CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 A USB-Enabled System-On-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee Applications Check for Samples: CC2531F128, CC2531F256 FEATURES 1 • RF/Layout – 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver – Excellent Receiver Sensitivity and Robustness to Interference – Programmable Output Power Up to 4.5 dBm – Few External Components – Only a Single Crystal Needed for Asynchronous Networks – 6-mm × 6-mm QFN40 Package – Suitable for Systems Targeting Compliance With Worldwide Radio-Frequency Regulations: ETSI EN 300 328 and EN 300 440 (Europe), FCC CFR47 Part 15 (US), and ARIB STD-T-66 (Japan) • USB – USB 2.0 Certified Full Speed Device (12 Mbps) – 5 Highly Flexible Endpoints – 1-KB Dedicated FIFO – DMA Access to FIFO – No 48-MHz Crystal Required • Low Power – Active Mode RX (CPU Idle): 24 mA – Active Mode TX at 1 dBm (CPU Idle): 29 mA – Power Mode 1 (4 ms Wake-Up): 0.2 mA – Power Mode 2 (Sleep Timer Running): 1 mA – Power Mode 3 (External Interrupts): 0.4 mA – Wide Supply-Voltage Range (2 V–3.6 V) • Microcontroller 2345 • • – High-Performance and Low-Power 8051 Microcontroller Core With Code Prefetch – 256-KB or 128-KB In-System-Programmable Flash – 8-KB RAM With Retention in All Power Modes – Hardware Debug Support Peripherals – Powerful Five-Channel DMA – IEEE 802.15.4 MAC Timer, General-Purpose Timers (One 16-Bit, Two 8-Bit) – IR Generation Circuitry – 32-kHz Sleep Timer With Capture – CSMA/CA Hardware Support – Accurate Digital RSSI/LQI Support – Battery Monitor and Temperature Sensor – 12-Bit ADC With Eight Channels and Configurable Resolution – AES Security Coprocessor – Two Powerful USARTs With Support for Several Serial Protocols – 21 General-Purpose I/O Pins (19 × 4 mA, 2 × 20 mA) – Watchdog Timer Development Tools – CC2531 Development Kit – Certified CC2531 USB Dongle Reference Design – SmartRF™ Software – Packet Sniffer – IAR Embedded Workbench® Software Available 1 2 3 4 5 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SmartRF, Z-Stack, RemoTI are trademarks of Texas Instruments. IAR Embedded Workbench is a registered trademark of IAR Systems AB. ZigBee is a registered trademark of ZigBee Alliance. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009–2010, Texas Instruments Incorporated CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com APPLICATIONS • • • • • • • • • • USB Upgradable 2.4-GHz IEEE 802.15.4 Systems RF4CE Remote Control Target for TV or STB PC Peripherals ZigBee® Systems Home/Building Automation Lighting Systems Industrial Control and Monitoring Low-Power Wireless Sensor Networks Consumer Electronics Health Care This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. DESCRIPTION The CC2531 is a USB enabled true system-on-chip (SoC) solution for IEEE 802.15.4, ZigBee and RF4CE applications. It enables USB dongles or USB upgradable network nodes to be built with low total bill-of-material costs. The CC2531 combines the performance of a leading RF transceiver with an industry-standard enhanced 8051 MCU, in-system programmable flash memory, 8-KB RAM, and many other powerful features. The CC2531 has various operating modes, making it suited for systems where ultralow power consumption is required. Short transition times between operating modes further ensure low energy consumption. Source code for USB HID and CDC libraries and examples are downloadable from the CC2531 product page on www.ti.com. Combined with the industry-leading and golden-unit-status ZigBee protocol stack ( Z-Stack™) from Texas Instruments, the CC2531 provides a robust and complete ZigBee USB dongle or firmware upgradable network node. Combined with the golden-unit-status RemoTI™ stack from Texas Instruments, the CC2531 provides a robust ZigBee RF4CE remote-control target for USB dongle or TV/STB implementations. 2 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 VDD (2 V–3.6 V) RESET WATCHDOG TIMER ON-CHIP VOLTAGE REGULATOR 32-MHz CRYSTAL OSC HIGH-SPEED RC-OSC POWER ON RESET BROWN OUT 32.768-kHz CRYSTAL OSC 32-kHz RC-OSC SLEEP TIMER DEBUG INTERFACE CLOCK MUX and CALIBRATION SLEEP MODE CONTROLLER 1-KB USB FIFO USB DIGITAL DCOUPL ANALOG MIXED RESET_N XOSC_Q2 XOSC_Q1 P2_4 P2_3 DP DM USB PHY P2_2 128/256-KB FLASH P2_1 P2_0 8051 CPU CORE DMA MEMORY ARBITRATOR P1_6 P1_5 P1_4 P1_3 P1_2 I/O CONTROLLER P1_7 P1_1 P1_0 8-KB SRAM IRQ CTRL ADC AUDIO/DC 8 CHANNELS AES ENCRYPTION AND DECRYPTION FLASH WRITE RADIO REGISTERS CSMA/CA STROBE PROCESSOR P0_7 P0_5 USART 1 RADIO DATA INTERFACE P0_4 P0_3 USART 2 P0_2 DEMODULATOR AGC MODULATOR P0_1 TIMER 1 (16-Bit) P0_0 TIMER 3 (8-Bit) TIMER 4 (8-Bit) RECEIVE CHAIN FREQUENCY SYNTHESIZER TIMER 2 (IEEE 802.15.4 MAC TIMER) RF_P FIFO and FRAME CONTROL P0_6 TRANSMIT CHAIN RF_N B0300-02 ABSOLUTE MAXIMUM RATINGS (1) Supply voltage MIN MAX –0.3 3.9 V –0.3 VDD + 0.3, ≤ 3.9 V 10 dBm –40 125 °C All pads, according to human-body model, JEDEC STD 22, method A114 2 kV According to charged-device model, JEDEC STD 22, method C101 500 V All supply pins must have the same voltage Voltage on any digital pin Input RF level Storage temperature range ESD (2) (1) (2) UNIT Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. CAUTION: ESD-sensitive device. Precautions should be used when handling the device in order to prevent permanent damage. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 3 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com RECOMMENDED OPERATING CONDITIONS MIN MAX UNIT –40 125 °C 2 3.6 V Operating ambient temperature range, TA Operating supply voltage ELECTRICAL CHARACTERISTICS Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. Boldface limits apply over the entire operating range, TA = –40°C to 125°C, VDD = 2 V to 3.6 V, and fc = 2394 MHz to 2507 MHz. PARAMETER Icore TEST CONDITIONS Core current consumption MIN TYP MAX UNIT Digital regulator on. 16-MHz RCOSC running. No radio, crystals, or peripherals active. Medium CPU activity: normal flash access (1), no RAM access 3.4 32-MHz XOSC running. No radio or peripherals active. Medium CPU activity: normal flash access (1), no RAM access 6.5 mA 8.9 mA 32-MHz XOSC running, radio in RX mode, –50-dBm input power, no peripherals active, CPU idle 20.5 32-MHz XOSC running, radio in RX mode at –100-dBm input power (waiting for signal), no peripherals active, CPU idle 24.3 32-MHz XOSC running, radio in TX mode, 1-dBm output power, no peripherals active, CPU idle 28.7 32-MHz XOSC running, radio in TX mode, 4.5-dBm output power, no peripherals active, CPU idle 33.5 39.6 mA 0.2 0.3 mA Power mode 2. Digital regulator off; 16-MHz RCOSC and 32-MHz crystal oscillator off; 32.768-kHz XOSC, POR, and sleep timer active; RAM and register retention 1 2 mA Power mode 3. Digital regulator off; no clocks; POR active; RAM and register retention 0.4 1 mA Power mode 1. Digital regulator on; 16-MHz RCOSC and 32-MHz crystal oscillator off; 32.768-kHz XOSC, POR, BOD and sleep timer active; RAM and register retention mA 29.6 mA mA Peripheral Current Consumption (Adds to core current Icore for each peripheral unit activated) Iperi Timer 1 Timer running, 32-MHz XOSC used 90 mA Timer 2 Timer running, 32-MHz XOSC used 90 mA Timer 3 Timer running, 32-MHz XOSC used 60 mA Timer 4 Timer running, 32-MHz XOSC used 70 mA Sleep timer Including 32.753-kHz RCOSC 0.6 mA USB Measured on CC2531 dongle reference design, 48-MHz clock running, USB enabled 0.1 mA ADC When converting Flash (1) 1.2 mA Erase 1 mA Burst write peak current 6 mA Normal flash access means that the code used exceeds the cache storage, so cache misses happen frequently. GENERAL CHARACTERISTICS Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT WAKE-UP AND TIMING Power mode 1 → active Digital regulator on, 16-MHz RCOSC and 32-MHz crystal oscillator off. Start-up of 16-MHz RCOSC 4 ms Power mode 2 or 3 → active Digital regulator off, 16-MHz RCOSC and 32-MHz crystal oscillator off. Start-up of regulator and 16-MHz RCOSC 0.1 ms Initially running on 16-MHz RCOSC, with 32-MHz XOSC off 0.5 Active → TX or RX 4 With 32-MHz XOSC initially on Submit Documentation Feedback ms 192 ms Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 GENERAL CHARACTERISTICS (continued) Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP RX/TX and TX/RX turnaround USB PLL start-up time With 32-MHz XOSC initially on MAX UNIT 192 ms 32 ms RADIO PART RF frequency range Programmable in 1-MHz steps, 5 MHz between channels for compliance with [1] Radio baud rate As defined by [1] 250 Radio chip rate As defined by [1] 2 2394 2507 Flash erase cycles kbps MChip/s 20 Flash page size MHz k Cycles 2 Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback KB 5 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com RF RECEIVE SECTION Measured on Texas Instruments CC2530 EM reference design with TA = 25°C, VDD = 3 V, and fc = 2440 MHz, unless otherwise noted. Bold limits apply over the entire operating range, TA = –40°C to 125°C, VDD = 2 V to 3.6 V, and fc = 2394 MHz to 2507 MHz. PARAMETER Receiver sensitivity TEST CONDITIONS MIN PER = 1%, as specified by [1] TYP MAX –97 [1] requires –85 dBm –92 –88 UNIT dBm Saturation (maximum input level) PER = 1%, as specified by [1] [1] requires –20 dBm 10 dBm Adjacent-channel rejection, 5-MHz channel spacing Wanted signal –82 dBm, adjacent modulated channel at 5 MHz, PER = 1%, as specified by [1]. [1] requires 0 dB 49 dB Adjacent-channel rejection, –5-MHz channel spacing Wanted signal –82 dBm, adjacent modulated channel at –5 MHz, PER = 1%, as specified by [1]. [1] requires 0 dB 49 dB Alternate-channel rejection, 10-MHz channel spacing Wanted signal –82 dBm, adjacent modulated channel at 10 MHz, PER = 1%, as specified by [1] [1] requires 30 dB 57 dB Alternate-channel rejection, –10-MHz channel spacing Wanted signal –82 dBm, adjacent modulated channel at –10 MHz, PER = 1%, as specified by [1] [1] requires 30 dB 57 dB 57 57 dB –3 dB Channel rejection ≥ 20 MHz ≤ –20 MHz Co-channel rejection Wanted signal at –82 dBm. Undesired signal is an IEEE 802.15.4 modulated channel, stepped through all channels from 2405 to 2480 MHz. Signal level for PER = 1%. Wanted signal at –82 dBm. Undesired signal is 802.15.4 modulated at the same frequency as the desired signal. Signal level for PER = 1%. Blocking/desensitization 5 MHz from band edge 10 MHz from band edge 20 MHz from band edge 50 MHz from band edge –5 MHz from band edge –10 MHz from band edge –20 MHz from band edge –50 MHz from band edge Wanted signal 3 dB above the sensitivity level, CW jammer, PER = 1%. Measured according to EN 300 440 class 2. Spurious emission. Only largest spurious Conducted measurement with a 50-Ω single-ended load. emission stated within each band. Suitable for systems targeting compliance with EN 300 328, 30 MHz–1000 MHz EN 300 440, FCC CFR47 Part 15, and ARIB STD-T-66. 1 GHz–12.75 GHz –33 –33 –32 –31 –35 –35 –34 –34 ≤80 –57 dBm dBm Frequency error tolerance (1) [1] requires minimum 80 ppm ±150 ppm Symbol rate error tolerance (2) [1] requires minimum 80 ppm ±1000 ppm Sensitivity impact of USB operation Measured on CC2531 dongle reference design with CDC bulk transfer to PC at maximum speed (1) (2) 6 0.5 dB Difference between center frequency of the received RF signal and local oscillator frequency Difference between incoming symbol rate and the internally generated symbol rate Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 RF TRANSMIT SECTION Measured on Texas Instruments CC2530 EM reference design with TA = 25°C, VDD = 3 V and fc = 2440 MHz, unless otherwise noted. Boldface limits apply over the entire operating range, TA = –40°C to 125°C, VDD = 2 V to 3.6 V, and fc = 2394 MHz to 2507 MHz. PARAMETER Nominal output power TEST CONDITIONS MIN Delivered to a single-ended 50-Ω load through a balun using maximum-recommended output-power setting 0 [1] requires minimum –3 dBm dBm 10 –60 –60 –60 –57 –55 –42 –31 –53 dB dBm –42 Error vector magnitude (EVM) Optimum load impedance Differential impedance as seen from the RF port (RF_P and RF_N) towards the antenna (3) 8 UNIT Max recommended output power setting (1) Measured according to stated regulations. Measured as defined by [1] using maximum-recommended output-power setting [1] requires maximum 35%. (2) MAX 32 Only largest spurious emission 25 MHz–1000 MHz (outside restricted bands) stated within each band. 25 MHz–2400 