TI TPA2039D1YFFR

TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
3.2W Mono Class-D Audio Power Amplifier
With 12-dB Gain and Auto Short-Circuit Recovery
Check for Samples: TPA2039D1
FEATURES
APPLICATIONS
•
•
•
•
1
•
•
•
•
•
•
•
•
•
Powerful Mono Class-D Speaker Amplifier
– 3.24 W (4 Ω, 5 V, 10% THDN)
– 2.57 W (4 Ω, 5 V, 1% THDN)
– 1.80 W (8 Ω, 5 V, 10% THDN)
– 1.46 W (8 Ω, 5 V, 1% THDN)
+12 dB Fixed Gain
Integrated Image Reject Filter for DAC Noise
Reduction
Low Output Noise of 27 μV
Low Quiescent Current of 1.5 mA
Differential Input Impedance of 150 kΩ
Auto-Recovering Short-Circuit Protection
Thermal-Overload Protection
Filter-Free Mono Class-D Amp
9-Ball 1,21 mm × 1,16 mm 0,4mm Pitch WCSP
Wireless or Cellular Handsets and PDAs
Portable Navigation Devices
General Portable Audio Devices
DESCRIPTION
The TPA2039D1 is a 3.2 W high efficiency filter-free
class-D audio power amplifier (class-D amp) with
12 dB of fixed gain in a tiny 1.21 mm x 1.16 mm
wafer chip scale package (WCSP). The device
requires only one external component.
Features like 93% efficiency, 1.5 mA quiescent
current, 0.1 μA shutdown current, 82-dB PSRR,
27 μV output noise and improved RF immunity make
the TPA2039D1 class-D amplifier ideal for cellular
handsets. A fast start-up time of 4 ms with no audible
pop makes the TPA2039D1 ideal for PDA and
smart-phone applications.
APPLICATION CIRCUIT
VDD
IN+
VO+
–
PWM
To battery
Cs
Internal
Oscillator
H-Bridge
VO+
TPA2039D1
9-BALL 0.4mm PITCH
WAFER CHIP SCALE PACKAGE (YFF)
(TOP VIEW OF PCB)
IN+
GND
VO-
A1
A2
A3
VDD
PVDD
PGND
B1
B2
B3
IN-
EN
VO+
C1
C2
C3
EN
Bias
Circuitry
GND
1.160 mm
IN-
TPA 2039 D1
1.214 mm
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION
PACKAGED DEVICES (1)
TA
—40°C to 85°C
(1)
(2)
PART NUMBER (2)
SYMBOL
TPA2039D1YFFR
DAR
TPA2039D1YFFT
DAR
9-ball WSCP
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com
The YFF package is only available taped and reeled. The suffix "R" indicates a reel of 3000, the suffix "T" indicates a reel of 250.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range, TA = 25°C (unless otherwise noted) (1)
In active mode
VDD, PVDD
Supply voltage
VI
Input voltage
RL
Minimum load resistance
In shutdown mode
EN, IN+, IN–
Output continuous total power dissipation
VALUE
UNIT
–0.3 to 6.0
V
–0.3 to 6.0
V
–0.3 to VDD + 0.3
V
3.2
Ω
See Dissipation Rating Table
TA
Operating free-air temperature range
–40 to 85
°C
TJ
Operating junction temperature range
–40 to 150
°C
Tstg
Storage temperature range
–65 to 85
°C
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods may affect device reliability.
DISSIPATION RATINGS
(1)
PACKAGE
DERATING FACTOR (1)
TA < 25°C
TA = 70°C
TA = 85°C
YFF (WCSP)
4.2 mW/°C
525 mW
336 mW
273 mW
Derating factor measure with high K board.
RECOMMENDED OPERATING CONDITIONS
VDD,
PVDD
Class-D supply voltage
VIH
High-level input voltage
EN
VIL
Low-level input voltage
EN
VIC
Common mode input voltage range
VDD = 2.5V, 5.5V, CMRR ≥ 49 dB
TA
Operating free-air temperature
2
MIN
MAX
2.5
5.5
1.3
V
V
0.35
Submit Documentation Feedback
UNIT
V
0.75
VDD-1.1
V
–40
85
°C
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
ELECTRICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
|VOS|
Output offset voltage (measured
differentially)
VI = 0 V, VDD = 2.5 V to 5.5 V
|IIH|
High-level EN input current
VDD = 5.5 V, VEN = 5.5 V
|IIL|
Low-level EN input current
VDD = 5.5 V, VEN = 0 V
MIN
TYP
MAX
1
10
mV
50
μA
1
μA
VDD = 5.5 V, no load
1.8
2.5
VDD = 3.6 V, no load
1.5
2.3
I(Q)
Quiescent current
VDD = 2.5 V, no load
1.3
2.1
I(SD)
Shutdown current
VEN = 0.35 V, VDD = 3.6 V
0.1
2
RO,
Output impedance in shutdown mode
VEN = 0.35 V
f(SW)
Switching frequency
VDD = 2.5 V to 5.5 V
250
AV
Gain
VDD = 2.5 V to 5.5 V, RL = no load
11.5
REN
Resistance from EN to GND
RIN
Single ended input resistance
SD
UNIT
mA
μA
2
kΩ
300
350
12
12.5
kHz
dB
300
VEN ≥ VIH
75
VEN ≤ VIL
75
kΩ
kΩ
OPERATING CHARACTERISTICS
VDD = 3.6 V, TA = 25°C, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
THD + N = 10%, f = 1 kHz, RL = 4 Ω
THD + N = 1%, f = 1 kHz, RL = 4 Ω
PO
Output power
THD + N = 10%, f = 1 kHz, RL = 8 Ω
THD + N = 1%, f = 1 kHz, RL = 8 Ω
Vn
THD+N
Noise output voltage
Total harmonic distortion plus
noise
VDD = 3.6 V, Inputs AC grounded
with CI = 2μF, f = 20 Hz to 20 kHz
MIN
TYP
VDD = 5 V
3.24
VDD = 3.6 V
1.62
VDD = 2.5 V
0.70
VDD = 5 V
2.57
VDD = 3.6 V
1.32
VDD = 2.5 V
0.57
VDD = 5 V
1.80
VDD = 3.6 V
0.91
VDD = 2.5 V
0.42
VDD = 5 V
1.46
VDD = 3.6 V
0.74
VDD = 2.5 V
0.33
A-weighting
27
No weighting
36
VDD = 5.0 V, PO = 1.0 W, f = 1 kHz, RL = 8 Ω
0.12%
VDD = 3.6 V, PO = 0.5 W, f = 1 kHz, RL = 8 Ω
0.05%
VDD = 2.5 V, PO = 0.2 W, f = 1 kHz, RL = 8 Ω
0.05%
VDD = 5.0 V, PO = 2.0 W, f = 1 kHz, RL = 4 Ω
0.32%
VDD = 3.6 V, PO = 1.0 W, f = 1 kHz, RL = 4 Ω
0.11%
VDD = 2.5 V, PO = 0.4 W, f = 1 kHz, RL = 4 Ω
0.12%
MAX
UNIT
W
W
W
W
μVRMS
PSRR
AC power supply rejection ratio
VDD = 3.6 V, Inputs AC grounded with CI = 2 μF,
200 mVpp ripple, f = 217 Hz
82
dB
CMRR
Common mode rejection ratio
VDD = 3.6 V, VIC = 1 VPP, f = 217 Hz
77
dB
TSU
Startup time from shutdown
VDD = 3.6 V
4
ms
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
3
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
OPERATING CHARACTERISTICS (continued)
VDD = 3.6 V, TA = 25°C, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Short circuit protection
threshold
ISC
Time for which output is
disabled after a short circuit
event, after which
auto-recovery trials are
continuously made
TAR
MIN
TYP
VDD = 3.6 V, VO+ shorted to VDD
2
VDD = 3.6 V, VO– shorted to VDD
2
VDD = 3.6 V, VO+ shorted to GND
2
VDD = 3.6 V, VO– shorted to GND
2
VDD = 3.6 V, VO+ shorted to VO–
2
VDD = 2.5 V to 5.5 V
100
MAX
UNIT
A
ms
Terminal Functions
TERMINAL
NAME
WCSP BALL
I/O
DESCRIPTION
IN–
C1
I
Negative differential audio input.
IN+
A1
I
Positive differential audio input.
VO-
A3
O
Negative BTL audio output.
VO+
C3
O
Positive BTL audio output.
GND
A2
I
Analog ground terminal. Must be connected to same potential as PGND using a direct connection
to a single point ground.
PGND
B3
I
High-current Analog ground terminal. Must be connected to same potential as GND using a direct
connection to a single point ground.
VDD
B1
I
Power supply terminal. Must be connected to same power supply as PVDD using a direct
connection. Voltage must be within values listed in Recommended Operating Conditions table.
PVDD
B2
I
High-current Power supply terminal. Must be connected to same power supply as VDD using a
direct connection. Voltage must be within values listed in Recommended Operating Conditions
table.
EN
C2
I
Enable terminal. Connect to Logic High voltage to enable device, Logic Low voltage to disable
(shutdown).
FUNCTIONAL BLOCK DIAGRAM
EN
Input
Buffer
SC
300 KΩ
4
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
TEST SETUP FOR GRAPHS
CI
+
Measurement
Output
OUT+
IN+
TPA2039D1
CI
-
IN-
+
Load
30 kHz
Low Pass
Filter
OUTVDD
Measurement
Input
-
GND
CS1
CS2
+
VDD
-
1. CI was shorted for any common-mode input voltage measurement. All other measurements were taken with CI = 0.1-μF
(unless otherwise noted).
2. CS1 = 0.1μF is placed very close to the device. The optional CS2 = 10μF is used for datasheet graphs.
3. The 30-kHz low-pass filter is required even if the analyzer has an internal low-pass filter. An RC low-pass filter (1kΩ,
4700pF) is used on each output for the data sheet graphs.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
5
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS
VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
EFFICIENCY
vs OUTPUT POWER
100
100
90
90
80
80
70
70
60
50
40
RL = 8 Ω + 33 µH
30
20
0.4
0.6
0.8
1.0
1.2
1.4
1.8
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
0.4
0.8
1.2
1.6
2.0
2.4
PO − Output Power − W
Figure 1.
Figure 2.
POWER DISSIPATION
vs OUTPUT POWER
POWER DISSIPATION
vs OUTPUT POWER
0.5
0.2
0.1
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0.2
0.1
0.4
0.8
1.2
1.6
2.0
2.4
Figure 3.
Figure 4.
SUPPLY CURRENT
vs OUTPUT POWER
SUPPLY CURRENT
vs OUTPUT POWER
IDD − Supply Current − A
600m
500m
400m
300m
200m
3.2
3.6
4.0
RL = 8 Ω + 33 µH
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
400m
700m
2.8
500m
RL = 4 Ω + 33 µH
4.0
0.3
PO − Output Power − W
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
3.6
VDD = 5.0 V
PO − Output Power − W
900m
3.2
0.4
0.0
0.0
2.0
2.8
RL = 8 Ω + 33 µH
RL = 4 Ω + 33 µH
VDD = 3.6 V
0.3
800m
RL = 4 Ω + 33 µH
30
PO − Output Power − W
RL = 8 Ω + 33 µH
RL = 4 Ω + 33 µH
0.2
40
0
0.0
2.0
0.4
0.0
0.0
IDD − Supply Current − A
1.6
50
10
PD − Power Dissipation − W
PD − Power Dissipation − W
0.5
0.2
60
20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
10
0
0.0
η − Efficiency − %
η − Efficiency − %
EFFICIENCY
vs OUTPUT POWER
300m
200m
100m
100m
0
0.0
6
0.4
0.8
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
PO − Output Power − W
PO − Output Power − W
Figure 5.
Figure 6.
Submit Documentation Feedback
1.4
1.6
1.8
2.0
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
TYPICAL CHARACTERISTICS (continued)
VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
SUPPLY CURRENT
vs SUPPLY VOLTAGE
SUPPLY CURRENT
vs EN VOLTAGE
2.00
200
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
1.75
IDD − Supply Current − nA
IDD − Supply Current − mA
RL = No Load
RL = 8 Ω + 33 µH
RL = 4 Ω + 33 µH
1.50
1.25
1.00
2.5
3.0
3.5
4.0
4.5
5.0
150
100
50
0
0.0
5.5
0.1
0.2
VDD − Supply Voltage − V
Figure 7.
Figure 8.
OUTPUT POWER
vs LOAD RESISTANCE
OUTPUT POWER
vs LOAD RESISTANCE
4
0.5
3
2
1
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
THD+N = 1 %
Frequency = 1 kHz
PO − Output Power − W
PO − Output Power − W
0.4
4
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
THD+N = 10 %
Frequency = 1 kHz
0
3
2
1
0
4
8
12
16
20
24
28
32
4
8
12
RL − Load Resistance − Ω
3
20
Figure 9.
Figure 10.
OUTPUT POWER
vs SUPPLY VOLTAGE
THD + NOISE
vs OUTPUT POWER
RL = 4 Ω, THD+N = 1 %
RL = 4 Ω, THD+N = 10 %
RL = 8 Ω, THD+N = 1 %
RL = 8 Ω, THD+N = 10 %
2
1
Frequency = 1 kHz
0
2.5
16
3.0
3.5
4.0
24
28
32
RL − Load Resistance − Ω
4.5
5.0
THD+N − Total Harmonic Distortion + Noise − %
4
PO − Output Power − W
0.3
VEN − EN Voltage − V
100
RL = 4 Ω + 33 µH
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
10
1
0.1
0.01
10m
VDD − Supply Voltage − V
100m
1
5
PO − Output Power − W
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
7
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
100
THD + NOISE
vs FREQUENCY
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs OUTPUT POWER
RL = 8 Ω + 33 µH
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
10
1
0.1
0.01
10m
100m
1
10
1
0.1
0.01
0.001
3
20
100
1k
f − Frequency − Hz
THD+N − Total Harmonic Distortion + Noise − %
Figure 14.
THD + NOISE
vs FREQUENCY
THD + NOISE
vs FREQUENCY
10
PO = 25 mW
PO = 125 mW
PO = 500 mW
VDD = 3.6 V
RL = 8 Ω + 33 µH
1
0.1
0.01
0.001
100
1k
f − Frequency − Hz
10k
0.1
0.01
0.001
20
100
THD + NOISE
vs FREQUENCY
0.1
0.01
0.001
1k
f − Frequency − Hz
10k
20k
10k
20k
10
PO = 50 mW
PO = 250 mW
PO = 1 W
VDD = 3.6 V
RL = 4 Ω + 33 µH
1
0.1
0.01
0.001
20
Figure 17.
8
1k
f − Frequency − Hz
THD + NOISE
vs FREQUENCY
1
100
1
Figure 16.
PO = 100 mW
PO = 500 mW
PO = 2 W
20k
PO = 15 mW
PO = 75 mW
PO = 200 mW
VDD = 2.5 V
RL = 8 Ω + 33 µH
Figure 15.
VDD = 5.0 V
RL = 4 Ω + 33 µH
10k
10
20k
10
20
THD+N − Total Harmonic Distortion + Noise − %
Figure 13.
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
PO − Output Power − W
20
PO = 50 mW
PO = 250 mW
PO = 1 W
VDD = 5.0 V
RL = 8 Ω + 33 µH
100
1k
f − Frequency − Hz
10k
20k
Figure 18.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
TYPICAL CHARACTERISTICS (continued)
VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
THD + NOISE vs
COMMON MODE INPUT VOLTAGE
10
PO = 30 mW
PO = 150 mW
PO = 400 mW
VDD = 2.5 V
RL = 4 Ω + 33 µH
1
0.1
0.01
0.001
20
100
1k
f − Frequency − Hz
10k
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs FREQUENCY
20k
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
1
0.1
0.01
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Figure 19.
Figure 20.
POWER SUPPLY REJECTION RATIO
vs FREQUENCY
POWER SUPPLY REJECTION RATIO
vs FREQUENCY
4.5
5.0
0
Inputs AC−Grounded
CI = 2 µF
RL = 8 Ω + 33 µH
−10
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
PSRR − Power Supply Rejection Ratio − dB
PSRR − Power Supply Rejection Ratio − dB
RL = 8 Ω + 33 µH
Frequency = 1 kHz
PO = 200 mW
VIC − Common Mode Input Voltage − V
0
−100
Inputs AC−Grounded
CI = 2 µF
RL = 4 Ω + 33 µH
−10
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
20
−10
100
1k
f − Frequency − Hz
10k
20k
100
1k
f − Frequency − Hz
10k
Figure 21.
Figure 22.
POWER SUPPLY REJECTION RATIO
vs COMMON MODE INPUT VOLTAGE
COMMON MODE REJECTION RATIO
vs FREQUENCY
RL = 8 Ω + 33 µH
Frequency = 217 Hz
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−20
−30
−40
−50
−60
−70
−80
−90
−100
0.0
20
CMRR − Common Mode Rejection Ratio − dB
0
PSRR − Power Supply Rejection Ratio − dB
10
20k
−30
VIC = 1 VPP
RL = 8 Ω + 33 µH
−40
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−50
−60
−70
−80
−90
−100
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
20
VIC − Common Mode Input Voltage − V
Figure 23.
100
1k
f − Frequency − Hz
10k
20k
Figure 24.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
9
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
COMMON MODE REJECTION RATIO
vs COMMON MODE INPUT VOLTAGE
CMRR − Common Mode Rejection Ratio − dB
0
RL = 8 Ω + 33 µH
Frequency = 217 Hz
−10
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−20
−30
−40
−50
−60
−70
−80
−90
−100
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VIC − Common Mode Input Voltage − V
Figure 25.
GSM POWER SUPPLY REJECTION
vs TIME
C1 - High
3.6 V
VDD
500 mV/div
C1 - Amplitude
500 mV
C1 - Duty Cycle
20%
VOUT
100 mV/div
0
2.5
5
7.5
10
12.5
15
17.5
20
22.5
25
t − Time − ms
Figure 26.
0
−25
−50
−75
−100
VO − Output Voltage − dBV
−125
−25
−150
−50
−175
VDD − Supply Voltage − dBV
GSM POWER SUPPLY REJECTION
vs FREQUENCY
−75
−100
−125
−150
−175
−200
0
2.4
4.8
7.2
9.6
12
14.4
16.8
19.2
21.6
24
f − Frequency − kHz
Figure 27.
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
APPLICATION INFORMATION
SHORT CIRCUIT AUTO-RECOVERY
When a short-circuit event occurs, the TPA2039D1 goes to shutdown mode and activates the integrated
auto-recovery process whose aim is to return the device to normal operation once the short-circuit is removed.
This process repeatedly examines (once every 100ms) whether the short-circuit condition persists, and returns
the device to normal operation immediately after the short-circuit condition is removed. This feature helps protect
the device from large currents and maintain a good long-term reliability.
INTEGRATED IMAGE REJECT FILTER FOR DAC NOISE REJECTION
In applications which use a DAC to drive Class-D amplifiers, out-of-band noise energy present at the DAC's
image frequencies fold back into the audio-band at the output of the Class-D amplifier. An external low-pass filter
is often placed between the DAC and the Class-D amplifier in order to attenuate this noise.
The TPA2039D1 has an integrated Image Reject Filter with a low-pass cutoff frequency of 130 kHz, which
significantly attenuates this noise. Depending on the system noise specification, the integrated Image Reject
Filter may help eliminate external filtering, thereby saving board space and component cost.
COMPONENT SELECTION
Figure 28 shows the TPA2039D1 typical schematic with differential inputs, while Figure 29 shows the
TPA2039D1 with differential inputs and input capacitors. Figure 30 shows the TPA2039D1 with a single-ended
input.
Decoupling Capacitors (CS1, CS2)
The TPA2039D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor CS1 = 0.1μF ,
placed as close as possible to the device VDD lead works best. Placing CS1 close to the TPA2039D1 is important
for the efficiency of the class-D amplifier, because any resistance or inductance in the trace between the device
and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise signals, a 10 μF or greater
capacitor (CS2) placed near the audio power amplifier would also help, but it is not required in most applications
because of the high PSRR of this device. Typically, the smaller the capacitor's case size, the lower the
inductance and the closer it can be placed to the TPA2039D1. X5R and X7R dielectric capacitors are
recommended for both CS1 and CS2.
Input Capacitors (CI)
The TPA2039D1 does not require input coupling capacitors if the design uses a differential source that is biased
within the common-mode input voltage range. That voltage range is listed in the Recommended Operating
Conditions table. If the input signal is not biased within the recommended common-mode input range, such as in
needing to use the input as a high pass filter, shown in Figure 29, or if using a single-ended source, shown in
Figure 30, input coupling capacitors are required. The same value capacitors should be used on both IN+ and
IN– for best pop performance. The 3-dB high-pass cutoff frequency fC of the filter formed by the input coupling
capacitor CI and the input resistance RI (typically 75 kΩ) of the TPA2039D1 is given by Equation 1:
1
fC =
(2πRICI )
(1)
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speaker response may also be taken into consideration when setting the corner
frequency using input capacitors. Solving for the input coupling capacitance, we get:
1
CI =
2πR
( IfC )
(2)
If the corner frequency is within the audio band, the capacitors should have a tolerance of ±10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
11
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
For a flat low-frequency response, use large input coupling capacitors (0.1 μF or larger). X5R and X7R dielectric
capacitors are recommended.
To Battery
Internal
Oscillator
VDD
CS
IN−
PWM
_
Differential
Input
H−
Bridge
VO−
VO+
+
IN+
GND
Bias
Circuitry
EN
TPA2039D1
Filter-Free Class D
Figure 28. Typical TPA2039D1 Application Schematic With DC-coupled Differential Input
To Battery
CI
Internal
Oscillator
CS
IN−
PWM
_
Differential
Input
VDD
CI
H−
Bridge
VO−
VO+
+
IN+
GND
EN
Bias
Circuitry
TPA2039D1
Filter-Free Class D
Figure 29. TPA2039D1 Application Schematic With Differential Input and Input Capacitors
CI
Single-ended
Input
To Battery
Internal
Oscillator
VDD
IN−
_
PWM
H−
Bridge
CS
VO−
VO+
+
IN+
CI
GND
EN
Bias
Circuitry
TPA2039D1
Filter-Free Class D
Figure 30. TPA2039D1 Application Schematic With Single-Ended Input
12
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
EFFICIENCY AND THERMAL INFORMATION
The maximum ambient operating temperature of the TPA2039D1 depends on the load resistance, power supply
voltage and heat-sinking ability of the PCB system. The derating factor for the YFF package is shown in the
dissipation rating table. Converting this to θJA:
1
q
+
JA
Derating Factor
(3)
Given θJA (from the Package Dissipation ratings table), the maximum allowable junction temperature (from the
Absolute Maximum ratings table), and the maximum internal dissipation (from Power Dissipation vs Output
Power figures) the maximum ambient temperature can be calculated with the following equation. Note that the
units on these figures are Watts RMS. Because of crest factor (ratio of peak power to RMS power) from 9–15
dB, thermal limitations are not usually encountered.
T Max + T Max * q P
A
J
JA Dmax
(4)
The TPA2039D1 is designed with thermal protection that turns the device off when the junction temperature
surpasses 150°C to prevent damage to the IC. Note that the use of speakers less resistive than 4-Ω (typ) is not
advisable. Below 4-Ω (typ) the thermal performance of the device dramatically reduces because of increased
output current and reduced amplifier efficiency. The Absolute Maximum rating of 3.2-Ω covers the manufacturing
tolerance of a 4-Ω speaker and speaker impedance decrease due to frequency. θJA is a gross approximation of
the complex thermal transfer mechanisms between the device and its ambient environment. If the θJA calculation
reveals a potential problem, a more accurate estimate should be made.
WHEN TO USE AN OUTPUT FILTER
Design the TPA2039D1 without an Inductor / Capacitor (LC) output filter if the traces from the amplifier to the
speaker are short. Wireless handsets and PDAs are great applications for this class-D amplifier to be used
without an output filter.
The TPA2039D1 does not require an LC output filter for short speaker connections (approximately 100 mm long
or less). A ferrite bead can often be used in the design if failing radiated emissions testing without an LC filter;
and, the frequency-sensitive circuit is greater than 1 MHz. If choosing a ferrite bead, choose one with high
impedance at high frequencies, but very low impedance at low frequencies. The selection must also take into
account the currents flowing through the ferrite bead. Ferrites can begin to loose effectiveness at much lower
than rated current values. See the TPA2039D1 EVM User's Guide for components used successfully by TI.
Figure 31 shows a typical ferrite-bead output filter.
Ferrite
Chip Bead
VO−
1 nF
Ferrite
Chip Bead
VO+
1 nF
Figure 31. Typical Ferrite Chip Bead Filter
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
13
TPA2039D1
SLOS652 – DECEMBER 2009
www.ti.com
PRINTED CIRCUIT BOARD LAYOUT
In making the pad size for the WCSP balls, it is recommended that the layout use nonsolder mask defined
(NSMD) land. With this method, the solder mask opening is made larger than the desired land area, and the
opening size is defined by the copper pad width. Figure 32 shows the appropriate diameters for a WCSP layout.
Figure 32. Land Pattern Image and Dimensions
SOLDER PAD
DEFINITIONS
COPPER PAD
SOLDER MASK
OPENING(5)
COPPER
THICKNESS
STENCIL OPENING(6) (7)
STENCIL
THICKNESS
Nonsolder mask
defined (NSMD)
0.23 mm
0.310 mm
1 oz max
(0.032 mm)
0.275 mm x 0.275 mm Sq.
(rounded corners)
0.1 mm thick
1. Circuit traces from NSMD defined PWB lands should be 75 μm to 100 μm wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
2. Best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating the range of the intended application.
3. Recommend solder paste is Type 3 or Type 4.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in
thermal fatigue performance.
5. Solder mask thickness should be less than 20 μm on top of the copper circuit pattern
6. Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically
etched stencils give inferior solder paste volume control.
7. Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional
component movement due to solder wetting forces.
Figure 33. Layout Snapshot
An on-pad via is not required to route the middle ball B2 (PVDD) of the TPA2039D1. Just short ball B2 (PVDD) to
ball B1 (VDD) and connect both to the supply trace as shown in Figure 33. This simplifies board routing and
saves manufacturing cost.
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
TPA2039D1
www.ti.com
SLOS652 – DECEMBER 2009
Package Dimensions
D
E
Max = 1244µm
Max = 1190µm
Min = 1184µm
Min = 1130µm
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s) :TPA2039D1
15
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated