SANYO LC88F5LA4ACS

Ordering number : ENA1860
LC88F5LA4ACS
CMOS IC
FROM 96K byte, RAM 6K byte on-chip
16-bit 1-chip Microcontroller
Overview
The SANYO LC88F5LA4ACS is a 16-bit microcomputer that, centered around an Xstromy16 CPU, integrates on a single
chip a number of hardware features such as 96K-byte flash ROM (onboard programmable), 6K-byte RAM, six 16-bit
timers, a base timer serving as a time-of-day clock, a real time clock, two synchronous SIO interfaces with automatic
transmission capability, a single master I2C/synchronous SIO interface, a slave I2C/synchronous SIO interface, two
asynchronous SIO (UART) interfaces, a 4-channel 12-bit resolution AD converter, a watchdog timer, a system clock
frequency divider, a 38-source (24 modules) 13-vector interrupt feature, and on-chip debugger feature.
Features
„Xstromy16 CPU
• 4G-byte address space
• General-purpose registers: 16 bits × 16registers
„Flash ROM
• Capable of onboard programming with a wide range of voltage levels (2.6 to 3.6V).
• Block-erasable in 128 or 1K byte units.
• Data written in 2-byte units.
• 98304 × 8 bits
„RAM
• 6144 × 8 bits
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by
SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
Ver.1.00
30211HKIM 20100223-S00001 No.A1860-1/33
LC88F5LA4ACS
„Minimum instruction cycle time (tCYC)
• 100ns (10MHz)
VDD = 2.6 to 3.6V
• 250ns (4MHz)
VDD = 2.2 to 3.6V
„Ports
● Normal withstand voltage I/O ports
Ports whose I/O direction can be designated in 1 bit units
● Oscillation/normal withstand voltage I/O ports
● Oscillation pins
● Reset pins
● TEST pins
● Power pins
: 33 (P0n P1n, P20 to P25, P3n, P60 to P62)
: 2 (PC0, PC1)
: 2 (CF1, CF2)
: 1 (RESB)
: 1 (TEST)
: 7 (VSS1 to 2, VSSA, VDD1 to 3, VDDA)
„Timers
• Timer 0: 16-bit timer that supports PWM/toggle outputs
1) 5-bit prescaler
2) 8-bit PWM × 2, 8-bit timer + 8-bit PWM mode selectable
3) Clock source selectable from system clock, OSC0, OSC1, and internal RC oscillator
• Timer 1: 16-bit timer with capture registers
1) 5-bit prescaler
2) May be divided into 2 channels of 8-bit timer
3) Clock source selectable from system clock, OSC0, OSC1, and internal RC oscillator
• Timer 2: 16-bit timer with capture registers
1) 4-bit prescaler
2) May be divided into 2 channels of 8-bit timer
3) Clock source selectable from system clock, OSC0, OSC1, and external events
• Timer 3: 16-bit timer that supports PWM/toggle outputs
1) 8-bit prescaler
2) 8-bit timer × 2ch or 8-bit timer + 8-bit PWM mode selectable
3) Clock source selectable from system clock, OSC0, OSC1, and external events
• Timer 4: 16-bit timer that supports toggle outputs
1) Clock source selectable from system clock and prescaler 0
• Timer 5: 16-bit timer that supports toggle outputs
1) Clock source selectable from system clock and prescaler 0
* Prescaler 0 and 1 are consisted of 4 bits and can choose their clock source from OSC0 or OSC1.
• Base timer
1) Clock may be selected from OSC0 (32.768kHz crystal oscillator) and frequency-divided output of system clock.
2) Interrupts can be generated in 7 timing schemes.
„Real time clock
1) Calender with Jan. 1, 2000 to Dec.31, 2799 including automatic leap year calculation function.
2) Consisted of Independent second- minute-hour-day-month-year-century counters.
3) Programmable count-clock calibration function.
No.A1860-2/33
LC88F5LA4ACS
„Serial interfaces
• SIO0: 8-bit synchronous SIO
1) LSB first/MSB first mode selectable
2) Supports data communication with a data length of 8 bits or less (1 to 8 bits specifiable)
3) Built-in 8-bit baudrate generator (4 tCYC to 512 tCYC transfer clocks)
4) Continuous/automatic data transmission (9- to 32768-bit units specifiable)
5) Interval function (intervals specifiable in 0 to 64 tSCK units)
6) Wakeup function
• SIO1: 8-bit synchronous SIO
1) LSB first/MSB first mode selectable
2) Supports data communication with a data length of 8 bits or less (1 to 8 bits specifiable)
3) Built-in 8-bit baudrate generator (4 tCYC to 512 tCYC transfer clocks)
4) Continuous/automatic data transmission (9- to 32768-bit units specifiable)
5) Interval function (intervals specifiable in 0 to 64 tSCK units)
6) Wakeup function
• SMIIC0: Single master I2C/8-bit synchronous SIO
Mode 0: Single-master mode communication
Mode 1: Synchronous 8-bit serial I/O (MSB first)
• SLIIC0: Slave I2C/8-bit synchronous SIO
Mode 0: I2C slave mode communication
Mode 1: Synchronous 8-bit serial I/O (MSB first)
Note: usable only with the external clock source
• UART0
1) Data length
: 8 bits (LSB first)
2) Start bits
: 1 bit
3) Stop bits
: 1 bit
4) Parity bits
: None/even parity/odd parity
5) Transfer rate
: 4/8 cycle
6) Baudrate source clock : P07 input signal used as a 1 cycle signal (T0PWMH can be used as a clock source) or
Timer 4 cycle.
7) Full duplex communication
Note: The “cycle” refers to one period of the baudrate clock source.
• UART2
1) Data length
: 8 bits (LSB first)
2) Start bits
: 1 bit
3) Stop bits
: 1/2 bit
4) Parity bits
: None/even parity/odd parity
5) Transfer rate
: 8 to 4096 cycle
6) Baudrate source clock : System clock/OSC0/OSC1/P25 input signal
7) Wakeup function
8) Full duplex communication
Note: The “cycle” refers to one period of the baudrate clock source.
No.A1860-3/33
LC88F5LA4ACS
„AD converter
1) 12/8 bits resolution selectable
2) Analog input: 14 channels
3) Comparator mode
„Watchdog timer
1) Driven by the base timer + internal watchdog timer dedicated counter
2) Interrupt or reset mode selectable
„Interrupts (peripheral function)
• 38 sources (24 modules), 13 vector addresses
1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of
the level equal to or lower than the current interrupt are not accepted.
2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level
takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector
address takes precedence.
No.
Vector Address
Module
1
08000H
Watchdog timer (1)
2
08004H
Base timer (2)
3
08008H
Timer 0 (2)
4
0800CH
INT0 (1)
5
08014H
INT1 (1)
6
08018H
INT2 (1)/timer 1 (2)/UART2 (4)
7
0801CH
INT3 (1)/timer 2 (4)/SMIIC0 (1)/SLIIC1 (1)
8
08020H
INT4 (1)/timer 3 (2)
9
08024H
INT5 (1)/timer 4 (1)/SIO1 (2)
10
08030H
ADC (1)/timer 5 (1)
11
08034H
INT6 (1)
12
08038H
INT7 (1)/SIO0 (2)/SIO0(2)
13
0803CH
Port 0 (3)/RTC (1)
• 3 priority levels selectable.
• Of interrupts of the same level, the one with the smallest vector address takes precedence.
• A number enclosed in parentheses denotes the number of sources.