MHz (within FCC restricted bands) 25 MHz–1000 MHz (within ETSI restricted bands) 1800–1900 MHz (ETSI restricted band) 5150–5300 MHz (ETSI restricted band) At 2 × fc and 3 × fc (FCC restricted band) At 2 × fc and 3 × fc (ETSI EN 300-440 and EN 300-328) (2) 1 GHz–12.75 GHz (outside restricted bands) At 2483.5 MHz and above (FCC restricted band) fc= 2480 MHz (3) (1) 4.5 –8 Programmable output power range Spurious emissions TYP 2% 69 + j29 Ω Texas Instruments CC2530 EM reference design is suitable for systems targeting compliance with EN 300 328, EN 300 440, FCC CFR47 Part 15, and ARIB STD-T-66. Margins for passing conducted requirements at the third harmonic can be improved by using a simple band-pass filter connected between matching network and RF connector (1.8 pF in parallel with 1.6 nH); this filter must be connected to a good RF ground. Margins for passing FCC requirements at 2483.5 MHz and above when transmitting at 2480 MHz can be improved by using a lower output-power setting or having less than 100% duty cycle. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 7 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com 32-MHz CRYSTAL OSCILLATOR Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN Crystal frequency TYP MAX 32 Crystal frequency accuracy requirement (1) UNIT MHz –40 40 ppm ESR Equivalent series resistance 6 60 Ω C0 Crystal shunt capacitance 1 7 pF CL Crystal load capacitance 10 16 pF Start-up time 0.3 The crystal oscillator must be in power down for a guard time before it is used again. This requirement is valid for all modes of operation. The need for power-down guard time can vary with crystal type and load. Power-down guard time (1) ms 3 ms Including aging and temperature dependency, as specified by [1] 32.768-kHz CRYSTAL OSCILLATOR Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN Crystal frequency TYP MAX 32.768 Crystal frequency accuracy requirement (1) –40 UNIT kHz 40 ppm ESR Equivalent series resistance 40 130 kΩ C0 Crystal shunt capacitance 0.9 2 pF CL Crystal load capacitance 12 16 pF Start-up time 0.4 (1) s Including aging and temperature dependency, as specified by [1] 32-kHz RC OSCILLATOR Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP Calibrated frequency (1) 32.753 Frequency accuracy after calibration ±0.2% Temperature coefficient (2) MAX UNIT kHz 0.4 %/°C Supply-voltage coefficient (3) 3 %/V Calibration time (4) 2 ms (1) (2) (3) (4) 8 The calibrated 32-kHz RC oscillator frequency is the 32-MHz XTAL frequency divided by 977. Frequency drift when temperature changes after calibration Frequency drift when supply voltage changes after calibration When the 32-kHz RC oscillator is enabled, it is calibrated when a switch from the 16-MHz RC oscillator to the 32-MHz crystal oscillator is performed while SLEEPCMD.OSC32K_CALDIS is 0. Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 16-MHz RC OSCILLATOR Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP Frequency (1) MAX Uncalibrated frequency accuracy ±18% Calibrated frequency accuracy ±0.6% MHz ±1% Start-up time 10 Initial calibration time (2) (1) (2) UNIT 16 ms 50 ms The calibrated 16-MHz RC oscillator frequency is the 32-MHz XTAL frequency divided by 2. When the 16-MHz RC oscillator is enabled, it is calibrated when a switch from the 16-MHz RC oscillator to the 32-MHz crystal oscillator is performed while SLEEPCMD.OSC_PD is set to 0. RSSI/CCA CHARACTERISTICS Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN RSSI range TYP MAX UNIT 100 dB Absolute uncalibrated RSSI/CCA accuracy ±4 dB RSSI/CCA offset (1) 73 dB 1 dB Step size (LSB value) (1) Real RSSI = Register value – offset FREQEST CHARACTERISTICS Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN FREQEST range TYP MAX UNIT ±250 kHz FREQEST accuracy ±40 kHz FREQEST offset (1) 20 kHz Step size (LSB value) 7.8 kHz (1) Real FREQEST = Register value – offset FREQUENCY SYNTHESIZER CHARACTERISTICS Measured on Texas Instruments CC2530 EM reference design with TA = 25°C, VDD = 3 V and fc = 2440 MHz, unless otherwise noted. PARAMETER Phase noise, unmodulated carrier TEST CONDITIONS MIN TYP At ±1-MHz offset from carrier –110 At ±2-MHz offset from carrier –117 At ±5-MHz offset from carrier –122 MAX UNIT dBc/Hz ANALOG TEMPERATURE SENSOR Measured on Texas Instruments CC2530 EM reference design with TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS Output at 25°C MIN TYP 1480 Temperature coefficient 4.5 Voltage coefficient Measured using integrated ADC, using internal bandgap voltage reference and maximum resolution Initial accuracy without calibration Accuracy using 1-point calibration (entire temperature range) Current consumption when enabled (ADC current not included) Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 1 MAX UNIT 12-bit ADC /1°C /0.1 V ±10 °C ±5 °C 0.5 mA Submit Documentation Feedback 9 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com ADC CHARACTERISTICS TA = 25°C and VDD = 3 V, unless otherwise noted. PARAMETER ENOB (1) MIN TYP MAX Input voltage VDD is voltage on AVDD5 pin TEST CONDITIONS 0 VDD V External reference voltage VDD is voltage on AVDD5 pin 0 VDD V External reference voltage differential VDD is voltage on AVDD5 pin 0 VDD V Input resistance, signal Using 4-MHz clock speed 197 kΩ Full-scale signal (1) Peak-to-peak, defines 0 dBFS 2.97 V Effective number of bits Total harmonic distortion Single-ended input, 9-bit setting 7.5 Single-ended input, 10-bit setting 9.3 Single-ended input, 12-bit setting 10.8 6.5 Differential input, 9-bit setting 8.3 Differential input, 10-bit setting 10.0 Differential input, 12-bit setting 11.5 7-bit setting, both single and differential 0–20 Single-ended input, 12-bit setting, –6 dBFS –75.2 Differential input, 12-bit setting, –6 dBFS –86.6 79.3 Single-ended input, 12-bit setting, –6 dBFS 78.8 Differential input, 12-bit setting, –6 dBFS 88.9 Common-mode rejection ratio Differential input, 12-bit setting, 1-kHz sine (0 dBFS), limited by ADC resolution >84 dB Crosstalk Single-ended input, 12-bit setting, 1-kHz sine (0 dBFS), limited by ADC resolution >84 dB Offset Midscale –3 mV Differential nonlinearity INL (1) Integral nonlinearity dB 0.68% 12-bit setting, mean 0.05 12-bit setting, maximum 0.9 12-bit setting, mean (1) Signal-to-noise-and-distortion Conversion time 4.6 12-bit setting, maximum 13.3 Single-ended input, 7-bit setting 35.4 Single-ended input, 9-bit setting 46.8 Single-ended input, 10-bit setting 57.5 Single-ended input, 12-bit setting 66.6 Differential input, 7-bit setting 40.7 Differential input, 9-bit setting 51.6 Differential input, 10-bit setting 61.8 Differential input, 12-bit setting 70.8 7-bit setting 20 9-bit setting 36 10-bit setting 68 12-bit setting 132 Power consumption 1.2 Internal reference voltage 1.15 Internal reference VDD coefficient 4 Internal reference temperature coefficient 10 dB 70.2 DNL (1) (1) kHz Differential input, 12-bit setting Gain error SINAD (–THD+N) bits Single-ended input, 12-bit setting Signal to nonharmonic ratio (1) CMRR 5.7 Differential input, 7-bit setting Useful power bandwidth THD (1) Single-ended input, 7-bit setting UNIT 0.4 LSB LSB dB ms mA V mV/V mV/10°C Measured with 300-Hz sine-wave input and VDD as reference. Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 CONTROL INPUT AC CHARACTERISTICS TA = –40°C to 125°C, VDD = 2 V to 3.6 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 32 MHz System clock, fSYSCLK tSYSCLK = 1/fSYSCLK The undivided system clock is 32 MHz when crystal oscillator is used. The undivided system clock is 16 MHz when calibrated 16-MHz RC oscillator is used. 16 RESET_N low duration See item 1, Figure 1. This is the shortest pulse that is recognized as a complete reset pin request. Note that shorter pulses may be recognized but might not lead to complete reset of all modules within the chip. 1 ms Interrupt pulse duration See item 2, Figure 1.This is the shortest pulse that is recognized as an interrupt request. 20 ns RESET_N 1 2 Px.n T0299-01 Figure 1. Control Input AC Characteristics Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 11 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com SPI AC CHARACTERISTICS TA = –40°C to 125°C, VDD = 2 V to 3.6 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX 250 UNIT SCK period Master, RX and TX SCK duty cycle Master ns t2 SSN low to SCK Master 63 t3 SCK to SSN high Master 63 t4 MOSI early out Master, load = 10 pF 7 ns t5 MOSI late out Master, load = 10 pF 10 ns t6 MISO setup Master 90 ns t7 MISO hold Master 10 ns t1 SCK period Slave, RX and TX 250 ns 50% ns ns SCK duty cycle Slave t2 SSN low to SCK Slave 63 t3 SCK to SSN high Slave 63 t8 MISO early out Slave, load = 10 pF t9 MISO late out Slave, load = 10 pF t10 MOSI setup Slave 35 ns t11 MOSI hold Slave 10 ns Operating frequency 50% ns ns 0 ns 95 ns Master, TX only 8 Master, RX and TX 4 Slave, RX only 8 Slave, RX and TX 4 MHz SCK t2 t3 SSN t4 D0 MOSI t6 MISO X t5 X D1 t7 D0 X T0478-01 Figure 2. SPI Master AC Characteristics 12 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 SCK t2 t3 SSN t8 D0 MISO X t10 MOSI X t9 D1 t11 D0 X T0479-01 Figure 3. SPI Slave AC Characteristics Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 13 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com DEBUG INTERFACE AC CHARACTERISTICS TA = –40°C to 125°C, VDD = 2 V to 3.6 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 12 MHz fclk_dbg Debug clock frequency (see Figure 4) t1 Allowed high pulse on clock (see Figure 4) 35 ns t2 Allowed low pulse on clock (see Figure 4) 35 ns t3 EXT_RESET_N low to first falling edge on debug clock (see Figure 5) 167 ns t4 Falling edge on clock to EXT_RESET_N high (see Figure 5) 83 ns t5 EXT_RESET_N high to first debug command (see Figure 5) 83 ns t6 Debug data setup (see Figure 6) 2 ns t7 Debug data hold (see Figure 6) t8 Clock-to-data delay (see Figure 6) 4 Load = 10 pF ns 30 ns Time DEBUG_ CLK P2_2 t1 t2 1/fclk_dbg T0436-01 Figure 4. Debug Clock – Basic Timing Time DEBUG_ CLK P2_2 RESET_N t3 t4 t5 T0437-01 Figure 5. Data Setup and Hold Timing 14 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 Time DEBUG_ CLK P2_2 DEBUG_DATA (to CC2531) P2_1 DEBUG_DATA (from CC2531) P2_1 t6 t8 t7 T0438-01 Figure 6. Debug Enable Timing TIMER INPUTS AC CHARACTERISTICS TA = –40°C to 125°C, VDD = 2 V to 3.6 V, unless otherwise noted. PARAMETER Input capture pulse duration TEST CONDITIONS MIN Synchronizers determine the shortest input pulse that can be recognized. The synchronizers operate at the current system clock rate (16 or 32 MHz). TYP MAX UNIT tSYSCLK 1.5 DC CHARACTERISTICS TA = 25°C, VDD = 3 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP Logic-0 input voltage MAX UNIT 0.5 Logic-1 input voltage V 2.5 V Logic-0 input current Input equals 0 V –50 50 Logic-1 input current Input equals VDD –50 50 I/O-pin pullup and pulldown resistors nA nA 20 Logic-0 output voltage, 4-mA pins Output load 4 mA Logic-1 output voltage, 4-mA pins Output load 4 mA Logic-0 output voltage, 20-mA pins Output load 20 mA Logic-1 output voltage, 20-mA pins Output load 20 mA kΩ 0.5 V 2.4 V 0.5 V 2.4 V USB INTERFACE DC CHARACTERISTICS TA = 25°C, VDD = 3 V to 3.6 V, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT USB pad voltage output, high VDD 3.6 V, 4-mA load 3.4 V USB pad voltage output, low VDD 3.6 V, 4-mA load 0.2 V Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 15 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com DEVICE INFORMATION DVDD1 P1_6 P1_7 P2_0 P2_1 P2_2 P2_3/XOSC32K_Q2 P2_4/XOSC32K_Q1 40 39 38 37 36 35 34 33 32 AVDD6 DCOUPL RHA PACKAGE (TOP VIEW) 31 30 RBIAS 2 29 AVDD4 1 USB_P USB_N 3 28 AVDD1 DVDD_USB 4 27 AVDD2 P1_5 5 26 RF_N P1_4 6 25 RF_P P1_3 7 24 AVDD3 P1_2 8 23 XOSC_Q2 9 DGND_USB 22 14 15 16 17 18 19 P0_4 P0_3 P0_2 P0_1 P0_0 21 20 XOSC_Q1 AVDD5 RESET_N 13 P0_5 12 P0_6 10 11 P0_7 DVDD2 P1_0 P1_1 GND Ground Pad NOTE: The exposed ground pad must be connected to a solid ground plane, as this is the ground connection for the chip. Pin Descriptions PIN NAME PIN PIN TYPE DESCRIPTION AVDD1 28 Power (analog) 2-V–3.6-V analog power-supply connection AVDD2 27 Power (analog) 2-V–3.6-V analog power-supply connection AVDD3 24 Power (analog) 2-V–3.6-V analog power-supply connection AVDD4 29 Power (analog) 2-V–3.6-V analog power-supply connection AVDD5 21 Power (analog) 2-V–3.6-V analog power-supply connection