MIG400J101H TOSHIBA Intelligent Power Module Silicon N Channel IGBT MIG400J101H High Power Switching Applications Motor Control Applications l Integrates inverter power circuits & control circuits (IGBT drive units, protection units for over-current, under-voltage & over temperature) in one package. l The electrodes are isolated from case. l High speed type IGBT : VCE (sat) = 2.5V (max) toff = 2.0µs (max) trr = 0.15µs (max) l Package dimensions : TOSHIBA 2-121A1A l Weight : 510g Equivalent Circuit 1 2002-12-06 MIG400J101H Maximum Ratings (Tj = 25°C) Stage Characteristic Condition Supply voltage Symbol Ratings Unit P-N power terminal VCC 450 V ― VCES 600 V IC 400 A Collector-emitter voltage Inverter Collector current Tc = 25°C, DC Forward current Tc = 25°C, DC IF 400 A Collector power dissipation Tc = 25°C PC 1600 W Tj 150 °C Junction temperature Control Module ― Control supply voltage VD-GND terminal VD 20 V Input voltage IN-GND terminal VIN 20 V Fault output voltage FO-GND (L) terminal VFO 20 V Fault output current FO sink current IFO 14 mA Operating temperature ― TC −20 ~ +100 °C Storage temperature range ― Tstg −40 ~ +125 °C VISO 2500 V ― 3 Nm Isolation voltage AC 1 minute, Screw torque M6 Electrical Characteristics (Tj = 25°C) a. Inverter Stage Characteristic Collector cut-off current Collector-emitter saturation voltage Forward voltage Symbol ICEX VCE (sat) VF Test Condition VCE = 600V VD = 15V, IC = 400A VIN = 3V → 0V Min Typ. Max Tj = 25°C ― ― 2 Tj = 125°C ― ― 40 Tj = 25°C ― 2.0 2.5 Tj = 125°C ― 2.0 ― ― 2.1 2.7 1.4 2.1 2.8 ― 1.2 1.8 ― 0.08 0.15 ― 1.2 2.0 ― 0.3 0.6 IF = 400A ton tc (on) Switching time trr VCC = 300V, IC = 400A VD = 15V, VIN = 3V ↔ 0V Inductive load (Note 1) toff tc (off) 2 Unit mA V V µs 2002-12-06 MIG400J101H b. Control Stage (Tj = 25°C) Characteristic Symbol Control circuit current ID Input on signal voltage VIN (on) Fault output current Protection IFO (on) Normal IFO (off) Test Condition Min Typ. Max Unit VD = 15V ― 20 30 mA VD = 15V, IC = 400mA 0.9 1.1 1.3 V 8 10 12 ― ― 1 VD = 15V mA Over current protection trip level OC VD = 15V, Tj = 125°C 560 640 ― A Short circuit protection trip level SC VD = 15V, Tj = 125°C 840 960 ― A ― 10 ― µs 111 118 125 93 100 107 11.3 12.0 12.7 11.8 12.5 13.2 1 2 3 ms MIN TYP. MAX Unit IGBT ― ― 0.078 FRD ― ― 0.208 Compound is applied ― 0.05 ― Over current cut-off time toff (OC) Over temperature protection Trip level OT Reset level OTr Control supply under voltage protection Trip level UV Reset level UVr Fault output pulse width c. tFO VD = 15V Case temperature ― VD = 15V °C V Thermal Resistance (Tj = 25°C) Characteristic Symbol Junction to case thermal resistance Rth (j-c) Case to fin thermal resistance Rth (c-f) Test Condition 3 °C / W °C / W 2002-12-06 MIG400J101H Note 1: Switching time test circuit & timing chart 4 2002-12-06 MIG400J101H 5 2002-12-06 MIG400J101H 6 2002-12-06 MIG400J101H Package Dimensions: TOSHIBA 2-121A1A Unit: mm 7 2002-12-06 MIG400J101H RESTRICTIONS ON PRODUCT USE 000707EAA · TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. · The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. · The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 8 2002-12-06