„Subroutine Stack: 6K-byte RAM area
• Subroutine calls that automatically save PSW, interrupt vector calls: 6 bytes
• Subroutine calls that do not automatically save PSW: 4 bytes
„Multiplication/division instructions
• 16 bits × 16 bits (18 tCYC execution time)
• 16 bits ÷ 16 bits (18 to 19 tCYC execution time)
• 32 bits ÷ 16 bits (18 to 19 tCYC execution time)
„Oscillator circuits
• RC oscillator circuit (internal): For system clock
• CF oscillator circuit (built-in Rf circuit): For system clock (OSC1)
• VMRC oscillator circuit: For system clock (OSC1)
• Crystal oscillator circuit (built-in Rf circuit): For low-speed system clock (OSC0)
• SLRC oscillator circuit (internal): For system clock (In the case of exception processing)
„System clock divider function
• Can run on low current.
• 1/1 to 1/128 of the system clock frequency can be set.
No.A1860-4/33
LC88F5LA4ACS
„Standby Function
• HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
1) Oscillation is not halted automatically.
2) Released by a system reset or occurrence of an interrupt.
• HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) OSC1, RC and OSC0 oscillators automatically stop.
2) There are the six ways of releasing the HOLD mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, INT2, INT3, INT4, INT5, INT6, and INT7 pins to the specified level
(3) Having an interrupt source established at port 0
(4) Having an interrupt established at SIO0 or SIO1
(5) Having an interrupt established at UART2
• HOLDX mode: Suspends instruction execution and the operation of the peripheral circuits except those which run
on OSC0.
1) OSC1 and RC oscillations automatically stop.
2) OSC0 maintains the state that is established when the HOLDX mode is entered.
3) There are seven ways of releasing the HOLDX mode.
(1) Setting the reset pin to the low level
(2) Setting at least one of the INT0, INT1, INT2, INT3, INT4, INT5, INT6, and INT7 pins to the specified level
(3) Having an interrupt source established at port 0
(4) Having an interrupt source established at the base timer circuit
(5) Having an interrupt established at SIO0 or SIO1
(6) Having an interrupt established at UART2
.
„On-chip debugger function
• Supports software debugging with the IC mounted on the target board.
• Supports source line debugging and tracing functions, and breakpoint setting and real time display.
• Single-wire communication
„Power supply voltage
• VDD1, 2
: 2.2 to 3.6V.
• VDD3
: (I/O) 1.6 to 3.6V.
* Voltage of VDD3 must be lower than VDD1.
„Package Form
• WLP46 (3.03 × 3.03): Lead-free and halogen-free type
„Development Tools
• On-chip debugger: EOCUIF1 + LC88F5LA4A
No.A1860-5/33
LC88F5LA4ACS
Package Dimensions
unit : mm (typ)
3404
BOTTOM VIEW
SIDE VIEW
0.315
TOP VIEW
0.315
1 2 3 4 5 6 7
0.4
0.4
3.03
3.03
0.68 MAX
G F E D C B A
0.2
SIDE VIEW
0.26
SANYO : WLP46(3.03X3.03)
Pin Assignment
Top view
Bottom view
7
6
5
LC88F5LA4ACS
4
3
2
1
G
F
E
D
C
B
A
SANYO: WLP46 (3.03×3.03) (Lead-free and halogen-free type)
No.A1860-6/33
LC88F5LA4ACS
No.
Name
No.
Name
P04/P04INT
No.
F7
Name
G1
TEST
B4
P12/SCK0
E2
RESB
D3
P05/P05INT
F6
P13/U0TX
F1
VSSA
A5
P06/T0PWML
G7
P14/T3OL/U0RX/INT2
E1
VSS1
B5
P07/T0PWMH/U0BRG
E5
P15/T3OH/INT3
D2
PC0/XT1
A6
P37/T4O
G6
P16/U2RX
D1
PC1/XT2
C5
P36/SCK1
F5
P17/U2TX
C1
VDD1
A7
P35/SI1/SB1
G5
P62
C2
VDDA
B6
P34/SO1
F4
VDD3
B1
CF1
B7
P33/SM0DA
G4
P20/INT4
A1
CF2
C6
P32/SM0CK
E3
P21/INT5
B2
P00/P0INT/AN0
C7
P31/INT1/SM0DO
G3
P22/SL0CK
A2
P01/P0INT/AN1
D6
VDD2
F3
P23/SL0DA
B3
P60/AN2
D7
VSS2
G2
P24/SL0DO/INT6
A3
P61/AN3
D5
P30/INT0
F2
P25/INT7/T5O
C3
P02/P0INT
E7
P10/SO0
A4
P03/P0INT
E6
P11/SI0/SB0
No.A1860-7/33
LC88F5LA4ACS
System Block Diagram
CF
RC
X’tal
Clock generator
VMRC
Low
speed
RC
Base timer
Watchdog timer
FLASH ROM
Xstromy16
CPU
Timer 0
RAM
Timer 1
On-chip debugger
Timer 2
Port 0
Timer 3
Port 1
Timer 4
Port 2
Timer 5
Port 3
UART0
Port 6
UART2
Port C
SIO0
INT0 to INT7
SIO1
AD
SMIIC0
RTC
SLIIC0
No.A1860-8/33
LC88F5LA4ACS
Pin Description
Pin Name
I/O
Description
VSS1, VSS2
-
- Power supply
VSSA
-
- Power supply for AD
VDD1, VDD2
-
+ Power supply
VDD3
-
+ Power supply for port2’s I/O
VDDA
-
+ Power supply for AD
Port 0
I/O
• 8-bit I/O port
• I/O specifiable in 1-bit units
P00 to P07
• Pull-up resistors can be turned on and off in 1 bit units
• HOLD release input (P00 to P03, P04, P05)
• Port 0 interrupt input (P00 to P03, P04, P05)
• Pin functions
AN0 (P00) to AN1 (P01): AD converter input port
P06: Timer 0L output
P07: Timer 0L output/UART0 clock input
Port 1
I/O
• 8-bit I/O port
• I/O specifiable in 1-bit units
P10 to P17
• Pull-up resistors can be turned on and off in 1 bit units
• Pin functions
P10: SIO0 data output
P11: SIO0 data input/pulse input/output
P12: SIO0 clock input/output
P13: UART0 transmit
P14: Timer 3L output/UART0 receive/ INT2 input/HOLD release/timer 2 event input/timer 2L capture input
P15: Timer 3H output/ INT3 input/HOLD release/timer 2 event input/timer 2H capture input
P16: UART2 receive
P17: UART2 transmit
Interrupt acknowledge type
INT2, INT3: H level, L level, H edge, L edge, both edges
Port 2
I/O
• 6-bit I/O port
• I/O specifiable in 1-bit units
P20 to P25
• Pull-up resistors can be turned on and off in 1 bit units
• Pin functions
P20: INT4 input/HOLD release input/timer 3 event input/timer 2L capture input/timer 2H capture input
P21: INT5 input/HOLD release input/timer 3 event input/timer 2L capture input/timer 2H capture input
P22: SLIIC0 clock input/output
P23: SLIIC0 bus input/output/data input
P24: SLIIC0 data output (used in 3-wire SIO mode)/ INT6 input/HOLD release input
P25: Timer 5 output/ INT7 input/HOLD release input
Interrupt acknowledge type
INT4, INT5, INT6, INT7: H level, L level, H edge, L edge, both edges
Port 3
P30 to P37
I/O
• 8-bit I/O port
• I/O specifiable in 1-bit units
• Pull-up resistors can be turned on and off in 1 bit units
• Pin functions
P30: INT0 input/HOLD release/timer 2L capture input
P31: INT1 input/HOLD release/timer 2H capture input/SMIIC0 data output (used in 3-wire SIO mode)
P32: SMIIC0 clock input/output
P33: SMIIC0 bus input/output/data input
P34: SIO1 data output
P35: SIO1 data input/bus input/output
P36: SIO1 clock input/output
P37: Timer 4 output
Interrupt acknowledge type
INT0, INT1: H level, L level, H edge, L edge, both edges
Continued on next page.