AVDD6 31 Power (analog) 2-V–3.6-V analog power-supply connection DCOUPL 40 Power (digital) 1.8-V digital power-supply decoupling. Do not use for supplying external circuits. DGND_USB 1 Ground (USB pads) USB Ground DVDD1 39 Power (digital) 2-V–3.6-V digital power-supply connection DVDD2 10 Power (digital) 2-V–3.6-V digital power-supply connection DVDD_USB 4 Power (USB Pads) 3.3V USB power supply connection GND — Ground The ground pad must be connected to a solid ground plane. P0_0 19 Digital I/O Port 0.0 P0_1 18 Digital I/O Port 0.1 P0_2 17 Digital I/O Port 0.2 P0_3 16 Digital I/O Port 0.3 P0_4 15 Digital I/O Port 0.4 P0_5 14 Digital I/O Port 0.5 16 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 Pin Descriptions (continued) PIN NAME PIN PIN TYPE DESCRIPTION P0_6 13 Digital I/O Port 0.6 P0_7 12 Digital I/O Port 0.7 P1_0 11 Digital I/O Port 1.0 – 20-mA drive capability P1_1 9 Digital I/O Port 1.1 – 20-mA drive capability P1_2 8 Digital I/O Port 1.2 P1_3 7 Digital I/O Port 1.3 P1_4 6 Digital I/O Port 1.4 P1_5 5 Digital I/O Port 1.5 P1_6 38 Digital I/O Port 1.6 P1_7 37 Digital I/O Port 1.7 P2_0 36 Digital I/O Port 2.0 P2_1 35 Digital I/O Port 2.1 P2_2 34 Digital I/O Port 2.2 P2_3/ XOSC32K_Q2 33 Digital I/O, analog I/O Port 2.3/32.768 kHz XOSC P2_4/ XOSC32K_Q1 32 Digital I/O, analog I/O Port 2.4/32.768 kHz XOSC RBIAS 30 Analog I/O External precision bias resistor for reference current RESET_N 20 Digital input Reset, active-low RF_N 26 RF I/O Negative RF input signal to LNA during RX Negative RF output signal from PA during TX RF I/O Positive RF input signal to LNA during RX Positive RF output signal from PA during TX 3 USB I/O USB differential data minus (D–) USB_P 2 USB I/O USB differential data plus (D+) XOSC_Q1 22 Analog I/O 32-MHz crystal oscillator pin 1 or external-clock input XOSC_Q2 23 Analog I/O 32-MHz crystal oscillator pin 2 RF_P USB_N 25 Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 17 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com CIRCUIT DESCRIPTION VDD (2.0 - 3.6 V) ON-CHIP VOLTAGE REGULATOR RESET_N RESET XOSC_Q2 POWER-ON RESET BROWN OUT WATCHDOG TIMER 32-MHz CRYSTAL OSC XOSC_Q1 32.768-kHz CRYSTAL OSC P2_4 P2_3 DCOUPL SLEEP TIMER CLOCK MUX and CALIBRATION POWER MGT. CONTROLLER 1-KB FIFO SRAM P2_2 DEBUG INTERFACE P2_1 HIGH-SPEED RC-OSC 32-kHz RC-OSC USB DP USB PHY DM P2_0 8-KB SRAM P1_7 8051 CPU CORE P1_6 P1_5 MEMORY ARBITER P1_4 128/256 KB FLASH P1_3 P1_2 DMA P1_1 P1_0 FLASH CTRL P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 12-Bit DS ADC AES ENCRYPTION and DECRYPTION RADIO REGISTERS CSMA/CA STROBE PROCESSOR RADIO DATA INTERFACE DEMODULATOR and AGC MODULATOR USART 0 FREQUENCY SYNTHESIZER USART 1 TIMER 1 (16-bit) TIMER 2 (IEEE 802.15.4 MAC TIMER) RECEIVE TIMER 3 (8-bit) FIFO AND FRAME CONTROL P0_6 SYNTH P0_7 I/O CONTROLLER IRQ CTRL TRANSMIT TIMER 4 (8-bit) DIGITAL RF_P RF_N ANALOG MIXED Figure 7. CC2531 Block Diagram A block diagram of the CC2531 is shown in Figure 7. The modules can be roughly divided into one of three categories: CPU- and memory-related modules; modules related to peripherals, clocks, and power management; and radio-related modules. In the following subsections, a short description of each module that appears in Figure 7 is given. 18 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 For more details about the modules and their usage, see the corresponding chapters in the CC253x User's Guide (SWRU191). CPU and Memory The 8051 CPU core used in the CC253x device family is a single-cycle 8051-compatible core. It has three different memory-access buses (SFR, DATA, and CODE/XDATA) with single-cycle access to SFR, DATA, and the main SRAM. It also includes a debug interface and an 18-input extended interrupt unit. The interrupt controller services a total of 18 interrupt sources, divided into six interrupt groups, each of which is associated with one of four interrupt priorities. Any interrupt service request is serviced also when the device is in idle mode by going back to active mode. Some interrupts can also wake up the device from sleep mode (power modes 1–3). The memory arbiter is at the heart of the system, as it connects the CPU and DMA controller with the physical memories and all peripherals through the SFR bus. The memory arbiter has four memory access points, access of which can map to one of three physical memories: an 8-KB SRAM, flash memory, and XREG/SFR registers. It is responsible for performing arbitration and sequencing between simultaneous memory accesses to the same physical memory. The 8-KB SRAM maps to the DATA memory space and to parts of the XDATA memory spaces. The 8-KB SRAM is an ultralow-power SRAM that retains its contents even when the digital part is powered off (power modes 2 and 3). This is an important feature for low-power applications. The 256 KB flash block provides in-circuit programmable non-volatile program memory for the device, and maps into the CODE and XDATA memory spaces. In addition to holding program code and constants, the non-volatile memory allows the application to save data that must be preserved such that it is available after restarting the device. Using this feature one can, e.g., use saved network-specific data to avoid the need for a full start-up and network find-and-join process. Clocks and Power Management The digital core and peripherals are powered by a 1.8-V low-dropout voltage regulator. It provides power management functionality that enables low-power operation for long battery life using different power modes. Five different reset sources exist to reset the device. Peripherals The CC2531 includes many different peripherals that allow the application designer to develop advanced applications. The debug interface implements a proprietary two-wire serial interface that is used for in-circuit debugging. Through this debug interface, it is possible to perform an erasure of the entire flash memory, control which oscillators are enabled, stop and start execution of the user program, execute supplied instructions on the 8051 core, set code breakpoints, and single-step through instructions in the code. Using these techniques, it is possible to perform in-circuit debugging and external flash programming elegantly. The device contains flash memory for storage of program code. The flash memory is programmable from the user software and through the debug interface. The flash controller handles writing and erasing the embedded flash memory. The flash controller allows page-wise erasure and 4-bytewise programming. The I/O controller is responsible for all general-purpose I/O pins. The CPU can configure whether peripheral modules control certain pins or whether they are under software control, and if so, whether each pin is configured as an input or output and if a pullup or pulldown resistor in the pad is connected. CPU interrupts can be enabled on each pin individually. Each peripheral that connects to the I/O pins can choose between two different I/O pin locations to ensure flexibility in various applications. A versatile five-channel DMA controller is available in the system, accesses memory using the XDATA memory space, and thus has access to all physical memories. Each channel (trigger, priority, transfer mode, addressing mode, source and destination pointers, and transfer count) is configured with DMA descriptors anywhere in memory. Many of the hardware peripherals (AES core, flash controller, USARTs, timers, ADC interface) achieve highly efficient operation by using the DMA controller for data transfers between SFR or XREG addresses and flash/SRAM. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 19 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com Timer 1 is a 16-bit timer with timer/counter/PWM functionality. It has a programmable prescaler, a 16-bit period value, and five individually programmable counter/capture channels, each with a 16-bit compare value. Each of the counter/capture channels can be used as a PWM output or to capture the timing of edges on input signals. It can also be configured in IR Generation Mode, where it counts Timer 3 periods and the output is ANDed with the output of Timer 3 to generate modulated consumer IR signals with minimal CPU interaction. Timer 2 (the MAC Timer) is specially designed for supporting an IEEE 802.15.4 MAC or other time-slotted protocol in software. The timer has a configurable timer period and a 24-bit overflow counter that can be used to keep track of the number of periods that have transpired. A 40-bit capture register is also used to record the exact time at which a start-of-frame delimiter is received/transmitted or the exact time at which transmission ends, as well as two 16-bit output compare registers and two 24-bit overflow compare registers that can send various command strobes (start RX, start TX, etc.) at specific times to the radio modules. Timer 3 and Timer 4 are 8-bit timers with timer/counter/PWM functionality. They have a programmable prescaler, an 8-bit period value, and one programmable counter channel with an 8-bit compare value. Each of the counter channels can be used as a PWM output. The sleep timer is an ultralow-power timer that counts 32-kHz crystal oscillator or 32-kHz RC oscillator periods. The sleep timer runs continuously in all operating modes except power mode 3 (PM3). Typical applications of this timer are as a real-time counter or as a wake-up timer to come out of power mode 1 (PM1) or 2 (PM2). The ADC supports 7 to 12 bits of resolution in a 30-kHz to 4-kHz bandwidth, respectively. DC and audio conversions with up to eight input channels (Port 0) are possible. The inputs can be selected as single-ended or differential. The reference voltage can be internal, AVDD, or a single-ended or differential external signal. The ADC also has a temperature-sensor input channel. The ADC can automate the process of periodic sampling or conversion over a sequence of channels. The random-number generator uses a 16-bit LFSR to generate pseudorandom numbers, which can be read by the CPU or used directly by the command strobe processor. It can be seeded with random data from noise in the radio ADC. The AES encryption/decryption core allows the user to encrypt and decrypt data using the AES algorithm with 128-bit keys. The core is able to support the AES operations required by IEEE 802.15.4 MAC security, the ZigBee network layer, and the application layer. A built-in watchdog timer allows the CC2531 to reset itself in case the firmware hangs. When enabled by software, the watchdog timer must be cleared periodically; otherwise, it resets the device when it times out. It can alternatively be configured for use as a general 32-kHz timer. USART 0 and USART 1 are each configurable as either a SPI master/slave or a UART. They provide double buffering on both RX and TX and hardware flow control, and are thus well suited to high-throughput full-duplex applications. Each has its own high-precision baud-rate generator, thus leaving the ordinary timers free for other uses. The USB device operates at full-speed, 12-Mbps transfer rate. The controller has 5 bidirectional endpoints in addition to control endpoint 0. The endpoints support bulk, interrupt, and isochronous operation for implementation of a wide range of applications. The 1024 bytes of dedicated, flexible FIFO memory combined with DMA access ensures that a minimum of CPU involvement is needed for USB communication. Radio The CC2531 features an IEEE 802.15.4-compliant radio transceiver. The RF core controls the analog radio modules. In addition, it provides an interface between the MCU and the radio which makes it possible to issue commands, read status, and automate and sequence radio events. The radio also includes a packet-filtering and address-recognition module. 20 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 TYPICAL CHARACTERISTICS RX CURRENT (–100-dBm INPUT) vs TEMPERATURE TX CURRENT (TXPOWER = 0xF5) vs TEMPERATURE 36 28 27 26 TX Current − mA RX Current − mA 35 25 24 34 33 23 22 −40 0 40 80 32 −40 120 0 40 80 G002 Figure 8. Figure 9. RX CURRENT (–100-dBm INPUT) vs SUPPLY VOLTAGE TX CURRENT (TXPOWER = 0xF5) vs SUPPLY VOLTAGE 26.0 34.4 25.5 34.2 TX Current − mA RX Current − mA G001 25.0 24.5 24.0 2.0 120 T − Temperature − °C T − Temperature − °C 34.0 33.8 2.4 2.8 3.2 VCC − Supply Voltage − V 3.6 33.6 2.0 2.4 G003 Figure 10. 