MP4211 TOSHIBA Power MOS FET Module Silicon P Channel MOS Type (Four L2-π-MOSV inOne) MP4211 Industrial Applications High Power, High Speed Switching Applications For Printer Head Pin Driver and Pulse Motor Driver For Solenoid Driver • 4-V gate drivability • Small package by full molding (SIP 10 pin) • High drain power dissipation (4 devices operation) : PT = 4 W (Ta = 25°C) Unit: mm • Low drain-source ON resistance: RDS (ON) = 0.16 Ω (typ.) • High forward transfer admittance: |Yfs| = 4.0 S (typ.) • Low leakage current: IGSS = ±10 μA (max) (VGS = ±16 V) IDSS = −100 μA (max) (VDS = −60 V) • Enhancement-mode: Vth = −0.8 to −2.0 V (VDS = −10 V, ID = −1 mA) Absolute Maximum Ratings (Ta = 25°C) Characteristics Symbol Rating Unit Drain-source voltage VDSS −60 V Drain-gate voltage (RGS = 20 kΩ) VDGR −60 V Gate-source voltage VGSS ±20 V DC ID −5 Pulse IDP −20 Drain power dissipation (1-device operation, Ta = 25°C) PD 2.0 W Drain power dissipation (- device operation, Ta = 25°C) PDT 4.0 W Single pulse avalanche energy (Note 1) EAS 273 mJ Avalanche current IAR −5 A EAR 0.2 EART 0.4 Channel temperature Tch 150 °C Storage temperature range Tstg −55 to 150 °C Drain current 1-device operation Repetitive avalanche energy (Note 2) 4-device operation A JEDEC ― JEITA ― TOSHIBA 2-25A1C Weight: 2.1 g (typ.) mJ Note 1: Condition for avalanche energy (single pulse) measurement VDD = −25 V, starting Tch = 25°C, L = 14.84 mH, RG = 25 Ω, IAR = −5 A Note 2: Repetitive rating; pulse width limited by maximum channel temperature Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). This transistor is an electrostatic-sensitive device. Please handle with caution. 1 2006-10-27 MP4211 Array Configuration 1 2 4 3 5 6 10 8 7 9 Thermal Characteristics Characteristics Thermal resistance from channel to ambient Symbol Max Unit ΣRth (ch-a) 31.2 °C/W TL 260 °C (4-device operation, Ta = 25°C) Maximum lead temperature for soldering purposes (3.2 mm from case for t = 10 s) Electrical Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Gate leakage current IGSS VGS = ±16 V, VDS = 0 V ― ― ±10 μA Drain cut-off current IDSS VDS = −60 V, VGS = 0 V ― ― −100 μA V (BR) DSS ID = −10 mA, VGS = 0 V −60 ― ― V Vth VDS = −10 V, ID = −1 mA −0.8 ― −2.0 V VGS = −4 V, ID = −2.5 A ― 0.24 0.28 VGS = −10 V, ID = −2.5 A ― 0.16 0.19 VDS = −10 V, ID = −2.5 A 2.0 4.0 ― S ― 630 ― pF ― 95 ― pF ― 290 ― pF ― 25 ― ― 45 ― Gate threshold voltage Drain-source ON resistance RDS (ON) Forward transfer admittance |Yfs| Input capacitance Ciss Reverse transfer capacitance Crss Output capacitance Coss Rise time VDS = −10 V, VGS = 0 V, f = 1 MHz tr ID = −2.5 A 0V Turn-on time ton VGS −10 V Fall time Turn-off time Total gate charge (Gate-source plus gate-drain) 4.7 Ω Switching time tf toff Qgs Gate-drain (“miller”) charge Qgd ns ― 55 ― ― 200 ― ― 22 ― nC ― 16 ― nC ― 6 ― nC VDD ≈ −30 V VIN: tr, tf < 5 ns, duty ≤ 1%, tw = 10 μs Qg Gate-source charge Ω VOUT RL = 12 Ω Drain-source breakdown voltage VDD ≈ −48 V, VGS = −10 V, ID = −5 A 2 2006-10-27 MP4211 Source-Drain Diode Ratings and Characteristics (Ta = 25°C) Characteristics Symbol Test Condition Min Typ. Max Unit Continuous drain reverse current IDR ― ― ― −5 A Pulse drain reverse current IDRP ― ― ― −20 A Diode forward voltage VDSF IDR = −5 A, VGS = 0 V ― ― 1.7 V Reverse recovery time trr IDR = −5 A, VGS = 0 V ― 80 ― ns Reverse recovery charge Qrr dIDR/dt = 50 A/μs ― 0.1 ― μC Marking MP4211 JAPAN Part No. (or abbreviation code) Lot No. A line indicates lead (Pb)-free package or lead (Pb)-free finish. 3 2006-10-27 MP4211 ID – VDS ID – VDS −5 −10 Common source −6 Tc = 25°C −6 Common source Tc = 25°C −8 −4 −4 −8 −8 −10 Drain current ID (A) Drain current ID (A) −10 −3.5 −4 −3 −3 −2 −6 −3.5 −4 −3 −2.5 −1 −2 −2.5 VGS = −2 V 0 0 −0.4 −0.8 −1.2 Drain-source voltage −1.6 VGS = −2 V 0 0 −2.0 −2 VDS (V) −4 −8 Drain-source voltage ID – VGS −10 VDS (V) VDS – VGS −2.0 −10 Common source 100 Common source VDS = −10 V VDS (V) Tc = −55°C 25 −8 −6 −4 −2 Tc = 25°C −1.6 −1.2 Drain-source voltage Drain current ID (A) −6 −0.8 ID = −5 A −4 −3 −0.4 −2 ) −1 0 0 −2 −4 −6 Gate-source voltage −8 0 0 −10 −4 −8 VGS (V) −16 −20 VGS (V) RDS (ON) – ID 30 3 Common source Common source VDS = −10 V Drain-source ON resistance RDS (ON) (Ω) |Yfs| (S) |Yfs| – ID Forward transfer admittance −12 Gate-source voltage 10 5 Tc = −55°C 3 25 100 1 Tc = 25°C 1 0.5 0.3 −10 0.1 0.5 0.05 0.3 −0.1 0.03 −0.1 −0.3 −1 −3 −10 −30 Drain current ID (A) VGS = −4 V −0.3 −1 −3 −10 −30 Drain current ID (A) 4 2006-10-27 MP4211 IDR – VDS −30 Common source (A) Common source 0.8 Drain reverse current IDR Drain-source ON resistance RDS (ON) (Ω) RDS (ON) – Tc 1.0 0.6 ID = −5 A 0.4 −2.5 −1.2 VGS = −4 V 0.2 ID = −5, −2.5, −1.2 A VGS = −10 V 0 −80 −40 0 40 80 120 Tc = 25°C −10 −5 −3 −10 −3 −1 −0.5 −1 −0.1 0 160 VGS = 0, 1 V −0.3 0.4 Case temperature Tc (°C) 0.8 1.2 Drain-source voltage Capacitance – VDS 1.6 2.0 VDS (V) Vth – Tc 10000 −2.0 Vth (V) 5000 1000 Gate threshold voltage Capacitance C (pF) 3000 Ciss 500 300 Coss Common source 100 VGS = 0 V 50 Crss f = 1 MHz Tc = 25°C 30 −0.1 −0.3 −1 −3 −10 Drain-source voltage −30 −1.6 −1.2 −0.8 Common source −0.4 VDS = −10 V ID = −1 mA −100 0 −80 VDS (V) −40 0 40 80 120 160 Case temperature Tc (°C) Dynamic Input/Output Characteristics −16 VDS −30 −12 −24 −20 −10 0 0 VDD = −48 V −8 −4 VGS 8 −12 16 24 32 −30 IDP max 100 μs* −10 Drain current ID (A) −40 Safe Operating Area −20 VGS (V) Common source ID = −5 A Tc = 25°C Gate-source voltage Drain-source voltage VDS (V) −50 10 ms* 100 ms* *: Single nonrepetitive pulse Tc = 25°C Curves must be derated linearly with increase in temperature. −0.1 −1 Total gate charge Qg (nC) 1 ms* −1 −0.3 0 40 ID max −3 −3 −10 −30 Drain-source voltage 5 −100 −300 VDS (V) 2006-10-27 MP4211 Transient thermal resistance rth (°C/W) rth – tw 300 100 30 Curves should be applied in thermal limited area. (Single nonrepetitive pulse) The figure shows thermal resistance per device versus pulse width. (1) (2) 10 -No heat sink/Attached on a circuit board(1) 1-device operation (2) 2-device operation (3) 3-device operation Circuit board (4) 4-device operation 3 1 0.5 0.001 0.01 0.1 1 Pulse width 10 100 EAS – Tch Avalanche energy EAS (mJ) (W) PDT Total power dissipation 500 (1) 1-device operation (2) 2-device operation (3) 3-device operation (4) 4-device operation Attached on a circuit board 6 (4) Circuit board (3) (2) 2 (1) 0 0 40 80 1000 tw (s) PDT – Ta 8 4 (4) (3) 120 160 400 300 200 100 0 25 200 50 Ambient temperature Ta (°C) 75 100 125 Channel temperature Tch 150 (°C) ΔTch – PDT Channel temperature increase ΔTch (°C) 160 (1) (2) (3) (4) 120 15 V 80 IAR −15 V VDD Circuit board Attached on a circuit board 40 0 0 BVDSS (1) 1-device operation (2) 2-device operation (3) 3-device operation (4) 4-device operation 1 2 3 Total power dissipation 4 PDT TEST CIRCUIT Peak IAR = −5 A, RG = 25 Ω VDD = −25 V, L = 14.84 mH 5 VDS TEST WAVE FORM ⎞ 1 2 ⎛ B VDSS ⎟ Ε AS = ·L·I · ⎜⎜ ⎟ 2 V − DD ⎠ ⎝ B VDSS (W) 6 2006-10-27 MP4211 RESTRICTIONS ON PRODUCT USE 20070701-EN • The information contained herein is subject to change without notice. • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 7 2006-10-27