No.A1860-9/33
LC88F5LA4ACS
Continued from preceding page.
Pin Name
Port 6
I/O
Description
• 3-bit I/O port
I/O
• I/O specifiable in 1-bit units
P60 to P62
• Pull-up resistors can be turned on and off in 1 bit units
• Pin functions
AN2 (P60) to AN3 (P61): AD converter input port
Port C
• 2-bit I/O port
I/O
• I/O specifiable in 1-bit units
PC0 to PC1
• Pin functions
PC0: 32.768kHz crystal oscillator input (XT1)
PC1: 32.768kHz crystal oscillator output (XT2)
TEST
• TEST pin
I/O
• Used to communicate with on-chip debugger.
• Connects an external 100kΩ pull-down resistor.
RESB
I
Reset pin
CF1
I
Ceramic resonator input pin
CF2
O
Ceramic resonator output pin
Port Output Types
The table below lists the types of port outputs and the presence/absence of a pull-up resistor.
Data can be read into any input port even if it is in the output mode.
Port Name
P00 to P07
Option Selected in
Output Type
Units of
Pull-up Resistor
CMOS
1 bit
Programmable
P60 to P62
P10 to P17
Able to program special functions’ output type from CMOS
P20 to P25
output or Nch-opendrain
P30 to P37
PC0
-
N-channel open drain (32.768kHz crystal oscillator input)
None
PC1
-
Nch-open drain (32.768kHz crystal oscillator output)
None
* Make the following connection to minimize the noise input to the VDD1 pin and prolong the backup time.
* Power supply must be VDD1 ≤ VDD3.
* Be sure to electrically short the VSS1, VSS2 and VSSA pins.
Example 1: When data is being backed up in the HOLD mode, the H level signals to the output ports are fed by the
backup capacitors.
LSI
VDD1
Power
supply
For Backup
VDDA
VDD2
Power
supply
VDD3
VSS1 VSS2 VSSA
No.A1860-10/33
LC88F5LA4ACS
Example 2: When data is being backed up in the HOLD mode, the H level output at any ports is not sustained and is
unpredictable.
LSI
VDD1
Power
supply
For backup
VDDA
VDD2
Power
supply
VDD3
VSS1 VSS2 VSSA
Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = VSSA = 0V
Parameter
Maximum supply
Symbol
Applicable Pin
/Remarks
VDD[V]
VDD max
VDD1, VDD2, VDDA
VDD1=VDD2=VDDA
VDD3 max
VDD3
VDD3≤VDD
VI(1)
CF1, RESB
voltage
Input voltage
Input/output
VIO(1)
voltage
Specification
Conditions
min
typ
-0.3
+4.0
-0.3
+4.0
-0.3
VDD
+0.3
-0.3
VDD
+0.3
-0.3
VDD3
+0.3
Ports 0, 1, 3
Port 6
PC0, PC1
VIO(2)
Peak output
IOPH (1)
current
IOPH (2)
Ports 2
VDD3≤VDD
P04 to P07, P62
CMOS output selected
Ports 1, 2, 3
Per applicable pin
P00 to P03
Per applicable pin
P60 to P61
High level output current
Average
IOMH (1)
output
current
IOMH (2)
(Note 1-1)
Total output
P04 to P07, P62
CMOS output selected
Ports 1, 2, 3
Per applicable pin
P00 to P03
Per applicable pin
P60 to P61
ΣIOAH (1)
current
ΣIOAH (2)
ΣIOAH (3)
ΣIOAH (4)
ΣIOAH (5)
P60 to P61
Total of currents at
P00 to P03
applicable pins
P04 to P07
Total of currents at
P31 to p37
applicable pins
Port 1
Total of currents at
P30, P62
applicable pins
P04 to P07, P62
Total of currents at
Ports 1, 3
applicable pins
Port 2
Total of currents at
applicable pins
max
unit
V
-7.5
-4.5
-5
-2.5
mA
-10
-15
-15
-30
-15
Note 1-1: Average output current refers to the average of output currents measured for a period of 100ms.
Continued on next page.
No.A1860-11/33
LC88F5LA4ACS
Continued from preceding page.
Parameter
Peak output
Symbol
IOPL(1)
current
Applicable Pin
/Remarks
P04 to P07, P62
Specification
Conditions
VDD[V]
min
typ
Per applicable pin
P00 to P03
unit
12.5
Ports 1, 2, 3
IOPL(2)
max
Per applicable pin
7.5
P60 to P61
PC0 to PC1
Average
IOML(1)
output current
Low level output current
(Note 1-1)
P04 to P07, P62
Per applicable pin
10
Port 1, 2, 3
IOML(2)
P00 to P03
Per applicable pin
5
P60 to P61
PC0 to PC1
Total output
ΣIOAL(1)
PC0 to PC1
current
Total of currents at
10
applicable pins
ΣIOAL(2)
ΣIOAL(3)
P60 to P61
Total of currents at
P00 to P03
applicable pins
P00 to P03
Total of currents at
P60 to P61
applicable pins
mA
10
15
PC0 to PC1
ΣIOAL(4)
ΣIOAL(5)
ΣIOAL(6)
Allowable power
Pd max
dissipation
P04 to P07
Total of currents at
P31 to P37
applicable pins
Ports 1, 2
Total of currents at
P30, P62
applicable pins
P04 to P07, P62
Total of currents at
Ports 1, 2, 3
applicable pins
WLP46 (3.03×3.03)
30
60
80
Ta=-40 to +85°C
With thermal resistance
T.B.D
mW
board (Note 1-2)
Operating ambient
Topr
temperature
Storage ambient
temperature
Tstg
-40
+85
-55
+125
°C
Note 1-1: Average output current refers to the average of output currents measured for a period of 100ms.
Note 1-2: Thermal resistance board is used.
No.A1860-12/33
LC88F5LA4ACS
Allowable Operating Conditions at Ta = -40°C to +85°C, VSS1 = VSS2 = VSSA = 0V
Parameter
Operating
Applicable
Symbol
VDD(1)
Pin/Remarks
VDD1=VDD2=VDDA
Specification
Conditions
VDD[V]
min
typ
max
unit
0.098μs≤tCYC≤66μs
2.6
3.6
0.245μs≤tCYC≤66μs
2.2
3.6
1.8
3.6
2.2 to 3.6
0.7VDD
VDD
2.2 to 3.6
0.75VDD
VDD
2.2 to 3.6
0.7VDD
VDD
2.2 to 3.6
0.7VDD3
VDD3
2.2 to 3.6
VSS
0.25VDD
2.2 to 3.6
VSS
0.25VDD
2.2 to 3.6
VSS
0.3VDD
2.2 to 3.6
VSS
0.3VDD3
2.6 to 3.6
0.098
66
2.2 to 3.6
0.245
66
2.6 to 3.6
0.1
10
2.2 to 3.6
0.1
4
2.6 to 3.6
0.2
20
2.2 to 3.6
0.2
8
supply voltage
(Note 2-1)
Memory
VHD
VDD1=VDD2=VDDA
sustaining
RAM and register contents
sustained in HOLD mode
supply voltage
High level input
VIH(1)
Ports 0, 1, 3, 6
voltage
VIH(2)
CF1, RESB
PC0, PC1
2
VIH(3)
P32, P33 I C side
VIH(4)
Port 2
Low level input
VIL(1)
Ports 0, 1, 3, 6
voltage
VIL(2)
CF1, RESB
VDD3= 1.6V to 3.6V
PC0, PC1
Instruction
VIL(3)
P32, P33 I2C side
VIL(4)
Port 2
VDD3= 1.6V to 3.6V
tCYC
V
μs
cycle time
(Note 2-2)
External
system clock
frequency
FEXCF(1)
CF1
• CF2 pin open
• System clock frequency
division ratio = 1/1
• External system clock
DUTY50±5%
• CF2 pin open
• System clock frequency
division ratio = 1/2
MHz
Note 2-1: VDD≥2.6V must be maintained when making onboard programming into flash ROM.
