Order this document by MPX200/D SEMICONDUCTOR TECHNICAL DATA The MPX200 series device is a silicon piezoresistive pressure sensors provide a very accurate and linear voltage output — directly proportional to the applied pressure. This standard, low cost, uncompensated sensor permits manufacturers to design and add their own external temperature compensating and signal conditioning networks. Compensation techniques are simplified because of the predictability of Motorola’s single element strain gauge design. Features 0 to 200 kPa (0 – 29 psi) 60 mV FULL SCALE SPAN (TYPICAL) • Low Cost • Patented Silicon Shear Stress Strain Gauge • ± 0.25% (Max) Linearity • Full Scale Span 60 mV (Typ) BASIC CHIP CARRIER ELEMENT CASE 344–15, STYLE 1 • Easy to Use Chip Carrier Package Options • Ratiometric to Supply Voltage • Absolute, Differential and Gauge Options Application Examples • Pump/Motor Controllers • Robotics • Level Indicators • Medical Diagnostics • Pressure Switching • Barometers DIFFERENTIAL PORT OPTION CASE 344C–01, STYLE 1 • Altimeters Figure 1 illustrates a schematic of the internal circuitry on the stand–alone pressure sensor chip. PIN 3 NOTE: Pin 1 is the notched pin. + VS PIN NUMBER PIN 2 + Vout X–ducer 1 Gnd 3 VS 2 +Vout 4 –Vout PIN 4 – Vout PIN 1 Figure 1. Uncompensated Pressure Sensor Schematic VOLTAGE OUTPUT versus APPLIED DIFFERENTIAL PRESSURE The differential voltage output of the X–ducer is directly proportional to the differential pressure applied. The absolute sensor has a built–in reference vacuum. The output voltage will decrease as vacuum, relative to ambient, is drawn on the pressure (P1) side. The output voltage of the differential or gauge sensor increases with increasing pressure applied to the pressure (P1) side relative to the vacuum (P2) side. Similarly, output voltage increases as increasing vacuum is applied to the vacuum (P2) side relative to the pressure (P1) side. Senseon and X–ducer are trademarks of Motorola, Inc. REV 7 Motorola Sensor Device Data Motorola, Inc. 1997 1 MAXIMUM RATINGS Rating Symbol Value Unit Overpressure(8) (P1 > P2) Pmax 400 kPa Burst Pressure(8) (P1 > P2) Pburst 2000 kPa Tstg – 40 to +125 °C TA – 40 to +125 °C Storage Temperature Operating Temperature OPERATING CHARACTERISTICS (VS = 3.0 Vdc, TA = 25°C unless otherwise noted, P1 > P2) Characteristic Symbol Min Typ Max Unit Pressure Range(1) POP 0 — 200 kPa Supply Voltage(2) VS — 3.0 6.0 Vdc Supply Current Io — 6.0 — mAdc VFSS 45 60 90 mV Full Scale Span(3) Offset(4) Voff 0 20 35 mV Sensitivity ∆V/∆P — 0.3 — mV/kPa Linearity(5) — – 0.25 — 0.25 %VFSS Pressure Hysteresis(5) (0 to 200 kPa) — — ± 0.1 — %VFSS Temperature Hysteresis(5) (– 40°C to +125°C) — — ± 0.5 — %VFSS Temperature Coefficient of Full Scale Span(5) TCVFSS – 0.22 — – 0.16 %VFSS/°C TCVoff — ±15 — µV/°C TCR 0.21 — 0.27 %Zin/°C Temperature Coefficient of Offset(5) Temperature Coefficient of Resistance(5) Zin 400 — 550 Ω Zout 750 — 1800 Ω Response Time(6) (10% to 90%) tR — 1.0 — ms Warm–Up — — 20 — ms Offset Stability(9) — — ± 0.5 — %VFSS Symbol Min Typ Max Unit Weight (Basic Element Case 344–15) — — 2.0 — Grams Common Mode Line Pressure(7) — — — 690 kPa Input Impedance Output Impedance MECHANICAL CHARACTERISTICS Characteristic NOTES: 1. 1.0 kPa (kiloPascal) equals 0.145 psi. 2. Device is ratiometric within this specified excitation range. Operating the device above the specified excitation range may induce additional error due to device self–heating. 3. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the minimum rated pressure. 4. Offset (Voff) is defined as the output voltage at the minimum rated pressure. 