TI TX810

TX810
www.ti.com
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
8-Channel, Programmable T/R Switch for Ultrasound
Check for Samples: TX810
FEATURES
DESCRIPTION
•
•
The TX810 provides an integrated solution for a wide
range of ultrasound applications. It is an 8 channel,
current programmable, transmit/receive switch in a
small 6mm × 6mm package.
1
2
•
•
•
Compact T/R Switch for Ultrasound
Flexible Programmability
– 8 Bias Current Settings
– 8 Power/Performance Combinations
– Easy Power-Up/Down control
Fast Wake Up Time
Dual Supply Operation
Optimized Insertion Loss
The internal diodes limit the output voltage when high
voltage transmitter signals are applied to the input.
While the insertion loss of TX810 is minimized during
receive mode.
Unlike conventional T/R switches, the TX810 contains
a 3-bit interface used to program bias current from
7mA to 0mA for different performance and power
requirements. When the TX810 bias current is set as
0mA (i.e., high-impedance mode), the device is
configured
as
power-down
mode.
In
the
high-impedance mode, TX810 does not add
additional load to high-voltage transmitters. In
addition, the device can wake up from power-down
mode in less than 1µs. With these advanced
programmability features, significant power saving
can be achieved in systems.
APPLICATIONS
•
•
Medical Ultrasound
Industrial Ultrasound
VP
1 Channel
of TX810
HV TX
LV RX
VN
Figure 1. Block Diagram of TX810
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009–2010, Texas Instruments Incorporated
TX810
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION (1)
PACKAGED DEVICES
TX810IRHHT
OPERATING TEMPERATURE
RANGE
Tape and Reel, 250
S-PVQFN-N36
TX810IRHHR
(1)
TRANSPORT MEDIA,
QUANTITY
PACKAGE TYPE
0~70°C
Tape and Reel, 2500
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VALUE
UNIT
Supply Voltage, VD
-0.3 ~ +6
V
Supply Voltage, VP
-0.3 ~ +6
V
Supply Voltage, VN
-6 ~ +0.3
V
Supply Voltage, VB
-0.3 ~ +6
V
±100
V
Input AC voltage, INn
Input at Vsub
Output current, IO
Maximum junction temperature, continuous operation, long term reliability (2) TJ
Storage temperature range, Tstg
ESD ratings
(1)
(2)
-6 ~ +0.3
V
15
mA
125°C
-55°C to 150°C
HBM
500
V
CDM
750
V
MM
200
V
Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied Exposure to absolute maximum rated conditions for extended periods may degrade device reliability.
The absolute maximum junction temperature for continuous operation is limited by the package constraints. Operation above this
temperature may result in reduced reliability and/or lifetime of the device.
THERMAL INFORMATION
THERMAL METRIC (1)
(OLFM Airflow Assumed)
TX810
RHH
UNITS
36 PINS
qJA
Junction-to-ambient thermal resistance (2)
qJC(top)
Junction-to-case(top) thermal resistance
qJB
Junction-to-board thermal resistance
yJT
Junction-to-top characterization parameter
yJB
Junction-to-board characterization parameter
(1)
(2)
(3)
(4)
(5)
(6)
2
29.7
(3)
27
(4)
7.2
(5)
°C/W
0.1
(6)
7.2
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, High-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-case(top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDEC-standard
test exists, but a close description can be found in the ANSI SEMI standard G30-88.
The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
The junction-to-top characterization parameter, yJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining qJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, yJB estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining qJA , using a procedure described in JESD51-2a (sections 6 and 7).
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
TX810
www.ti.com
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
DEVICE INFORMATION
PIN FUNCTIONS
PIN
DESCRIPTION
NUMBER
NAME
1, 3, 7, 9, 10, 12, 34,
36
INn
16, 18, 19, 21, 25, 27,
28, 30
OUTn
33
VD
Logic Supply Voltage; +2.5 V to +5 V; bypass to ground with 0.1 µF and 10 µF capacitors
31
VP
Positive Supply Voltage; +5 V; bypass to ground with 0.1 µF and 10 µF capacitors
15
VN
Negative Supply Voltage; –5 V; bypass to ground with 0.1 µF and 10 µF capacitors
13
VB
Bias voltage; connect to 0 V (GND) for ±5 V operation
2, 8, 11, 14, 17, 20, 26,
29, 32, 35
GND
24
B1
Bit 1; Current program bit
23
B2
Bit 2; Current program bit
22
B3
Bit 3; Current program bit
4, 5, 6
NC
No internal connection.
