SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 • • • • • • • • • • Operates at 3-V to 3.6-V VCC Load Clock and Unload Clock Can Be Asynchronous or Coincident Low-Power Advanced CMOS Technology Full, Empty, and Half-Full Flags Programmable Almost-Full/Almost-Empty Flag Fast Access Times of 18 ns With a 50-pF Load and All Data Outputs Switching Simultaneously Data Rates From 0 to 40 MHz 3-State Outputs Pin Compatible With SN74ACT7804 Packaged in Shrink Small-Outline 300-mil Package (DL) Using 25-mil Center-to-Center Spacing description A FIFO memory is a storage device that allows data to be written into and read from its array at independent data rates. The SN74ALVC7804 is an 18-bit FIFO with high speed and fast access times. Data is processed at rates up to 40 MHz with access times of 18 ns in a bit-parallel format. The SN74ALVC7804 is designed for 3-V to 3.6-V VCC operation. DL PACKAGE (TOP VIEW) RESET D17 D16 D15 D14 D13 D12 D11 D10 VCC D9 D8 GND D7 D6 D5 D4 D3 D2 D1 D0 HF PEN AF/AE LDCK NC NC FULL 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 OE Q17 Q16 Q15 GND Q14 VCC Q13 Q12 Q11 Q10 Q9 GND Q8 Q7 Q6 Q5 VCC Q4 Q3 Q2 GND Q1 Q0 UNCK NC NC EMPTY Data is written into memory on a low-to-high 27 30 transition of the load clock (LDCK) and is read out 28 29 on a low-to-high transition of the unload clock (UNCK). The memory is full when the number of words clocked in exceeds the number of words clocked out by 512. When the memory is full, LDCK has no effect on the data residing in memory. When the memory is empty, UNCK has no effect. Status of the FIFO memory is monitored by the full (FULL), empty (EMPTY), half-full (HF), and almostfull/almost-empty (AF/AE) flags. The FULL output is low when the memory is full and high when the memory is not full. The EMPTY output is low when the memory is empty and high when it is not empty. The HF output is high whenever the FIFO contains 256 or more words and is low when it contains 255 or less words. The AF/AE status flag is a programmable flag. The first one or two low-to-high transitions of LDCK after reset are used to program the almost-empty offset value (X) and the almost-full offset value (Y), if program enable (PEN) is low. The AF/AE flag is high when the FIFO contains X or less words or (512 minus Y) or more words. The AF/AE flag is low when the FIFO contains between (X plus 1) and (511 minus Y) words. A low level on the reset (RESET) resets the internal stack pointers and sets FULL high, AF/AE high, HF low, and EMPTY low. The Q outputs are not reset to any specific logic level. The FIFO must be reset upon power up. The first word loaded into empty memory causes EMPTY to go high and the data to appear on the Q outputs. The data outputs are in the high-impedance state when the output-enable (OE) is high. Copyright 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 logic symbol† Φ FIFO 512 × 18 1 RESET LDCK UNCK OE D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 23 21 Full LDCK 32 56 PEN RESET 25 Half-Full UNCK Almost Full/Empty EN1 Empty 22 24 FULL HF AF/AE 29 EMPTY Program Enable 0 0 33 20 34 19 36 18 37 17 38 16 40 15 41 14 42 12 43 11 45 Data Data 1 9 46 8 47 7 48 6 49 5 51 4 53 3 54 2 55 17 17 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 Q17 SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 functional block diagram OE D0 – D17 RAM Read Pointer UNCK 512 × 18 Write Pointer LDCK Q0 – Q17 EMPTY Reset Logic RESET StatusFlag Logic PEN FULL HF AF/AE Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION AF/AE 24 O Almost full/almost empty flag. Depth offset values can be programmed for AF/AE, or the default value of 64 can be used for both the almost empty offset (X) and the almost full offset (Y). AF/AE is high when memory contains X or less words or (512 – Y) or more words. AF/AE is high after reset. D0 – D17 21 – 14, 12 – 11, 9–2 I 18-bit data input port EMPTY 29 O Empty flag. EMPTY is low when the FIFO is empty. A FIFO reset also causes EMPTY to go low. FULL 28 O Full flag. FULL is low when the FIFO is full. A FIFO reset causes FULL to go high. HF 22 O Half-full flag. HF is high when the FIFO memory contains 256 or more words. HF is low after reset. LDCK 25 I Load clock. Data is written to the FIFO on the rising edge of LDCK when FULL is high. OE 56 I Output enable. When OE is high, the data outputs are in the high-impedance state. PEN 23 I Program enable. After reset and before the first word is written to the FIFO, the binary value on D0 – D7 is latched as an AF/AE offset value when PEN is low and WRTCLK is high. Q0 – Q17 33 – 34, 36 – 38, 40 – 43, 45 – 49, 51, 53 – 55 O 18-bit data output port RESET 1 I Reset. A low level on RESET resets the FIFO and drives AF/AE and FULL high and HF and EMPTY low. UNCK 32 I Unload clock. Data is read from the FIFO on the rising edge of UNCK when EMPTY is high. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 0 ÉÉ ÉÉ ÉÉÉÉ ÉÉÉÉ ÉÉÉÉ ÉÉ ÉÉ ÉÉÉÉ ÉÉÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ LDCK D0–D17 W1 W2 W (X+1) A B Don’t Care C 1 OE W1 W2 W (Y+1) W (Y+2) D E F EMPTY AF/AE HF FULL Define the AF/AE Flag Using the Default Value of X and Y Figure 1. Write, Read, and Flag Timing Reference G ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ • DALLAS, TEXAS 75265 Q0–Q17 0 ÉÉ ÉÉÉÉ ÉÉ ÉÉ ÉÉÉÉ ÉÉ POST OFFICE BOX 655303 UNCK H I SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY 1 PEN SCAS432 – JANUARY 1995 4 RESET SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 DATA WORD NUMBERS FOR FLAG TRANSITIONS DEVICE SN74ALVC7804 TRANSITION WORD A B C D E F G H I W256 W(512 – Y) W512 W257 W258 W(512 – X) W(513 – X) W511 W512 offset values for AF/AE The AF/AE flag has two programmable limits: the almost-empty offset value (X) and the almost-full offset value (Y). They can be programmed after the FIFO is reset and before the first word is written to memory. The AF/AE flag is high when the FIFO contains X or less words or (512 minus Y) or more words. To program the offset values, PEN can be brought low after reset. On the following low-to-high transition of LDCK, the binary value on D0 – D7 is stored as the almost empty offset value (X) and the almost full offset value (Y). Holding PEN low for another low-to-high transition of LDCK reprograms Y to the binary value on D0 – D7 at the time of the second LDCK low-to-high transition. Writes to the FIFO memory are disabled while the offsets are programmed. A maximum value of 255 can be programmed for either X or Y (see Figure 2). To use the default values of X = Y = 64, PEN must be held high.Figure 1 RESET LDCK PEN D0 – D17 Don’t Care Don’t Care X and Y Y EMPTY Figure 2. Programming X and Y Separately POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V 50 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltage applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 V Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C * " " " † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings can be exceeded if the input and output clamp current ratings are observed. 2. This value is limited to 4.6 V maximum. recommended operating conditions ′ALVC7804-25 VCC = 3.3 V 0.3 V MIN MAX " VIH VIL High-level input voltage 2 Low-level input voltage ′ALVC7804-40 VCC = 3.3 V 0.3 V MIN MAX " 2 0.8 VI VO 0 0 VCC VCC 0 0 UNIT V 0.8 V VCC VCC V V IOH High-level output current,, g Q outputs, Flags VCC = 3 V –8 –8 mA IOL Low-level output current,, Q outputs, Flags VCC = 3 V 16 16 mA fclock Clock frequency 25 MHz tw Pulse duration 40 D0 – D17 high or low 8 12 LDCK high or low 8 12 UNCK high or low 8 12 PEN low 8 12 RESET low tsu th TA 6 Setup time Hold time 10 12 D0 – D17 before LDCK↑ 5 5 LDCK inactive before RESET high 6 6 PEN before LDCK↑ 8 8 D0 – D17 after LDCK↑ 0 0 PEN high after LDCK low 0 0 PEN low after LDCK↑ 3 3 LDCK inactive after RESET high 6 6 Operating free-air temperature 0 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 70 0 ns ns ns 70 °C SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) TEST CONDITIONS† PARAMETER TYP‡ MIN MAX UNIT VCC = MIN to MAX, VCC = 3 V, IOH = – 100 µA IOH = – 8 mA VCC = MIN to MAX, VCC = 3 V, IOL = 100 µA IOL = 8 mA VCC = 3 V, VCC = 3.6 V, IOL = 16 mA VI =VCC or GND 0.55 ±5 µA VCC = 3.6 V, VCC = 3.6 V, VO =VCC or GND VI = VCC or GND and IO = 0 ±10 µA 40 µA ∆ICC§ VCC = 3.6 V, Other inputs at VCC or GND One input at VCC – 0.6 V, 500 µA Ci VCC = 3.3 V, VCC = 3.3 V, VI = VCC or GND VO = VCC or GND VOH Flags Q outputs Flags, Flags, Q outputs VOL Flags Q outputs II IOZ ICC Co VCC – 0.2 2.4 V 0.2 0.4 V 3 pF 6 pF † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 3.3 V, TA = 25°C. § This is the supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 5) PARAMETER FROM (INPUT) TO (OUTPUT) ′ALVC7804-25 VCC = 3.3 V 0.3 V MIN MAX " ′ALVC7804-40 VCC = 3.3 V 0.3 V MIN MAX " fmax tpd LDCK or UNCK 40 LDCK↑ 9 22 9 24 tpd tPLH UNCK↑ 6 18 6 20 6 17 6 19 tPHL tPHL UNCK↑ 6 17 6 19 RESET low 4 18 4 20 LDCK↑ 6 17 6 19 6 17 6 19 tPHL tPLH Any Q LDCK↑ EMPTY UNCK↑ FULL 25 MHz tPLH tpd RESET low 4 20 4 22 LDCK↑ 7 20 7 22 tpd tPLH UNCK↑ 7 20 7 22 RESET low 2 12 2 14 LDCK↑ 5 20 5 22 7 20 7 22 3 14 3 16 2 10 2 11 2 11 2 12 tPLH tPHL tPHL ten tdis AF/AE UNCK↑ HF RESET low Any Q OE UNIT ns ns ns ns ns ns operating characteristics, VCC = 3.3 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per FIFO channel Outputs enabled POST OFFICE BOX 655303 CL = 50 pF, • DALLAS, TEXAS 75265 f = 5 MHz TYP UNIT 53 pF 7 SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 APPLICATION INFORMATION ′ALVC78xx LDCK LDCK UNCK UNCK EMPTY FULL EMPTY FULL OE D18 – D35 D0 – D17 OE Q18 – Q35 Q0 – Q17 ′ALVC78xx LDCK FULL UNCK EMPTY OE D0 – D17 D0 – D17 Q0 – Q17 Figure 3. Word-Width Expansion: 512 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Q0 – Q17 36 Bit SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs CLOCK FREQUENCY 140 fdata = 1/2 fclock TA = 75°C CL = 0 pF I CC(f) – Supply Current – mA 120 VCC = 3.6 V 100 VCC = 3.3 V 80 60 VCC = 3 V 40 20 0 0 10 20 30 40 50 60 70 80 90 fclock – Clock Frequency – MHz Figure 4 calculating power dissipation With ICC(f) taken from Figure 4, the dynamic power (Pd), based on all data outputs changing states on each read, can be calculated by using: Pd = VCC × [ICC(f) + (N × ∆ICC × dc)] + ∑(CL × VCC2 × fo) A more accurate total power (PT) can be calculated if quiescent power (Pq) is also taken into consideration. Quiescent power (Pq) can be calculated using: Pq = VCC × [ICCI + (N × ∆ICC × dc)] Total power will be: PT = Pd + Pq The above equations provide worst-case power calculations. Where: N ∆ICC dc CL fo ICCI = = = = = = number of inputs driven by TTL levels increase in power supply current for each input at a TTL high level duty cycle of inputs at a TTL high level of 3.4 V output capacitance load switching frequency of an output idle current, supply current when FIFO is idle ≈ pF × fclock = 0.2 × fclock (current is due to free-running clocks) pF = power factor (the slope of idle ICC versus frequency) ICC(f) = active current, supply current when FIFO is transferring data POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 SN74ALVC7804 512 × 18 FIRST-IN, FIRST-OUT MEMORY SCAS432 – JANUARY 1995 PARAMETER MEASUREMENT INFORMATION 6V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω LOAD CIRCUIT FOR OUTPUTS tw 3V 3V Timing Input Input 1.5 V tsu 0V VOLTAGE WAVEFORMS PULSE DURATION th 1.5 V 1.5 V 1.5 V 0V tPLH tPHL Output Waveform 2 S1 at GND (see Note B) VOH 1.5 V tPLZ 3V Output Waveform 1 S1 at 6 V (see Note B) 1.5 V 1.5 V VOL 1.5 V 0V tPZL 3V 1.5 V 3V Output Control (low-level enabling) 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES Output 1.5 V 3V Data Input Input 1.5 V 0V 1.5 V VOL tPHZ tPZH VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOL + 0.3 V VOH 1.5 V VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 Ω, tr 2.5 ns, tf 2.5 ns. v v 3-STATE OUTPUTS (ANY Q) PARAMETER R1, R2 CL† ten tPZH tPZL 500 Ω 50 pF tdi dis tPHZ tPLZ 500 Ω 50 pF tpd tPLH / tPHL 500 Ω 50 pF S1 GND 6V GND 6V Open † Includes probe and test-fixture capacitance Figure 5. Standard CMOS Outputs (FULL, EMPTY, HF, AF/AE) 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 v PACKAGE OPTION ADDENDUM www.ti.com 22-Jan-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74ALVC7804-25DL ACTIVE SSOP DL 56 SN74ALVC7804-25DLR ACTIVE SSOP DL 56 SN74ALVC7804-40DL ACTIVE SSOP DL 56 SN74ALVC7804-40DLR ACTIVE SSOP DL 56 20 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 20 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001 DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0.025 (0,635) 0.0135 (0,343) 0.008 (0,203) 48 0.005 (0,13) M 25 0.010 (0,25) 0.005 (0,13) 0.299 (7,59) 0.291 (7,39) 0.420 (10,67) 0.395 (10,03) Gage Plane 0.010 (0,25) 1 0°–ā8° 24 0.040 (1,02) A 0.020 (0,51) Seating Plane 0.110 (2,79) MAX 0.004 (0,10) 0.008 (0,20) MIN PINS ** 28 48 56 A MAX 0.380 (9,65) 0.630 (16,00) 0.730 (18,54) A MIN 0.370 (9,40) 0.620 (15,75) 0.720 (18,29) DIM 4040048 / E 12/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MO-118 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony Mailing Address: Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated