ONSEMI MC10E101

SEMICONDUCTOR TECHNICAL DATA
The MC10E/100E101 is a quad 4-input OR/NOR gate.
• 500ps Max. Propagation Delay
• Extended 100E VEE Range of – 4.2V to – 5.46V
• 75kΩ Input Pulldown Resistors
QUAD 4-INPUT
OR/NOR GATE
Pinout: 28-Lead PLCC (Top View)
D3a
D3b
D3c
D3d VCCO Q3
Q3
25
24
23
22
19
21
20
D2d
26
18
Q2
D2c
27
17
Q2
D2b
28
16
VCC
VEE
1
15
Q1
D2a
2
14
Q1
D1d
3
13
Q0
D1c
4
12
Q0
5
6
7
8
9
D1b
D1a
D0d
D0c
D0b
10
FN SUFFIX
PLASTIC PACKAGE
CASE 776-02
11
D0a VCCO
* All VCC and VCCO pins are tied together on the die.
LOGIC DIAGRAM
D0a
D0b
PIN NAMES
Q0
D0c
D0d
Q0
D1a
D1b
D1c
Q1
Pin
Function
D0a – D3d
Data Inputs
Q0 – Q3
True Outputs
Q0 – Q3
Inverting Outputs
Q1
D1d
D2a
D2b
Q2
D2c
D2d
Q2
D3a
D3b
Q3
D3c
D3d
Q3
12/93
 Motorola, Inc. 1996
2–1
REV 2
MC10E101 MC100E101
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0°C
Symbol
Characteristic
IIH
Input HIGH Current
IEE
Power Supply Current
10E
100E
min
typ
25°C
max
min
typ
150
85°C
max
min
typ
150
max
Unit
150
µA
Condition
mA
30
30
36
36
30
30
36
36
30
35
36
42
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0°C
Symbol
Characteristic
tPLH
tPHL
Propagation Delay to Output
D to Q
tSKEW
tSKEW
Within-Device Skew
Within-Gate Skew
tr
tf
Rise/Fall Time
20 - 80%
25°C
85°C
min
typ
max
min
typ
max
min
typ
max
200
350
500
200
350
500
200
350
500
Unit
Condition
ps
50
25
50
25
50
25
ps
1
2
ps
300
380
575
300
380
575
300
380
575
1. Within-device skew is defined as identical transitions on similar paths through a device.
2. Within-gate skew is defined as the variation in propagation delays of a gate when driven from its different inputs.
MOTOROLA
2–2
ECLinPS and ECLinPS Lite
DL140 — Rev 4
MC10E101 MC100E101
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776–02
ISSUE D
0.007 (0.180)
B
Y BRK
-N-
T L –M
M
U
0.007 (0.180)
X
G1
M
S
N
T L –M
S
S
N
S
D
Z
-L-
-M-
D
W
28
V
1
C
A
0.007 (0.180)
M
R
0.007 (0.180)
M
T L –M
S
T L –M
S
N
S
N
S
H
S
N
S
0.007 (0.180)
M
T L –M
N
S
S
0.004 (0.100)
G
J
-T-
K
SEATING
PLANE
F
VIEW S
G1
T L –M
S
N
0.007 (0.180)
M
T L –M
S
N
S
VIEW S
S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIM G1, TRUE POSITION TO BE MEASURED
AT DATUM -T-, SEATING PLANE.
3. DIM R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
ECLinPS and ECLinPS Lite
DL140 — Rev 4
T L –M
K1
E
S
S
VIEW D-D
Z
0.010 (0.250)
0.010 (0.250)
2–3
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.485 0.495
0.485 0.495
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
0.020
—
0.025
—
0.450 0.456
0.450 0.456
0.042 0.048
0.042 0.048
0.042 0.056
—
0.020
2°
10°
0.410 0.430
0.040
—
MILLIMETERS
MIN
MAX
12.32 12.57
12.32 12.57
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
—
0.64
—
11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
—
0.50
2°
10°
10.42 10.92
1.02
—
MOTOROLA
MC10E101 MC100E101
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MOTOROLA
2–4
*MC10E101/D*
MC10E101/D
ECLinPS and ECLinPS Lite
DL140 — Rev 4