VISHAY 293D107X0010D2T

293D
Vishay Sprague
Solid Tantalum Chip Capacitors
TANTAMOUNT®, Commercial, Surface Mount
FEATURES
• Molded case available in six case codes.
• Compatible with "High Volume" automatic pick and place
equipment.
• Optical character recognition qualified.
• Meets IEC Specification QC300801/US0001 and
EIA 535BAAC.
PERFORMANCE/ELECTRICAL CHARACTERISTICS
Operating Temperature: - 55°C to + 85°C. (to + 125°C
with voltage derating.)
Capacitance Range: 0.10µF to 680µF.
Capacitance Tolerance: ± 20%, ± 10% standard. (20% only on P)
Compliant Terminations
100% Surge Current Tested (D & E Case Codes).
Voltage Rating: 4 WVDC to 50 WVDC.
OTHER SPECIFCATIONS
CECC
IECQ
30801-005
793DX
PQC32/GB003
793DX
30801-009
CTC3
300801/FR001
CTC3
30801-011
30801-801
CTC4
793DE
ORDERING INFORMATION
293D
TYPE
107
CAPACITANCE
X9
CAPACITANCE
TOLERANCE
010
DC VOLTAGE RATING
@ + 85°C
This is expressed in X0 = ± 20% This is expressed in volts.
picofarads. The
To complete the threeX9 = ± 10% digit block, zeros precede
first two digits are
X5 = ± 5%
the significant
the voltage rating. A
figures. The third is (Special Order) decimal point is indicated
the number of zeros
by an "R"
to follow.
(6R3 = 6.3 volts).
Note: Preferred Tolerance and reel sizes are in bold.
793DX
793DE
CTC3
CTC4
D
CASE CODE
2
TERMINATION
W
REEL SIZE AND
PACKAGING
See Ratings
and Case
Code Tables.
2 = Solderable
coating.
Standard.
T = 7" [178mm] reel,*
W = 13" [330mm] reel*
*cathode nearest
sprocket hole.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage
substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
L
W
H
TH Min.
P
TW
CASE
CODE
A
EIA
SIZE
3216
B
3528
C
6032
D
7343
E
7343H
P
2012
Document Number 40002
Revision 27-Oct-04
L
0.126 ± 0.008
[3.2 ± 0.20]
0.138 ± 0.008
[3.5 ± 0.20]
0.236 ± 0.012
[6.0 ± 0.30]
0.287 ± 0.012
[7.3 ± 0.30]
0.287 ± 0.012
[7.3 ± 0.30]
0.079 ± 0.20
[2.0 ± 0.008]
W
0.063 ± 0.008
[1.6 ± 0.20]
0.110 ± 0.008
[2.8 ± 0.20]
0.126 ± 0.012
[3.2 ± 0.30]
0.170 ± 0.012
[4.3 ± 0.30]
0.170 ± 0.012
[4.3 ± 0.30
0.049 ± 0.008
[1.25 ± 0.2]
H
0.063 ± 0.008
[1.6 ± 0.20]
0.075 ± 0.008
[1.9 ± 0.20]
0.098 ± 0.012
[2.5 ± 0.30]
0.110 ± 0.012
[2.8 ± 0.30]
0.158 ± 0.012
[4.0 ± 0.30]
0.047 Max.
[1.2 Max.]
P
0.031 ± 0.012
[0.80 ± 0.30]
0.031 ± 0.012
[0.80 ± 0.30]
0.051 ± 0.012
[1.3 ± 0.30]
0.051 ± 0.012
[1.3 ± 0.30]
0.051 ± 0.012
[1.3 ± 0.30]
0.020 ± 0.008
[0.52 ± 0.20]
For technical questions, contact [email protected]
TW
0.047 ± 0.004
[1.2 ± 0.10]
0.087 ± 0.004
[2.2 ± 0.10]
0.087 ± 0.004
[2.2 ± 0.10]
0.095 ± 0.004
[2.4 ± 0.10]
0.095 ± 0.004
[2.4 ± 0.10]
0.047 ± 0.004
[1.2 ± 0.10]
TH (Min.)
0.028
[0.70]
0.028
[0.70]
0.039
[1.0]
0.039
[1.0]
0.039
[1.0]
0.012
[0.3]
www.vishay.com
15
293D
Vishay Sprague
RATINGS AND CASE CODES
6.3 V
4V
µF
0.10
0.15
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
Std.
Ext.
Std.
10 V
Ext.
Std.
Ext.
P
A
A
A
A/B/P
B/P
B/C/P
C
C
D
D
D
E
A
A
A/B
A*/B
B/C
B/C
B/C
C/D
D/E
D/E
E
A
A/P
A/B/P
A/B/P
B/C/P
B/C
C
C
D
D
D
E
A
A
A/B
A/B
B/C
B/C
B/C
C/D
D/E
D/E
E
A
A/P
A/P
A/B/P
B
B/C
C
C
D
D
D
A
A
A/B
A/B
B/C
B/C
B*/C
C/D
D/E
D/E
E
16 V
Std.
A/P
A
A/B
A/B
B
B/C
C
C
D
D
D
Ext.
A
A
A/B
B
B/C
B/C
C
D
D/E
D*/E
25 V
20 V
Std.
A
A
A
B
B
B/C
C
C
D
D
D
Ext.
Std.
A
A
B
B
B
C
C
C
D
D
A
A
A
B
B
B/C
C
C
D/E
D/E
E
Ext.
35 V
Std.
A
A
A
B
B
B
C
C
D
D/E
E*
A
A
A
A
B
B
B
C
C
C
D
D
D
Ext.
A
A
A
B
B
B
C
C
C
D/E
D/E
E*
50 V
Std.
Ext.
A
B
B
B
B/C
C
C
A
A
A
A
B
B
C
C/D
C
D
D
D
D/E
D/E
*Preliminary values, contact factory for availability.
