SHARP LHF32J02

PRODUCT SPECIFICATIONS
®
Integrated Circuits Group
LH28F320BJE-PTTL90
Flash Memory
32M (2M × 16/4M × 8)
(Model No.: LHF32J02)
Spec No.: EL124011
Issue Date: April 17, 2000
SHARP
--
LHF32JO2
l Handle this document carefully for it contains material protected by international copyright law.
Any reproduction, full or in part, of this material is prohibited without the express written
permission of the company.
l When using the products covered herein, please observe the conditions written herein and the
. precautions outlined in the following paragraphs. In no event shall the company be liable for any
damages resulting from failure to strictly adhere to these conditions and precautions.
(1) The products covered herein are designed and manufactured for the following application
areas. When using the products covered herein for the equipment listed in Paragraph (2),
even for the following application areas, be sure to observe the precautions given in
Paragraph (2). Never use the products for the equipment listed in Paragraph (3).
*Office electronics
. t
l Instrumentation and measuring equipment
*Machine tools
*Audiovisual equipment
*Home appliance
@Communication equipment other than for trunk lines
(2) Those contemplating using the products covered herein for the following equipment which
demands high reliability, should first contact a sales representative of the company and then
accept responsibility for incorporating into the design fail-safe operation, redundancy, and
other appropriate measures for ensuring reliability and safety of the equipment and the
overall system.
*Control and safety devices for airplanes, trains, automobiles,
transportation equipment
*Mainframe computers
*Traffic control systems
l Gas leak detectors and automatic cutoff devices
*Rescue and security equipment
*Other safety devices and safety equipment, etc.
and other
(3) Do not use the products covered herein for the following equipment which demands
extremely high performance in terms of functionality, reliability, or accuracy.
*Aerospace equipment
l Communications equipment for trunk lines
*Control equipment for the nuclear power industry
*Medical equipment related to life support, etc.
(4) Please direct all queries and comments regarding the interpretation of the above three
Paragraphs to a sales representative of the company.
l Please direct all queries regarding the products covered herein to a sales representative of the
company.
Rev. 1.26
SHARI=
LHF32JO2
1
CONTENTS
PAGE
1 INTRODUCTION..
PAGE
5 DESIGN CONSIDERATIONS
....................................... 27
............................................................
3
1.1 Features ........................................................................
3
5.1 Three-Line Output Control ........................................ 27
1.2 Product Overview.. ...................................................... .3
5.2 RY/BY# and WSIM Polling ....................................... 27
1.3 Product Description.. .................................................... 4
5.3 Power Supply Decoupling ......................................... 27
1.3.1 Package Pinout .: .......................... ...... ..-..... .............. 4
5.4 V,,
Trace on Printed Circuit Boards ..................... 27
1.3.2 Block Organization ................................................ .4
5.5 V,, . V,,,,
RP# Transitions .................................... 27
5.6 Power-Up/Down
2 PRINCIPLES OF OPERATION.. ..................................... .8
2.1 Data Protection.. .......................................................... .8
3 BUS OPERATION ........................................................... .9
3.1 Read ..............................................................................
9
3.2 Output Disable.. ........................................................... .9
Protection.. ..................................... 28
5.7 Power Dissipation ......................................................
28
5.8 Data Protection Method.. ........................................... 28
6 ELECTRICAL
SPECIFICATIONS
................................ 29
6.1 Absolute Maximum Ratings ...................................... 29
6.2 Operating Conditions.. ...............................................
29
29
3.3 Standby .........................................................................
9
6.2.1 Capacitance.. ........................................................
3.4 Reset .............................................................................
9
6.2.2 AC Input/Output Test Conditions ........................ 30
3.5 Read Identifier Codes.. ............................................... 10
6.2.3 DC Characteristics.. .............................................
3.6 OTP(One Time Program) Block.. .............................. 10
6.2.4 AC Characteristics - Read-Only Operations.. ...... 33
3.7 Write.. .........................................................................
6.2.5 AC Characteristics - Write Operations ................ 36
11
31
6.2.6 Alternative CE#-Controlled Writes.. .................... 38
1COMMAND
DEFINITIONS..
......................................... 11
6.2.7 Reset Operations ..................................................
40
4.1 Read Array Command.. .............................................. 13
6.2.8 Block Erase, Full Chip Erase, Word/Byte Write and
4.2 Read Identifier Codes Command ............................... 13
Lock-Bit Configuration Performance ................. 41
4.3 Read Status Register Command.. ............................... 13
4.4 Clear Status Register Command.. ............................... 13
7 PACKAGE
AND PACKING
SPECIFICATIONS
.. .... ... . 42
4.5 Block Erase Command.. ............................................. 14
4.6 Full Chip Erase Command.. ....................................... 14
4.7 Word/Byte Write Command.. ..................................... 14
4.8 Block Erase Suspend Command ................................ 15
4.9 Word/Byte Write Suspend Command.. ....................... 15
4.10 Set Block and Permanent Lock-Bit Command.. ....... 16
4.11 Clear Block Lock-Bits
Co mmand.. .......................... 16
4.12 OTP Program Command .......................................... 17
4.13 Block Locking by the WP# ...................................... 17
Rev. 1.26
SHAI?P
2
LHF32JO2
LH28F320BJE-PTTL90
32M-BIT ( 2Mbit x16 / 4Mbit x8 )
Boot Block Flash MEMORY
I
I
I
I
x8 or x 16 Operation
-
90ns(Vcc=2.7V-3.6V)
-
Operating Temperature
0°C to +7O”C
-
Typ. 4pA (Vcc=3.0V) Standby Current
Automatic Power Savings Mode Decreases I,-,
Static Mode
Typ. 12OpA (Vc,=3.0V, TA=+25”C, f=32kHz)
Read Current
I Optimized Array Blocking Architecture
-
Two 4K-word (8K-byte) Boot Blocks
Six 4K-word @K-byte) Parameter Blocks
Sixty-three 32K-word (64K-byte) Main Blocks
Top Boot Location
I Extended Cycling Capability
-
Minimum 100,000 Block Erase Cycles
IHARP’s LH28F320BJE-P’TTL90
vide range of applications.
Absolute Protection with VccwSVcm,
Block Erase, Full Chip Erase, Word/Byte Write and
Lock-Bit Configuration Lockout during Power
Transitions
Block Locking with Command and WP#
Permanent Locking
n Automated Block Erase, Full Chip Erase,
Word/Byte
Write and Lock-Bit Configuration
Low Power Management
-
Word/Byte Write Suspend to Read
Block Erase Suspend to Word/Byte Write
Block Erase Suspend to Read
Enhanced Data Protection Features
High-Performance Read Access Time
-
I
3963 word + 4 word Program only array
User-Configurable
-
I
-
OTP(One Time Program) Block
-
I
n Enhanced Automated Suspend Options
Low Voltage Operation
Single Voltage
- v cc =v ,,=2.7V-3.6V
in
-
Command User Interface (CUI)
Status Register (SR)
n SRAM-Compatible
Write
Interface
H Industry-Standard Packaging
-
4%Lead TSOP
n ETOXTM* Nonvolatile Flash Technology
n CMOS Process (P-type silicon substrate)
n Not designed or rated as radiation hardened
Flash memory is a high-density, low-cost, nonvolatile. read/write storage solution for a
,H28F320BJE-PTTL90 can operate at V,,=2.7V-3.6V
and V,,,- -2.lV-3.6V
apability realize battery life and suits for cellular phone application.
or 11.7V-12.3V. Its low voltage operation
is Boot, Parameter and Main-blocked architecture, low voltage and extended cycling provide for highly flexible component
uitable for portable terminals and personal computers. Its enhanced suspend capabilities provide for an ideal solution for code
data storage applications.
‘or secure code storage applications, such as networking, where code is either directly executed out of flash or downloaded to
)RAM, the LH28F320BJE-PTTL90
offers foui levels of protection: absolute protection with VCCW<VCCWLfi selective
ardware block locking or flexible software block locking. These alternatives give designers ultimate control of their code
:curity needs.
he LH28F320BJE-PITL90
is manufactured on SHARP‘s 0.25pm ETOXT”*
:andard package: the 4%lead TSOP, ideal for board constrained applications.
process technology. It come in industry-
ETOX is a trademark of Intel Corporation
Rev. 1.25
SHAR!=
--
LJSF32JO2
1 INTRODUCTION
This
datasheet
contains
LH28F320BJE-PI-l-L90
specifications. Section 1 provides a flash memory
overview. Sections 2, 3, 4 and 5 describe the memory
organization and functionality. Section 6 covers electrical
specifications.
1.1 Features
Key enhancements of LH28F320BJE-PTTL90
Flash memory are:
boot block
*Single low voltage operation
*Low power consumption
*Enhanced Suspend Capabilities
*Boot Block Architecture
Please note following:
l VCCvtK
has been lowered to l.OV to support 2.7V3.6V block erase, full chip erase, word/byte write and
lock-bit configuration operations. The V,,
voltage
transitions to GND is recommended for designs that
switch V,,, off during read operation.
1.2 Product Overview
The LH28F320BJE-PTTL90 is a high-performance 32MIit Boot Block Flash memory organized as 2M-word of 16
)its or 4M-byte of 8 bits. The 2M-word/4M-byte
of data is
u-ranged in two 4K-word/8K-byte
boot blocks, six 4Kvord/8K-byte parameter blocks and sixty-three 32Kvord/64K-byte
main blocks which are individually
:rasable, lockable and unlockable in-system. The memory
nap is shown in Figure 3.
The dedicated V ccw pin gives complete data protection
vhen Vccw<V,m,.
, Command User Interface (CUI) serves as the interface
etween the system processor and internal operation of the
evice. A valid command sequence written to the CUI
vitiates device automation. An internal Write State
lachine (WSM) automatically executes the algorithms
Id timings necessary for block erase. full chip erase.
,ord/byte write and lock-bit configuration operations.
A block erase operation erases one of the device’s 32K
word/64K-byte blocks typically within 1.2s (3V V,,. 3\
Vccw), 4K-word/8K-byte
blocks typically within 0.6s (3\
V,,. 3V Vccw) independent of other blocks. Each block
can be independently erased minimum 100.000 times
Block erase suspend mode allows system software tc
suspend block erase to read or write data from any other
block.
Writing memory data is performed in word/byu
increments of the device’s 32K-word blocks typically
within 33~s (3V V,,. 3V V,,,),
6JK-byte block!
typically within 31ps (3V V,,. 3V Vccw). 4K-wore
blocks typically within 36~s (3V V,,. 3V Vccw). 8Kbyte blocks typically within 32~s (3V V,,. 3V Vccw).
Word/byte write suspend mode enables the system to reac
data or execute code from any other flash memory array
location.
‘I
Individual block locking uses a combination of bits
seventy-one block lock-bits, a permanent lock-bit ant
WP# pin. to lock and unlock blocks. Block lock-bits gate
block erase, full chip erase and word/byte
write
operations. while the permanent lock-bit gates block lockbit modification and locked block alternation. Lock-bil
configuration operations (Set Block Lock-Bit,
Set
Permanent Lock-Bit
and Clear Block
Lock-Bits
commands) set and cleared lock-bits.
