SEMICONDUCTOR TECHNICAL DATA The MC10E/100E212 is a scannable registered ECL driver typically used as a fan-out memory address driver for ECL cache driving. In a VLSI array based CPU design, use of the E212 allows the user to conserve array output cell functionality and also output pins. The input shift register is designed with control logic which greatly facilitates its use in boundary scan applications. • • • • • • 3-BIT SCANNABLE REGISTERED ADDRESS DRIVER Scannable Version E112 Driver 1025ps Max. CLK to Output Dual Differential Outputs Master Reset Extended 100E VEE Range of – 4.2V to – 5.46V Internal 75kΩ Input Pulldown Resistors Pinout: 28-Lead PLCC (Top View) SHIFT MR 25 LOAD 26 19 18 Q2b CLK 27 17 Q2a D2 28 16 VCC VEE 1 15 Q1b D1 2 14 Q1a D0 3 13 Q1b S-IN 4 12 Q1a 5 24 FN SUFFIX PLASTIC PACKAGE CASE 776-02 NC S-OUTVCCO Q2b Q2a 6 23 7 22 8 21 9 20 10 LOGIC DIAGRAM S-OUT Q2b Q2a D Q D2 Q2a Q2b 11 NC VCCO Q0a Q0b Q0a Q0b VCCO * All VCC and VCCO pins are tied together on the die. Q1b Q1a D Q D1 Q1a Q1b PIN NAMES Pin D0 – D2 S-IN LOAD SHIFT CLK MR S-OUT Q[0:2]a, Q[0:2]b Q[0:2]a, Q[0:2]b Function Data Inputs Scan Input LOAD/HOLD Control Scan Control Clock Reset Scan Output True Outputs Inverting Outputs Q D0 Q0a Q0b S-IN LOAD SHIFT CLK MR 12/93 Motorola, Inc. 1996 Q0b Q0a D 2–1 REV 2 MC10E212 MC100E212 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic IIH Input HIGH Current IEE Power Supply Current 10E 100E min typ 25°C max min typ 150 85°C max min typ 150 max Unit 150 µA Condition mA 80 80 96 96 80 80 96 96 80 92 96 110 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic 25°C 85°C min typ max min typ max min typ max 1025 1025 1025 575 575 575 800 800 800 1025 1025 1025 575 575 575 800 800 800 1025 1025 1025 Unit Condition tPLH tPHL Propagation Delay to Output CLK MR CLK to S-OUT 575 575 575 800 800 800 ts Setup Time D SHIFT LOAD S-IN 175 150 225 150 25 – 50 50 – 50 175 150 225 150 25 – 50 50 – 50 175 150 225 150 25 – 50 50 – 50 Hold Time D SHIFT LOAD S-IN 250 300 225 300 25 100 0 100 250 300 225 300 25 100 0 100 250 300 225 300 25 100 0 100 tRR Reset Recovery 600 350 600 350 600 350 ps tSKEW Within-Device Skew 100 100 100 ps 1 tSKEW Within-Gate Skew 50 50 50 ps 2 tr tf Rise/Fall Times 20 - 80% th ps ps ps ps 275 425 650 275 425 650 275 425 650 1. Within-device skew is defined as identical transitions on similar paths through a device. 2. Within-gate skew is defined as the difference in delays between various outputs of a gate when driven from the same input. FUNCTION TABLE LOAD SHIFT MR MODE L H X X L L H X L L L H Load Hold Shift Reset MOTOROLA 2–2 ECLinPS and ECLinPS Lite DL140 — Rev 4 MC10E212 MC100E212 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776–02 ISSUE D 0.007 (0.180) B Y BRK -N- T L –M M U 0.007 (0.180) X G1 M S N T L –M S S N S D Z -L- -M- D W 28 V 1 C A 0.007 (0.180) M R 0.007 (0.180) M T L –M S T L –M S N S N S H S N S 0.007 (0.180) M T L –M N S S 0.004 (0.100) G J -T- K SEATING PLANE F VIEW S G1 T L –M S N 0.007 (0.180) M T L –M S N S VIEW S S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). ECLinPS and ECLinPS Lite DL140 — Rev 4 T L –M K1 E S S VIEW D-D Z 0.010 (0.250) 0.010 (0.250) 2–3 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 — 0.025 — 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 — 0.020 2° 10° 0.410 0.430 0.040 — MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 — 0.64 — 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 — 0.50 2° 10° 10.42 10.92 1.02 — MOTOROLA MC10E212 MC100E212 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–4 *MC10E212/D* MC10E212/D ECLinPS and ECLinPS Lite DL140 — Rev 4