CONSTRUCTION AND MARKING
CONSTRUCTION
MARKING
Capacitance Code,
pF
Vishay
Sprague
Logo
Cathode
Termination ( - )
Capacitance
V 104
Polarity
Band
B, C, D, E
22
10
XX
2
Voltage Code
Polarity
Stripe (+)
“A” Case
Polarity Band
Date Code
Epoxy Case
X
Tantalum
Capacitor
Element
Voltage
Anode Weld
Positive
Termination
X
Voltage
Capacitance
“P” Case
Polarity Band
Vishay
Sprague
Logo
Volts
Code
4
6.3
10
16
20
25
35
50
G
J
A
C
D
E
V
T
Marking:
Capacitor marking will include an anode (+) polarity band, capacitance in
microfarads and the voltage rating of + 85°C. 'A' Case capacitors use a
letter code for the voltage and EIA capacitance code.
The Sprague® trademark may be included if space permits.
Units rated at 6.3 V shall be marked 6 V.
A manufacturing date code is marked on all case codes.
Call the factory for further explanation.
www.vishay.com
16
For technical questions, contact [email protected]
Document Number 40002
Revision 27-Oct-04
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE
(µF)
3.3
4.7
6.8
10
10
10
15
15
15
22
22
22
22
33
33
33
47
47
68
68
68
100
100
100
150
150
150
220
220
220
330
330
470
470
680
2.2
3.3
3.3
4.7
4.7
6.8
6.8
6.8
10
10
10
15
15
15
22
22
22
33
33
47
47
47
68
68
68
100
100
100
150
150
150
220
220
330
330
470
Max. ESR
Max. DC
Max. DF
@ + 25°C
Leakage
@ + 25°C
100kHz
@ + 25°C
120 Hz
PART NUMBER
(Ohms)
(µA)
(%)
4 WVDC @ + 85°C, SURGE = 5.2 V . . . 2.7 WVDC @ + 125°C, SURGE = 3.4 V
0.5
A
6
7.6
293D335X_004A2_E3
0.5
A
6
6.3
293D475X_004A2_E3
0.5
A
6
5.5
293D685X_004A2_E3
0.5
A
6
5.1
293D106X_004A2_E3
0.5
B
6
3.5
293D106X_004B2_E3
0.5
P
6
N/A
293D106X_004P2_E3
0.6
A
6
3.4
293D156X_004A2_E3
0.6
B
6
2.9
293D156X_004B2_E3
0.6
P
6
N/A
293D156X_004P2_E3
0.9
A
6
2.9
293D226X_004A2_E3
0.9
B
6
2.5
293D226X_004B2_E3
0.9
C
6
1.8
293D226X_004C2_E3
0.9
P
6
N/A
293D226X0004P2_E3
1.3
A
6
2.9
293D336X_004A2_E3
1.3
B
6
2.0
293D336X_004B2_E3
1.3
C
6
1.8
293D336X_004C2_E3
1.9
B
6
1.9
293D476X_004B2_E3
1.9
C
6
1.8
293D476X_004C2_E3
2.7
B
6
1.9
293D686X_004B2_E3
2.7
C
6
1.4
293D686X_004C2_E3
2.7
D
6
0.8
293D686X_004D2_E3
4.0
B
8
1.8
293D107X_004B2_E3
4.0
C
6
0.8
293D107X_004C2_E3
4.0
D
6
0.7
293D107X_004D2_E3
6.0
B
14
1.6
293D157X_004B2_E3
6.0
C
12
0.7
293D157X_004C2_E3
6.0
D
8
0.6
293D157X_004D2_E3
8.8
C
8
0.7
293D227X_004C2_E3
8.8
D
8
0.6
293D227X_004D2_E3
8.8
E
8
0.5
293D227X_004E2_E3
13.2
D
8
0.6
293D337X_004D2_E3
13.2
E
8
0.5
293D337X_004E2_E3
18.8
D
10
0.6
293D477X_004D2_E3
18.8
E
10
0.5
293D477X_004E2_E3
27.2
E
12
0.5
293D687X_004E2_E3
6.3 WVDC @ + 85°C, SURGE = 8 V . . . 4 WVDC @ + 125°C, SURGE = 5 V
7.6
6
293D225X_6R3A2_E3
0.5
A
6.3
6
293D335X_6R3A2_E3
0.5
A
N/A
6
293D335X_6R3P2_E3
0.5
P
5.5
293D475X_6R3A2_E3
6
0.5
A
N/A
6
293D475X_6R3P2_E3
0.5
P
5.0
293D685X_6R3A2_E3
6
0.5
A
3.4
293D685X_6R3B2_E3
6
0.5
B
N/A
293D685X_6R3P2_E3
6
0.5
P
3.4
293D106X_6R3A2_E3
6
0.6
A
2.9
6
293D106X_6R3B2_E3
0.6
B
N/A
293D106X_6R3P2_E3
6
0.6
P
2.9
6
293D156X_6R3A2_E3
0.9
A
2.5
6
293D156X_6R3B2_E3
0.9
B
1.8
293D156X_6R3C2_E3
6
0.9
C
2.9
6
293D226X_6R3A2_E3
1.3
A
2.0
6
293D226X_6R3B2_E3
1.3
B
1.8
293D226X_6R3C2_E3
6
1.3
C
1.9
6
293D336X_6R3B2_E3
2.0
B
1.5
6
293D336X_6R3C2_E3
2.0
C
1.9
293D476X_6R3B2_E3
6
2.8
B
1.4
6
293D476X_6R3C2_E3
2.8
C
0.8
6
293D476X_6R3D2_E3
2.8
D
1.8
293D686X_6R3B2_E3
6
4.1
B
0.8
6
293D686X_6R3C2_E3
4.1
C
0.7
6
293D686X_6R3D2_E3
4.1
D
1.7
293D107X_6R3B2_E3
12
6.0
B
0.8
6
293D107X_6R3C2_E3
6.0
C
0.7
6
293D107X_6R3D2_E3
6.0
D
0.7
293D157X_6R3C2_E3
8
9.0
C
0.6
8
293D157X_6R3D2_E3
9.0
D
0.5
8
293D157X_6R3E2_E3
9.0
E
0.6
293D227X_6R3D2_E3
8
13.2
D
0.5
8
293D227X_6R3E2_E3
13.2
E
0.6
8
293D337X_6R3D2_E3
19.8
D
0.5
293D337X_6R3E2_E3
8
19.8
E
0.5
10
293D477X_6R3E2_E3
28.2
E
CASE
CODE
Max. RIPPLE
100kHz
Irms
(Amps)
0.10
0.11
0.12
0.12
0.16
0.085
0.15
0.17
0.085
0.16
0.18
0.25
0.085
0.16
0.21
0.25
0.21
0.25
0.21
0.28
0.43
0.22
0.37
0.46
0.23
0.40
0.50
0.40
0.50
0.57
0.50
0.57
0.50
0.57
0.57
0.10
0.11
0.085
0.12
0.085
0.12
0.16
0.085
0.15
0.17
0.085
0.16
0.18
0.25
0.16
0.21
0.25
0.21
0.27
0.21
0.28
0.43
0.22
0.37
0.46
0.22
0.37
0.46
0.40
0.50
0.57
0.50
0.57
0.50
0.57
0.57
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
Document Number 40002
Revision 27-Oct-04
For technical questions, contact [email protected]
www.vishay.com
17
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE
(µF)
1.0
1.5
2.2
2.2
3.3
3.3
4.7
4.7
4.7
6.8
6.8
10
10
10
15
15
15
22
22
22
33
33
33
47
47
47
68
68
100
100
150
150
220
220
330
1.0
1.0
1.5
2.2
2.2
3.3
3.3
4.7
4.7
6.8
6.8
6.8
10
10
10
15
15
22
22
22
33
33
33
47
47
68
100
100
150
Max. ESR
Max. DC
Max. DF
@ + 25°C
Leakage
@ + 25°C
CASE
100kHz
@ + 25°C
120 Hz
CODE
PART NUMBER
(Ohms)
(µA)
(%)
10 WVDC @ + 85°C, SURGE = 13 V . . . 7 WVDC @ + 125°C, SURGE = 8 V
0.5
6
P
293D105X_010P2_E3
N/A
0.5
6
293D155X_010A2_E3
A
8.0
0.5
6
293D225X_010A2_E3
A
6.3
0.5
6
P
293D225X_010P2_E3
N/A
0.5
6
293D335X_010A2_E3
A
5.5
0.5
6
293D335X_010P2_E3
P
N/A
0.5
6
293D475X_010A2_E3
A
5.0
0.5
6
293D475X_010B2_E3
B
3.4
0.5
6
293D475X_010P2_E3
P
N/A
0.7
6
A
293D685X_010A2_E3
4.2
0.7
6
293D685X_010B2_E3
B
2.9
1.0
6
293D106X_010A2_E3
A
3.4
1.0
6
B
293D106X_010B2_E3
2.5
1.0
6
293D106X_010C2_E3
C
1.8
1.5
6
293D156X_010A2_E3
A
2.9
1.5
6
B
293D156X_010B2_E3
2.0
1.5
6
293D156X_010C2_E3
C
1.8
2.2
8
293D226X_010A2_E3
A
2.5
2.2
6
293D226X_010B2_E3
B
1.9
2.2
6
293D226X_010C2_E3
C
1.5
3.3
6
293D336X_010B2_E3
B
1.9
3.3
6
293D336X_010C2_E3
C
1.4
3.3
6
293D336X_010D2_E3
D
0.8
4.7
6
293D476X_010B2_E3
B
1.8
4.7
6
293D476X_010C2_E3
C
1.1
4.7
6
293D476X_010D2_E3
D
0.7
6.8
6
293D686X_010C2_E3
C
1.0
6.8
6
293D686X_010D2_E3
D
0.7
10
8
293D107X_010C2_E3
C
0.9
10
8
293D107X_010D2_E3
D
0.6
15
8
293D157X_010D2_E3
D
0.6
15
8
293D157X_010E2_E3
E
0.5
22
8
293D227X_010D2_E3
D
0.6
22
8
293D227X_010E2_E3
E
0.5
33
10
293D337X_010E2_E3
0.5
E
16 WVDC @ + 85°C, SURGE = 20 V . . . 10 WVDC @ + 125°C, SURGE = 12 V
A
P
A
A
B
A
B
A
B
A
B
C
A
B
C
B
C
B
C
D
B
C
D
C
D
D
D
E
E
293D105X_016A2_E3
293D105X_016P2_E3
293D155X_016A2_E3
293D225X_016A2_E3
293D225X_016B2_E3
293D335X_016A2_E3
293D335X_016B2_E3
293D475X_016A2_E3
293D475X_016B2_E3
293D685X_016A2_E3
293D685X_016B2_E3
293D685X_016C2_E3
293D106X_016A2_E3
293D106X_016B2_E3
293D106X_016C2_E3
293D156X_016B2_E3
293D156X_016C2_E3
293D226X0016B2_E3
293D226X_016C2_E3
293D226X_016D2_E3
293D336X0016B2_E3
293D336X_016C2_E3
293D336X_016D2_E3
293D476X_016C2_E3
293D476X_016D2_E3
293D686X_016D2_E3
293D107X_016D2_E3
293D107X_016E2_E3
293D157X_016E2_E3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
1.1
1.1
1.1
1.6
1.6
1.6
2.4
2.4
3.5
3.5
3.5
5.3
5.3
5.3
7.5
7.5
10.9
16
16
24
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
9.3
N/A
6.7
5.9
4.6
5.0
3.5
5.0
2.9
4.2
2.5
1.9
3.0
2.0
1.8
2.0
1.5
1.9
1.4
0.8
1.8
1.1
0.7
1.0
0.7
0.6
0.6
0.6
0.5
Max. RIPPLE
100kHz
Irms
(Amps)
0.07
0.10
0.11
0.07
0.12
0.07
0.12
0.16
0.07
0.13
0.17
0.15
0.18
0.25
0.16
0.21
0.25
0.17
0.21
0.27
0.21
0.28
0.43
0.22
0.32
0.46
0.33
0.46
0.35
0.50
0.50
0.57
0.50
0.57
0.57
0.09
0.07
0.11
0.11
0.14
0.12
0.16
0.12
0.17
0.13
0.18
0.24
0.16
0.21
0.25
0.21
0.27
0.21
0.28
0.43
0.22
0.32
0.46
0.33
0.46
0.50
0.50
0.52
0.57
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
www.vishay.com
18
For technical questions, contact [email protected]
Document Number 40002
Revision 27-Oct-04
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE
(µF)
CASE
CODE
0.68
1.0
1.5
2.2
2.2
3.3
3.3
4.7
4.7
4.7
6.8
6.8
10
10
15
15
15
22
22
33
33
47
47
68
68
100
A
A
A
A
B
A
B
A
B
C
B
C
B
C
B
C
D
C
D
C
D
D
E
D
E
E
PART NUMBER
Max. DC
Leakage
@ + 25°C
(µA)
Max. DF
@ + 25°C
120 Hz
(%)
Max. ESR
@ + 25°C
100kHz
(Ohms)
Max. RIPPLE
100kHz
Irms
(Amps)
20 WVDC @ + 85°C, SURGE = 26 V . . . 13 WVDC @ + 125°C, SURGE = 16 V
293D684X_020A2_E3
293D105X_020A2_E3
293D155X_020A2_E3
293D225X_020A2_E3
293D225X_020B2_E3
293D335X_020A2_E3
293D335X_020B2_E3
293D475X_020A2_E3
293D475X_020B2_E3
293D475X_020C2_E3
293D685X_020B2_E3
293D685X_020C2_E3
293D106X_020B2_E3
293D106X_020C2_E3
293D156X_020B2_E3
293D156X_020C2_E3
293D156X_020D2_E3
293D226X_020C2_E3
293D226X_020D2_E3
293D336X_020C2_E3
293D336X_020D2_E3
293D476X_020D2_E3
293D476X_020E2_E3
293D686X_020D2_E3
293D686X_020E2_E3
293D107X_020E2_E3
0.5
0.5
0.5
0.5
0.5
0.7
0.7
0.9
0.9
0.9
1.4
1.4
2.0
2.0
3.0
3.0
3.0
4.4
4.4
6.6
6.6
9.4
9.4
13.6
13.6
20.0
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
8
10
8.4
6.3
5.9
3.5
5.9
3.0
5.0
2.9
2.3
2.5
1.9
2.5
1.7
2.3
1.5
0.9
1.1
0.7
1.0
0.7
0.7
0.6
0.7
0.6
0.5
0.09
0.09
0.11
0.11
0.16
0.11
0.17
0.12
0.17
0.22
0.18
0.24
0.18
0.25
0.19
0.27
0.41
0.32
0.46
0.33
0.46
0.46
0.52
0.46
0.52
0.57
25 WVDC @ + 85°C, SURGE = 32 V . . . 17 WVDC @ + 125°C, SURGE = 20 V
0.47
0.68
1.0
1.0
1.5
1.5
2.2
2.2
3.3
3.3
4.7
4.7
6.8
6.8
10
10
15
15
22
33
33
A
A
A
B
A
B
A
B
B
C
B
C
B
C
C
D
C
D
D
D
E
293D474X_025A2_E3
293D684X_025A2_E3
293D105X_025A2_E3
293D105X_025B2_E3
293D155X_025A2_E3
293D155X_025B2_E3
293D225X_025A2_E3
293D225X_025B2_E3
293D335X_025B2_E3
293D335X_025C2_E3
293D475X_025B2_E3
293D475X_025C2_E3
293D685X_025B2_E3
293D685X_025C2_E3
293D106X_025C2_E3
293D106X_025D2_E3
293D156X_025C2_E3
293D156X_025D2_E3
293D226X_025D2_E3
293D336X_025D2_E3
293D336X_025E2_E3
0.5
0.5
0.5
0.5
0.5
0.5
0.6
0.6
0.8
0.8
1.2
1.2
1.7
1.7
2.5
2.5
3.8
3.8
5.5
8.3
8.3
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
12
8.4
7.6
5.0
6.7
4.6
6.3
3.8
3.1
2.3
2.8
2.0
2.4
1.7
1.5
1.0
1.2
0.8
0.7
0.7
0.6
0.08
0.09
0.10
0.13
0.11
0.14
0.11
0.15
0.17
0.22
0.17
0.24
0.19
0.25
0.27
0.39
0.30
0.43
0.46
0.46
0.52
**Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
Document Number 40002
Revision 27-Oct-04
For technical questions, contact [email protected]
www.vishay.com
19
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE
(µF)
CASE
CODE
PART NUMBER
Max. DC
Leakage
@ + 25°C
(µA)
Max. DF
@ + 25°C
120 Hz
(%)
Max. ESR
@ + 25°C
100kHz
(Ohms)
Max. RIPPLE
100kHz
Irms
(Amps)
35 WVDC @ + 85°C, SURGE = 46 V . . . 23 WVDC @ + 125°C, SURGE = 28 V
0.10
0.15
0.22
0.33
0.47
0.47
0.68
0.68
1.0
1.0
1.5
1.5
2.2
2.2
3.3
3.3
4.7
4.7
6.8
6.8
10
10
15
15
22
22
A
A
A
A
A
B
A
B
A
B
B
C
B
C
B
C
C
D
C
D
C
D
D
E
D
E
0.10
0.15
0.15
0.22
0.22
0.33
0.33
0.47
0.47
0.47
0.68
0.68
1.0
1.0
1.5
2.2
2.2
3.3
3.3
4.7
6.8
6.8
10
10
A
A
B
A
B
A
B
A
B
C
B
C
B
C
C
C
D
C
D
D
D
E
D
E
293D104X_035A2_E3
293D154X_035A2_E3
293D224X_035A2_E3
293D334X_035A2_E3
293D474X_035A2_E3
293D474X_035B2_E3
293D684X_035A2_E3
293D684X_035B2_E3
293D105X_035A2_E3
293D105X_035B2_E3
293D155X_035B2_E3
293D155X_035C2_E3
293D225X_035B2_E3
293D225X_035C2_E3
293D335X_035B2_E3
293D335X_035C2_E3
293D475X_035C2_E3
293D475X_035D2_E3
293D685X_035C2_E3
293D685X_035D2_E3
293D106X_035D2_E3
293D106X_035D2_E3
293D156X_035D2_E3
293D156X_035E2_E3
293D226X_035D2_E3
293D226X_035E2_E3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
0.8
1.2
1.2
1.6
1.6
2.4
2.4
3.5
3.5
5.3
5.3
7.7
7.7
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
20
18
15
13
10
8
7.6
6.5
7.5
5.0
4.2
3.8
3.8
2.9
3.5
2.1
1.9
1.3
1.8
1.1
0.7
0.8
0.7
0.7
0.6
0.6
0.06
0.07
0.07
0.08
0.09
0.10
0.10
0.11
0.10
0.13
0.14
0.17
0.15
0.20
0.16
0.23
0.24
0.34
0.25
0.37
0.46
0.43
0.46
0.49
0.52
0.52
50 WVDC @ + 85°C, SURGE = 65 V . . . 33 WVDC @ + 125°C, SURGE = 40 V
293D104X_050A2_E3
293D154X_050A2_E3
293D154X_050B2_E3
293D224X_050A2_E3
293D224X_050B2_E3
293D334X_050A2_E3
293D334X_050B2_E3
293D474X_050A2_E3
293D474X_050B2_E3
293D474X_050C2_E3
293D684X_050B2_E3
293D684X_050C2_E3
293D105X_050B2_E3
293D105X_050C2_E3
293D155X_050C2_E3
293D225X_050C2_E3
293D225X_050D2_E3
293D335X_050C2_E3
293D335X_050D2_E3
293D475X_050D2_E3
293D685X_050D2_E3
293D685X_050E2_E3
293D106X_050D2_E3
293D106X_050E2_E3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.8
1.1
1.1
1.7
1.7
2.4
3.4
3.4
5.0
5.0
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
6
6
19
17
14
15
12
14
10
12
8.4
6.7
7.6
5.9
6.7
4.6
3.4
2.9
2.1
2.5
1.7
1.2
0.9
0.9
0.8
0.8
0.06
0.07
0.08
0.07
0.08
0.07
0.09
0.08
0.10
0.13
0.11
0.14
0.11
0.16
0.18
0.20
0.27
0.21
0.30
0.37
0.41
0.43
0.43
0.45
**Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
www.vishay.com
20
For technical questions, contact [email protected]
Document Number 40002
Revision 27-Oct-04
293D
Vishay Sprague
TYPICAL CURVES @ + 25°C, IMPEDANCE AND ESR
100
VS
FREQUENCY
100
IMPEDANCE
ESR
IMPEDANCE
ESR
10
OHMS
OHMS
10
4.7µF, 10VDC-B CASE
10µF, 16VDC-C CASE
1
1
47µF, 10VDC-D CASE
0.1
0.1
1K
10K
100K
1M
10M
100M
1K
10K
FREQUENCY IN HERTZ
100K
1M
10M
100M
FREQUENCY IN HERTZ
100
100
IMPEDANCE
ESR
IMPEDANCE
ESR
10
OHMS
OHMS
10
1µF, 35VDC-B CASE
6.8µF, 20VDC-C CASE
1
1
6.8µF, 35VDC-D CASE
22µF, 20VDC-D CASE
0.1
0.1
1K
10K
100K
1M
10M
100M
1K
10K
FREQUENCY IN HERTZ
Document Number 40002
Revision 27-Oct-04
For technical questions, contact [email protected]
100K
1M
10M
100M
FREQUENCY IN HERTZ
www.vishay.com
21
293D
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1.
Operating Temperature: Capacitors are designed to
operate over the temperature range - 55°C to + 85°C.
1.1
Capacitors may be operated to + 125°C with
voltage derating to two-thirds the + 85°C rating.
+ 85°C Rating
2.
5.
- 55°C
- 10%
+ 125°C Rating
Working
Voltage
(V)
Surge
Voltage
(V)
Working
Voltage
(V)
Surge
Voltage
(V)
4
6.3
10
16
20
25
35
50
5.2
8
13
20
26
32
46
65
2.7
4
7
10
13
17
23
33
3.4
5
8
12
16
20
28
40
6.1
Measurements shall be made by the bridge method
at, or referred to, a frequency of 120 Hz and a
temperature of + 25°C.
7.
Leakage Current: Capacitors shall be stabilized at
the rated temperature for 30 minutes. Rated voltage
shall be applied to capacitors for 5 minutes using a
steady source of power (such as a regulated power
supply) with 1000 ohm resistor connected in series
with the capacitor under test to limit the charging
current. Leakage current shall then be measured.
rated temperature.
Surge Voltage: The surge DC rating is the maximum
under any conditions, including transients and peak
ripple at the highest line voltage.
3.1
Surge Voltage Test: Capacitors shall withstand
+ 125°C
+ 12%
Dissipation Factor: The dissipation factor,
determined from the expression 2πfRC, shall not
exceed values listed in the Standard Ratings Table.
DC Working Voltage: The DC working voltage is the
voltage to which the capacitors may be subjected
+ 85°C
+ 10%
6.
maximum operating voltage for continuous duty at the
3.
Capacitance Change With Temperature: The
capacitance change with temperature shall not exceed
the following percentage of the capacitance measured
at + 25°C:
Note that the leakage current varies with temperature and
applied voltage. See graph below for the appropriate adjustment
factor.
TYPICAL LEAKAGE CURRENT FACTOR RANGE
100
the surge voltage applied in series with a 33 ohm
± 5% resistor at the rate of one-half minute on,
one-half minute off, at + 85°C, for 1000 successive
+ 125°C
test cycles.
+ 85°C
10
3.2
Following the surge voltage test, the dissipation
+ 55°C
factor and the leakage current shall meet the initial
requirements; the capacitance shall not have changed
4.
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance
limits of the normal rating.
4.1
Capacitance measurements shall be made by means
+ 25°C
Leakage Current Factor
more than ± 10%.
1.0
0°C
0.1
- 55°C
of polarized capacitance bridge. The polarizing
voltage shall be of such magnitude that there shall be
no reversal of polarity due to the AC component. The
0.01
maximum voltage applied to capacitors during
measurement shall be 2 volts rms at 120 Hz at +25°C.
If the AC voltage applied is less than one-half volt rms,
no DC bias is required. Accuracy of the bridge shall
0.001
0
10
20
be within ± 2%.
www.vishay.com
22
30
40
50
60
70
80
90
100
Percent of Rated Voltage
For technical questions, contact [email protected]
Document Number 40002
Revision 27-Oct-04
293D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
7.1
At + 25°C, the leakage current shall not exceed
the value listed in the Standard Ratings Table.
0.06" [1.52] ± 10% maximum total excursion or 20 g
peak whichever is less.
7.2
At + 85°C, the leakage current shall not exceed 10
times the value listed in the Standard Ratings Table.
10.3.1 Vibration frequency shall be varied logarithmically
from 50 Hz to 2000 Hz and return to 50 Hz during
a cycle period of 20 minutes.
7.3
At + 125°C, the leakage current shall not exceed
12 times the value listed in the Standard Ratings
Table.
10.3.2 The vibration shall be applied for 4 hours in each of 2
directions, parallel and perpendicular to the major axis
of the capacitors.
8.
ESR
8.1
ESR (Equivalent Series Resistance) shall not
exceed the values listed in the Ratings Table.
Measurement shall be made by the bridge method
at a frequency of 100kHz and a temperature of +25°C.
10.3.3 Rated DC voltage shall be applied during the vibration
cycling.
9.
9.1
Life Test: Capacitors shall withstand rated DC
voltage applied at + 85°C or two-thirds rated voltage
applied at + 125°C for 2000 hours.
Following the life test, the dissipation factor shall
meet the initial requirement; the capacitance change
shall not exceed ± 10%; the leakage current shall not
exceed 125% of the initial requirement.
10.
Vibration Tests: Capacitors shall be subjected to
vibration tests in accordance with the following criteria.
10.1
Capacitors shall be secured for test by means of a
rigid mounting using suitable brackets.
10.2
Low Frequency Vibration: Vibration shall consist
of simple harmonic motion having an amplitude of
0.03" [0.76mm] and a maximum total excursion of
0.06" [1.52mm], in a direction perpendicular to the
major axis of the capacitors.
10.2.1 Vibration frequency shall be varied uniformly between
the approximate limits of 10 Hz to 55 Hz during a
period of approximately one minute, continuously for
1.5 hours.
10.2.2 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during the
final 30 minutes of the test. The AC voltage applied
shall not exceed 2 volts rms.
10.2.3 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
10.2.4 Following the low frequency vibration test, capacitors
shall meet the original requirements for capacitance,
dissipation factor and leakage current.
10.3
High Frequency Vibration: Vibration shall consist of
a simple harmonic motion having an amplitude of
Document Number 40002
Revision 27-Oct-04
10.3.4 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during the
last cycle. The AC voltage applied shall not exceed 2
volts rms.
10.3.5 Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
10.3.6 There shall be no mechanical damage to these
capacitors as a result of these tests.
10.3.7 Following the high frequency vibration test, capacitors
shall meet the original limits for capacitance,
dissipation factor and leakage current.
11.
Acceleration Test:
11.1
Capacitors shall be rigidly mounted by means of
suitable brackets.
11.2
Capacitors shall be subjected to a constant
acceleration of 100 g for a period of 10 seconds in
each of 2 mutually perpendicular planes.
11.2.1 The direction of motion shall be parallel to and perpendicular to the longitudinal axis of the capacitors.
11.3
Rated DC voltage shall be applied during acceleration
test.
11.3.1 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during test.
The AC voltage applied shall not exceed 2 volts rms.
11.4
Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
11.5
There shall be no mechancial damage to these
capacitors as a result of these tests.
11.6
Following the acceleration test, capacitors shall
meet the original limits for capacitance, dissipation
factor and leakage current.
For technical questions, contact [email protected]
www.vishay.com
23
293D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
12.
12.1
Capacitors shall be rigidly mounted by means of
suitable brackets. The test load shall be distributed
uniformly on the test platform to minimize the effects
of unbalanced loads.
12.1.1 Test equipment shall be adjusted to produce a shock
of 100 g peak with the duration of 6 mS and sawtooth
waveform at a velocity change of 9.7 ft./sec.
12.2
12.3
+ 125°C (+ 3°C, - 0°C) for 30 minutes, then
+ 25°C (+ 10°C, - 5°C) for 5 minutes for 5 cycles.
Shock Test:
Capacitors shall be subjected to 3 shocks applied in
each of 3 directions corresponding to the 3 mutually
perpendicular axes of the capacitors.
14.3
Capacitors shall show no evidence of harmful or
extensive corrosion, obliteration of marking or
other visible damage.
14.4
Following the thermal shock test, capacitors shall
meet the original requirements for leakage current and
dissipation factor. Capacitance change shall not
exceed ± 5% of the original measured value.
15.
Soldering Compatibility:
15.1
Resistance to Solder Heat: Capacitors will
withstand exposure to + 260°C + 5°C for 10 seconds.
Rated DC voltage shall be applied during test.
12.3.1 An oscilloscope or other comparable means shall be
used in determining electrical intermittency during
tests. The replacement voltage applied shall not
exceed 2 volts rms.
15.1.1 Following the resistance to soldering heat test,
capacitance, dissipation factor and DC leakage
current shall meet the initial requirement.
15.2
Electrical tests shall show no evidence of intermittent
contacts, open circuits or short circuits during these
tests.
Solderability: Capacitors will meet the solderability
requirements of ANSI/J-STD-002, Test B (MIL-STD202, method and test S.)
16.
There shall be no mechanical damage to these
capacitors as a result of these tests.
Terminal Strength: Per UEC-384-3, minimum of
5N shear force.
17.
Following the shock test, capacitors shall meet the
original limits for capacitance, dissipation factor and l
leakage current.
Environmental: Mercury, CFC and ODS materials
are not used in the manufacture of these capacitors.
18.
Flammability: Encapsulant materials meet UL94 V0
with an oxygen index of 32%.
13.
Moisture Resistance:
19.
13.1
Capacitors shall be subjected to temperature cycling
at 90% to 95% relative humidity, from + 25°C to
+65°C to + 25°C (+ 10°C, - 2°C) over a period of 8
hours per cycle for 1000 hours.
Capacitor Failure Mode: The predominant failure
mode for solid tantalum capacitors is increased
leakage current resulting in a shorted circuit. Capacitor failure may result from excess forward or reverse
DC voltage, surge current, ripple current, thermal
shock or excessive temperature.
13.2
Following the moisture resistance test, the leakage
current and dissipation factor shall meet the initial
requirements, and the change in capacitance shall
not exceed ± 10%.
The increase in leakage is caused by a breakdown of
the Ta2O5 dielectric. For additional information on
12.4
12.5
12.6
14.
Thermal Shock:
14.1
Capacitors shall be conditioned prior to temperature
cycling for 15 minutes at + 25°C, at less than 50%
relative humidity and a barometric pressure at 28 to 31"
14.2
Capacitors shall be subjected to thermal shock in a
cycle of exposure to ambient air at :
- 55°C (+ 0°C,- 5°C) for 30 minutes, then
+ 25°C (+10°C, - 5°C) for 5 minutes, then
www.vishay.com
24
leakage failure of solid tantalum chip capacitors, refer
to Vishay Sprague Technical Paper, “Leakage Failure
Mode in Solid Tantalum Chip Capacitors.”
20.
Surge Current: All D and E case code 293D
capacitors are 100% surge current tested at + 25°C
and rated voltage. The total series circuit resistance
is 0.5 ohms. Each charge cycle of 0.10 seconds is
followed by a discharge cycle of 0.10 seconds. Three
surge cycles are applied. Each capacitor is tested
individually to maximize the peak charging current.
For technical questions, contact [email protected]
Document Number 40002
Revision 27-Oct-04
293D
Vishay Sprague
important that the equivalent Irms value be established
when calculating permissible operating levels. (Power
Dissipation calculated using + 25°C temperature rise.)
GUIDE TO APPLICATION
1.
A-C Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
Irms =
P
RESR
Case Code
where,
A
B
C
D
E
P
P = Power Dissipation in Watts @ + 25°C as
given in the table in Paragraph Number 5 (Power
Dissipation).
RESR = The capacitor Equivalent Series Resistance
at the specified frequency.
2.
0.075
0.085
0.110
0.150
0.165
0.025
6.
Printed Circuit Board Materials: Type 293D
capacitors are compatible with commonly used printed
circuit board materials (alumina substrates, FR4,
FR5, G10, PTFE-fluorocarbon and porcelanized
steel).
7.
Attachment:
7.1
Solder Paste: The recommended thickness of the
solder paste after application is .007" ± .001"
[.178mm ± .025mm]. Care should be exercised in
selecting the solder paste. The metal purity should
be as high as practical. The flux (in the paste) must
be active enough to remove the oxides formed on the
metallization prior to the exposure to soldering heat. In
practice this can be aided by extending the solder
preheat time at temperatures below the liquidous state
of the solder.
7.2
Soldering: Capacitors can be attached by
conventional soldering techniques - vapor phase,
infrared reflow, wave soldering and hot plate methods.
The Soldering Profile chart shows maximum
recomended time/temperature conditions for soldering. Attachment with a soldering iron is not recommended due to the difficulty of controlling temperature
and time at temperature.
8.
Cleaning (Flux Removal) After Soldering: The
293D is compatible with all commonly used solvents
such as TES, TMS, Prelete, Chlorethane, Terpene
and aqueous cleaning media. However, CFC/ODS
products are not used in the production of these
devices and are not recommended. Solvents containing methylene chloride or other epoxy solvents should
be avoided since these will attack the epoxy
encapsulation material.
8.1
When using ultrasonic cleaning, the board may
resonate if the output power is too high. This vibration
can cause cracking or a decrease in the adherence of
the termination. DO NOT EXCEED 9W/l @ 40kHz
for 2 minutes.
A-C Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
Vrms = Z
Maximum Permissible
Power Dissipation
@ + 25°C (Watts)
in free air
P
RESR
or, from the formula:
Vrms = Irms x Z
where,
P
=
Power Dissipation in Watts @ + 25°C as
given in the table in Paragraph Number 5
(Power Dissipation).
RESR = The capacitor Equivalent Series Resistance
at the specified frequency.
Z
= The capacitor impedance at the specified
frequency.
2.1
The sum of the peak AC voltage plus the DC voltage
shall not exceed the DC voltage rating of the
capacitor.
2.2
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10% of the DC rating at + 25°C.
3.
Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 10% of the DC rating at + 25°C, 5% of the
DC rating at + 85°C and 1% of the DC rating at +125°C.
4.
5.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25°C, the
permissible rms ripple current or voltage shall be
calculated using the derating factors as shown:
Temperature
Derating Factor
+ 25°C
+ 85°C
+ 125°C
1.0
0.9
0.4
Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the mounting
surface. Non-sinusoidal ripple current may produce
heating effects which differ from those shown. It is
Document Number 40002
Revision 27-Oct-04
For technical questions, contact [email protected]
www.vishay.com
25
293D
Vishay Sprague
GUIDE TO APPLICATION (Continued)
SOLDERING PROFILE
Recommended Solder Profile — Reflow
Recommended Solder Profile — Wave Solder
5 - 10 Sec.
300
Max. Recommended
260°C
250
250
200
200
150
130°C
150
Temperature Degrees Centigrade
Temperature Degrees Centigrade
300
300
100
100
50
50
250
0
50
100
150
200
200
150
150
130°C Typical
100
100
50
50
0
0
0
250
50
100
150
200
250
Time (Seconds)
Time (Seconds)
9.
250
200
0
0
300
245°C Typical
Recommended Mounting Pad Geometries: Proper mounting pad geometries are essential for successful solder
connections. These dimensions are highly process sensitive and should be designed to minimize component rework
due to unacceptable solder joints. The dimensional configurations shown are the recommended pad geometries for
both wave and reflow soldering techniques. These dimensions are intended to be a starting point for circuit board
designers and may be fine tuned if necessary based upon the peculiarities of the soldering process and/or circuit board
design.
RECOMMENDED MOUNTING PAD GEOMETRIES in inches [millimeters]
Wave Solder Pads
Reflow Solder Pads
D
D
C
B
E
E
C
B
A
A
Pad Dimensions
Pad Dimensions
Case
Code
A
A
(Min.)
0.034
[0.87]
B
(Nom.)
0.085
[2.15]
C
(Nom.)
0.053
[1.35]
D
(Nom.)
0.222
[5.65]
E
(Nom.)
0.048
[1.23]
B
0.061
[1.54]
0.085
[2.15]
0.065
[1.65]
0.234
[5.95]
C
0.061
[1.54]
0.106
[2.70]
0.124
[3.15]
D
0.066
[1.68]
0.106
[2.70]
E
0.066
[1.68]
P
0.034
[0.87]
www.vishay.com
26
Case
Code
A
A
(Min.)
0.071
[1.80]
B
(Nom.)
0.085
[2.15]
C
(Nom.)
0.053
[1.35]
D
(Nom.)
0.222
[5.65]
E
(Nom.)
0.048
[1.23]
0.048
[1.23]
B
0.110
[2.80]
0.085
[2.15]
0.065
[1.65]
0.234
[5.95]
0.048
[1.23]
0.337
[8.55]
0.050
[1.28]
C
0.110
[2.80]
0.106
[2.70]
0.124
[3.15]
0.337
[8.55]
0.050
[1.28]
0.175
[4.45]
0.388
[9.85]
0.050
[1.28]
D
0.118
[3.00]
0.106
[2.70]
0.175
[4.45]
0.388
[9.85]
0.050
[1.28]
0.106
[2.70]
0.175
[4.45]
0.388
[9.85]
0.050
[1.28]
E
0.118
[3.00]
0.106
[2.70]
0.175
[4.45]
0.388
[9.85]
0.050
[1.28]
0.085
[2.15]
0.053
[1.35]
0.222
[5.65]
0.048
[1.23]
P
0.071
[1.80]
0.085
[2.15]
0.053
[1.35]
0.222
[5.65]
0.048
[1.23]
For technical questions, contact [email protected]
Document Number 40002
Revision 27-Oct-04
293D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
.157 ± .004
[4.0 ± .10]
K
Max.
.059 + .004 - 0.0
[1.5 + .10 - 0.0]
.079 ± .002
[2.0 ± .050]
.024
[.600]
Max.
.069 ± .004
[1.75 ± .10]
A0
F
W
B0
K0
B1 Max.
P
Top Cover Tape
D1 Min.
Direction of Feed
TAPE SIZE B1 (Max.) D1 (Min.)
F
K (Max.)
8mm
0.165
[4.2]
0.039
[1.0]
0.138 ± 0.002
[3.5 ± 0.05]
0.094
[2.4]
12mm
0.323
[8.2]
0.059
[1.5]
0.217 ± 0.002
[5.5 ± 0.05]
0.177
[4.5]
P
A0B0K0
Notes:
A
B
K
are
determined
by component size.
0
0
0
0.157 ± 0.004 0.315 ± 0.012
The clearance between the component and the
[4.0 ± 1.0]
[8.0 ± 0.30]
cavity must be within 0.002" [0.05mm] minimum to
0.315 ± 0.004 0.472 ± 0.012 0.020" [0.50mm] maximum for 8mm tape and 0.002"
[8.0 ± 1.0]
[12.0 ± 0.30] [0.05mm] minimum to 0.026" [0.65mm] maximum
for 12mm tape.
Standard orientation is with
the cathode (-) nearest to the
sprocket holes per EIA-481-1
and IEC 286-3.
Top Cover
Tape Thickness
Carrier
W
Tape and Reel Specifications: All case codes are available
on plastic embossed tape per EIA-481-1. Tape reeling per
IEC 286-3 is also available. Standard reel diameter is 13"
[330mm]. 7" [178mm] reels are available.
The most efficient packaging quantities are full reel increments
on a given reel diameter. The quantities shown allow for the
sealed empty pockets required to be in conformance with
EIA-481-1. Reel size must be specified in the Vishay
Sprague part number.
Embossment
Units Per Reel
Cathode (-)
Anode (+)
Direction of Feed
Document Number 40002
Revision 27-Oct-04
Case
Code
Tape
Width
A
8mm
4mm
2000
9000
B
8mm
4mm
2000
8000
C
12mm
8mm
500
3000
D
12mm
8mm
500
2500
E
12mm
8mm
400
1500
P
8mm
4mm
3000
10000
For technical questions, contact [email protected]
Component 7" [178mm] 13" [330mm]
Reel
Reel
Pitch
www.vishay.com
27