The status register indicates when the WSM’s block erase.
full chip erase, word/byte write or lock-bit configuration
operation is finished.
The RY/BY# output gives an additional indicator of WSM
activity by providing both a hardware signal of status
(versus software polling) and status masking (interrupt
masking for background block erase, for example). Status
polling using RYiBY# minimizes both CPU overhead and
system power consumption. When low, RY/J3Y# indicates
that the WSM is performing a block erase, full chip erase.
word/byte write or lock-bit configuration. RY/BY#-high 2
indicates that the WSM is ready for a new command.
block erase is suspended (and word/byte write is
inactive), word/byte write is suspended, or the device is in
reset mode.
Rev. 1.25
SHARP
LHF32JO2
4
1
The access time is 90ns (tAvQv) over the operating
temperature range (0°C to +7O”C) and V, supply voltage
range of 2.7V-36V.
1.3 Product Description
The Automatic Power Savings (APS) feature substantially
reduces active current when the device is in static mode
(addresses not switching). In APS mode. the typical I,-,
current is 4pA (CMOS) at 3.OV V,,.
LH28F320BJE-PTTL90
Boot Block Flash memory
available in 48-lead TSOP package (see Figure 2).
When CE# and RP# pins are at V,,. the I,, CMOS
standby mode is enabled. When the RP# pin is at GND,
reset mode is enabled which minimizes power
consumption and provides write protection. A reset time
(tpHQv) is required from RP# switching high until outputs
are valid. Likewise, the device has a wake time (tpHEL)
from RP#I-high until writes to the CUI are recognized.
With RP# at GND, the WSM is reset and the status
register is cleared.
Please do not execute reprogramming “0” for the bit which
has already been programed “0”. Overwrite operation may
generate unerasable bit. In case of reprogramming “0” to
the data which has been programed “1”.
.Program “0” for the bit in which you want to change
data from “1” to “0”.
.Program “1” for the bit which has already been
programmed “0”.
For example, changing data from “10111101”
“10111100” requires “11111110” programming.
to
1.3.1 Package Pinout
is
1.3.2 Block Organization
This product
features an asymmetrically-blocked
architecture providing system memory integration. Each
erase block can be erased independently of the others up to
100,000 times. For the address locations of the blocks, see
the memory map in Figure 3.
Boot Blocks: The boot block is intended to replace a
dedicated boot PROM in a microprocessor
or
microcontroller-based system. This boot block 4K words
(4,096words)
features hardware controllable
writeprotection to protect the crucial microprocessor boot code
from accidental modification. The protection of the boot
block is controlled using a combination of the V,,,
RP#,
WP# pins and block lock-bit.
Parameter Blocks: The boot block architecture includes
parameter blocks to facilitate storage of frequently update
small parameters that would normally require an
EEPROM. By using software techniques, the word-rewrite
functionality of EEPROMs can be emulated. Each boot
block component contains six parameter blocks of JK
words (4.096 words) each. The protection of the parameter
block is controlled using a combination of the Vccw, RP#
and block lock-bit.
Main Blocks: The reminder is divided into main blocks for
data or code storage. Each 32M-bit device contains sixtythree 32K words (32.768 words) blocks. The protection of
the main block is controlled using a combination of the
Vccw. RP# and block lock-bit.
Rev. 1.X
--
LHF32JO2
5
r
Figure I. Block Diagram
Al5
Al4
43
Al?
All
40
A¶
‘48
A19
ho
WE#
RP#
vccw
WP#
RY/BY#
48
A17
2
AS
A4
A3
A?
Al
45
Ez 0
2
3
6
1
8
9
10
11
12
13
1-l
15
16
17
1s
19
20
21
22
23
24
48-LEAD
STANDARD
TSOP
PINOUT
12mm x 20mm
TOP VIEW
48 I
47 I
Al6
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
DQI~/AI
DQ7
DQIJ
DQs
DQu
BYTE#
GND
W5
DQlz
DQI
vcc
DQII
DQ3
DQIO
DQz.
DQ9
DQI
DQs
DQo
OE#
GND
Cl3
‘%I
Figure 2. TSOP &Lead
Pinout
Rev. 1.2
SHARP
LHF32JO2
Symbol
TYW
A-1
INPUT
A,-*20
1DQ,-DQ,,
INPUT/
OUTPUT
CE#
INPUT
RP#
INPUT
OE#
INPUT
WE#
INPUT
WI%
INPUT
BYl-E#
INPUT
RY/BY#
OPEN
DRAIN
OUTPUT
Vccw
SUPPLY
vcc
SUPPLY
GND
SUPPLY
Table 1. Pin Descriptions
Name and Function
ADDRESS INPUTS: Inputs for addresses during read and write operations. Addresses are
internally latched during a write cycle.
A-t: Lower address input while BYTE# is V,,. A-, pin changes DQ, j pin while BYTE# is V,,.
A, j-A20: Main Block Address.
A,1-A20: Boot and Parameter Block Address.
DATA INPUT/OUTPUTS: Inputs data and commands during CUI write cycles: outputs data
during memory array, status register and identifier code read cycles. Data pins float to highimpedance when the chip is deselected or outputs are disabled. Data is internally latched during a
write cycle. DQ*-DQtj pins are not used while byte mode (BYTE#=V,).
Then. DQtj pin
changes A-, address input.
CHIP ENABLE: Activates the device’s control logic, input buffers, decoders and sense amplifiers.
CE#-high deselectsthe device and reduces power consumption to standby levels.
RESET: Resets the device internal automation. RP#-high enables normal operation. When driven
low, RP# inhibits write operations which provides data protection during power transitions. Exit
from reset mode sets the device to read array mode. RP# must be V, during power-up.
OUTPUT ENABLE: Gates the device’s outputs during a read cycle.
WRITE ENABLE: Controls writes to the CUI and array blocks. Addresses and data are latched on
the risine edge of the WE# uulse
WRITE PROTECT: When WP# is V,. boot blocks cannot be written or erased. When WP# is
V,, locked boot blocks can not be written or erased. WP# is not affected parameter and main
blocks.
BYTE ENABLE: BYTE# V, places device in byte mode (x8). All data is then input or output on
DQ,,. and DQs-, j float. BYTE# V,, places the device in word mode (x 16), and turns off the A-t
input buffer.
READY/BUSY#: Indicates the status of the internal WSM. When low, the WSM is performing an
internal operation (block erase, full chip erase, word/byte write or lock-bit configuration).
RY/BY#-high Z indicates that the WSM is ready for new commands. block erase is suspended.
and word/byte write is inactive, word/byte write is suspended, or the device is in reset mode.
BLOCK ERASE, FULL CHIP ERASE, WORD/BYTE WRITE OR LOCK-BIT
CONFIGURATION
POWER SUPPLY: For erasing array blocks. writing words/bytes or
configuring lock-bits. With VCCWIVCCWLK. memory contents cannot be altered. Block erase, full
chip erase. word/byte write and lock-bit configuration with an invalid Vccw (see 6.2.3 DC
Characteristics) produce spurious results and should not be attempted. Applying 12V+O.3V to
Vccw during erase/write can only be done for a maximum of 1000 cycles on each block. Vccw
may be connected to 12V&.3V for a total of 80 hours maximum.
DEVICE POWER SUPPLY: Do not float any power pins. With V,,IV,,,,
all write attempts to
the flash memory are inhibited. Device operations at invalid V,, voltage (see 6.2.3 DC
Characteristics) produce spurious results and should not be attempted.
GROUND: Do not float any ground pins.
Rev. 1.25
SHARP
--
LHF32J02
r
7
r
Top Boot
L%(rA(
EFlTF
iffooo
IFEFFF
ho-A01
[AGO-A-II
OEFWF
OEOQCO
ODFFFF
OCOCOO
OBFFFF
OBOIMO
OAFFFF
n . nnnn
32KW/64KB
Mam
Block
59
33KW/h-LKB
Main
Block
60
32KW/64KB
3?KW/h4KB
Main
Main
Block
Block
61
62
‘I ::g
I ;;;z
OIFFFF
1 0 I two
CQmtT;
imoo
II-E@Xl
IFDFFF
IFWOO
IFCFFF
IFCWO
IFBFFF
IFBCQO
IFAFFF
IFAOOO
ll?xFF
1F9m
IFSFFF
lF8lXKJ
lF7tFF
1’s
IEBMX)
lE7Ftl=
IEOWO
lDFFFl=
lD8KlC
lD7FFF
IWO00
ICFFFF
Ic8cixl
IUFFF
ICWOO
IBFFFF
IWOW
lB7FFF
IBoo
IAHFF
IA8000
lA7FFF
IALXXIO
19FFFF
l98cm
197FFF
190ooO
18FFFF
188cco
187FFF
18OooO
17FFFF
178000
177FFF
17ocQO
16tTFF
l68ONl
167lTF
16OGQO
15FFFF
lS8CCil
IVFFF
l5Oca
I.R=FF
I J8000
IUFFF
IUHXW)
IWFFF
138OW
137m
13OcQo
12FFFF
I28000
117FFF
IIOIXH
I I I-TFT
118000
117tTF
I IOocdI
I 0twF
108ooO
107tFF
ICWXX)
JKWIXKB
Boot Block
_1.
L”W
?FDFFF
‘FCOOO
3FBm
:r&E
3F8Mnl
3F7FFF
3F6000
3FSFFF
3MMX)
3F3FFF
3F1000
3FlFW
3FOiXMl
3EFFFF
3EOooO
3DFFFF
3wOQO
3cFFFF
3cmo
3BFFFF
3BCWO
3AFFFF
3AOCHl
39FFFF
390000
38FFFF
3scml
37FFFF
37oOm
36FFFF
36OMM
35FFFF
35OMx)
3aT-FF
?10000
33FFFF
330000
32tTF-F
310000
3lFFFF
31ooOQ
3oFFFF
3cQOm
?FFFFF
2FOOOO
EFFFF
lEOOO0
?DlTFF
JDCCCiI
2CFFFF
?CoooO
2BFtFF
?BooOO
MFFFF
2A0000
?9FFFF
19om
XWFFF
28OCUl
YFFFF
?7ccm
36FFFF
26OWX
25FFFF
250000
24=FFF
140000
I3FmF
230000
2ZFFFF
22oooo
1llTFF
210000
lOFFFF
30Ofl00
Figure 3. Memory Map
Rev. I.25
SHARI=
--
LHF32JO2
2 PRINCIPLES OF OPERATION
The LH28F320BIEPTTL90
Flash memory includes an
on-chip WSIM to manage block erase, full chip erase,
word/byte write and lock-bit configuration functions. It
allows for: fixed power supplies during block erase. full
chip erase, word/byte write and lock-bit configuration, and
minimal processor overhead with RAM-like interface
timings.
After initial device power-up or return from reset mode
(see section 3 Bus Operations). the device defaults to read
array mode. Manipulation of external memory control pins
allow array read, standby and output disable operations.
Status register and identifier codes can be accessed
through the CUI independent of the V,,
voltage. High
voltage on V,,
enables successful block erase, full chip
erase, word/byte write and lock-bit configurations. All
functions associated with altering memory contents-block
erase, full chip erase, word/byte
write.
lock-bit
zonfigurationt status and identifier codes-are accessed via
he CUI and verified through the status register.
Commands are written using standard microprocessor
write timings. The CUI contents serve as input to the
WSM, which controls the block erase, full chip erase,
word/byte write and lock-bit configuration. The internal
Algorithms are regulated by the WSM. including pulse
.epetition, internal verification and margining of data.
iddresses and data are internally latched during write
:ycles. Writing the appropriate command outputs array
lata, accesses the identifier codes or outputs status register
iata.
8
Interface software that initiates and polls progress of block
erase, full chip erase, word/byte write and lock-bit
configuration can be stored in any block. This code is
copied to and executed from system RAM during flash
memory updates. After successful completion, reads are
again possible via the Read Array command. Block erase
suspend allows system software to suspend a block erase
to read/write data from/to blocks other than that which is
suspend. Word/byte write suspend allows system software
to suspend a word/byte write to read data from any other
flash memory array location.
2.1 Data Protection
memory contents cannot be
When V,&VccwLK.
altered. The CUI, with two-step block erase, full chip
erase, word/byte write or lock-bit configuration command
sequences, provides protection from unwanted operations
even when high voltage is applied to Vccw. All write
functions are disabled when V,, is below the write
lockout voltage V,,, or when RP# is at V,. The device’s
block locking capability provides additional protection
from inadvertent code or data alteration by gating block
erase. full chip erase and word/byte write operations.
Refer to Table 5 for write protection alternatives.
Rev. 1.25
SHARI=
--
LHF32JO2
3 BUS OPERATION
3.4 Reset
The local CPU reads and writes flash memory in-system.
All bus cycles to or from the flash memory conform to
standard microprocessor bus cycles.
RP# at V,, initiates the reset mode.
3.; Read
Information can be read from any block, identifier codes
or status register independent of the Vccw voltage. RP#
can be at V,.
The first task is to write the appropriate read mode
command (Read Array. Read Identifier Codes or Read
Status Register) to the CUI. Upon initial device power-up
or after exit from reset mode. the device automatically
resets to read array mode. Six control pins dictate the data
flow in and out of the component: CE#, OE#, BYTE#,
WE#, RP# and WP#. CE# and OE# must be driven active
to obtain data at the outputs. CE# is the device selection
control. and when active enables the selected memory
device. OE# is the data output (DQo-DQ,,) control and
when active drives the selected memory data onto the I/O
bus. BYTE# is the device I/O interface mde control. WE#
must be at V,,, RP# must be at V,,. and BYTE# and WP#
must be at V, or V,,. Figure 16. 17 illustrates read cycle.
3.2 Output Disable
With OE# at a logic-high level (V,,). the device outputs
Ire disabled. Output pins (DQ,-DQ,j)
are placed in a
ligh-impedance state.
3.3 Standby
9
In read modes: RP#-low deselects the memory. places
output drivers in a high-impedance state and turns off all
internal circuits. RP# must be held low for a minimum of
1OOns. Time tpHQv is required after return from reset
mode until initial memory access outputs are valid. After
this wake-up interval, normal operation is restored. The
CUI is reset to read array mode and status register is set to
80H.
During block erase. full chip erase. word/byte write or
lock-bit configuration modes. RP#-low will abort the
operation. RY/BY# remains low until the reset operation
is complete. Memory contents being altered are no longer
valid; the data may be partially erased or written. Time
tpBwL is required after RP# goes to logic-high (V,,)
before another command can be written.
As with any automated device. it is important to assert
RP# during system reset. When the system comes out of
reset, it expects to read from the flash memory. Automated
flash memories provide status information when accessed
during block erase. full chip erase, word/byte write or
lock-bit configuration modes. If a CPU reset occurs with
no flash memory reset. proper CPU initialization may not
occur because the flash memory may be providing status
information instead of assay data. SHARP’s
flash
memories allow proper CPU initialization following a
system reset through the use of the RP# input. In this
application, RP# is controlled by the same RESET# signal
that resets the system CPU.
C1E# at a logic-high level (V,,) places the device in
standby mode which substantially reduces device power
:onsumption. DQ,-DQ,,
outputs are placed in a highmpedance state independent of OE#. If deselected during
)lock erase. full chip erase. word/byte write or lock-bit
:onfiguration, the device continues functioning, and
:onsuming active power until the operation completes.
Rev. 1.15
SHARP
--
LHF32JO2
10
.5 Read Identifier Codes
3.6 OTP(One Time Program) Block
he read identifier codes operation outputs the
manufacturer code. device code. block lock configuration
Ides for each block and the permanent lock configuration
)de (see Figure 4). Using the manufacturer and device
Ides, the system CPU can automatically match the device
ith its proper algorithms. The block lock and permanent
mck configuration codes identify locked and unlocked
ocks and permanent lock-bit setting.
The OTP block is a special block that can not be erased.
The block is divided into two parts. One is a factory
program area where a unique number can be written
according to customer requirements in SHARP factory.
This factory program area is “READ ONLY” (Already
locked). The other is a customer program area that can be
used by customers. This customer program area can be
locked. After locking, this customer program area is
protected permanently.
Top Boa
3FFFFF
3FEOO6
3FEOO5
3FEoo.t
3FEcm3
3FEOOO
3FDFFF
3FCCQ6
3FCOO5
3FCOO.t
3FCCO3
3FCMH)
3FBFFF
3FACC-5
3FAOO5
3FAOO.l
3FAOO3
3FACNM
IFCFFF;
; 3F9FFF
IF9000
i
(Parameter
; 3F1000
Blocks 1 through 4)
The OTP block is read in Configuration Read Mode by
writing Read Identifier Codes command(90H). To return
to Read Array Mode, write Read Array command(FFH).
The OTP block is programmed by writing OTP Program
command(COH). First write OTP Program command and
then write data with address to the device (See Figure 5).
If OTP program is failed, SR.J(WORD/BYTE
WRITE
AND SET LOCK-BIT STATUS) bit is set to “1”. And if
this OTP block is locked, SR.I(DEVICE
PROTECT
STATUS) bit is set to “1” too.
The OTP block is also locked by writing OTP Program
command(COH). First write OTP Program command and
then write data “FFFDH” with address “80H” to the
device. Address “80H” of OTP block is OTP lock
information. Bit 0 of address “80H”
means factory
program area lock status(“1” is “NOT LOCKED”. “0” is
“LOCKED”).
Bit 1 of address “SOH” means customer
program area lock status. The OTP lock information can
not be cleared, after once it is set.
3FIFFF
Reserved
Parameter
for Future Implementation
Block 5 Lock Confieumtion
Code
3FMW6
3FooOS
3FOOOJ
3FOOO3
OOIFFF
ooom
3FoooO
3EFFFF
~~__~_~^~~~~~-~l~----~---------~~-
IFOWl
Reserved
IFOiXQ
IEFFFF
j
008000
i
(Man
Reserved
000080
for Future Implementr&ion
Main Block 0,
Blocks
forFuture
1 throyh
61)
Customer
3E0006
3EOOo5
3EOOOJ
3EOCO3
3EMXW)
1
oooO85
Program
Area
1
1 OOOIOA
j
i 3DFFFF
Implementation
1
Customer
Factory
Program
Program
Area Lock
Area Lock
Figure 5. OTP Block Address Map
Figure 4. Device Identifier Code Memory Map
Rev. 1.35
SHARP
--
LHF32JO2
3.7
Write
Writing commands to the CUI enable reading of device
data and identifier codes. They also control inspection and
clearing of the status register. When V,,=2.7V-3.6V
and
the CUI additionally controls block
VCCW=VCCWH1/2~
erase, full chip erase, word/byte write and lock-bit
configuration.
11
The CUI does not occupy an addressable memory
location. It is written when WE# and CE# are active. The
address and data needed to execute a command are latched
on the rising edge of WE# or CE# (whichever goes high
first). Standard microprocessor write timings are used.
Figures 18 and 19 illustrate WE# and CE# controlled write
operations.
4 COMMAND
The Block Erase command requires appropriate command
data and an address within the block to be erased. The Full
Chip Erase command requires appropriate command data
and an address within the device. The Word/Byte Write
command requires the command and address of the
location to be written. Set Permanent and Block Lock-Bit
commands require the command and address within the
device (Permanent Lock) or block within the device
(Block Lock) to be locked. The Clear Block Lock-Bits
command requires the command and address within the
device.
DEFINITIONS
When the V,,
voltage IVCCWLK. Read operations from
the status register, identifier codes. or blocks are enabled.
enables successful block
Placing
VccWH1i2
on
VCCW
erase. full chip erase. word/byte write and lock-bit
configuration operations.
Device operations are selected by writing specific
commands into the CUI. Table 3 defines these commands.
Table 2.1. Bus Operations (BYTEI
Read Identifier Codes
X
Write
X
X
673
DIN
VI,
VI,
VI,
VIL
NOTES:
memory contents can be read. but not altered. 1. Refer to DC Characteristics. When VccwlVccwLK.
2. X can be V, or V,, for control pins and addresses, and VcCWLK or VCCWH,,2 for V,,,.
See DC Characteristics for
VCCWLK voltages.
3. RY/BY# is V,, when the WSM is executing internal block erase, full chip erase, word/byte write or lock-bit configuration
algorithms. It is High Z during when the WSM is not busy, in block erase suspend mode (with word/byte write inactive).
word/byte write suspend mode or reset mode.
4. RP# at GND-cO.2V ensures the lowest power consumption.
5. See Section 4.2 for read identifier code data.
6. Command writes involving block erase, full chip erase, word/byte write or lock-bit configuration are reliably executed
when V ccw=VccwHt/q
and Vcc=2.7V-3.6V.
7. Refer to Table 3 for vahd D,, during a write operation,
8. Never hold OE# low and WE# low at the same timing.
Rev. 1.25
--
LHF32JO2
12
Table 3. Command Definition&lo)
Full Chip Erase
II
Word/Byte Write
Block Erase and Word/Byte
Write Suspend
Block Erase and Word/Byte
Write Resume
Set Block Lock-Bit
Clear Block Lock-Bits
Set Permanent Lock-Bit
OTP Program
2
I
2
1
5.6
1 Write
1
X
1
30H
1 Write
I
x
) 4yy~
1 Write
1
X
)
DOH
I Write
I
WA
/
WD
I
I/
I
1
>
.j
Write
X
BOH
1
5
Write
,X
DOH
2
2
2
2
8
Write
Write
Write
Write
X
X
X
X
60H
60H
60H
COH
7.8
9
Write
Write
Write
Write
BA
X
X
OA
OlH
DOH
FIH
OD
1. BUS operations are defined in Table 2.1 and Table 2.2.
2. X=Any valid address within the device.
IA=Identifier Code Address: see Figure 4.