2.8 3.2 VCC − Supply Voltage − V 3.6 G004 Figure 11. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 21 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com TYPICAL CHARACTERISTICS (continued) INTERFERER REJECTION (802.15.4 INTERFERER) vs INTERFERER FREQUENCY (CARRIER AT –82 dBm, 2440 MHz) 75 OUTPUT POWER (TXPOWER = 0xF5) vs FREQUENCY 6.0 50 Interferer Rejection − dB PO − Output Power − dBm 5.5 5.0 4.5 25 0 4.0 3.5 2394 2414 2434 2454 2474 −25 2400 2494 f − Frequency − MHz 2420 2440 2460 2480 Interferer Frequency − MHz G005 G006 Figure 12. Figure 13. SENSITIVITY vs TEMPERATURE OUTPUT POWER (TXPOWER = 0xF5) vs TEMPERATURE −92 8 −93 PO − Output Power − dBm 6 Sensitivity − dBm −94 −95 −96 −97 4 2 0 −98 −99 −40 0 40 80 120 −2 −40 0 T − Temperature − °C 40 G007 Submit Documentation Feedback 120 G008 Figure 14. 22 80 T − Temperature − °C Figure 15. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 TYPICAL CHARACTERISTICS (continued) OUTPUT POWER (TXPOWER = 0xF5) vs SUPPLY VOLTAGE SENSITIVITY vs SUPPLY VOLTAGE 5.0 −94 −95 Sensitivity − dBm PO − Output Power − dBm 4.8 4.6 4.4 −96 −97 −98 4.2 −99 4.0 2.0 2.4 2.8 3.2 VCC − Supply Voltage − V −100 2.0 3.6 2.4 2.8 3.2 VCC − Supply Voltage − V G009 Figure 16. 3.6 G010 Figure 17. Table 1. Recommended Output Power Settings (1) (1) TXPOWER Register Setting Typical Output Power (dBm) Typical Current Consumption (mA) 0xF5 4.5 34 0xE5 2.5 31 0xD5 1 29 0xC5 –0.5 28 0xB5 –1.5 27 0xA5 –3 27 0x95 –4 26 0x85 –6 26 0x75 –8 25 0x65 –10 25 0x55 –12 25 0x45 –14 25 0x35 –16 25 0x25 –18 24 0x15 –20 24 0x05 –22 23 0x05 and TXCTRL = 0x09 –28 23 Measured on Texas Instruments CC2530 EM reference design with TA = 25°C, VDD = 3 V, and fc = 2440 MHz, unless otherwise noted. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 23 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com APPLICATION INFORMATION Few external components are required for the operation of the CC2531. A typical application circuit is shown in Figure 18. For a complete USB-certified reference design, see the CC2531 product page on www.ti.com. Typical values and description of external components are shown in Table 2. The USB_P and USB_N pins need series resistors R21 and R31 for impedance matching, and the D+ line must have a pullup resistor, R32. The series resistors should match the 90 Ω ±15% characteristic impedance of the USB bus. Notice that the pullup resistor and DVDD_USB must be connected to a voltage source between 3 V and 3.6 V (typically 3.3 V). The voltage source should be derived from or controlled by the VBUS power supply provided by the USB cable. In this way, the pullup resistor does not provide current to the D+ line when VBUS is removed. The pullup resistor may be connected directly between VBUS and the D+ line. As an alternative, if the CC2531 firmware needs the ability to disconnect from the USB bus, a GPIO on the CC2531 can be used to control the pullup resistor. Optional 32-kHz Crystal C331 2-V–3.6-V Power Supply XTAL C401 3.3-V Power Supply 2 USB_P C41 D– R21 C31 3 USB_N AVDD6 31 P2_4/XOSC32K_Q1 32 P2_2 34 P2_1 35 P2_0 36 P1_7 37 P1_6 38 1 DGND_USB R31 D+ P2_3/XOSC32K_Q2 33 R32 DVDD1 39 DCOUPL 40 C321 L252 AVDD4 29 AVDD1 28 C251 C252 Antenna (50 W) AVDD2 27 4 DVDD_USB C21 R301 RBIAS 30 C253 RF_N 26 5 P1_5 CC2531 RF_P 25 6 P1_4 DIE ATTACH PAD 7 P1_3 C261 L261 AVDD3 24 XOSC_Q2 23 8 P1_2 C262 18 P0_1 19 P0_0 16 P0_3 17 P0_2 15 P0_4 13 P0_6 14 P0_5 11 P1_0 12 P0_7 10 DVDD2 20 RESET_N XOSC_Q1 22 9 P1_1 AVDD5 21 XTAL C221 C231 S0383-04 Power supply decoupling capacitors are not shown. Digital I / O not connected. Figure 18. CC2531 Application Circuit 24 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 Table 2. Overview of External Components (Excluding Supply Decoupling Capacitors) Component Description Value C21 USB D– decoupling 47 pF C31 USB D+ decoupling 47 pF C41 Decoupling capacitor for USB pad power supply 10 pF C221 32-MHz xtal-loading capacitor 27 pF C231 32-MHz xtal-loading capacitor 27 pF C251 Part of the RF matching network 18 pF C252 Part of the RF matching network 1 pF C253 Part of the RF matching network 2.2 pF C261 Part of the RF matching network 18 pF C262 Part of the RF matching network 1 pF C321 32-kHz xtal-loading capacitor 15 pF C331 32-kHz xtal-loading capacitor 15 pF C401 Decoupling capacitor for the internal digital regulator 1 mF L252 Part of the RF matching network 2 nH L261 Part of the RF matching network 2 nH R21 USB D– series resistor 33 Ω R31 USB D+ series resistor R32 USB D+ pullup resistor to signal full-speed device 1.5 kΩ R301 Resistor used for internal biasing 56 kΩ 33 Ω Input/Output Matching When using an unbalanced antenna such as a monopole, a balun should be used to optimize performance. The balun can be implemented using low-cost discrete inductors and capacitors. The recommended balun shown consists of C262, L261, C252, and L252. If a balanced antenna such as a folded dipole is used, the balun can be omitted. Crystal An external 32-MHz crystal, XTAL1, with two loading capacitors (C221 and C231) is used for the 32-MHz crystal oscillator. See the 32-MHz Crystal Oscillator section for details. The load capacitance seen by the 32-MHz crystal is given by: 1 CL = + Cparasitic 1 1 + C221 C231 (1) XTAL2 is an optional 32.768-kHz crystal, with two loading capacitors (C321 and C331) used for the 32.768-kHz crystal oscillator. The 32.768-kHz crystal oscillator is used in applications where both low sleep-current consumption and accurate wake-up times are needed. The load capacitance seen by the 32.768-kHz crystal is given by: 1 CL = + Cparasitic 1 1 + C321 C331 (2) A series resistor may be used to comply with the ESR requirement. On-Chip 1.8-V Voltage-Regulator Decoupling The 1.8-V on-chip voltage regulator supplies the 1.8-V digital logic. This regulator requires a decoupling capacitor (C401) for stable operation. Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 25 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com Power-Supply Decoupling and Filtering Proper power-supply decoupling must be used for optimum performance. The placement and size of the decoupling capacitors and the power supply filtering are important to achieve the best performance in an application. TI provides a recommended compact reference design for the user to follow. References 1. IEEE Std. 802.15.4-2006: Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) http://standards.ieee.org/getieee802/download/802.15.4-2006.pdf 2. CC253x User's Guide – CC253x System-on-Chip Solution for 2.4 GHz IEEE 802.15.4 and ZigBee Applications (SWRU191) 3. Universal Serial Bus Revision 2.0 Specification http://www.usb.org/developers/docs/usb_20_052709.zip Additional Information Texas Instruments offers a wide selection of cost-effective, low-power RF solutions for proprietary and standard-based wireless applications for use in industrial and consumer applications. The selection includes RF transceivers, RF transmitters, RF front ends, and System-on-Chips as well as various software solutions for the sub-1-GHz and 2.4-GHz frequency bands. In addition, Texas Instruments provides a large selection of support collateral such as development tools, technical documentation, reference designs, application expertise, customer support, third-party and university programs. The Low-Power RF E2E Online Community provides technical support forums, videos and blogs, and the chance to interact with engineers from all over the world. With a broad selection of product solutions, end application possibilities, and a range of technical support, Texas Instruments offers the broadest low-power RF portfolio. Texas Instruments Low-Power RF Web Site Texas Instruments’ Low-Power RF Web site has all the latest products, application and design notes, FAQ section, news and events updates. Go to www.ti.com/lprf. Low-Power RF Online Community • • • Forums, videos, and blogs RF design help E2E interaction Join at: www.ti.com/lprf-forum. 26 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 CC2531F128, CC2531F256 www.ti.com SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 Texas Instruments Low-Power RF Developer Network Texas Instruments has launched an extensive network of low-power RF development partners to help customers speed up their application development. The network consists of recommended companies, RF consultants, and independent design houses that provide a series of hardware module products and design services, including: • RF circuit, low-power RF, and ZigBee design services • Low-power RF and ZigBee module solutions and development tools • RF certification services and RF circuit manufacturing For help with modules, engineering services or development tools: Search the Low-Power RF Developer Network to find a suitable partner. www.ti.com/lprfnetwork Low-Power RF eNewsletter The Low-Power RF eNewsletter is up-to-date on new products, news releases, developers’ news, and other news and events associated with low-power RF products from TI. The Low-Power RF eNewsletter articles include links to get more online information. Sign up at: www.ti.com/lprfnewsletter Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 Submit Documentation Feedback 27 CC2531F128, CC2531F256 SWRS086A – SEPTEMBER 2009 – REVISED JUNE 2010 www.ti.com REVISION HISTORY Changes from Revision Original (September 2009) to Revision A Page • Changed recommendation for single-crystal implementations to asynchronous networks. ................................................. 1 • Added F128 version of CC2531 to data sheet. .................................................................................................................... 1 • Added number of erase cycles and page size for flash. ....................................................................................................... 4 • Added number of erase cycles and page size for flash. ....................................................................................................... 5 • Updated ESR for 32 kHz crystal. .......................................................................................................................................... 8 • Updated voltage coefficient for temperature sensor. ............................................................................................................ 9 • Changed SPI AC characteristics SSN low from SCK negative edge to SCK positive edge and split it into separate master and slave figures. .................................................................................................................................................... 12 • Corrected description of Timer 2 (MAC Timer). .................................................................................................................. 20 • Improved readability of sleep timer description. ................................................................................................................. 20 • Removed sentence that pseudorandom data can be used for security. ............................................................................ 20 28 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated Product Folder Link(s): CC2531F128 CC2531F256 PACKAGE OPTION ADDENDUM www.ti.com 5-Jul-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) CC2531F128RHAR ACTIVE VQFN RHA 40 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples CC2531F128RHAT ACTIVE VQFN RHA 40 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples CC2531F256RHAR ACTIVE VQFN RHA 40 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples CC2531F256RHAT ACTIVE VQFN RHA 40 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2011 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant CC2531F128RHAR VQFN RHA 40 2500 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 CC2531F128RHAT VQFN RHA 40 250 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 CC2531F256RHAT VQFN RHA 40 250 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2011 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CC2531F128RHAR VQFN RHA 40 2500 333.2 345.9 28.6 CC2531F128RHAT VQFN RHA 40 250 333.2 345.9 28.6 CC2531F256RHAT VQFN RHA 40 250 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee® Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated