TSV911-TSV912-TSV914 Rail-to-rail input/output 8MHz operational amplifiers Features ■ Rail-to-rail input and output ■ Wide bandwidth ■ Low power consumption: 1.1mA max. ■ Unity gain stability ■ High output current: 35mA ■ Operating from 2.5V to 5.5V ■ Low input bias current ■ ESD Internal protection≥ 5kV ■ Latch-up immunity Pin connections (top view) SOT23-5 Signal conditioning ● Active filtering ● Medical instrumentation August 2006 . 3 VCC 4 Inverting Input 1 2 _ Non Inverting Input 3 + VDD 4 Output 1 1 Inverting Input 1 2 _ Non Inverting Input 1 3 + VDD 8 N.C. 7 VCC 6 Output 5 N.C. _ + 4 8 VCC 7 Output 2 6 Inverting Input 2 5 Non Inverting Input 2 SO-14, TSSOP14 Applications ● Non Inverting Input 5 MiniSO-8, SO-8 (dual) These characteristics make the TSV911/2/4 family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. Portable devices 2 Inverting Input This family features an excellent speed/power consumption ratio, offering an 8MHz gainbandwidth product while consuming only 1.1mA max at 5V supply voltage. These op-amps are unity gain stable for capacitive loads up to 200pF. They also feature an ultra-low input bias current. ● VDD N.C. The TSV911/2/4 family of single, dual & quad operational amplifiers offers low voltage operation and rail-to-rail input and output. Battery-powered applications 1 SO-8 (single) Description ● Output Rev.1 Output 1 1 Inverting Input 1 2 _ _ 14 Output 4 13 Inverting Input 4 Non Inverting Input 1 3 + + 12 Non Inverting Input 4 VCC 4 Non Inverting Input 2 5 Inverting Input 2 6 Output 2 7 11 VDD + _ + _ 10 Non Inverting Input 3 9 Inverting Input 3 8 Output 3 1/18 www.st.com 18 Contents TSV911-TSV912-TSV914 Contents 1 Device summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings & operating conditions . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 2/18 4.1 SOT23-5 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2 MiniSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.3 SO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.4 TSSOP14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.5 SO-14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 TSV911-TSV912-TSV914 1 Device summary table Device summary table Part number Temperature range Package Packing TSV911ID TSV911IDT Marking V911I SO-8 Tube or tape & reel TSV911AID TSV911AIDT V911AI TSV911ILT K127 SOT23-5 TSV911AILT Tape & reel TSV912IST K125 MiniSO-8 TSV912AIST TSV912ID TSV912IDT V912I SO-8 Tube or tape & reel TSV912AID TSV912AIDT V912AI TSV914IPT V914I TSSOP14 Tape & reel TSV914AIPT TSV914ID TSV914IDT V914AI -40 - 125°C V914I SO-14 TSV914AID TSV914AIDT V914AI TSV911IYD TSV911IYDT V911IY TSV911AIYD TSV911AIYDT V911AY SO-8 Tube or tape & reel TSV912IYD TSV912IYDT V912IY TSV912AIYD TSV912AIYDT V912AY TSV914IYD TSV914IYDT V914IY SO-14 TSV914AIYD TSV914AIYDT V914AY 3/18 Absolute maximum ratings & operating conditions 2 TSV911-TSV912-TSV914 Absolute maximum ratings & operating conditions Table 1. Absolute maximum ratings (AMR) Symbol VCC Vid Parameter Supply voltage(1) Differential input voltage (2) (3) Vin Input voltage Tstg Storage temperature Thermal resistance junction to ambient Rthja (4) (5) Tj 6 V ±VCC V VDD-0.2 to VCC+0.2 V -65 to +150 °C 250 SO-8 125 MiniSO-8 190 SO-14 103 TSSOP14 100 81 SO-8 40 MiniSO8 39 SO14 31 TSSOP14 32 Maximum junction temperature MM: machine model(6) model(7) CDM: charged device model(8) Latch-up immunity °C/W - SOT23-5 HBM: human body ESD Unit SOT23-5 Thermal resistance junction to case Rthjc Value °C/W 150 °C 5 kV 300 V 1.5 kV 200 mA 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. Vcc-Vin must not exceed 6V. 4. Short-circuits can cause excessive heating and destructive dissipation. 5. Rth are typical values. 6. Human body model: 100pF discharged through a 1.5kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 7. Machine model: a 200pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5Ω), done for all couples of pin combinations with other pins floating. 8. Charge device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. Table 2. Operating conditions Symbol 4/18 Parameter VCC Supply voltage Vicm Common mode input voltage range Toper Operating free air temperature range Value Unit 2.5 to 5.5 V VDD -0.1 to VCC +0.1 V -40 to +125 °C TSV911-TSV912-TSV914 3 Electrical characteristics Electrical characteristics Table 3. Electrical characteristics at VCC = +2.5V VDD = 0V, Vicm = VCC/2, Tamb = 25°C, R L connected to Vcc/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit - 0.1 4.5 - - 7.5 - - 1.5 - - 3 - 2 - µV/°C DC performance Offset voltage TSV91x Vio Tmin. < Top < Tmax. mV TSV91xA Tmin. < Top < Tmax. DVio/DT Input offset voltage drift Iio Input offset current (Vout = Vcc/2) - 1 10(1) pA Iib Input bias current (Vout = Vcc/2) - 1 10(1) pA CMR Common Mode rejection ratio 20 log (∆Vic/∆Vio) 0V to 2.5V, Vout = 1.25V 58 75 - dB Avd Large signal voltage gain RL= 10kΩ, Vout= 0.5V to 2V 80 89 - dB VccVOH High level output voltage RL = 10kΩ RL = 600Ω 15 45 40 150 mV VOL Low level output voltage RL = 10kΩ RL = 600Ω - 15 45 40 150 mV Vo = 2.5V 18 32 - Tmin. < Tamb < Tmax. 16 - - Vo = 0V 18 35 - Tmin. < Tamb < Tmax. 16 - - No load, Vout=Vcc/2 - 0.78 1.1 Tmin. < Top < Tmax. - - 1.1 Gain bandwidth product RL = 2kΩ, CL = 100pF, f = 100kHz - 8 - Fu Unity gain frequency RL = 2kΩ, CL = 100pF, φm Phase margin RL = 2kΩ, CL = 100pF - 45 - Degrees Gm Gain margin RL = 2kΩ, CL = 100pF - 8 - dB SR Slew rate RL = 2kΩ, CL = 100pF, Av=1 - 4.5 - V/µs Isink Iout Isource ICC Supply current (per operator) mA mA AC performance GBP 7.2 MHz MHz 5/18 Electrical characteristics Table 3. TSV911-TSV912-TSV914 Electrical characteristics at VCC = +2.5V VDD = 0V, Vicm = VCC/2, Tamb = 25°C, R L connected to Vcc/2 (unless otherwise specified) Symbol en Parameter Equivalent input noise voltage THD+en Total harmonic distortion