TPS61150A www.ti.com SLVS706 – OCTOBER 2006 DUAL OUTPUT BOOST WLED DRIVER USING SINGLE INDUCTOR FEATURES • • • • • • • • • • • • 2.5V to 6V Input Voltage Range 0.7A Integrated Switch Built-in Power Diode 1.2MHz Fixed PWM Frequency Individually Programmable Output Current Input-to-Output Isolation Built-in Soft Start 27V Overvoltage Protection 3% at 15mA Matching between Two Current Strings, Improvement from TPS61150/1 Up to 83% Efficiency Up to 30kHz PWM Dimming Frequency Availiable in a 10 Pin, 3 × 3 mm QFN Package APPLICATIONS • • • Up to 14 WLED Driver for Media Form Factor Display Sub and Main Display Backlight in Clam Shell Phones Display and Keypad Backlight in Portable Equipment The two current outputs are ideal for driving WLED backlight for the sub and main displays in clam shell phones. The two outputs can also be used for driving display and keypad backlights. When used together, the two outputs can drive up to 14 WLED for one large display. In addition to the small inductor, small capacitor and 3mm x 3mm QFN package, the built-in MOSFET and diode eliminate the need for any external power devices. Overall, the IC provides an extremely compact solution with high efficiency and plenty of flexibility. TYPICAL APPLICATION 2.5V to 6V Input L1 10mH C1 1mF SW IOUT VIN C2 1mF GND TPS61150A SEL1 IFB1 SEL2 IFB2 ISET1 DESCRIPTION R1 56.5kW ISET2 R2 56.5kW The TPS61150A is a high frequency boost converter with two regulated current outputs for driving WLEDs. Each current output can be individually programmed through external resistors. There is dedicated selection pin for each output, so the two outputs can be turned on separately or simultaneously. The output current can be reduced by a pulse width modulation (PWM) signal on the select pins or an analog voltage on the ISET pin. The boost regulator runs at 1.2MHz fixed switching frequency to reduce output ripple and avoid audible noises associated with PFM control. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006, Texas Instruments Incorporated TPS61150A www.ti.com SLVS706 – OCTOBER 2006 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION (1) (1) TA PACKAGE OVP (Typ.) PACKAGE MARKING –40 to 85°C TPS61150ADRCR 28V BTK –40 to 85°C TPS61150ADRCT 28V BTK For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. DEVICE INFORMATION QFN PACKAGE (TOP VIEW) IFB1 1 ISET 2 SEL1 3 SEL2 VIN 10 IFB2 9 ISET2 8 GND 4 7 IOUT 5 6 SW Exposed Thermal Pad TERMINAL FUNCTIONS TERMINAL NAME NO. I/O DESCRIPTION VIN 5 I Input pin. VIN provides the current to the boost power stage, and also powers the IC circuit. When VIN is below the undervoltage lockout threshold, the IC turns off and disables outputs; thereby disconnecting the WLEDs from the input. GND 8 O Ground. Connect the input and output capacitors as close as possible to this pin. SW 6 I Switching node of the IC. IOUT 7 O Constant current supply output. IOUT is directly connected to the boost converter output. IFB1, IFB2 10 I Return path for the IOUT regulation. The current regulator is connected to this pin, and it can be disabled to open the current path. ISET1, ISET2 2 9 I Output current programming. The resistor connected to the pin programs the corresponding output current. SEL1, SEL2 3 4 I Mode selection. See Table 1 for details. Thermal Pad The thermal pad should be soldered to the analog ground. If possible, use the thermal pad to connect to ground plane for ideal power dissipation. Table 1. TPS61150A Mode Selection SEL1 2 SEL2 IFB1 IFB2 H L Enable Disable L H Disable Enable H H Enable Enable L L IC Shutdown Submit Documentation Feedback TPS61150A www.ti.com SLVS706 – OCTOBER 2006 FUNCTIONAL BLOCK DIAGRAM SW IOUT VIN + − 1.2MHz Current Mode Control PWM GND IFB1 Current Sink SEL1 0.33V ISET1 Error Amplifier IFB2 