ONSEMI MC100E160

SEMICONDUCTOR TECHNICAL DATA
The MC10E/100E160 is a 12-bit parity generator/checker. The Q
output is HIGH when an odd number of inputs are HIGH. A HIGH on the
Enable input (EN) forces the Q output LOW.
The E160 also features an output register. Multiplexers direct the
register input, giving the option of holding present data by asserting
HOLD LOW, or of shifting data in through the S-IN pin by asserting SHIFT
HIGH. The output register itself is clocked by a positive edge on CLK1 or
CLK2 (or both). A HIGH on the reset pin (R) overrides to force the Y
output LOW.
•
•
•
•
•
•
•
•
12-BIT PARITY
GENERATOR/CHECKER
Provides Odd-HIGH Parity of 12 Inputs
Shiftable Output Register with Hold
900ps Max. D to Q/Q Output
Enable
Asynchronous Register Reset
Dual Clocks
Extended 100E VEE Range of – 4.2V to – 5.46V
75kΩ Input Pulldown Resistors
FN SUFFIX
PLASTIC PACKAGE
CASE 776-02
Pinout: 28-Lead PLCC (Top View)
D4
D3
D2
D1
D0
EN
VCCO
25
24
23
22
21
20
19
D5
26
18
Q
D6
27
17
Q
D7
28
16
VCC
VEE
1
15
Y
D8
2
14
Y
D9
3
13
VCCO
D10
4
12
NC
5
6
7
8
9
10
11
D11 HOLD S-IN SHIFT CLK1 CLK2 R
* All VCC and VCCO pins are tied together on the die.
PIN NAMES
Pin
D0 – D11
S-IN
EN
HOLD
SHIFT
CLK1, CLK2
R
Q, Q
Y, Y
LOGIC DIAGRAM
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
Q
0
MUX
1 SEL
EN
HOLD
Function
Data Inputs
Serial Data Input
Enable, active LOW
Hold, active LOW
Shift, active HIGH
Clock Inputs
Reset Inputs
Direct Output
Register Output
S-IN
SHIFT
CLK1
CLK2
R
12/93
 Motorola, Inc. 1996
2–1
REV 2
0
MUX
1 SEL
Y
D
R
Y
MC10E160 MC100E160
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0°C
Symbol
Characteristic
IIH
min
typ
max
min
85°C
typ
max
min
typ
max
Unit
Condition
µA
Input HIGH Current
CLK1, CLK2
R
All Other Inputs
IEE
25°C
200
300
150
Power Supply Current
10E
100E
200
300
150
200
300
150
mA
82
82
98
98
82
82
98
98
82
94
98
113
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0°C
Symbol
25°C
85°C
Characteristic
min
typ
max
min
typ
max
min
typ
max
tPLH
tPHL
Propagation Delay to Output
D to Q
En to Q
CLK to Y
R to Y
400
300
275
275
650
550
500
500
950
750
700
725
400
300
275
275
650
550
500
500
950
750
700
725
400
300
275
275
650
550
500
500
950
750
700
725
ts
Setup Time
D
HOLD
S-IN
SHIFT
1200
600
350
500
900
300
150
250
1200
600
350
500
900
300
150
250
1200
600
350
500
900
300
150
250
Hold Time
D
HOLD
S-IN
SHIFT
– 400
100
300
200
– 900
– 300
–150
– 250
– 400
100
300
200
– 900
– 300
–150
– 250
– 400
100
300
200
– 900
– 300
–150
– 250
300
450
300
450
300
450
th
tr
tf
Rise/Fall Time
20 - 80%
Unit
Condition
ps
ps
ps
ps
650
650
650
1. Within a device skew is guaranteed for identical transitions on similar paths through a device.
MOTOROLA
2–2
ECLinPS and ECLinPS Lite
DL140 — Rev 4
MC10E160 MC100E160
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776–02
ISSUE D
0.007 (0.180)
B
Y BRK
-N-
T L –M
M
U
0.007 (0.180)
X
G1
M
S
N
T L –M
S
S
N
S
D
Z
-L-
-M-
D
W
28
V
1
C
A
0.007 (0.180)
M
R
0.007 (0.180)
M
T L –M
S
T L –M
S
N
S
N
S
H
S
N
S
0.007 (0.180)
M
T L –M
N
S
S
0.004 (0.100)
G
J
-T-
K
SEATING
PLANE
F
VIEW S
G1
T L –M
S
N
0.007 (0.180)
M
T L –M
S
N
S
VIEW S
S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIM G1, TRUE POSITION TO BE MEASURED
AT DATUM -T-, SEATING PLANE.
3. DIM R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
ECLinPS and ECLinPS Lite
DL140 — Rev 4
T L –M
K1
E
S
S
VIEW D-D
Z
0.010 (0.250)
0.010 (0.250)
2–3
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.485 0.495
0.485 0.495
0.165 0.180
0.090 0.110
0.013 0.019
0.050 BSC
0.026 0.032
0.020
—
0.025
—
0.450 0.456
0.450 0.456
0.042 0.048
0.042 0.048
0.042 0.056
—
0.020
2°
10°
0.410 0.430
0.040
—
MILLIMETERS
MIN
MAX
12.32 12.57
12.32 12.57
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
—
0.64
—
11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
—
0.50
2°
10°
10.42 10.92
1.02
—
MOTOROLA
MC10E160 MC100E160
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MOTOROLA
2–4
*MC10E160/D*
MC10E160/D
ECLinPS and ECLinPS Lite
DL140 — Rev 4