SHARP LH28F008SCR-85

PRODUCT SPECIFICATIONS
®
Integrated Circuits Group
LH28F008SCR-L85
Flash Memory
8M (1M ×8)
(Model No.: LHF08CH2)
Spec No.: EL104029B
Issue Date: February 1, 1999
SHARP
LHF08CH2
l Handle
this document carefully for it contains material protected by international
copyright law. Any reproduction, full or in part, of this material is prohibited without the
express written permission of the company.
l When using the products covered herein, please observe
the conditions written herein
and the precautions outlined in the following paragraphs. In no event shall the company
be liable for any damages resulting from failure to strictly adhere to these conditions and
precautions.
(1) The products covered herein
application areas. When using
in Paragraph (Z), even for the
precautions given in Paragraph
in Paragraph (3).
are designed and manufactured for the following
the products covered herein for the equipment listed
following application areas, be sure to observe the
(2). Never use the products for the equipment listed
*Office electronics
l instrumentation and measuring equipment
.Machine tools
@Audiovisual equipment
*Home appliance
l Communication equipment other than for trunk lines
(2) Those contemplating using the products covered herein for the following equipment
which demands hiah reliability, should first contact a sales representative
of the
company and then accept responsibility for incorporating into the design fail-safe
operation, redundancy, and other appropriate measures for ensuring reliability and
safety of the equipment and the overall system.
*Control and safety devices for airplanes, trains, automobiles,
transportation equipment
l Mainframe computers
aTraffic control systems
@Gas leak detectors and automatic cutoff devices
6escue and security equipment
@Other safety devices and safety equipment,etc.
and other
(3) Do not use the products covered herein for the following equipment which demands
extremelv hiqh performance in terms of functionality, reliability, or accuracy.
*Aerospace equipment
*Communications
equipment for trunk lines
*Control equipment for the nuclear power industry
l Medical equipment related to life support, etc.
(4) Please direct all queries and comments
three Paragraphs to a sales representative
*Please direct all queries regarding
of the company.
regarding the interpretation
of the company.
the products covered
of the above
herein to a sales representative
Rev.l.l
SHARP
1
LHFOSCH2
CONTENTS
PAGE
PAGE
I .O INTRODUCTION
...................................................
......................................................
1 .l New Features
1.2 Product Overview.. ..............................................
2.0 PRINCIPLES
OF OPERATION..
...........................
3
3
3
2.1 Data Protection ...................................................
7
7
3.0 BUS OPERATION .................................................
3.1 Read ...................................................................
8
8
3.2 Output Disable ....................................................
3.3 Standby.. .............................................................
..............................................
3.4 Deep Power-Down
8
8
8
3.5 Read Identifier Codes Operation.. .......................
3.6 Write ....................................................................
9
9
1.0 COMMAND DEFINITIONS. ...................................
4.1 Read Array Command.. .....................................
4.2 Read Identifier Codes Command ......................
4.3 Read Status Register Command.. .....................
4.4 Clear Status Register
Command.. .....................
4.5 Block Erase Command.. ....................................
4.6 Byte Write Command ........................................
5.0 DESIGN CONSIDERATIONS
............................. .2?
5.1 Three-Line Output Control ................................ .2?
5.2 RY/BY# and Block Erase, Byte Write and Lock-Bit
25
Configuration Polling ...........................................
5.3 Power Supply Decoupling..
................................
24
5.4 V,, Trace on Printed Circuit Boards.. ............... .2f
24
5.5 v,,, v,,, RP# Transitions .................................
5.6 Power-Up/Down
Protection ................................ 24
5.7 Power
Dissipation
6.0 ELECTRICAL
.............................................
.24
SPECIFICATIONS..
..................... .2E
6.1 Absolute Maximum Ratings ............................... 25
6.2 Operating Conditions .........................................
25
9
6.2.1 Capacitance .................................................
25
6.2.2 AC Input/Output Test Conditions.. ............... .2E
........................................