Note 2-2: Relationship between tCYC and oscillation frequency is 1/FmCF when frequency division ratio is 1/1 and
2/FmCF when the ratio is 1/2.
Continued on next page.
No.A1860-13/33
LC88F5LA4ACS
Continued from preceding page
Parameter
Oscillation
Symbol
FmCF(1)
Applicable
CF1, CF2
frequency
range
VDD[V]
10MHz ceramic oscillator mode
See Fig. 1.
FmCF(2)
CF1, CF2
(Note 2-3)
4MHz ceramic oscillator mode
See Fig. 1.
FmMRC(1)
Specification
Conditions
Pin /Remarks
min
typ
max
2.2 to 3.6
10
2.2 to 3.6
4
unit
Multivaliable RC oscillation
When SEL4M=0 center range
2.6 to 3.6
7.5
10
12.5
2.2 to 3.6
2
4
6
MHz
setting (Note 2-4)
FmMRC(2)
Multivaliable RC oscillation
When SEL4M=1 center range
setting (Note 2-4)
FmRC
Internal RC oscillation
2.2 to 3.6
0.5
1.0
2.0
FmSLRC
Internal low-speed RC oscillation
2.2 to 3.6
18
30
45
FsX'tal
XT1, XT2
32.768kHz crystal oscillator mode
See Fig. 2.
kHz
2.2 to 3.6
32.768
Note 2-3: See Tables 1 and 2 for oscillator constant values.
Note 2-4: To change to a multivaliable RC oscillation as a system clock, wait more than 20μs oscllation stabilizing time
after multivaliable RC oscillation is disabled to enabled.
No.A1860-14/33
LC88F5LA4ACS
Electrical Characteristics at Ta = -40 to +85°C, VSS1 = VSS2 = VSSA = 0V
Parameter
High level input
Symbol
IIH(1)
current
Applicable/
Specification
Conditions
Remarks
VDD[V]
Ports 0, 1, 3, 6
Output disabled
PC0, PC1
Pull-up resistor off
RESB
VIN=VDD
(including output Tr. off leakage
min
typ
max
2.2 to 3.6
1
2.2 to 3.6
15
2.2 to 3.6
1
unit
current)
IIH(2)
CF1
VIN=VDD
IIH(3)
Port 2
Output disabled
Pull-up resistor off
VIN=VDD3
VDD3= 1.6V to 3.6V
(including output Tr. off leakage
current)
Low level input
IIL(1)
Ports 0, 1, 3, 6
Output disabled
PC0, PC1
Pull-up resistor off
RESB
VIN=VSS
(including output Tr. off leakage
IIL(2)
CF1
VIN=VSS
IIL(3)
Port 2
Output disabled
current
μA
2.2 to 3.6
-1
2.2 to 3.6
-15
2.2 to 3.6
-1
IOH=-0.6mA
2.6 to 3.6
VDD-0.4
IOH=-0.4mA
2.2 to 3.6
VDD-0.4
2.6 to 3.6
VDD3-0.4
3.0 to 5.5
VDD3-0.4
2.2 to 5.5
VDD3-0.4
current)
Pull-up resistor off
VIN=VSS3
VDD3= 1.6V to 3.6V
(including output Tr. off leakage
current)
High level output
VOH(1)
voltage
VOH(2)
VOH(3)
Ports 0, 1, 3, 6
Port 2
IOH=-0.6mA
VDD3= 2.6V to 3.6V
Low level output
VOH(4)
IOH=-0.4mA
VDD3= 2.6V to 3.6V
VOH(5)
IOH=-0.2mA
VDD3= 1.6V to 3.6V
IOL=3.0mA
2.6 to 3.6
0.4
IOL=1.3mA
2.2 to 3.6
0.4
2.2 to 3.6
0.4
2.6 to 3.6
0.4
2.2 to 3.6
0.4
2.2 to 3.6
0.4
2.6 to 3.6
0.32
VOL(1)
Ports 0, 1, 6
P30 to P31,
voltage
VOL(2)
P34 to P37
VOL(3)
P32, P33
IOL=3.0mA
VOL(4)
P20 to P21,
IOL=3.0mA
P24 to P25
VDD3=1.6V to 3.6V
VOL(5)
VOL(6)
IOL=1.3mA
VDD3=1.6V to 3.6V
P22, P23
VOL(7)
IOL=3.0mA
VDD3=1.6V to 3.6V
IOL=3.0mA
VDD3=1.6V to 3.6V
Pull-up resistor
Rpu(1)
Ports 0, 1, 3, 6
VOH=0.9VDD
Rpu(2)
Port 2
VOH=0.9VDD
VDD3=2.2V to 3.6V
VOH=0.9VDD
Rpu(3)
VDD3=1.6V to 2.2V
Hysteresis
VHYS(1)
RESB
voltage
VHYS(2)
Port 2
VDD3= 1.6V to 3.6V
PnFSA=1 or other function is in
2.2 to 3.6
18
55
150
2.2 to 3.6
18
55
150
2.2 to 3.6
30
80
200
2.2 to 3.6
0.1VDD
2.2 to 3.6
0.1VDD3
2.2 to 3.6
0.1VDD
2.2 to 3.6
10
V
kΩ
V
input state
VHYS(3)
Ports 0, 1, 3
PnFSA=1 or other function is in
input state
Pin capacitance
CP
All pins
Pins other than that under test
VIN=VSS, f=1MHz, Ta=25°C
pF
No.A1860-15/33
LC88F5LA4ACS
Serial I/O Characteristics at Ta = -40 to +85°C, VSS1 = VSS2 = VSSA = 0V
Serial I/O Characteristics (Wakeup Function Disabled) (Note 4-1-1)
Parameter
Symbol
Period
tSCK(1)
Low level
tSCKL(1)
Applicable
SCK0 (P12)
Specification
Conditions
Pin/Remarks
VDD[V]
• See Fig. 6.
tSCKHA(1)
Input clock
tSCKH(1)
pulse width
typ
max
unit
4
2
pulse width
High level
min
2
• Automatic communication
mode
• See Fig. 6.
6
2.2 to 3.6
tCYC
• Automatic communication
tSCKHBSY(1a)
mode
23
• See Fig. 6.
• Mode other than automatic
tSCKHBSY(1b)
4
communication mode
Serial clock
• See Fig. 6.
Period
tSCK(2)
SCK0 (P12)
• CMOS output selected
4
• See Fig. 6.
Low level
tSCKL(2)
1/2
pulse width
High level
tSCK
tSCKH(2)
1/2
pulse width
• Automatic communication
Output clock
tSCKHA(2)
mode
• CMOS output selected
2.2 to 3.6
6
• See Fig. 6.
• Automatic communication
tSCKHBSY(2a)
mode
4
• CMOS output selected
23
tCYC
• See Fig. 6.
• Mode other than automatic
tSCKHBSY(2b)
communication mode
4
Data setup time
tsDI(1)
SI0 (P11),
SB0 (P11)
thDI(1)
Output
tdD0(1)
Input clock
Data hold time
Output clock
Serial output
Serial input
• See Fig. 6.
• Specified with respect to rising
0.03
edge of SIOCLK
• See Fig. 6.
2.2 to 3.6
0.03
SO0 (P10),
• (Note 4-1-2)
SB0 (P11)
delay time
1tCYC
+0.05
tdDO(2)
• (Note 4-1-2)
μs
2.2 to 3.6
1tCYC
+0.05
Note 4-1-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-1-2: Specified with respect to the falling edge of SIOCLK. Specified as the interval up to the time an output
change begins in the open drain output mode. See Fig. 6.
No.A1860-16/33
LC88F5LA4ACS
SIO0 Serial Input/Output Characteristics (Wakeup Function Enabled) (Note 4-2-1)
Input clock
Serial clock
Parameter
Period
tSCK(3)
Low level
tSCKL(3)
SCK0 (P12)
High level
tSCKH(3)
pulse width
tSCKHBSY(3)
Data hold time
Specification
Conditions
VDD[V]
• See Fig. 6.
tsDI(2)
min
typ
max
unit
2
2.2 to 3.6
1
tCYC
1
2
SI0 (P11),
SB0 (P11)
• Specified with respect to
thDI(2)
0.03
rising edge of SIOCLK
• See Fig. 6.
2.2 to 3.6
0.03
Output
Input clock
Serial input
Applicable
Pin/Remarks
pulse width
Data setup time
Serial output
Symbol
delay time
tdD0(3)
SO0 (P10),
μs
• (Note 4-2-2)
SB0 (P11)
2.2 to 3.6
1tCYC
+0.05
Note 4-2-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-2-2: Specified with respect to the falling edge of SIOCLK. Specified as the interval up to the time an output
change begins in the open drain output mode. See Fig.6.
No.A1860-17/33
LC88F5LA4ACS
SIO1 Serial Input/Output Characteristics (Wakeup Function Disabled) (Note 4-3-1)
Parameter
Symbol
Period
tSCK(4)
Low level
tSCKL(4)
Applicable
SCK1 (P36)
Specification
Conditions
Pin/Remarks
VDD[V]
• See Fig. 6.
tSCKHA(4)
Input clock
tSCKH(4)
pulse width
typ
max
unit
4
2
pulse width
High level
min
2
• Automatic communication
mode
• See Fig. 6.
6
2.2 to 3.6
tCYC
• Automatic communication
tSCKHBSY(4a)
mode
23
• See Fig. 6.
• Mode other than automatic
tSCKHBSY(4b)
4
communication mode
Serial clock
• See Fig. 6.
Period
tSCK(5)
SCK1 (P36)
• CMOS output selected
4
• See Fig. 6.
Low level
tSCKL(5)
1/2
pulse width
High level
tSCK
tSCKH(5)
1/2
pulse width
• Automatic communication
Output clock
tSCKHA(5)
mode
• CMOS output selected
2.2 to 3.6
6
• See Fig. 6.
• Automatic communication
tSCKHBSY(5a)
mode
4
• CMOS output selected
23
tCYC
• See Fig. 6.
• Mode other than automatic
tSCKHBSY(5b)
communication mode
4
• See Fig. 6.
Serial input
Data setup time
SI1 (P35),
SB1 (P25)
• Specified with respect to rising
Data hold time
0.03
edge of SIOCLK
• See Fig. 6.
thDI(3)
2.2 to 3.6
0.03
Input clock
Output
tdD0(4)
delay time
SO1 (P34),
• (Note 4-3-2)
SB1 (P35)
1tCYC
μs
+0.05
tdDO(5)
Output clock
Serial output
tsDI(3)
• (Note 4-3-2)
2.2 to 3.6
1tCYC
+0.05
Note 4-3-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-3-2: Specified with respect to the falling edge of SIOCLK. Specified as the interval up to the time an output
change begins in the open drain output mode. See Fig. 6.
No.A1860-18/33
LC88F5LA4ACS
SIO1 Serial Input/Output Characteristics (Wakeup Function Enabled) (Note 4-4-1)
Input clock
Serial clock
Parameter
Period
tSCK(6)
Low level
tSCKL(6)
Applicable
SCK1 (P36)
Specification
Conditions
Pin/Remarks
VDD[V]
min
• See Fig. 6.
typ
1
High level
tSCKH(6)
1
pulse width
tSCKHBSY(6)
2
tsDI(4)
SI1 (P35),
SB1 (P35)
unit
tCYC
• Specified with respect to rising
edge of SIOCLK
• See Fig. 6.
Data hold time
max
2
2.2 to 3.6
pulse width
Data setup time
Serial input
Symbol
thDI(4)
0.03
2.2 to 3.6
0.03
Input clock
Serial output
μs
Output
tdD0(6)
SO1 (P34),
• (Note 4-4-2)
SB1 (P35)
delay time
1tCYC
2.2 to 3.6
+0.05
Note 4-4-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-4-2: Specified with respect to the falling edge of SIOCLK. Specified as the interval up to the time an output
change begins in the open drain output mode. See Fig. 6.
SMIIC0 Simple SIO Mode Input/Output Characteristics
Input clock
Symbol
Period
tSCK(7)
Low level
tSCKL(7)
Applicable
SM0CK (P32)
VDD[V]
See Fig. 6.
Period
SM0CK (P32)
• CMOS output selected
tSCKL(8)
4
1/2
tSCK
tSCKH(8)
1/2
pulse width
Serial input
Data setup time
SM0DA (P33)
• Specified with respect to rising
0.03
edge of SIOCLK
• See Fig. 6.
Data hold time
thDI(5)
2.2 to 3.6
0.03
Output delay
Serial output
tsDI(5)
unit
2
2.2 to 3.6
pulse width
High level
max
2
• See Fig. 6.
Low level
typ
tCYC
tSCKH(7)
tSCK(8)
min
4
2.2 to 3.6
pulse width
High level
Specification
Conditions
Pin/Remarks
pulse width
Output clock
Serial clock
Parameter
time
tdD0(7)
SM0DO (P34),
SM0DA (P33)
μs
• Specified with respect to falling
edge of SIOCLK
• Specified as interval up to time
when output state starts
2.2 to 3.6
1tCYC
+0.05
changing.
• See Fig. 6.
Note 4-5-1: These specifications are theoretical values. Add margin depending on its use.
No.A1860-19/33
LC88F5LA4ACS
SMIIC0 I2C Mode Input/Output Characteristics
Clock
Input clock
Parameter
Symbol
Period
tSCL
Low level
tSCLL
Applicable
SM0CK (P32)
VDD[V]
• See Fig. 8.
Output clock
SM0CK (P32)
• Specified as interval up to time
tSCLLx
2.5
2.2 to 3.6
pulse width
High level
1/2
tSCL
tSCLHx
1/2
pulse width
SM0CK and SM0DA
tsp
pins input spike
unit
10
when output state starts changing.
Low level
max
2
pulse width
tSCLx
typ
Tfilt
tSCLH
Period
min
5
2.2 to 3.6
pulse width
High level
Specification
Conditions
Pin/Remarks
SM0CK (P32)
• See Fig. 8.
SM0DA (P33)
2.2 to 3.6
1
Tfilt
suppression time
time between
start and stop
tBUF
SM0CK (P32)
• See Fig. 8.
SM0DA (P33)
Input
Bus release
2.5
SM0CK (P32)
• Standard clock mode
SM0DA (P33)
• Specified as interval up to time
Output
tBUFx
Tfilt
2.2 to 3.6
5.5
when output state starts changing.
μs
• High-speed clock mode
• Specified as interval up to time
1.6
when output state starts changing.
Start/restart
tHD;STA
condition hold
SM0DA (P33)
• When SMIIC register control bit,
2.0
SHDS=0
• See Fig. 8.
Input
time
SM0CK (P32)
Tfilt
• When SMIIC register control bit,
SHDS=1
• See Fig. 8.
SM0CK (P32)
• Standard clock mode
SM0DA (P33)
• Specified as interval up to time
Output
tHD;STAx
2.5
2.2 to 3.6
4.1
when output state starts changing.
μs
• High-speed clock mode
• Specified as interval up to time
1.0
when output state starts changing.
time
tSU;STA
SM0CK (P32)
• See Fig. 8.
SM0DA (P33)
1.0
tSU;STAx
Output
condition setup
Input
Restart
SM0CK (P32)
• Standard clock mode
SM0DA (P33)
• Specified as interval up to time
2.2 to 3.6
5.5
when output state starts changing.
μs
• High-speed clock mode
• Specified as interval up to time
Tfilt
1.6
when output state starts changing.
Continued on next page.
No.A1860-20/33
LC88F5LA4ACS
Continued from preceding page
Parameter
Symbol
setup time
tSU;STO
Input
Stop condition
Applicable
SM0CK (P32)
Specification
Conditions
Pin/Remarks
VDD[V]
SM0DA (P33)
typ
max
1.0
SM0CK (P32)
• Standard clock mode
SM0DA (P33)
• Specified as interval up to time
Output
tSU;STOx
min
unit
• See Fig. 8.
2.2 to 3.6
Tfilt
4.9
when output state starts changing.
μs
• High-speed clock mode
• Specified as interval up to time
1.6
when output state starts changing.
tHD;DAT
Input
Data hold time
Output
Input
• Specified as interval up to time
2.2 to 3.6
when output state starts changing.
Output
Tfilt
1
1.5
• See Fig. 8.
1
• Specified as interval up to time
2.2 to 3.6
Tfilt
1tSCL
when output state starts changing.
-1.5Tfilt
tF
SM0CK (P32)
• See Fig. 8.
SM0DA (P33)
tF
Output
SM0CK (P32)
SM0DA (P33)
Input
time
SM0CK (P32)
0
SM0DA (P33)
tSU;DATx
SM0DA pins fall
SM0CK (P32)
SM0DA (P33)
tSU;DAT
SM0CK and
• See Fig. 8.
SM0DA (P33)
tHD;DATx
Data setup time
SM0CK (P32)
SM0CK (P32)
SM0DA (P33)
2.2 to 3.6
• When SMIIC register control bits,
2.8
PSLW=1, PHV=1
300
20
+0.1Cb
250
ns
• SM0CK, SM0DA port output
FAST mode
2.6 to 3.6
100
• Cb≤100pF
Note 4-6-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-6-2: The value of Tfilt is determined by the values of the register SMIC0BRG, bits 7 and 6 (BRP1, BRP0) and
the system clock frequency.
BRP1
BRP0
Tfilt
0
0
tCYC×1
0
1
tCYC×2
1
0
tCYC×3
1
1
tCYC×4
Set bits (BPR1, BPR0) so that the value of Tfilt falls between the following range:
250ns ≥ Tfilt >140ns
Note 4-6-3: Cb represents the total loads (in pF) connected to the bus pins. Cb ≤ 100pF
Note 4-6-4: The standard clock mode refers to a mode that is entered by configuring SMIC0BRG as follows:
250ns ≥ Tfilt >140ns
BRDQ (bit5) = 1
SCL frequency setting ≤ 100kHz
The high-speed clock mode refers to a mode that is entered by configuring SMIC0BRG as follows:
250ns ≥ Tfilt >140ns
BRDQ (bit5) = 0
SCL frequency setting ≤ 400kHz
No.A1860-21/33
LC88F5LA4ACS
SLIIC0 Simple SIO Mode Input/Output Characteristics
Input clock
Serial clock
Parameter
Symbol
Period
tSCK(7)
Low level
tSCKL(7)
Applicable
SL0CK (P22)
VDD[V]
See Fig. 8.
tSCKH(7)
Serial input
tsDI(5)
SL0DA (P23)
max
unit
tCYC
2
• Specified with respect to rising
0.03
edge of SIOCLK
• See Fig. 8.
Data hold time
typ
2
pulse width
Data setup time
min
4
2.2 to 3.6
pulse width
High level
Specification
Conditions
Pin/Remarks
thDI(5)
2.2 to 3.6
0.03
Serial output
μs
Output delay time
tdD0(7)
SL0DO (P24),
SL0DA (P23)
• Specified with respect to falling
edge of SIOCLK
• Specified as interval up to time
2.2 to 3.6
when output state starts changing.
1tCYC
+0.05
• See Fig. 8.
Note 4-7-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-7-2: When not specified, VDD3=1.6V to 3.6V (VDD3≤VDD)
No.A1860-22/33
LC88F5LA4ACS
SLIIC1 I2C Mode Input/Output Characteristics
Input clock
Clock
Parameter
Symbol
Period
tSCL
Low level
tSCLL
Applicable
SL0CK (P22)
VDD[V]
• See Fig. 8.
tSCLH
tsp
pins input spike
typ
max
unit
Tfilt
2.5
2
pulse width
SL0CK and SL0DA
min
5
2.2 to 3.6
pulse width
High level
Specification
Conditions
Pin/Remarks
SL0CK (P22)
• See Fig. 8.
SL0DA (P23)
2.2 to 3.6
1
Tfilt
suppression time
time between
start and stop
tBUF
Start/restart
• See Fig. 8.
2.2 to 3.6
tHD;STA
condition hold
SL0CK (P22)
SL0DA (P23)
2.5
Tfilt
• When SLIIC register control bit,
SHDS=0
• See Fig. 8.
Input
time
SL0CK (P22)
SL0DA (P23)
Input
Bus release
• When SLIIC register control bit
2.0
2.2 to 3.6
Tfilt
2.5
SHDS=1
• See Fig. 8.
condition setup
time
tSU;STA
setup time
tSU;STO
tHD;DAT
SL0CK (P22)
SL0CK (P22)
Output
SL0DA (P23)
Tfilt
2.2 to 3.6
1.0
Tfilt
• See Fig. 8.
• See Fig. 8.
• Specified as interval up to time
2.2 to 3.6
Tfilt
when output state starts changing.
1
tSU;DAT
SL0CK (P22)
1.5
• See Fig. 8.
Input
SL0DA (P23)
1
tSU;DATx
Output
1.0
0
tHD;DATx
Data setup time
SL0CK (P22)
2.2 to 3.6
SL0DA (P23)
Input
Data hold time
• See Fig. 8.
SL0DA (P23)
Input
Stop condition
SL0CK (P22)
SL0DA (P23)
Input
Restart
SL0CK (P22)
SL0DA (P23)
• Specified as interval up to time
when output state starts changing.
2.2 to 3.6
Tfilt
1tSCL
-1.5Tfilt
Continued on next page.
No.A1860-23/33
LC88F5LA4ACS
Continued from preceding page
Parameter
Symbol
SM0DA pins fall
time
tF
Input
SM0CK and
Applicable
SM0CK (P32)
VDD[V]
SM0CK (P32)
SM0DA (P33)
2.2 to 3.6
• When SLIIC0 register control bits
PSLW=1, PHV=1
2.8 to 3.6
When VDD3=2.8V
• When SLIIC0 register control bits
Output
min
typ
max
unit
• See Fig. 8.
SM0DA (P33)
tF
Specification
Conditions
Pin/Remarks
PSLW=1, PHV=1
2.2 to 3.6
When VDD=1.8
300
20
+0.1Cb
20
+0.1Cb
250
ns
250
• SL0CK, SL0DA port output FAST
mode
2.6 to 3.6
100
• Cb≤100pF
Note 4-8-1: The value of Tfilt is determined by the values of the register SLIC0PCNT, bits 5 and 4 (BRP1, BRP0) and
the system clock frequency.
BRP1
BRP0
Tfilt
0
0
tCYC×1
0
1
tCYC×2
1
0
tCYC×3
1
1
tCYC×4
Set bits (BPR1, BPR0) so that the value of Tfilt falls between the following range:
250ns ≥ Tfilt > 140ns
Note 4-8-2: Cb represents the total loads (in pF) connected to the bus pins. Cb ≤ 100pF
Note 4-8-3: When not specified, VDD3=1.6V to 3.6V (VDD3≤VDD)
No.A1860-24/33
LC88F5LA4ACS
UART0 Operating Conditions at Ta = -40 to +85°C, VSS1 = VSS2 = VSSA = 0V
Parameter
Transfer rate
Symbol
UBR0
Applicable
Pin/Remarks
Specification
Conditions
VDD[V]
min
typ
max
unit
U0RX (P13),
U0TX (P14),
2.2 to 3.6
4
8
tBGCYC
U0BRG (P07)
Note 4-9: tBGCYC denotes one cycle of the baudrate clock source.
UART2 Operating Conditions at Ta = -40 to +85°C, VSS1 = VSS2 = VSSA = 0V
Parameter
Transfer rate
Symbol
UBR2
Applicable
Pin/Remarks
Specification
Conditions
VDD[V]
U2RX (P16),
min
2.2 to 3.6
U2TX (P17)
typ
max
8
4096
unit
tBGCYC
Note 4-10: tBGCYC denotes one cycle of the baudrate clock source.
Pulse Input Conditions at Ta = -40 to +85°C, VSS1 = VSS2 = VSSA = 0V
Parameter
Symbol
Applicable
Pin/Remarks
VDD[V]
High/low level
tPIH(1)
INT0 (P30),
• Interrupt source flag can be set.
pulse width
tPIL(1)
INT1 (P31),
• Event inputs for timers 2 and 3
INT2 (P14),
Specification
Conditions
min
typ
max
unit
are enabled.
INT3 (P15),
INT4 (P20),
2.2 to 3.6
2
tCYC
2.2 to 3.6
10
μs
INT5 (P21),
INT6 (P24),
INT7 (P25)
tPIL(2)
RESB
Resetting is enabled.
Note 4-11: When not specified, VDD3=1.6V to 3.6V (VDD3≤VDD)
No.A1860-25/33
LC88F5LA4ACS
AD Converter Characteristics at Ta = -40 to +85°C, VSS1 = VSS2 = VSSA = 0V
12-bit AD Conversion Mode
Parameter
Applicable Pin
Symbol
/Remarks
Resolution
NAD
AN0 (P00),
Absolute accuracy
ETAD
AN1 (P01),
Conversion time
TCAD12
Analog input
AN2 (P60),
AN3 (P61)
Specification
Conditions
VDD[V]
min
typ
2.6 to 3.6
max
unit
12
bit
(Note 6-1)
2.6 to 3.6
Conversion time calculated
3.0 to 3.6
32
209
2.6 to 3.6
67
209
2.6 to 3.6
VSSA
VDDA
VAIN
voltage range
Analog port
IAINH
VAIN=VDD
2.6 to 3.6
input current
IAINL
VAIN=VSS
2.6 to 3.6
±16
1
-1
LSB
μs
V
μA
Conversion time calculation formula: TCAD12= ((52/(AD division ratio))+2) × tCYC
8-bit AD Conversion Mode
Parameter
Symbol
Applicable Pin
/Remarks
Resolution
NAD
AN0 (P00),
Absolute accuracy
ETAD
AN1 (P01),
Conversion time
TCAD8
Analog input
AN2 (P60),
AN3 (P61)
Specification
Conditions
VDD[V]
min
2.6 to 3.6
typ
max
unit
8
bit
(Note 6-1)
2.6 to 3.6
Conversion time calculated
3.0 to 3.6
20
129
2.6 to 3.6
42
129
2.6 to 3.6
VSSA
VDDA
VAIN
voltage range
Analog port
IAINH
VAIN=VDD
2.6 to 3.6
input current
IAINL
VAIN=VSS
2.6 to 3.6
±1.5
1
-1
LSB
μs
V
μA
Conversion time calculation formula: TCAD8= ((32/(AD division ratio))+2) × tCYC
Note 6-1: The quantization error (±1/2LSB) is excluded from the absolute accuracy.
Note 6-2: The conversion time refers to the interval from the time a conversion starting instruction is issued till the time
the complete digital value against the analog input value is loaded in the result register.
The conversion time is twice the normal value when one of the following conditions occurs:
• The first AD conversion is executed in the 12-bit AD conversion mode after a system reset.
• The first AD conversion is executed after the AD conversion mode is switched from 8-bit to 12-bit AD conversion
mode.
No.A1860-26/33
LC88F5LA4ACS
Consumption Current Characteristics at Ta=-40 to +85°C, VSS1=VSS2=VSSA=0V
typ: 3.0V
Parameter
Normal mode
Symbol
IDDOP(1)
consumption
current
(Note 7-1)
Applicable
Pin/Remarks
Specification
Conditions
VDD[V]
VDD1
=VDD2
• FmCF=10MHz ceramic oscillation mode
=VDDA
≥VDD3
• FmX'tal=32.768kHz crystal oscillation mode
min
typ
max
unit
• FmMRC=0MHz (oscillation stoped)
• System clock set to 10MHz
2.6 to 3.6
3.89
7.2
2.6 to 3.6
3.72
6.6
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDOP(2)
• FmCF=0Hz (oscillation stopped)
• FmMRC=10MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode
• System clock set to 10MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDOP(3)
mA
• FmCF=0Hz (oscillation stopped)
• FmMRC=4MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode
• System clock set to 4MHz
2.2 to 3.6
2.28
3.2
2.2 to 3.6
0.62
1.8
2.2 to 3.6
24.4
65
• Internal RC oscillation stopped
• 1/1 frequency division mode
IDDOP(4)
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
• System clock set to internal RC oscillation
• 1/1 frequency division mode
IDDOP(5)
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
• System clock set to 32.768kHz
μA
• Internal RC oscillation stopped
• 1/1 frequency division mode
Note 7-1: The consumption current value includes none of the currents that flow into the output transistor and internal
pull-up resistors.
Continued on next page.
No.A1860-27/33
LC88F5LA4ACS
Continued from preceding page.
Parameter
Symbol
HALT mode
IDDHALT(1)
consumption
current
(Note 7-1)
Applicable
Specification
Conditions
Pin/Remarks
VDD[V]
VDD1
=VDD2
• HALT mode
=VDDA
≥VDD3
• FmMRC=0MHz (oscillation stoped)
min
typ
max
unit
• FmCF=10MHz ceramic oscillation mode
• FmX'tal=32.768kHz crystal oscillation mode
2.6 to 3.6
1.18
2.0
2.6 to 3.6
1.05
1.8
• System clock set to 10MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
• HALT mode
IDDHALT(2)
• FmCF=0Hz (oscillation stopped)
• FmMRC=10MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode
• System clock set to 10MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
mA
• HALT mode
IDDHALT(3)
• FmCF=0Hz (oscillation stopped)
• FmMRC=4MHz oscillator mode
• FmX'tal=32.768kHz crystal oscillation mode
2.2 to 3.6
0.44
0.8
2.2 to 3.6
0.12
0.5
2.2 to 3.6
8.21
40
• System clock set to 4MHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
• HALT mode
IDDHALT(4)
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
• System clock set to internal RC oscillation
• 1/1 frequency division mode
• HALT mode
IDDHALT(5)
• FmCF=0Hz (oscillation stopped)
• FmMRC=0Hz (oscillation stopped)
• FmX'tal=32.768kHz crystal oscillator mode
• System clock set to 32.768kHz
• Internal RC oscillation stopped
• 1/1 frequency division mode
HOLD mode
IDDHOLD(1)
VDD1
• CF1=VDD or open (external clock mode)
consumption
μA
HOLD mode
2.2 to 3.6
0.02
20
2.2 to 3.6
5.2
35
current
HOLDX
IDDHOLD(2)
HOLDX mode
mode
• CF1=VDD or open (external clock mode)
consumption
• FmX'tal=32.768kHz crystal oscillator mode
current
Note 7-1: The consumption current value includes none of the currents that flow into the output transistor and internal
pull-up resistors.
F-ROM Programming Characteristics at Ta = +10°C to +55°C, VSS1=VSS2=VSSA=0V
Parameter
Onboard
Symbol
IDDFW(1)
programming
Applicable
VDD1
Specification
Conditions
Pin/Remarks
VDD[V]
min
typ
max
unit
• Microcontroller erase current current is
excluded.
2.6 to 3.6
7
mA
current
Onboard
tFW(1)
• 128-/1K-byte erase operation
2.6 to 3.6
30
ms
tFW(2)
• 2-byte programming operation
2.6 to 3.6
60
μs
programming
time
No.A1860-28/33
LC88F5LA4ACS
Power Pin Treatment Conditions 1 (VDD1, VSS1)
Connect capacitors that meet the following conditions between the VDD1 and VSS1 pins:
• Connect among the VDD1 and VSS1 pins and the capacitors C1 and C2 with the shortest possible lead wires,
of the same length (L1=L1', L2=L2') wherever possible.
• Connect a large-capacity capacitor C1 and a small-capacity capacitor C2 in parallel.
The capacitance of C2 should be approximately 0.1μF or larger.
• The VDD1 and VSS1 traces must be thicker than the other traces.
L2
L1
VSS1
C1
C2
VDD1
L1’
L2’
Power Pin Treatment Conditions 2 (VDD(2, 3), VSS(2))
Connect capacitors that meet the following condition between the VDD(2) and VSS(2), VDD(3) and VSS(2) pins:
• Connect among the VDD(2, 3) and VSS(2) pins and the capacitor C3 with the shortest possible lead wires,
of the same length (L3=L3') wherever possible.
• The capacitance of C3 should be approximately 0.1μF or larger.
• The VDD(2, 3) and VSS(2) traces must be thicker than the other traces.
L3
VSS(2)
C3
VDD(2, 3)
L3’
Power Pin Treatment Conditions 3 (VDDA, VSSA)
Connect capacitors that meet the following condition between the VDDA and VSSA pins:
• Connect among the VDDA and VSSA pins and the capacitor C4 with the shortest possible lead wires,
of the same length (L4=L4') wherever possible.
• The capacitance of C4 should be approximately 0.1μF or larger.
• The VDDA and VSSA traces must be thicker than the other traces.
L4
VSSA
C4
VDDA
L4’
No.A1860-29/33
LC88F5LA4ACS
Characteristics of a Sample OSC1 System Clock Oscillation Circuit
Given below are the characteristics of a sample main system clock oscillation circuit that are measured using a
SANYO-designated oscillation characteristics evaluation board and external components with circuit constant values
with which the oscillator vendor confirmed normal and stable oscillation.
Table 1 Characteristics of a Sample Main System Clock Oscillator Circuit with a Ceramic Resonator
Nominal
Vendor
Frequency
Name
10MHz
8MHz
MURATA
4MHz
Circuit Constant
Resonator
Operating
Oscillation
Voltage
Stabilization Time
C3
C4
Rf
Rd2
Range
typ
max
[pF]
[pF]
[Ω]
[Ω]
[V]
[ms]
[ms]
CSTCE10M0G52-R0
(10)
(10)
OPEN
0
2.2 to 3.6
0.02
0.2
CSTCE8M00G52-R0
(10)
(10)
OPEN
0
2.2 to 3.6
0.02
0.2
CSTCR4M00G53-R0
(15)
(15)
OPEN
680
2.2 to 3.6
0.02
0.2
Remarks
C1, C2
integrated type
C1, C2
integrated type
C1, C2
integrated type
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after VDD
goes above the lower limit level of the operating voltage range (see Figure 4)
Characteristics of a Sample System Clock Oscillator Circuit
Given below are the characteristics of a sample subsystem clock oscillation circuit that are measured using a SANYOdesignated oscillation characteristics evaluation board and external components with circuit constant values with which
the oscillator vendor confirmed normal and stable oscillation.
Table 2 Characteristics of a Sample Subsystem Clock Oscillator Circuit with a Crystal Resonator
Nominal
Vendor
Frequency
Name
32.768kHz
EPSON
TOYOCOM
Circuit Constant
Oscillator Name
MC-306
Operating
Oscillation
Voltage
Stabilization Time
C3
C4
Rf2
Rd2
Range
typ
max
[pF]
[pF]
[Ω]
[Ω]
[V]
[s]
[s]
18
18
OPEN
0
2.2 to 3.6
0.9
2
Remarks
Applicable
CL value=12.5pF
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after the
instruction for starting the subclock oscillator circuit is executed plus the time interval that is required for the oscillation
to get stabilized after the HOLD mode is released (see Figure 4).
Note: The traces to and from the components that are involved in oscillation should be kept as short as possible as the
oscillation characteristics are affected by their trace pattern.
CF1
CF2
XT1
Rf1
Rf2
Rd1
C1
C2
XT2
Rd2
C3
C4
X’tal
CF
Figure 1 CF Oscillator Circuit
Figure 2 XT Oscillator Circuit
0.5VDD
Figure 3 AC Timing Measurement Point
No.A1860-30/33
LC88F5LA4ACS
VDD
Operating VDD
lower limit
0V
Power
Reset time
RESB
Internal RC
oscillation
tmsCF
CF1, CF2
tmsX'tal
XT1, XT2
Operating
mode
Unpredictable
Reset
Initialization
instruction execution
User instruction execution
Reset Time and Oscillation Stabilization Time
HOLD release
No HOLD release signal
HOLD release signal valid
Interrupt operation
Internal RC
oscillation
tmsCF
CF1, CF2
tmsX'tal
XT1, XT2
State
HOLD
HALT
Instruction execution
HOLD Release and Oscillation Stabilization Time
Figure 4 Oscillation Stabilization Time Timing Charts
No.A1860-31/33
LC88F5LA4ACS
VDD
Note:
Reset signal must be present when power
supply rises.
Determine the value of CRES and RRES so
that the reset signal is present for 10μs after the
supply voltage gets stabilized.
RRES
RES
CRES
Figure 5 Reset Circuit
tSCKHBSY
tSCKHBSY
RUN:
SIOCLK:
DATAIN:
DI0
DI1
DI6
DI7
DI8
DIx
DATAOUT:
DO0
DO1
DO6
DO7
DO8
DOx
Data RAM transfer period
(SIO0 and SIO1 only)
tSCK
SIOCLK:
tSCKL
tSCKH
tsDI
thDI
DATAIN:
tdDO
DATAOUT:
Data RAM transfer period
(SIO0 and SIO1 only)
SIOCLK:
tSCKL
tSCKHA
tsDI
thDI
DATAIN:
tdDO
DATAOUT:
* Remarks: DIx and DOx denote the last bits communicated; x = 0 to 32768
Figure 6 Serial I/O Waveforms
tPIL
tPIH
Figure 7 Pulse Input Timing Signal Waveform
No.A1860-32/33
LC88F5LA4ACS
P
S
Sr
P
SDA
tBUF
tHD;STA tR
tF
tHD;STA
tsp
SCK
tLOW
tHD;DAT tHIGH
tSU;DAT
tSU;STA
tSU;STO
S: Start condition
P: Stop condition
Sr: Restart condition
Figure 8 I2C Timing
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of March, 2010. Specifications and information herein are subject
to change without notice.
PS No.A1860-33/33