SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
D Three Differential Transceivers in One
D
D
D
D
D
D
D
D
D
D
D
Package
Signaling Rates† Up to 30 Mbps
Low Power and High Speed
Designed for TIA/EIA-485, TIA/EIA-422, ISO
8482, and ANSI X3.277 (HVD SCSI Fast−20)
Applications
Common-Mode Bus Voltage Range
–7 V to 12 V
ESD Protection on Bus Terminals
Exceeds 12 kV
Driver Output Current up to ±60 mA
Thermal Shutdown Protection
Driver Positive and Negative Current
Limiting
Power-Up, Power-Down Glitch-Free
Operation
Pin-Compatible With the SN75ALS170
Available in Shrink Small-Outline Package
SN65LBC170DB (marked as BL170)
SN75LBC170DB (marked as BL170)
(TOP VIEW)
1D
1DIR
NC
GND
2D
2DIR
3D
3DIR
These devices combine three 3-state differential
line drivers and three differential input line
receivers, all of which operate from a single 5-V
power supply.
The driver differential outputs and the receiver
differential inputs are connected internally to form
three differential input/output (I/O) bus ports that
are designed to offer minimum loading to the bus
whenever the driver is disabled or VCC = 0. These
ports feature a wide common-mode voltage range
making the device suitable for party-line
applications over long cable runs.
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
1B
1A
NC
VCC
2B
2A
3B
3A
SN65LBC170DW (marked as 65LBC170)
SN75LBC170DW (marked as 75LBC170)
(TOP VIEW)
1D
1DIR
NC
GND
NC
2D
2DIR
NC
3D
3DIR
description
The SN65LBC170 and SN75LBC170 are
monolithic integrated circuits designed for
bidirectional data communication on multipoint
bus-transmission lines. Potential applications
include serial or parallel data transmission, cabled
peripheral buses with twin axial, ribbon, or
twisted-pair cabling. These devices are suitable
for FAST-20 SCSI and can transmit or receive
data pulses as short as 25 ns, with skew less
than 3 ns.
1
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
1B
1A
NC
NC
VCC
2B
2A
3B
3A
NC
NC − No internal connection
logic diagram
1DIR
1A
1B
1D
2DIR
2A
2B
2D
3DIR
3A
3B
3D
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
†The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).
Copyright 2002, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!#- '# #!#&, !&"'#
#- && $##(
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
description (continued)
The driver’s active-high enable and the receiver’s active-low enable are tied together internally and provide a
direction input for each driver/receiver pair.
The SN75LBC170 is characterized for operation over the temperature range of 0°C to 70°C. The SN65LBC170
is characterized for operation over the temperature range of −40°C to 85°C.
AVAILABLE OPTIONS†
PACKAGE
TA
PLASTIC SHRINK SMALL-OUTLINE
(JEDEC MO-150)
PLASTIC SMALL-OUTLINE
(JEDEC MS-013)
0°C to 70°C
SN75LBC170DB
SN75LBC170DW
−40°C to 85°C
SN65LBC170DB
SN65LBC170DW
† Add R suffix for taped and reel
† For the most current package and ordering information, see the Package Option Addendum at the end of this document,
or see the TI web site at www.ti.com.
Function Tables
EACH DRIVER
INPUT
D
ENABLE
DIR
EACH RECEIVER
OUTPUTS
DIFFERENTIAL INPUT ENABLE OUTPUT
(VA−VB)
DIR
D
VID ≥ 0.2 V
L
H
B
A
L
H
H
H
−0.2 V < VID < 0.2 V
L
H
L
H
L
VID ≤ −0.2 V
L
H
OPEN
H
L
X
H
Z
X
Z
L
L
OPEN
X
X
OPEN
X
H = high level, L = low level, X = irrelevant, Z = high impedance (off), ? = indeterminate
?
L
Z
H
equivalent input and output schematic diagrams
DIR INPUTS
A INPUT
B INPUT
VCC
VCC
100 kΩ
16 V
VCC
4 kΩ
4 kΩ
16 V
18 kΩ
18 kΩ
Input
1 kΩ
Input
Input
100 kΩ
16 V
16 V
4 kΩ
4 kΩ
100 kΩ
8V
A AND B OUTPUT
D I/O
VCC
VCC
VCC
16 V
4 kΩ
18 kΩ
Output
40 Ω
100 kΩ
4 kΩ
8V
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
16 V
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
absolute maximum ratings† over operating free−air temperature range (unless otherwise noted)
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Voltage range at any bus I/O terminal (steady state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −10 V to 15 V
Voltage input range, A and B, (transient pulse through 100 Ω, see Figure 12) . . . . . . . . . . . . . . −30 V to 30 V
Voltage range at any D or DIR terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.5 V to VCC + 0.5 V
Receiver output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 mA
Electrostatic discharge: Human body model (A, B, GND) (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . 12 kV
All pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 kV
Charged-device model (all pins) (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 kV
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Power Dissipation Rating Table
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.
2. Tested in accordance with JEDEC Standard 22, Test Method A114−A.
3. Tested in accordance with JEDEC Standard 22, Test Method C101.
POWER DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR}
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
515 mW
DB
995 mW
8.0 mW/°C
635 mW
DW
1480 mW
11.8 mW/°C
950 mW
770 mW
‡ This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow.
recommended operating conditions
Supply voltage, VCC
Voltage at any bus I/O terminal
High-level input voltage, VIH
Low-level input voltage, VIL
Differential input voltage, VID
Output current
Operating free-air temperature, TA
MIN
NOM
MAX
UNIT
4.75
5
5.25
V
−7
12
V
2
0
VCC
0.8
V
A with respect to B
−12
12
V
Driver
−60
60
−8
8
SN75LBC170
0
70
SN65LBC170
−40
85
A, B
D, DIR
Receiver
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
mA
°C
3
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
DRIVER SECTION
electrical characteristics over recommended operating conditions
PARAMETER
VIK
VO
Input clamp voltage
TEST CONDITIONS
D and DIR
Open-circuit output voltage (single-ended)
II = 18 mA
A or B, No load
Steady-state differential output voltage
magnitude‡
RL = 54 Ω,
See Figure 1
With common-mode loading, See Figure 2
∆VOD
Change in differential output voltage
magnitude, | VOD(H) | – |VOD(L) |
VOC(SS)
Steady-state common-mode output voltage
∆VOC(SS)
Change in steady-state common-mode output
voltage (VOC(H) – VOC(L))
II
IO
Input current
D, DIR
Output current with power off
VCC = 0 V,
VO = −7 V to 12 V,
TYP†
−1.5
−0.7
0
No load
|VOD(SS)|
MIN
See Figure 1
VO = −7 V to 12 V
See Figure 7
UNIT
V
4.3
VCC
VCC
V
3.8
1
1.6
2.4
V
1
1.6
2.4
−0.2
RL = 54 Ω,
CL = 50 pF
MAX
2
0.2
2.4
V
2.8
−0.2
0.2
V
−100
100
µA
−700
900
µA
IOS
Short-circuit output current
−250
250
mA
ICC
Supply current (driver enabled)
D at 0 V or VCC,
DIR at VCC, No load
14
20
mA
† All typical values are at VCC = 5 V and TA = 25°C.
‡ The minimum VOD may not fully comply with TIA/EIA-485-A at operating temperatures below 0°C. System designers should take the possibly
lower output signal into account in determining the maximum signal-transmission distance.
switching characteristics over recommended operating conditions
MIN
TYP
MAX
tPLH
tPHL
Differential output propagation delay, low-to high
PARAMETER
TEST CONDITIONS
4
8.5
12
Differential output propagation delay, high-to-low
4
8.5
11
tr
tf
Differential output rise time
3
7.5
11
3
7.5
11
tsk(p)
tsk(o)
Pulse skew | (tPLH – tPHL) |
Output skew§
tsk(pp)
tPLH
Part-to-part skew¶
RL = 54 Ω, CL = 50 pF, See Figure 3
Differential output fall time
1.5
2
Differential output propagation delay, low-to high
3
7
10
Differential output propagation delay, high-to-low
3
7.5
10
Differential output rise time
3
7.5
12
tf
tsk(p)
Differential output fall time
3
7.5
12
tPZH
tPHZ
See Figure 4,
(HVD SCSI double-terminated load)
Pulse skew | (tPLH – tPHL) |
Output skew§
Output disable time from high level
ns
3
1.5
Part-to-part skew¶
Output enable time to high level
ns
2
tPHL
tr
tsk(o)
tsk(pp)
UNIT
2.5
See Figure 5
15
25
18
25
ns
tPZL
Output enable time to low level
10
25
See Figure 6
ns
tPLZ
Output disable time from low level
17
25
§ Output skew (tsk(o)) is the magnitude of the time delay difference between the outputs of a single device with all of the inputs connected together.
¶ Part-to-part skew (tsk(pp)) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when
both devices operate with the same input signals, the same supply voltages, at the same temperature, and have identical packages and test
circuits.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
RECEIVER SECTION
electrical characteristics over recommended operating conditions
PARAMETER
TEST CONDITIONS
VIT+
VIT−
Positive-going differential input voltage threshold
Vhys
VOH
Hysteresis voltage (VIT+ − VIT−)
VOL
Low-level output voltage
VID = 200 mV, IOH = −8 mA, See Figure 8
VID = −200 mV, IOL = −8 mA, See Figure 8
II
Line input current
Other input = 0 V
RI
Input resistance
A, B
Negative-going differential input voltage threshold
MIN
TYP†
MAX
V
−0.2
See Figure 8
40
High-level output voltage
ICC
Supply current (receiver enabled)
† All typical values are at VCC = 5 V and TA = 25°C.
UNIT
0.2
VI = 12 V
VI = −7 V
4
4.7
0
0.2
mV
VCC
0.4
V
0.9
mA
−0.7
12
kΩ
A, B, D, and DIR open
16
mA
switching characteristics over recommended operating conditions
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tPLH
tPHL
Propagation delay time, low-to-high level output
7
16
ns
Propagation delay time, high-to-low level output
7
16
ns
tr
tf
Receiver output rise time
3
ns
Receiver output fall time
1.3
3
ns
tPZH
tPHZ
Receiver output enable time to high level
26
40
tPZL
tPLZ
Receiver output enable time to low level
tsk(p)
tsk(o)
Pulse skew (| tPLH – tPHL |)
Output skew‡
See Figure 9
Receiver output disable time from high level
1.3
See Figure 10
40
29
Receiver output enable time to high level
See Figure 11
ns
40
40
2
ns
ns
1.5
ns
tsk(pp)
Part-to-part skew§
3
ns
‡ Output skew (tsk(o)) is the magnitude of the time delay difference between the outputs of a single device with all of the inputs connected together.
§ Part-to-part skew (tsk(pp)) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when
both devices operate with the same input signals, the same supply voltages, at the same temperature, and have identical packages and test
circuits.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION
IO
27 Ω
II
0 V or 3 V
IO
VO
VOD
50 pF†
27 Ω
VOC
VO
† Includes probe and jig capacitance
Figure 1. Driver Test Circuit, VOD and VOC Without Common-Mode Loading
375 Ω
Input
VOD
60 Ω
VTEST = −7 V to 12 V
375 Ω
VTEST
Figure 2. Driver Test Circuit, VOD With Common-Mode Loading
3V
RL = 54 Ω
Signal
Generator{
Input
CL = 50 pF}
1.5 V
1.5 V
0V
VOD
tPLH
50 Ω
Output
tPHL
90% 90%
10%
tr
† PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
‡ Includes probe and jig capacitance
Figure 3. Driver Switching Test Circuit and Waveforms, 485-Loading
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10%
tf
VOD(H)
0V
VOD(L)
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION
5V
S1
0V
375 Ω
3V
60 pF‡
165 Ω
Input
1.5 V
1.5 V
0V
tPLH
75 Ω
Signal
Generator{
tPHL
VOD
165 Ω
10%
60 pF‡
375 Ω
5V
VOD(H)
0V
VOD(L)
90% 90%
Output
50 Ω
10%
tr
tf
S2
0V
† PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
‡ Includes probe and jig capacitance
Figure 4. Driver Switching Test Circuit and Waveforms, HVD SCSI-Loading (double terminated)
A
1.5 V
Output
0 V or 3 V{
1.5 V
0V
B
RL = 110 Ω
CL = 50 pF§
Input
Generator}
3V
Input
S1
0.5 V
tPZH
Output
VOH
2.3 V
0V
50 Ω
tPHZ
† 3 V if testing A output, 0 V if testing B output
‡ PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
w Includes probe and jig capacitance
Figure 5. Driver Enable/Disable Test, High Output
5V
RL = 110 Ω
A
Input
S1
0 V or 3 V{
3V
1.5 V
1.5 V
0V
Output
tPZL
B
CL = 50 pF§
Input
Output
tPLZ
5V
2.3 V
VOL
Generator‡
50 Ω
0.5 V
† 0 V if testing A output, 3 V if testing B output
‡ PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
w Includes probe and jig capacitance
Figure 6. Driver Enable/Disable Test, Low Output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION
IOS
VO
IO
VID
Voltage
Source
VO
Figure 7. Driver Short-Circuit Test
Generator{
Figure 8. Receiver DC Parameters
50 Ω
Input B
A
D
VID
Generator{
1.5 V
Input A
0V
B
CL = 15 pF}
50 Ω
3V
IO
tPLH
VO
tPHL
Output
1.5 V
10%
90%
90%
VOH
1.5 V
10% V
OL
tr
† PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
‡ Includes probe and jig capacitance
tf
Figure 9. Receiver Switching Test Circuit and Waveforms
1.5 V
VCC
A
D
B
1 kΩ
1.5 V
0V
tPZH
tPHZ
1.5 V
50 Ω
VOH
VOH −0.5 V
GND
† PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
‡ Includes probe and jig capacitance
Figure 10. Receiver Enable/Disable Test, High Output
8
1.5 V
CL = 15 pF}
DIR
Generator{
3V
DIR
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION
−1.5 V
VCC
A
D
B
DIR
3V
DIR
1 kΩ
1.5 V
1.5 V
0V
CL = 15 pF}
tPZL
tPLZ
VCC
1.5 V
Generator{
50 Ω
VOL + 0.5 V
VOL
† PRR = 1 MHz, 50% Duty Cycle, tr < 6 ns, tf < 6 ns, Zo = 50 Ω
‡ Includes probe and jig capacitance
Figure 11. Receiver Enable/Disable Test, Low Output
100 Ω
Pulse
Generator,
15-µs Duration,
1% Duty Cycle
VTEST
0V
15 µs
1.5 ms
−VTEST
Figure 12. Test Circuit and Waveform, Transient Over Voltage Test
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
TYPICAL CHARACTERISTICS
DIFFERENTIAL OUTPUT VOLTAGE
vs
OUTPUT CURRENT
DIFFERENTIAL OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
2.5
3.5
VOD − Differential Output Voltage − V
VOD − Differential Output Voltage − V
4
3
VCC = 5.25 V
2.5
VCC = 5 V
2
1.5
VCC = 4.75 V
1
0.5
0
0
20
40
60
80
IO − Output Current − mA
VCC = 5 V
1.5
VCC = 4.75 V
1
0.5
0
−60
100
VCC = 5.25 V
2
−40
Figure 13
165
160
10
I CC − Supply Current − mA
Driver Propagation Delay − ns
11
SCSI Load
9
8
RS−485 Load
6
All 3 Channels Driving
RL = 54 Ω,
CL = 50 pF (Each Channel),
Pseudorandom NRZ Data
155
150
145
140
5
−20
0
20
40
60
TA − Free-Air Temperature − °C
80
135
0.1
Figure 15
10
100
SUPPLY CURRENT
vs
SIGNALING RATE
12
4
−40
80
Figure 14
DRIVER PROPAGATION DELAY
vs
FREE-AIR TEMPERATURE
7
−20
0
20
40
60
TA − Free-Air Temperature − °C
1
10
Signaling Rate − Mbps
Figure 16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
TYPICAL CHARACTERISTICS
BUS INPUT CURRENT
vs
BUS INPUT VOLTAGE
RECEIVER PROPAGATION DELAY TIME
vs
FREE-AIR TEMPERATURE
800
t pd − Receiver Propagation Delay Time − ns
12
600
Bus Input Current − µ A
VCC = 0 V
400
VCC = 5 V
200
0
−200
−400
−600
−10
−5
0
5
10
11
10
tPHL
9
tPLH
8
7
6
5
4
−40
15
−20
Bus Input Voltage − V
Figure 17
0
20
40
60
TA − Free-Air Temperature°C
80
Figure 18
SN65LBC170
(as Driver)
15 Meters, Cat. 5
Twisted-Pair Cable
Signal
Generator
SN65LBC170
(as Receiver)
100 Ω
15 pF
Figure 19. Circuit Diagram for Signaling Characteristics
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
TYPICAL CHARACTERISTICS
Driver Input
(5 V/div)
Driver Output
(2 V/div)
Receiver Input
(2 V/div)
25 ns
Receiver Output
(5 V/div)
Figure 20. Signal Waveforms at 30 Mbps
Driver Input
(5 V/div)
Driver Output
(2 V/div)
Receiver Input
(2 V/div)
12.5 ns
Receiver Output
(5 V/div)
Figure 21. Eye Patterns, Pseudorandom Data at 30 Mbps
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLLS459C − NOVEMBER 2000 − REVISED MARCH 2005
TYPICAL CHARACTERISTICS
Driver Input
(5 V/div)
Driver Output
(2 V/div)
Receiver Input
(2 V/div)
25 ns
Receiver Output
(5 V/div)
Figure 22. Signal Waveforms at 50 Mbps
Driver Input
(5 V/div)
Driver Output
(2 V/div)
Receiver Input
(2 V/div)
12.5 ns
Receiver Output
(5 V/div)
Figure 23. Eye Patterns, Pseudorandom Data at 50 Mbps
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jul-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN65LBC170DB
ACTIVE
SSOP
DB
16
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DBG4
ACTIVE
SSOP
DB
16
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DBR
ACTIVE
SSOP
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DBRG4
ACTIVE
SSOP
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DW
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DWG4
ACTIVE
SOIC
DW
20
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DWR
ACTIVE
SOIC
DW
20
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN65LBC170DWRG4
ACTIVE
SOIC
DW
20
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DB
ACTIVE
SSOP
DB
16
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DBG4
ACTIVE
SSOP
DB
16
80
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DBR
ACTIVE
SSOP
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DBRG4
ACTIVE
SSOP
DB
16
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DW
ACTIVE
SOIC
DW
20
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DWG4
ACTIVE
SOIC
DW
20
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DWR
ACTIVE
SOIC
DW
20
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN75LBC170DWRG4
ACTIVE
SOIC
DW
20
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jul-2007
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Oct-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN65LBC170DBR
DB
16
SITE 41
330
16
8.2
6.6
2.5
12
16
Q1
SN65LBC170DWR
DW
20
SITE 41
330
24
10.8
13.0
2.7
12
24
Q1
SN75LBC170DBR
DB
16
SITE 41
330
16
8.2
6.6
2.5
12
16
Q1
SN75LBC170DBRG4
DB
16
SITE 41
330
16
8.2
6.6
2.5
12
16
Q1
SN75LBC170DWR
DW
20
SITE 41
330
24
10.8
13.0
2.7
12
24
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
4-Oct-2007
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
SN65LBC170DBR
DB
16
SITE 41
346.0
346.0
33.0
SN65LBC170DWR
DW
20
SITE 41
346.0
346.0
41.0
SN75LBC170DBR
DB
16
SITE 41
346.0
346.0
33.0
SN75LBC170DBRG4
DB
16
SITE 41
346.0
346.0
33.0
SN75LBC170DWR
DW
20
SITE 41
346.0
346.0
41.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2008, Texas Instruments Incorporated