120W Single Output Power Supply or Battery Charger PA / P B - 1 2 0 series Features : AC input range selected by switch Built-in passive PFC function compliance to EN61000-3-2 With AC ON-OFF switch 3 poles AC inlet with fuse holder Protections: Short circuit / Overload / Over voltage / Over temperature Charger type can be selected (Optional) Charger for lead-acid batteries 2 color LED loading indicator Open frame models available (Without safety approval) Low cost, High reliability 2 years warranty TUV Rheinland Product Safety S:Power Supply A:Voltage detector B:Current detector P A 120 P geprUfre Sicherheit 13 C :O.D.M. number P:Open P.C.B. C:With case 13:13.8V 27:27.6V 54:55.2V P:With PFC N:None PFC SPECIFICATION MODEL OUTPUT PA/PB-120 PA/PB-120 -27 PA/PB-120 13.8V 27.6V 55.2V RATED CURRENT 7.2A 4.3A 2.2A CURRENT RANGE 0 ~ 7.2A 0 ~ 4.3A 0 ~ 2.2A RATED POWER 99.36W 118.68W 121.44W LED INDICATED INPUT -13 DC VOLTAGE PA series voltage 105% 1% PB series load 46% 10% : RED / 105% 1% : GREEN / 46% 10% VOLTAGE RANGE 88 ~ 132VAC / 176 ~ 264VAC selected by switch FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) >0.65 (with PFC series) :GREEN :RED EFFICIENCY (Typ.) 73% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 3A/115VAC 1.5A/230VAC COLD START 25A/115VAC LEAKAGE CURRENT <1.5mA / 240VAC OVERLOAD 90 ~ 110% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. -54 79% 79% 50A/230VAC 15 ~ 17V 30 ~ 35V 60 ~ 66V Protection type : Hiccup mode, recovers automatically after fault condition is removed RTH2 70 10 detect on RTH2 thermistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +45 (Refer to output load derating curve) 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.05%/ (0 ~ 45 VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & EMC (Note 4) OTHERS ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B HARMONIC CURRENT EMS IMMUNITY Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A MTBF DIMENSION 149.6K hrs min. PACKING NOTE UL60950-1, TUV EN60950-1, EN60335, EN60335-1, EN60335-2-29 approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC MIL-HDBK-217F (25 ) PCB Type:144*90*33mm External case type:180*96*49mm (L*W*H) 1.1Kg; 16pcs / 17.9Kg / 1.47CUFT(without PFC) 1.24Kg; 16pcs / 20.1Kg / 1.47CUFT(with PFC) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. With PFC I/P range: 95~132VAC/190~264VAC. 6. For open P.C.B. WITH 17.8CFM min. Forced air. File Name:PA,PB-120-SPEC 2008-05-06 120W Single Output Power Supply or Battery Charger PA / P B - 1 2 0 Mechanical Specification Case No. PS-120A series Unit:mm 1 2 3 115 FUSE CASE: Output cable length=183cm 5cm Assignment DC OUTPUT +V DC OUTPUT -V Pin No. 1 2,3 Pin No. 1 2 3 Assignment AC/L No Pin AC/N 49 PCB: AC Input Connector (CN1) : JST B3P-VH or equivalent Mating Housing Terminal JST VHR or equivalent JST SVH-21T-P1.1 or equivalent 180 144 4- 134 3. 5 8 12VDC FAN Output Connector (CN4) : JST B2B-XH or equivalent Assignment +V -V JST XHP or equivalent ADJ. Terminal Mating Housing CN4 JST SXH-001T-P0.6 or equivalent F4 A/250V Pin No. 1 2 CN3 +V JST SVH-21T-P1.1 or equivalent -V Terminal JST VHR or equivalent 1 2 3 4 Mating Housing 80 Assignment -V +V 90 Pin No. 1,2 3,4 5 DC Output Connector (CN3) : JST B4P-VH or equivalent LED 12 +CN5 1 2 3 SHORT FOR 115V OPEN FOR 230V CN1 Switch 115V 230V Mating Housing Terminal JST VHR or equivalent JST SVH-21T-P1.1 or equivalent 2 max. Assignment Short Open 33 115/230V selected by switch Connector (CN5) : JST B2P-VH or equivalent Derating Curve Charging Curve Vout 105% 100% 100 Charging Current Open frame series 17.8CFM air cooling (L=15cm face HS) 80 Iout Bat. Voltage 100% 45% Other series LOAD (%) 60 Red LED COLOR Green T Type A:Voltage detecter,pulse charger 40 Vout 105% 100% Iout Bat. Voltage 20 Charging Current -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 100% (HORIZONTAL) LED COLOR Red Green Type B:Current detecter,2 voltage section T File Name:PA,PB-120-SPEC 2008-05-06