000)
Port mode (Serial bus interface output disable)
SIO mode
2
I C bus mode
Reserved
Write
only
Software reset starts by first writing “10” and next writing “01”
*: Don’t care
Switch a mode to port after data transfer is complete.
2
Switch a mode to I C bus mode or clock synchronous 8-bit SIO mode after confirming that the port is high
level.
SBICRB is a write-only register and cannot be used with any of read-modify-write instructions such as bit
manipulation, etc.
Clear bit7 to 5 in SBICRB to “0”, and set bit4 to “1”.
When the SWRST (Bit1, 0 in SBICRB) is written to “01”, “10”, software reset is occurred.
This time, control the serial bus interface and monitor the operation status registers except the SBIM (Bit3,
2 in SBICRB) and the CHS (Bit6 in PMPXCR) are reseted.
Control the serial bus interface and monitor the operation status registers are SBICRA, SBICRB, SBIDBR,
I2CAR, SBISRA, SBISRB, SCCRA, SCCRB and SCSR.
Figure 2.9.19 Control Register/Data Buffer Register/Status Register in SIO Mode (1)
88CS38B-102
2007-09-12
TMP88CS38B/CM38B/CP38B
Serial Bus Interface Status Register A
SBISRA
7
6
5
4
3
2
1
0
(00020H)
SWR
MON
SWRMON
(Initial value: **** ***1)
0: During software reset
Software reset monitor
Read
only
1: − (Initial)
Serial Bus Interface Status Register B
SBISRB
7
6
5
4
3
2
1
0
(00023H)
“1”
“1”
“1”
“1”
SIOF
SEF
“1”
“1”
SIOF
SEF
Note:
Serial transfer operating status
monitor
Shift operating status monitor
0: Transfer terminated
1: Transfer in process
Read
only
0: Shift operation terminated
1: Shift operation in process
Set bit7 to 4, bit1 and bit0 in SBISRB to “1”.
Figure 2.9.20 Control Register/Data Buffer Register/Status Register in SIO Mode (2)
(1) Serial clock
a.
Clock source
The SCK (Bits 2 to 0 in SBICRA) is used to select the following functions.
1.
Internal clock
In an internal clock mode, any of seven frequencies can be selected. The serial
clock is output to the outside on the SCK pin. The SCK pin becomes a high level
when data transfer starts. When writing (in the transmit mode) or reading (in the
receive mode) data cannot follow the serial clock rate, an automatic-wait function
is executed to stop the serial clock automatically and hold the next shift operation
until reading or writing is complete.
Automatic-wait function
SCK pin output
SO pin output
Write transmitted data
1
2
a0
a1
3
7
a 2 a5
a6
8
a7
a
1
2
b0
b1
b
6
7
8
1
2
3
b4 b5 b 6 b 7 c 0 c 1
c2
c
Figure 2.9.21 Automatic-wait Function
2.
External (SCK = “111”)
An external clock supplied to the SCK pin is used as the serial clock. In order to
ensure shift operation, a pulse width of at least 2-machine cycles is required for
both high and low levels in the serial clock. The maximum data transfer frequency
is 1MHz (fc = 16.0 MHz).
SCK pin
tSCKL tSCKH
tSCKL, tSCKH > 2 tcyc
Note: tcyc = 4/fc (in NORMAL mode, IDLE mode)
Figure 2.9.22 The Maximum Data Transfer Frequency in The External Clock Input
88CS38B-103
2007-09-12
TMP88CS38B/CM38B/CP38B
b.
Shift edge
The leading edge is used to transmit data, and the trailing edge is used to
receive data.
1.
Leading edge
Data is shifted on the leading edge of the serial clock (at a falling edge of the
SCK pin input/output).
2.
Trailing edge
Data is shifted on the trailing edge of the serial clock (at a rising edge of the
SCK pin input/output).
SCK pin
SO pin
Bit0
Shift register
Bit1
Bit2
76543210 *7654321 **765432
Bit3
Bit4
Bit5
Bit6
Bit7
***76543
****7654
*****765
******76
*******7
Bit5
Bit6
Bit7
(a) Leading edge
SCK pin
SI pin
Bit0
Shift register
********
Bit1
0*******
Bit2
10******
Bit3
210*****
Bit4
3210****
43210***
543210** 6543210* 76543210
(b) Trailing edge
*: Don’t care
Figure 2.9.23 Shift Edge
(2) Transfer mode
The SIOM (Bits 5 and 4 in SBICRA) is used to select a transmit, receive, or
transmit/receive mode.
a.
8-bit transmit mode
Set a control register to a transmit mode and write transmit data to the
SBIDBR.
After the transmit data is written, set the SIOS to “1” to start data transfer. The
transmitted data is transferred from the SBIDBR to the shift register and output
to the SO pin in synchronous with the serial clock, starting from the least
significant bit (LSB). When the transmit data is transferred to the shift register,
the SBIDBR becomes empty. The INTSBI (Buffer empty) interrupt request is
generated to request new data.
When the internal clock is used, the serial clock will stop and automatic-wait
function will be initiated if new data is not loaded to the data buffer register after
the specified 8-bit data is transmitted. When transmit new data is written,
automatic-wait function is canceled.
When the external clock is used, data should be written to the SBIDBR before
new data is shifted.
The SO pin is “1” from the time transmission starts until the first data bit is
sent. When SIOF becomes “0”, the shift register is cleared. So, output of an
undefined value is not prevented at the start of the next transmission.
The transfer speed is determined by the maximum delay time between the time
when an interrupt request is generated and the time when data is written to the
SBIDBR by the interrupt service program.
88CS38B-104
2007-09-12
TMP88CS38B/CM38B/CP38B
Transmitting data is ended by cleaning the SIOS to “0” by the buffer empty
interrupt service program or setting the SIOINH to “1”. When the SIOS is cleared,
the transmitted mode ends when all data is output. In order to confirm if data is
surely transmitted by the program, set the SIOF (Bit3 in the SBISRB) to be
sensed. The SIOF is cleared to “0” when transmitting is complete. When the
SIOINH is set, transmitting data stops. The SIOF turns “0”.
When the external clock is used, it is also necessary to clear the SIOS to “0”
before new data is shifted; otherwise, dummy data is transmitted and operation
ends.
Clear SIOS
SIOS
SIOF
SEF
SCK pin (Output)
SO pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
b5
b6
b7
INTSBI interrupt
request
SBIDBR
a
b
Write transmitted data
(a) Internal clock
Clear SIOS
SIOS
SIOF
SEF
SCK pin (Input)
SO pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
INTSBI interrupt
request
SBIDBR
a
b
Write transmitted data
(b) External clock
Figure 2.9.24 Transfer Mode
88CS38B-105
2007-09-12
TMP88CS38B/CM38B/CP38B
Example: Program to stop transmitting data. (When external clock is used.)
STEST1:
STEST2:
TEST
(SBISRB). SEF
JRS
F, STEST1
TEST
(P5). 3
JRS
T, STEST2
LD
(SBICRA), 00000111B
;
If SEF = 1 then loop
;
If SCK = 0 then loop
;
SIOS ← 0
SCK pin
SIOF
SO pin
Bit6
Bit7
tSODH = Min 3.5/fc [s] (in NORMAL mode, IDLE mode)
Figure 2.9.25 Transmitted Data Hold Time at End of Transmit
b.
8-bit receive mode
Set a control register to a receive mode and the SIOS to “1” for switching to a
receive mode.
Data is received from the SI pin to the shift register in synchronous with the
serial clock, starting from the least significant bit (LSB). When the 8-bit data is
received, the data is transferred from the shift register to the SBIDBR. The
INTSBI (Buffer full) interrupt request is generated to request of reading the
received data. The data is read from the SBIDBR by the interrupt service
program.
When the external clock is used, since shift operation is synchronized with the
clock pulse provided externally, the received data should be read from SBIDBR
before next serial clock is input. If the received data is not read, further data to be
received is canceled.
When the internal clock is used, the automatic wait function is executed until
received data is read from SBIDBR.
The maximum transfer speed when the external clock is used is determined by
the delay time between the time when an interrupt request is generated and the
time when received data is read.
Received data disappears if this data is not completely read before reception of
the next data terminates. In this case, the next data received is read.
Receiving data is ended by clearing the SIOS to “0” by the buffer full interrupt
service program or setting the SIOINH to “1”. When the SIOS is cleared, received
data is transferred to the SBIDBR in complete blocks. The received mode ends
when the transfer is complete. In order to confirm if data is surely received by the
program, set the SIOF (Bit3 in SBIDBR) to be sensed. The SIOF is cleared to “0”
when receiving is complete. After confirming that receiving has ended, the last
data is read. When the SIOINH is set, receiving data stops. The SIOF turns “0”
(the received data becomes invalid, therefore no need to read it).
Note: When the transfer mode is switched, the SBIDBR contents are lost. In case
that the mode needs to be switched, receiving data is concluded by clearing
the SIOS to “0”, read the last data, and then switch the mode.
88CS38B-106
2007-09-12
TMP88CS38B/CM38B/CP38B
Clear SIOS
SIOS
SIOF
SEF
SCK pin (Output)
SI pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
INTSBI interrupt
request
SBIDBR
a
Read received data
b
Read received data
Figure 2.9.26 Receive Mode (Example: Internal clock)
c.
8-bit transmit/receive mode
Set a control register to a transmit/receive mode and write data to the SBIDBR.
After the data is written, set the SIOS to “1” to start transmitting/receiving. When
transmitting, the data is output from the SO pin on the leading edges in
synchronous with the serial clock, starting from the least significant bit (LSB).
When receiving, the data is input to the SI pin on the trailing edges of the serial
clock. 8-bit data is transferred from the shift register to the SBIDBR, and the
INTSBI interrupt request occurs. The interrupt service program reads the
received data from the data buffer register and writes data to be transmitted. The
SBIDBR is used for both transmitting and receiving. Transmitted data should
always be written after received data is read.
When the internal clock is used, automatic-wait function is initiated until
received data is read and next data is written.
When the external clock is used, since the shift operation is synchronized with
the external clock, received data is read and transmitted data is written before
new shift operation is executed. The maximum transfer speed when the external
clock is used is determined by the delay time between the time when an interrupt
request is generated and the time when received data is read and transmitted
data is written.
When transmission starts, a value which is the same as the last bit of previously
transmitted data is output from the time SIOF is set to “1” until the falling edge of
SCK occurs.
Transmitting/receiving data is ended by cleaning the SIOS to “0” by the INTSBI
interrupt service program or setting the SIONH to “1”. When the SIOS is cleared,
received data is transferred to the SBIDBR in complete blocks. The
transmit/receive mode ends when the transfer is complete. In order to confirm if
data is surely transmitted/received by the program, set the SIOF (bit 3 in
SBISRB) to be sensed. The SIOF becomes “0” after transmitting/receiving is
complete. When the SIONH is set, transmitting/receiving data stops. The SIOF
turns “0”.
Note: When the transfer mode is switched, the SBIDBR contents are lost. In case
that the mode needs to be switched, conclude transmitting/receiving data by
clearing the SIOS to “0”, read the last data, and then switch the transfer mode.
88CS38B-107
2007-09-12
TMP88CS38B/CM38B/CP38B
Clear SIOS
SIOS
SIOF
SEF
SCK pin (Output)
SO pin
a0
a1
a2
a3
a4
a5
a6
a7
b0
b1
b2
b3
b4
b5
b6
b7
SI pin
c0
c1
c2
c3
c4
c5
c6
c7
d0
d1
d2
d3
d4
d5
d6
d7
INTSBI interrupt
request
SBIDBR
a
c
Write transmitted
data (a)
b
Read received Write transmitted
data (c)
data (b)
d
Read received
data (d)
Figure 2.9.27 Transmit/Receive Mode (Example: Internal clock)
SCK pin
SIOF
SO pin
Bit6
Bit7 in last transmitted word
tSODH = Min 4/fc [s] (In NORMAL mode, IDLE mode)
Figure 2.9.28 Transmitted Data Hold Time at End of Transmit/Receive
88CS38B-108
2007-09-12
TMP88CS38B/CM38B/CP38B
2.10 Remote Control Signal Preprocessor/External Interrupt 3 Input Pin
The remote control signal waveform can be determined by inputting the remote control signal
waveform from which the carrier wave was eliminated by the receive circuit to P30
(INT3/RXIN) pin. When the remote control signal preprocessor/external interrupt 3 pin is also
used as the P30 port, set the P30 port output latch to “1”. When it is not used as the remote
control signal preprocessor/external interrupt 3 input pin, it can be used for normal port.
2.10.1
Configuration
11
fc/2
10
fc/2
8
fc/2
7
fc/2
6
fc/2
5
fc/2
2
fc/2
Receive bit
counter
Receive bit counter value monitor (RBCTM)
Selector
RNC
INT3/RXIN
Polarity
select
Noise canceller to
RNCM
INT3
Interrupt
request
Interrupt
select
INT.
EINT
Measurement
width select
8-bit
up counter
Match detect
Selector
SRM
6
2 3
RPOLS
fc/2
8
fc/2
10
fc/2
12
fc/2
2
RCCK
Remote control receive
counter register (RXCTR)
2
RMM
4
RCS CREGA
RXCR1
RXCR2
Remote control receive
control register 1
Remote control receive
control register 2
Shift register
Remote control receive
data buffer register
(RXDBR)
Figure 2.10.1 Remote Control Signal Preprocessor
2.10.2
Remote Control Signal Preprocessor Control
When the remote control signal preprocessor is used, operating states are controlled and
monitored by the following registers. Interrupt requests also use the remote control signal
preprocessor/external interrupt 3 input pin.
•
Remote control receive control register 1 (RXCR1)
•
Remote control receive control register 2 (RXCR2)
•
Remote control receive counter register (RXCTR)
•
Remote control receive data buffer register (RXDBR)
•
Remote control receive status register (RXSR)
When this pin is used for the external interrupt 3 input, set EINT in RXCR1 to other
than “11”.
88CS38B-109
2007-09-12
TMP88CS38B/CM38B/CP38B
Remote Control Receive Control Register 1
RXCR1
7
(00FE8H)
6
RCCK
5
4
RPOLS
3
2
1
EINT
0
(Initial value: 0000 0000)
RNC
6
00: fc/2 (Hz)
8-bit up counter source clock
select
RCCK
Remote control signal polarity
select
RPOLS
01: fc/2
8
10: fc/2
10
11: fc/2
12
0:
Positive
1:
Negative
00: Rising edge
EINT
01: Falling edge (at RPOLS = 0)
Interrupt source select
10: Rising/falling edge
R/W
11: 8-bit receive end
001: 2 /fc × 7 − 1/fc (s)
2
010: 2 /fc × 7 − 1/fc
5
011: 2 /fc × 7 − 1/fc
6
100: 2 /fc × 7 − 1/fc
7
Noise canceler noise
eiminating time select
RNC
101: 2 /fc × 7 − 1/fc
8
110: 2 /fc × 7 − 1/fc
10
111: 2 /fc × 7 − 1/fc
12
000: Noise canceler disable
Note 1:
fc: High-frequency clock [Hz]
Note 2:
After reset, RPOLS do not change the set value in the receiving remote control signal. For setting interrupt
edge and measurement data, use EINT and RMM.
Remote Control Receive Control Register 2
RXCR2
7
6
(00FE9H)
5
4
CREGA
3
2
RCS
RMCEN
CREGA
Setting of detect time for
match with 8-bit up counter
upper 4 bits
RCS
8-bit up counter start control
RMCEN
Remote control signal
preprocesser enable/disable
1
0
RMM
(Initial value: 0000 0000)
Match detect time (Tth) = 16 × CREGA/RCCK [s]
CREGA = 0H to FH
CREGA = 2H, RCCK = fc/2 [Hz], at fc = 16 MHz,
DV1CK = 1
Tth = 128 [μs]
6
Example:
0:
Stop and counter clear
1:
Start
0:
Disable
1:
Enable
R/W
00:
RMM
Measurement mode select
(Invalid when EINT = “10”)
01:
Refer to Talbe 2.10.1
10:
11:
Note 1:
fc: High-frequency clock [Hz]
Note 2:
When an interrupt source is set for rising/falling edge, low and high widths are forcibly measured
separately.
Note 3:
Set CREGA (0H to FH) before EINT sets to 8-bit receive end.
Figure 2.10.2 Remote Control Receive Control Register 1, 2
88CS38B-110
2007-09-12
TMP88CS38B/CM38B/CP38B
Remote Control Receive Counter Register
RXCTR
7
6
5
4
3
2
1
0
Read only
(Initial value: 0000 0000)
4
3
2
1
0
Read only
(Initial value: 0000 0000)
4
3
2
1
0
OVFF
SRM
RNCM
Read only
(Initial value: 0000 *000)
(00FEAH)
Remote Control Receive Data Buffer Register
RXDBR
7
6
5
(00FEBH)
Remote Control Receive Status Register
RXSR
7
6
(00FECH)
5
RBCTM
RBCTM
Receive bit counter value
monitor
OVFF
8-bit up counter overflow flag
SRM
Data buffer register input
monitor
RNCM
0:
No overflow
1:
Overflow
0:
Upper 4 bits of 8 bit up counter < CREGA
1:
Upper 4 bits of 8 bit up counter ≥ CREGA
Read
only
Remote control signal monitor
after passing through noise
canceler
*: Don’t care
Figure 2.10.3 Remote Control Receive Counter Register, Data Buffer Register, Status Register
88CS38B-111
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.10.1 Combination of Interrupt Source and Measurement Mode
RPOLS
EINT
RMM
Interrupt Source
Measurement Mode
00
00
10
11
01
0
01
10
11
10
−
00
11
Receive end
10
00
00
10
11
01
1
01
10
11
10
−
00
11
Receive end
10
88CS38B-112
2007-09-12
TMP88CS38B/CM38B/CP38B
2.10.3
Noise Elimination Time Setting
The remote control receive circuit has a noise canceler. By setting RNC in RXCR1, input
signals shorter than the fixed time can be eliminated as noise.
Table 2.10.2 Noise Elimination Time Setting (fc = 16 MHz)
RNC
Minimum Signal Pulse Width
−
000
2.10.4
Maximum Noise Width to be Eliminated
−
001
(2 + 5)/fc
(2.31 μs)
(2 × 7 − 1)/fc
(1.69 μs)
010
(2 + 5)/fc
(16.31 μs)
(2 × 7 − 1)/fc
(13.88 μs)
011
(2 + 5)/fc
(32.31 μs)
(2 × 7 − 1)/fc
(27.88 μs)
100
(2 + 5)/fc
(64.31 μs)
(2 × 7 − 1)/fc
(55.88 μs)
101
(2 + 5)/fc
(128.3
μs)
(2 × 7 − 1)/fc
(111.9 μs)
110
(2 + 5)/fc
(512.3
μs)
(2 × 7 − 1)/fc
(447.9 μs)
111
(2 + 5)/fc
(1.024 ms)
(2 × 7 − 1)/fc
(895.9 μs)
5
8
9
10
11
13
14
2
5
6
7
8
10
11
Operation
(1) Interrupts at rising, falling, or rising/falling edge, and measurement modes
First set EINT and RMM. Next, set RCS to “1”; the 8-bit up counter is counted up by
the internal clock. After measurement, the 8-bit up counter value is saved in RXCTR.
Then, the 8-bit up counter is cleared, an INT3 request is generated, and the 8-bit up
counter resumes counting.
If the 8-bit up counter overflows (FFH) before measurement is completed, an INT3
request is generated and the overflow flag (OVFF) is set to “1”. Then, the 8-bit up
counter is cleared. An overflow can be detected by reading OVFF by the interrupt
processing. To restart the 8-bit up counter, set RCS to “1”.
Setting RCS to “1” zero clears OVFF.
88CS38B-113
2007-09-12
88CS38B-114
RXCTR
8-bit
up counter value
RXCTR
8-bit
up counter value
RXCTR
8-bit
up counter value
INT3
request
RCCK
RNCM
I−3 I−2 I−1
I−3 I−2 I−1
I−3 I−2 I−1
I
I
I
I
I
1
1
1
2
2
2
3
3
3
1
5
6
7
8
2
m
m
1
(c) High width measurement
m−2m−1
2
(b) Rising edge cycle measurement
4
m
(a) Low width measurement
m−2m−1
n−2 n−1
3
n−2 n−1
m−4m−3m−2m−1
3
n
m
n
m
n
1
1
1
2
2
2
3
3
3
TMP88CS38B/CM38B/CP38B
Figure 2.10.4 Rising Edge Interrupt Timing Chart (RPOLS = 0)
2007-09-12
88CS38B-115
RXCTR
8-bit
up counter value
RXCTR
8-bit
up counter value
RXCTR
8-bit
up counter value
INT3
request
RCCK
RNCM
I−3 I−2 I−1
I−3 I−2 I−1
I−3 I−2 I−1
I
I
I
I
I
1
1
1
2
2
2
3
3
3
1
5
6
7
8
2
m
m
1
(c) Low width measurement
m−2m−1
2
(b) Falling edge cycle measurement
4
m
(a) High width measurement
m−2m−1
n−2 n−1
3
n−2 n−1
m−4m−3m−2m−1
3
n
m
n
m
n
1
1
1
2
2
2
3
3
3
TMP88CS38B/CM38B/CP38B
Figure 2.10.5 Falling Edge Interrupt Timing Chart (RPOLS = 0)
2007-09-12
RXCTR
8-bit
up counter value
INT3
request
RCCK
RNCM
I−3 I−2 I−1
I
I
1
2
3
m
m
1
2
(a) High and low width measurement
m−2m−1
3
n−2 n−1
n
n
1
2
3
TMP88CS38B/CM38B/CP38B
Figure 2.10.6 Rising/Falling Edge Interrupt Timing Chart
88CS38B-116
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) 8-bit receive end interrupts and measurement modes
By determining one-cycle remote control signal as one-bit data set to “0” or one-pulse
width remote control signal as one-bit data set to “1”, an INT3 request is generated
after 8-bit data is received. When “0” is determined, this means the upper four bits in
the 8-bit up counter have not reached the CREGA value. When “1” is determined, this
means the upper four bits in the 8-bit up counter have reached or exceeded the CREGA
value. The 8-bit up counter value is saved in RXCTR after one bit is determined. The
determined data is saved, bit by bit, in RXDBR at the rising edge of the remote control
signal (when RPOLS = 1, falling edge). The number of bits saved in RXDBR is counted
by the receive bit counter and saved in RBCTM. RBCTM is set to “0001B” at the rising
edge of the input (when RPOLS = 1, falling edge) after the INT3 request is generated.
RNCM
RCCK
8-bit up
counter value
FE
FF
1
Set to “1” by command.
RCS
OVFF
Receive bit
counter value*
n−1
n
RBCTM*
n−1
n
INT3
request
*: Valid only when 8 bits are received.
Figure 2.10.7 Overflow Interrupt Timing Chart
88CS38B-117
2007-09-12
RXDBR
SRM
8-bit
up counter
value
CREGA
INT3
request
Receive bit
counter
value
RNCM
01
02
1
03
04
05
8-bit receive end interrupt setting
06
07
01
07
0
6
01
02
03
(a) Rising Edge cycle measurement
02
1
04
05
06
07
08
7
09
0A
0B
0C
0E
0F
10
11
80H
1
01
02
[Application] Low width measurement
0C
8
TMP88CS38B/CM38B/CP38B
Figure 2.10.8 8-Bit Receive End Interrupt Timing Chart (PROLS = 0)
88CS38B-118
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.10.3 Count Clock for Remote Control Preprocessor Circuit (at fc = 16 MHz)
Count Clock (RCCK)
Resolution [μs]
Maximum Setting Time [ms]
00
4
1.024
01
16
4.096
10
64
16.38
11
256
65.53
88CS38B-119
2007-09-12
TMP88CS38B/CM38B/CP38B
2.11 8-Bit AD Converter (ADC)
The TMP88CS38B/CM38B/CP38B has a 8-bit successive approximation type AD converter.
2.11.1
Configuration
Figure 2.11.1 shows the circuit configuration of the AD converter.
The AD converter includes control registers ADCCRA and ADCCRB, conversion result
registers ADCDR1 and ADCDR2, a DA converter, a sample hold circuit, a comparator, and
sequential transducer circuit.
To use P5 and P6 as analog inputs, clear the output latch for P5 and P6 to “0”. Also, clear
the input/output control registers (P5CR1 and P6CR) to “0”.
VDD
VSS
DA converter
A
B
AIN0
AIN1
Y
Reference
voltage
Sample hold
circuit
Analog input multiplexer
ADS
8
Analog
comparator
E
F
AIN4
AIN5
S
EN
SAIN
Successive approximate circuit
3
Shift clock
AINDS
INTADC
Control circuit
EN
6
3
2
8
EOCF ADBF
AD8TRG
external
trigger signal
ADRS
P5CR, P6CR
ADCCRA
P5, P6 port input/output control register
AMD
ACK
ADCCRB
AD converter control register
ADCDR1, ADCDR2
AD conversion result register
Figure 2.11.1 AD Converter (ADC)
2.11.2
Control Register
The following register are used for AD converter.
•
AD converter control register 1 (ADCCRA)
•
AD converter control register 2 (ADCCRB)
•
AD conversion result register (ADCDR1/ADCDR2)
(1) AD converter control register 1 (ADCCRA)
ADCCRA control AD conversion start, AD operation mode select, analog input
control and analog input channel select.
(2) AD converter control register 2 (ADCCRB)
ADCCRB control AD conversion time select.
(3) AD conversion result register (ADCDR1)
AD conversion result is stored after end of conversion.
(4) AD conversion result register (ADCDR2)
For monitoring status of conversion.
Figure 2.11.2 and Figure 2.11.3 show AD converter control register.
88CS38B-120
2007-09-12
TMP88CS38B/CM38B/CP38B
AD Converter Control Register 1
ADCCRA
7
(0000EH)
ADRS
6
5
AMD
4
3
AINDS
“0”
2
1
0
SAIN
(Initial value: 0001 0000)
The ADRS bit is automatically cleared after starting AD conversion.
ADRS
AD conversion start
AMD
AD operation mode select
AINDS
Analog input control
SAIN
Analog input channel
selection
Note 1:
During AD conversion, setting ADRS to “1” initializes the ADRS bit
and resets conversion.
0: −
1: AD conversion restart
00: STOP mode
01: Software start mode
00: Trigger start mode
11: Reserved
0: Analog input enable
1: Analog input disable
000: select AIN0
001: select AIN1
010: select AIN2
011: select AIN3
100: select AIN4
101: select AIN5
110: −
111: −
R/W
Select analog input when AD converter stops.
Note 2:
When the analog input is all use disabling, the AINDS should be set to “1”.
Note 3:
During conversion, do not perform output instruction to maintain a precision for all of the pins.
And port near to analog input, do not input intense signaling of change.
Note 4:
The ADRS is automatically cleared to “0” after starting conversion.
Note 5:
Always set bit3 in ADCCRA to “0”.
Note 6:
Do not set ADRS (Bit7 in ADCCRA) to “1” during AD conversion. Reset it after confirming with EOCF (Bit5
in ADCDR2) that the conversion is completed or after generation an interrupt signal (INTADC) (by the
interrupt processing routine or the like).
Note 7
In the trigger mode, the system does not accept the second and subsequent triggers after accepting the first
trigger for starting AD conversion. To restart AD conversion by a trigger, set AMD (Bits 6 and 5 in ADCCRA)
to “00” and then put the system in trigger start mode again (with AMD = “10”).
Note 8:
When the system enters STOP mode, AD converter control register 1 (ADCCRA) is initialized.
Reset this register after the system reenters NORMAL mode.
AD Converter Control Register 2
ADCCRB
7
(0000FH)
6
5
4
“0”
“1”
3
2
1
0
ACK
ACK
“0”
(Initial value: **0* 000*)
DV1CK = 0
DV1CK = 1
Conversion
time
fc = 16 MHz fc = 8 MHz fc = 16 MHz fc = 8 MHz
000
Reserved
001
010
ACK
AD conversion time select
011
156/fc [s]
−
19.5
−
39
100
312/fc [s]
19.5
39.0
39
78
101
624/fc [s]
39.0
78.0
78
156
110
1248/fc [s]
78.0
−
156
−
111
R/W
Reserved
Note 1:
Do not use setting except the above liset.
Note 2:
Set conversion time by analog reference voltage (VDD) as follows.
Note 3:
Always set bit0 and bit5 in ADCCRB to “0” and set bit4 in ADCCRB to “1”.
Note 4:
When a read instruction for ADCCRB, bit6 to 7 in ADCCRB read in as undefined data.
VDD = 4.5 to 5.5 V (15.6 μ or more)
Note 5:
fc: High-frequency clock [Hz]
Note 6:
When the system enters STOP mode, AD converter control register 2 (ADCCRA) is initialized.
Reset this register after the system reenters NORMAL mode.
Figure 2.11.2 AD Converter Control Register
88CS38B-121
2007-09-12
TMP88CS38B/CM38B/CP38B
AD Conversion Result Register
ADCDR1
7
6
(00031H)
AD07
ADCDR2
7
6
(00032H)
−
−
AD06
5
4
3
2
1
0
AD05
AD04
AD03
AD02
AD01
AD00
5
4
3
2
1
0
EOCF
ADBF
−
−
−
−
EOCF
AD conversion end flag
ADBF
AD conveersion busy flag
Note 1:
0:
1:
0:
1:
(Initial value: 0000 0000)
(Initial value: **00 ****)
Under conversion or before conversion
End of conversion
During stop of AD conversion
During AD conversion
Read
only
The EOCF is cleared to “0” when reading the ADCDR1.
Therefore, the AD conversion result should be read to ADCDR1 more first than ADCDR2.
Note 2:
ADBR is set to “1” by starting AD conversion and cleared to “0” by end of AD conversion. Additionally,
ADBF is cleared to “0” by setting AMD = “00” in ADCCR2 or entering to the STOP mode.
Figure 2.11.3 AD Converter Result Register
2.11.3
AD Converter Operation
The high side of an analog reference voltage is applied to VDD, and the low side is
applied to VSS pin. Dividing a reference voltage between VDD and VSS to the voltage
corresponding to a bit by a rudder resistance and comparing it with the analog input
voltage converts the AD.
Table 2.11.1 AD Converter Operation Mode
Mode
AD converter disable mode
Function
AD converter stop mode. This mode is always used to change modes.
Software start mode
Single AD conversion of 1 channel which specifies input.
Trigger start mode
Single AD conversion of 1 channel which specifies input (AD8TRG) from
Key-on wakeup circuit as a trigger.
.
2.11.4
Interrupt
Interrupt request signal occur at the timing when the EOCF bit is set to “1”.
88CS38B-122
2007-09-12
TMP88CS38B/CM38B/CP38B
2.11.5
AD Converter Operation Modes
When the MCU places in the STOP mode during the AD conversion, the conversion is
stopped and the ADCDR2 content becomes indefinite. After returning from the STOP mode,
the EOCF and INTADC does not occur. Therefore, the AD conversion must be restarted
after returning from the STOP mode.
ADS
ADCDR2
Invalid
Result
Invalid
Invalid
Result
EOCF
Processing
Read Start
Read Start
Start
Figure 2.11.4 AD Conversion Timing chart
(1) AD conversion in STOP mode
When the AD converter stop mode is specified during AD conversion, the AD
conversion is stopped immediately. The AD conversion is not implemented, so the
undefined value is not written to the AD conversion result register. The AD conversion
start commands which occur is the AD converter stop mode are ignored.
This mode is automatically selected by reset.
This mode is used to change the AD converter operation mode.
(2) Single mode
When the AMD (Bit6, 5 to in ADCCRA) set to “01”, the AD conversion signal mode
This mode does AD conversion of single channel, and conversion result is stored in
ADCDR1. The EOCF (Bit5 in ADCDR2) is set to “1” at end of one conversion, and an
intcrrupt request signal occurs. The EOCF is cleared to “0” by reading the AD
conversion registers.
But when the AD conversion is restarted before the ADCDR is read, the EOCF is
cleared to “0” and the last AD conversion result is maintained till next conversion end.
Do not set ADRS (Bit7 in ADCCRA) during AD conversion. Again set it after
confirming with EOCF (Bit5 in ADCDR2) that the conversion is completed or after
generating an interrupt signal (INTADC) (by the interrupt processing routine or the
like).
ADS
ADCDR2
Invalid
AD conversion result
EOCF
ADBF
Conversion time
(Reference to ADCCRB register)
Read
Start
Figure 2.11.5 Single Mode
88CS38B-123
2007-09-12
TMP88CS38B/CM38B/CP38B
Example:
The AD conversion starts after 19.5 μs (at fc = 16 MHz) and AIN4 pin are selected as the conversion time
and the analog input channel. Confirming the EOCF, the converted value is read out, and the 8 bits data
is stored to address 009EH in RAM. The operation mode is a signal mode.
;AIN SELECT
LD
(P5), 00000000B
LD
(P5CR1), 00000000B
LD
(P6), 00000000B
LD
(P6CR), 00000000B
LD
(ADCCRA), 00100100B
;
Selects AIN4, selects the software start mode
LD
(ADCCRB), 00011000B
;
Selects the conversion time and the operation mode
; AD CONVERT START
SLOOP:
SET
(ADCCRA). 7
;
ADRS = 1
TEST
(ADCCR2). 5
;
EOCF = 1 ?
JRS
T, SLOOP
; RESULT DATA READ
LD
(9EH), (ADCDR1)
(3) Trigger start mode
The AD conversion of a specified single channel is executed when input (AD8TRG)
from Key-on wakeup circuit is set as trigger, the conversion result is stored in the
ADCDR1.
The EOCF (Bit5 in ADCDR2) is set to “1” at end of one conversion, and an interrupt
request signal occurs.
It needs to be set the STOP mode by bit5 to 6 in ADCCRA before the AD conversion is
executed again.
2.11.6
Analog Input Voltage and AD Conversion Result
The analog input voltage is corresponded to the 8-bit digital value converted by the AD as
shown in Figure 2.11.6.
AD Conversion
result
FFH
FEH
FDH
03H
02H
01H
0
1
2
3
253
254
255
256
×
VDD − VSS
Analog input voltage
256
Figure 2.11.6 Analog Input Voltage and AD Conversion Result (typ.)
88CS38B-124
2007-09-12
TMP88CS38B/CM38B/CP38B
2.11.7
STOP Modes during AD Conversion
When standby mode (STOP mode) is entered forcibly during AD conversion, the AD
convert operation is suspended and the AD converter is initialized. (ADCCRA and
ADCCRB are initialized to initial value.) Also, the conversion result is indeterminate.
(Conversion results up to the previous operation are cleared, so be sure to read the
conversion results before entering standby mode.) When restored from standby mode, AD
conversion is not automatically restarted, so it is necessary to restart AD conversion after
setting ADCCRA and ADCCRB. Note that since the analog reference voltage is
automatically disconnected, there is no possibility of current flowing into the analog
reference voltage.
2.11.8
Notice of AD Converter
(1) Analog input voltage range
Voltage range of analog input (AIN0 to AIN5) must be forced from VSS to VDD. If
input voltage of which out of range is forced to analog input pin, AD conversion result
to unknown. Also, this cause other analog input pin unstable.
(2) I/O port with analog input
Analog input pins (AIN0 to AIN5) are also I/O port. During AD conversion using any
analog input pin, don’t operate other I/O port with analog input. Because, AD accuracy
would be worse. Also, other electrically swinging port without analog input may cause
noise to near analog input pin.
(3) Reduce to noise
Figure 2.11.7 is shown as internal equivalent circuit of analog input pin.
Increasing output impedance of analog input supply, cause noise or other non-good
condition.
Therefore, output impedance of analog input supply must be less than 5 kΩ.
And we recommend to connect capacitance to analog input pin.
AINx
Analog input
supply impedance
5 kΩ (max)
Internal resistance
R = 5 kΩ (typ.)
Analog converter
Internal capacitance
C = 22 pF (typ.)
DA converter
Figure 2.11.7 Analog Input Equivalent Circuit and Analog Input Pin
88CS38B-125
2007-09-12
TMP88CS38B/CM38B/CP38B
2.12 Key-on Wakeup
In this MCU the IDLE mode is also released by low active port inputs. The low input voltage
is regulated higher than the other normal ports. Therefore the ports can be enabled by analog
input level.
2.12.1
Configuration
Port P53
AIN0
AD converter
VIL ≤ VDD × 0.65
KWU0
AD8TRG
KWU1
Port P54
AIN1
KWU2
Port P55
AIN2
KWU3
Port P56
AIN3
KWU 4
Port P60
AIN4
KWU5
Port P61
AIN5
Noise
reject
circuit
INTKWU
INTAD
EN
*
IDLE5 IDLE4 IDLE3 IDLE2 IDLE1 IDLE0
IN
IN
IN
IN
IN
IN
IDLECR (00FD0H)
*
*
IDLE5 IDLE4 IDLE3 IDLE2 IDLE1 IDLE0
IN
IN
IN
IN
IN
IN
IDLEIN (00FD0H)
Figure 2.12.1 Key-on Wakeup Control Circuit
2.12.2
Control
P53 to P56 and P60, P61 ports can be controlled by IDLE control register (IDLECR).
It can be configured as enable/disable in one-bit unit. When those pins are used by IDLE
mode release, those pins must be set input mode (P5CR1, P5, P6CR, P6, ADCCRA).
IDLE mode is controlled by system control register 2 (SYSCR2) and maskable interrupts.
After the individual enable flag (EF5) is set to “1”, the IDLE mode must starts. When
enabled port input generates INTKWU interrupt, the IDLE mode is released. Low level
input voltage in those ports is regulated to less than VDD × 0.65 (V).
IDLE port monitorring register (IDLEIN) can be used to check state of ports.
INTADEN can enable to generate AD8TRG, which is used as trigger of AD converter
trigger start mode.
Noise reject circuit eliminate noise, which is less than 24 μs period.
88CS38B-126
2007-09-12
TMP88CS38B/CM38B/CP38B
IDLE Control Register
IDLECR
(00FD0H)
7
INTAD
EN
6
5
4
3
2
1
0
*
IDLE5
EN
IDLE4
EN
IDLE3
EN
IDLE2
EN
IDLE1
EN
IDLE0
EN
INTADEN
Generation of AD8TRG
IDLE5EN
Release IDLE mode by KWU5
IDLE4EN
Release IDLE mode by KWU4
IDLE3EN
Release IDLE mode by KWU3
IDLE2EN
Release IDLE mode by KWU2
IDLE1EN
Release IDLE mode by KWU1
IDLE0EN
Release IDLE mode by KWU0
0:
Disable
1:
Enable
0:
Disable
1:
Enable
0:
Disable
1:
Enable
0:
Disable
1:
Enable
0:
Disable
1:
Enable
0:
Disable
1:
Enable
0:
Disable
1:
Enable
(Initial value: 0*00 0000)
Write
only
*: Don’t care
IDLE Port Monitoring Register
IDLEIN
(00FD0H)
7
6
5
4
3
2
1
0
*
*
IDLE5
IN
IDLE4
IN
IDLE3
IN
IDLE2
IN
IDLE1
IN
IDLE0
IN
IDLE5IN
IDLE4IN
IDLE3IN
Input level of KWU5
Input level of KWU4
Input level of KWU3
IDLE2IN
Input level of KWU2
IDLE1IN
Input level of KWU1
IDLE0IN
Input level of KWU0
0:
“0” detect
1:
“1” detect
0:
“0” detect
1:
“1” detect
0:
“0” detect
1:
“1” detect
0:
“0” detect
1:
“1” detect
0:
“0” detect
1:
“1” detect
0:
“0” detect
1:
“1” detect
(Initial value: **00 0000)
Read
only
*: Don’t care
Figure 2.12.2 Key-on Wakeup Control Register
88CS38B-127
2007-09-12
TMP88CS38B/CM38B/CP38B
2.13 Pulse Width Modulation Circuit Output
The TMP88CS38B/CM38B/CP38B has four 12-bit resolution PWM output channels including
two 14-bit resolution selectable and six 7-bit resolution PWM output channels.
DA converter output can easily be obtained by connecting an external low-pass filter. PWM
outputs are multiplexed with general purpose I/O ports as; P40 ( PWM0 ) to P47 ( PWM7 ), P50
( PWM8 ), P51 ( PWM9 ). PWM output is negative logic. When these ports are used PWM outputs,
the corresponding bits of P4, P5 output latches and input/output control latches should be set to
“1”.
In STOP mode, PWM output pin keeps high-level. When operation mode is changed from
STOP mode to NORMAL mode, PWM control register (PWMCR1A, PWMCR2A, PWMCR1B,
PWMCR2B) are initialized.
88CS38B-128
2007-09-12
TMP88CS38B/CM38B/CP38B
2.13.1
Configuration
12-Bit Resolution PWM Output
Internal counter (2)
Internal counter (1)
14 13 12 11 10 9
8 7 6 5 4 3 2 1
Additional pulse generate
circuit
PWM0
Clock
2
(fc/2 or fc/2 )
8
7
PWM3
0
PWM data latch
5
PWM2
S
R
Compare circuit
All “0”
13
PWM1
PWM data latch
0
7
0
Transfer buffer (the upper)
Transfer buffer (the lower)
7
0
PWMDBR1
2
0
6
0
PWMCR1B
PWMCR1A
PWM control register 1B
PWM control register 1A
7-Bit Resolution PWM Output
Internal counter
Clock
7 6 5 4 3 2 1
2
PWM5
(fc/2 or fc/2 ) PWM 4
PWM7
PWM8
PWM9
S
R
Compare circuit
6
PWM6
0
PWM data latch
6
0
Transfer buffer
6
0
PWMDBR2
2
0
PWMCR2B
PWM control register 2B
6
0
PWMCR2A
PWM control register 2A
Figure 2.13.1 PWM Output Circuit
88CS38B-129
2007-09-12
TMP88CS38B/CM38B/CP38B
2.13.2
PWM Output Wave Form
(1) PWM0 to PWM1 Outputs
PWM0 and PWM1 output can be selected 12-bit or 14-bit resolution PWM outputs.
1.
12-bit resolution PWM output
When these are used as 12-bit PWM output, one period is TM = 213/fc [s] (When
DV1CK = 0) and TM = 214/fc [s] (When DV1CK = 1) and sub period is TS = TM/16.
The lower 8 bits of the PWM data latch controls the low level pulse width with a
cycle of TS. The lower 8 bits of the PWM data latch is n (n = 1 to 255), the low level
pulse width with a cycle becomes n × t0 [s] (t0 = 2/fc [s] when DV1CK = 0, t0 = 4/fc
[s] when DV1CK = 1).
The upper 4 bits of the PWM data latch controls a position to output the
additional pulses. When the upper 4 bits of the PWM data latch is m, the
additional pulses are generated in each of m periods out of 16 periods contained in
a TM period.
The relationship between the 4-bit data and the position of TS period where the
additional pulses are generated is shown in Table 2.13.1.
Table 2.13.1 The Addition Pulse (12-bit mode)
Bit Position of the Lower 4 Bits of PWMDRxH
Bit8
Relative position of TS in TM period where the additional
pulse is generated. (Number of TS (I) is listed)
Bit11
Bit10
Bit9
a)
0
0
0
0
No additional pulse
b)
0
0
0
1
8
c)
0
0
1
0
4, 12
d)
0
1
0
0
2, 6, 10, 14
e)
1
0
0
0
1, 3, 5, 7, 9, 11, 13, 15
Note 1:
The bit positions of a) to e) can be combined.
Note 2:
If the low order eight bits for the PWM data latch are set to “FFH”, be sure to set the high order four
bits for this latch to “00H”.
2.
14-bit resolution PWM output
When these are used as 14-bit PWM output, one period is TM = 215/fc [s] (When
DV1CK = 0) and TM = 216/fc [s] (When DV1CK = 1) and sub period is TS = TM/64.
The lower 8 bits of the PWM data latch controls the low level pulse width with a
cycle of TS. The lower 8 bits of the PWM data latch is n (n = 1 to 255), the low level
pulse width with a cycle becomes n × t0 [s] (t0 = 2/fc [s] when DV1CK = 0, t0 = 4/fc
[s] when DV1CK = 1).
The upper 6 bits of the PWM data latch controls a position to output the
additional pulses. When the upper 6 bits of the PWM data latch is m, the
additional pulses are generated in each of m periods out of 64 periods contained in
a TM period.
The relationship between the 6-bit data and the position of TS period where the
additional pulses are generated is shown in Table 2.13.2.
88CS38B-130
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.13.2 The Addition Pulse (14-bit mode)
Bit Position of the Lower 6 Bits of PWMDRxH
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
Relative position of TS in TM period where the additional
pulse is generated. (Number of TS (I) is listed)
a)
0
0
0
0
0
0
No additional pulse
b)
0
0
0
0
0
1
32
c)
0
0
0
0
1
0
16, 48
d)
0
0
0
1
0
0
8, 24, 40, 56
e)
0
0
1
0
0
0
4, 12, 20, 28, 36, 44, 52, 60
f)
0
1
0
0
0
0
2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 50, 54, 58, 62
g)
1
0
0
0
0
0
1, 3, 5, 7, 9, 11, 13, 15, 17, 19, 21, 23, 25, 27, 29, 31, 33,
35, 37, 39, 41, 43, 45, 47, 49, 51, 53, 55, 57, 59, 61, 63
Note 1:
The bit positions of a) to g) can be combined.
Note 2:
If the low order eight bits for the PWM data latch are set to “FFH”, be sure to set the high order 6 bits
for this latch to “00H”.
(2) PWM2 to PWM3 Outputs
PWM2 and PWM3 output are 12-bit resolution PWM outputs.
One period is TM = 213/fc [s] (When DV1CK = 0) and TM = 214/fc [s] (When DV1CK =
1) and sub period is TS = TM/16.
The lower 8 bits of the PWM data latch controls the low level pulse width with a cycle
of TS. The lower 8 bits of the PWM data latch is n (n = 1 to 255), the low level pulse
width with a cycle becomes n × t0 [s] (t0 = 2/fc [s] when DV1CK = 0, t0 = 4/fc [s] when
DV1CK = 1).
The upper 4 bits of the PWM data latch controls a position to output the additional
pulses. When the upper 4 bits of the PWM data latch is m, the additional pulses are
generated in each of m periods out of 16 periods contained in a TM period.
The relationship between the 4-bit data and the position of TS period where the
additional pulses are generated is shown in Table 2.13.1.
(3) PWM4 to PMW9 Outputs
These are 7-bit resolution PWM outputs.
One period is TN = 28/fc [s] (When DV1CK = 0) and TN = 29/fc [s] (When DV1CK = 1) .
The 7 bits of the PWM data latch controls the low level pulse width with a cycle of TN.
The lower 7 bits of the PWM data latch is k (k = 1 to 127), the low level pulse width
with a cycle becomes k × t0 [s] (t0 = 2/fc [s] when DV1CK = 0, t0 = 4/fc [s] when DV1CK
= 1).
88CS38B-131
2007-09-12
TMP88CS38B/CM38B/CP38B
14-bit resolution PWM mode: The additional pulse Ts (1) and Ts (63)
TM = 64 TS
TS (0)
TS (1)
TS (63)
t0
t0
n × t0
PWM0
to
PWM1
Pulse width = n × t0
Pulse width = (n + 1) t0
12-bit resolution PWM mode: The additional pulse Ts (1) and Ts (15)
TS (0)
TS (1)
TS (15)
t0
t0
n × t0
PWM2
to
PWM3
Pulse width = n × t0
Pulse width = (n + 1) t0
TN
PWM 4
to
PWM9
Pulse width = k × t0
Note 1:
Note 2:
If the pulse width is set to “00H”, PWM will note operate. Its output will remain high.
If the pulse width is set to “FFH”, settings for additional pulses cannot be made. Be sure to set the pulse
width to “00H”.
Figure 2.13.2 PWM Output Waveform
88CS38B-132
2007-09-12
TMP88CS38B/CM38B/CP38B
2.13.3
Control
PWM output is controlled by PWM control register (PWMCR1A, PWMCR1B, PWMCR2A,
PWMCR2B) and PWM data buffer register (PWMDBR1, PWMDBR2).
PWM Control Register 1A
7
PWMCR1A
(00028H)
6
−
5
4
3
2
ABORT1 START3 START2 START1 START0
ABORT1
Abort PWM operation of
channel 3 to 0
START3
Start channel 3
START2
Start channel 2
START1
Start channel 1
START0
Start channel 0
RESOLUTION1 Select channel 1 resolution
RESOLUTION2 Select channel 0 resolution
Note 1:
1
0
RESOLUTION
1
0
(Initial value: *000 0000)
0:
Operation
1:
PWM abort (PWM outputs are fixed to a high level.)
0:
Stop PWM3
1:
Start PWM3
0:
Stop PWM2
1:
Start PWM2
Write
only
0:
Stop PWM1
1:
Start PWM1
0:
Stop PWM0
1:
Start PWM0
0:
14-bit resolution
1:
12-bit resolution
0:
14-bit resolution
1:
12-bit resolution
*: Don’t care
Note 2
After set the ABORT1 to “1”, the ABORT1 is cleared to “0” automatically.
Note 3:
PWMCR1A is write-only register and cannot be used with any of the read-modify-write instructions such
as SET, CLR, etc.
PWM Control Register 1B
7
6
5
4
3
PWMCR1B
2
1
PWMCHS1
(00029H)
0
PWMHL
(Initial value: **** *000)
00: Channel 0
PWMCHS1
Select the PWM data latch of
12-bit PWM channel
01: Channel 1
10: Channel 2
Write
only
11: Channel 3
PWMHL
Note 1:
Note 2:
Select upper or lower data
transfer buffer (PWMDBR1)
0:
Lower 8 bits
1:
Upper 4 bits or 6 bits
*: Don’t care
PWMCR1B is write-only register and cannot be used with any of the read-modify-write instructions such
as SET, CLR, etc.
PWM Data Buffer Register 1
7
6
5
4
3
2
1
PWMDBR1
(0002AH)
Note 1:
0
Write only
(Initial value: 0000 0000)
PWMDBR1 is write-only register and cannot be used with any of the read-modify-write instructions such
as SET, CLR, etc.
Note 2:
When operation mode is changed from STOP mode to NORMAL mode, PWMCR1A, PWMCR1B are
initialized.
Figure 2.13.3 PWM Control Register 1A/1B and PWM Data Buffer Register 1
88CS38B-133
2007-09-12
TMP88CS38B/CM38B/CP38B
PWM Control Register 2A
7
PWMCR2A
(00FF5H)
−
6
5
4
3
1
0
ABORT2 START9 START8 START7 START6 START5 START4
ABORT2
Abort PWM operation of
channel 9 to 4
START9
Start channel 9
START8
Start channel 8
START7
Start channel 7
START6
Start channel 6
START5
Start channel 5
START4
Start channel 4
Note 1:
2
0:
Operation
1:
PWM abort
0:
Stop PWM9
1:
Start PWM9
0:
Stop PWM8
1:
Start PWM8
0:
Stop PWM7
1:
Start PWM7
0:
Stop PWM6
1:
Start PWM6
0:
Stop PWM5
1:
Start PWM5
0:
Stop PWM 4
1:
Start PWM 4
(Initial value: *000 0000)
Write
only
*: Don’t care
Note 2
After set the ABORT2 to “1”, the ABORT2 is cleared to “0” automatically.
Note 3:
PWMCR2A is write-only register and cannot be used with any of the read-modify-write instructions such
as SET, CLR, etc.
PWM Control Register 2B
7
6
5
4
3
2
PWMCR2B
1
PWMCHS2
0
(Initial value: **** *000)
(00FF6H)
PWMCHS2
Select the PWM data latch of
7-bit PWM channel
000:
Channel 4
001:
Channel 5
010:
Channel 6
011:
Channel 7
100:
Channel 8
101:
Channel 9
110:
Reserved
111:
Reserved
Write
only
Note 1:
*: Don’t care
Note 2:
PWMCR2B is write-only register and cannot be used with any of the read-modify-write instructions such as
SET, CLR, etc.
PWM Data Buffer Register 2
7
6
5
4
3
2
1
PWMDBR2
(00FF7H)
0
Write only
(Initial value: *000 0000)
Note 1:
*: Don’t care
Note 2:
PWMDBR2 is write-only register and cannot be used with any of the read-modify-write instructions such as
SET, CLR, etc.
Note 3:
When operation mode is changed from STOP mode to NORMAL mode, PWMCR2A, PWMCR2B are
initialized.
Figure 2.13.4 PWM Control Register 2A/2B and PWM Data Buffer Register 2
88CS38B-134
2007-09-12
TMP88CS38B/CM38B/CP38B
Binary Counter Control Register
CGCR
7
6
(00030H)
“0”
“0”
5
4
3
2
1
0
DV1CK
“0”
“0”
“0”
“0”
“0”
Select of input clock to
1st divider
DV1CK
0:
fc/4
1:
fc/8
Note 1:
*: Don’t care
Note 2:
The all bits except DV1CK are cleared to “0”.
(Initial value: 0000 0000)
R/W
Figure 2.13.5 DIVIDER Control Register
(1) Internal counter
The internal counter of PWM outputs is a free running counter. The all bits of
counter are set to “1” and are not counted up at one of the following conditions.
1.
During reset
2.
The operation mode is changed to STOP mode.
3.
Setting ABORTx (x: 1, 2) to “1”.
4.
The START3 to 0 are “0” in 12-bit PWM outputs. The START9 to 4 are “0” in 7-bit
PWM outputs.
5.
The lower 8-bit of PWM data latch in 12-bit PWM outputs is “00H”. The PWM
data latch in 7-bit PWM outputs is “00H”.
(2) Outputs control and programming of PWM data
The PWM outputs are fixed to a high-level immediately when the ABORTx (x: 1, 2) is
set to “1”. The PWM outputs starts the operation when the STARTx (x: 0 to 9) is set to
“1”.
The data from the transfer buffer to a PWM data latch is transferred when the all
bits of internal counter are set to “1”. Therefore, the data is transferred to a PWM data
latch immediately when the internal counter is initialized. And the data is transferred
to a PWM data latch at the beginning of the next cycle when all bits of the internal
counter are not set to “1”.
The sequence of writing the output data to PWM data latches is shown as follows;
1.
PWM0 to PWM1
a)
Write the channel number of PWM data latch to PWMCHS1 (Bit2 and 1 in
PWMCR1B) and clear PWMHL (Bit0 in PWMCR1B) to “0”.
b)
Write the lower 8-bit PWM output data to PWMDBR1.
c)
Write the channel number of PWM data latch to PWMCHS1 and set PWMHL
to “1”.
d)
Write the upper 4-bit or 6-bit PWM output data to PWMDBR1.
e)
Select the resolution of PWM output to RESOLUTIONx (x: 0, 1) (Bit0 and 1 in
PWMCR1A) and set STARTx (x: 0, 1) (Bit2 and 3 in PWMCR1B) to “1”.
Note: PWM output data must be write to PWMDBR1 in the order of the lower 8-bit
PWM output data, the upper 4-bit (or 6-bit) PWM output data. If the upper 4-bit
(or 6-bit) PWM output data is write to PWMDBR1, the lower 8-bit PWM output
data is not changed (except when lower 8-bit PWM output data is “00H”).
88CS38B-135
2007-09-12
TMP88CS38B/CM38B/CP38B
2.
PWM2 to PWM3
a)
Write the channel number of PWM data latch to PWMCHS1 and clear
PWMHL to “0”.
b)
Write the lower 8-bit PWM output data to PWMDBR1.
c)
Write the channel number of PWM data latch to PWMCHS1 and set PWMHL
to “1”.
d)
Write the upper 4-bit PWM output data to PWMDBR1.
e)
Set STARTx (x: 2, 3) to “1”.
1) Data transfer timing and STOP/ABORT timing (X: 0 to 3)
TM
TS
TM
TS
PWMx
m × t0
n × t0
Writing PWMDBR1
(Data m to n)
TS
PWMx
STARTx = 0
or
The lower 8-bit of PWM data latch = 00H
TS
PWMx
ABORT1 = 1
or
STOP mode
2) Restart timing when operating for 1ch or more
TM
TM
PWM0
PWM1
Restarting PWM1
Restarts after one cycle.
3) Restart timing after all channels stop
TM
TM
Start command
Figure 2.13.6 Waveform of PWM0 to PWM3
Note: PWM output data must be write to PWMDBR1 in the order of the lower 8-bit PWM output data, the
upper 4-bit (or 6-bit) PWM output data. If the upper 4-bit (or 6-bit) PWM output data is write to
PWMDBR1, the lower 8-bit PWM output data is not changed (except when lower 8-bit PWM output
data is “00H”).
88CS38B-136
2007-09-12
TMP88CS38B/CM38B/CP38B
3.
PWM4 to PWM9
a)
Write the channel number of PWM data latch to PWMCHS2.
b)
Write the lower 7-bit PWM output data to PWMDBR2.
c)
Set STARTx (x: 4 to 9) to “1”.
1) Data transfer timing and STOP/ABORT timing (X: 4 to 9)
TN
TN
PWMx
m × t0
n × t0
Writing PWMDBR2
(Data m to n)
PWMx
STARTx (x: 4 to 9) = 0
or
The lower 8-bit of PWM data latch = 00H
PWMx
ABORT2 = 1
or
STOP mode
2) Restart timing when operating for 1ch or more
TN
TN
PWM 4
PWM5
Restarting PWM5
Restarts after one cycle.
3) Restart timing after all channels stop
TN
TN
Start command
Figure 2.13.7 Waveform of PWM4 to PWM9
88CS38B-137
2007-09-12
TMP88CS38B/CM38B/CP38B
Example: at fc = 16 MHz, DV1CK = 0
PWM0 pin outputs a 14-bit resolution PWM wave form with a low level of 32 μs width and no additional pulse.
PWM1 pin outputs a 12-bit resolution PWM wave form with a low level of 16 μs width and no additional pulse.
PWM4 pin outputs a PWM wave form with a low level of 8 μs width.
LD
(CGCR), 00H
;
DV1CK = 0
LD
(PWMCR1B), 00H
;
Select the lower 8 bits of PWM0 output data latch
LD
(PWMDBR1), 80H
;
32 μs ÷ 4/fc = 80H
Select the upper 6 bits of PWM0 output data latch
LD
(PWMCR1B), 01H
;
LD
(PWMDBR1), 00H
;
No additional pulse = 00H
LD
(PWMCR1B), 02H
;
Select the lower 8 bits of PWM0 output data latch
LD
(PWMDBR1), 40H
;
16 μs ÷ 4/fc = 40H
LD
(PWMCR1B), 03H
;
Select the upper 4 bits of PWM0 output data latch
LD
(PWMDBR1), 01H
;
Additional pulse (Ts (8)) = 01H
LD
(PWMCR1A), 0DH
;
Start PWM0 and PWM1 ,
PWM0 : 14-bit resolution, PWM1 : 12-bit resolution
LD
(PWMCR2B), 00H
;
Select PWM4 output data latch
LD
(PWMDBR2), 20H
;
8 μs ÷ 2/fc = 20H
LD
(PWMCR2A), 01H
;
Start PWM4
88CS38B-138
2007-09-12
TMP88CS38B/CM38B/CP38B
2.14 Test Video Signal Output for Adjusting TV Screen
The TMP88CS38B/CM38B/CP38B has a built-in video signal output circuit to output
necessary signal for TV screen adjustment.
2.14.1
Picture pattern
:
Total eight types, monochromatic inversion possible
Output format
:
Three states (H, L, High-Z) output
Comp.sync duration time
L output
Black level/pedestal duration time
High-Z output
White level duration time
H output
Configuration
Horizontal pattern
generation circuit
Pattern mixed circuit
Vertical pattern
generation circuit
P62 (CSOUT)
Display pattern
generation circuit
3
SGIV
SGPAT2 to 0
SGVBLK
SGPAL
TVSCR
Test video signal output control register
Figure 2.14.1 Test Video Signal Output Circuit
88CS38B-139
2007-09-12
TMP88CS38B/CM38B/CP38B
2.14.2
Control
The test video signal output circuit can be controlled with the test video signal control
register.
TVSCR
(00FE6H)
7
6
5
SGEN SGVBLK SGPAL
SGEN
SGVBLK
SGPAL
4
3
2
1
0
SGIV
SGCHS
“0”
SGPAT
“0”
SG function selection
0:
Disable
1:
Enable
Picuture signal for VBLK duration
time
0:
Output
1:
No output
PAL/NTSC selection
0:
NTSC
1:
PAL
No inversion
SGIV
Pattern monochromatic inversion
0:
1:
Inversion
SGCHS
OSD synchronous signal selection
0:
Port
1:
Pseudo signal circuit
SGPAT
Display pattern
(Initial value: 0000 0000)
Write
only
000: Black on the whole screen
001: White on the whole screen
010:Cross hatch
011: Cross dot pattern
100: Cross bar
101: White on the upper side/black on the lower side
110:H signal pattern
111: H resolution pattern
Note 1:
Test video signal output function does work correctly when fc is not 16 MHz.
Note 2:
Clear the bit2 and bit0 of TVSCR to “0”.
Figure 2.14.2 Test Video Signal Control Register
88CS38B-140
2007-09-12
TMP88CS38B/CM38B/CP38B
2.14.3
Functions
Video signal output is to generate monochromatic picture signal output to take easily the
necessary tests such as TV screen white adjustment and screen distortion amplitude
adjustment implemented on the final manufacturing process of a TV receiver set.
Table 2.14.1 Display Pattern and TV Screen
Display Pattern
TV Screen
000
(Black on the whole surface)
001
(White on the whole surface)
010
(Cross hatch)
011
(Cross dot)
100
(Cross bar)
101
(White on the upper side/
black on the lower side)
110
(H signal pattern)
111
(H resolution pattern)
88CS38B-141
2007-09-12
TMP88CS38B/CM38B/CP38B
There are three states of the output to generate picture signal with the external circuit of
the resistance divided voltage.
Example of picture output generation)
5V
TMP88CS38B/
CM38B/CP38B
P62 (CSOUT)
to video input
GND
Three state of
the output
Picture signal output
(1 Vp-p)
(5 Vp-p)
88CS38B-142
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15 On-screen Display (OSD) Circuit
The TMP88CS38B/CM38B/CP38B features a built-in on-screen display circuit used to
display characters and symbols on the TV screen. There are 384 characters and any characters
can be displayed in an area of 32 columns × 12 lines (Include 2 columns for solid space). With an
OSD interrupt, additional lines can be displayed. The functions of the OSD circuit meet the
requirements of on-screen display functions of closed caption decoders based on FCC standards.
OSD circuit functions are as follows:
(1) Number of character fonts:
384
(2) Number of display characters: 384 (32 columns × 12 lines)
(3) Composition of character:
Horizontal 16 × vertical 18 dots
(4) Character sizes:
3 kinds for large, middle and small characters
(Selectable line by line)
(5) Character ornamentation function
Fringing function
Smoothing function
Slant function (Italics)
Blinking function
Underline
(6) Solid space
(7) Area plane function: 2 planes
(8) Full-raster blanking function
(9) Display colors
Character colors: 8 or 15 colors (Selectable character by character)
Fringe color:
8 or 15 colors (Selectable page by page)
Background color: 8 or 15 colors (Selectable page by page)
Area plane color: 8 or 15 colors (Selectable each of 2 planes)
Raster color:
8 or 15 colors (Selectable page by page)
(10) Display position: 256 horizontal steps and 512 vertical steps for code plane
: 512 horizontal steps and 512 vertical steps for area plane
(11) Window function: 512 vertical steps
(12) Half transparency output function
The TMP88CS38B/CM38B/CP38B outputs OSD through 3 planes; code, area, and raster. 3
planes function independently. In addition, they are displayed simultaneously. There is the
priority among these 3 planes, so they are displayed on a screen according to the priority.
These 3 planes have the priority such as
Code > Area > Raster.
88CS38B-143
2007-09-12
TMP88CS38B/CM38B/CP38B
1.
Code plane
OSD character is displayed on the code plane.
The code plane consists of 32 characters × 1 row and a total of 12 planes. The 12
planes have the priority such as code 1 > code 2 > ... > code 11 > code 12.
On the code plane, characters of 16 × 18 dots is displayed. These fonts are called
characters, and read from character ROM and display memory through the character
code on the display memory.
2.
Area plane
The area on a screen is displayed on the area plane.
The area plane can display 2 square areas of any size by specifying coordinates. The
2 planes have the priority such as area plane 1 > area plane 2.
2.15.1
Configuration
OSC1
Oscillation
circuit for
OSD display
OSC2
Horizontal position
counter
OSD
interrupt
OSD control
Horizontal position
decoder
Display memory
32 × 12 × 16 bits
Character
code
Vertical position counter
Character ROM
P71 ( VD )
384 × 16 × 18 bits
Vertical position decoder
P60 (Y/BLIN)
P61 (BIN)
P62 (GIN)
P63 (RIN)
Character
data
I
Y/BL
B
G
R
P57 (I)
Output signal selector
Jitter
elimination
circuit
Display output control
P70 ( HD )
P67 (Y/BL)
P66 (B)
P65 (G)
P64 (R)
Figure 2.15.1 OSD Circuit
88CS38B-144
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.2
Character ROM and Display Memory
(1) Character ROM
The character ROM contains 384 character fonts. The user can set fonts as desired.
The character ROM consists of 384 characters in 16 × 18 dots (Character codes 000H to
17FH). Each dot corresponds to one bit in the character ROM. When a bit in the
character ROM is set to “1”, the corresponding dot is displayed; if set to “0”, the dot is
not displayed. The start address in the character ROM corresponding to a character
code is determined by the following expression:
Start address in character ROM = CRA × 40H + 20000H
Since character code 000H is used as blank character, the character font for this
character code cannot be changed. Write “0” in the data of character code 000H.
Write the data “FFH” to all unused address (5th bit of an address is “1” and also the
lower 4 bits of an address are 2H to FH) in character ROM.
Figure 2.15.2 (a) shows an example of the character font configuration for the
character code 000H and 001H, together with the ROM addresses and data.
Figure 2.15.2 (b) shows the character ROM dump list for these 2 character fonts.
Note 1: CRA: Character code (000H to 17FH).
Note 2: A data can not be read from character ROM by software.
Note 3: When ordering a mask, load the data to character ROM at addresses 20000H to
25FFFH.
And the data in unused are of character ROM are must be specified to FFH.