BA=Address within the block being erased.
WA=Address of memory location to be written.
OA=Address of OTP block to be written: see Figure 5.
3. ID=Data read from identifier codes.
SRD=Data read from status register. See Table 6 for a description of the status register bits.
WD=Data to be written at location WA. Data is latched on the rising edge of WE# or CE# (whichever goes high first).
OD=Data to be written at location OA. Data is latched on the rising edge of WE# or CE# (whichever goes high first).
4. Following the Read Identifier Codes command. read operations access manufacturer, device. block lock configuration and
permanent lock configuration codes. See Section 4.2 for read identifier code data.
5. If WP# is V,, boot blocks are locked without block lock-bits state. If WP# is Vt,, boot blocks are locked by block lockbits. The parameter and main blocks are locked by block lock-bits without WP# state.
6. Either 4OH or 10H are recognized by the WSM as the word/byte write setup.
7. The clear block lock-bits operation simultaneously clears all block lock-bits.
8. If the permanent lock-bit is set, Set Block Lock-Bit and Clear Block Lock-Bits commands can not be done.
9. Once the permanent lock-bit is set. permanent lock-bit reset is unable.
10. Commands other than those shown above are reserved by SHARP for future device implementations and should not be
used.
Rev. 1.25
SHARP
LHF32JO2
4.1 Read Array Command
4.3 Read Status Register Command
Upon initial device power-up and after exit from reset
mode. the device defaults to read array mode. This
operation is also initiated by writing the Read Array
command. The device remains enabled for reads until
another command is written. Once the internal WSM has
started a block erase, full chip erase. word/byte write or
lock-bit configuration the device will not recognize the
Read Array command until the WSM completes its
operation unless the WSM is suspended via an Erase
Suspend or Word/Byte Write Suspend command. The
Read Array command functions independently of the
Vccw voltage and RP# can be V,,.
The status register may be read to determine when a block
erase, full chip erase, word/byte write or lock-bit
configuration is complete and whether the operation
completed successfully. It may be read at any time by
writing the Read Status Register command. After writing
this command, all subsequent read operations output data
from the status register until another valid command is
written. The status register contents are latched on the
falling edge of OE# or CE#, whichever occurs. OE# or
CE# must toggle to VIH before further reads to update the
status register latch. The Read Status Register command
functions independently of the Vccw voltage. RP# can be
VII-t.
4.2 Read Identifier Codes Command
4.4 Clear Status Register Command
The identifier code operation is initiated by writing the
Read Identifier Codes command. Following the command
write, read cycles from addresses shown in Figure 4
retrieve the manufacturer, device. block lock configuration
and permanent lock configuration codes (see Table 4 for
Identifier code values). To terminate the operation. write
another valid command. Like the Read Array command,
he Read Identifier
Codes command
functions
ndependently of the V,-w voltage and RP# can be V,,.
‘allowing
the Read Identifier Codes command, the
‘allowing information can be read:
Table 4. Identifier Codes
Address(‘)
Code
Data(3)
[A,,-A,1 PQ,-DQ,l
Manufacture Code
Device Code
Block Lock Configuration
*Block is Unlocked
*Block is Locked
OOOOOH
BOH
OOOOlH
E2H
B A( I,+2 ‘~~~~~~~ .,,.
.,...
DQ,=O
Status register bits SR.5. SR.4. SR.3 or SR.l are set to
“1”s by the WSM and can only be reset by the Clear Status
Register command. These bits indicate various failure
conditions (see Table 6). By allowing system software to
reset these bits. several operations (such as cumulatively
erasing multiple blocks or writing several words/bytes in
sequence) may be performed. The status register may be
polled to determine if an error occurred during the
sequence.
To clear the status register. the Clear Status Register
command (50H) is written. It functions independently of
the applied Vccw Voltage. RP# can be V,,. This
command is not functional during block erase or
word/byte write suspend modes.
DQ,= 1
*Reserved for Future Use
Permanent Lock Configuration
BA selects the specific block lock configuration code
to be read. See Figure 4 for the device identifier code
memory map.
!. A-, don’t care in byte mode.
1. DQtj-DQ9 outputs OOH in word mode.
_I
Rev. 1.25
SHARP
LHF32JO2
4.5 Block Erase Command
Erase is executed one block at a time and initiated by a
two-cycle command. A block erase setup is first written,
followed by an block erase confirm. This command
sequence requires appropriate sequencing and an address
within the block to be erased (erase changes all block data
to FFFFH/FFH). Block preconditioning. erase. and verify
are handled internally by the WSM (invisible to the
system). After the two-cycle block erase sequence is
written, the device automatically outputs status register
data when read (see Figure 6). The CPU can detect block
erase completion by analyzin_g the output data of the
RY/BY# pin or status register bit SR.7.
When the block erase is complete, status register bit SR.5
should be checked. If a block erase error is detected, the
status register should be cleared before system software
attempts corrective actions. The CUI remains in read
status register mode until a new command is issued.
This two-step command sequence of set-up followed by
execution ensures that block contents are not accidentally
erased. An invalid Block Erase command sequence will
result in both status register bits SR.4 and SR.5 being set
to “1”. Also. reliable block erasure can only occur when
Vcc=2.7V-3.6V
and VCCW=VCCwH1,?. In the absence of
this high voltage, block contents are protected against
erasure. If block erase is attempted while VCCWIVCCWLK.
SR.3 and SR.5 will be set to “1”. Successful block erase
requires for boot blocks that WP# is V,, and the
corresponding block lock-bit be cleared. In parameter and
main blocks case, it must be cleard the corresponding
block lock-bit. If block erase is attempted when the
excepting above conditions. SR.1 and SR.5 will be set to
“1”.
4.6 Full Chip Erase Command
I’his command followed by a confirm command erases all
af the unlocked blocks. A full chip erase setup (30H) is
!irst written. followed by a full chip erase confirm (DOH).
4fter a confirm command is written. device erases the all
mlocked blocks block by block. This command sequence
.equires appropriate sequencing. Block preconditioning.
:rase and verify are handled internally by the WSIM
invisible to the system). After the two-cycle full chip
:rase sequence is written. the device automatically outputs
status register data when read (see Figure 7). The CPU can
ietect full chip erase completion by analyzing the output
lata of the RY/BY# pin or status register bit SR.7.
Nhen the full chip erase is complete. status register bit
lR.5 should be checked. If erase error is detected. the
tatus register should be cleared before system software
ittempts corrective actions. The CUI remains in read
status register mode until a new command is issued. I
error is detected on a block during full chip erase
operation. WSIM stops erasing. Full chip erase operatior
start from lower address block. finish the higher addres!
block. Full chip erase can not be suspended.
This two-step command sequence of set-up followed b)
execution ensures that block contents are not accidentall)
erased. An invalid Full Chip Erase command sequence
will result in both status register bits SR.4 and SR.5 being
set to “1”. Also, reliable full chip erasure can only OCCUI
In the
when V,,- -2 7V-3.6V and VCCw=VCCWHln.
absence of this high voltage. block contents are protectec
against erasure. If full chip erase is attempted while
V CCWIVCCwrK.
SR.3 and SR.5 will be set to “1”
Successful full chip erase requires for boot blocks thal
WP# is V,, and the corresponding block lock-bit be
cleared. In parameter and main blocks case, it must be
cleard the corresponding block lock-bit. If all blocks are
locked. SR.1 and SR.5 will be set to “1”.
4.7 Word/Byte Write Command
Word/Byte write is executed by a two-cycle command
sequence. Word/Byte write setup (standard 40H 01
alternate 10H) is written. followed by a second write that
specifies the address and data (latched on the rising edge
of WE#). The WSM then takes over, controlling the
word/byte write and write verify algorithms internally.
After the word/byte write sequence is written, the device
automatically outputs status resister data when read (see
Figure 8). The CPU can detect the completion of the
word/byte write event by analyzing the RY/BY# pin OI
status register bit SR.7.
When word/byte write is complete, status register bit SR.J
should be checked. If word/byte write error is detected. the
status register should be cleared. The internal WSM verify
only detects errors for “1”s that do not successfully write
to “0”s. The CUI remains in read status register mode until
it receives another command.
Reliable word/byte
writes can only occur when
V,,=2.7V-3.6V
and VCCw=VCCWHIR. In the absence of
this high voltage. memory contents are protected against
word/byte writes. If word/byte write is attempted while
VCCW<VCCwtK. status register bits SR.3 and SR.4 will be
set to “I”. Successful word/byte write requires for boot
blocks that WP# is V,, and the corresponding block lockbit be cleared. In parameter and main blocks case, it must
be cleard the corresponding block lock-bit. If word/byte
write is attempted when the excepting above conditions.
SR. 1 and SR.-l will be set to “I”.
Rev. 1.25
SHAi?l=
LHF32JO2
4.8
Block Erase Suspend Command
The Block Erase Suspend command allows block-erase
interruption to read or word/byte write data in another
block of memory. Once the block erase process starts,
writing the Block Erase Suspend command requests that
the WSM suspend the block erase sequence at a
predetermined point in the algorithm. The device outputs
status register data when read after the Block Erase
Suspend command is written. Polling status register bits
SR.7 and SR.6 can determine when the block erase
operation has been suspended (both will be set to “1”).
RY/BY# will also transition to High Z. Specification
twHRz2 defines the block erase suspend latency.
When Block Erase Suspend command write to the CUI, if
block erase was finished. the device places read array
mode. Therefore, after Block Erase Suspend command
write to the CUI, Read Status Register command (70H)
has to write to GUI, then status register bit SR.6 should be
checked for places the device in suspend mode.
At this point, a Read Array command can be written to
read data from blocks other than that which is suspended.
A Word/Byte Write command sequence can also be issued
during erase suspend to program data in other blocks.
Using the Word/Byte Write Suspend command (see
Section 4.9), a word/byte write operation can also be
suspended. During a word/byte write operation with block
erase suspended, status register bit SR.7 will return to “0”
and the RY/BY# output will transition to VOL. However,
SR.6 will remain “1” to indicate block erase suspend
status.
I’he only other valid commands while block erase is
suspended are Read Status Register and Block Erase
Resume. After a Block Erase Resume command is written
:o the flash memory, the WSM will continue the block
xase process. Status register bits SR.6 and SR.7 will
automatically clear and RY/BY# will return to VOL. After
he Erase Resume command is written, the device
automatically outputs status register data when read (see
3gure 9). V,,,
must remain at V,,,,,*
(the same
Vrccw level used for block erase) while block erase is
uspended. RP# must also remain at V,,. WP# must also
,emain at V,, or V,, (the same WP# level used for block
:rase). Block erase cannot resume until word/byte write
operations initiated during block erase suspend have
:ompleted.
1.5
4.9
Word/Byte
Write Suspend Command
The Word/Byte Write Suspend command allows
word/byte write interruption to read data in other flash
memory locations. Once the word/byte write process
starts, writing the Word/Byte Write Suspend command
requests that the WSM suspend the Word/Byte write
sequence at a predetermined point in the algorithm. The
device continues to output status register data when read
after the Word/Byte Write Suspend command is written.
Polling status register bits SR.7 and SR.2 can determine
when the word/byte write operation has been suspended
(both will be set to “1”). RY/BY# will also transition to
High Z. Specification tWHRZ1 defines the word/byte write
suspend latency.
When Word/Byte Write Suspend command write to the
CUI, if word/byte write was finished. the device places
read array mode. Therefore. after Word/Byte Write
Suspend command write to the CUI, Read Status Register
command (70H) has to write to CUI, then status register
bit SR.2 should be checked for places the device in
suspend mode.
At this point, a Read Array command can be written to
read data f$om locations other than that which is
suspended. The only other valid commands while
word/byte write is suspended are Read Status Register and
Word/Byte
Write Resume. After Word/Byte
Write
Resume command is written to the flash memory, the
WSM will continue the word/byte write process. Status
register bits SR.2 and SR.7 will automatically clear and
RY/BY# will return to V,,. After the Word/Byte Write
Resume command is written, the device automatically
outputs status register data when read (see Figure 10).
Vccw must remain at VCCWHIz (the same V,,
level
used for word/byte write) while in word/byte write
suspend mode. RP# must also remain at V,. WP# must
also remain at V,, or V,, (the same WP# level used for
word/byte write).
If the period of from Word/Byte Write Resume command
write to the GUI till Word/Byte Write Suspend command
write to the CUI be short and done again and again. write
time be prolonged.
f the period of from Block Erase Resume command write
the CUI till Block Erase Suspend command write to the
3JI be short and done again and again, erase time be
xolonged.
o
Rev. I .‘75
SHARP
LHF32JO2
4.10 Set Block and Permanent Lock-Bit
Commands
A flexible block locking and unlocking scheme is enabled
via a combination of block lock-bits. a permanent lock-bit
and WP# pin. The block lock-bits and WP# pin gates
program and erase operations while the permanent lock-bit
gates block-lock bit modification. With the permanent
lock-bit not set, individual block lock-bits can be set using
the Set Block Lock-Bit command. The Set Permanent
Lock-Bit command, sets the permanent lock-bit. After the
permanent lock-bit is set, block lock-bits and locked block
contents cannot altered. See Table 5 for a summary of
hardware and software write protection options.
Set block lock-bit and permanent lock-bit are executed by
a two-cycle
command sequence. The set block or
permanent lock-bit setup along with appropriate block or
device address is written followed by either the set block
Lock-bit confirm (and an address within the block to be
.ocked) or the set permanent lock-bit confirm (and any
levice address). The WSM then controls the set lock-bit
rlgorithm. After the sequence is written. the device
mtomatically outputs status register data when read (see
?gure 11). The CPU can detect the completion of the set
ock-bit event by analyzing the RY/BY# pin output or
;tatus register bit SR.7.
When the set lock-bit operation is complete. status register
Iit SR.3 should be checked. If an error is detected, the
‘tatus register should be cleared. The GUI will remain in
ead status register mode until a new command is issued.
this two-step sequence of set-up followed by execution
fnsures that lock-bits are not accidentally set. An invalid
;et Block or Permanent Lock-Bit command will result in
tatus register bits SR.4 and SR.5 being set to “1”. Also,
eliable operations occur only when Vcc=2.7V-3.6V and
I CCW=vCCWH1/2~ In the absence of this high voltage,
lck-bit contents are protected against alteration.
L successful set block lock-bit operation requires that the
ermanent lock-bit be cleared. If it is attempted with the
ermanent lock-bit set, SR.1 and SR.4 will be set to “1”
nd the operation will fail.
4.11 Clear Block Lock-Bits Command
All set block lock-bits are cleared in parallel via the Clear
Block Lock-Bits command. With the permanent lock-bit
not set, block lock-bits can be cleared using only the Clear
Block Lock-Bits command. If the permanent lock-bit is
set, block lock-bits cannot cleared. See Table 5 for a
summary of hardware and software write protection
options.
Clear block lock-bits operation is executed by a two-cycle
command sequence. A clear block lock-bits setup is first
written. After the command is written. the device
automatically outputs status register data when read (see
Figure 12). The CPU can detect completion of the clear
block lock-bits event by analyzing the RY/BY# Pin output
or status register bit SR.7.
When the operation is complete, status register bit SR.5
should be checked. If a clear block lock-bit error is
detected, the status register should be cleared. The CUI
will remain in read status register mode until another
command is issued.
This two-step sequence of set-up followed by execution
ensures that block lock-bits are not accidentally cleared.
An invalid Clear Block Lock-Bits command sequence will
result in status register bits SR.4 and SR.5 being set to “1”.
Also, a reliable clear block lock-bits operation can only
occur when V,-=2.7V-3.6V
and VCCw=VCCwH1,2. If a
clear block iock-bits operation is attempted while
Vc+V,,,,,
SR.3 and SR.5 will be set to “1”. In the
absence of this high voltage. the block lock-bits content
are protected against alteration. A successful clear block
lock-bits operation requires that the permanent lock-bit is
not set. If it is attempted with the permanent lock-bit set,
SR.1 and SR.5 will be set to “1” and the operation will
fail.
If a clear block lock-bits operation is aborted due to Vccw
or Vcc transitioning out of valid range or RP# active
transition, block lock-bit
values are left in an
undetermined state. A repeat of clear block lock-bits is
required to initialize block lock-bit contents to known
values. Once the permanent lock-bit is set. it cannot be
cleared.
Rev. 1.25
SHARP
LHF32JO2
4.12 OTP Program Command
1
3TP program is executed by a two-cycle command
sequence. OTP program command(COH) is written,
1rollowed by a second write cycle that specifies the address
i md data (latched on the rising edge of WE#). The WSM
t hen takes over, controlling the OTP program and program
\ verify
algorithms internally. After the OTP program
C:ommand sequence is completed, the device automatically
tutputs status register data when read (see Figure 13). The
; ZPU can detect the completion of the OTP program by
2analyzing the output data of the RY/BY#
pin or status
I egister bit SR.7.
(
I
Nhen OTP program is completed, status register bit SR.4
hould be checked. If OTP program error is detected, the
Status register should be cleared. The internal WSM verify
Conly detects errors
for “1”s that do not successfully
F brogram to “0”s. The CUI remains in read status register
n node until it receives other commands.
\
s
Fleliable OTP program can be executed only when
\ I,,=2.7V-3.6V
and VCCw=VCCWHln. In the absence of
tlhis voltage, memory contents are protected against OTP
programs. If OTP program is attempted whik
Vccw5Vt--,,.
status register bits SR.3 and SR.4 is se
to “1”. If OTP write is attempted when the OTP Lock-bi
is set, SR.l and SR.4 is set to “1”.
4.13 Block Locking by the WP#
This Boot Block Flash memory architecture features twc
hardware-lockable boot blocks so that the kernel code foi
the system can be kept secure while other blocks arc
programmed or erased as necessary.
The lockable two boot blocks are locked when WP#=V,,
any program or erase operation to a locked ‘block will
result in an error, which will be reflected in the status
register. For top configuration, the top two boot blocks are
lockable. For the bottom configuration, the bottom twc
boot blocks are lockable. If WP# is V, and block lock.
bit is not set, boot block can be programmed or erased
normally (Unless V,,
is below VCCwtK). WP# is valid
only two boot blocks, other blocks are not affected.
Table 5. Write Protection Alternatives
Rev. 1.26
SHARI=
18
LHF32JO2
WSMS
1
7
BESS
6
1 ECBLBS
Table 6. Status Register Definition
1 WBWSLBS 1 VCCWS
1 WBWSS
5
4
3
1
.2
DPS
R
1
0
1
NOTES:
SR.7 = WRITE STATE iMACHINE STATUS (WSMS)
1 = Ready
0 = Busy
Check RY/BY# or SR.7 to determine block erase. full chip
erase, word/byte write or lock-bit configuration completion.
SR.6-0 are invalid while SR.7=“0”.
SR.6 = BLOCK ERASE SUSPEND STATUS (BESS)
1 = Block Erase Suspended
0 = Block Erase in Progress/Completed
SR.5 = ERASE AND CLEAR BLOCK L&X-BITS
STATUS (ECBLBS)
1 = Error in Block Erase, Full Chip Erase or Clear Block
Lock-Bits
0 = Successful Block Erase. Full Chip Erase or Clear
Block Lock-Bits
SR.4 = WORD/BYTE WRITE AND SET LOCK-BIT
STATUS (WBWSLBS)
1 = Error in Word/Byte Write or Set Block/Permanent
Lock-Bit
0 = Successful Word/Byte Write or Set Block/Permanent
Lock-Bit
SR.1 does not provide a continuous indication of permanent
and block lock-bit and WP# values. The WSM interrogates
the permanent lock-bit, block lock-bit and WP# only after
Block Erase, Full Chip Erase, Word/Byte Write or Lock-Bit
Configuration command sequences. It informs the system.
depending on the attempted operation, if the block lock-bit is
set, permanent lock-bit is set and/or WP# is V,,. Reading
the block lock and permanent lock configuration codes after
writing the Read Identifier Codes command indicates
permanent and block lock-bit status.
SR.2 = WORD/BYTE WRITE SUSPEND STATUS
(WBWSS)
1 = Word/Byte Write Suspended
0 = Word/Byte Write in Progress/Completed
SR.1 = DEVICE PROTECT STATUS (DPS)
1 = Block Lock-Bit, Permanent Lock-Bit and/or WP#
Lock Detected, Operation Abort
0 = Unlock
FOR FUTURE ENHANCEMENTS
SR.3 does not provide a continuous indication of V,-cw
level. The WSM interrogates and indicates the V,--w level
only after Block Erase. Full Chip Erase, Word/Byte Write or
Lock-Bit Configuration command sequences. SR.3 is not
guaranteed to reports accurate feedback only when
VCCW’VCCWHl12.
SR.3 = Vccw STATUS (VCCWS)
1 = Vccw Low Detect, Operation Abort
0 = Vccw OK
GR.0 = RESERVED
If both SR.5 and SR.4 are “1”s after a block erase. full chip
erase or lock-bit configuration attempt. an improper
command sequence was entered.
(R)
SR.0. is reserved for future use and should be masked out
when polling the status resister.
Rev. 1.25
SHARI=
LHF32JO2
19
r
SLan
BU,
opryiom
Comments
Command
Dam=7OH
Wrne 70H
Add-X
.:
(heck SR.7
Sldhy
W”te
I=WSM Ready
O=WSM Buy
Dao=?OH
Ad&X
Emc Setup
Wme ?OH
I
+
Wnle WH.
Block Address
Full Sfam.s
Check if Desired
FULL. STATL’S CHECK PROCEDL’RE
BUS
ops!uon
Cmlme”u
Command
Standby
I
Check SR.3
I=Vccw Erra D&Cl
Check SR.5
I=Block Erase Enc.
Comm.nd
Sqwnce
Block Ervs Error
Figure 6. Automated
Block Erase Flowchart
,
Rev. 1.X
LHF32JO2
20
(7)
v
wrm
rnH
+
Read Stmus
Wnre 30H
L
I
Wnle DOH
Red Skws
Rcg,ster
9
Full status check can be done af,er each lid1 chip erase.
0
SR.7=
Write FFH after the bet oprauon
80 place Lnca
in rend array mode.
I
Full Status
Check ,f Dared
-r-’
Full Ch,p Erase
Complete
FL’LL STATUS CHECK
PROCEDURE
Read %m. Regnter
Daw(Sce Above)
BUS
opmuoo
COmlllCdS
Command
Check SR.3
I=Vccw Erra Detect
Standby
Check SR.1
,=Dcv,cr Pra*ct DrteEt
Staodby
(All Bloclu are laked)
Device Raea
Error
cheek SR.4.S
Standby
Bad, I=Command
Cheek SR.5
I&d, Cb,p Erase Error
Standby
comrmnd
S,quence Error
Scqwnce
SR.5. SR.4. SR.3 nml SR.1 are only cleared by Ihe Clcu Suws Rsg~sr Command
where muhiplc
in wer
blc&s are erased before full ~tatu.sis checked.
If ci-rcs IS detected. clear ,hc Status Regster before a”emptw
reU,‘or ahcr error recovery.
Full Oup G-se Error
Full Ch,p Gus
S”cc<,rf”l
Figure 7. Automated Full Chip Erase Flowchart
Rev. 1.25
SHARP
LHF32JO2
r
Read Swus
Rtgstcr
SR.7=
0
I
Write 4OH OT IOH
g
.;
wnu WordKlgrc
Data and Ad&w
Full Status
Check d &sued
y%&
FULL STATL’S CHECK PROCEDDRE
WordlBjw
Wrnz Succzssiul
Figure 8. Automated Word/Byte Write Flowchart
Rev. 1.25
SHARI=
--
LHF32JO2
WWC
22
ErAYe
Suspend
Sollu
had
Wnlz
Data=BOH
Addr=X
Regmer Data
Addr=X
Erase
ReSUiV
Da=DOH
Addr=X
Bbck Emu Completed
Figure 9. Block Erase Suspend/Resume Flowchart
Rev. 1.25
SHARP
--
23
LHF32JO2
Command
W”lC
Commrnta
Dam=DOH
Ad&X
Figure 10. Word/Byte Write Suspend/Resume Flowchart
Rev. 1.25
SHARt=
--
LHF32JO2
BUS
operaron
24
Command
Cornmenu
I
Das70H
Addr=X
Swtw Reg,rts Data
Read
Check SR.7
I=WSM Ready
Standby
G=WSM Bury
Dam=.ZQH
AddzX
DatsOIH~Blwk).
BlocWDence
Address
FL’LL STATL’S CHECK PROCEDCRE
BUS
operauoa
Command
I
Cheek SR.3
Standby
l=VccH.
Ena Detect
Cheek SR. 1
I=Dwlcc RaeLZ DelCd
Pe,,,w,en, Lock-B,1 II Scr
(SC, Bluk Lock-B,1 Opxrauoa)
Chsck SR.J.5
Bolh I=Cammnnd Sequence Enor
Command Scqwnce
Set Lock-BtI Error
Figure 11. Set Block and Permanent Lock-Bit Flowchart
-I
Rev. 1.25
--
LHF32JO2
25
r
Comments
Dam=70H
Wnta
Addr=X
SU.IU Regstrr Data
Read
Check SR.7
I=WSM Ready
Standby
QWSM
FULL STATLS
Busy
CHECK PROCEDL’RE
Rend Status Re$,ner
am&Y Above,
Bus
OperJuon
stmdby
Device Raea
Command
I
cheek SR.3
,cV~~
Erra Dcrzct
Error
Command Sequence
“car
Block Leek-Bm
Rev. 1.25
--
LHF32JO2
26
r
BUS
openuo.
Cornmenu
Command
Check SR.7
Standby
I=WSM Ready
QWSM
setup OTP Rogml
FLU
Buy
Ds,=COH
Ad&X
STAT-L’S CHECK PROCEDL’RE
Standby
Standby
Cbcck SR.1
I=Dcrice Raect
Deted
Figure 13. Automated OTP Program Flowchart
Rev. 1.25
SHARP
LHF32JO2
27
5 DESIGN CONSIDERATIONS
5.3 Power Supply Decoupling
5.1 Three-Line Output Control
Flash memory power switching characteristics require
careful device decoupling. System designers are interested
in three supply current issues; standby current levels,
active current levels and transient peaks produced by
falling and rising edges of CE# and OE#. Transient current
magnitudes depend on the device outputs’ capacitive and
inductive loading. Two-line control and proper decoupling
capacitor selection will suppress transient voltage peaks.
Each device should have a O.lpF ceramic capacitor
connected between its V,, and GND and between its
V,,,
and GND. These high-frequency, low inductance
capacitors should be placed as close as possible to package
leads. Additionally. for every eight devices. a 4.7pF
electrolytic capacitor should be placed at the array’s power
supply connection between V,, and GND. The bulk
capacitor will overcome volta_pe slumps caused by PC
board trace inductance.
The device will often be used in large memory arrays.
SHARP provides three control inputs to accommodate
multiple memory connections. Three-line control provides
for:
a. Lowest possible memory power dissipation.
b. Complete assurance that data bus contention will not
occur.
To use these control inputs efficiently, an address decoder
should enable CE# while OE# should be connected to all
memory devices and the system’s READ# control line.
This assures that only selected memory devices have
active outputs while deselected memory devices are in
standby mode. RP# should be connected to the system
POWERGOOD signal to prevent unintended writes during
system power transitions. POWERGOOD
should also
toggle during system reset.
5.2 RY/BY# and WSM Polling
RY/BY# is an open drain output that should be connected
to V,, by a pull up resistor to provides a hardware method
of detecting block erase. full chip erase. word/byte write
and lock-bit configuration completion. It transitions low
after block erase, full chip erase. word/byte write or lockbit configuration commands and returns to V,, (while
RY/BY# is pull up) when the WSM has finished executing
the internal algorithm.
RY/BY# can be connected to an interrupt input of the
system CPU or controller. It is active at all times. RY/BY#
is also High Z when the device is in block erase suspend
(with word/byte write inactive), word/byte write suspend
3r reset modes.
5.4 VCCW Trace on Printed Circuit Boards
Updating flash memories that reside in the target system
requires that the printed circuit board designer pay
attention to the Vccw Power supply trace. The Vccw pin
supplies the memory cell current for word/byte writing
and block erasing. Use similar trace widths and layout
considerations given to the V,, power bus. Adequate
V ccw supply traces and decoupling will decrease Vccw
voltage spikes and overshoots.
5.5 Vcc, VCCW, RP# Transitions
Block erase, full chip erase,.word/byte write and lock-bit
configuration are not guaranteed if V,-, falls outside of a
valid VCCWH1,7, range. V,, falls outside of a valid 2.7V3.6V range, or RP##Vm. If V,,-w error is detected, status
register bit SR.3 is set to “1” along with SR.4 or SR.5.
depending on the attempted operation. If RP# transitions
to V, during block erase, full chip erase. word/byte write
or lock-bit configuration. RY/BY# will remain low until
the reset operation is complete. Then. the operation will
abort and the device will enter reset mode. The aborted
operation may leave data partially altered. Therefore. the
command sequence must be repeated after normal
operation is restored. Device power-off or RP# transitions
to V,, clear the status register.
The GUI latches commands issued by system software and
is not altered by Vccw or CE# transitions or WSM
actions. Its state is read array mode upon power-up. after
exit from reset mode or after V,, transitions below V,,,.
Rev. 1.25
SHARP
LHF32JO2
28
5.6 Power-Up/Down Protection
5.8 Data Protection Method
The device is designed to offer protection against
accidental block erase, full chip erase, word/byte write or
lock-bit configuration during power transitions. Upon
power-up, the device is indifferent as to which power
Supply (Vccw or V,,) powers-up first. Internal circuitry
resets the CUI to read array mode at power-up.
Noises having a level exceeding the limit specified in the
specification may be generated under specific operating
conditions on some systems. Such noises, when induced
onto WE# signal or power supply. may be interpreted as
false commands, causing undesired memory updating. To
protect the data stored in the flash memory against
unwanted overwriting. systems operating with the flash
memory should have the following write protect designs.
as appropriate:
A system designer must guard against spurious writes for
V,, voltages above VLKO when Vccw is active. Since
both WE# and CE# must be low for a command write,
driving either to V,, will inhibit writes. The CUPS twostep command sequence architecture prov.ides added level
Df protection against data alteration.
c
In-system block lock and unlock capability prevents
inadvertent data alteration. The device is disabled while
RP#=V, regardless of its control inputs state.’
5.7 Power Dissipation
When designing portable systems. designers must consider
lattery power consumption not only during device
operation, but also for data retention during system idle
ime. Flash memory’s nonvolatility increases usable
Iattery life because data is retained when system power is
.emoved.
1) Protecting data in specific block
When a lock bit is set. the corresponding block (includes
the 2 boot blocks) is protected against overwriting. By
setting a WP# to low. only the 2 boot blocks can be
protected against overwriting. By using this feature, the
flash memory space can be divided into the program
section (locked section) and data section (unlocked
section). The permanent lock bit can be used to prevent
false block bit setting. For further information on
setting/resetting lock-bit. refer to the specification. (See
chapter 4.10 and 4.11.)
2) Data protection through Vccw
When the level of V,-,, is lower than VCC,vrK (lockout
voltage), write operation on the flash memory is disabled.
All blocks are locked and the data in the blocks are
completely write protected. For the lockout voltage. refer
to the specification. (See chapter 6.2.3.)
3) Data protection through RP#
When the RP# is kept low during read mode. the flash
memory will be deep-power-down
mode. then write
protecting all blocks. When the RF% is kept low during
power up and power down sequence such as voltage
transition. write operation on the flash memory is disabled.
write protecting all blocks. For the details of RP# control.
refer to the specification. (See chapter 5.6 and 6.2.7.)
Rev. 1.25
SHARP
LHF32JO2
6 ELECTRICAL
SPECIFICATIONS
6.1 Absolute Maximum Ratings*
Operating Temperature
. During Read, Block Erase,
Full Chip Erase, Word/Byte Write
and Lock-Bit Configuration ...... ........ .. 0°C to +7O”C(r)
Storage Temperature
During under Bias . ..... ..... .. ........ ........ .. -10°C to +8O”C
During non Bias ...... ... ....... .......... ...... -65°C to +125”C
Voltage On Any Pin
(except V,, and V,,)
..... ...... -0SV to Vcc+0.5V(2)
V,, Supply Voltage .... ..... ... .._................. -0.2V to +4.6Vc2)
Vccw Supply Voltage.. ....................... -0.2V to +13.0V(2y3)
Output Short Circuit Current.. .............................. 100mAc4)
29
*WARNING:
Stressing the device beyond the ‘Absolute
Maximum Ratings” ma? cause permanent damage. These
are stress ratings only. Operation beyond the “Operating
Conditions”
is not recommended and extended e.xposure
beyond the “Operating
Conditions”
may affect device
reliability.
