74ACT541 OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 4 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 8 µA (MAX.) at TA = 25 oC COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN), VIL = 0.8V (MAX) 50Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 541 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The ACT541 is an advanced CMOS OCTAL BUS BUFFER (3-STATE) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology.It is ideal for low power applications mantaining high speed operation similar to eqivalent Bipolar Schottky TTL. The 3 STATE control gate operates as a two B M (Plastic Package) (Micro Package) ORDER CODES : 74ACT541B 74ACT541M input AND such that if either G1 and G2 are high, all eight outputs are in the high impedance state. In order to enhance PC board layout, the AC541 offers a pinout having inputs and outputs on opposite sides of the package. The device is designed to interface directly High Speed CMOS systems with TTL, NMOS and CMOS output voltage levels. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS December 1998 1/8 74ACT541 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1,19 G1, G2 Output Enable Input NAME AND FUNCT ION 2, 3, 4,5, 6, 7,8, 9 A1 to A8 Data Inputs 18, 17, 16, 15, 14, 13, 12, 11 Y1 to Y8 Data Outputs 10 GND Ground (0V) 20 VCC Positive Supply Voltage TRUTH TABLE INPUT O UT PUT G1 G2 An Yn H X X Z X H X Z L L H H L L L L X:”H” or ”L” Z: High impedance ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V V VI DC Input Voltage -0.5 to VCC + 0.5 VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 50 mA ± 400 mA ICC orIGND Tstg TL DC VCC or Ground Current Storage Temperature Lead Temperature (10 sec) -65 to +150 o 300 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Unit 4.5 to 5.5 V VI Input Voltage 0 to VCC V VO Output Voltage Top Operating Temperature: dt/dv Input Rise and Fall Time VCC = 4.5 to 5.5V (note 1) 1) VIN from 0.8 V to 2.0 V 2/8 Value Supply Voltage VCC 0 to VCC -40 to +85 8 V o C ns/V 74ACT541 DC SPECIFICATIONS Symb ol Parameter Test Co nditions VIH High Level Input Voltage 4.5 5.5 VIL Low Level Input Voltage 4.5 5.5 VOH High Level Output Voltage 4.5 5.5 Low Level Output Voltage VO = 0.1 V or VCC - 0.1 V Min. T yp. 2.0 1.5 2.0 2.0 1.5 2.0 VO = 0.1 V or VCC - 0.1 V VI(*) = VIH or VIL Un it -40 to 85 o C Max. Min. Max. V 1.5 0.8 0.8 1.5 0.8 0.8 IO=-50 µA 4.4 4.49 4.4 IO=-50 µA 5.4 5.49 5.4 IO=-24 mA 3.86 IO=-24 mA 4.86 4.5 IO=50 µA 0.001 0.1 0.1 IO=50 mA 0.001 0.1 0.1 IO=24 mA 0.36 0.44 IO=24 mA 0.36 0.44 5.5 4.5 5.5 (*) VI = VIH or VIL V V 5.5 4.5 VOL Valu e T A = 25 oC V CC (V) 3.76 4.76 V Input Leakage Current 5.5 VI = VCC orGND ±0.1 ±1 µA IOZ 3 State Output Leakage Current 5.5 VI = VIH orVIL VO = VCC orGND ±0.5 ±5 µA ICCT Max ICC /Input 5.5 VI = VCC -2.1V 1.5 mA ICC Quiescent Supply Current 5.5 VI = VCC orGND 40 µA IOLD Dynamic Output Current (note 1, 2) 5.5 VOLD = 1.65 V max 75 mA VOHD = 3.85 V min -75 mA II IOHD 0.6 4 1) Maximum test duration 2ms, one output loaded attime 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 50 Ω. AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, RL = 500 Ω, Input tr = tf =3 ns) Symb ol Parameter T est Con ditio n V CC (V) tPLH tPHL tPZL tPZH tPLZ tPHZ Valu e Un it T A = 25 oC -40 to 85 o C Min. T yp. Max. Min. Max. 1.5 5 6.5 1.5 7.15 Propagation Delay Time 5.0(*) Output Enable Time 5.0(*) 1.5 6 7.8 1.5 8.5 (*) 1.5 6 7.8 1.5 8.5 Output Disable Time 5.0 ns ns ns (*) Voltage range is 5V ± 0.5V CAPACITIVE CHARACTERISTICS Symbo l Parameter Test Con dition s V CC (V) Value T A = 25 o C Min. T yp. Max. Unit -40 to 85 o C Min. Max. CIN Input Capacitance 5.0 4 pF CPD Power Dissipation Capacitance (note 1) 5.0 22 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/8 (per circuit) 3/8 74ACT541 TEST CIRCUIT T EST tPLH , tPHL SW IT CH Open tPZL , tPLZ 2VCC tPZH , tPHZ Open CL = 50 pF or equivalent (includes jigand probe capacitance) RL = R1 = 500Ω orequivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 4/8 74ACT541 WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 5/8 74ACT541 Plastic DIP-20 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.254 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.053 P001J 6/8 74ACT541 SO-20 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 2.65 0.10 0.104 0.20 a2 MAX. 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45 (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 M S 0.75 0.029 8 (max.) P013L 7/8 74ACT541 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 1998 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 8/8