SEMICONDUCTOR TECHNICAL DATA The MC10E/100E142 is a 9-bit shift register, designed with byte-parity applications in mind. The E142 performs serial/parallel in and serial/parallel out, shifting in one direction. The nine inputs D0 – D8 accept parallel input data, while S-IN accepts serial input data. The Qn outputs do not need to be terminated for the shift operation to function. To minimize noise and power, any Q output not used should be left unterminated. 9-BIT SHIFT REGISTER • • • • • • 700MHz Min. Shift Frequency 9-Bit for Byte-Parity Applications Asynchronous Master Reset Dual Clocks Extended 100E VEE Range of – 4.2V to – 5.46V 75kΩ Input Pulldown Resistors The SEL (Select) input pin is used to switch between the two modes of operation — SHIFT and LOAD. The shift direction is from bit 0 to bit 8. Input data is accepted by the registers a set-up time before the positive going edge of CLK1 or CLK2; shifting is also accomplished on the positive clock edge. A HIGH on the Master Reset pin (MR) asynchronously resets all the resisters to zero. SEL D8 D7 D6 D5 VCCO Q8 25 24 23 22 21 20 19 FN SUFFIX PLASTIC PACKAGE CASE 776-02 MR 26 18 Q7 CLK1 27 17 Q6 CLK2 28 VEE 1 S-IN 2 16 Pinout: 28-Lead PLCC (Top View) VCC 15 Q5 14 VCCO D0 3 13 Q4 D1 4 12 Q3 5 6 7 8 9 10 LOGIC DIAGRAM S-IN D0 1 0 D D1 1 0 D D2 1 0 D D3 1 0 D D8 1 0 D Q Q0 Q Q1 Q Q2 Q Q3 Q Q8 11 D2 D3 D4 VCCO Q0 Q1 Q2 * All VCC and VCCO pins are tied together on the die. PIN NAMES Pin D0 – D8 S-IN SEL CLK1, CLK2 MR Q0 – Q8 Function Parallel Data Inputs Serial Data Input Mode Select Input Clock Inputs Master Reset Data Outputs SEL CLK1 CLK2 FUNCTIONS SEL L H Mode MR Load Shift 12/93 Motorola, Inc. 1996 2–1 REV 2 MC10E142 MC100E142 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic IIH Input HIGH Current IEE Power Supply Current 10E 100E min typ 25°C max min typ 85°C max 150 min typ 150 max Unit 150 µA Condition mA 120 120 145 145 120 120 145 145 120 138 145 165 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic min typ 25°C max min typ 700 900 600 600 800 800 85°C max min typ 700 900 600 600 800 800 fSHIFT Max. Shift Frequency 700 900 tPLH tPHL Propagation Delay to Output Clk MR 600 600 800 800 ts Setup Time D SEL 50 300 –100 150 50 300 –100 150 50 300 –100 150 Hold Time D SEL 300 75 100 –150 300 75 100 –150 300 75 100 –150 tRR Reset Recovery Time 900 700 900 700 900 700 tPW Minimum Pulse Width Clk, MR 400 th tSKEW Within-Device Skew tr tf Rise/Fall Times 20 - 80% max Unit Condition MH z ps 1000 1000 1000 1000 1000 1000 ps ps ps ps 400 75 400 75 75 ps Note 1 ps 300 525 800 300 525 800 300 525 800 1. Within-device skew is defined as identical transitions on similar paths through a device. MOTOROLA 2–2 ECLinPS and ECLinPS Lite DL140 — Rev 4 MC10E142 MC100E142 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776–02 ISSUE D 0.007 (0.180) B Y BRK -N- T L –M M U 0.007 (0.180) X G1 M S N T L –M S S N S D Z -L- -M- D W 28 V 1 C A 0.007 (0.180) M R 0.007 (0.180) M T L –M S T L –M S N S N S H S N S 0.007 (0.180) M T L –M N S S 0.004 (0.100) G J -T- K SEATING PLANE F VIEW S G1 T L –M S N 0.007 (0.180) M T L –M S N S VIEW S S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). ECLinPS and ECLinPS Lite DL140 — Rev 4 T L –M K1 E S S VIEW D-D Z 0.010 (0.250) 0.010 (0.250) 2–3 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 — 0.025 — 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 — 0.020 2° 10° 0.410 0.430 0.040 — MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 — 0.64 — 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 — 0.50 2° 10° 10.42 10.92 1.02 — MOTOROLA MC10E142 MC100E142 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–4 *MC10E142/D* MC10E142/D ECLinPS and ECLinPS Lite DL140 — Rev 4