NOTES:
I. Operating temperatureis for commercialtemperature
product defined by this specification.
2. All specified voltages are with respect to GND.
Minimum DC voltage is -0.5V on input/output pins
and -0.2V on Vcc and Vccw pins. During transitions,
this level may undershootto -2.OV for periods<20ns.
Maximum DC voltage on input/output pins are
V,,+O.5V which, during transitions.may overshootto
Vcc+2.0V for periods<20ns.
3. Maximum DC voltage on Vccw may overshoot to
+13.OV for periods <20ns. Applying 12VkO.3V to
V,,,
during erase/write can only be done for a
maximum of 1000cycleson eachblock. V,,, may be
connected to 12V&3V for a total of 80 hours
maximum.
4. Output shortedfor no more than one second.No more
than one output shortedat a time.
5.2 Operating Conditions
Symbol
TA
Vcc
Temperatureand Vcc Operating Conditions
Parameter
Min.
Max.
Unit
OperatingTemperature
0
+70
“C
V,, Supply Voltage (2.7V-3.6V)
2.7
3.6
V
Test Condition
.AmbientTemperature
5.2.1 CAPACITANCE(l)
. Sampled,not 100%tested.
Rev. 1.25
SHARP
--
LHF32JO2
i.2.2 AC INPUT/OUTPUT
.
30
TEST CONDITIONS
~-YqL=z~~T
AC test inputs are driven at 2.7V for a Logic “1” and O.OV for aLogic
Input rise and fall times (107~ to 90%) ~10 ns.
“0”. Input riming begins, and output timing ends, at 1.35V.
Figure 14. Transient Input/Output Reference Waveform for Vcc=2.7V-3.6V
Test Configuration Capacitance Loading Value
Test Configuration
C,(pF)
V,,=2.7V-3.6V
50
DEVICE
UNDER
TEST
0
CL Includes Jig
Capacitance
-
OUT
CL
z
-
Figure 15. Transient Equivalent Testing Load Circuit
Rev. 1.25
SHARI=
LHJ532JO2
6.2.3 DC CHARACTERISTICS
1,
Parameter
Input Load Current
IL0
Output Leakage Current
kcs
V,, Standby Current
Sym.
DC Characteristics
1 V,,=2.7V-3.6V
Notes
Ma.
TYP.
1
20.5
1
193
1
Unit
PA
Test
Conditions
V,,=V,cMax.
V,,=V,,
or GND
kO.5
ClA
4
20
r-IA
V,,=V,,Max.
CE#=RP#=Vr&.2V
10
200
llA
VCCW=VCcwHll2
Vcc Auto Power-Save Current
kcwws
I,-,
V,,,
Word/Byte Write or
Block Erase Suspend Current
1
Rev. 1.76
SHARI=
LHF32JO2
D‘C Characteriistics (Continued)
V,,=2.7V-3.6V
Notes c
Min.
Max.
6
-0.5
0.4
6
Vcc
T
Sym.
V,
VII-I
Parameter
Input Low Voltage
Input High Voltage
vo,
Output Low Voltage
‘OH
Output High Voltage
T
Unit
V
Test Conditions
+0.5
7
56
Vcc=Vcc Min.
0.4
I nr =2.omA
I
6
ycc=Vcc Min.
I OH=-lOOpA
‘CCWLK
‘CCWHl
‘CCWHZ
V,,
Lockout during Normal
Operations
Vccw during Block Erase,Full’Chip
Erase.Word/Byte Write or Lock-Bit
Configurationbperations
V,,, during Block Erase,Full Chip
Erase,Word/Byte Write or Lock-Bit
ConfigurationOperations
V,, Lockout Voltage
I
46
1.0
V
2.7
3.6
V
11.7
12.3
V
7
VLKO
I
2.0
V
[OTES:
All currentsarein RMS unlessotherwisenoted.Typical valuesat nominalVcc voltameandT,=+25”C.
I,-,, andI,,,, are specifiedwith the device de-selected.If reador word/byte writtt& while in erasesuspendmode,the
device’s current draw is the sumof ICC,, or I,,,
and ICCRor I,,,
respectively.
IncludesRYlBY#.
Block erases,full chip erase.word/byte writes and lock-bit configurationsare inhibited when VccwSVcc~K. andnot
guaranteedin the rangebetweenVCCwLK(max.)and VCCWH,(min.),betweenVCCwH,(max.) and Vccwt&min.) and
above VccwB.,jmax.).
The Automatic Power Savings(APS) feature is placed automaticallypower savemodethat addresses
not switching more
than 300nswhile readmode.
Sampled,not 100%tested.
Applying 12V&.3V to Vccw during erase/writecan only be donefor a maximumof 1000cycles on eachblock. Vccw
may be connectedto 12Vti.3V for a total of 80 hoursmaximum.
Rev.
1.25
1
SHARP
-LHF32JO2
6.2.4 AC CHARACTERISTICS
Svm.
fA.lA,l
tAtrOV
tELOV
taun.7
tGLOV
tcr nv
tEHOZ
tGLOX
kHOZ
tOH
tFvov
tr;r A?
tcr
1.
2.
3.
4.
lx,
I
I Read Cvcle
- READ-ONLY
V ,,=2.7V-3.6V.
Parameter
33
OPERATIONS(*)
T,=O”C to +7O”C
1 Notes
Time
Address to Output Delay
CE# to Output Delay
RP# High to Outuut Delav
1OE# to Output Delay
1CE# to Outnut in Low Z
CE# High to Output in High Z
OE# to Output in Low Z
OE# High to Output in High Z . ’
Output Hold from Address, CE# or OE# Change. Whichever
Occurs Fist
) BYTE# to Output Delay
I BYTE# Low to Outnut in High Z
I CE# to BYTE# Hiah or Low
I
1
I
Min.
90
1
90
90
600
40
2
[
2
3
3
3
3
0
40
0
15
3
3
3.4
1 Unit
I ns
ns
ns
ns
ns
ns
ns
ns
ns
0
3
I
I
Max.
I
I
I
I
ns
I
90
25
5
I
ns
ns
ns
See AC Input/Output Reference Waveform for maximum allowable input slew rate.
OE# may be delayed up to tELQV-bLQV after the falling edge of CE# without impact on tELQv.
Sampled, not 100% tested.
If BYTE# transfer during reading cycle, exist the regulations separately.
Rev. 1.25
I
SHARP
--
LHF32JO2
Standby
Device
Address Selection
iDDRESSES
34
Data Valid
___________
Address Stable
___________
wE#fW)
:,I----
kLQV
kLQV
’
l
VOH
DATNDIQ)
:DQvDQd
HIGH Z
___________
VOL
tAVQV
IPHQV
Figure 16. AC Waveform for Read Operations
Rev. 1.25
SHARI=
LHF32JO2
II
Standby
Device
Address Selection
35
Data Valid
hH
ADDRESSES(A)
VIL
VIH
CE#03
VU
VIH
OEWG)
VU
hH
BYTE#Fl
VU
VOH
DATA(D/Q)
(DQo-DQ7)
VOL
kl.QZ
l
VOH
DATAIDIQ)
HIGH
Z
HIGH
Z
(DQs-DQIs)
VOL
Figure 17. BYTE# timing Waveform
Rev.
1.25
LHF32JO2
6.2.5 AC CHARACTERISTICS
- WRITE OPERATIONS(I)
\IoTEs:
1. Read timing characteristics during block erase, full chip erase. word/byte write and lock-bit configuration operations are
the same as during read-only operations. Refer to AC Characteristics for read-only operations.
1. Sampled, not 100% tested.
5. Refer to Table 4 for valid A,, and D,, for block erase. full chip erase. word/byte write or lock-bit configuration.
1. Vccw should be held at VCCWHI,Z until determination of block erase. full chip erase, word/byte write or lock-bit
configuration success (SR. l/3/4/5=0).
5. If BYTE# switch during reading cycle, exist the regulations separately.
Rev. 1.25
SHARP
--
37
LHF32JO2
rVIII
1
e----w
2
3
I
5
6
ADDRESSES(A)
VU
VIH
CE#(E)
VU
VIH
OE#(G)
VU
WE#(W)
DATACDIQ)
BYTE#O
n-Es:
VCC power-up and standby.
Write each setup command.
Write each confirm command or valid address and data
Automated eraSe or program delay.
Read statlls register data.
Write Read Array command.
Figure 18. AC Waveform for WE#-Controlled
Write Operations
Rev. 1.25
SHARP
--
LHF32JO2
6.2.6
ALTERNATIVE
CEKCONTROLLED
38
WRITES(*)
VOTES:
1. In systems where CE# defines the write pulse width (within a longer WE# timing waveform), all setup, hold, and inactive
WE# times should be measured relative to the CE# waveform.
2. Sampled, not 100% tested.
5. Refer to Table 4 for valid A,, and D,, for block erase, full chip erase, word/byte write or lock-bit configuration.
t. V,,,
should be held at VCCWH1,2 until determination of block erase. full chip erase, word/byte write or lock-bit
configuration success (SR. l/3/4/5=0).
j. If BYTE# switch during reading cycle, exist the regulations separately.
Rev. 1.26
SHARP
--
39
LHF32JO2
I
-e-v--
2
3
4
5
6
ADDRESSES(A)
DATACDIQ)
NOTES:
1. Vcc power-up and standby.
2. Write each setup command.
3. Write each confirm command or valid address and data.
4. Automated emse or program delay.
5. Read status register data.
6. Write Read Array command.
Figure
19. AC Waveform for CE#-Controlled Write Operations
Rev. 1.25
SHARP
LHF32JO2
6.2.7 RESET OPERATIONS
Hieh Z
RYiBY#(R)(‘b
GR.7)
VOL
(“0”)
VIH
RwP)
VIL
(A)ResetDuringRead
RY/BY#(R)
(SR.7)
Amy
Mode
Hieh Z
(‘?“,
VOL
(“0”)
VIH
=wP)
VIL
(B)Reset During
Block Erase, Full Chip Erase, Word/Byte
2.7V
Write or Lock-Bit
Configuration
L
vcc
I
VIL
-
tZVPH
-
VIH
I
~+w)
I
VIL
(C)RP#
rising Timing
Figure 20. AC Waveform for Reset Operation
Reset AC Specifications
Sym.
tPLPH
tPLRZ
Parameter
RP# Pulse Low Time
RP# Low to Resetduring Block Erase,Full Chip Erase,
Word/Byte Write or Lock-Bit Configumtion
V,, 2.7V to RP# High
Notes
2
I,2
Min.
100
M&X.
Unit
ns
30
PS
100
ns
233
t2VPH
NOTES:
1. If RP# is assertedwhile a block erase,full chip erase,word/byte write or lock-bit configuration operationis not executing,
the resetwill completewithin 1OOns.
2. A resettime, tpH v, is requiredfrom the later of RY/BY#(SR.7) going High Z(“1”) or RP# going high until outputsare
valid. Refer to A8 Characteristics- Read-Only Operationsfor tpHQv.
3. When the device power-up,holding RP#low minimum 1OOnsis requiredafter V,, hasbeenin predefinedrangeand also
hasbeenin stablethere.
I
Rev. 1.25
-41
LHF32J02
6.2.8
BLOCK ERASE,
CONFIGURATION
FULL CHIP ERASE,
PERFORMANCEt3)
WORD/BYTE
WRITE
AND LOCK-BIT
V,,=2.7V-3.6V.
Parameter
Sym.
Word Write Time
~WHQV~
tEHQVl
Byte Write Time
1Block Write Time
(In word mode)
Block Write Time
(In byte mode)
tWHQV?_
‘EHQV2
Block Erase Time
I
32K word Block
4K word Block
64K byte Block
I8K byte Block
( 32K wordBlock
I
I4K word Block
64K byteBlock
SK byte Block
32K word Bloc.I:K
I_
64K byte Block
4K word Block
8K bvte Block
1Full Chin Erase Time
tWHQL'3 Set Lock-Bit Time
tEHOV3
t
T ,=O”C to +7O”C
V ,,=2.7V-3.6V
Notes
Typ.“’
Max.
)
1
(
1
1
I
2
2
2
2
2
2
2
2
2
1
1
1
I
0.3
I
1.2
2
1
2
33
36
31
32
1.1
0.15
-a*
L.L
1
I1
1
I
1
0.6
1
84
200
200
200
200
4
0.5
‘)I
6
Vccw=l 1.7V-12.3V
Typ.’ ”
Max.
1
I
!
1
I
1
420
0.25
0.9
W
US
US
I
I
1
1
I1
1
6-t
us
S
S
1
I
1
S
I s I
S
I
1
s
2
56
200
42
US
2
I
5
0.69
S
Word/Byte Write Suspend Latency Time to
Read
4
6
15
6
1.5
!Js
Block Erase Suspend Latency Time to
Read
4
16
30
16
30
P
WHQVJ Clear Block Lock-Bits Time
tEHOV-!
b-RZ
tEHRZl
twnnz2
tEHRZ2
1
I
S
0.5
5
1
20
27
19
26
0.66
0.12
11.4 *
Unit
VOTES:
1. Typical values measured at T,=+25”C and V,,=3.OV, V,,,- -3 OV or 12.OV. Assumes corresponding lock-bits are not
set. Subject to change based on device characterization.
2. Excludes system-level overhead.
3. Sampled but not 100% tested.
4. A latency time is required from issuing suspend command(WE# or CE# going high) until RY/BY# going High Z or SR.7
going “1”.
Rev. 1.25
I
SHARF’
7 Package and packing
LHF32J02
-specification
1. Package Outline Specification
Refer to drawing No.AA
2. Markings
2 - 1. Marking contents
(1) Product name :
( 2 > Company name :
(3) Date code
(Example) _
1 1 4 2
LH28F320BJE-PTTL90
SHARP
-
Denotes the product ion ref .code (1-S)
Denotes the product ion week.
(Lower two digit of the year.)
w Denotes the product ion ref .code
(No marking , A , B , C )
(4) “JAPAN” is marked on the package when both wafer and assembly processes
are
done in Japan , indicating
the country of origin.
2-2.
Marking layout
Refer drawing No.AAl
14 2
(This layout does not define the dimensions of marking character
and marking position.)
3. Packing
Specification
(Dry packing for surface mount packages)
Dry packing is used for the purpose of maintaining IC quality after mounting
packages on the PCB (Printed
Circuit
Board).
When the epoxy resin which is used for plastic
packages is stored at high
humidity,
it may absorb 0.15% or more of its weight in moisture.
If the surface
mount type package for a relatively
large chip absorbs a large amount of moisture
between the epoxy resin and insert material (e.g. chip, lead frame) this moisture
may suddenly vaporize into steam when the entire package is heated during the
soldering
process (e.g. VPS). This causes expansion and results
in separation
between the resin and insert material,
and sometimes cracking of the package.
This dry packing is designed to prevent the above problem from occurring
in
surface mount packages.
3 - 1. Packing Materials
Material Specificaiton
Purpose
Mater ial Name
Conductive
plastic
(50devices/tray)
Fixing of device
Tray
-_--____________________________________-~--------------------------------------------------------------.-------------------------------------------------------Upper cover tray
Conductive plast ic
(ltray/case)
Fixing of device.
________________________________________~~--------------------------------------------------------------.-------------------------------------------------------~
Laminated
aluminum
bag
Aluminum
polyethylene
(lbag/case)
Drying
of device
-_______________________________________-~----------------------------------------------------------------------------------------------------------------------.
Desiccant
Silica
gel.
Drying
of
device
________________________________________-.--.-----------------------------------------------------------.
____________________----------------------------------~
P P band
Polypropylene
(3pcs/case)
Fixing of tray
-----_--________________________________-.--------------------------------------------.---------------.____________________-----------------------------------.
Inner
case
Card
board
(500device/case)
Packaging
of device
----------______________________________---------------------------------------------------------------.
--------------------------------------------------.-----.
Label
Paper
Indicates
part number,quantity
and date of manufacture
-----------___________________________________________________________________________________________________________
--______--.
Outer case
Card board
Cuter packing of tray
(Devices shall be placed into a tray in the same direction.)
SHARP
3-2.
Outline dimension
Refer to attached
LHF32J02
43
of tray
drawing
Storage and Opening of Dry Packing
4.
4-l.
Store under conditions
shown below before opening the dry packing
( 1) Temperature range : 5%40°C
: 80% RH or less
(2)
Humidity
4-2.
Notes on opening the dry packing
(1)
Before opening the dry packing, prepare a working table
grounded against ESD and use a grounding strap.
(2)
The tray has been treated to be conductive or anti-static.
device is transferred
to another tray, use a equivalent
which
is
If the
tray.
4 - 3. Storage after opening the dry packing
Perform the following
to prevent absorption
of moisture after opening.
(1)
After opening the dry packing, store the ICs in an environment with
temperature
of 5~25°C and a relative
humidity of 60% or less and
mount ICs within
72 hours after opening dry packing.
a
Baking (drying)
before mounting
( 1) Baking is necessary
(A)
If the humidity indicator
in the desiccant
becomes pink
(B)
If the procedure in section 4-3 could not be performed
( 2) Recommended baking conditions
If the above conditions
(A) and (B) are applicable,
bake it before
.
mounting. The recommended conditions
are 16-24 hours at 120°C.
Heat resistance
tray is used for shipping tray.
5.
Surface
Mount Conditions
Please perform the following
quality.
conditions
when mounting
ICs not to deteriorate
IC
5-l.Soldering
conditions(The
following
conditions
are valid only for one time soldering.)
Measurement Point
Mounting Method
Temperature and Duration
IC package
Reflow soldering
Peak temperature of 230°C or less,
surface
duration
of less than 15 seconds.
(air)
200°C or over,duration
of less than 40 seconds.
Temperature increase rate of l--4Vsecond
------“--‘-------“--------------~-------~-----------------------------------------------------------------------------.----------------------------------.
IC outer lead
Manual soldering
260C or less, duration of less
surface
than 10 sec.onds.
(soldering
iron)
5 - 2. Conditions
for removal of residual
(1)
Ultrasonic
washing power
(2)
Washing time
(3)
Solvent temperature
flux
: 25 Watts/liter
or less
: Total 1 minute maximum
: 15-40°C
SHARP
LHF32J02
LH28F320BJE-PTTL90
!
/SEE
DETAIL
25
f
A
DETAIL A
PKG.BASEPLANE
&zg
: UJAPAN.lJ
4ZZSb5%&~7---3R%
NOTES: Marking specification when “JAPAN”is marked.
5% j
!J- F&-k
! TIN-LEAD (!$@$ -1jXf7 9W-‘i#fj$klt,DJ ~$Wyltf’~ o
AME/ TSOP48-P-1220 LEADFINISH i PLATING NOTE Plastic body dimensions do not include burr
of resin.
4-G
;
DRAWING
NO. 1 AA1142
UNIT ; mm
SHARP
LHF32J02
LH28F320BJE-PTTL90
ZYYWW
xxx
PKG.E?ASE PLANE
jgz
: UJAPANfl
$.??%Wti~~~Q0~---3ttt~
OTES: Marking specificat ion when “JAPAN” is not marked.
!l - ~tkk
i TIN-LEAI: W$ ‘15ZSr3~Wi?#;tlt;ti, r?Jt%dtbC$Who
&;i
ME! TSOP48-P-1220 LEADFINISH ! PLATING NOTE Plastic body dimensions do not include burr
SE
i
of resin.
RAWINGNO. j AA1142
UNIT j mm
J
LHF32J02
SHARP
q
twit
.MEjTSOP48-1220TCM-RH
NOTE
1RAWINCNO. i CV756
SfC
UNIT
;
i mm
LHF32J02
SHARP
Gupplementary
data)
LHF32.JOZ
Recommended mounting
Product name(Package)
._
Packing specification
Mounting method
Reflow soldering
conditions
Measurement point
Storage
conditions
llote
conditions
for two time reflow soldering
.
LH28F320BJE-PTTL90(TSOP48-P-1220)
Tray (Dry packing)
Reflow soldering
(Air)
Peak temperature of 230°C or less.
200°C or over, duration of less than 40 seconds.
Preheat temperature of 125%150”Cduration
of less
than 180 seconds. Temperature increase rate of
l--4Wsecond.
IC package surface
After opening the dry packing, store the ICs in
an environment with a temperature of 5-25°C and
a relative
humidity of 60% or less.
If doing reflow soldering
twice,do
the first
reflow soldering within 72 hours after opening
dry packing and do the second reflow soldering
within 72 hours after the first
reflow soldering.
If the above storage conditions
are not
applicable,
bake it before reflow soldering.
The recommended conditions
are 16-24 hours
at 120°C.
(Heat resistance
tray is used for shipping tray.)
Recommended Reflow
Soldering(Air)
Temperature
Peak
Profile
temperature
lime
(NO. 000323-X21)
SliARP
ADDITIONAL
INFOFtMATION
1 Block Erase Suspend and Resume command
If the time between writing the Block Erase Resume command and writing the Block Erase Suspend command is shorter
than 15ms and both commands are written repeatedly, a longer time is required than standard block erase until the
completion of the operation.
Rev. 0.11
‘I
SHARP
RELATED
DOCUMENT
Document No.
I
~
AP-00 l-SD-E
1 AP-006-R-E
AP-007~SW-E
lNFOFWlATION(‘)
Document Name
1 Flash Memory Family Sofhvare Drivers
I
1 Data Protection Method of SHARP Flash Memory
I
RP#, Vpp Electric Potential Switching Circuit
NOTE :
1. international customers should contact their local SHARP or distribution salesoffice.