Address Data
(Hex) (Hex)
20000
00
20001
00
20002
00
20003
00
20004
00
20005
00
20006
00
20007
00
20008
00
20009
00
2000A
00
2000B
00
2000C
00
2000D
00
2000E
00
2000F
00
20010
00
20011
00
Bit
Bit
7 6 5 4 3 2 1 07 6 5 4 3 2 1 0
Address Data
(Hex) (Hex)
20020
00
20021
00
20022
00
20023
00
20024
00
20025
00
20026
00
20027
00
20028
00
20029
00
2002A
00
2002B
00
2002C
00
2002D
00
2002E
00
2002F
00
20030
00
20031
00
Address Data
(Hex) (Hex)
20040
3F
20041
7F
20042
E0
20043
C0
20044
00
20045
00
20046
00
20047
01
20048
03
20049
07
2004A
0E
2004B
1C
2004C
38
2004D
70
2004E
FF
2004F
FF
20050
00
20051
00
Bit
Bit
7 6 5 4 3 2 1 07 6 5 4 3 2 1 0
(Character code 000H)
Address Data
(Hex) (Hex)
20060
C0
20061
E0
20062
70
20063
30
20064
30
20065
70
20066
E0
20067
C0
20068
80
20069
00
2006A
00
2006B
00
2006C
00
2006D
00
2006E
F0
2006F
F0
20070
00
20071
00
(Character code 001H)
(a) Character font configuration
20000/
20010/
20020/
20030/
20040/
20050/
20060/
20070/
00
00
00
00
3F
00
C0
00
00
00
00
00
7F
00
E0
00
00
FF
00
FF
E0
FF
70
FF
00
FF
00
FF
C0
FF
30
FF
00
FF
00
FF
00
FF
30
FF
00
FF
00
FF
00
FF
70
FF
00
FF
00
FF
00
FF
E0
FF
00
FF
00
FF
01
FF
C0
FF
00
FF
00
FF
03
FF
80
FF
00
FF
00
FF
07
FF
00
FF
00
FF
00
FF
0E
FF
00
FF
00
FF
00
FF
1C
FF
00
FF
00
FF
00
FF
38
FF
00
FF
00
FF
00
FF
70
FF
00
FF
00
FF
00
FF
FF
FF
F0
FF
00
FF
00
FF
FF
FF
F0
FF
(b) ROM dump list
Note:
Shared portions indicate unused data.
Figure 2.15.2 Character Font Configuration and ROM Dump List
88CS38B-145
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Display memory
Each character of the 384 characters displayed in 32 columns × 12 lines consists of 16
bits in the display memory. Five data items are written to the display memory:
Character code, color data, blinking specification, underline enable, and slant enable.
There are two modes for writing display data to the display memory. One mode is
used for writing all display data (Character code, color data, blinking specification,
underline enable, and slant enable) simultaneously. The other mode is used for
changing either character codes or the remaining data items (Color data, blinking
specification, underline enable, and slant enable). How to write display data to the
display memory is described in section 2.15.5.7 (1).
Note:
The display memory is in an unknown state at reset.
Display memory configuration
SLNT
EUL
•
Character code specification register (9 bits).... CRA8 to CRA0
•
Color data specification register (4 bits) ........... IDT/RDT/GDT/BDT
•
Blinking specification register (1 bit) ................ BLF
•
Underline enable register (1 bit)........................ EUL
•
Slant enable register (1 bit) ............................... SLNT
BLF
IDT
RDT
GDT
BDT
CRA8
CRA7
CRA6
Character color specification register
CRA5
CRA4
CRA3
CRA2
CRA1
CRA0
28
30
Character code specification register
Blinking specification register
Underline enable register
Slant enable register
Figure 2.15.3 Display Memory Bit Configuration
Column
1
Line
1
2
3
4
5
6
7
8
9
10
11
12
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
29
31
32
000 001 002 003 004 005 006 007 008 009 00A 00B 00C 00D 00E 00F 010 011 012 013 014 015 016 017 018 019 01A 01B 01C 01D 01E 01F
020 021 022 023 024 025 026 027 028 029 02A 02B 02C 02D 02E 02F 030 031 032 033 034 035 036 037 038 039 03A 03B 03C 03D 03E 03F
040
060
080
0A0
0C0
0E0
100
120
140
160
17F
Note:
Numerals in the table indicate (hexadecimal) addresses in the display memory.
Figure 2.15.4 Display Memory Address Configuration
88CS38B-146
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.3
OSD Circuit Control
The OSD circuit performs control functions using the OSD control registers which reside
in addresses 0001DH to 0001FH and 00024H to 00025H in the special function registers
(SFR), and in addresses 0F80H to 0FBFH in the data buffer register (DBR). Section
2.15.5.9 shows the OSD control registers. The OSD control registers are used to set display
start position, display character designs (that is, fringing, smoothing, color data, character
size, and etc.), display memory addresses, and character codes.
Setting the display on-off control bit, DON, (Bit0 in ORDON) to “1” enables display
(Starts display). Setting DON to “0” disables display (Halts display).
Note: The contents of OSD control registers except PIDS, P67S to P64S are initialized in
STOP mode.
2.15.4
OSD Control Register Write
There are lists of the OSD control registers on Table 2.15.5.10 and Table 2.15.5.11.
When data is written into a shaded register, the data is transferred to the OSD circuit,
and then the data becomes valid. After data is written into an unshaded register, the data
is transferred to the OSD circuit, and then the data becomes valid.
To transfer the contents of a control register to the OSD circuit, use data transfer request
register RGWR (Bit2 in ORDON).
Setting “1” in the RGWR register outputs the transfer request signal to the OSD circuit.
Three instruction cycles later, transfer of the written data to the OSD circuit starts. While
the data is being transferred, data transfer status monitoring flag RGWR (Bit2 in ORDON)
is “1”. When this transfer is completed, the flag is cleared to “0”.
Written data transfer register (1 bit) ....RGWR (Bit2 in ORDON)
“0”
....... Initialized state
Transfers written data to OSD circuit.
“1”
.......
(After transfer, RGWR is reset to 0.)
Note: Don’t write “0” to RGWR.
88CS38B-147
2007-09-12
TMP88CS38B/CM38B/CP38B
(1) RGWR system
OSD circuit
Q
D
Transfer pulse by RGWR = 1
LE
Register specified by RGWR
Figure 2.15.5 RGWR System
(2) Transfer timing
1.
No display area
When having set RGWR to “1” during no display area, the timing OSD register
can be transferred is at the falling edge of HD signal.
HD
RGWR register
Set RGWR register to “1”
Clear RGWR
Data transfer pulse
Transfer the contents of OSD registers
into OSD circuit
Figure 2.15.6 Data Transfer Timing in No Display Area
2.
Display area (including any lines specified as display off by character size)
When having set RGWR to “1” during display area, the timing OSD register can
be transferred is at the falling edge of HD signal when the display line has been
finished.
HD
Display line
RGWR register
Set RGWR register to “1”
Clear RGWR
Data transfer pulse
Transfer the contents of OSD registers
into OSD circuit
Figure 2.15.7 Data Transfer Timing in Display Area
88CS38B-148
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5
OSD Function
2.15.5.1 Signal Control (Port I/O)
(1) P6 port output select function
This function is used to select whether the contents of port P57, P67 to P64 will
be output or I, R, G, B, Y/BL signals of the OSD circuit will be output on pins P57,
P67 to P64.
P57 port output select registers (1 bit): PIDS (Bit3 in ORP6S)
PIDS = 0
PIDS = 1
I
Port
P57
P67 to P64 port output select registers (4 bits): P67S, P66S, P65S, P64S, (Bit7 to
4 in ORP6S)
P6nS = 0
P64
R
P65
G
P66
B
P67
Y/BL
P6nS = 1
Port
(2) OSD pin output polarity control function
This function is used to select the polarity of the OSD outputs for RGB, I and
Y/BL.
Output polarity control register (4 bits) ...... BLIV, YIV, RGBIV, IIV (Bit3 to 0 in
ORIV)
“0”
...... Active high
“1”
...... Active low
(3) OSD pin input polarity control
Input polarity control
Input polarity control register of RIN/GIN/BIN/Y/BLIN (2 bits)
For Y/BLIN .......................... YBLII (Bit5 in ORIV)
For RIN, GIN, and BIN ...... RGBII (Bit4 in ORIV)
Input polarity control
YBLII,
RGBII
“0”
“1”
......
......
Active high
Active low
Input polarity control register of HD / VD (2 bits)
For VD ..............VDPOL (Bit7 in ORIV)
For HD .............HDPOL (Bit6 in ORIV)
Input polarity control
VDPOL, HDPOL
“0”
....... Not invert input signal
“1”
....... Invert input signal
88CS38B-149
2007-09-12
TMP88CS38B/CM38B/CP38B
Register setting for the
following waveform
Input waveform to P70, P71
P71 ( VD )
VDPOL = 0
P70 ( HD )
HDPOL = 0
P71 ( VD )
VDPOL = 1
P70 ( HD )
HDPOL = 0
P71 ( VD )
VDPOL = 0
P70 ( HD )
HDPOL = 1
P71 ( VD )
VDPOL = 1
P70 ( HD )
HDPOL = 1
Figure 2.15.8 VD / HD input and VDPOL/HDPOL
(4) Y/BL signal select function
This function is used to select either Y or BL signal output from the Y/BL pin.
Y/BL signal select register (1 bit) .........YBLCS (Bit7 in ORP6S)
“0”
....... Y signal output
“1”
....... BL signal output
Y signal.............. Output in all OSD areas (Logical OR for R, G, B data
as character data, fringing data, area data, etc.)
BL signal ........... When EXBL is “0”:
Output in all display character areas
(except for character code 000H: Blank character)
When EXBL is “1”:
Output in the whole page
(5) I signal function select
When PISEL (Bit6 in ORETC) is set to “1” and PIDS (Bit3 in ORP6S) is set to “0”,
Port 57 (I pin) can be used as half transparency/half tone through an extra circuit.
At half transparency/half tone function, contents of IDT (Bit3 in ORDSN) is
make no sense. Therefore character color are limited to 8 colors.
Similarly background color, fringing color, raster plane color and area plane
color are limited to 8 colors.
When PISEL (Bit6 in ORETC) sets to “0” and, PIDS (Bit3 in ORP6S) set to “0”,
15 colors to be selectable.
88CS38B-150
2007-09-12
TMP88CS38B/CM38B/CP38B
(6) R, G, B, Y/BL Internal/external signal select.
Selects either R, G, B, and Y/BL signals from the internal OSD circuit, or RIN,
GIN, BIN, and Y/BLIN signals from external input.
R, G, B, Y/BL signal select registers (2 bits)........ MPXS1/MPXS0
(Bits 1 and 0 in ORP6S)
....... Simultaneous output (Signal from the OSD circuit
“00”
has higher priority.)
“01”
....... Output of signal from internal OSD circuit
“10”
....... Output of signal from external input
....... Simultaneous output (External input signal has
“11”
higher priority.)
88CS38B-151
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5.2 OSD Data Output Format Control
(1) Scan mode
The double scan mode is used to handle non-interlaced scanning TV. When
double scan mode is enabled, the vertical display counter increases every 2 scan
lines and a vertical size of a dot is double. This function is enabled by setting
VDSMD (Bit7 in ORETC) in the OSD control register to “1”.
Scan mode select register (1 bit)....... VDSMD (Bit7 in ORETC)
“0”
“1”
....... Normal mode
....... Double scan mode
Note 1: The data written to those control register is transferred to the OSD circuit and
become valid when the data is written.
Note 2: When OSD circuit is used on an interlace scanning TV, a jitter elimination
circuit must be enabled and set AFLD to “1” in JECR.
Table 2.15.5.1 The Difference of 2 Types of Scan Mode
Normal Mode
Double Scan Mode
Specification unit of vertical display
start position
One scanning line
Two scanning lines
1 dot height
−
Normal mode height × 2
Normal mode
Double scan mode
Normal mode
Interlace scanning
Double scan mode
Non-interlace scanning
Figure 2.15.9 Scan Mode
88CS38B-152
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5.3 Display Position Control
(1) Code display position setting
1.
Horizontal display start position
The horizontal display start position can be set in 256 steps by writing to OSD
control registers HS17 to HS10 (Bit7 to 0 in ORHS1). The value is in common with
all lines.
Specification unit: 2 TOSC
Specification steps: 256
Specification horizontal display start position: Line 1 to 12: HS17 to HS10
(ORHS1)
HS1 = (HS17 to HS10) H × 2TOSC + 20TOSC (Line1 to 12)
Note 1: TOSC: One cycle of OSD oscillation.
Note 2: The data written to these control registers is transmitted to OSD circuit by
setting RGWR (Bit2 in ORDON) to “1”.
2.
Vertical display start position
The vertical display start position can be specified for each display line using
512 steps by writing to VSn8 to VSn0 (in ORVSn (n: 1 to 12)).
Specification unit: 1 scan line
Specification steps: 512
Specification vertical display start position:
Line1: VS18 to VS10 (ORVS 1)
Line2: VS28 to VS20 (ORVS 2)
..
.
Line12: VS128 to VS120 (ORVS 12)
Line n: VSn = (VSn8 to VSn0) H × 1THD (n: 1 to 12)
Note 1: THD: One cycle of HD signal.
Note 2: The data written to these control registers is transmitted to OSD circuit by
setting RGWR (Bit2 in ORDON) to “1”.
Note 3: If display lines are overlapped each other, previous display line is enabled and
next line is disabled. If vertical display start positions of two or more lines are
set on same value, high priority line is enabled. Lines of OSD (VS1 to VS12)
are fixed priority levels as follows:
VS1 > VS2 > VS3 > ...... > VS12
Set the vertical display start position not to overlap display lines.
VS5 (Display on, small character)
VS2 (Display canceled, middle character)
VS3 (Display on, small character)
Occasion of overlapping
88CS38B-153
2007-09-12
TMP88CS38B/CM38B/CP38B
Note 4: The line which is displayed off is managed as a small size character line.
Note 5: Transfer the contents of vertical display start position registers into OSD circuit
before the position of the scanning line coincides with their own vertical
display start position.
(2) Area display position setting
The planes have the priority such as Code plane > Area plane 1 > Area plane 2 >
Raster plane.
1.
Horizontal display start and end position
The horizontal display start position can be set in 512 steps by writing to OSD
control registers AHSn8 to AHSn0 (Bit8 to 0 in ORAHSn). And also display stop
position is correspond to AHEn8 to AHEn0 (Bit8 to 0 in ORAHEn). (n: 1 to 2)
Horizontal display start position
AHSn = (AHSn8 to AHSn0)H × 2TOSC
Horizontal display end position
AHEn = (AHEn8 to AHEn0)H × 2TOSC
Note 1: TOSC: One cycle of OSD oscillation.
Note 2: If the horizontal display start position for characters is the same as that for
areas, the two positions are not displayed at the same time. The horizontal
display start position for characters is displayed 16 TOSC (Corresponding to a
register value of 8) later than that for areas.
88CS38B-154
2007-09-12
TMP88CS38B/CM38B/CP38B
2.
Vertical display start and end position
The vertical display start position can be set in 512 steps by writing to OSD
control registers AVSn8to AVSn0 (Bit8 to 0 ORAVSn). And also display stop
position is correspond to AVEn8 to AVEn0 (Bit8 to 0 in ORAVEn). (n: 1 to 2)
Vertical display start position
AVSn = (AVSn8 to AVSn0) H × THD
Vertical display end position
AVEn = (AVEn8 to AVEn0) H × THD
Note:
THD: One cycle of HD signal.
HD
VS1 VS2
AVS2 AVE2
AVS1 AVE1
HS1
1 2
34 5 6 7 8
910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Code plane 1
1 2 3 4 5 6 7 8
910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Code plane 2
AHS1
VD
Area plane 1
AHE1
Area plane 2
HS1
AHS2
AHE2
SS 1 2 3 4 5 6 7 8
910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS Code plane 9
SS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS Code plane 10
SS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS Code plane 11
SS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS Code plane 12
Figure 2.15.10 TV Scan Image
88CS38B-155
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5.4 Character Ornamentation Control
(1) Character sizes
Character size can be selected line by line from 3 sizes. And display on/off also
can be set line by line. Small, middle and large character size and display on/off
can be set with OSD control registers CSn (n: 1 to 12, ORCS4, ORCS8, ORCS12)
in the OSD control registers.
Character sizes: 3 sizes (Small, middle and large)
Character size and display on/off specification unit: Line
Character size select/display on/off register (2 bits × 12)
Line 1: CS1
Line 2: CS2
:
:
Line 12: CS12
Table 2.15.5.2 Character Size and Display On/Off Specifications (n: 1 to 12)
CSn (Upper bit)
CSn (Lower bit)
Character Size
Display On/Off
1
1
Small
On
1
0
Middle
On
0
1
Large
On
0
0
−
Off
Note 1: The display off line operates like the width of small character size line thought
the character is not displayed.
Note 2: The data written to these control registers is transmitted to OSD circuit by
setting RGWR (Bit2 in ORDON) to “1”.
Note 3: When OSD circuit is used on an interlace scanning TV, a jitter elimination
circuit must be enabled and set AFLD to “1” in JECR.
Note 4: When VDSMD and AFLD are “0”, only character of even display dot is
displayed. (Refer to 2.16 a jitter elimination circuit.)
Table 2.15.5.3 Dot and Character Sizes
VDSMD = 0 (Normal mode)
Dot Size
EULAn = 0
(Underline
off)
EULAn = 1
(Underline
on)
Character Size
EFRn = 0
EFRn = 1
(Fringe off)
(Fringe on)
VDSMD = 1 (Double scan mode)
Dot Size
Character Size
EFRn = 0
EFRn = 1
(Fringe off)
(Fringe on)
Small
1TOSC × 0.5THD
16TOSC × 9THD
16TOSC × 11THD
1TOSC × 1THD
16TOSC × 18THD
16TOSC × 20THD
Middle
2TOSC × 1THD
32TOSC × 18THD
32TOSC × 20THD
2TOSC × 2THD
32TOSC × 36THD
32TOSC × 40THD
Large
4TOSC × 2THD
64TOSC × 36THD
64TOSC × 40THD
4TOSC × 4THD
64TOSC × 72THD
64TOSC × 80THD
Small
1TOSC × 0.5THD
16TOSC × 12THD
16TOSC × 13THD
1TOSC × 1THD
16TOSC × 24THD
16TOSC × 25THD
Middle
2TOSC × 1THD
32TOSC × 24THD
32TOSC × 25THD
2TOSC × 2THD
32TOSC × 48THD
32TOSC × 50THD
Large
4TOSC × 2THD
64TOSC × 48THD
64TOSC × 50THD
4TOSC × 4THD
64TOSC × 96THD
64TOSC × 100THD
TOSC: One cycle of OSD oscillation, THD: One cycle of HD signal
88CS38B-156
2007-09-12
TMP88CS38B/CM38B/CP38B
Small
Middle
Large
Figure 2.15.11 Character Size
88CS38B-157
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Smoothing function
The smoothing function is used to make characters look smooth. Enabling
smoothing displays 1/4 dot between two dots connecting corner to corner within a
character. Small size character can not be enabled smoothing. Smoothing is
enabled by setting ESMZ (Bit4 in ORETC) in the OSD control register to “1”.
Smoothing specification unit:Display page
Smoothing specification register (1 bit)......ESMZ (Bit4 in ORETC)
“0”
“1”
....... Disable smoothing
....... Enable smoothing
Note: Data of the register is transferred to the OSD circuit and become valid when
the data is written.
Before
After
Before
After
Available form for smoothing
Invalid form for smoothing
Figure 2.15.12 Available Form and Invalid Form for Smoothing
Original character
Smoothing
Figure 2.15.13 Smoothing Example
88CS38B-158
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) Fringing function
The fringing function is used to display a character with a fringe width is 1 dot
in a different color from that of the character. When a character is displayed with
the maximum of 18 vertical dots and 16 horizontal dots, the fringe exceeds right
and left, top, and bottom of the character display area. If there is an adjacent
character that outer dot is active, then this dot will overrule the fringe in the
horizontal direction. Underlines are not fringed.
Fringing is enabled for each line by setting EFR1 to EFR8 (OREFR8) and EFR9
to EFR12 (OREFR12) in the OSD control register to “1”.
A color for fringe is specified common to all lines using OSD control registers,
IFDT, RFDT, GFDT, and BFDT (Bit3 to 0 in ORBK).
Fringing specification unit: Line
Fringing enable register (1 bit × 12) .... EFRn (n: 1 to 8) (OREFR8), EFRn (n: 9
to 12) (OREFR12)
“0”
....... Disable fringing
“1”
....... Enable fringing
Fringe colors: 8 or 15
Fringe color specification unit: Display page
Fringe color register (4 bits).....IFDT, RFDT, GFDT, BFDT (Bit3 to 0 in ORBK)
I signal function select: PISEL (Bit6 in ORETC)
“0”
“1”
....... 15 colors specification
I pin can be used to make a half level of R, G, B
signal (Dark color) through an extra circuit.
....... 8 colors specification
Contents of IDT register is disregarded.
I pin can be used as half transparency/half tone
through an extra circuit.
Note: The fringe of 1st column character does not exceed left, and the fringe of 32th
character does not exceed right.
88CS38B-159
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.15.5.4 Fringe Color (15 colors)
IFDT
0
1
RFDT
GFDT
BFDT
Figure Color
Black
0
0
0
0
0
1
Blue
0
1
0
Green
0
1
1
Cyan
1
0
0
Red
1
0
1
Magenta
1
1
0
Yellow
1
1
1
White
0
0
0
Black
0
0
1
Dark blue
0
1
0
Dark green
0
1
1
Dark cyan
1
0
0
Dark red
1
0
1
Dark magenta
1
1
0
Dark yellow
1
1
1
Gray
R, G, B pin output
R, G, B output
I pin output
Figure 2.15.14 Example Circuit for 15 Colors by I Pin.
88CS38B-160
2007-09-12
TMP88CS38B/CM38B/CP38B
Vertical indicate area
22 dots
Vertical indicate area
18 dots
2 dots
Before fringing
After fringing
Disable underline
Vertical indicate area
26 dots
Vertical indicate area
24 dots
2 dots
Before fringing
After fringing
Enable underline
a) Small character, NORMAL mode
Figure 2.15.15 (a) Fringing Example
88CS38B-161
2007-09-12
TMP88CS38B/CM38B/CP38B
Vertical indicate area
20 dots
Vertical indicate area
18 dots
1 dot
Before fringing
After fringing
Disable underline
Vertical indicate area
25 dots
Vertical indicate area
24 dots
1 dot
Before fringing
After fringing
Enable underline
b) Small character, double scan mode
Figure 2.15.16 (b) Fringing Example
88CS38B-162
2007-09-12
TMP88CS38B/CM38B/CP38B
Vertical indicate area
20 dots
Vertical indicate area
18 dots
1 dot
Before fringing
After fringing
Disable underline
Vertical indicate area
25 dots
Vertical indicate area
24 dots
1 dot
Before fringing
After fringing
Enable underline
c) Middle/Large character, NORMAL mode
Figure 2.15.17 (c) Fringing Example
88CS38B-163
2007-09-12
TMP88CS38B/CM38B/CP38B
Vertical indicate area
20 dots
Vertical indicate area
18 dots
1 dot
Before fringing
After fringing
Disable underline
Vertical indicate area
25 dots
Vertical indicate area
24 dots
1 dot
Before fringing
After fringing
Enable underline
d) Middle/Large character, double scan mode
Figure 2.15.18 (d) Fringing Example
88CS38B-164
2007-09-12
TMP88CS38B/CM38B/CP38B
(4) Background function
Background color function is used to color the entire background for the
character area (Refer to Table 2.15.4). Except the character area whose character
code is 000H.
This function is specified for each display page by setting EBKGD (Bit7 in
ORRCL) in the OSD control register to “1”.
A background color is specified for each display page by setting IBDT, RBDT,
GBDT, and BBDT (Bit7 to 4 in ORBK) in the OSD control registers.
Background specification unit: Display page
Background enable register (1 bit) ...... EBKGD (Bit7 in ORRCL)
“0”
....... Disable background
“1”
....... Enable background
Background color specification unit: Display page
Background color specification registers (4 bits) .... IBDT, RBDT, GBDT, BBDT
(Bit7 to 4 in ORBK)
I signal function select: PISEL (Bit6 in ORETC)
“0”
....... 15 colors specification
I pin can be used to make a half level of R, G, B
signal (Dark color) through an extra circuit.
“1”
....... 8 colors specification
Contents of IBDT register is disregarded.
I pin can be used as half transparency/half tone
through an extra circuit.
Table 2.15.5.5 Background Color (15 colors)
IBDT
0
1
RBDT
GBDT
BBDT
Background Color
Black
0
0
0
0
0
1
Blue
0
1
0
Green
Cyan
0
1
1
1
0
0
Red
1
0
1
Magenta
1
1
0
Yellow
1
1
1
White
0
0
0
Black
0
0
1
Dark blue
0
1
0
Dark green
Dark cyan
0
1
1
1
0
0
Dark red
1
0
1
Dark magenta
1
1
0
Dark yellow
1
1
1
Gray
88CS38B-165
2007-09-12
TMP88CS38B/CM38B/CP38B
R, G, B pin output
R, G, B output
I pin output
Figure 2.15.19 Example Circuit for 15 Colors by I Pin.
Character color: Cyan
Background color: Yellow
Scanning line
Scanning line
R
R
G
G
B
B
Y
Y
BL
BL
1) Disable background
2) Enable background
Figure 2.15.20 Background Function
Note: When the background function is enabled, the line enable the fringing function should not start with
a blank character. If it starts with a blank character, a fringe is displayed to the left of the blank
character.
88CS38B-166
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5.5 OSD Display Screen Control
(1) Display on/off
This function is used to display characters specified for on/off display.
Display on/off specification unit: Display page
Display on/off specification register (1 bit) ...... DON (Bit0 in ORDON)
“0”
....... Disable display
“1”
....... Enable display
Note: Do not start STOP mode during display is enable.
(2) Window function
This function is used to set upper and lower limit of display page. Window upper
limit is specified by WVSH (ORWVSH). Window lower limit is specified by WVSL
(ORWVSL). This function is enabled by setting EWDW (Bit1 in ORDON) in the
OSD control register to 1.
Window specification unit: Display page
Window function enable specification register (1 bit)...... EWDW (Bit1 in
ORDON)
“0”
....... Disable window function
“1”
....... Enable window function
Window upper limit specification register (9 bits) .....WVSH8 to 0 (ORWVSH)
Window lower limit specification register (9 bits)......WVSL8 to 0 (ORWVSL)
Window upper and lower limit position ......
When VDSMD is “0” (Normal mode):
WVSH = (WVSH8 to WVSH0) H × THD
WVSL = (WVSL8 to WVSL0) H × THD
When VDSMD is “1” (Double scan mode):
WVSH = (WVSH8 to WVSH0) H × 2THD
WVSL = (WVSL8 to WVSL0) H × 2THD
Note 1: THD: One cycle of HD signal
Note 2: WVSL > WVSH ≥ “1”
Note 3: Modify the value of window upper and lower limit register and the value of
EWDW during VD signal is low.
Note 4: It is recommendable that the window function is always enabled (EWDW = “1”)
and set WVSH to “01H”, WVSL to “1FEH”.
Note 5: Characters and symbols at scanning line specified by WVSL are not displayed.
88CS38B-167
2007-09-12
TMP88CS38B/CM38B/CP38B
HD
Background color
AVE2
Area plane color
Picture
WVSH
Raster color
SS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS
AHS1
SS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS
VD
SS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SS
WVSL
Picture
Window display: On, Area plane display: On, Background color display: On, Raster plane display: On
Correspond to Closed Caption
Display off
WVSH
Display
Figure 2.15.21 If WVSH is on a Code Plane
88CS38B-168
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) Full-raster blanking function
Full-raster blanking function is used to color the entire background for the
display area (TV screen). When using the full-raster blanking function, set
YBLCS (Bit2 in ORP6S) to “1”, output BL signal from Y/BL pin, because Y signal
cannot delete whole display page from video signal.
This function is specified for each display page by setting EXBL (Bit6 in
ORRCL) in the OSD register to “1”.
Full-raster blanking specification unit: Display page
Full-raster blanking enable register (1 bit) ..... EXBL (Bit6 in ORRCL)
“0”
....... Disable full-raster blanking
“1”
....... Enable full-raster blanking
Full-raster blanking color specification ........ RCLI, RCLR, RCLG, RCLB
(Bit3 to 0 in ORRCL)
registers (4 bits)
I signal function select: PISEL (Bit6 in ORETC)
“0”
“1”
....... 15 colors specification
I pin can be used to make a half level of R, G, B
signal (Dark color) through an extra circuit.
....... 8 colors specification
Contents of RCLI register is disregarded.
I pin can be used as half transparency/half tone
through an extra circuit.
Table 2.15.5.6 Raster Plane Color (15 colors)
RCLI
0
1
RCLR
RCLG
RCLB
Raster Plane Color
0
0
0
Black
0
0
1
Blue
0
1
0
Green
Cyan
0
1
1
1
0
0
Red
1
0
1
Magenta
1
1
0
Yellow
1
1
1
White
0
0
0
Black
0
0
1
Dark blue
0
1
0
Dark green
Dark cyan
0
1
1
1
0
0
Dark red
1
0
1
Dark magenta
1
1
0
Dark yellow
1
1
1
Gray
88CS38B-169
2007-09-12
TMP88CS38B/CM38B/CP38B
(4) Area plane function
Area plane function is used to display square area to two points on a screen.
Two planes operate independently. They are displayed according to the priority
(Area plane 1 > Area plane 2).
See area plane display position setting in section 2.15.5.3 (2) how to set display
positions for each area.
Each area plane is set to ON or OFF by AON2 and AON1 (Bit5 and bit4 in
ORRCL).
Area plane colors are set by ACLIx, ACLRx, ACLGx, ACLBx (Bit7 to bit0 in
ORACL, x: 1, 2).
Area plane colors: 8 or 15
Area plane specification unit: plane
Area plane color specification register (8 bits)
Area plane 1: ACLI1/ACLR1/ACLG1/ACLB1 (Bit3 to 0 in ORACL)
Area plane 2: ACLI2/ACLR2/ACLG2/ACLB2 (Bit7 to 4 in ORACL)
I signal function select: PISEL (Bit6 in ORETC)
“0”
....... 15 colors specification
I pin can be used to make a half level of R, G, B
signal (Dark color) through an extra circuit.
“1”
....... 8 colors specification
Contents of ACLI1 and ACLI2 register is
disregarded.
I pin can be used as half transparency/half tone
through an extra circuit.
Table 2.15.5.7 Area Plane Color (15 colors)
ACLIx
0
1
ACLRx
ACLGx
ACLBx
Area Plane Color
Black
0
0
0
0
0
1
Blue
0
1
0
Green
Cyan
0
1
1
1
0
0
Red
1
0
1
Magenta
1
1
0
Yellow
1
1
1
White
0
0
0
Black
0
0
1
Dark blue
0
1
0
Dark green
Dark cyan
0
1
1
1
0
0
Dark red
1
0
1
Dark magenta
1
1
0
Dark yellow
1
1
1
Gray
x: 1, 2
88CS38B-170
2007-09-12
TMP88CS38B/CM38B/CP38B
I signal function select
1.
Using for 15 colors (PISEL = 0)
Example color
Area plane
l=0
l=1
Red
Dark
red
Character
background
color
Green
Dark
green
Area plane
color
Blue
Dark
blue
Character
color
Scanning
line
Raster plane: Off
Character background: On
YBLCS: 0 (Y select)
R
15 colors
specification
G
B
I
Y
Figure 2.15.22 TV Display and OSD Signals (PISEL = 0)
88CS38B-171
2007-09-12
TMP88CS38B/CM38B/CP38B
Using for half transparency/half tone (PISEL = 1)
2.
Area plane: Half transparency/half tone
Scanning
line
Example color
Character
color
Red
Character
background
color
Green
Area plane
color
Blue
Raster plane: Off
Character background: On
YBLCS: 0 (Y select)
R
8 colors
specification
G
B
I
Y
Figure 2.15.23 TV Display and OSD Signals (PISEL = 1)
88CS38B-172
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5.6 Interrupt Control
(1) Display line counter
The display line counter indicates number of display line (s) by OSD circuit on
the TV screen. The display line counter is a 4-bit counter which is initialized to “0”
by the falling edge of the VD signal and which increments when last scanning of
each display line is completed (Falling edge of the HD signal). It is necessary to be
read out display line counter several times, because it does not synchronize CPU
clock.
Display line counter register (4 bits)..... DCTR (Bit3 to 0 in ORIRC)
“0000”......No display line is completed.
“0001”......1st display line is completed.
“0010”......2nd display line is completed.
.
.
..
..
“1111” ..... 15th display line is completed.
Display line
counter
1st Display Line
Display on
2nd Display Line
Display off
3rd Display Line
Display on
4th Display Line with all blank characters
Display on
•••
10th Display Line
Display on
11th Display Line
Display on
12th Display Line
Display on
12
11
10
9
4
3
2
1
0
m
VD signal
Note 1:
The display line counter also increments when a line with all blank characters or a line with display off is
specified.
Note 2:
When display lines are overlapped each other, previous display line is enabled and next line is canceled.
At this time, the display line counter does not increment for canceled line.
Figure 2.15.24 Display Line Counter
88CS38B-173
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Interrupt generator circuit
An interrupt request is generated when a falling edge of VD signal or when line
counter (DCTR) is counted to the certain value specified by ISDC.
Interrupt source select register (1 bit) ...SVD (Bit4 in ORIRC)
“0”
....... Interrupt request generated when the display line
counter (DCTR) is counted to the certain value which
is specified by ISDC.
....... Interrupt request is generated when a falling edge of
VD signal.
“1”
Interrupt generation line specification register (4 bits) ... ISDC (Bit3 to 0 in
ORIRC)
“0000”
“0001”
“0010”
.
.
.
“1111”
....... Interrupt request generated when the display line
counter is cleared.
....... Interrupt request generated at end points of the last
scanning line of the first display line
....... Interrupt request generated at end points of the last
scanning line of the 2nd display line
....... Interrupt request generated at end points of the last
scanning line of the 15th display line
2.15.5.7 Display Memory Access
(1) Display memory
The display memory is accessed for two purposes, one for writing data to the
display memory, and one for reading data from the display memory.
Display memory address specification registers .... DMA8 to MDA0 (ORDMA)
(9 bits)
Display memory data write registers
Character code write register (9 bits)
.... CRA8 to CRA0 (ORCRA)
Character ornamentation data write registers
.... SLNT, EUL, BLF, IDT, RDT,
(7 bits)
GDT, and BDT (ORDSN)
Display memory bank select register MBK (bit 1 in ORETC)
“0” ...
When writing either character code or character ornamentation data
“1” ...
When writing both character code and character ornamentation data
Note 1: These control registers have a characteristic that immediately when a value is
written to the register, the content of the register is transferred as valid data to
the OSD circuit/display memory.
Note 2: The data written to the display memory takes effect at the same time it is written.
When character code or character ornamentation data is written to the display
memory while it is displaying some character, the character may not be displayed
correctly. When writing data to the display memory, make sure no character is
being displayed in the memory location where you are going to write data.
Note 3: When writing data to or reading data from the display memory, do not use
two-byte transfer instructions such as “LDW(HL),mn LD rr, (pp)”. Otherwise,
erroneous data may be written to the display memory or data may be written to
an incorrect address.
Note 4: Allow for at least two instruction cycles between a display memory address
write instruction and a data write or read instruction. Also, when continuous
writing data to or reading data from the display memory, allow for at least two
instruction cycles between one write or read instruction and the next.
Otherwise, erroneous data may be written to the display memory or data may
be written to an incorrect address.
Note 5: When setting display memory addresses, always be sure to write all of 9
address bits sequentially in order of DMA8 and DMA7 to DMA0.
88CS38B-174
2007-09-12
TMP88CS38B/CM38B/CP38B
1.
Normal mode
In normal mode, the display memory addresses are automatically incremented
each time data is read from or written to the memory. Because addresses are
automatically incremented, this mode may be used for reading from or writing
data to multiple continuous addresses simultaneously.
<Display memory write sequence in normal mode>
a.
When writing either character code or character ornamentation data
(1) Set MFYWR, MBK, and RDWRV all to 0.
(2) Write the most significant address bit of the display memory to DMA8. Go on
and write the 8 low-order address bits of the display memory to DMA7 to
DMA0.
(3) Writing character code or character ornamentation data
•
Writing character code
Write the most significant bit of character code to CRA8. Go on and write
the 8 low-order bits of character code to CRA7 through CRA0. At this point in
time, the 9 bits of character code written are transferred to the display
memory, and DMA8 to DMA0 are automatically incremented.
•
Writing character ornamentation data
Write character ornamentation data to SLNT, EUL, BLF, IDT, RDT, GDT,
and BDT. At this point in time, the character ornamentation data written are
transferred to the display memory, and DMA8 to DMA0 are automatically
incremented.
(4) To write data (character code or character ornamentation data) to continuous
addresses, repeat step (3).
b.
When writing character code and character ornamentation data at a time
(1) Set MFYWR to 0, MBK to 1, and RDWRV to 0.
(2) Write the most significant address bit of the display memory to DMA8. Go on
and write the 8 low-order address bits of the display memory to DMA7 to
DMA0.
(3) Write character ornamentation data to SLNT, EUL, BLF, IDT, RDT, GDT, and
BDT. At this point in time, the character ornamentation written are
transferred to the display memory.
(4) Write the most significant bit of character code to CRA8. Go on and write the 8
low-order bits of character code to CRA7 to CRA0. At this point in time, the 9
bits of character code written and the character ornamentation data written
in step (3) are transferred to the display memory, and DMA8 to DMA0 are
automatically incremented.
(5) To write data to continuous addresses, repeat steps (3) and (4).
88CS38B-175
2007-09-12
TMP88CS38B/CM38B/CP38B
<Display memory read sequence in normal mode>
a.
When reading either character code or character ornamentation data
(1) Set MFYWR to 0, MBK to 0, and RDWRV to 1.
(2) Write the most significant address bit of the display memory to DMA8. Go on
and write the 8 low-order address bits of the display memory to DMA7 to
DMA0.
(3) Reading character code or character ornamentation data
•
Reading character code
Read the most significant bit of character code to CRA8. Go on and read the
8 low-order bits of character code to CRA7 to CRA0. At this point in time,
DMA8 to DMA0 are automatically incremented.
•
Reading character ornamentation data
Read character ornamentation data SLNT, EUL, BLF, IDT, RDT, GDT, and
BDT. At this point in time, DMA8 through DMA0 are automatically
incremented.
(4) To read data (character code or character ornamentation data) from
continuous addresses, repeat step (3).
b.
When reading character code and character ornamentation data at a time
(1) Set MFYWR to 0, MBK to 1, and RDWRV to 1.
(2) Write the most significant address bit of the display memory to DMA8. Go on
and write the 8 low-order address bits of the display memory to DMA7 to
DMA0.
(3) Read character ornamentation data SLNT, EUL, BLF, IDT, RDT, GDT, and
BDT.
(4) Read the most significant bit of character code to CRA8. Read the 8 low-order
bits of character code to CRA7 to CRA0. At this point in time, DMA8 to DMA0
are automatically incremented.
(5) To read data from continuous addresses, repeat steps (3) and (4).
2.
Read-modify-write mode
When writing data in read-modify-write mode, the display memory addresses
are automatically incremented as in normal mode, but when reading data in this
mode, the memory addresses are not automatically incremented.
Therefore, immediately after executing a read from some display memory
address, you can execute a write to the same display memory address. After
executing a write, the display memory addresses are automatically incremented.
a.
Reading/writing either character code or character ornamentation data in
read-modify-write mode
(1) Set MFYWR to 1 and MBK to 0, and RDWRV to 1.
(2) Write the most significant address bit of the display memory to DMA8. Go on
and write the 8 low-order address bits of the display memory to DMA7 to
DMA0.
(3) Reading character code or character ornamentation data
•
Reading character code
Read the most significant bit of character code to CRA8. Read the 8
low-order bits of character code to CRA7 to CRA0. DMA8 to DMA0 are not
incremented.
88CS38B-176
2007-09-12
TMP88CS38B/CM38B/CP38B
•
Reading character ornamentation data
Read character ornamentation data SLNT, EUL, BLF, IDT, RDT, GDT, and
BDT. DMA8 to DMA0 are not incremented.
(4) Writing character code or character ornamentation data
•
Set RDWRV to “0”.
•
Writing character code
Write the most significant bit of character code to CRA8. Go on and write
the 8 low-order bits of character code to CRA7 to CRA0. At this point in time,
the 9 bits of character code written are transferred to the display memory, and
DMA8 to DMA0 are automatically incremented.
•
Writing character ornamentation data
Write character ornamentation data to SLNT, EUL, BLF, IDT, RDT, GDT,
and BDT. At this point in time, the character ornamentation data written are
transferred to the display memory, and DMA8 to DMA0 are automatically
incremented.
(5) To continue executing read-modify-write operations, repeat steps (1) to (4). To
read/write data (Character code or character ornamentation data). To
continue executing read-modify-write mode from continuous addresses,
repeat steps (3) and (4).
b.
Reading/writing both character code and character ornamentation data in
read-modify-write mode
(1) Set MFYWR to 1, MBK to 1 and RDWRV to 1
(2) Write the most significant address bit of the display memory to DMA8. Go on
and write the 8 low-order address bits of the display memory to DMA7 to
DMA0.
(3) Read character ornamentation data SLNT, EUL, BLF, IDT, RDT, GDT, and
BDT. At this point in time, DMA8 to DMA0 are not incremented.
(4) Read the most significant bit of character code to CRA8. Read the 8 low-order
bits of character code to CRA7 to CRA0. At this point in time, DMA8 to DMA0
are not incremented.
(5) Set RDWRV to “0”.
(6) Write character ornamentation data to SLNT, EUL, BLF, IDT, RDT, GDT, and
BDT. At this point in time, the character ornamentation data written is
transferred to the display memory.
(7) Write the most significant bit of character code to CRA8. Go on and write the 8
low-order bits of character code to CRA7 to CRA0. At this point in time, the 9
bits of character code written and the character ornamentation data written
in step (6) are transferred to the display memory, and DMA8 to DMA0 are
automatically incremented.
(8) To continue executing read-modify-write operations, repeat steps (1) to (7). (To
read/write data to and from continuous addresses in read-modify-write mode,
repeat steps (3) to (7).)
88CS38B-177
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.15.5.8 Address Increment
RD (RDWRV = 1)
Character
Character
Ornamentation
Code
MFYWR = 0
MFYWR = 1
WR (RDWRV = 0)
Character
Character
Ornamentation
Code
MBK = 0
INC
INC
INC
MBK = 1
−
INC
−
INC
MBK = 0
−
−
INC
INC
MBK = 1
−
−
−
INC
INC
INC: Automatic address increment at read or write.
−:
Example:
1.
No address change at data read or write.
Setting a character code (020H) to the display memory (Address: 120H) and setting (001H) for a
character ornamentation.
MBK = 0
; Set display memory address
LD
(0x25),
0x01
; ORDMA<DMA8>
LD
(0x24),
0x20
; ORDMA<DMA7:0>
; Set character code
LD
(0x1F),
0x00
; ORCRA<CRA8>
LD
(0x1E),
0x20
; ORCRA<CRA7:0>
; Set display memory address again
LD
(0x25),
0x01
LD
(0x24),
0x20
; Set character ornamentation
LD
2.
(0x1D),
0X01
; ORDSN<SLNT, ..... BDT>
MBK = 1
; Set display memory address
LD
(0x25),
0x01
LD
(0x24),
0x20
; Set character ornamentation
LD
(0x1D),
0X01
; Set character code
LD
(0x1F),
0x00
LD
(0x1E),
0x20
Note 1: To write character code into the display memory, first write into register CRA8 and then
write into registers CRA7 to CRA0. When data is written into registers CRA7 to CRA0,
DMA8 to DMA0 is incremented. It is impossible to write into the display memory for
CRA7 to CRA0 alone. If no data is written into register CRA8 while data is written into
registers CRA7 to CRA0, the value previously written into register CRA8 is written into
the associated display memory.
Note 2: To read character code from the display memory, first read from register CRA8, and
then read from registers CRA7 to CRA0. When data is read from registers CRA7 to
CRA0, DMA8 to DMA0 is incremented.
Note 3: There should be a time interval of at least two machine cycles between a DMA set
instruction and a data write/read instruction. There should be a time interval of at least
two machine cycles between a data write instruction and a data read instruction.
(2) Character
Characters: 384 (including blank character)
Character specification register (9 bits) ...........CRA8 to CRA0 (Bit8 to 0 in ORCRA)
Character code “000H” ............................Blank character
Character code “001H” to “017FH” ........User programmable by character
ROM
88CS38B-178
2007-09-12
TMP88CS38B/CM38B/CP38B
(3) Character color
Character colors: 8 or 15
Character color specification unit: Character
Character color specification register (4 bits): IDT/RDT/GDT/BDT (Bit3 to 0 in
ORDSN)
I signal function select: PISEL (Bit6 in ORETC)
“0”
....... 15 colors specification
I pin can be used to make a half level of R, G, B
signal (Dark color) through an extra circuit.
“1”
....... 8 colors specification
Contents of IDT register is disregarded.
I pin can be used as half transparency/half tone
through an extra circuit.
Table 2.15.5.9 Character Color (15 colors)
IDT
0
1
RDT
GDT
BDT
Character Color
0
0
0
Black
0
0
1
Blue
0
1
0
Green
0
1
1
Cyan
1
0
0
Red
1
0
1
Magenta
1
1
0
Yellow
White
1
1
1
0
0
0
Black
0
0
1
Dark blue
0
1
0
Dark green
0
1
1
Dark cyan
1
0
0
Dark red
1
0
1
Dark magenta
1
1
0
Dark yellow
1
1
1
Gray
R, G, B pin output
R, G, B output
I pin output
Figure 2.15.25 Example of Circuit for 15 Color by I Pin
88CS38B-179
2007-09-12
TMP88CS38B/CM38B/CP38B
(4) Blinking function
Blinking function is used to blink display characters.
When BKMF is “1”, characters specified for blinking by BLF are not displayed. (If
the background color function is used, the background color is not disappeared.)
Blinking specification unit: Character
Blinking specification register (1 bit).....BLF (Bit4 in ORDSN)
“0”
....... No blinking
“1”
....... Blinking
Blinking master specification register (1 bit).....BKMF (Bit5 in ORETC)
“0”
“1”
Note:
....... Disable blinking
....... Enable blinking (Characters whose BLF are set to
“1” are not displayed.)
Regarding the extra dot of the left and/or right character by fringing function, it is not
enabled as blink.
(5) Underline function
Underline function is used to add a line under a display character. The underline is
same color as that of character.
Underline specification unit: Character/line
Underline enable register (Character unit) (1 bit).....EUL (Bit5 in ORDSN)
“0”
....... No underline
“1”
....... Underline
Underline enable register (Line unit) (1 bit × 12)
Underline colors: 8 or 15
Underline color specification registers (4 bits)
Note:
......EULAn (n: 1 to 8)(OREULA8),
EULAn (n: 9 to 12)
(OREULA12)
......RDT, GDT, BDT, IDT (Bit3 to 0 in
ORDSN) (Refer to Table 2.15.5.9)
To use the underline function, set both the underline enable register for underlining
text in characters and that for underlining text in lines. If the former register (EUL)
only is set, an underline is not displayed.
16
18
Character display area
6
Underline display area
24
EUL = 0
EUL = 1
Figure 2.15.26 Underline
88CS38B-180
2007-09-12
TMP88CS38B/CM38B/CP38B
(6) Solid space control
Solid space control is used to display one column of solid space to the left and right of
32 columns.
Solid space control is used to delete the video signal in the areas where solid spaces
are located in the original display page, then add color to them.
Solid space specification unit: line
Solid space specification register (24 bits)
For line 1
For line 2
..
.
For line 12
SOL11 and SOL10 (Bits 1 and 0 in ORSOL4)
SOL21 and SOL20 (Bits 3 and 2 in ORSOL4)
..
.
SOL121 and SOL120 (Bits 7 and 6 in ORSOL12)
Solid space specification
The solid space control functions as follows:
SOLx1/SOLx0 (x: 1 to 12)
“00”
.......
“01”
.......
“10”
.......
“11”
.......
No solid space display
Solid space display left for 32 columns
Solid space display right for 32 columns
Solid space display left and right for 32 columns
Solid space color specification registers (4 bits)
....... IBDT, RBDT, GBDT, BBDT (Bits 3 to 0 in ORBK)
(Same color as that of background)
32 columns
Solid space
(Left)
Solid space
(Right)
Figure 2.15.27 Solid Space
88CS38B-181
2007-09-12
TMP88CS38B/CM38B/CP38B
(7) Slant function
Slant function is used to slant characters for italics.
Slant specification unit: Character
Slant enable register (1 bit) .....SLNT (Bit6 in ORDSN)
“0”
“1”
....... No slant
....... Slant
Note 1: SLANT function is enabled each characters, and therefore, in case of using
background function, this color of the Background is enable as slant. Regarding
the extra dots of the left and/or right character by fringing function, it is not
enabled as slant.
Note 2: When a character is slanted in an area, which overlaps with the character field,
the overlap is also slanted.
Note 3: If slanting a character causes part of the character to get into the character field to
the immediate right of the character, then this part is not displayed.
Note 4: To provide closed caption display (CCD), specify black as the background color,
and set YBLCS to “1”. R, G, B and Y are all slanted. Thus, if the Y signal is
selected, a video signal is displayed above and to the left of the slant character.
Note 5: When a character is slanted, the dot data to the immediate left of the character is
also slanted.
The same color as that of the dot on the left is displayed.
When an entire character field (including its
background) contains dots:
When the character field on the right
does not contain a dots:
Figure 2.15.28 Slant
88CS38B-182
2007-09-12
TMP88CS38B/CM38B/CP38B
2.15.5.8 OSD Control Registers
Can not access all OSD control registers in any of read-modify-write instructions
such as bit operation, etc.
0RHS1
7
6
5
4
3
2
1
0
(00F81H)
HS17
HS16
HS15
HS14
HS13
HS12
HS11
HS10
(Initial value: 0000 0000)
Write
only
Horizontal display start position specification
7
6
5
4
3
2
1
0
(00F82H)
VS17
VS16
VS15
VS14
VS13
VS12
VS11
VS10
(Initial value: 0000 0000)
(00F83H)
−
−
−
−
−
−
−
VS18
(Initial value: **** ***0)
ORVS2
(00F84H)
VS27
VS26
VS25
VS24
VS23
VS22
VS21
VS20
(Initial value: 0000 0000)
(00F85H)
−
−
−
−
−
−
−
VS28
(Initial value: **** ***0)
ORVS3
(00F86H)
VS37
VS36
VS35
VS34
VS33
VS32
VS31
VS30
(Initial value: 0000 0000)
(00F87H)
−
−
−
−
−
−
−
VS38
(Initial value: **** ***0)
ORVS4
(00F88H)
VS47
VS46
VS45
VS44
VS43
VS42
VS41
VS40
(Initial value: 0000 0000)
(00F89H)
−
−
−
−
−
−
−
VS48
(Initial value: **** ***0)
ORVS5
(00F8AH)
VS57
VS56
VS55
VS54
VS53
VS52
VS51
VS50
(Initial value: 0000 0000)
(00F8BH)
−
−
−
−
−
−
−
VS58
(Initial value: **** ***0)
ORVS6
(00F8CH)
VS67
VS66
VS65
VS64
VS63
VS62
VS61
VS60
(Initial value: 0000 0000)
(00F8DH)
−
−
−
−
−
−
−
VS68
(Initial value: **** ***0)
ORVS7
(00F8EH)
VS77
VS76
VS75
VS74
VS73
VS72
VS71
VS70
(Initial value: 0000 0000)
(00F8FH)
−
−
−
−
−
−
−
VS78
(Initial value: **** ***0)
ORVS8
(00F90H)
VS87
VS86
VS85
VS84
VS83
VS82
VS81
VS80
(Initial value: 0000 0000)
(00F91H)
−
−
−
−
−
−
−
VS88
(Initial value: **** ***0)
ORVS9
(00F92H)
VS97
VS96
VS95
VS94
VS93
VS92
VS91
VS90
(Initial value: 0000 0000)
(00F93H)
−
−
−
−
−
−
−
VS98
(Initial value: **** ***0)
ORVS10
(00F94H)
VS107
VS106
VS105
VS104
VS103
VS102
VS101
VS100
(Initial value: 0000 0000)
(00F95H)
−
−
−
−
−
−
−
VS108
(Initial value: **** ***0)
ORVS11
(00F96H)
VS117
VS116
VS115
VS114
VS113
VS112
VS111
VS110
(Initial value: 0000 0000)
(00F97H)
−
−
−
−
−
−
−
VS118
(Initial value: **** ***0)
ORVS12
(00F98H)
VS127
VS126
VS125
VS124
VS123
VS122
VS121
VS120
(Initial value: 0000 0000)
(00F99H)
−
−
−
−
−
−
−
VS128
(Initial value: **** ***0)
ORVS1
VSn8 to
VSn0
Vertical display start position for line n
Write
only
(n: 1 to 12)
Note 1:
If display lines are overlapped each other, previous display line is enabled and next line is disabled. Set
the vertical display start position not to overlap display lines.
Note 2:
Transfer the contents of vertical display start position registers into OSD circuit before a position of the
scanning line coincides with their own vertical display start position.
88CS38B-183
2007-09-12
TMP88CS38B/CM38B/CP38B
ORCS4
(00F9AH)
ORCS8
(00F9BH)
ORCS12
(00F9CH)
7
6
5
4
3
2
1
0
CS4
CS3
CS2
CS1
(Initial value: 0000 0000)
CS8
CS7
CS6
CS5
(Initial value: 0000 0000)
CS12
CS11
CS10
CS9
(Initial value: 0000 0000)
00:
01:
10:
11:
Character size and display
on/off for line n
CSn
Display off
Large size
Middle size
Small size
Write
only
(n: 1 to 12)
OREULA8
(00F9DH)
OREULA12
(00F9EH)
EULA8
EULA7
EULA6
EULA5
−
−
−
−
EULA1
(Initial value: 0000 0000)
EULA12 EULA11 EULA10 EULA9
EULA4
(Initial value: **** 0000)
Underline for display line for
line n
EULAn
EULA3
0:
1:
EULA2
Display off
Display on
(n: 1 to 12)
OREFR8
(00F9FH)
OREFR12
(00FA0H)
EFR8
EFR7
EFR6
EFR5
EFR4
EFR3
EFR2
EFR1
(Initial value: 0000 0000)
−
−
−
−
EFR12
EFR11
EFR10
EFR9
(Initial value: **** 0000)
EFRn
Fringing enable specification
register for line n
0:
1:
Write
only
Disable fringing
Enable fringing
(n: 1 to 12)
Note: When a display line is enabled fringing function, its vertical size is increased by one dot (by two dots when its
character size is small) independent of its character font. Therefore, when a vertical display start position is
specified to no space between the lines, the display line which is overlapped with increasing dot(s) is canceled.
ORSLO4
(00FA2H)
ORSLO8
(00FA3H)
ORSLO12
(00FA4H)
SLO4
SLO3
SLO2
SLO1
(Initial value: 0000 0000)
SLO8
SLO7
SLO6
SLO5
(Initial value: 0000 0000)
SLO12
SLO11
SLO10
SLO9
(Initial value: 0000 0000)
SLOn
Solid space for line n
00:
01:
10:
11:
No solid space display
Solid space display left
Solid space display right
Solid space display left and right
Write
only
(n: 0 to 12)
88CS38B-184
2007-09-12
TMP88CS38B/CM38B/CP38B
ORBK
(00FA5H)
7
6
5
4
3
2
1
0
IBDT
RBDT
GBDT
BBDT
IFDT
RFDT
GFDT
BFDT
IBDT/
RBDT/
GBDT/
BBDT
IFDT/
RFDT/
GFDT/
BFDT
Background color select
Fringing color select
0000:
0001:
0010:
0011:
0100:
0101:
0110:
0111:
1000:
1001:
1010:
1011:
1100:
1101:
1110:
1111:
0000:
0001:
0010:
0011:
0100:
0101:
0110:
0111:
1000:
1001:
1010:
1011:
1100:
1101:
1110:
1111:
Black
Blue
Green
Cyan
Red
Magenta
Yellow
White
Black
Dark blue
Dark green
Dark cyan
Dark red
Dark magenta
Dark yellow
Gray
Black
Blue
Green
Cyan
Red
Magenta
Yellow
White
Black
Dark blue
Dark green
Dark cyan
Dark red
Dark magenta
Dark yellow
Gray
(Initial value: 0000 0000)
Write
only
Note: Set IBDT and IFDT to 1 when PISEL (Bit6 in ORETC) sets to 1. Then background color select and fringing
color select are 8 variety.
88CS38B-185
2007-09-12
TMP88CS38B/CM38B/CP38B
ORACL
(00FA6H)
7
6
5
4
3
2
1
0
ACLI2
ACLR2
ACLG2
ACLB2
ACLI1
ACLR1
ACLG1
ACLB1
ACLI2/
ACLR2/
ACLG2/
ACLB2
ACLI1/
ACLR1/
ACLG1/
ACLB1
Area 2 plane color select
Area 1 plane color select
ACLI2
ACLI1
(Initial value: 0000 0000)
0000: Black
0001: Blue
0010: Green
0011: Cyan
0100: Red
0101: Magenta
0110: Yellow
0111: White
1000: Black
1001: Dark blue
1010: Dark green
1011: Dark cyan
1100: Dark red
1101: Dark magenta
1110: Dark yellow
1111: Gray
0000: Black
0001: Blue
0010: Green
0011: Cyan
0100: Red
0101: Magenta
0110: Yellow
0111: White
1000: Black
1001: Dark blue
1010: Dark green
1011: Dark cyan
1100: Dark red
1101: Dark magenta
1110: Dark yellow
1111: Gray
0: Not assign half transparency for area 2 plane
1: Assign half transparency for area 2 plane
0: Not assign half transparency for area 1 plane
1: Assign half transparency for area 1 plane
Write
only
Note: Set ACLI2 and ACLI1 to 1 when PISEL (Bit6 in ORETC) sets to 1. Then area 2 plane color select and area 1
plane color select are 8 variety.
88CS38B-186
2007-09-12
TMP88CS38B/CM38B/CP38B
ORIV
(00FBBH)
7
6
VDPOL HDPOL
5
4
3
2
1
0
YBLII
RGBII
YIV
BLIV
RGBIV
IIV
VDPOL
VD input polarity select
HDPOL
HD input polarity select
YBLII
Y/BLIN input polarity select
RGBII
RIN, GIN, BIN input polarity
select
YIV
Y output polarity select
BLIV
BL output polarity select
RGBIV
0:
1:
0:
1:
0:
1:
0:
1:
0:
1:
0:
1:
0:
1:
0:
1:
R, G, B output polarity select
IIV
I output polarity select
(Initial value: 0000 0000)
Non-invert input signal
Invert input signal
Non-invert input signal
Invert input signal
Active high
Active low
Active high
Active low
Active high
Active low
Active high
Active low
Active high
Active low
Active high
Active low
Write
only
ORDMA
7
6
5
4
3
2
1
0
(00024H)
DMA7
DMA6
DMA5
DMA4
DMA3
DMA2
DMA1
DMA0
(Initial value: 0000 0000)
(00025H)
−
−
−
−
−
−
−
DMA8
(Initial value: **** ***0)
DMAn
Write
only
Display memory address
(n: 0 to 8)
Note:
It necessary to write all bits of display memory address, writng DMA7 to DMA0 after DMA8, when writing
display address.
ORDSN
7
6
5
4
3
2
1
0
(0001DH)
−
SLNT
EUL
BLF
IDT
RDT
GDT
BDT
Slant enable specification
register
0:
1:
Disable slant
Enable slant
EUL
Underline enable specification
register
0:
1:
Disable underline
Enable underline
BLF
Blinking enable specification
register
0: Disable blinking
1: Enable blinking
0000: Black
0001: Blue
0010: Green
0011: Cyan
0100: Red
0101: Magenta
0110: Yellow
0111: White
1000: Black
1001: Dark blue
1010: Dark green
1011: Dark cyan
1100: Dark red
1101: Dark magenta
1110: Dark yellow
1111: Gray
SLNT
IDT/
RDT/
GDT/
BDT
Note:
Character color select
(Initial value: **** ****)
Read/
Write
Set IDT to 1 when PISEL (Bit6 in ORETC) sets to 1. Then character color select is 8 variety.
88CS38B-187
2007-09-12
TMP88CS38B/CM38B/CP38B
7
6
5
4
3
2
1
0
(0001EH)
CRA7
CRA6
CRA5
CRA4
CRA3
CRA2
CRA1
CRA0
(Initial value: **** ****)
(0001FH)
−
−
−
−
−
−
−
CRA8
(Initial value: **** ****)
ORCRA
CRAn
Read/
Write
Character code
(n: 0 to 8)
Note:
ORWVSH
(00FBCH)
(00FBDH)
Write or read CRA7 to CRA0 after write or read CRA8.
7
6
5
4
3
2
1
0
WVSH7 WVSH6 WVSH5 WVSH4 WVSH3 WVSH2 WVSH1 WVSH0
−
−
WVSLn
−
−
−
−
−
WVSH8
(Initial value: 0000 0000)
(Initial value: **** ***0)
Write
only
Window upper limit position
(n: 0 to 8)
ORWVSL
(00FBEH)
(00FBFH)
7
6
5
4
3
2
1
0
WVSL7 WVSL6 WVSL5 WVSL4 WVSL3 WVSL2 WVSL1 WVSL0
−
−
WVSLn
−
−
−
−
−
WVSL8
(Initial value: 0000 0000)
(Initial value: **** ***0)
Write
only
Window lower limit position
(n: 0 to 8)
ORDON
7
6
5
4
3
2
1
0
(00F80H)
−
−
−
−
−
RGWR
EWDW
DON
RGWR
Written data transfer control
EWDW
Window enable specification
register
DON
Display on/off select
0:
1:
0:
1:
0:
1:
(Initial value: **** *000)
(Initial state)
Transfers written data to OSD circuit
(after transfer, RGWR is reset to 0)
Disable window function
Enable window function
Disable display
Enable display
88CS38B-188
Read/
Write
2007-09-12
TMP88CS38B/CM38B/CP38B
ORRCL
(00FA7H)
7
6
5
4
3
2
1
0
EBKGD
EXBL
AON2
AON1
RCLI
RCLR
RCLG
RCLB
Background function enable
specification register
0:
1:
No background function
Background function enable
EXBL
Full-raster blanking enable
specification register
0:
1:
No Full-raster blanking
Full-raster blanking
AON2
Area 2 plane display enable
specification register
0:
1:
No area 2 plane display
Area 2 plane display enable
AON1
Area 1 plane display enable
specification register
0: No area 1 plane display
1: Area 1 plane display enable
0000: Black
0001: Blue
0010: Green
0011: Cyan
0100: Red
0101: Magenta
0110: Yellow
0111: White
1000: Black
1001: Dark blue
1010: Dark green
1011: Dark cyan
1100: Dark red
1101: Dark magenta
1110: Dark yellow
1111: Gray
EBKGD
RCLI
RCLR/
RCLG/
RCLB
Note:
Raster plane color select
(Initial value: 0000 0000)
Write
only
Set RCLI to 1 when PISEL (Bit6 in ORETC) sets to 1. Then transfer plane select is 8 variety.
88CS38B-189
2007-09-12
TMP88CS38B/CM38B/CP38B
ORAHS1
7
6
5
4
3
2
1
0
(00FA8H)
AHS17
AHS16
AHS15
AHS14
AHS13
AHS12
AHS11
AHS10
(Initial value: 0000 0000)
(00FA9H)
−
−
−
−
−
−
−
AHS18
(Initial value: **** ***0)
ORAHE1
(00FAAH)
AHE17
AHE16
AHE15
AHE14
AHE13
AHE12
AHE11
AHE10
(Initial value: 0000 0000)
(00FABH)
−
−
−
−
−
−
−
AHE18
(Initial value: **** ***0)
AHS1n
Horizontal start point for area 1 plane
AHE1n
Horizontal end point for area 1 plane
Write
only
(n: 0 to 8)
ORAVS1
(00FACH)
AVS17
AVS16
AVS15
AVS14
AVS13
AVS12
AVS11
AVS10
(Initial value: 0000 0000)
(00FADH)
−
−
−
−
−
−
−
AVS18
(Initial value: **** ***0)
ORAVE1
(00FAEH)
AVE17
AVE16
AVE15
AVE14
AVE13
AVE12
AVE11
AVE10
(Initial value: 0000 0000)
(00FAFH)
−
−
−
−
−
−
−
AVE18
(Initial value: **** ***0)
AVS1n
Vertical start point for area 1 plane
AVE1n
Vertical end point for area 1 plane
Write
only
(n: 0 to 8)
ORAHS2
(00FB0H)
AHS27
AHS26
AHS25
AHS24
AHS23
AHS22
AHS21
AHS20
(00FB1H)
−
−
−
−
−
−
−
AHS28
ORAHE2
(00FB2H)
AHE27
AHE26
AHE25
AHE24
AHE23
AHE22
AHE21
AHE20
(Initial value: 0000 0000)
(00FB3H)
−
−
−
−
−
−
−
AHE28
(Initial value: **** ***0)
AHS2n
Horizontal start point for area 2 plane
AHE2n
Horizontal end point for area 2 plane
Write
only
(n: 0 to 8)
ORAVS2
(00FB4H)
AVS27
AVS26
AVS25
AVS24
AVS23
AVS22
AVS21
AVS20
(Initial value: 0000 0000)
(00FB5H)
−
−
−
−
−
−
−
AVS28
(Initial value: **** ***0)
ORAVE2
(00FB6H)
AVE27
AVE26
AVE25
AVE24
AVE23
AVE22
AVE21
AVE20
(Initial value: 0000 0000)
(00FB7H)
−
−
−
−
−
−
−
AVE28
(Initial value: **** ***0)
AVS2n
Vertical start point for area 2 plane
AVE2n
Vertical end point for area 2 plane
Write
only
(n: 0 to 8)
88CS38B-190
2007-09-12
TMP88CS38B/CM38B/CP38B
ORP6S
(00FBAH)
7
6
5
4
3
2
P67S
P66S
P65S
P64S
PIDS
YBLCS
P67S to
P64S
ORETC
(00FB8H)
I pin output select
YBLCS
Y/BL signal select
MPXS
R, G, B, Y/BL signal select
0
MPXS
(Initial value: 0000 0000)
0:
1:
0:
1:
0:
1:
00:
R, G, B, Y/BL signal output
P67 to P64 port output
I signal output
P57 port output
Y signal output
BL signal output
Simultaneous output (Signal from the OSD circuit has
higher priority)
01: Output of signal from internal OSD circuit
10: Output of signal from externally input
11: Simultaneous output (Externally input signal has
higher priority)
P6 port output select
PIDS
1
7
6
5
4
3
2
1
0
VDSMD
PISEL
BKMF
ESMZ
“0”
MFYWR
MBK
RDWRV
VDSMD
Scan mode select
PISEL
I pin function select
BKMF
Blinking master
ESMZ
Smoothing enable specification
register
MFYWR
Display memory bank
switching
MBK
RDWRV
Note:
Display memory read mode
select
Read/write mode select
(Initial value: 0000 0000)
0:
1:
0:
1:
0:
1:
0:
1:
Normal mode
Double scan mode
15 colors
Half transparency/half tone
Double blinking
Enable blinking
Disable smoothing
Enable smoothing
0:
1:
0:
Normal mode
Read-modify-write mode
Access to either character code or character display
options
Access both character display option and character
code
Data write mode for display memory
Data read mode for display memory
1:
0:
1:
Write
only
Write
only
Clear “0” to bit3 in ORETC.
88CS38B-191
2007-09-12
TMP88CS38B/CM38B/CP38B
ORIRC
7
6
5
4
(00FB9H)
−
−
−
SDV
SVD
ISDC
ORIRC
(00FB9H)
−
DCTR
Note 1:
3
Interrupt generation line select
−
−
Display line counter
1
0
ISDC
Interrupt source select
−
2
(Initial value: ***0 0000)
0: Interrupt request by ISDC value
1: Interrupt request at falling edge of VD signal
When the line display of the ISDC value ends (with the
falling edge of HD signal)
while SVD = 0, interrupt request is generated.
0000: Request interrupt when display of low-order 4 bits
“0000” of DCTR ends.
0001: Low-order 4 bits “0001” of DCTR
0010: Low-order 4 bits “0010” of DCTR
0011: Low-order 4 bits “0011” of DCTR
0100: Low-order 4 bits “0100” of DCTR
0101: Low-order 4 bits “0101” of DCTR
0110: Low-order 4 bits “0110” of DCTR
0111: Low-order 4 bits “0111” of DCTR
1000: Low-order 4 bits “1000” of DCTR
1001: Low-order 4 bits “1001” of DCTR
1010: Low-order 4 bits “1010” of DCTR
1011: Low-order 4 bits “1011” of DCTR
1100: Low-order 4 bits “1100” of DCTR
1101: Low-order 4 bits “1101” of DCTR
1110: Low-order 4 bits “1110” of DCTR
1111: Low-order 4 bits “1111” of DCTR
DCTR
Write
only
(Initial value: **** 0000)
0000: No line display or when the display of the 16th line
ends.
0001: 1st line display ends.
0010: 2nd line display ends.
0011: 3rd line display ends.
0100: 4th line display ends.
0101: 5th line display ends.
0110: 6th line display ends.
0111: 7th line display ends.
1000: 8th line display ends.
1001: 9th line display ends.
1010: 10th line display ends.
1011: 11th line display ends.
1100: 12th line display ends.
1101: 13th line display ends.
1110: 14th line display ends.
1111: 15th line display ends.
Read
only
The display line counter also increments when a line with all blank data or a line with display off is specified.
If display lines are overlapped each other, previous display line is enabled and next line is disabled. At this
time, the display line counter for canceled line does not increment.
Note 2:
*: Don’t care.
Note 3:
All OSD control registers cannot use the read-modify-write instructions. (Bit manipulation instructions such
as SET, CLR, etc. and logical operation such as AND, OR, etc.)
88CS38B-192
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.15.5.10 OSD Control Register List (1/2)
Register
Address
Register
Name
00F81
00F82,
00F83 to
00F98,
00F99
00F9A
00F9B
00F9C
00F9D
00F9E
00F9F
00FA0
00FA2
00FA3
00FA4
00FA5
ORHS1
ORVSn
ORCS4
ORCS8
ORCS12
OREULA8
OREULA12
OREFR8
OREFR12
ORSOL4
ORSOL8
ORSOL12
ORBK
00FA6
Register Bit Configuration
Bit4
Bit3
Bit2
Bit7
Bit6
Bit5
HS17
VSn7
−
HS16
VSn6
−
HS15
VSn5
−
HS14
VSn4
−
HS13
VSn3
−
HS12
VSn2
−
Bit0
HS10
VSn0
VSn8
CS4
CS8
CS12
EULA8
EULA7
−
−
EFR8
EFR7
−
−
SOL4
SOL8
SOL12
IBDT
RBDT
CS3
CS7
CS11
EULA6
EULA5
−
−
EFR6
EFR5
−
−
SOL3
SOL7
SOL11
GBDT
BBDT
ORACL
ACLI2
ACLR2
ACLG2
ACLB2
ACLI1
ACLR1
ACLG1
ACLB1
00FA7
CRRCL
EBKGD
EXBL
AON2
AON1
RCLI
RCLR
RCLG
RCLB
00FA8
00FA9
00FAA
00FAB
00FAC
00FAD
00FAE
00FAF
00FB0
00FB1
00FB2
00FB3
00FB4
00FB5
00FB6
00FB7
00FB8
ORAHS1
ORETC
AHS17
−
AHE17
−
AVS17
−
AVE17
−
AHS27
−
AHE27
−
AVS27
−
AVE27
−
VDSMD
AHS16
−
AHE16
−
AVS16
−
AVE16
−
AHS26
−
AHE26
−
AVS26
−
AVE26
−
PISEL
AHS15
−
AHE15
−
AVS15
−
AVE15
−
AHS25
−
AHE25
−
AVS25
−
AVE25
−
BKMF
AHS14
−
AHE14
−
AVS14
−
AVE14
−
AHS24
−
AHE24
−
AVS24
−
AVE24
−
ESMZ
AHS13
−
AHE13
−
AVS13
−
AVE13
−
AHS23
−
AHE23
−
AVS23
−
AVE23
−
“0”
AHS12
−
AHE12
−
AVS12
−
AVE12
−
AHS22
−
AHE22
−
AVS22
−
AVE22
−
MFYWR
AHS11
−
AHE11
−
AVS11
−
AVE11
−
AHS21
−
AHE21
−
AVS21
−
AVE21
−
MBK
AHS10
AHS18
AHE10
AHE18
AVS10
AHS18
AVE10
AVE18
AHS20
AHS28
AHE20
AHE28
AVS20
AHS28
AVE20
AVE28
RDWRV
00FB9
ORIRC
−
−
−
SVD
00FB9
00FBA
ORIRC
ORP6S
−
P67S
−
P66S
−
P65S
−
P64S
ORAHE1
ORAVS1
ORAVE1
ORAHS2
ORAHE2
ORAVS2
ORAVE2
CS2
CS6
CS10
EULA4
EULA3
EULA12 EULA11
EFR4
EFR3
EFR12
EFR11
SOL2
SOL6
SOL10
IFDT
RFDT
Bit1
HS11
VSn1
−
CS1
CS5
CS9
EULA2
EULA1
EULA10
EULA9
EFR2
EFR1
EFR10
EFR9
SOL1
SOL5
SOL9
GFDT
BFDT
ISDC
PIDS
DCTR
YBLCS
88CS38B-193
MPXS
Bit Contents
HS17 to 10: Code horizontal display base position setting
VSn8 to 0: Code vertical display position setting
(n: 0 to 12)
CSn: Character size (n: 1 to 12)
00: Display off
10: Middle size
01: Large size
11: Small size
EULAn: Underline display setting for line n (n: 0 to 12)
EFRn: Fringing setting for line n (n: 0 to 12)
SOLn: Solid space display setting for line n (n: 0 to 12)
00: No solid space
10: Right
01: Left
11: Left and right
IBDT, RBDT, GBDT, BBDT: Background color setting
IFDT, RFDT, GFDT, BFDT: Fringing color setting
ACLI2/ACLR2/ACLG2/ACLB2: Area 2 plane color
ACLI1/ACLR1/ACLG1/ACLB1: Area 1 plane color
Set ACLI2 and SCLI1 to 1, when PISEL 1
EBKGD: Background function
EXBL: Full-raster blanking
AON2: Area 2 plane display
AON1: Area 1 plane display
RCLI/R/G/B: Raster plane color
Set RCLI to 1, when PISEL 1
AHSx: Area 1 plane horizontal start position (n: 0 to 8)
AHE1x: Area 1 plane horizontal end position (n: 0 to 8)
AVS1x: Area 1 plane vertical start position (n: 0 to 8)
AVE1x: Area 1 plane vertical end position (n: 0 to 8)
AHS2x: Area 2 plane horizontal start position (n: 0 to 8)
AHE2x: Area 2 plane horizontal end position (n: 0 to 8)
AVS2x: Area 2 plane vertical start position (n: 0 to 8)
AVE2x: Area 2 plane vertical end position (n: 0 to 8)
VDSMD: Scan mode select
PISEL: I pin function select
BKMF: Blinking master
ESMZ: Smoothing
MFYWR: Display memory read mode select
MBK: Display memory bank switching select
RDWRV: Read/write mode select at normal mode
SVD: Interrupt source select
ISDC: Interrupt generation line select
DCTR: Display line counter
P6xS: P6 port output select (x: 4 to 7)
PIDS: I pin output select
YBLCS: Y/BL signal select
MPXS: R, G, B, Y/BL single select
2007-09-12
TMP88CS38B/CM38B/CP38B
Table 2.15.5.11 OSD Control Register List (2/2)
Register Bit Configuration
Bit4
Bit3
Bit2
Register
Address
Register
Name
Bit7
Bit6
Bit5
Bit1
Bit0
00FBB
ORIV
VDPOL
HDPOL
YBLII
RGBII
YIV
BLIV
RGBIV
IIV
00024
00025
0001D
ORDMA
DMA7
−
−
DMA6
−
SLNT
DMA5
−
EUL
DMA4
−
BLF
DMA3
−
IDT
DMA2
−
RDT
DMA1
−
GDT
DMA0
DMA8
BDT
0001E
0001F
00FBC
00FBD
00FBE
00FBF
00F80
ORCRA
CRA7
−
WVSH7
−
WVSL7
−
−
CRA6
−
WVSH6
−
WVSL6
−
−
CRA5
−
WVSH5
−
WVSL5
−
−
CRA4
−
WVSH4
−
WVSL4
−
−
CRA3
−
WVSH3
−
WVSL3
−
−
CRA2
−
WVSH2
−
WVSL2
−
RGWR
CRA1
−
WVSH1
−
WVSL1
−
EWDW
CRA0
CRA8
WVSH0
WVSH8
WVSL0
WVSL8
DON
ORDSN
ORWVSH
ORWVSl
ORDON
Bit Contents
VDPOL: VD input polarity select
HDPOL: HD input polarity select
YBLII: Y/BLIN input polarity select
RGBII: RIN, GIN, BIN input select
YIV: Y output polarity select
BLIV: BL output polarity select
RGBIV: R, G, B output polarity select
IIV: I pin polarity select
DMAx: Display memory address setting (x: 0 to 8)
SLNT: Slant
EUL: Underline
BLF: Blinking
IDT/RDT/CDT/BDT: Character color
CRAx: Character code (x: 0 to 8)
WVSHx: Window upper limit position (x: 0 to 8)
WVSL: Window lower limit position (x: 0 to 8)
RGWR: Writing data transfer control
EWDW: Window enable
DON: OSD display on/off
Note 1:
Except the meshed registers are changed by RGWR.
Note 2:
Only lower 2 bits of the register in address 00F80H are changed by RGWR (the register in address 00F80H
must not be used with any of the read-modify-write instructions as SET, CLR, etc.).
88CS38B-194
2007-09-12
TMP88CS38B/CM38B/CP38B
2.16 Jitter Elimination Circuit
The TMP88CS38B/CM38B/CP38B has a built-in jitter elimination circuit which maintains
the vertical stability of the OSD even when input of the vertical signal fluctuates.
And the field decision information for the OSD circuit is detected by using jitter elimination
circuit.
2.16.1
Configuration
Jitter removal status register
Phase detect signal PDF [2:0]
JRMSR
Field decision
circuit
HD (P70)
Previous field
decision
signal
A Y
B
S
VD (P71)
HD / VD
Edge detect circuit
Internal VD signal
output control
circuit
Delay value
setting circuit
A
B
Y
VD
(To OSD
circuit)
VDSEL
VD signal delay value
measuring circuit
fc/2
AFLD
JEEN
JECR
Jitter elimination control register
Figure 2.16.1 Jitter Elimination Circuit
88CS38B-195
2007-09-12
TMP88CS38B/CM38B/CP38B
2.16.2
Control
Jitter elimination circuit is controlled by the jitter elimination control register (JECR).
Jitter Elimination Control Register
JECR
7
6
5
4
3
2
1
0
(00FE4H)
−
−
−
VDSEL
AFLD
JEEN
“0”
“0”
VDSEL
0:
1:
0:
1:
0:
1:
VD select
AFLD
Automatic field decision
JEEN
Jitter elimination enable specification
VD from P71
VD from jitter elimination circuit
Automatic field decision disabled
Automatic field decision enabled
Jitter elimination disabled
Jitter elimination enabled
Note 1:
Clear the AFLD to “0” to disable jitter elimination circuit.
Note 2:
Always clear “0” to bit1 and bit0 of JECR.
Note 3:
(Initial value: ***0 0000)
Write
only
Clear “0” to AFLD and VDSEL if there is no phase shift in the vertical and horizontal sync. signals every
other time, such as with non-interlaced TV.
Note 4:
*: Don’t care
Note 5:
Setting JEEN to “0”, OSD display is only 2nd field.
Note 6:
Setting AFLD to “0”, OSD display is only 2nd field.
Jitter Elimination Status Register
JESR
(00FE5H)
7
6
5
4
3
2
1
0
FDSF
PDF1
PDF0
−
−
−
−
PDF2
(Initial value: 0*** ****)
0:
FDSF
Field detect status flag
PDF2 to
PDF0
Phase detect flag between HD and VD
A position of a scanning line exists in the field
which has a second display dot of character on an
interlace TV screen.
1: A position of a scanning line exists in the field
which has a first display dot of character on an
interlace TV screen.
Read
000: Phase 0
only
001: Phase 1
010: Phase 2
011: Phase 3
100: Phase 4
101: Phase 5
110: Phase 6
111: Phase 7
Note 1:
FDSF is different from the 1st and the 2nd field. It is a unique field decided for OSD display.
Note 2:
*: Don’t care.
Note 3:
HD
VD
Phase 7
Phase 0
Phase 1
Phase 2
Phase 3
Phase 4
Phase 5
Phase 6
Phase 7
Phase 0
Figure 2.16.2 Jitter Elimination Control Register and Jitter Elimination Status Register
2.16.3
Jitter Elimination Mode
The jitter elimination circuit is to identify the phase of the falling edges of the external
VD signal and HD signal. When VD signal is falling within HD signal falling +/−1/4HD,
the jitter is automatically eliminated and internal VD signal is set to the stable location.
This function is enabled by setting JEEN (Bit2 in JECR) in the jitter elimination control
register to “1”.
88CS38B-196
2007-09-12
TMP88CS38B/CM38B/CP38B
2.16.4
Auto Field Line Decision
The internal vertical and horizontal sync. signals corrected by the jitter elimination
circuit generate the field line decision signals used in the OSD.
The OSD display in normal mode
Type A)
When the OSD circuit is used on the TV system which has a phase shift in the
vertical and horizontal sync. Signals every other filed such as the interlace
TV, enable jitter elimination circuit and set “1” to AFLD and VDSEL. At this
time, the field lines which have first and second display dot of character are
displayed.
Type B)
When the OSD circuit is used on the TV system which has no phase shift in
the vertical and horizontal sync. Signals every other filed such as the
non-interlace TV, enable jitter elimination circuit and clear “0” to AFLD and
VDSEL. At this time, the field line which has a second display dot of
character is only displayed.
The OSD display in double scan mode
Type C)
Disable jitter elimination circuit and clear “0” to AFLD and VDSEL. At this
time, the field lines which have first and second display dot of character are
displayed.
(1) The field line which has a
first display dot of
character
(2) The field line which has a
second display dot of
character
Scanning System
Register
Display
Type A
VDSEL = 1, AFLD = 1
(1) and (2)
Type B
VDSEL = 0, AFLD = 0
(2)
Type C
VDSEL = 0, AFLD = 0
(1) and (2)
Figure 2.16.3 Relation with Field Line and VDSEL, AFLD
88CS38B-197
2007-09-12
TMP88CS38B/CM38B/CP38B
2.17 Data Slicer
The TMP88CS38B/CM38B/CP38B contains the data slicer to decode the caption data which
multiplied during vertical flyback time of the composite video signal.
The composite video signal inputs to the data slicer circuit through P32 (VIN1) and P33
(VIN0). The caption data is decoded from the video signal. The composite video signal including
negative sync-tip inputs to VIN0 and VIN1 pins. The data slicer can comply with the copy guard
signal and special signals, and receive accurately the caption data under the condition of a weak
electrical field or a ghost.
Note:
2.17.1
When the data slicer is used at fc = 16 MHz, set to “02H” in FC8CR.
When the data slicer is used at fc = 8 MHz, set to “00H” in FC8CR. (Refer to Figure 1.4.5)
Configuration
A0
A1
S
Z
SYNCINV
Slicer mode setting register 1
SIF status read register 2
(00FDFH)
C.Sync external input mode
SIFSMS1/SIFS1R
EXSYNC
C.Sync signal
Synchronous separator
VIN1
Sync-tip clamp
circuit
Comparator 1
H timing circuit
Composite
video
signal
V timing circuit
LINE21
VIN0
Pedestal clamp
circuit
INTSLI
(to interrupt)
Clamping pulse
Comparator 2
Slice level control
circuit
Sampling clock
generation
circuit
Data separator
DA converter
DACLCR
(00FD9H)
Sync-tip slice level
setting register
SIFSR
(00FDDH)
Slicer interface
circuit
DA converter
SLVLCR
(00FDAH)
Slice level
control register
SIFDR1
SIFDR2
(00FDBH)
(00FDCH)
Data register 1 Data register 2
Figure 2.17.1 Data Slicer
88CS38B-198
2007-09-12
TMP88CS38B/CM38B/CP38B
2.17.2
Functions
(1) Video signal input
A low pass filter, a voltage amplifier and a condenser of about 0.1 μF are connected
between the video signal and the video signal input pin of VIN1 and VIN0 pins, that is
shown as Figure 2.17.3 the low pass filter functions to reduce noise and color burst
from the video signal, passes the amplifier and inputs the video signal to both VIN1
and VIN0 pins.
(2) Synchronous separator
This circuit is to separate the synchronous signal from the video signal. When
DACL7 to DACL0 of DACLCR are set for the synchronous separation, the sync slice
level is capable of setting. DACL7 to DACL4 set the slice level at the rising edge of the
sync signal clamped data, and DACL3 to DACL0 set the slice level at the falling edge of
the sync-tip clamped data. (Refer to section 2.17.5)
(3) Data separator
The data separator replaces the caption data piled on the video signal with the
digital signal.
When SLVL5 to SLVL0 of SLVLCR are set to get the digital signal, the Initial value
of the caption data slice level is capable of setting. (Refer to section 2.17.5)
(4) Sync-tip clamp circuit
The sync-tip level is clamped to the specified value.
(5) Pedestal clamp circuit
The video signal is set to the specified voltage with the clamp pulse generated from
the H/V timing part, which is called as a pedestal clamp.
(6) DA converter
This converter gets the DA changed slice level of the clamp circuit to the comparator.
(7) Comparator
This comparator replaces the composite video signal with the digital value while
inputting to the comparator.
(8) H timing circuit
This circuit detects the horizontal synchronous signal from C.Sync signal separated
synchornously from the video signal, and generates the clamp pulse to clamp the video
signal and provides it to the pedestal clamp circuit. In addition, the circuit detects the
change of H frequency and provides the data to the sampling clock generation part.
(9) V timing circuit
This circuit detects the horizontal synchronous signal from C.Sync signal separated
synchornously from the video signal, and provides line 21 detection signal to take out
caption signal to the slice level control part.
(10) Slice level control circuit
This circuit detects CRI (Clock run in) signal from VIDEO signal with line 21
detection signal generated at H/V timing part after slicing, and controls to the most
suitable slice level and takes out the caption data.
88CS38B-199
2007-09-12
TMP88CS38B/CM38B/CP38B
(11) Sampling clock generation circuit
This circuit generates the sampling clock which is phase-locked to CRI signal with
CRI signal detected at the slice level control part. In addition, the circuit revises the
location where the sampling clock generates with H frequency variable data generated
at H timing generation part.
(12) Slicer interface circuit
This is a 16-bit serial interface to receive the serial data.
(13) Interrupt generation circuit
Interrupts are generated by a rise in the caption line detection signal.
Video signal
Caption line
7.7 μs
Caption line detection signal ( LINE21 )
95 μs
Interrupt generation
Figure 2.17.2 Interrupt Generation Timing
See the description of the on-screen display circuit interrupt vectors for details of
interrupt vectors.
(14) C.Sync external input mode
The external C.Sync signal can be used internally by setting EXSYNC (SIFSMS1
bit5) to “1“.
As shown in Figure 2.17.3 (b), insert a low-pass filter (fT = 503 kHz), voltage
amplifier
(× 2 voltage amplification), and a capacitor of approximately 0.1 μF between the video
signal and the video signal input pin VIN1 and input an external C.Sync signal to
CSIN.
The polarity of the C.Sync signal is selected by SYNCINV (SIFSMS1 bit6).
(Internally used as C.Sync .)
CSIN (P32)
SYNCINV
C.Sync (
)
“0”
C.Sync (
)
“1”
88CS38B-200
2007-09-12
TMP88CS38B/CM38B/CP38B
2.17.3
Video Signal Connection
TMP88CS38B/CM38B/CP38B
Outer circuit
0.1 μF
(1.0 VPP)
Composite
video signal
P32 (VIN1)
(2 VPP)
Low pass filter
Amplifier
P33 (VIN0)
0.1 μF
(a) Internal sync separation mode
TMP88CS38B/CM38B/CP38B
Outer circuit
(5.0 VPP)
Ext.C.Sync
signal
P32 (CSIN)
(1.0 VPP)
Composite
video signal
P33 (VIN0)
(2 VPP)
Low pass filter
0.1 μF
Amplifier
(b) C.sync external input mode
Figure 2.17.3 Video Signal Connection
Data Slicer Control Register
SINTCR
7
6
5
4
3
2
1
0
(00FD8H)
−
−
−
−
SLON
SLCR
−
−
SLON
Data slicer enable/disable
SLCR
Data slicer interrupt control
1:
0:
1:
0:
(Initial value: 0000 00**)
Enable
Disable
Enable interrupt
Disable interrupt
Write
only
Data Slicer Interrupt Satus Register
SINTCR
7
6
5
4
3
2
1
0
(00FD8H)
−
−
−
SLIS
−
−
−
−
SLIS
0:
1:
Data slicer interrupt status
−
Interrupt request
Note 1:
For setting SCLR to “1”, write “1” after SLON is set to “1”.
Note 2:
SLIS is cleared to “0” after reading SINTCR.
(Initial value: ***0 ****)
Read
only
Figure 2.17.4 Data Slicer Control (I)
88CS38B-201
2007-09-12
TMP88CS38B/CM38B/CP38B
SIF Data Register 1 (Caption data 1st byte read register) (Read only)
SIFDR1
(00FDBH)
7
6
5
4
3
2
1
0
D1ST7
D1ST6
D1ST5
D1ST4
D1ST3
D1ST2
D1ST1
D1ST0
D1ST7-0
Read
only
Caption data 1st byte read register
SIF Data Register 2 (Caption data 2nd byte read register) (Read only)
SIFDR2
(00FDCH)
7
6
5
4
3
2
1
0
D2ST7
D2ST6
D2ST5
D2ST4
D2ST3
D2ST2
D2ST1
D2ST0
D2ST7-0
Read
only
Caption data 2nd byte read register
SIF Status Register (Read only)
SIFST
(00FDDH)
7
6
5
4
3
2
1
0
STCRI
CRIN3
CRIN2
CRIN1
CRIN0
STFLD
STSB
STDE
STCRI
Clock run in detection
CRIN
CRI number − 1
1: Clock run in detection
0: No clock run in detection
Actual CRI number − 1
1: 2nd field
0: 1st field
1: From detection of start bit until fall in VD
0: Other times
STFLD
Field identification
STSB
Start bit identification flag
STDE
16-bit data receive end identification
flag
1:
0:
Read
only
From end of 16-bit data reception until fall in VD
Other times
Figure 2.17.5 Data Slicer Control (II)
Slicer Mode Setting Register 1 (Write only)
SIFSMS1
(00FDFH)
7
6
5
SYNC
INV EXSYNC
“0”
4
“1”
3
CLINE
Note:
1
0
CLINE3 CLINE2 CLINE1 CLINE0
SYNCINV Sync signal input inversion
EXSYNC
2
Sync signal selection
Setting lines piled on caption data
(Initial value: 0001 1011)
0:
No inversion
1:
Inversion of C.Sync external input signal
0:
Internal sync separation
1:
External C.Sync input
0000: 10 lines
0001: 11 lines
0010: 12 lines
0011: 13 lines
0100: 14 lines
0101: 15 lines
0110: 16 lines
0111: 17 lines
1000: 18 lines
1001: 19 lines
1010: 20 lines
1011: 21 lines
1100: 22 lines
1101: 23 lines
1110: 24 lines
1111: 25 lines
Write
only
Always write “0” to bit7 of SIFSMS1 and “1” to bit4 when writing to SIFSMS1.
Figure 2.17.6 Data Slicer Control (III)
88CS38B-202
2007-09-12
TMP88CS38B/CM38B/CP38B
SIF Status Read Register 2
SIFS1R
7
6
(00FDFH)
−
−
GOODV
FLINE
5
4
3
2
1
0
GOODV FLINE4 FLINE3 FLINE2 FLINE1 FLINE0
Monitor signal of synchronization
Field scanning line
(Standard 262.5 = − 1)
Two’s complement
0:
1:
00000:
00001:
00010:
00011:
00100:
00101:
00110:
00111:
01000:
01001:
01010:
01011:
01100:
01101:
01110:
01111:
10000:
10001:
10010:
10011:
10100:
10101:
10110:
10111:
11000:
11001:
11010:
11011:
11100:
11101:
11110:
11111:
Out of synchronization (One or more)
V timing synchronizing
0
263.5
1
264.5
2
3
4
5
6
7
8
9
10
11
12
13
14
15
278.5
V synchronizing adjustment
− 15
248.5
− 14
− 13
− 12
− 11
− 10
−9
−8
−7
−6
−5
−4
−3
−2
261.5
−1
262.5
Read
only
Figure 2.17.7 Data Slicer Control (IV)
The explanation of the monitor signals (GOODV, FLINE) are as follows.
1.GOODV 0: Data slicer can not synchronize video signal.
1: Data slicer can synchronize video signal.
2.FLINE The number of field signal scanning line which the data slicer is detecting or
monitor flag of detecting state.
Example: FLINE = 1FH: NTSC signal
FLINE = 10H: V synchronizing adjustment
88CS38B-203
2007-09-12
TMP88CS38B/CM38B/CP38B
Caption Data Slice Level Control Register (Write/Read)
SLVLCR
7
6
5
4
3
2
1
0
(00FDAH)
−
−
SLVL5
SLVL4
SLVL3
SLVL2
SLVL1
SLVL0
(Initial value: **00 1010)
000000: VPCLAMP + (1/256) VDD
000001: VPCLAMP + (2/256) VDD
000010: VPCLAMP + (3/256) VDD
SLVL
000011: VPCLAMP + (4/256) VDD
Slice level (Initial value:) setting
Sice level setting
000100: VPCLAMP + (5/256) VDD
.
.
.
.
.
.
111101: VPCLAMP + (62/256) VDD
Write
111110: VPCLAMP + (63/256) VDD
111111: VPCLAMP + (64/256) VDD
SLVL
Slice level (final value)
Read
Note 1:
VPCLAMP (Pedestal clamp) = (1/2) VDD
Note 2:
The SLVLCR has different write buffer and read buffer, and cannot be read write-buffer fata. The SBIDBR
cannot be used with any read-modify-write instructions. (Bit manipulation instructions such as SET, CLR,
etc. and logical operation such as AND, OR, etc.)
Sync-tip Slice Level Setting Register (Write only)
DACLCR
7
6
5
4
3
2
1
0
(00FD9H)
DACL7
DACL6
DACL5
DACL4
DACL3
DACL2
DACL1
DACL0
(Initial value: 0100 0010)
0000: VSCLAMP + (3/512) VDD
0001: VSCLAMP + (6/512) VDD
DACL
DACL7 to DACL4: Slice level
Lower limit setting
DACL3 to DACL0: Slice level
Upper limit setting
0010: VSCLAMP + (9/512) VDD
0011: VSCLAMP + (12/512) VDD
.
.
.
.
.
.
1101: VSCLAMP + (42/512) VDD
Write
only
1110: VSCLAMP + (45/512) VDD
1111: VSCLAMP + (48/512) VDD
Note:
VSCLAMP (Sync-tip clamp) = (204/512) VDD
Figure 2.17.8 Data Slicer Control (V)
88CS38B-204
2007-09-12
TMP88CS38B/CM38B/CP38B
2.17.4
Clamp and Data Slicer Operation
The slicer uses the following steps to obtain the caption signals:
Sync signal separation
The composite video signal input via VIN1 (Pin 40) is clamped by the sync tip
clamp circuit and the HD and VD sync signals separated by the sync separation
circuit.
Caption line detection
Field decision and caption line detection are effected using the HD and VD sync
signals
CRI detection
The CRI signal of the caption line interval is detected from the pedestal clamped
video signal at VIN0 (Pin 41).
Slice level setting and
generation of sampling clock
The slice level is controlled during the CRI signal interval, detected by the slice
level control block, to obtain the optimum level.
To determine the timing for extracting the caption data, a sampling clock is
generated that is phase locked to the CRI.
Caption signal extraction
The caption data is extracted at the selected slice level using sampling clock,
which is locked to the caption data.
The data slicer has two separation circuits:
a. Sync signal (sync tip clamp + sync signal slice) separation.
b. Caption data (pedestal clamp + data slice) separation.
The two circuits are described briefly below.
88CS38B-205
2007-09-12
TMP88CS38B/CM38B/CP38B
a.
Sync signal (Sync tip clamp + sync signal slice)
a-1 Sync tip clamp (Pin 40) ........The sync tip is clamped at (204/512) VDD [V] as shown
in Figure 2.17.9.
Video signal
1
A, B: Sync tip slice levels
A: DACL7 to DACL4
Lower-limit setting
B: DACL3 to DACL0
Upper-limit setting
2
B
A
(204/512) VDD [V]
GND
After sync signal separation
H
L
Figure 2.17.9 Sync Signal Slice
a-2 Method of sync signal slice
The sync signal is separated as shown in Figure 2.17.9.
Sync signal separation is accomplished by comparing the voltage of the sync
tip-clamped video signal with the sync tip slice level. For a 1 → 2 video signal
change, if the sync signal after separation is high, the slice level A is selected; if
low, the slice level B is selected.
(Sync tip slice level)
Slice level = VSCLAMP + {(3 + 3X)/512} VDD
VDD: Power supply voltage
VSCLAMP: Sync tip clamp voltage = (204/512) VDD
X: Setup data (4 bits)
88CS38B-206
2007-09-12
TMP88CS38B/CM38B/CP38B
b.
Caption data (Pedestal clamp + data slice)
b-1 Pedestal clamp (Pin 41) ......Clamped at (1/2) VDD [V] as shown in Figure 2.17.10.
Slice level
(1/2) VDD [V]
GND
Figure 2.17.10 Pedestal Clamp
b-2 Method of data slice
The data slice level constitutes a level at which the CCD data is differentiated.
The slice level’s setup value is indicated by the following:
Slice level = VPCLAMP + (X/256) VDD [V]
VDD: Power supply voltage
VPCLAMP: Pedestal clamp voltage = (1/2) VDD
X: Setup data (6 bits)
b-3 Automatic slice level correction circuit
The slice level is corrected to the appropriate value during the CRI period.
Slice level correction always begins with the setup value of SLVL (Bit5 to bit0 of
SLVLCR).
If you want the last value to become the initial value of the next slice level, set it
to SLVL (Bit5 to bit0 of SLVLCR).
88CS38B-207
2007-09-12
TMP88CS38B/CM38B/CP38B
Input/Output Circuit
(1) Control pins
The input/output circuitries of the TMP88CS38B/CM38B/CP38B control pins are shown
below.
Control Pin
I/O
Input/Output Circuitry
Osc. enable
XIN
XOUT
Remarks
Resonator connection pins
(High frequency)
fc
VDD
VDD
Rf
I/O
Rf = 1.2 MΩ (typ.)
RO
XIN
RO = 0.5 kΩ (typ.)
XOUT
Sink open-drain output
Hysteresis input
Pull-up resistor
VDD
RIN
R
RESET
I/O
Address-trap-reset
Watchdog-timer-reset
System-clock-reset
RIN = 220 kΩ (typ.)
R = 1 kΩ (typ.)
Hysteresis input
VDD
R = 1 kΩ (typ.)
STOP / INT5
(P20)
Input
R
P20/ STOP / INT5
Pull-down resistor
VDD
RIN = 70 MΩ (typ.)
R
TEST
R = 1 kΩ (typ.)
Input
RIN
Osc. enable
OSC1
OSC2
fc
VDD
Rf
I/O
OSC1
RO
VDD
Pin for connecting a resonator
for on-screen display
Rf = 1.2 MΩ (typ.)
RO = 0.5 kΩ (typ.)
OSC2
88CS38B-208
2007-09-12
TMP88CS38B/CM38B/CP38B
(2) Input/output ports
Port
I/O
Input/Output Circuitry
VDD
Initial “High-Z”
P20
Remarks
Sink open-drain output
Hysteresis input
R = 1 kΩ (typ.)
I/O
R
P30
to
P33
P50,
P57
Tri-state I/O
Hysteresis input
VDD
Initial “High-Z”
I/O
R = 1 kΩ (typ.)
R
Disable
P70,
P71
P34,
P35,
P51,
P52
Open drain
output enable
I/O
R
Disable
R = 1 kΩ (typ.)
P40
I/O
R
Disable
P47
P53
Tri-state I/O
Hysteresis input
Key-on wakeup input
(VIL4 = 0.65 × VDD)
VDD
Initial “High-Z”
to
R = 1 kΩ (typ.)
Tri-state I/O
VDD
Initial “High-Z”
to
Tri-state I/O or open-drain
output programmable
Hysteresis input
VDD
Initial “High-Z”
R
Disable
I/O
R = 1 kΩ (typ.)
RA = 5 kΩ (typ.)
P56
CA = 22 pF (typ.)
CA
RA
Key-on
wakeup
88CS38B-209
2007-09-12
TMP88CS38B/CM38B/CP38B
Port
I/O
Input/Output Circuitry
Remarks
Sink open-drain output
High current output
IOL = 20 mA (typ.)
VDD
Initial “High-Z”
P60,
P61
I/O
R
Disable
RA = 5 kΩ (typ.)
CA = 22 pF (typ.)
CA
Initial “High-Z”
P62
(at
CSOUT)
RA
Key-on
wakeup
Key-on wakeup input
(VIL4 = 0.65 × VDD)
Tri-state I/O
High current output
IOL = 20 mA (typ.)
VDD
I/O
R
Disable
I/O
R
Disable
Initial “High-Z”
P67
R = 1 kΩ (typ.)
Tri-state I/O
VDD
R = 1 kΩ (typ.)
P64
to
R = 1 kΩ (typ.)
Sink open-drain output
High current output
IOL = 20 mA (typ.)
VDD
Initial “High-Z”
P62,
P63
R = 1 kΩ (typ.)
I/O
R
Disable
88CS38B-210
2007-09-12
TMP88CS38B/CM38B/CP38B
Electrical Characteristics
(VSS = 0 V)
Absolute Maximum Ratings
Parameter
Symbol
Pins
Supply voltage
VDD
−
−0.3 to 6.5
Input voltage
VIN
−
−0.3 to VDD + 0.3
Output voltage
VOUT1
−
−0.3 to VDD + 0.3
Output current (Per 1 pin)
Output current (Total)
Ratings
IOUT1
Ports P2, P3, P4, P5, P64 to P67, P7
IOUT2
Ports P60 to P63
Unit
V
3.2
30
mA
Σ IOUT1
Ports P2, P3, P4, P5, P64 to P67, P7
Σ IOUT2
Ports P60 to P63
120
120
TMP88CS38: 600
TMP88CP38A/CM38A: 400
Power dissipation [Topr = 70°C]
PD
−
Soldering temperature (Time)
Tsld
−
Storage temperature
Tstg
−
−55 to 125
Operating temperature
Topr
−
−30 to 70
mW
260 (10 s)
°C
Note: The absolute maximum ratings are rated values which must not be exceeded during operation,
even for an instant. Any one of the ratings must not be exceeded. If any absolute maximum rating is
exceeded, a device may break down or its performance may be degraded, causing it to catch fire or
explode resulting in injury to the user. Thus, when designing products which include this device,
ensure that no absolute maximum rating value will ever be exceeded.
(VSS = 0 V, Topr = −30 to 70°C)
Recommended Operating Conditions
Parameter
Symbol
Pins
Conditions
Min
Max
4.5
5.5
Unit
Fc = 16 MHz NORMAL mode
Supply voltage
Fc = 16 MHz IDLE mode
VDD
STOP mode
Input high voltage
Input low voltage
Clock frequency
VIH1
Except hysteresis input
VIH2
Hysteresis input
VIL1
Except hysteresis input
VIL2
Hysteresis input
VIL4
Key-on wakeup input
VDD = 4.5 to 5.5V
XIN, XOUT
VDD = 4.5 to 5.5V
OSC1, OSC2
VDD × 0.75
VDD = 4.5 to 5.5V
VDD
V
VDD × 0.30
VDD = 4.5 to 5.5V
fc
fOSC
VDD × 0.70
VDD = 4.5 to 5.5V
0
VDD × 0.25
VDD × 0.65
8.0
16.0
fc = 8 MHz
8.0
12.0
fc = 16 MHz
16.0
24.0
MHz
Note 1: The recommended operating conditions for a device are operating conditions under which it can be
guaranteed that the device will operate as specified. If the device is used under operating conditions
other than the recommended operating conditions (Supply voltage, operating temperature range,
specified AC/DC values etc.), malfunction may occur. Thus, when designing products which include
this device, ensure that the recommended operating conditions for the device are always adhered
to.
Note 2: Clock frequency fc: Supply voltage range is specified in NORMAL mode and IDLE mode.
Note 3: Smaller value is alternatively specified as the maximum value.
88CS38B-211
2007-09-12
TMP88CS38B/CM38B/CP38B
(VSS = 0 V, Topr = −30 to 70°C)
DC Characteristics
Parameter
Symbol
Hysteresis voltage
Input current
Pins
Conditions
Typ.
Max
Unit
−
0.9
−
V
VHS
Hysteresis inputs
IIN1
TEST
VDD = 5.5 V, VIN = 5.5 V/0 V
−
−
±2
IIN2
Open-drain ports
VDD = 5.5 V, VIN = 5.5 V/0 V
−
−
±2
IIN3
Tri-state ports
VDD = 5.5 V, VIN = 5.5 V/0 V
−
−
±2
IIN4
RESET , STOP
VDD = 5.5 V, VIN = 5.5 V/0 V
Input resistance
RIN2
RESET
VDD = 5.5 V, VIN = 0 V
Output leakage
current
ILO1
Sink open-drain ports
ILO2
Output high voltage
VOH2
Output low voltage
Output low current
−
−
±2
100
220
450
VDD = 5.5 V, VOUT = 5.5 V
−
−
2
Tri-state ports
VDD = 5.5 V, VOUT = 5.5 V/0 V
−
−
±2
Tri-state ports
VDD = 4.5 V, IOH = − 0.7 mA
4.1
−
−
VOL
Except XOUT, OSC2 and
ports P60 to P63
VDD = 4.5 V, IOL = 1.6 mA
−
−
0.4
IOL3
Port P60 to P63
VDD = 4.5 V, VOL = 1.0 V
−
20
−
VDD = 5.5 V
fc = 16 MHz
VIN = 5.3 V/0.2 V
−
25
30
−
20
25
−
0.5
10
Supply current in
NORMAL mode
Supply current in
IDLE mode
Min
−
IDD
kΩ
μA
V
(Note 3)
VDD = 5.5 V
VIN = 5.3 V/0.2 V
Supply current in
STOP mode
μA
mA
μA
Note 1: Typical values show those at Topr = 25°C, VDD = 5 V.
Note 2: Input current IIN3: The current through resistor is not included.
Note 3: Supply current IDD: The current (Typ. 0.5 mA) through ladder resistors of ADC is included in
NORMAL mode and IDLE mode.
AD Conversion Characteristics
Parameter
Symbol
(VSS = 0 V, VDD = 4.5 V to 5.5 V, Topr = −30 to 70°C)
Conditions
Min
Typ.
Max
VAREF
supplied from VDD pin.
−
VDD
−
VASS
supplied from VSS pin.
−
0
−
= VDD − VSS
−
VDD
−
VSS
−
VDD
−
−
±1
−
−
±2
Full scale error
−
−
±2
Total error
−
−
±3
Analog reference voltage
Analog reference voltage range
Analog input voltage
ΔVAREF
VAIN
Nonlinearity error
Zero point error
VDD = 5.0 V
Unit
V
LSB
Note: The total error means all error except quanting error.
88CS38B-212
2007-09-12
TMP88CS38B/CM38B/CP38B
(VSS = 0 V, VDD = 4.5 V to 5.5 V, Topr = −30 to 70°C)
AC Characteristics
Parameter
Symbol
Conditions
Min
Typ.
Max
Unit
0.5
−
1.0
μs
31.25
−
−
ns
in NORMAL mode
Machine cycle time
tcy
in IDLE mode
High level clock pulse width
TWCH
for external clock operation
Low level clock pulse width
TWCL
(XIN input), fc = 16 MHz
Recommended Oscillating Conditions
Parameter
High-frequency
oscillation
Oscillator
Ceramic resonator
(VSS = 0 V, VDD = 4.5 V to 5.5 V, Topr = −30 to 70°C)
Oscillation
Frequency
Recommended Oscillator
Recommended
Constant
C1
C2
8 MHz
Murata
CSA 8.00MTZ
30 pF
30 pF
16 MHz
Murata
CSA 16.00MXZ040
5 pF
5 pF
XIN
XOUT
C1
C2
High-frequency oscillation
Note 1: To keep reliable operation, shield the device electrically with the metal plate on its package mold
surface against the high electric field, for example, by CRT (Cathode ray tube).
Note 2: The product numbers and specifications of the resonators by Murata Manufacturing Co., Ltd. are
subject to change. For up-to-date information, please refer to the following URL:
http://www.murata.co.jp/search/index.html
88CS38B-213
2007-09-12
TMP88CS38B/CM38B/CP38B
Recommended Oscillating Conditions
Item
(VSS = 0 V, VDD = 4.5 V to 5.5 V, Topr = −30 to 70°C)
Oscillation for OSD
Recommended Parameter Value
Oscillation
Resonator
Frequency
L (μH)
C1 (pF)
C2 (pF)
8 MHz
33
5 to 30
10
12 MHz
15
5 to 30
10
16 MHz
10
5 to 30
10
20 MHz
6.8
5 to 25
10
24 MHz
4.7
5 to 25
10
LC resonator
OSC1
OSC2
L
C2
C1
Oscillation for OSD
The frequency generated in LC oscillation can be obtained using the following equations.
f=
1
2π LC
,C =
C1・C2
C1 + C2
C1 is not fixed at a constant value. It can be changed to tune into the desired frequency.
Note 1: Toshiba’s OSD circuit determines a horizontal display start position by counting clock pulses
generated in LC oscillation. For this reason, the OSD circuit may fail to detect clock pulses normally,
resulting in the horizontal start position becoming unstable, at the beginning of oscillation, if the
oscillation amplitude is low.
Changing L and C2 from the values recommended for a specific frequency may hamper a stable
OSD display.
If the LC oscillation frequency is the same as a high-frequency clock value, the oscillation of the
high-frequency oscillator may cause the LC oscillation frequency to fluctuate, thus making OSD
displays flicker.
When determining these parameters, please check the oscillation frequency and the stability of
oscillation on your TV sets.
Also check the determined parameters on your final products, because the optimum parameter
values may vary from one product to another.
Note 2: When using the LSI package in a strong electric field, such as near a CRT, electrically shield the
package so that its normal operation can be maintained.
88CS38B-214
2007-09-12
TMP88CS38B/CM38B/CP38B
Notice of ROM Entry
When you make a ROM data entry for TMP88CS38B and TMP88CM38B/CP38B,
Please transfer one file including program area, vector table area and OSD font area.
The ROM area must be transferred is as follows.
TMP88CS38B
4000H
TMP88CM38B
TMP88CP38B
4000H
4000H
Program area
Program area
Program area
BEFFH
FEFFH
13EFFH
20000H
20000H
20000H
OSD font area
OSD font area
OSD font area
25FFFH
25FFFH
25FFFH
FFF00H
FFF00H
FFF00H
Vector table
area
Vector table
area
Vector table
area
FFFFFH
FFFFFH
FFFFFH
Flow of ROM data entry
After evaluation finished
Program and vector table
OSD font
Program
vector table
OSD font
Two files are merged into one file.
ROM data entry
88CS38B-215
2007-09-12
TMP88CS38B/CM38B/CP38B
Package
P-SDIP42-600-1.78
Unit: mm
88CS38B-216
2007-09-12
TMP88CS38B/CM38B/CP38B
P-QFP44-1414-0.80K
Unit: mm
88CS38B-217
2007-09-12
TMP88CS38B/CM38B/CP38B
88CS38B-218
2007-09-12