TPS61150A SEL2 Current Sink ISET2 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE UNIT Supply voltages on pin VIN (2) –0.3 to 7 V Voltages on pins SEL1/2, ISET1/2 (2) –0.3 to 7 V 30 V Voltage on pin IOUT, SW, IFB1 and IFB2 (2) Continuous power dissipation See Dissipation Rating Table Operating junction temperature range –40 to 150 °C Storage temperature range –65 to 150 °C 260 °C Lead Temperature (soldering, 10 sec) (1) (2) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to network ground terminal. DISSIPATION RATINGS PACKAGE QFN (1) QFN (2)(2 (1) (2) RθJA TA≤ 25°C POWER RATING TA = 70°C POWER RATING TA = 85°C POWER RATING 270oC/W 370mW 204mW 148mW 48.7oC/W 2.05W 1.13W 821mW Soldered PowerPAD on a standard 2-layer PCB without vias for thermal pad. Soldered PowerPAD on a standard 4-layer PCB with vias for thermal pad . Submit Documentation Feedback 3 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT Input voltage range 2.5 6.0 V VO Output voltage range VIN 27 V L Inductor (1) CI Input capacitor (1) 1 µF CO Output capacitor (1) 1 µF TA Operating ambient temperature –40 85 °C TJ Operating junction temperature –40 125 °C (1) 4 NOM VI µH 10 See Application Section for further information. Submit Documentation Feedback TPS61150A www.ti.com SLVS706 – OCTOBER 2006 ELECTRICAL CHARACTERISTICS VIN = 3.6V, SELx = VIN, Rset = 80kΩ, V(IOUT) = 15V, TA = –40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT VI Input voltage range IQ Operating quiescent current into VIN Device PWM switching no load ISD Shutdown current SELx = GND, TA = 25°C SELx = GND VUVLO Under-voltage lockout threshold Vhys Under-voltage lockout hysterisis 2.5 VIN falling 6.0 V 2 mA 1.7 1.9 µA 2.7 3 1.65 1.8 70 V mV ENABLE AND SOFT START V(selh) SEL logic high voltage VI = 2.5V to 6V V(sell) SEL logic low voltage VI = 2.5V to 6V R(en) SEL pull down resistor t(off) SEL pulse width to disable I(ss) IFB soft start current steps t(ss) Soft start time step Measured as clock divider t(ss_en) Soft start enable time Time between falling and rising of two adjacent SELx pulses 1.2 0.4 300 SELx high to low V 700 V kΩ 40 ms 16 64 40 ms CURRENT FEEDBACK V(ISET) ISET pin voltage KISET Current multipler, Ifb1/Iset1 , Ifb2/Iset2 1.204 1.229 1.254 ISET current = 16.7µA 883 920 957 KM Current matching, (2×|Ifb1–Ifb2|)/(Ifb1+Ifb2) ISET current = 16.7µA ISET current = 1.2µA 736 920 1104 ISET current = 1.2µA V(IFB) IFB regulation voltage Vhys(IFB_L) IFB low threshold hysteresis tI(sink) Current sink settle time measured from SELx rising edge (1) Ilkg IFB pin leakage current 0% 3% 0% 20% 300 330 360 60 IFB voltage = 25V V mV mV 6 µs 1 µA POWER SWITCH AND DIODE RDS(ON) N-channel MOSFET on-resistance VIN = VGS = 3.6V Ilkg(N_NFET) N-channel leakage current VDS = 25V V(F) Diode current = 0.7A Power diode forward voltage 0.9 Ω 1 µA 0.83 1.0 V 0.6 OC AND OVP IL N-Channel MOSFET current limit I(IFB_MAX) Current sink max output current Vovp Overvoltage threshold Vovp_hys Overvoltage hysteresis Dual output, IOUT= 15V, Duty cycle = 76% 0.75 1.0 1.25 Single output , IOUT= 15V, Duty cycle = 76% 0.40 0.55 0.7 28 29 IFB current = 330mV 34 27 A mA 550 V mV PWM AND PFM CONTROL FS Oscillator frequency Dmax Maximum duty cycle Feedback voltage = 1.0V 1.0 1.2 89% 93% 1.5 MHz THERMAL SHUTDOWN Tshutdown Thermal shutdown threshold Thys Thermal shutdown threshold hysteresis (1) 160 °C 15 °C This specification determines the minimum on time required for PWM dimming for desirable linearity. The maximum PWM dimming frequency can be calculated from the minimum duty cycle required in the application. Submit Documentation Feedback 5 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 TYPICAL CHARACTERISTICS Table of Graphs FIGURES Overcurrent Limit VIN = 3.0V, 3.6V, and 4.2V, single and dual output 1,2 WLED efficiency VIN = 3.3V, 3.6V and 4.2V, 3 WLED, WLED voltage = 11V 3 WLED efficiency VIN = 3.3V, 3.6V and 4.2V, 4 WLED, WLED voltage = 15V 4 WLED efficiency VIN = 3.3V, 3.6V and 4.2V, 5 WLED, WLED voltage = 19V 5 WLED efficiency VIN = 3.3V, 3.6V and 4.2V, 6 WLED, WLED voltage = 23V 6 Both on efficiency VIN = 3.3V, 3.6V and 4.2V, 4 WLED on each output 7 K value over current VIN = 3.6V, IWLED = 1mA to 25mA 8 PWM dimming linearity Frequency = 20kHz and 30kHz 9 Single output PWM dimming waveform 10 Multiplexed PWM dimming waveform 11 Start up waveform 12 OVERCURRENT LIMIT (SINGLE OUTPUT) vs DUTY CYCLE OVERCURRENT LIMIT (DUAL OUTPUT) vs DUTY CYCLE 1200 600 VI = 4.2V VI = 3V 1000 VI = 3.6V Current Limit - mA Current Limit - mA 500 400 VI = 3V 300 200 800 VI = 3.6V 400 200 100 0 0 10 20 30 40 50 60 Duty Cycle - % 70 80 90 10 20 30 40 50 60 Duty Cycle - % Figure 1. 6 VI = 4.2V 600 Figure 2. Submit Documentation Feedback 70 80 90 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 EFFICIENCY vs LOAD CURRENT EFFICIENCY vs LOAD CURRENT 90 90 WLED Voltage = 15V , 4 WLED, Single Output WLED Voltage = 11V , 3 WLED, Single Output VI = 3.6V 80 Efficiency - % Efficiency - % 80 VI = 3.3V 70 60 VI = 4.2V VI = 3.3V 70 VI = 3.6V 60 VI = 4.2V 50 50 0 5 10 15 20 0 25 5 Figure 4. EFFICIENCY vs LOAD CURRENT EFFICIENCY vs LOAD CURRENT 25 20 25 WLED Voltage = 23V , 6 WLED, Single Output VI = 4.2V VI = 4.2V 80 VI = 3.6V 70 20 90 Efficiency - % Efficiency - % Figure 3. WLED Voltage = 19V , 5 WLED, Single Output 80 15 WLED Current - mA WLED Current - mA 90 10 VI = 3.3V 60 70 VI = 3.6V VI = 3.3V 60 50 0 5 10 15 WLED Current - mA 20 25 50 0 5 10 15 WLED Current - mA Figure 5. Figure 6. Submit Documentation Feedback 7 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 BOTH ON EFFICIENCY vs TOTAL OUTPUT CURRENT K VALUE vs WLED CURRENT 1200 90 VI = 3.6V WLED1 Voltage = 15V WLED2 Voltage = 15V WLED1 Voltage = 15V WLED2 Voltage = 15V 1100 VI = 3.3V 1000 VI = 3.6V 70 K Value Efficiency - % 80 VI = 4.2V WLED1 900 WLED2 60 800 700 50 0 10 20 30 40 50 IO - Total Output Current - mA 60 0 10 20 30 WLED Current - mA 40 Figure 7. Figure 8. WLED BRIGHTNESS DIMMING LINEARITY SINGLE OUTPUT WLED PWM BRIGHTNESS DIMMING 50 25 ISEL2 5V/div , DC WLED current - mA 20 SW 10V/div , DC 15 IOUT 1V/div , DC 10 15V Offset WLED Current f = 20kHz 20mA/div, DC 5 t - Time - 20ms/div f = 30kHz 0 0 20 40 60 PWM Duty cycle - % 80 100 Figure 9. 8 Figure 10. Submit Documentation Feedback TPS61150A www.ti.com SLVS706 – OCTOBER 2006 MULTIPLEXED PWM DIMMING (ISEL1: 4 WLED, ISEL2: 2 WLED) WLED START UP ISEL1 ISEL2 5V/div , DC ISEL2 5V/div , DC IOUT 10V/div , DC 5V/div , DC Inductor Current 500mA/div , DC WLED Current 20mA/div , DC IOUT 5V/div , DC t - Time - 200ms/div t - Time - 2ms/div Figure 11. Figure 12. Submit Documentation Feedback 9 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 DETAILED DESCRIPTION CURRENT REGULATION The TPS61150A uses a single boost regulator to drive 2 WLED strings whose current can be programmed independently. The boost converter adopts PWM control which is ideal for high output current and low output ripple noises. The feedback loop regulates the IFB pin to a threshold voltage (330mV typical), giving the current sink circuit just enough headroom to operate. The regulation current is set by the resistor on the Iset pin based on V I O + ISET KISET RSET (1) where IO = output current VISET = Iset pin voltage (1.229V typical) RSET = Iset pin resistor value KISET = current multiplier (920 typical) When both outputs are enabled, the boost converter regulates to the IFB pin that demands higher Iout pin voltage, V(IOUT), and let the other IFB pin rise above its regulation voltage. The feedback path dynamically switches to the other IFB pin if its voltage drops more than the IFB low hysterisis (60mV typical) below it's regulation voltage. This ensures proper current regulation for both outputs. When both IFB voltages are low, IFB1 is used for regulation. Once IFB1 reaches its regulation voltage, the feedback path may hand over to IFB2 if it is still low, and the boost output will continue to rise. The overall efficiency in this mode depends on the voltage different between the IFB1 and IFB2. A large difference reduces the efficiency due to power losses across the current sink circuit. To improve the efficiency of the both-on mode, the two current outputs can be turned on complimentarily by applying out of phase enable signal to the SEL pins. The ISET pin resistors need to be recalculated to compensate for the reduced DC current. START UP During start up, both the boost converter and the current sink circuitry are trying to establish steady state simultaneously. The current sink circuitry ramps up current in 16 steps, with each step taking 64 clock cycles. This ensures that the current sink loop is slower than the boost converter response during startup. Therefore, the boost converter output comes up slowly as current sink circuitry ramps up the current. This ensures smooth start up and minimizes in-rush current. OVERVOLTAGE PROTECTION To prevent the boost output run away as the result of WLED disconnection, there is an overvoltage protection circuit which stops the boost converter from switching as soon as its output exceeds the OVP threshold. When the voltage falls below the OVP threshold, the converter resumes switching. TPS61150A provides 28V(typical) OVP to prevent a 25V rated output capacitor or the internal 30V FET from breaking down. UNDERVOLTAGE LOCKOUT An undervoltage lockout prevents mis-operation of the device for input voltages below 1.65V (typical). When the input voltage is below the undervoltage threshold, the device remains off and both the boost converter and current sink circuit are turned off, providing isolation between input and output. THERMAL SHUTDOWN An internal thermal shutdown turns off the IC when the typical junction temperature of 160°C is exceeded. The thermal shutdown has a hysteresis of typically 15°C. 10 Submit Documentation Feedback TPS61150A www.ti.com SLVS706 – OCTOBER 2006 DETAILED DESCRIPTION (continued) ENABLE Pulling either the SEL1 or SEL2 pin low turns off the corresponding output. If both SEL1 and SEL2 are low for more than 40ms, the IC shuts down and consumes less than 2µA (room temperature) current. The SEL pin can also be used for PWM brightness dimming. To improve PWM dimming linearity, soft start is disabled if the time between falling and rising edges of two adjacent SELx pulses is less than 40ms. See APPLICATION INFORMATION for details. Each SEL input pin has an internal pull down resistor to disable the device when the pin is floating. Submit Documentation Feedback 11 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 APPLICATION INFORMATION MAXIMUM OUTPUT CURRENT The over-current limit in a boost converter limits the maximum input current and thus maximum input power for a given input voltage. Maximum output power is less than maximum input power due to power conversion losses. Therefore, the current limit, input voltage, output voltage and efficiency can all change maximum current output. Since current limit clamps peak inductor current, ripple has to be subtracted to derive maximum DC current. The ripple current is a function of switching frequency, inductor value and duty cycle. The following equations take into account of all the above factors for maximum output current calculation. 1 Ip + 1 L ) 1 Fs Viout)Vf*Vin Vin (2) ƪ ǒ Ǔ ƫ where Ip = inductor peak-to-peak ripple L = inductor value Vf = power diode forward voltage Fs = switching frequency Viout = boost output voltage. It is equal to 330mV + voltage drop across WLED. Vin Iout_max + ǒ Ilim * Ip 2 Ǔ h Viout (3) where Iout_max = maximum output current of the boost converter Ilim = overcurrent limit η = efficiency To keep a tight range of the overcurrent limit, The TPS61150A uses the Vin and Iout pin voltage to compensate for the overcurrent limit variation caused by the slope compensation. However, the current threshold still has residual dependency on the VIN and IOUT voltage. Use Figure 1 and Figure 2 to identify the typical overcurrent limit in your application, and use ±25% tolerance to account for temperature dependency and process variations. The maximum output current can also be limited by the current capability of the current sink circuitry. It is designed to provide maximum 35mA current regardless of the current capability of the boost converter. WLED BRIGHTNESS DIMMING There are three ways to change the output current on the fly for WLED dimming. The first method parallels an additional resistor with the ISET pin resistor as shown in Figure 13 . The switch (Q1) can change the ISET pin resistance and therefore, modify the output current. This method is very simple, but can only provide limited dimming steps. ISET R1 RISET Q1 ON/OFF Logic Figure 13. Switching In/Out an Additional Resistor to Change Output Current 12 Submit Documentation Feedback TPS61150A www.ti.com SLVS706 – OCTOBER 2006 APPLICATION INFORMATION (continued) Alternatively, a PWM dimming signal at the SEL pin can modulate the output current by the duty cycle of the signal. The logic high of the signal turns on the current sink circuit, while the logic low turns it off. This operation creates an averaged DC output current proportional to the duty cycle of the PWM signal. The frequency of the PWM signal has to be high enough to avoid flashing of the WLEDs. The soft start of the current sink circuit is disabled during the PWM dimming to improve linearity. The major concern of the PWM dimming is the creation of audible noises which can come from the inductor and/or output capacitor of the boost converter. The audible noises on the output capacitor are created by the presence of voltage ripple in range of audible frequencies. The TPS61150A alleviates the problem by disconnecting the WLEDs from the output capacitor when the SEL pin is low. Therefore, the output capacitor is not discharged by the WLEDs, which reduces the voltage ripple during PWM dimming. The audible noises can be eliminated by using PWM dimming frequency above or below the audible frequency range. The maximum PWM dimming frequency of the TPS61150A is determined by the current settling time (tisink) which is the time required for the circuit sink circuit to reach steady state after the SEL pin transitions from low to high. The maximum dimming frequency can be calculated by D F PWM_MAX + T min isink (4) Dmin = min duty cycle of the PWM dimming required in the application. For 20% Dmin, PWM dimming frequency up to 33kHz is possible, making the noise frequency above the audible range. The third method uses an external DC voltage and resistor as shown in Figure 14 to change the ISET pin current, and thus control the output current. The DC voltage can be the output of a filtered PWM signal. The equation to calculate the output current is I I WLED WLED +K +K ǒ ǒ 1.229 ) R ISET ISET 1.229 * V R1 Ǔ Ǔ DC 1.229 * V 1.229 ) DC R R 1 ) 10K ISET ISET for DC voltage input (5) for PWM signal input (6) KISET = current multiplier between the ISET pin current and the IFB pin current. VDC= voltage of the DC voltage source or the DC voltage of the PWM signal. ISET ISET Filter PWM Signal R1 RISET DC Voltage 10 kW 0.1 mF R1 RISET Figure 14. Analog Dimming Uses an External Voltage Source to Control the Output Current INDUCTOR SELECTION Because the selection of the inductor affects power supplies steady state operation, transient behavior, and loop stability, the inductor is the most important component in power regulator design. There are three specifications most important to the performance of the inductor, inductor value, DC resistance, and saturation current. Considering inductor value alone is not enough. The inductors inductance value determines the inductor ripple current. It is generally recommended to set peak-to-peak ripple current given by Equation 2 to 30–40% of DC current. It is a good compromise of power losses and inductor size. For this reason, 10µH inductors are recommended for TPS61150A. Inductor DC current can be calculated as Submit Documentation Feedback 13 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 APPLICATION INFORMATION (continued) V I L_DC + iout V in I out h (7) Use the maximum load current and minimum VI for calculation. The internal loop compensation for PWM control is optimized for the external component shown in the typical application circuit with consideration of component tolerance. Inductor values can have ±20% tolerance with no current bias. When the inductor current approaches saturation level, its inductance can decrease 20 to 35% from the 0A value depending on how the inductor vendor defines saturation. Using an inductor with a smaller inductance value forces discontinuous PWM in which inductor current ramps down to zero before the end of each switching cycle. It reduces the boost converter’s maximum output current, and causes large input voltage ripple. An inductor with larger inductance reduces the gain and phase margin of the feedback loop, possibly resulting in instability Regulator efficiency is dependent on the resistance of its high current path and switching losses associated with the PWM switch and power diode. Although the TPS61150A has optimized the internal switches, the overall efficiency still relies on inductors DC resistance (DCR); Lower DCR improves efficiency. However, there is a trade off between DCR and inductor size, and shielded inductors typically have higher DCR than unshielded ones. DCR in range of 150mΩ to 350mΩ is suitable for applications requiring both on mode. DCR is the range of 250mΩ to 450mΩ is a good choice for single output application. Table 2 and Table 3 list recommended inductor models. Table 2. Recommended Inductors for Single Output L (µH) DCR Typ (mΩ) Isat (A) SIZE (L×W×H mm) VLF3012AT-100MR49 10 360 0.49 2.8×3.0×1.2 VLCF4018T-100MR74-2 10 163 0.74 4.0×4.0×1.8 CDRH2D11/HP 10 447 0.52 3.2×3.2×1.2 CDRH3D16/HP 10 230 0.84 4.0×4.0×1.8 TDK Sumida Table 3. Recommended Inductors for Dual Output L (µH) DCR Typ (mΩ) Isat (A) SIZE (L×W×H mm) VLCF4018T-100MR74-2 10 163 0.74 4.0×4.0×1.8 VLF4012AT-100MR79 10 300 0.85 3.5×3.7×1.2 CDRH3D16/HP 10 230 0.84 4.0×4.0×1.8 CDRH4D11/HP 10 340 0.85 4.8×4.8×1.2 TDK Sumida INPUT AND OUTPUT CAPACITOR SELECTION The output capacitor is mainly selected for the output ripple of the converter. This ripple voltage is the sum of the ripple caused by the capacitor’s capacitance and its equivalent series resistance (ESR). Assuming a capacitor with zero ESR, the minimum capacitance needed for a given ripple can be calculated by C out + ǒViout * VinǓ Iout V iout Fs V ripple (8) Vripple = Peak-to-peak output ripple. 14 Submit Documentation Feedback TPS61150A www.ti.com SLVS706 – OCTOBER 2006 For VI = 3.6V, Viout = 20V, and Fs = 1.2MHz, 0.1% ripple (20mV) would require 1.0µF capacitor. For this value, ceramic capacitors are the best choice for its size, cost and availability. The additional output ripple component caused by ESR is calculated using: Vripple_ESR = Iout× RESR Due to it's low ESR, Vripple_ESR can be neglected for ceramic capacitors, but must be considered if tantalum or electrolytic capacitors are used. During a load transient, the capacitor at the output of the boost converter has to supply or absorb additional current before the inductor current ramps up the steady state value. Larger capacitors always help to reduce the voltage over and under shoot during a load transient. A larger capacitor also helps loop stability. Care must be taken when evaluating a ceramic capacitor’s derating due to applied dc voltage, aging and frequency response. For example, larger form factor capacitors (in 1206 size) have their self-resonant frequencies in the range of TPS61150A’s switching frequency, so the effective capacitance is significantly lower. Therefore, it may be necessary to use small capacitors in parallel instead of one large capacitor. The popular vendors for high value ceramic capacitors are: TDK (http://www.component.tdk.com/components.php) Murata (http://www.murata.com/cap/index.html) Table 4. Recommended Input and Output Capacitors Capacitance (µF) Voltage (V) Case C3216X5R1E475K 4.7 25 1206 C2012X5R1E105K 1 25 805 C1005X5R0J105K 1 6.3 402 GRM319R61E475KA12D 4.7 25 1206 GRM216R61E105KA12D 1 25 805 GRM155R60J105KE19D 1 6.3 402 TDK Murata LAYOUT CONSIDERATION As for all switching power supplies, especially those providing high current and using high switching frequencies, layout is an important design step. If layout is not carefully done, the regulator could show instability as well as EMI problems, therefore, use wide and short traces for high current paths. The input capacitor needs not only to be close to the VIN pin, but also to the GND pin in order to reduce the input ripple seen by the IC. The VIN and SW pins are conveniently located on the edges of the IC, therefore the inductor can be placed close to the IC. The output capacitor needs to be placed near the load to minimize ripple and maximize transient performance. It is also beneficial to have the ground of the output capacitor close to the GND pin since there will be large ground return current flowing between them. When laying out signal ground, it is recommended to use short traces separated from power ground traces, and connect them together at a single point. Submit Documentation Feedback 15 TPS61150A www.ti.com SLVS706 – OCTOBER 2006 ADDITIONAL APPLICATION CIRCUIT L1 VIN C2 1mF 10mH VIN SW IOUT C2 1m F GND EN/PWM Dimming SEL1 SEL2 IFB1 IFB2 ISET1 ISET2 R1 R2 Figure 15. Driving Up to 12 WLEDs With One LCD Backlight Display VIN Keypad L1 10mH IFB1 ON C1 1mF IFB1 ON VIN SW IOUT SEL1 C2 1mF GND IFB2 ON SEL1 IFB2 ON SEL2 SEL2 40ms IC Shutdown ISET1 R1 IFB1 IFB2 ISET2 R2 Figure 16. Driving a Keypad and LCD Backlight by applying interleaved PWM signal to the SEL1 and SEL2 pins. The duty cycle of the PWM signal controls brightness dimming 16 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 5-Feb-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS61150ADRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS61150ADRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS61150ADRCT ACTIVE SON DRC 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS61150ADRCTG4 ACTIVE SON DRC 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 17-May-2007 Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS61150ADRCR DRC 10 MLA 330 12 3.3 3.3 1.1 8 12 PKGORN T2TR-MS P TPS61150ADRCT DRC 10 MLA 180 12 3.3 3.3 1.1 8 12 PKGORN T2TR-MS P TAPE AND REEL BOX INFORMATION Device Package Pins Site Length (mm) Width (mm) TPS61150ADRCR DRC 10 MLA 346.0 346.0 29.0 TPS61150ADRCT DRC 10 MLA 190.0 212.7 31.75 Pack Materials-Page 2 Height (mm) PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated