DSEK 60 Common Cathode Fast Recovery Epitaxial Diode (FRED) VRSM V 640 VRRM IFAVM = 2x 30 A VRRM = 600 V trr = 35 ns TO-247 AD Type V 600 A DSEK 60-06A C A C A A C (TAB) A = Anode, C = Cathode, TAB = Cathode Symbol Test Conditions Maximum Ratings IFRMS IFAVM ÿÿ① IFRM TVJ = TVJM TC = 85°C; rectangular, d = 0.5 tP < 10 ms; rep. rating, pulse width limited by TVJM 50 30 375 A A A ● IFSM TVJ = 45°C; t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine 300 320 A A ● TVJ = 150°C; t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine 260 280 A A TVJ = 45°C t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine 450 420 A2s A2s TVJ = 150°C; t = 10 ms (50 Hz), sine t = 8.3 ms (60 Hz), sine 340 320 A2s A2s -40...+150 150 -40...+150 °C °C °C 125 W Features ● ● ● TVJ TVJM Tstg ● Applications ● ● ● Ptot TC = 25°C Md Mounting torque 0.8...1.2 Weight Nm 6 g Advantages ● Symbol Test Conditions IR TVJ = 25°C TVJ = 25°C TVJ = 125°C VR = VRRM VR = 0.8 • VRRM VR = 0.8 • VRRM 100 50 7 mA mA mA Characteristic Values typ. max. VF IF = 37 A; TVJ = 150°C TVJ = 25°C 1.4 1.6 V V VT0 rT For power-loss calculations only TVJ = TVJM 1.01 7.1 V mW 1 70 K/W K/W K/W ● ● RthJC RthCK RthJA 0.25 trr IF = 1 A; -di/dt = 100 A/ms; VR = 30 V; TVJ = 25°C 35 50 ns IRM VR = 350 V; IF = 30 A; -diF/dt = 240 A/ms L £ 0.05 mH; TVJ = 100°C 10 11 A ① IFAVM rating includes reverse blocking losses at TVJM, VR = 0.8 VRRM, duty cycle d = 0.5 Data according to IEC 60747 and refer to a single diode unless otherwise stated. IXYS reserves the right to change limits, test conditions and dimensions © 2000 IXYS All rights reserved Rectifiers in switch mode power supplies (SMPS) Uninterruptible power supplies (UPS) Ultrasonic cleaners and welders ● ● High reliability circuit operation Low voltage peaks for reduced protection circuits Low noise switching Low losses Operating at lower temperature or space saving by reduced cooling 036 I2t ● International standard package JEDEC TO-247 AD Planar passivated chips Very short recovery time Extremely low switching losses Low IRM-values Soft recovery behavior Epoxy meets UL 94V-0 1-2 DSEK 60, 600 V Fig. 1 Forward current versus voltage drop. Fig. 2 Recovery charge versus -diF/dt. Fig. 3 Peak reverse current versus -diF/dt. Fig. 4 Dynamic parameters versus junction temperature. Fig. 5 Recovery time versus -diF/dt. Fig. 6 Peak forward voltage versus diF/dt. Dimensions Dim. M N Millimeter Min. Max. Inches Min. Max. A B 19.81 20.32 20.80 21.46 0.780 0.819 0.800 0.845 C D 15.75 16.26 3.55 3.65 0.610 0.140 0.640 0.144 E F 4.32 5.4 5.49 6.2 0.170 0.212 0.216 0.244 G H 1.65 - 2.13 4.5 0.065 - 0.084 0.177 J K 1.0 10.8 1.4 11.0 0.040 0.426 0.055 0.433 L M 4.7 0.4 5.3 0.8 0.185 0.016 0.209 0.031 N 2.2 2.54 0.087 0.102 Fig. 7 Transient thermal impedance junction to case. © 2000 IXYS All rights reserved 2-2