0
Vsub
Inputs for Channel n
Outputs for Channel n
Ground
PowerPAD™ of the package. –5 V to 0 V for ±5 V operation. The thermal pad is needed for thermal
dissipation.
IN7
GND
IN8
VD
GND
VP
OUT8
GND
OUT7
PQFN (RHH) Package
6 × 6mm, 0.5mm Pitch
(Top View)
36
35
34
33
32
31
30
29
28
IN6
1
27
OUT6
GND
2
26
GND
IN5
3
25
OUT5
NC
4
24
B1
NC
5
23
B2
NC
6
22
B3
IN4
7
21
OUT4
GND 8
20
GND
19
OUT3
TX810
PowerPAD™
10
11
12
13
14
15
16
17
18
IN2
GND
IN1
VB
GND
VN
OUT1
GND
OUT2
IN3 9
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
3
TX810
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
www.ti.com
ELECTRICAL CHARACTERISTICS
All Specifications at TA = 25°C, VP = 5V, VN = -5V, VB = 0V, Vsub= -5V, RLOAD = 400Ω; f = 5MHz, B3B2B1 = 111, VIN =
0.25VPP, unless otherwise noted. Test Level: A: Final tester limits; B: bench evaluation/simulation; C: Simulation
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Test
Level
V
B
50
µA
A
0
V
B
V
B
DC POWER SPECIFICATIONS
Positive Supply VP
5
Negative Supply VN
-5
Quiescent current, VP, VN
No Signal
Substrate Voltage, VSUB
PowerPAD™
Digital Supply, VD
VN
2.5
5
Quiescent current, VD
No Signal
µA
A
Bias current, VP, VN path
B3B2B1 = 001
1.25
1
0.75
50
mA/CH
A
Bias current, VP, VN path
B3B2B1 = 111
5.95
7
8.05
mA/CH
A
Leakage Current
Any output; B3B2B1 = 000; No
Input
0.5
µA
A
2
VD
V
A
20
µA
A
0
0.4
V
A
20
µA
A
pF
C
LOGIC INPUTS
Logic High Input Voltage; VIH
Logic High Input Current; IIH
Logic Low Input Voltage; VIL
Logic Low Input Current; IIL Input
Capacitance, CIN
5
POWER DISSIPATION
All channels
Power-Down Dissipation
B3B2B1 = 000; no signal
Total Power Dissipation
200
µW
A
B3B2B1 = 001; no signal
80
92
mW
A
B3B2B1 = 111; no signal
560
644
mW
A
90
V
A
AC SPECIFICATIONS
Input Amplitude, VIN
Insertion loss, IL
1 µs positive and negative pulse
applied seperately at
PRF = 10 kHz
-90
CW mode (continuous wave)
-10
10
V
B
B3B2B1 = 111
-0.9
-1.8
dB
A
B3B2B1 = 100
-1.1
-1.8
dB
A
B3B2B1 = 001
-1.3
-2
dB
A
B3B2B1 = 111, RLOAD = 50Ω
-4.1
dB
B
-7
dB
B
Channel to channel IL matching
B3B2B1 = 001, RLOAD = 50Ω
B3B2B1 = 111
0.06
dB
B
Insertion Loss, IL
B3B2B1 = 111, at 20MHz
-0.9
dB
B
B3B2B1 = 111, RLOAD = 50 Ω
30
Ω
B
B3B2B1 = 001, RLOAD = 50 Ω
62
Ω
B
B3B2B1 = 111
44
Ω
B
B3B2B1 = 001
67
Ω
B
B3B2B1 = 111
140
MHz
B
B3B2B1 = 100
115
MHz
B
B3B2B1 = 001
65
MHz
B
B3B2B1 = 111, VIN = 0.5VPP
5MHz
-74
dBc
B
B3B2B1 = 100, VIN = 0.5VPP
5MHz
-74
dBc
B
B3B2B1 = 001, VIN = 0.5VPP
5MHz
-73
dBc
B
Equivalent Resistance, RON
-3dB Bandwidth, BW
2nd Harmonic Distortion, HD2, 5MHz
4
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
TX810
www.ti.com
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
ELECTRICAL CHARACTERISTICS (continued)
All Specifications at TA = 25°C, VP = 5V, VN = -5V, VB = 0V, Vsub= -5V, RLOAD = 400Ω; f = 5MHz, B3B2B1 = 111, VIN =
0.25VPP, unless otherwise noted. Test Level: A: Final tester limits; B: bench evaluation/simulation; C: Simulation
PARAMETER
TEST CONDITIONS
2nd Harmonic Distortion, HD2, 10MHz
Cross-talk, Xtalk
3rd order Intermodulation, IMD3
(1)
Power Supply Modulation Ratio, PSMR
(2)
Power Supply Rejection Ratio, PSRR
Input Referred Noise, IRN
Recovery Time 140 VPP IN, VOUT < 20mVPP
Turn-on Delay Time
Turn-off Delay Time
(3)
, tEN_ON
(3)
, tEN_OFF
Bias Current Switching Time
Propagation Delay Time
(3)
, tDELAY
Clamp Voltage, excludes overshoot
(1)
(2)
(3)
MIN
TYP
MAX
UNIT
Test
Level
B3B2B1 = 111, VIN = 0.5 VPP
10MHz
-78
dBc
B
B3B2B1 = 100, VIN = 0.5 VPP
10MHz
-77
dBc
B
B3B2B1 = 001, VIN = 0.5 VPP
10MHz
-74
dBc
B
B3B2B1 = 111 at 10MHz
-70
dBc
B
B3B2B1 = 100 at 10MHz
-69
dBc
B
B3B2B1 = 001 at 10MHz
-61
dBc
B
B3B2B1 = 111
-68
dBc
B
B3B2B1 = 100
-65
dBc
B
B3B2B1 = 001
-50
dBc
B
B3B2B1 = 111
-76
dBc
B
B3B2B1 = 100
-76
dBc
B
B3B2B1 = 001
-76
dBc
B
B3B2B1 = 111, 1KHz and 1MHz
-64
dBc
B
B3B2B1 = 111
0.91
nV/rtHz
B
B3B2B1 = 100
1.05
nV/rtHz
B
B3B2B1 = 001
1.12
nV/rtHz
B
B3B2B1 = 111
1
µs
B
B3B2B1 = 100
0.5
µs
B
B3B2B1 = 001
0.3
µs
B
B3B2B1 = 000→111
0.6
µs
B
B3B2B1 = 000→100
0.5
µs
B
B3B2B1 = 000→001
0.5
µs
B
B3B2B1 = 111→000
2.4
µs
B
B3B2B1 = 100→000
2.7
µs
B
B3B2B1 = 001→000
2.2
µs
B
B3B2B1 = 001→111
0.7
µs
B
B3B2B1 = 111
1.3
ns
B
B3B2B1 = 100
1.6
ns
B
B3B2B1 = 001
1.7
ns
B
B3B2B1 = 111
1.9
VPP
B
B3B2B1 = 001
1.7
VPP
B
B3B2B1 = 000
1.4
VPP
B
5MHz 1VPP, and 5.01MHz 0.5VPP input.
PSMR is defined as the ratio between carrier 5MHz and side band signals with 1KHz and 1MHz 50mVPP Noise applied on supply pins.
See the timing diagram show in Figure 2.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
5
TX810
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
www.ti.com
INPUT
tEN_ON
tEN_OFF
tDELAY
B3/B2/B1
OUTPUT
Figure 2. Timing Diagram
TYPICAL CHARACTERISTICS
All Specifications at TA = 25°C, VP = 5V, VN = -5V, VB = 0V, VSUB = -5V, RIN = 75Ω, RLOAD = 400Ω;
f = 5MHz, B3B2B1=111, VIN = 0.25VPP, unless otherwise noted.
A typical bench setup is shown in Figure 3.
VP
1 Channel
of TX810
Signal
Source
Test
Equipment
RIN
RLOAD
VN
Figure 3. Typical Test Setup
Bias = 7 mA
300
Unit Amount
80
1.5
Output Amplitude − V
350
100
2
1890 Units,
Bias = 7 mA,
RIN = N/A
250
200
150
100
Input
60
1
40
Output
0.5
20
0
0
-20
-0.5
-40
-1
-60
-1.5
50
-0.85
-0.86
-0.87
-0.88
-0.89
-0.9
-0.91
-0.92
-0.93
-0.94
-0.95
0
Input Amplitude − V
400
-80
-2
-0.5
-100
0
0.5
1
1.5
2
2.5
3
t − Time − ms
Insertion Loss − dB
AC coupling is used between High voltage pulser and TX810. The
input signal is a combination of 0.25Vpp signal followed by a 1-cycle
140Vpp pulse
Figure 4. Insertion Loss Distribution
6
Figure 5. Recovery Time With Small Input Signal
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
TX810
www.ti.com
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS (continued)
All Specifications at TA = 25°C, VP = 5V, VN = -5V, VB = 0V, VSUB = -5V, RIN = 75Ω, RLOAD = 400Ω;
f = 5MHz, B3B2B1=111, VIN = 0.25VPP, unless otherwise noted.
100
0.05
Bias = 7 mA,
RLOAD = 50 W
-60
80
-62
60
0.02
40
Input
20
0.01
0
0
-20
-0.01
Output
-0.02
-40
-64
Crosstalk − dBc
0.03
Input Amplitude − V
Output Amplitude − V
0.04
-66
5MHz
-68
-70
10MHz
-60
-0.03
-72
-80
-0.04
-0.05
-5
0
5
10
15
20
-100
30
25
-74
2
1
3
t − Time − ms
4
5
7
6
Bias Current − mA
AC coupling is used between High voltage pulser and TX810. The
input signal is a 1-cycle 140Vpp pulse
Figure 6. Recovery Time Without Signal
Figure 7. Cross-talk vs. Bias Currents vs. Frequency
-60
1.4
-66
-68
-70
5MHz
-72
1.2
Input Referred Noise − nV/√Hz
VIN = 500 mVPP
-64
-74
-76
10MHz
-78
10MHz
1
1MHz
0.8
5MHz
0.6
0.4
0.2
-80
0
1
2
3
4
5
6
7
2
1
3
Bias Current − mA
Figure 8. HD2 vs. Bias Current vs. Frequency
0.3
7
5
0
2
1
-0.1
0
4
0.1
Amplitude − V
3
5
0.2
Trigger Amplitude − V
4
0.1
6
Trigger
Trigger
0.2
Output Amplitude − V
6
5
Figure 9. Input Referred Noise vs. Bias Current vs. Frequency
6
0.3
4
Bias Current − mA
3
0
2
-0.1
1
TX810 Output
-0.2
-0.2
TX810 Output
-2
0
0.5
1
1.5
2
2.5
3
0
-1
-0.3
3.5
4
Trigger Amplitude − V
2nd Harmonic Distortion − dBc
-62
-0.3
-1
0
1
2
3
4
5
6
7
8
t − Time − ms
t − Time − ms
Figure 10. Power On Response Time (0mA to 7mA)
Figure 11. Power Down Response Time (7mA to 0mA)
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
7
TX810
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
All Specifications at TA = 25°C, VP = 5V, VN = -5V, VB = 0V, VSUB = -5V, RIN = 75Ω, RLOAD = 400Ω;
f = 5MHz, B3B2B1=111, VIN = 0.25VPP, unless otherwise noted.
5
0.2
Trigger
0.15
4
0.1
Amplitude − V
0.05
3
0
-0.5
2
-0.1
1
-0.15
TX810 Output
-0.2
0
-0.25
-0.3
-1
0
0.5
1
1.5
2
2.5
3
3.5
4
t − Time − ms
Figure 12. Bias Current Adjustment Response Time (1mA to 7mA)
8
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
TX810
www.ti.com
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
THEORY OF OPERATION
A typical ultrasound block diagram is shown in Figure 13.
Figure 13. Ultrasound System Block Diagram
A transducer is excited by high voltage pulsers. It converts the electrical energy to mechanical energy. After each
excitation, the transducer sends out ultrasonic wave to medium. Partial ultrasonic wave gets reflected by
inhomogeneous medium and received by the transducer again, i.e. echo signal. Thus, the transducer is a duplex
device on which both high voltage and low voltage signals exist. The transducer can not be connected to
amplifier stages directly; otherwise, the high voltage signal can permanently destroy amplifiers. The TX810, i.e.
T/R switches, is sitting between integrated HV pulser and low noise amplifier (LNA). The main function of TX810
is to isolate the LNA from high-voltage transmitter. TX810 limits the high voltage pulse and let echo signals
reaching amplifier. Therefore, an ideal T/R switch should completely block high voltage signals and maintain all
information from echoes.
The detail architecture of the TX810 is listed in Figure 14.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
9
TX810
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
www.ti.com
VP
D1
D0
D3
D2
D4
D6
D5
1 Channel
of TX810
HV TX
LV RX
D0~D6 is determined by
B1~B3 pins
RLOAD
L
VB
D0
D1
D3
D2
D4
D6
D5
VN
Figure 14. TX810 Block Diagram
TX810 includes four parts: Diode Bridge, bias network, clamp diodes, and logic controller. A decoder is used to
convert 3-bit logic (B1 to B3) input to 7 control signals (D0 to D6) for 7 MOSFET switches. +2.5V to +5V logic
input is level shifted internally to drive the switches. The bias current of the bridge diode is adjusted
proportionally by these switches. When all switches are on, the bias current is 7mA. Each bit difference will
adjust the bias current approximately 1mA. When all switches are off, the TX810 enters the power down mode.
Comparing to discrete T/R switches, TX810 can be shut down and turned on quickly as shown in the typical
characteristics plots. Considering the low duty cycle of ultrasound imaging, significant power saving can be
achieved.
All 6 diodes are high-voltage Schottky diodes to achieve fast recovery time. Following the bridge, a pair of
back-to-back diode limits the output voltage of TX810 to about 2Vpp. Different power/performance combination
can be selected by users. The TX810 is specified to operate at ±5V and VB is biased at 0V. The characteristics
of the T/R switch are mainly determined by bias currents. Lower power can be achieved with lower supply
voltages. Also, Table 1 shows the relationship among bias current, insertion loss, input noise, power
consumption and equivalent resistance.
Table 1. Bias current vs Performance
Test Conditions: VP = 5V, VN = -5V; VB = 0V; RLOAD = 50Ω
10
B3
B2
B1
I (mA)
IL (dB)
IRN (nV/rtHz)
RON (Ω)
0
0
0
0
N/A
N/A
High Impedance
0
0
0
1
1
-7
1.12
62
10
0
1
0
2
-5.6
1.10
45
20
0
1
1
3
-5
1.09
39
30
1
0
0
4
-4.6
1.05
35
40
1
0
1
5
-4.4
0.99
33
50
1
1
0
6
-4.2
0.95
31
60
1
1
1
7
-4.1
0.91
30
70
Submit Documentation Feedback
Power (mW/CH)
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
TX810
www.ti.com
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
APPLICATION INFORMATION
Similar to discrete T/R switch solutions, external components can be used to optimize system performance.
Inductor L and resistor RLOAD before the low voltage receiver amplifier (LVRx) can improve overload recovery
time and reduce reflection. The L acts as a high pass filter thus overshoot or recovery response spikes can be
suppressed to minimal. The L and RLOAD terminate the entire signal path and can reduce reflection; therefore
axial resolution in ultrasound image might be improved. However, the combined impedance of L and RLOAD may
affect the system sensitivity. The insertion loss of T/R switch is determined by the input impedance of receiver
amplifier and RON of the TX810. L also creates a DC path for any offset caused by mismatching.The inductor can
be as low as 10s µH to suppress low frequency signals from transmitter, transducer, multiplexer, and TX810. The
optimization of L and RLOAD is always an important topic for system designers. AC coupling are typically used
between transmitter and T/R switch or T/R switch and amplifier. Thus amplifiers with DC biased inputs will not
interference with T/R switch.
One challenge for integrating multiple channel circuits on a small package is how to reduce cross talk. In
ultrasound systems, acoustic cross talk from adjacent transducer elements is a dominant source. The cross talk
from transducer elements is in a range of -30 to -35dBc for array transducers. Circuit cross talk is usually at least
20dB better than the transducer cross talk. The special considerations were implemented in both TX810 design
and layout. The cross talk among TX810 channels is reduced to below -60 dBc as show in the specification
table.
In ultrasound Doppler applications, modulation effect in system can influence image quality and sensitivity.
Ultrasound system is a complex mixed-signal system with all kinds of digital and analog circuits. Digital signals
and clock signals can contaminate analog signals on system level or on chip level. Nonlinear components, such
as transistors and diodes, can modulate noise and contaminate signals. In Doppler applications, the Doppler
signal frequency could range from 20Hz to >50KHz. Meanwhile, multiple system clocks are also in this range,
such as frame clock, image line clock, and etc. These noise signals could enter chip through ground and power
supply pins. It is important to study the power supply modulation ratio (PSMR) at chip level. Noise signal with
certain frequency and amplitude can be applied on supply pins. Side band signals could be found if modulation
effect exists. The PSMR is expressed as an amplitude ratio between carrier and side band signals. Beside
PSMR, 3rd order intermodulation ratio (IMD3) is a standard specification for mixed-signal ICs. Users can use
IMD3 to estimate the potential artifact Doppler mirror signals. Both specs can be found in the specification table.
The schematic of the basic connection for TX810 is shown in Figure 15. Optional inductors and resistors can be
used at TX810 outputs depending on transducer characteristics as discussed above. Standard decoupling
capacitors 0.1µF should be placed close to power supply pins. The pin out of TX810 is optimized for PCB layout.
All signals are going from left to right straightly.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
11
TX810
SLLS996A – SEPTEMBER 2009 – REVISED APRIL 2010
www.ti.com
TX CH8
3.3V
RX CH8
5V
0.1uF
0.1uF
Optional
0.1uF
0.1uF
Optional
0.1uF
0.1uF
Optional
TX CH7
0.1uF
OUT7
GND
VP
OUT8
VD
GND
IN8
IN7
TX CH6
GND
RX CH7
IN6
OUT6
GND
GND
OUT5
IN5
NC
NC
NC
0.1uF
TX CH3
B2
B3
IN4
OUT4
GND
GND
IN3
OUT3
VN
VB
GND
IN1
IN2
GND
0.1uF
B1
Pull Down
20K×3
Optional
B2
B3
RX CH4
0.1uF
Optional
0.1uF
Optional
0.1uF
Optional
0.1uF
Optional
RX CH3
OUT2
TX CH4
RX CH5
B1
GND
0.1uF
TX810
PowerPAD
Vsub
(-5V)
OUT1
TX CH5
RX CH6
TX CH2
RX CH2
0.1uF
5V
TX CH1
0.1uF
RX CH1
Figure 15. Schematic of TX810
SPACER
REVISION HISTORY
Changes from Original (September 2009) to Revision A
•
12
Page
Changed From: Product Preview To: Production. The Product Preview was a two page data sheet containing the
front page and the pin out section ........................................................................................................................................ 1
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s) :TX810
PACKAGE OPTION ADDENDUM
www.ti.com
2-Apr-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TX810IRHHR
ACTIVE
VQFN
RHH
36
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TX810IRHHT
ACTIVE
VQFN
RHH
36
250
CU NIPDAU
Level-2-260C-1 YEAR
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jul-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TX810IRHHR
VQFN
RHH
36
2500
330.0
16.4
6.3
6.3
1.5
12.0
16.0
Q2
TX810IRHHT
VQFN
RHH
36
250
330.0
16.4
6.3
6.3
1.5
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
20-Jul-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TX810IRHHR
VQFN
RHH
36
2500
333.2
345.9
28.6
TX810IRHHT
VQFN
RHH
36
250
333.2
345.9
28.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated