STMICROELECTRONICS TS1854ID

TS1851-TS1852-TS1854
1.8V input/output rail-to-rail
Low power operational amplifiers
Features
Pin connections (top view)
■
Operates at VCC = 1.8V to 6V
■
Rail-to-rail input and output
■
Extended Vicm (VDD - 0.2V to VCC + 0.2V)
■
Low supply current (120μA)
■
Gain bandwidth product (480kHz)
■
High unity gain stability (able to drive 500pF)
■
ESD tolerance (2kV)
■
Latch-up immunity
■
Available in SOT23-5 micropackage
TS1851ILT
Two-cell battery-powered systems
■
Battery-powered electronic equipment
■
Cordless phones
■
Cellular phones
■
Laptops
■
PDAs
VDD
2
3
5
V CC
4
Inverting input
TS1851ID/IDT
N.C.
8 N.C.
1
Inverting Input 1 2
Non-inverting Input 1
3
-
7 VCC
+
6 Output 2
5 N.C.
V DD 4
TS1852IN-TS1852ID/IDT-TS1852IST
TS1852IPT
Description
The TS185x (single, dual and quad) are
operational amplifiers able to operate with
voltages as low as 1.8V. They feature both input
and output rail-to-rail (1.71 @ VCC= 1.8V,
RL= 2kΩ), 120μA current consumption and
480kHz gain bandwidth product.
8 VCC
Output 1
1
Inverting Input 1
2
-
Non-inverting Input 1
3
+
VDD
4
7 Output 2
-
6 Inverting Input 2
+
5 Non-inverting Input 2
TS1854IN-TS1854ID/IDT-TS1854IPT
14 Output 4
Output 1 1
With such a low consumption and a sufficient
GBP for many applications, this op-amp is very
well-suited for all kinds of battery-supplied and
portable equipment applications.
Inverting Input 1 2
-
-
13 Inverting Input 4
Non-inverting Input 1 3
+
+
12 Non-inverting Input 4
11 VDD
VCC 4
Non-inverting Input 2 5
Inverting Input 2 6
The TS1851 is housed in the space-saving 5-pin
SOT23-5 package which simplifies the board
design (outside dimensions are 2.8mm x 2.9mm).
May 2007
1
Non-inverting input
Applications
■
Output
Output 2 7
Rev 3
+
+
10 Non-inverting Input 3
-
-
9
Inverting Input 3
8
Output 3
1/25
www.st.com
25
Contents
TS1851-TS1852-TS1854
Contents
1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1
DIP8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2
SO-8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3
TSSOP8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.4
MiniSO-8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.5
DIP14 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.6
SO-14 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.7
TSSOP14 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.8
SOT23-5 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2/25
TS1851-TS1852-TS1854
Absolute maximum ratings
1
Absolute maximum ratings
Table 1.
Absolute maximum ratings
Symbol
VCC
Parameter
Supply voltage (1)
Vid
Differential input voltage
Vi
Input voltage
(2)
Value
Unit
7
V
±1
V
Vdd -0.3 to VCC +0.3
V
Toper
Operating free air temperature range
-40 to + 125
°C
Tstg
Storage temperature
-65 to +150
°C
150
°C
Tj
Maximum junction temperature
(3)
Rthja
Thermal resistance junction to ambient
SOT23-5
DIP8
DIP14
miniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
Rthjc
Thermal resistance junction to case
SOT23-5
DIP8
DIP14
miniSO-8
SO-8
SO-14
TSSOP8
TSSOP14
81
41
33
39
40
31
37
32
HBM: human body model(4)
2
kV
200
V
1.5
kV
ESD
MM: machine
model(5)
CDM: charged device model
(6)
Lead temperature (soldering, 10sec)
Output short-circuit duration
250
85
66
190
125
103
120
100
°C/W
°C/W
250
see note
°C
(7)
1. All voltage values, except differential voltage are with respect to network terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If Vid > ±1V, the
maximum input current must not exceed ±1mA. When Vid > ±1V, add an input series resistor to limit input current.
3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all
amplifiers.
4. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a 1.5kΩ resistor
between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
5. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between two pins of the
device with no external series resistor (internal resistor < 5Ω). This is done for all couples of connected pin combinations
while the other pins are floating.
6. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly
to the ground through only one pin. This is done for all pins.
7. Short-circuits from the output to VCC can cause excessive heating. The maximum output current is approximately 48mA,
independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers.
3/25
Operating conditions
2
TS1851-TS1852-TS1854
Operating conditions
Table 2.
Operating conditions
Symbol
4/25
Parameter
Value
Unit
1.8 to 6
V
VCC
Supply voltage
Vicm
Common mode input voltage range
Top = 25°C, 1.8 ≤ VCC ≤ 6V
Tmin < Top < Tmax, 1.8 ≤ VCC ≤ 5.5V
VDD - 0.2 to VCC + 0.2
VDD to VCC
V
Toper
Operating free air temperature range
-40 to + 125
°C
TS1851-TS1852-TS1854
Electrical characteristics
3
Electrical characteristics
Table 3.
Electrical characteristics measured at VCC = +1.8V, Vdd = 0V, with CL & RL connected to
VCC/2, Tamb = 25°C (unless otherwise specified) (1)
Symbol
Parameter
Vio
Input offset voltage
ΔVio
Input offset voltage drift
Conditions
Min.
TS1851/2/4
Tmin ≤ Tamb ≤ Tmax
TS1851A/2A/4A
Tmin ≤ Tamb ≤ Tmax
Typ.
0.1
Max.
Unit
3
6
1
1.5
mV
μV/°C
2
(2)
Iio
Input offset current
Vicm = Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
Iib
Input bias current
Vicm = Vout = VCC/2(2)
Tmin ≤ Tamb ≤ Tmax
Common mode rejection ratio
20 log (ΔVic/ΔVio)
0 ≤Vicm ≤VCC
Tmin ≤ Tamb ≤ Tmax
55
52
85
Large signal voltage gain
Vout = 0.5V to 1.3V
RL = 10kΩ
RL = 2kΩ
80
70
100
88
High level output voltage
Vid = 100mV
RL = 10kΩ
RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 10kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
1.7
1.65
1.7
1.65
1.77
1.7
Low level output voltage
Vid = -100mV
RL = 10kΩ
RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 10kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Output source current
Vid = 100mV, VO = VDD
2
29
Output sink current
Vid = -100mV, VO = VCC
2
46
Supply current (per amplifier)
Vout = VCC/2
AVCL = 1, no load
Tmin ≤ Tamb ≤ Tmax
Gain bandwidth product
RL = 10kΩ, CL = 100pF, f = 100kHz
300
480
kHz
SR
Slew rate
RL = 10kΩ, CL = 100pF, AV = 1
0.1
0.18
V/μs
φm
Phase margin
CL = 100pF
60
Degrees
en
Input voltage noise
f = 1kHz
40
nV/√Hz
0.01
%
CMR
Avd
VOH
VOL
Io
ICC
GBP
THD
Total harmonic distortion
1
9
25
nA
10
50
80
nA
40
62
dB
dB
V
70
90
100
120
mV
mA
120
170
200
μA
1. All parameter limits at temperatures other than 25°C are guaranteed by correlation.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
5/25
Electrical characteristics
Table 4.
TS1851-TS1852-TS1854
Electrical characteristics measured at VCC = +3V, Vdd = 0V, with CL & RL connected to VCC/2,
Tamb = 25°C (unless otherwise specified) (1)
Symbol
Parameter
Vio
Input offset voltage
ΔVio
Input offset voltage drift
Conditions
Min.
Vicm = Vout = VCC/2
TS1851/2/4
Tmin ≤ Tamb ≤ Tmax
TS1851A/2A/4A
Tmin ≤ Tamb ≤ Tmax
Typ.
0.1
Max.
3
6
1
1.5
mV
μV/°C
2
(2)
Unit
Iio
Input offset current
Vicm = Vout = VCC/2
Tmin ≤ Tamb ≤ Tmax
1
9
25
nA
Iib
Input bias current
Vicm = Vout = VCC/2(2)
Tmin ≤ Tamb ≤ Tmax
10
55
85
nA
Common mode rejection ratio
20 log (ΔVic/ΔVio)
0 ≤ Vicm ≤ VCC
Tmin ≤ Tamb ≤ Tmax
60
57
90
dB
Large signal voltage gain
Vout = 0.5V to 2.5V
RL = 10kΩ
RL = 2kΩ
83
74
99
90
dB
High level output voltage
Vid = 100mV
RL = 10kΩ
RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 10kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
2.9
2.85
2.9
2.85
2.96
2.94
Low level output voltage
Vid = -100mV
RL = 10kΩ
RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 10kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Output source current
Vid = 100mV, VO = VDD
2
47
Output sink current
Vid = -100mV, VO = VCC
2
47
Supply current (per amplifier)
Vout = VCC/2
AVCL = 1, no load
Tmin ≤ Tamb ≤ Tmax
Gain bandwidth product
RL = 10kΩ, CL = 100pF, f = 100kHz
370
600
kHz
SR
Slew rate
RL = 10kΩ, CL = 100pF, AV = 1
0.12
0.2
V/μs
φm
Phase margin
CL = 100pF
60
Degrees
en
Input voltage noise
f = 1kHz
40
nV/√Hz
Total harmonic distortion
Vout=2Vpk-pk, AV = -1, f = 1kHz
0.005
%
CMR
Avd
VOH
VOL
Io
ICC
GBP
THD
1. All parameter limits at temperatures other than 25°C are guaranteed by correlation.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
6/25
10
46
V
90
100
120
130
mV
mA
150
200
230
μA
TS1851-TS1852-TS1854
Table 5.
Electrical characteristics
Electrical characteristics measured at VCC = +5V, Vdd = 0V, with CL & RL connected to VCC/2,
Tamb = 25°C (unless otherwise specified) (1)
Symbol
Parameter
Vio
Input offset voltage
ΔVio
Input offset voltage drift
Conditions
Min.
Vicm = Vout = VCC/2
TS1851/2/4
Tmin ≤ Tamb ≤ Tmax
TS1851A/2A/4A
Tmin ≤ Tamb ≤ Tmax
Typ.
Max.
0.1
3
6
1
1.5
mV
μV/°C
2
(2)
Unit
Iio
Input offset current
Vicm = Vout = VCC/2
Tmin ≤Tamb ≤Tmax
1
9
25
nA
Iib
Input bias current
Vicm = Vout = VCC/2(2)
Tmin ≤Tamb ≤Tmax
16
63
93
nA
CMR
Common mode rejection ratio
20 log (ΔVic/ΔVio)
0 ≤Vicm ≤VCC
Tmin ≤Tamb ≤Tmax
65
62
95
dB
SVR
Supply voltage rejection ratio
20 log (ΔVcc/ΔVio)
VCC = 1.8 to 5V
70
90
dB
Avd
Large signal voltage gain
Vout = 0.5V to 4V
RL = 10kΩ
RL = 2kΩ
85
77
97
93
dB
High level output voltage
Vid = 100mV
RL = 10kΩ
RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 10kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
4.85
4.8
4.85
4.8
4.95
4.91
Low level output voltage
Vid = -100mV
RL = 10kΩ
RL = 2kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 10kΩ
Tmin ≤ Tamb ≤ Tmax, RL = 2kΩ
Output source current
Vid = 100mV, VO = VDD
2
48
Output sink current
Vid = -100mV, VO = VCC
2
48
Supply current (per amplifier)
Vout = VCC/2
AVCL = 1, no load
Tmin ≤ Tamb ≤ Tmax
Gain bandwidth product
RL = 10kΩ, CL = 100pF, f = 100kHz
380
630
kHz
SR
Slew rate
RL = 10kΩ, CL = 100pF, AV = 1
0.13
0.25
V/μs
φm
Phase margin
CL = 100pF
60
Degrees
en
Input voltage noise
f = 1kHz
40
nV/√Hz
Total harmonic distortion
Vout=2Vpk-pk, AV=-1, f = 1kHz
0.01
%
VOH
VOL
Io
ICC
GBP
THD
40
80
V
180
200
180
200
mV
mA
162
220
250
μA
1. All parameter limits at temperatures other than 25°C are guaranteed by correlation.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
7/25
Electrical characteristics
Figure 1.
TS1851-TS1852-TS1854
Input offset voltage distribution
Figure 2.
400
488 pieces tested
Vcc = 10V
Temp = +25°C
80
60
40
Input Voltage Drift (µV)
100
Quantity of Pieces
Input offset voltage vs. temperature
Vcc = 1.8V
300
200
100
Vcc = 10V
0
-100
-200
20
-300
2
-400
-40
Input bias current vs. temperature
Figure 4.
0
-2.
-1.6 -1.2 -.8
-.4
0
.4
.8
1.2
1.6
-20
0
20
Input Offset Voltage (mV)
Figure 3.
Input bias current (nA)
Input bias current (nA)
Vcc = 1.8V
Vicm = 0.9V
-2
-4
-6
-8
-10
-12
-40 -20
0
Input bias current vs. temperature
-6
-8
-10
20
40
60
80 100 120 140
Figure 6.
Supply current/amplifier vs. supply
voltage
200
Vcc = 5V
Vicm = 2.5V
-4
-6
-8
-10
-12
-40 -20
-4
Temperature (°C)
Supply Current (µA)
Input bias current (nA)
-2
Vcc = 3V
Vicm = 1.5V
-2
-12
-40 -20 0
20 40 60 80 100 120 140
Temperature (°C)
0
150
Tamb = 25°C
100
50
0
0
20
40
60
80 100 120 140
Temperature (°C)
8/25
Input bias current vs. temperature
0
0
Figure 5.
40 60 80 100 120 140
Temperature (°C)
0
2
4
6
Supply Voltage (V)
8
TS1851-TS1852-TS1854
Supply current/amplifier vs.
temperature
Figure 8.
170
Vcc = 5V
Vcc = 3V
140
130
Vcc = 1.8V
120
110
100
90
-40 -20 0
20
40
60
110
Vcc = 1.8V
100
90
80
70
60
80 100 120 140
-40 -20 0
Temperature (°C)
Common mode rejection vs.
temperature
Figure 10. Gain and phasis vs. frequency
q
70
110
Vcc = 3V
50
90
80
70
60
-50
0
50
100
40
100
20
80
10
60
40
1E+6
1E+4
1E+5
Frequency (Hz)
180
RL = 10K
CL = 100 pF
Vcc = 5V
60
50
80
70
60
-40 -20 0
100
phase
70
Vcc = 2V
Vicm = 1V
90
20 40 60 80 100 120 140
Temperature (°C)
140
Figure 12. Gain and phasis vs. frequency
Gain (dB)
Supply Voltage Rejection (dB)
110
160
120
30
Temperature (°C)
Figure 11. Supply voltage rejection vs.
temperature
180
gain
0
1E+3
150
y
RL = 10K
CL = 100 pF
Vcc = 1.8V
60
100
Gain (dB)
Common Mode Rejection (dB)
Figure 9.
20 40 60 80 100 120 140
Temperature (°C)
Phase (°)
150
Common mode rejection vs.
temperature
40
160
140
120
gain
30
100
phase
20
80
10
60
0
1E+3
Phase (°)
Supply Current (µA)
160
Common Mode Rejection (dB)
Figure 7.
Electrical characteristics
40
1E+4
1E+5
Frequency (Hz)
1E+6
9/25
Electrical characteristics
TS1851-TS1852-TS1854
Figure 13. Common mode rejection vs.
temperature
Figure 14. Supply voltage rejection vs.
temperature
110
Supply Voltage Rejection (dB)
Common Mode Rejection (dB)
110
Vcc = 5V
100
90
80
70
Vcc = 3V
Vicm = 1.5V
100
90
80
70
60
60
-40
0
40
-20
80
20
120
60
-40
100
0
140
40
-20
Temperature (°C)
140
110
Vcc = 1.8V
Vcc = 5V
Vicm = 2.5V
100
Open Loop Gain (dB)
Supply Voltage Rejection (dB)
120
100
Figure 16. Open loop gain vs. temperature
110
90
80
70
60
RL = 10 kohms
100
RL = 2 kohms
90
80
70
-40
0
-20
40
20
80
60
120
100
-40
140
0
-20
40
20
Temperature (°C)
80
60
120
100
140
Temperature (°C)
Figure 17. Open loop gain vs. temperature
Figure 18. Open loop gain vs. temperature
110
110
RL = 10 kohms
VCC = 5V
Vcc = 3V
RL = 10 kohms
Open Loop Gain (dB)
Open Loop Gain (dB)
60
Temperature (°C)
Figure 15. Supply voltage rejection vs.
temperature
100
RL = 2 kohms
90
80
100
RL = 2 kohms
90
80
70
70
-40
0
-20
40
20
80
60
Temperature (°C)
10/25
80
20
-40
120
100
140
0
-20
40
20
80
60
Temperature (°C)
120
100
140
TS1851-TS1852-TS1854
Electrical characteristics
Figure 19. High level output voltage vs.
temperature
Figure 20. Low level output voltage vs.
temperature
Voltage Referenced to Gnd (mV)
Voltage Referenced to VCC (mV)
55
RL = 10 kohms
50
Vcc = 5V
45
40
Vcc = 3V
35
30
Vcc = 1.8V
25
20
-40
0
40
-20
20
80
55
45
100
Vcc = 3V
40
35
Vcc = 1.8V
30
25
20
120
60
-40
140
0
-20
Voltage Referenced to Gnd (mV)
Voltage Referenced to VCC (mV)
RL = 2 kohms
Vcc = 5V
100
90
80
Vcc = 3V
70
Vcc = 1.8V
60
50
40
-20
20
80
60
100
90
Vcc = 3V
80
Vcc = 1.8V
70
60
50
40
-40
0
-20
140
Isink, Vcc = 3V
40
120
100
140
Figure 24. Output current vs. temperature
Vid = 1V
Isource, Vcc = 1.8V
Isource, Vcc = 3V
-40
Isource, Vcc = 5V
T = 25 °C
sink
50
20
-20
80
60
60
Isink, Vcc = 1.8V
0
40
20
Temperature (°C)
Output Current (mA)
Output Current (mA)
60
Vcc = 5V
RL = 2 kohms
100
120
Figure 23. Output current vs. temperature
Isink, Vcc = 5V
140
110
Temperature (°C)
80
120
100
Figure 22. Low level output voltage vs.
temperature
110
40
80
60
Temperature (°C)
Figure 21. High level output voltage vs.
temperature
0
40
20
Temperature (°C)
-40
Vcc = 5V
RL = 10 kohms
50
T = 125 °C
40
T = -40 °C
30
20
Vcc = 1.8V
Vid = 0.1V
Vicm = 0.9V
10
0
-10
T = -40 °C
-20
T = 125 °C
-30
T = 25 °C
source
-40
-60
-40
0
-20
40
20
80
60
Temperature (°C)
0.0
120
100
140
1.0
0.5
2.0
1.5
Output Voltage (V)
11/25
Electrical characteristics
TS1851-TS1852-TS1854
Figure 25. Output current vs. output voltage
Figure 26. Output current vs. output voltage
80
80
sink
T = -40 °C
40
T = 125 °C
20
Vcc = 3V
Vid = 0.1V
Vicm = 1.5V
0
T = 125 °C
-20
T = 25 °C
sink
60
Output Current (mA)
Output Current (mA)
60
T = 25 °C
T = -40 °C
T = 125 °C
40
T = -40 °C
20
Vcc = 5V
Vid = 0.1V
Vicm = 2.5V
0
T = -40 °C
-20
T = 25 °C
-40
-40
T = 25 °C
source
source
T = 125 °C
-60
-60
0.0
1.0
2.0
0.5
1.5
0.0
3.0
2.0
Figure 27. Gain and phasis vs. frequency
RL = 10K
CL = 100 pF
VCC = 5V
40
160
140
120
gain
30
Gain-Bandwith Product (MHz)
Gain (dB)
0.65
180
100
phase
20
80
10
60
0
1E+3
5.0
Figure 28. Gain bandwidth product vs.
temperature
Phase (°)
70
50
3.0
Output Voltage (V)
Output Voltage (V)
60
4.0
1.0
2.5
40
0.60
Vcc = 3V
0.55
Vcc = 1.8V
0.50
0.45
1E+5
-40
1E+4
Vicm = Vcc/2
RL = 10kohms
CL = 100 pF
Vcc = 5V
1E+6
0
-20
40
20
Frequency (Hz)
80
60
120
100
140
Temperature (°C)
Figure 29. Gain bandwidth product vs. supply Figure 30. Slew rate vs. temperature
voltage
0.19
RL = 2 kohms
CL = 300 pF
Vicm = Vcc/2
T = 25°C
750
700
0.18
Slew Rate (V/µs)
Gain-Bandwith Product (MHz)
800
650
600
550
500
0.16
negative Slew Rate
positive Slew Rate
0.15
0.14
0.13
0.12
450
0
2
1
4
3
Supply Voltage (V)
12/25
0.17
VCC = 1.8V
gain = +1
Vin = 0.4 to 1.4V
RL = 10kohms
CL = 100 pF
0.11
-40
6
5
7
0
-20
40
20
80
60
Temperature (°C)
120
100
140
TS1851-TS1852-TS1854
Electrical characteristics
Figure 31. Slew rate vs. temperature
0.21
0.18
0.21
0.20
Slew Rate (V/µs)
Slew Rate (V/µs)
0.19
0.22
positive Slew Rate
VCC = 3V
gain = +1
Vin = 1 to 2V
RL = 10kohms
CL = 100 pF
0.20
Figure 32. Slew rate vs. temperature
negative Slew Rate
0.17
0.16
0.15
0.19
negative Slew Rate
0.17
0.16
0.15
0.13
0.14
0.13
-40
0
40
-20
20
80
120
60
100
-40
140
0
-20
80
120
60
100
140
Temperature (°C)
Figure 33. Phase margin vs. load capacitor
Figure 34. Phase margin vs. output current
70
85
VCC = 3V
gain = -1
60
80
50
Phase Margin (°)
Phase Margin (°)
40
20
Temperature (°C)
40
30
20
10
VCC = 3V
RL = 2 kohms
CL = 100 pF
75
70
65
60
0
-10
55
10
1000
100
-10
0
10000
5
DC Output Current (mA)
Figure 35. Equivalent input noise vs.
frequency
Figure 36. Distortion vs. output voltage
50
10.000
40
Distortion (%)
1.000
30
20
10
10
-5
Load Capacitor (pF)
Equivalent Input Noise (nV/sqr(Hz))
positive Slew Rate
0.18
0.14
0.12
VCC = 5V
gain = +1
Vin = 2 to 3V
RL = 10kohms
CL = 100 pF
VCC = 1.8V
gain = 100
Rs = 100 ohms
0
1E+1
VCC = 1.8V
f = 1kHz
T = 25°C
gain = -1
RL = 2kohms
RL = 10kohms
0.100
0.010
1E+3
1E+2
1E+5
1E+4
Frequency (Hz)
0.001
0.000
0.200
0.100
0.400
0.300
0.600
0.500
0.800
0.700
Output Voltage (V)
13/25
Electrical characteristics
TS1851-TS1852-TS1854
Figure 37. Distortion vs. output voltage
Figure 38. Distortion vs. output voltage
10.000
10.000
1.000
Distortion (%)
Distortion (%)
1.000
VCC = 3V
f = 1kHz
RL = 10K
T = 25°C
gain = -1
0.100
0.001
0.000
0.400
0.200
0.800
0.600
1.200
1.000
0.100
RL = 2kohms
Figure 39. Distortion vs. frequency
1.000
VCC = 3V
Vout = 2Vpp
T = 25°C
gain = -1
0.100
RL = 2kohms
0.010
RL = 10kohms
0.001
1E+1
1E+3
1E+2
1E+5
1E+4
Frequency (Hz)
0.001
0.000
1.000
0.500
2.000
1.500
Output Voltage (V)
Output Voltage (V)
Distortion (%)
RL = 10kohms
0.010
0.010
14/25
VCC = 5V
f = 1kHz
T = 25°C
gain = -1
TS1851-TS1852-TS1854
4
Package information
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in
ECOPACK® packages. These packages have a lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
15/25
Package information
4.1
TS1851-TS1852-TS1854
DIP8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
5.33
Max.
0.210
A1
0.38
0.015
A2
2.92
3.30
4.95
0.115
0.130
0.195
b
0.36
0.46
0.56
0.014
0.018
0.022
b2
1.14
1.52
1.78
0.045
0.060
0.070
c
0.20
0.25
0.36
0.008
0.010
0.014
D
9.02
9.27
10.16
0.355
0.365
0.400
E
7.62
7.87
8.26
0.300
0.310
0.325
E1
6.10
6.35
7.11
0.240
0.250
0.280
e
2.54
0.100
eA
7.62
0.300
eB
L
16/25
Inches
10.92
2.92
3.30
3.81
0.430
0.115
0.130
0.150
TS1851-TS1852-TS1854
4.2
Package information
SO-8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.75
0.069
A1
0.10
A2
1.25
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
H
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
0.25
Max.
0.004
0.010
0.049
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
1°
8°
1°
8°
ccc
0.10
0.004
17/25
Package information
4.3
TS1851-TS1852-TS1854
TSSOP8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.2
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
1.05
0.031
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
e
18/25
Inches
1.00
0.65
k
0°
L
0.45
0.60
0.006
0.039
0.041
0.0256
8°
0°
0.75
0.018
8°
0.024
L1
1
0.039
aaa
0.1
0.004
0.030
TS1851-TS1852-TS1854
4.4
Package information
MiniSO-8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Typ.
1.1
Max.
0.043
A1
0.05
0.10
0.15
0.002
0.004
0.006
A2
0.78
0.86
0.94
0.031
0.034
0.037
b
0.25
0.33
0.40
0.010
0.013
0.016
c
0.13
0.18
0.23
0.005
0.007
0.009
D
2.90
3.00
3.10
0.114
0.118
0.122
E
4.75
4.90
5.05
0.187
0.193
0.199
E1
2.90
3.00
3.10
0.114
0.118
0.122
e
0.65
K
0°
L
0.40
L1
0.55
0.026
6°
0°
0.70
0.016
0.10
6°
0.022
0.028
0.004
19/25
Package information
4.5
TS1851-TS1852-TS1854
DIP14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
a1
0.51
B
1.39
Typ.
Max.
Min.
Typ.
Max.
0.020
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
Z
20/25
Inches
3.3
1.27
0.130
2.54
0.050
0.100
TS1851-TS1852-TS1854
4.6
Package information
SO-14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
a1
Inches
Max.
Min.
Typ.
1.75
0.1
0.2
a2
Max.
0.068
0.003
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45° (typ.)
D
8.55
8.75
0.336
0.344
E
5.8
6.2
0.228
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
0.68
0.026
8° (max.)
21/25
Package information
4.7
TS1851-TS1852-TS1854
TSSOP14 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Inches
Max.
Min.
Max.
1.2
A1
0.05
A2
0.8
b
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
1
e
0.65 BSC
K
0°
L
0.45
A
0.0256 BSC
8°
0°
0.60
0.75
0.018
e
c
8°
0.024
0.030
A2
A1
b
K
E1
PIN 1 IDENTIFICATION
1
L
E
D
22/25
Typ.
TS1851-TS1852-TS1854
4.8
Package information
SOT23-5 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
Mils
Max.
Min.
Typ.
Max.
A
0.890
1.120
35.05
44.12
A1
0.010
0.100
0.39
3.94
A2
0.880
1.020
34.65
b
0.300
0.500
11.81
19.69
C
0.080
0.200
3.15
7.88
D
2.800
3.040
110.26
E
2.100
2.64
82.70
E1
1.200
1.400
47.26
0.950
2.900
1.300
37.41
114.17
51.19
0.950
37.41
e1
1.900
74.82
0.400
L1
k
0.600
15.75
0.540
0°
119.72
103.96
e
L
40.17
55.13
23.63
21.27
8°
0°
8°
7110469/A
23/25
Ordering information
TS1851-TS1852-TS1854
5
Ordering information
Table 6.
Order codes
Temperature
range
Part number
Package
Packing
Marking
Tube or
Tape & reel
1851I
SO-8
TS1851ID/IDT
TS1851IAID/AIDT
TS1851ILT
K161
SOT23-5L
Tape & reel
TS1851AILT
K162
TS1852IN
1852IN
DIP8
Tube
TS1852AIN
1852AIN
TS1852ID/IDT
Tube or
Tape & reel
SO-8
TS1852AID/AIDT
-40°C to +125°C
TS1852IPT
TS1852AIPT
1852I
1852AI
1852I
TSSOP8
(Thin shrink outline package)
Tape & reel
MiniSO-8
Tape & reel
1852A
TS1852IST
K161
TS1852AIST
K162
TS1854IN/AIN
DIP14
Tube
1854IN
Tube or
Tape & reel
1854I
SO-14
TS1854ID/IDT
TS1854AID/AIDT
TS1854IPT
TSSOP14
(Thin shrink outline package)
TS1854AIPT
6
1851AI
1854AI
1854I
Tape & reel
1854A
Revision history
Date
Revision
Feb-2002
1
First release.
May-2005
2
Modifications on AMR Table 1 on page 3 (explanation of Vid and Vi limits)
3
Added limits in temperature in Table 3, Table 4, and Table 5.
Added SVR in Table 5 (SVR parameter removed from Table 3 and Table 4).
Added equivalent input voltage noise in Table 3, Table 4, and Table 5.
Added Rthjc values in Table 1 on page 3.
Updated Table 6: Order codes.
22-May-2007
24/25
Changes
TS1851-TS1852-TS1854
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
25/25