5. Accuracy (error budget) consists of the following: • Linearity: Output deviation from a straight line relationship with pressure, using end point method, over the specified pressure range. • Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied. • Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure, at 25°C. • TcSpan: Output deviation at full rated pressure over the temperature range of 0 to 85°C, relative to 25°C. • TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 0 to 85°C, relative to 25°C. • TCR: Zin deviation with minimum rated pressure applied, over the temperature range of – 40°C to +125°C, relative to 25°C. 6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to a specified step change in pressure. 7. Common mode pressures beyond specified may result in leakage at the case–to–lead interface. 8. Exposure beyond these limits may cause permanent damage or degradation to the device. 9. Offset stability is the product’s output deviation when subjected to 1000 hours of Pulsed Pressure, Temperature Cycling with Bias Test. 2 Motorola Sensor Device Data LINEARITY Linearity refers to how well a transducer’s output follows the equation: Vout = Voff + sensitivity x P over the operating pressure range (see Figure 2). There are two basic methods for calculating nonlinearity: (1) end point straight line fit or (2) a least squares best line fit. While a least squares fit gives the “best case” linearity error (lower numerical value), the calculations required are burdensome. Conversely, an end point fit will give the “worse case” error (often more desirable in error budget calculations) and the calculations are more straightforward for the user. Motorola’s specified pressure sensor linearities are based on the end point straight line method measured at the midrange pressure. TEMPERATURE COMPENSATION Figure 3 shows the typical output characteristics of the MPX200 series over temperature. The output is directly proportional to the pressure and is essentially a straight line. The X–ducer piezoresistive pressure sensor element is a semiconductor device which gives an electrical output signal proportional to the pressure applied to the device. This device uses a unique transverse voltage diffused semiconductor strain gauge which is sensitive to stresses produced in a thin silicon diaphragm by the applied pressure. Because this strain gauge is an integral part of the silicon diaphragm, there are no temperature effects due to differences in the thermal expansion of the strain gauge and the diaphragm, as are often encountered in bonded strain gauge pressure sensors. However, the properties of the strain gauge itself are temperature dependent, requiring that the device be temperature compensated if it is to be used over an extensive temperature range. Temperature compensation and offset calibration can be achieved rather simply with additional resistive components or by designing your system using the MPX2200 series sensors. Several approaches to external temperature compensation over both – 40 to +125°C and 0 to + 80°C ranges are presented in Motorola Applications Note AN840. 70 LINEARITY 60 70 60 ACTUAL 40 SPAN (VFSS) 30 THEORETICAL 20 10 0 MAX POP PRESSURE (kPA) WIRE BOND DIFFERENTIAL/GAUGE STAINLESS STEEL DIE METAL COVER P1 EPOXY CASE ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ LEAD FRAME DIFFERENTIAL/GAUGE ELEMENT P2 – 40°C 50 +25°C SPAN RANGE (TYP) +125°C 40 30 DIE BOND OFFSET (TYP) 10 0 0 PSI kPa Figure 2. Linearity Specification Comparison SILICONE GEL DIE COAT VS = 3.0 Vdc P1 > P2 20 OFFSET (VOFF) 0 OUTPUT (mVdc) OUTPUT (mVdc) 50 4.0 8.0 12 16 20 24 28 30 20 40 60 80 100 120 140 160 180 200 PRESSURE DIFFERENTIAL Figure 3. Output versus Pressure Differential SILICONE GEL ABSOLUTE DIE COAT DIE P1 WIRE BOND STAINLESS STEEL METAL COVER EPOXY CASE ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ LEAD