Conditions Min. Typ. Max. Unit f=10kHz - 27 - nV -----------Hz G=1, f=1kHz, Rl=2kΩ, BW=22kHz, Vicm=(Vcc+1)/2, Vout=1.1Vpp - 0.001 - % 1. Guaranteed by design. Table 4. Electrical characteristics at VCC = +3.3V VDD = 0V, Vicm = VCC/2, Tamb = 25°C, R L connected to Vcc/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit - 0.1 4.5 - - 7.5 - - 1.5 - - 3 Input offset voltage drift - 2 - µV/°C Input offset current - 1 10(1) pA - 1 10(1) pA DC performance Offset voltage TSV91x Vio Tmin. < Top < Tmax. mV TSV91xA Tmin. < Top < Tmax. DVio Iio Iib Input bias current CMR Common mode rejection ratio 20 log (∆Vic/∆Vio) 0V to 3.3V, Vout = 1.65V 60 78 - dB Avd Large signal voltage gain RL=10kΩ, Vout= 0.5V to 2.8V 80 90 - dB 15 45 40 150 mV mV Vcc-VOH High level output voltage VOL RL = 10kΩ RL = 600Ω - 15 45 40 150 Vo = 3.3V 18 32 - Tmin. < Tamb < Tmax. 16 - - Vo = 0V 18 35 - Tmin. < Tamb < Tmax. 16 - - No load, Vout=Vcc/2 - 0.8 1.1 Tmin. < Top < Tmax. - - 1.1 Gain bandwidth product RL = 2kΩ, CL = 100pF, f = 100kHz - 8 - MHz Unity gain frequency RL = 2kΩ, CL=100pF - 7.2 - MHz Low level output voltage Isink Iout Isource ICC RL = 10kΩ RL = 600Ω Supply current (per operator) mA mA AC performance GBP Fu 6/18 TSV911-TSV912-TSV914 Table 4. Electrical characteristics Electrical characteristics at VCC = +3.3V VDD = 0V, Vicm = VCC/2, Tamb = 25°C, R L connected to Vcc/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit φm Phase margin RL = 2kΩ, CL = 100pF, f = 100kHz - 45 - Degrees Gm Gain margin RL = 2kΩ, CL = 100pF, f = 100kHz - 8 - dB SR Slew rate RL = 2kΩ, CL = 100pF, f = 100kHz, Av=1 - 4.5 - V/µs en Equivalent input noise voltage f=10kHz - 27 - nV -----------Hz G=1, f=1kHz, Rl=2kΩ, BW=22kHz, Vicm=(Vcc+1)/2, Vout=1.9Vpp - 0.00 07 - % THD+en Total harmonic distortion 1. Guaranteed by design. Table 5. Electrical characteristics at VCC = +5V VDD = 0V, Vicm = VCC/2, Tamb = 25°C, R L connected to Vcc/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit - 0.1 4.5 - - 7.5 - - 1.5 - - 3 - 2 - µV/°C pA DC performance Offset voltage TSV91x Vio Tmin. < Top < Tmax. mV TSV91xA Tmin. < Top < Tmax. DVio Input offset voltage drift Iio Input offset current - 1 10(1) Iib Input bias current - 1 10(1) pA CMR Common mode rejection ratio 0V to 5V, Vout = 2.5V 20 log (∆Vic/∆Vio) 62 82 - dB SVR Supply voltage rejection ratio 20 log (∆Vcc/∆Vio) Vcc = 2.5 to 5V 70 86 - dB Avd Large signal voltage gain RL=10kΩ, Vout= 0.5V to 4.5V 80 91 - dB VccVOH High level output voltage RL = 10kΩ RL = 600Ω 15 45 40 150 mV VOL Low level output voltage RL = 10kΩ RL = 600Ω - 15 45 40 150 mV Vo = 5V 18 32 - Tmin. < Tamb < Tmax. 16 - - Vo = 0V 18 35 - Tmin. < Tamb < Tmax. 16 - - Isink Iout Isource mA 7/18 Electrical characteristics Table 5. TSV911-TSV912-TSV914 Electrical characteristics at VCC = +5V VDD = 0V, Vicm = VCC/2, Tamb = 25°C, R L connected to Vcc/2 (unless otherwise specified) Symbol Parameter ICC Supply current (per operator) Conditions Min. Typ. Max. Unit No load, Vout=2.5V - 0.82 1.1 Tmin. < Top < Tmax. - - 1.1 Gain bandwidth product RL = 2kΩ, CL = 100pF, f = 100kHz - 8 - MHz Fu Unity gain frequency RL = 2kΩ, CL=100pF - 7.5 - MHz φm Phase margin RL = 2kΩ, CL=100pF - 45 - Degrees Gm Gain margin RL = 2kΩ, CL=100pF - 8 - dB SR Slew rate RL = 2kΩ, CL = 100pF, AV = 1 - 4.5 - V/µs en Equivalent input noise voltage f=10kHz - 27 - nV -----------Hz G=1, f=1kHz, Rl=2kΩ, BW=22kHz, Vicm=(Vcc+1)/2, Vout=3.6Vpp - 0.0004 - % mA AC performance GBP THD+en Total harmonic distortion 1. Guaranteed by design. 8/18 TSV911-TSV912-TSV914 Figure 1. Electrical characteristics Input offset voltage distribution at T=25°C Figure 2. Input offset voltage distribution at T=125°C 40 140 Vcc=5V Vcc=5V Vicm=2.5V Tamb=25°C 120 Vicm=2.5V Tamb=125°C 30 Quantity of parts Quantity of parts 100 80 60 40 20 10 20 0 -5 -4 -3 -2 -1 0 1 2 3 4 0 -5 5 -4 -3 Figure 3. 1. -2 -1 0 1 2 3 Supply current vs. input common mode voltage at Vcc=2.5V 0 Figure 4. 1. 0 ° ° T=25 C 0.8 0.7 0°C T=-4 ° T=125 C 0.5 0.3 0.7 Supply Current (mA) Supply Current (mA) 0.8 Vcc=2.5V 0.5 0.3 Vcc=5V 0.2 0.0 0.5 1. 0 1.5 2. 0.0 0 2.5 0 1 0 35 Output current vs. output voltage at Figure 6. Vcc=2.5V 0°C Sink T=-4 0 0 4 Vcc=2.5V 35 utput Current (mA) ° T=25 C 5 0 ° T=125 C -5 0 -1 ° T=25 C -15 0 -2 O utput Current (mA) O T=125 C 15 0°C T=-4 -25 0°C Sink T=-4 0 2 Vcc=5V ° T=125 C 15 0 1 ° T=25 C 5 0 ° T=125 C -5 0 -1 ° T=25 C -15 0 -2 0°C T=-4 -25 0 Source 0 Source -3 -3 -35 0 0.0 5 Output current vs. output voltage at Vcc=5V 25 ° 0 2 -4 4 3 25 0 3 0 3 1 2 Input Common Mode Voltage (V) Input Common Mode Voltage (V) 4 ° T=125 C 0°C T=-4 0.2 Figure 5. 5 Supply current vs. input common mode voltage at Vcc=5V T=25 C 0.0 4 Input offset Voltage (mV) Input offset Voltage (mV) -35 0.5 O 1. 0 1.5 utput Voltage (V) 2. 0 2.5 0 0.0 -4 1. 0 O 2. 0 3. 0 4. 0 5. 0 utput Voltage (V) 9/18 Electrical characteristics Voltage gain and phase vs frequency at Vcc=2.5V and Vicm=0.5V Voltage gain and phase vs frequency at Vcc=5.5V and Vicm=0.5V 00 0000 50 5050 2 2 2 160 40 4040 16 1616 30 120 30 3030 12 1212 80 20 2020 8 8 8 10 40 10 1010 0 0 Phase Gain −10 −40 −20 Vcc=2.5V, Vicm=0.5V Cl=100pF, Rl=2kOhms, Vrl=Vcc/2 Tamb=25°C −30 −40 −50 4 10 5 6 10 7 10 00 0 00 0 Phase Phase Phase 00 0 4 4 4 00 0 00 0 Gain Gain Gain 00 0 -4 -4-4 −80 -20 -20 -20 -8 -8-8 −120 -30 -30 -30 00 0 00pF 00pF 00pF ,, R R ,l=2kO l=2kO Rl=2kO hhms, ms, hms, V Vrrl=Vcc/2 V l=Vcc/2 rl=Vcc/2 °° ° -12 -12 -12 Cl=1 Cl=1 Cl=1 −160 -40 -40 -40 −200 -50 -50 -50 44 4 10 1010 10 00 0 00 0 Vcc=5.5V, Vcc=5.5V, Vcc=5.5V, V Vicm= icm= Vicm= .5V .5V .5V 00 0 Tamb=25 Tamb=25 Tamb=25 C CC 55 5 66 6 10 1010 Frequency (Hz) Figure 9. 00 0 -10 -10 -10 8 10 Gain (dB) Gain (dB) 200 40 Phase (°) 50 20 Gain (dB) Figure 8. -16 -16 -16 00 0000 -2 -2-2 77 7 10 1010 88 8 10 1010 10 1010 F Frequency requency Frequency (Hz) (Hz) (Hz) Phase margin vs.capacitive load Figure 10. Phase margin vs.output current 0 80 0 70 6 0 Vicm= .5V 0 Vicm= .5V Vicm=4.5V 0 3 0 2 0 0 5 00 1 0 15 00 2 0 25 Vicm=4.5V 50 40 30 Vcc=5V, Rl=2kOhms Vrl=2.5V Tamb=25°C 0 1 Vicm=1V 60 Vicm=1V 0 4 Phase Margin (°) Phase Margin (°) 5 20 Vcc=5V, Cl=100pF Tamb=25°C 10 00 3 0 35 00 4 0 0 45 −20 −10 Figure 11. 0 10 20 D Capacitive load (pF) C Ouput Current (mA) Positive slew rate Figure 12. Negative slew rate -6 6 0°C T=-4 0°C ° T=25 C T=-4 Negative Slew Rate (V/µs) Positive Slew Rate (V/µs) 5 4 3 ° T=125 C 2 Vin : from 0.5V to Vcc-0.5V SR : calculated from 10% to 90% 0 2.5 10/18 -5 3.0 3.5 4.0 4.5 Supply Voltage (V) 5.0 5.5 ° -4 T=25 C -3 ° T=125 C -2 -1 1 0 2.5 Vin : from 0.5V to Vcc-0.5V SR : calculated from 10% to 90% 3.0 3.5 Phase (°) Phase (°) Figure 7. TSV911-TSV912-TSV914 4.0 4.5 Supply Voltage (V) 5.0 5.5 TSV911-TSV912-TSV914 Electrical characteristics Figure 13. Distorsion + noise vs. frequency Figure 14. Distorsion + noise vs. output voltage 0.01 Vcc=2.5V 0.100 Vcc=3.3V THD + N (%) THD + N (%) Vcc=2.7V Vcc=3.3V 1E-3 Vcc=5V Vcc=5V 0.010 Vout=Vcc-1.4Vpp h Rl=2kO ms 0.001 Gain=1 0 f=1kHz Rl=2kOhms Gain=1 BW=22kHz Vicm=(Vcc+1V)/2 BW=8 kHz Vicm=(Vcc+1V)/2 1E-4 10 100 1000 10000 100000 Frequency (Hz) 0.01 0.1 Output Voltage (V) 1 Figure 15. Noise vs. frequency Equivalent Input Voltage Noise ( nV/VHz) 140 Vcc=5V 120 Tamb=25°C 100 80 Vicm=4.5V 60 Vicm=0.5V 40 20 100 1000 Fre quency ( kHz) 10000 11/18 Package mechanical data 4 TSV911-TSV912-TSV914 Package mechanical data In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com. 4.1 SOT23-5 package SOT23-5L MECHANICAL DATA mm. mils DIM. MIN. MAX. MIN. TYP. MAX. A 0.90 1.45 35.4 57.1 A1 0.00 0.15 0.0 5.9 A2 0.90 1.30 35.4 51.2 b 0.35 0.50 13.7 19.7 C 0.09 0.20 3.5 7.8 D 2.80 3.00 110.2 118.1 E 2.60 3.00 102.3 118.1 E1 1.50 1.75 59.0 68.8 e 0 .95 37.4 e1 1.9 74.8 L 12/18 TYP 0.35 0.55 13.7 21.6 TSV911-TSV912-TSV914 4.2 Package mechanical data MiniSO-8 package 13/18 Package mechanical data 4.3 TSV911-TSV912-TSV914 SO-8 package SO-8 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 e 1.27 0.157 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8˚ (max.) 0.1 0.04 0016023/C 14/18 TSV911-TSV912-TSV914 4.4 Package mechanical data TSSOP14 package TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 15/18 Package mechanical data 4.5 TSV911-TSV912-TSV914 SO-14 package SO-14 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MIN. MAX. TYP. 1.75 0.1 0.068 0.2 a2 0.003 0.007 0.46 0.013 0.018 0.25 0.007 1.65 b 0.35 b1 0.19 C MAX. 0.064 0.5 0.010 0.019 c1 45˚ (typ.) D 8.55 8.75 0.336 E 5.8 6.2 0.228 0.344 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8 ˚ (max.) PO13G 16/18 TSV911-TSV912-TSV914 5 Revision history Revision history Table 6. Document revision history Date Revision 28-Aug-2006 1 Changes First release. 17/18 TSV911-TSV912-TSV914 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18