ACS108-5Sx ® ASD™ AC Switch Family AC LINE SWITCH MAIN APPLICATIONS ■ ■ AC on-off static switching in appliance & industrial control systems Drive of low power high inductive or resistive loads like - relay, valve, solenoid, dispenser - pump, fan, micro-motor - defrost heater OUT G TO-92 ACS108-5SA FEATURES ■ Blocking voltage: VDRM / VRRM = 500V ■ Clamping voltage: VCL = 600V ■ Nominal current: IT(RMS) = 0.8 A ■ Gate triggering current : IGT < 10mA ■ Triggering current is sourced by the gate Switch integrated driver Drive reference COM connected to the SOT-223 tab ■ ■ COM OUT COM G SOT-223 ACS108-5SN BENEFITS ■ ■ ■ ■ ■ ■ COM Needs no external overvoltage protection. Enables the equipment to meet IEC61000-4-5 standard. Allows straightforward connection of several SOT-223 devices on the same cooling pad. Reduces the switch component count by up to 80%. Interfaces directly with the microcontroller. Eliminates any stressing gate kick back on the microcontroller. FUNCTIONAL DIAGRAM OUT ACS108 DESCRIPTION S The ACS108 belongs to the AC line switches built around the ASD™ concept. This high performance device is able to control an 0.8 A load device. The ACS™ switch embeds a high voltage clamping structure to absorb the inductive turn-off energy and a gate level shifter driver to separate the digital controller from the main switch. It is triggered with a negative gate current flowing out of the gate pin. For further technical information, please refer to ON D COM G ASD and ACS are a trademarks of STMicroelectronics. June 2005 REV. 2 1/8 ACS108-5Sx ABSOLUTE RATINGS (limiting values) Symbol VDRM/ VRRM IT(RMS) Parameter Repetitive peak off-state voltage ITMS Non repetitive surge peak on-state current Tj initial = 25°C, full cycle sine wave dI/dt Critical rate of repetitive rise of on-state current IG = 20mA with tr = 100ns Non repetitive line peak pulse voltage Storage temperature range Operating junction temperature range Maximum lead temperature for soldering during 10s VPP Tstg Tj Tl RMS on-state current full cycle sine wave 50 to 60 Hz TO-92 TO-92 SOT-223 Tj = 125 °C Value 500 Unit V Tlead = 75 °C Tamb = 60 °C Tamb = 75 °C F = 50 Hz F = 60 Hz F = 120 Hz 0.8 0.3 0.8 7.3 8 100 A A A A A A/µs note 1 2 - 40 to + 150 - 30 to + 125 260 kV °C °C °C Note 1: according to test described by IEC61000-4-5 standard & Figure 3. SWITCH GATE CHARACTERISTICS (maximum values) Symbol PG(AV) IGM VGM Parameter Average gate power dissipation Peak gate current (tp = 20µs) Peak positive gate voltage (respect to the pin COM) Value 0.1 1 5 Unit W A V Value 150 60 60 25 Unit °C/W °C/W °C/W °C/W THERMAL RESISTANCES Symbol Rth (j-a) Parameter Junction to ambient Rth (j-l) Rth (j-t) Junction to lead for full AC line cycle conduction Junction to tab for full AC line cycle conduction TO-92 SOT-223 (*) TO-92 SOT-223 (*) : with 5 cm2 copper (e=35µm) surface under tab ELECTRICAL CHARACTERISTICS For either positive or negative polarity of pin OUT voltage respect to pin COM voltage excepted note 3 Symbol IGT VGT VGD IH IL VTM IDRM / IRRM dV/dt (dI/dt)c (dI/dt)c* VCL 2/8 VOUT = 12V VOUT = 12V VOUT = VDRM IOUT = 100mA Test conditions RL = 140Ω RL = 140Ω RL = 3.3kΩ gate open IG = 20mA IOUT = 1.1A VOUT = VDRM VOUT = VRRM tp = 500µs VOUT = 400V gate open (dV/dt)c = 10V/µs (dV/dt)c = 15V/µsIOUT < 0 (note 3) ICL = 1mA tp = 1ms Tj = 25°C MAX. Tj = 25°C MAX. Tj = 125°C MIN. Tj = 25°C TYP. MAX. Tj = 25°C TYP. MAX. Tj = 25°C MAX. Tj = 25°C MAX. Tj = 125°C MAX. Tj = 110°C MIN. Tj = 110°C MIN. Tj = 110°C MIN. Tj = 25°C TYP. Values 10 1 0.15 25 60 30 65 1.3 2 200 500 0.1 0.3 600 Unit mA V V mA mA mA mA V µA µA V/µs A/ms A/ms V ® ACS108-5Sx AC LINE SWITCH BASIC APPLICATION The ACS108 device is well adapted to washing machines, dishwashers, tumble driers, refrigerators, water heaters and cookware. It has been especially designed to switch ON and OFF low power loads such as solenoids, valves, relays, dispensers, micro-motors, fans, pumps, door locks and low power lamp bulbs. Pin COM Pin G Pin OUT : Common drive reference to connect to the power line neutral : Switch Gate input to connect to the digital controller through the resistor : Switch Output to connect to the load This ACS™ switch is triggered with a negative gate current flowing out of the gate pin G. It can be driven directly by the digital controller through a resistor as shown on the typical application diagram. No protection devices are required between the gates and common terminals. The SOT-223 version allows several ACS108 devices to be connected on the same cooling PCB pad which is the COM pin : this cooling pad can be then reduced, and the printed circuit layout is simplified. In appliance systems, the ACS108 switch intends to drive low power load in full cycle ON/OFF mode. The turn off commutation characteristics of these loads can be classified in 3 groups as shown in Table 1. Thanks to its thermal and turn-off commutation characteristics, the ACS108 switch drives a load, such as door lock, lamp, relay, valve and micro motor, up to 0.2 A without any turn-off aid circuit. Switching off the ACS within one full AC line cycle will extend its current up to 0.8 A on resistive load. Table 1: Load grouping versus their turn off commutation requirement (230V AC applications). LOAD Door lock, lamp Relay Valve Dispenser Micro-motor Pump Fan (dI/dt)c (dV/dt)c (A/ms) (V/µs) TURN-OFF DELAY (ms) 1 0.15 0.15 < 10 < 0.8 1 0.4 0.15 < 20 < 0.1 > 0.7 < 0.05 <5 < 10 < 0.2 > 0.2 < 0.1 < 10 < 10 < 0.6 > 0.2 < 0.3 < 10 < 20 Load IRMS current (A) POWER FACTOR < 0.3 TYPICAL APPLICATION DIAGRAM LOAD L AC MAINS L N R OUT S ACS108 ON D COM G ST 72 MCU - Vcc ® 3/8 ACS108-5Sx HIGH INDUCTIVE SWITCH-OFF OPERATION At the end of the last conduction half-cycle, the load current reaches the holding current level IH, and the ACS™ switch turns off. Because of the inductance L of the load, the current flows through the avalanche diode D and decreases linearly to zero. During this time, the voltage across the switch is limited to the clamping voltage VCL. The energy stored in the inductance of the load depends on the holding current IH and the inductance (up to 10 H); it can reach about 20 mJ and is dissipated in the clamping section that is especially designed for that purpose. Fig. 1: Turn-off operation of the ACS108 switch with an electro valve: waveform of the gate current IG, pin OUT current IOUT & voltage VOUT. Fig. 2: ACS108 switch static characteristic. IOUT IOUT (10 mA/div) VCL = 650V IH IH VOUT VCL VOUT (200V/div) Time (400µs/div) AC LINE TRANSIENT VOLTAGE RUGGEDNESS The ACS108 switch is able to safely withstand the AC line transient voltages either by clamping the low energy spikes or by breaking over under high energy shocks. The test circuit in Figure 4 is representative of the final ACS™ application and is also used to stress the ACS™ switch according to the IEC61000-4-5 standard conditions. Thanks to the load, the ACS™ switch withstands the voltage spikes up to 2 kV above the peak line voltage. It will break over safely even on resistive load where the turn-on current rise is high as shown in Figure 4. Such non-repetitive testing can be done 10 times on each AC line voltage polarity. Fig. 3: Overvoltage ruggedness test circuit for resistive and inductive loads according to IEC61000-4-5 standard. R = 150Ω, L = 5µH, VPP = 2kV. Fig. 4: Current and voltage of the ACS™ during IEC61000-4-5 standard test with a 150Ω - 10µH load & VPP = 2kV. Vout (200 V/div) R L Iout (2 A/div) OUT AC LINE & SURGE VOLTAGE GENERATOR ACSxx S VAC + V PP dI/dt = 100 A/µs ON D COM G RG= 220Ω 4/8 ® ACS108-5Sx Fig. 5: Maximum power dissipation versus RMS on-state current. Fig. 6: RMS on-state current versus ambient temperature. P(W) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 IT(RMS)(A) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 IT(RMS)(A) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 ACS108-5SA (TO92) Tamb(°C) 0 0.8 Fig. 7-1: Relative variation of thermal impedance junction to ambient versus pulse duration (ACS108-5SA) (TO-92). ACS108-5SA (TO92, Tamb=Tlead) ACS108-5SN with 5cm² copper surface under tab 10 20 30 40 50 60 90 100 110 120 130 Zth(j-a) / Rth(j-a) Zth(j-a) / Rth(j-a) 1.00 0.10 0.10 tp(s) tp(s) 1E-2 80 Fig. 7-2: Relative variation of thermal impedance junction to ambient versus pulse duration (ACS108-5SN) (SOT-223). 1.00 0.01 1E-3 70 1E-1 1E+0 1E+1 1E+2 5E+2 Fig. 8: Relative variation of gate trigger current versus junction temperature. 0.01 1E-3 1E-2 1E-1 1E+0 1E+1 1E+2 5E+2 Fig. 9: Relative variation of holding and latching current versus junction temperature. IH,IL [Tj] / IH,IL [Tj=25°C] IGT [Tj] / IGT [Tj=25°C] 2.0 3.0 1.8 2.5 1.6 1.4 2.0 1.2 1.5 1.0 0.8 1.0 0.6 0.4 0.5 0.2 Tj(°C) 0.0 -40 ® -20 0 20 40 60 80 100 120 140 0.0 -40 Tj(°C) -20 0 20 40 60 80 100 120 140 5/8 ACS108-5Sx Fig. 10: Non repetitive surge peak on-state current versus number of cycles. ITSM(A) 9 8 7 6 5 4 Tamb=25°C 3 Repetitive 2 1 Number of cycles 0 1 10 ITSM(A),I²t(A²s) 100.0 One cycle 10.0 Tj initial=25°C Non repetitive 1.0 I²t tp(ms) 100 1000 ITM(A) 5.00 1.00 0.10 Tj max.: Vto = 0.9 V Rd = 300 mΩ VTM(V) 1.0 1.2 Tj initial=25°C ITSM t=20ms Fig. 12: On-state characteristics (maximum values). 0.01 0.8 Fig. 11: Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10ms, and corresponding value of I2t. 1.4 1.6 1.8 2.0 2.2 2.4 2.6 0.1 0.01 0.10 1.00 10.00 Fig. 13: Thermal resistance junction to ambient versus copper surface under tab (Epoxy printed circuit board FR4, copper thickness: 35µm). Rth(j-a) (°C/W) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 0.0 0.5 1.0 1.5 S(Cu) (cm²) 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Fig. 14: Relative variation of critical (dl/dt)c versus junction temperature. (dI/dt)c [Tj] / (dI/dt)c [Tj=110°C] 3.0 2.5 2.0 1.5 1.0 0.5 Tj(°C) 0.0 6/8 0 10 20 30 40 50 60 70 80 90 100 110 120 ® ACS108-5Sx ORDERING INFORMATION ACS 1 08 - Switch Number AC Switch 5 S A A = TO-92 N = SOT-223 VDRM 5 = 500V -TR = SOT-223 Tape & Reel Gate Sensitivity S = 10mA ITRMS 08 = 0.8A -TR PACKAGE MECHANICAL DATA SOT-223 DIMENSIONS c A REF. Min. V A1 B e1 D PIN B1 4 DESCRIPTION 1 GATE BASE 2 DRAIN COLLECTOR 3 SOURCE EMITTER 4 DRAIN H E 1 2 Millimeters 3 e COLLECTOR A A1 B B1 c D e e1 E H V 0.02 0.60 2.90 0.24 6.30 3.30 6.70 Typ. Max. Min. 1.80 0.10 0.001 0.70 0.85 0.024 3.00 3.15 0.114 0.26 0.35 0.009 6.50 6.70 0.248 2.3 4.6 3.50 3.70 0.130 7.00 7.30 0.264 10° max Inches Typ. Max. 0.071 0.004 0.027 0.033 0.118 0.124 0.010 0.014 0.256 0.264 0.090 0.181 0.138 0.146 0.276 0.287 PACKAGE MECHANICAL DATA SOT-223 Recommended soldering pattern SOT-223 ® 7/8 ACS108-5Sx PACKAGE MECHANICAL DATA TO-92 (Plastic) DIMENSIONS REF. A a B F E D Inches Min. A B C D E F a C Millimeters Typ. Max. Min. Typ. Max. 1.35 0.053 4.70 0.185 2.54 0.100 4.40 0.173 12.70 0.500 3.70 0.146 0.45 0.017 OTHER INFORMATION Ordering type ACS108-5SA ACS108-5SA-TR ACS108-5SN Marking ACS108/5S ACS108/5S ACS1/085S Package TO-92 TO-92 SOT-223 Weight 0.2 g 0.2 g 0.12 g Base qty 2500 2000 1000 Delivery mode Bulk Tape & reel Tape & reel REVISION HISTORY Date Apr-2004 21-Jun-2005 Revision 1 2 Description of Changes First Issue Marking information updated from ACSxxxx to ACS1xxx Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com 8/8 ®