HSP061-2 2-line ESD protection for high speed lines Features ■ Flow-through routing to keep signal integrity ■ Ultralarge bandwidth: 6 GHz ■ Ultralow capacitance: 0.6 pF ■ Low leakage current: 100 nA at 25 °C ■ Extended operating junction temperature range: -40 °C to 150 °C ■ HSP061-2M6 µQFN-6L HSP061-2N4 µQFN-4L RoHS compliant Benefits ■ High ESD robustness of the equipment ■ Suitable for high density boards Figure 1. HSP061-2P6 SOT-666 Functional schematic (top view) I/O1 1 6 I/O1 VBUS GND 2 5 VBUS I/O2 I/O2 3 4 I/O2 I/O1 1 6 I/O1 GND 2 5 I/O2 3 4 Complies with following standards ■ MIL-STD 883G Method 3015-7 Class 3B: – 8 kV ■ IEC 61000-4-2 level 4: – 15 kV (air discharge) – 8 kV (contact discharge) µQFN 6 leads SOT666 I/O1 NC Applications GND I/O2 NC µQFN 4 leads The HSP061-2 series is designed to protect against electrostatic discharge on sub micron technology circuits driving: ■ HDMI 1.3 and 1.4 ■ Digital Video Interface ■ Display Port ■ USB 3.0 ■ Serial ATA ■ Ethernet ■ HMI February 2012 Description The HSP061-2 is a 2-channel ESD array with a rail to rail architecture designed specifically for the protection of high speed differential lines. The ultralow variation of the capacitance ensures very low influence on signal-skew. The large bandwidth makes it compatible with 5 Gbps. The HSP061-2P6 is housed in SOT-666. The HSP061-2M6 is packaged in µQFN-6L (1.45 x 1.0 mm) with a 500 µm pitch. The HSP061-2N4 is packaged in µQFN-4L (1.0 x 0.8 mm) with a 400 µm pitch. Doc ID 022777 Rev 1 1/12 www.st.com 12 Characteristics HSP061-2 1 Characteristics Table 1. Absolute maximum ratings Tamb = 25 °C Symbol Parameter Value IEC 61000-4-2 contact discharge 8 IEC 61000-4-2 air discharge 15 Unit VPP Peak pulse voltage Ipp Repetitive peak pulse current (8/20 µs) 3 A Tj Operating junction temperature range -40 to +150 °C Storage temperature range -65 to +150 °C 260 °C Tstg kV TL Maximum lead temperature for soldering during 10 s Table 2. Electrical characteristics Tamb = 25 °C Symbol Test conditions Min. Typ. Max. Unit VBR Breakdown voltage IR = 1 mA IRM Leakage current VRM = 3 V VCL Clamping voltage IEC 61000-4-2, +8 kV contact (IPP = 30 A), measured at 30 ns 18 Capacitance (input/output to ground) VI/O = 0 V, F = 200 to 3000 MHz, VOSC = 30 mV 0.6 0.85 pF Capacitance variation (input/output to ground) VI/O = 0 V F = 200 to 3000 MHz, VOSC = 30 mV 0.03 0.13 pF HSP061-2M6, HSP061-2P6 5.5 HSP061-2N4 6 CI/O - GND ΔCI/O - GND fC 2/12 Parameter Cut-off frequency -3 dB 6 V 100 Doc ID 022777 Rev 1 nA V GHz HSP061-2 Figure 2. Characteristics Leakage current versus junction temperature (typical values) Figure 3. S21 attenuation measurement (HSP061-2P6, HSP061-2M6) S21(db) 10.00 0.00 VR = V RM = 3 V IR (nA) - 4.00 1.00 - 8.00 0.10 - 12.00 F(Hz) Tj (°C) 0.01 25 50 Figure 4. 0 75 100 125 150 S21 attenuation measurement (HSP061-2N4) S21 (dB) - 16.00 300.0k Figure 5. 1.0M 3.0M 10.0M 30.0M 100.0M 300.0M 1.0G 3.0G Eye diagram - HDMI mask at 3.4 Gbps per channel(1) (HSP061-2P6) 250 mV/div -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 300k F (Hz) 1M 3M IO1 10M 30M 100M 300M 1G IO2 3G 49 ps/div 1. HDMI specification conditions. This information can be provided for other applications. Please contact your local ST office. Figure 6. Eye diagram - HDMI mask at 3.4 Gbps per channel(1) (HSP061-2M6) 250 mV/div Figure 7. Eye diagram - HDMI mask at 3.4 Gbps per channel(1) (HSP061-2N4) 250 mV/div 49 ps/div Doc ID 022777 Rev 1 49 ps/div 3/12 Ordering information scheme Figure 8. HSP061-2 ESD response to IEC 61000-4-2 (+8 kV contact discharge) Figure 9. ESD response to IEC 61000-4-2 (-8 kV contact discharge) 10V/Div 10V/Div 100ns/Div 100ns/Div 2 Ordering information scheme Figure 10. Ordering information scheme HSP 06 1 - 2 xx High speed line protection Breakdown voltage Version Number of lines Package P6 = SOT-666 M6 = µQFN-6L N4 = µQFN-4L 4/12 Doc ID 022777 Rev 1 HSP061-2 3 Package information Package information ● Epoxy meets UL94, V0 ● Lead-free package In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 3. SOT-666 dimensions Dimensions b1 Ref. L1 Millimeters Min. L3 Typ. Max. Inches Min. Typ. Max. A 0.45 0.60 0.018 0.024 A3 0.08 0.18 0.003 0.007 b 0.17 0.34 0.007 0.013 b1 0.19 D 1.50 1.70 0.059 0.067 E 1.50 1.70 0.059 0.067 E1 1.10 1.30 0.043 0.051 b D E1 A L2 E A3 0.27 0.34 0.007 0.011 0.013 e 0.50 0.020 L1 0.19 0.007 L2 0.10 0.30 0.004 0.012 e L3 Figure 11. Footprint recommendations dimensions in mm (inches) 0.10 0.004 Figure 12. Marking 0.50 (0.019) 0.62 2.60 (0.024) (0.01) R 0.99 (0.039) 0.30 (0.012) Doc ID 022777 Rev 1 5/12 Package information HSP061-2 Table 4. µQFN 1.45x1.00 6L dimensions Dimensions 1 2 L Ref. k b e A A1 D N E 1 2 Figure 13. Footprint recommendations dimensions in mm (inches) 0.50 [0.020] Typ. Max. Min. Typ. A 0.50 0.55 0.60 0.020 0.022 0.024 A1 0.00 0.02 0.05 0.000 0.001 0.002 b 0.18 0.25 0.30 0.007 0.010 0.012 D 1.45 0.057 E 1.00 0.039 e 0.50 0.020 K 0.20 L 0.30 Max. 0.008 0.35 0.40 0.012 0.014 0.016 Figure 14. Marking 0.25 [0.010] 0.30 [0.012] 6/12 Inches Min. 0.65 [0.026] Note: Millimeters 1.60 [0.063] T Product marking may be rotated by 90° for assembly plant differentiation. In no case should this product marking be used to orient the component for its placement on a PCB. Only pin 1 mark is to be used for this purpose. Doc ID 022777 Rev 1 HSP061-2 Package information Table 5. µQFN-4L dimensions Dimensions Ref. Side view Millimeters Inches Min. Typ. Max. Min. Typ. Max. A 0.45 0.50 0.55 0.018 0.020 0.022 A1 0.00 0.02 0.05 0.000 0.001 0.002 b 0.15 0.20 0.25 0.006 0.008 0.010 D 0.75 0.80 0.85 0.030 0.031 0.033 D2 0.55 0.6 0.65 0.022 0.024 0.026 e 0.35 0.40 0.45 0.014 0.016 0.018 E 0.95 1.00 1.05 0.037 0.039 0.041 E2 0.15 0.20 0.25 0.006 0.008 0.010 k 0.17 0.20 0.23 0.007 0.008 0.009 L 0.15 0.20 0.25 0.006 0.008 0.010 A A1 D D2 e Bottom view k E2 E L b Figure 15. Footprint recommendations (dimensions in mm) Figure 16. Marking 0.4 (0.016) Pin 1 0.4 (0.016) 0.2 (0.008) 0.2 (0.008) 1.4 (0.055) 1 0.6 (0.024) Note: Product marking may be rotated by 90° for assembly plant differentiation. In no case should this product marking be used to orient the component for its placement on a PCB. Only pin 1 mark is to be used for this purpose. Doc ID 022777 Rev 1 7/12 Recommendation on PCB assembly HSP061-2 4 Recommendation on PCB assembly 4.1 Stencil opening design 1. General recommendation on stencil opening design a) Stencil opening dimensions: L (Length), W (Width), T (Thickness). Figure 17. Stencil opening dimensions L T b) W General design rule Stencil thickness (T) = 75 ~ 125 µm W Aspect Ratio = ----- ≥ 1.5 T L×W Aspect Area = ---------------------------- ≥ 0.66 2T ( L + W ) 2. Reference design a) Stencil opening thickness: 100 µm b) Stencil opening for leads: Opening to footprint ratio is 90%. Figure 18. Recommended stencil window position for µQFN-6L 7 µm 7 µm 620 µm 650 µm 15 µm 236 µm 15 µm Footprint 250 µm Stencil window Footprint 8/12 Doc ID 022777 Rev 1 HSP061-2 Recommendation on PCB assembly Figure 19. Recommended stencil window position for µQFN-4L T=100 µm and opening ratio is 100% 430 µm 0.4 0.4 0.2 0.2 1.4 0.6 180 µm 580 µm 0.6 200 µm Footprint Stencil windo w Footprint 4.2 4.3 Solder paste 1. Halide-free flux qualification ROL0 according to ANSI/J-STD-004. 2. “No clean” solder paste is recommended. 3. Offers a high tack force to resist component movement during high speed. 4. Solder paste with fine particles: powder particle size is 20-45 µm. Placement 1. Manual positioning is not recommended. 2. It is recommended to use the lead recognition capabilities of the placement system, not the outline centering. 3. Standard tolerance of ± 0.05 mm is recommended. Doc ID 022777 Rev 1 9/12 Recommendation on PCB assembly 4.4 4.5 HSP061-2 4. 3.5 N placement force is recommended. Too much placement force can lead to squeezed out solder paste and cause solder joints to short. Too low placement force can lead to insufficient contact between package and solder paste that could cause open solder joints or badly centered packages. 5. To improve the package placement accuracy, a bottom side optical control should be performed with a high resolution tool. 6. For assembly, a perfect supporting of the PCB (all the more on flexible PCB) is recommended during solder paste printing, pick and place and reflow soldering by using optimized tools. PCB design preference 1. To control the solder paste amount, the closed via is recommended instead of open vias. 2. The position of tracks and open vias in the solder area should be well balanced. The symmetrical layout is recommended, in case any tilt phenomena caused by asymmetrical solder paste amount due to the solder flow away. Reflow profile Figure 20. ST ECOPACK® recommended soldering reflow profile for PCB mounting Temperature (°C) 260°C max 255°C 220°C 180°C 125 °C 2°C/s recommended 2°C/s recommended 6°C/s max 6°C/s max 3°C/s max 3°C/s max 0 0 1 2 3 4 5 10-30 sec 90 to 150 sec Note: 10/12 6 7 Time (min) 90 sec max Minimize air convection currents in the reflow oven to avoid component movement. Doc ID 022777 Rev 1 HSP061-2 5 Ordering information Ordering information Table 6. Ordering information Order code Marking Package Weight Base qty Delivery mode HSP061-2P6 R SOT-666 2.85 mg 3000 Tape and reel (7”) HSP061-2M6 (1) µQFN-6L 2.3 mg 3000 Tape and reel (7”) (1) µQFN-4L 1.17 mg 10000 Tape and reel (7”) T HSP061-2N4 1 1. The marking can be rotated by multiple of 90° to differentiate assembly location 6 Revision history Table 7. Document revision history Date Revision 07-Feb-2012 1 Changes Initial release. Doc ID 022777 Rev 1 11/12 HSP061-2 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12 Doc ID 022777 Rev 1