FRAME ABSOLUTE ELEMENT P2 DIE BOND Figure 4. Cross–Sectional Diagrams (Not to Scale) Figure 4 illustrates the absolute sensing configuration (right) and the differential or gauge configuration in the basic chip carrier (Case 344–15). A silicone gel isolates the die surface and wire bond from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MPX200 series pressure sensor operating Motorola Sensor Device Data characteristics and internal reliability and qualification tests are based on use of dry air as the pressure media. Media other than dry air may have adverse effects on sensor performance and long term reliability. Contact the factory for information regarding media compatibility in your application. 3 PRESSURE (P1)/VACUUM (P2) SIDE IDENTIFICATION TABLE Motorola designates the two sides of the pressure sensor as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing the silicone gel which isolates the die from the environment. The differential or gauge sensor is designed to operate with positive differenPart Number tial pressure applied, P1 > P2. The absolute sensor is designed for vacuum applied to P1 side. The Pressure (P1) side may be identified by using the table below: Case Type Pressure (P1) Side Identifier MPX200A, MPX200D 344–15C Stainless Steel Cap MPX200DP 344C–01 Side with Part Marking MPX200AP, MPX200GP 344B–01 Side with Port Attached MPX200GVP 344D–01 Stainless Steel Cap MPX200AS, MPX200GS 344E–01 Side with Port Attached MPX200GSX 344F–01 Side with Port Attached MPX200GVSX 344G–01 Stainless Steel Cap ORDERING INFORMATION MPX200 series pressure sensors are available in absolute, differential and gauge configurations. Devices are available in the basic element package or with pressure port fittings which provide printed circuit board mounting ease and barbed hose pressure connections. MPX Series D i T Device Type O i Options C Case Type T Order Number Device Marking Basic Element Absolute, Differential Case 344–15 MPX200A MPX200D MPX200A MPX200D Ported Elements Differential Case 344C–01 MPX200DP MPX200DP Absolute, Gauge Case 344B–01 MPX200AP MPX200GP MPX200AP MPX200GP Gauge Vacuum Case 344D–01 MPX200GVP MPX200GVP Absolute, Gauge Stove Pipe Case 344E–01 MPX200AS MPX200GS MPX200A MPX200D Gauge Axial Case 344F–01 MPX200ASX MPX200GSX MPX200A MPX200D Gauge Vacuum Axial Case 344G–01 MPX200GVSX MPX200D 4 Motorola Sensor Device Data PACKAGE DIMENSIONS NOTES: C 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION –A– IS INCLUSIVE OF THE MOLD STOP RING. MOLD STOP RING NOT TO EXCEED 16.00 (0.630). POSITIVE PRESSURE (P1) R M B –A– DIM A B C D F G J L M N R N 1 PIN 1 2 3 L 4 –T– SEATING PLANE J POSITIVE PRESSURE (P1) G F D 4 PL 0.136 (0.005) T A M M INCHES MIN MAX 0.595 0.630 0.514 0.534 0.200 0.220 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.695 0.725 30_ NOM 0.475 0.495 0.430 0.450 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 15.11 16.00 13.06 13.56 5.08 5.59 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.40 17.65 18.42 30_ NOM 12.07 12.57 10.92 11.43 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344–15 ISSUE W SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5, 1982. 2. CONTROLLING DIMENSION: INCH. –A– –T– U L R H N PORT #1 POSITIVE PRESSURE (P1) –Q– B 1 2 3 4 PIN 1 K –P– 0.25 (0.010) J M T Q S S F C G D 4 PL 0.13 (0.005) M T S S Q S DIM A B C D F G H J K L N P Q R S U INCHES MIN MAX 1.145 1.175 0.685 0.715 0.305 0.325 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.159 0.230 0.250 0.220 0.240 0.910 BSC STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 7.75 8.26 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 5.84 6.35 5.59 6.10 23.11 BSC GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344B–01 ISSUE B Motorola Sensor Device Data 5 PACKAGE DIMENSIONS — CONTINUED PORT #1 R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. –A– U V W L H PORT #2 PORT #1 POSITIVE PRESSURE (P1) PORT #2 VACUUM (P2) N –Q– B SEATING PLANE SEATING PLANE 1 2 3 4 PIN 1 K –P– –T– –T– 0.25 (0.010) T Q M S S F J G D 4 PL C 0.13 (0.005) M T S S Q S DIM A B C D F G H J K L N P Q R S U V W INCHES MIN MAX 1.145 1.175 0.685 0.715 0.405 0.435 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.159 0.063 0.083 0.220 0.240 0.910 BSC 0.248 0.278 0.310 0.330 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 10.29 11.05 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 1.60 2.11 5.59 6.10 23.11 BSC 6.30 7.06 7.87 8.38 GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344C–01 ISSUE B NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5, 1982. 2. CONTROLLING DIMENSION: INCH. –A– U L SEATING PLANE –T– R DIM A B C D F G H J K L N P Q R S U H PORT #2 VACUUM (P2) POSITIVE PRESSURE (P1) N –Q– B 1 2 3 4 K PIN 1 S C J F –P– 0.25 (0.010) M T Q S G D 4 PL 0.13 (0.005) M T S S Q S INCHES MIN MAX 1.145 1.175 0.685 0.715 0.305 0.325 0.016 0.020 0.048 0.064 0.100 BSC 0.182 0.194 0.014 0.016 0.695 0.725 0.290 0.300 0.420 0.440 0.153 0.159 0.153 0.158 0.230 0.250 0.220 0.240 0.910 BSC STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 29.08 29.85 17.40 18.16 7.75 8.26 0.41 0.51 1.22 1.63 2.54 BSC 4.62 4.93 0.36 0.41 17.65 18.42 7.37 7.62 10.67 11.18 3.89 4.04 3.89 4.04 5.84 6.35 5.59 6.10 23.11 BSC GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344D–01 ISSUE B 6 Motorola Sensor Device Data PACKAGE DIMENSIONS — CONTINUED PORT #1 POSITIVE PRESSURE (P1) –B– C NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. A BACK SIDE VACUUM (P2) DIM A B C D F G J K N R S V V 4 3 2 1 PIN 1 K J N MILLIMETERS MIN MAX 17.53 18.28 6.22 6.48 19.81 20.82 0.41 0.51 1.22 1.63 2.54 BSC 0.36 0.41 8.76 9.53 7.62 7.87 4.52 4.72 5.59 6.10 4.62 4.93 G STYLE 1: PIN 1. 2. 3. 4. F R SEATING PLANE S INCHES MIN MAX 0.690 0.720 0.245 0.255 0.780 0.820 0.016 0.020 0.048 0.064 0.100 BSC 0.014 0.016 0.345 0.375 0.300 0.310 0.178 0.186 0.220 0.240 0.182 0.194 D 4 PL 0.13 (0.005) –T– M T B M GROUND + OUTPUT + SUPPLY – OUTPUT CASE 344E–01 ISSUE B –T– C A E –Q– U N V B R PORT #1 POSITIVE PRESSURE (P1) PIN 1 –P– 0.25 (0.010) M T Q M 4 3 2 1 S K J F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K N P Q R S U V INCHES MIN MAX 1.080 1.120 0.740 0.760 0.630 0.650 0.016 0.020 0.160 0.180 0.048 0.064 0.100 BSC 0.014 0.016 0.220 0.240 0.070 0.080 0.150 0.160 0.150 0.160 0.440 0.460 0.695 0.725 0.840 0.860 0.182 0.194 MILLIMETERS MIN MAX 27.43 28.45 18.80 19.30 16.00 16.51 0.41 0.51 4.06 4.57 1.22 1.63 2.54 BSC 0.36 0.41 5.59 6.10 1.78 2.03 3.81 4.06 3.81 4.06 11.18 11.68 17.65 18.42 21.34 21.84 4.62 4.92 G D 4 PL 0.13 (0.005) M T P S Q S STYLE 1: PIN 1. 2. 3. 4. GROUND V (+) OUT V SUPPLY V (–) OUT CASE 344F–01 ISSUE B Motorola Sensor Device Data 7 PACKAGE DIMENSIONS — CONTINUED –T– C A E –Q– U POSITIVE PRESSURE (P1) N V B R PIN 1 PORT #2 VACUUM (P2) –P– 0.25 (0.010) M T Q M 1 2 3 4 S K F J G D 4 PL 0.13 (0.005) M T P S Q S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K N P Q R S U V INCHES MIN MAX 1.080 1.120 0.740 0.760 0.630 0.650 0.016 0.020 0.160 0.180 0.048 0.064 0.100 BSC 0.014 0.016 0.220 0.240 0.070 0.080 0.150 0.160 0.150 0.160 0.440 0.460 0.695 0.725 0.840 0.860 0.182 0.194 STYLE 1: PIN 1. 2. 3. 4. MILLIMETERS MIN MAX 27.43 28.45 18.80 19.30 16.00 16.51 0.41 0.51 4.06 4.57 1.22 1.63 2.54 BSC 0.36 0.41 5.59 6.10 1.78 2.03 3.81 4.06 3.81 4.06 11.18 11.68 17.65 18.42 21.34 21.84 4.62 4.92 GROUND V (+) OUT V SUPPLY V (–) OUT CASE 344G–01 ISSUE B Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET: http://motorola.com/sps 8 ◊ MPX200/D Motorola Sensor Device Data