27
6.2.3 DC Characteristics
12
12
12
6.2.4 AC Characteristics
- Read-Only Operations .2E
6.2.5 AC Characteristics
- Write Operations.. ....... .34
6.2.6 Alternative CE#-Controlled
Writes.. ............. .3E
12
6.2.7 Reset Operations
12
13
4.7 Block Erase Suspend Command.. ..................... 13
4.8 Byte Write Suspend Command.. ....................... 14
4.9 Set Block and Master Lock-Bit Commands.. ..... 14
4.10 Clear Block Lock-Bits Command.. ................... 15
........................................
6.2.8 Block Erase, Byte Write and Lock-Bit
Configuration Performance.. ........................
7.0 ADDITIONAL
7.1 Ordering
8.0 PACKAGE
INFORMATION
............................
Information ..........................................
AND PACKING
SPECIFICATIONS
.3E
.3E
.40
40
..4 1
J
Rev. 1.0
LHF08CH2
2
LH28F008SCR-L85
8-MBIT (1 MB x 8)
SmartVoltage
Flash MEMORY
n SmartVoltage
Technology
- 2.7V(Read-Only),
3.3V or 5V VCC
- 3.3V, 5V or 12V Vpp
n
Enhanced Automated Suspend Options
- Byte Write Suspend to Read
- Block Erase Suspend to Byte Write
- Block Erase Suspend to Read
n
Enhanced Data Protection Features
- Absolute Protection with Vpp=GND
- Flexible Block Locking
- Block Erase/Byte Write Lockout
during Power Transitions
n High-Density
Symmetrically-Blocked
Architecture
- Sixteen 64-Kbyte Erasable Blocks
n
Extended Cycling Capability
- 100,000 Block Erase Cycles
- 1.6 Million Block Erase Cycles/Chip
n Low Power Management
- Deep Power-Down
Mode
- Automatic Power Savings Mode
Decreases ICC in Static Mode
n
Industry-Standard
Packaging
- 40-Lead TSOP (Reverse Bend)
n
ETOXTM* Nonvolatile
I
Automated Byte Write and Block Erase
- Command User Interface
- Status Register
n
CMOS Process
(P-type silicon substrate)
n
I
SRAM-Compatible
Not designed
hardened
n High-Performance
Read Access Time
- 85ns(5V-c0.25V), 90ns(5Vk0.5V),
120ns(3.3V=0.3V),
150ns(2.7V-3.6V)
n Operating Temperature
- 0°C to +7O”C
Write Interface
Flash Technology
or rated as radiation
SHARP’s LH28F008SCFGL85
Flash memory with SmartVoltage technology is a high-density, low-cost, nonvolatile,
,ead/write storage solution for a wide range of applications. Its symmetrically-blocked
architecture, flexible voltage
ind extended cycling provide for highly flexible component suitable for resident flash arrays, SlMMs and memory
:ards. Its enhanced suspend capabilities provide for an ideal solution for code + data storage applications. For
secure code storage applications, such as networking,
where code is either directly executed out of flash or
downloaded to DRAM, the LH28F008SCR-L85
offers three levels of protection: absolute protection with V,, at
;ND, selective hardware block locking, or flexible software
block locking. These alternatives give designers
Jltimate control of their code security needs.
The LH28F008SCR-L85
is manufactured
on SHARP’s
0.38um ETOXTM process technology.
It come in
ndustry-standard
package: the 40-lead TSOP, ideal for board constrained applications. Based on the 28F008SA
architecture, the LH28F008SCR-L85
enables quick and easy upgrades for designs demanding the state-of-the-art.
ETOX is a trademark
of Intel Corporation.
Rev.1.11
SHARf=@
LHF08CH2
1 INTRODUCTION
This
datasheet
contains
LH28F008SCRL85
specifications.
Section 1 provides a flash memory
overview.
Sections 2, 3, 4, and 5 describe
the
memory organization
and functionality.
Section 6
covers electrical specifications.
LH28F008SCRL85
Flash
memory
documentation
also
includes
application
notes and design tools which
are
referenced in Section 7.
SmartVoltage
technology provides a choice of V,,
and V,, combinations, as shown in Table 1, to meet
system performance
and power expectations.
2.7V
Vc, consumes approximately one-fifth the power of
5V Voo. But, 5V Voo provides the highest read
performance. V,, at 3.3V and 5V eliminates the need
for a separate
12V converter,
while V,,=12V
maximizes block erase and byte write performance
In addition to flexible erase and program voltages
the dedicated V,, p in g ives complete data protectior
when V,, I VPPLK.
1.1 New Features
Table 1. V,,
The LH28F008SCRL85
SmartVoltage Flash memory
maintains
backwards-compatibility
with SHARP’s
?8F008SA. Key enhancements
over the 28F008SA
nclude:
*SmartVoltage
Technology
*Enhanced
Suspend Capabilities
*In-System
Block Locking
*Because of new feature support, the two devices
have different device codes. This allows for
software optimization.
l VPPLK
has been lowered from 69
to 1.5V to
support 3.3V and 5V block erase, byte write, and
lock-bit configuration operations. The V,, voltage
transitions to GND is recommended
for designs
that switch V,, off during read operation.
I.2 Product
and VP, Voltage
Combinations
>
NOTE:
1. Block erase, byte write and lock-bit configuratior
operations with Vcoc3.OV are not supported.
30th devices share a compatible
pinout, status
,egister,
and
software
command
set.
These
similarities
enable a clean upgrade
from the
!8F008SA to LH28F008SCR-L85.
When upgrading,
t is important to note the following differences:
*To take advantage of SmartVoltage
allow V,, connection to 3.3V or 5V.
3
technology,
Overview
‘he LH28F008SCR-L85
is a high-performance
8-Mbit
;martVoltage Flash memory organized as 1 Mbyte of
I bits. The 1 Mbyte of data is arranged in sixteen
ICKbyte
blocks which are individually erasable,
jckable, and unlockable in-system.
The memory
lap is shown in Figure 3.
Internal
and
Vcc
automatically
configures
read and write operations.
detection
Circuit4
the device for optimizec
VP,
A Command
User Interface (CUI) serves as the
interface between the system processor and interna
operation of the device. A valid command sequence
written to the CUI initiates device automation. Ar
internal Write State Machine (WSM) automatically
executes the algorithms and timings necessary
for
block erase, byte write, and lock-bit configuratior
operations.
A block erase operation erases one of the device’s
64-Kbyte blocks typically within 0.3 s (5V V,,, 12V
V,,) independent of other blocks. Each block can be
independently
erased 100,000 times (1.6 million
block erases per device). Block erase suspend mode
allows system software to suspend block erase to
read or write data from any other block.
Writing memory data is performed in byte increments
typically within 6 us (5V Voo, 12V VP,). Byte write
suspend mode enables the system to read data or
execute code from any other flash memory array
location.
Rev. 1.2
SHAM=
LHF08CH2
Individual block locking uses a combination of bits,
sixteen block lock-bits and a master lock-bit, to lock
and unlock blocks. Block lock-bits gate block erase
and byte write operations, while the master lock-bit
gates
block
lock-bit
modification.
Lock-bit
configuration
operations
(Set Block Lock-Bit, Set
Master
Lock-Bit,
and
Clear
Block
Lock-Bits
commands) set and cleared lock-bits.
The status register indicates when the WSM’s block
erase, byte write, or lock-bit configuration operation is
finished.
The RY/BY# output gives an additional indicator of
WSM activity by providing both a hardware signal of
status (versus software polling) and status masking
(interrupt masking for background
block erase, for
example). Status polling using RY/BY# minimizes
both CPU overhead and system power consumption.
When low, RY/BY# indicates that the WSM is
oerforming a block erase, byte write, or lock-bit
zonfiguration. RY/BY#-high indicates that the WSM is
?eady for a new command, block erase is suspended
[and byte write is inactive), byte write is suspended,
or the device is in deep power-down
mode.
4
The access time is 85 ns (t,.,,,*,,) over the commercia
temperature
range (0°C to +70X) and Vco supply
voltage range of 4.75V-5.25V. At lower Vco voltages,
the access times are 90 ns (4.5V-5SV),
120 ns
(3.OV-3.6V) and 150 ns (2.7V-3.6V).
The Automatic
Power
Savings
(APS)
feature
substantially
reduces active current when the device
is in static mode (addresses
not switching).
In APS
mode, the typical I,,, current is 1 mA at 5V Vcc.
When CE# and RP# pins are at Voc, the ICC CMOS
standby mode is enabled. When the RP# pin is al
GND, deep power-down
mode is enabled which
minimizes power consumption
and provides write
protection
during reset. A reset time (tPHQV) is
required from RP# switching high until outputs are
valid. Likewise, the device has a wake time (tPHEL)
from RP#-high until writes to the CUI are recognized.
With RP# at GND, the WSM is reset and the status
register is cleared.
The device is available in 40-lead TSOP (Thin Small
Outline Package,
1.2 mm thick, Reverse
Bend).
Pinout is shown in Figure 2.
Rev.1.0
SHARP
5
LHF08CH2
r
CE#
\VE#
(X3
RPb’
..
+ 3*
. . . . . . . . . . fff
Figure
1. Block
Diagram
49
NC
NC
WE#
OE#
RY/BY#
DQ7
DQ6
DQ5
DQ4
vcc
GND
GND
DQ3
A16
A17
Al6
A15
A14
A13
A12
40-LEAD TSOP
STANDARD PINOUT
1Omm x 20mm
TOP VIEW
CE#
vcc
VPP
RP#
41
DQ2
DQl
DQo
40
A9
A6
2
A7
A6
A5
A4
A2
A3
Figure 2. TSOP 40-Lead
Pinout
(Reverse
Bend)
Rev. 1 .ll
Sl-iARP
6
LHF08CH2
r
1
Symbol
A&
Type
9
INPUT
DQc-DQ,
INPUT/
OUTPUT
CE#
INPUT
RP#
INPUT
OE#
INPUT
WE#
INPUT
RY/BY#
OUTPUT
“PP
SUPPLY
“CC
SUPPLY
GND
NC
SUPPLY
Table 2. Pin Descriptions
Name and Function
ADDRESS INPUTS: Inputs for addresses during read and write operations. Addresses
are internally latched during a write cycle.
DATA INPUT/OUTPUTS:
Inputs data and commands durino CUI write cycles; outputs
data during memory array, status register, and identifier code read cycles. Data pins float
to high-impedance when the chip is deselected or outputs are disabled. Data is internally
latched during a write cycle.
CHIP ENABLE: Activates the device’s control logic, input buffers, decoders, and sense
amplifiers. CE#-high deselects the device and reduces power consumption to standby
levels.
RESET/DEEP POWER-DOWN:
Puts the device in deep power-down
mode and resets
internal automation. RP#-high enables normal operation. When driven low, RP# inhibits
write operations which provides data protection during power transitions. Exit from deep
power-down
sets the device to read array mode. RP# at V,, enables setting of the
master lock-bit and enables configuration of block lock-bits when the master lock-bit is
set. RP#=V,,
overrides block lock-bits thereby enabling block erase and byte write
operations to locked memory blocks. Block erase, byte write, or lock-bit configuration
with VIH<RP#cVHH produce spurious results and should not be attempted.
OUTPUT ENABLE: Gates the device’s outputs during a read cycle.
WRITE ENABLE: Controls writes to the CUI and array blocks. Addresses and data are
latched on the rising edge of the WE# pulse.
READY/BUSY#:
Indicates the status of the internal WSM. When low, the WSM is
performing an internal operation (block erase, byte write, or lock-bit configuration).
RY/BY#-high indicates that the WSM is ready for new commands, block erase is
suspended, and byte write is inactive, byte write is suspended, or the device is in deep
power-down
mode. RY/BY# is always active and does not float when the chip is
deselected or data outputs are disabled.
BLOCK ERASE, BYTE WRITE, LOCK-BIT CONFIGURATION
POWER SUPPLY: For
erasing array blocks, writing bytes, or configuring lock-bits. With VppIVpp,k, memory
contents cannot be altered. Block erase, byte write, and lock-bit configuration with an
invalid Vpp (see DC Characteristics)
produce spurious results and should not be
attempted.
DEVICE POWER SUPPLY: Internal detection confioures the device for 2.7V, 3.3” or 5V
operation. To switch from one voltage to another, ramp V,, down to GND and then ramp
Vo, to the new voltage. Do not float any power pins. With VcorV,,,,
all write attempts
to the flash memory are inhibited. Device operations at invalid Vcc voltage (see DC
Characteristics)
produce spurious results and should not be attempted. Block erase, byte
write and lock-bit configuration operations with Vcr.<3.0V are not supported.
GROUND: Do not float any ground pins.
NO CONNECT: Lead is not internal connected; it may be driven or floated.
Rev. 1.0
LHF08CH2
2 PRINCIPLES
7
OF OPERATION
FFFFF
The LH28F008SCR-L85
SmartVoltage Flash memory
includes an on-chip WSM to manage block erase,
byte write, and lock-bit configuration
functions.
It
allows for: 100% TTL-level control inputs, fixed power
supplies during block erasure, byte write, and lock-bit
configuration, and minimal processor
overhead with
RAM-Like interface timings.
After initial device power-up
or return from deep
power-down
mode (see Bus Operations),
the device
defaults to read array mode. Manipulation of external
memory control pins allow array read, standby, and
output disable operations.
Status register and identifier codes can be accessed
through the CUI independent of the V,, voltage. High
voltage on V,, enables successful
block erasure,
byte writing, and lock-bit configuration. All functions
associated
with altering memory
contents-block
erase, byte write, Lock-bit configuration, status, and
identifier codes-are
accessed
via the CUI and
verified through the status register.
Commands
written
using
standard
are
microprocessor
write timings. The CUI contents serve
as input to the WSM, which controls the block erase,
byte write, and lock-bit configuration.
The internal
algorithms are regulated by the WSM, including pulse
repetition, internal verification, and margining of data.
Addresses and data are internally latch during write
cycles. Writing the appropriate
command outputs
array data, accesses the identifier codes, or outputs
status register data.
nterface software that initiates and polls progress of
,lock erase, byte write, and lock-bit configuration can
Ie stored in any block. This code is copied to and
executed from system RAM during flash memory
Jpdates. After successful
completion,
reads are
igain possible via the Read Array command. Block
erase suspend allows system software to suspend a
Ilock erase to read or write data from any other
Ilock. Byte write suspend allows system software to
suspend a byte write to read data from any other
lash memory array location.
I
F0000
EFFFF
EOOOO
DFFFF
DO000
CFFFF
I
coooo
BFFFF
64-Kbyte
Block
131
64-Kbyte
Block
12
BOOW
AFFFF
AOODO
BFFFF
9Qooo
6FFFF
Kmo
7FFFF
70000
BFFFF
60000
SFFFF
I
I
sow0
4FFFF
40000
JFFFF
64-Kbyte Block
81
64-Kbyte Block
7
64-Kbyte Block
61
64-Kbyte Block
5
64-Kbyte
Block
4
64-Kbyte
Block
1
64-Kbyte
Block
0
30000
PFFFF
2oooo
1 FFFF
1oocil
OFFFF
00000
t
’
Hgure
3. Memory
I
Map
2.’1 Data Protection
Depending on the application, the system designer
may choose
to make the V,,
power
supply
switchable
(available
only when
memory
block
erases, byte writes, or lock-bit configurations
are
required)
or hardwired
to VPPHIj2/s. The device
accommodates
either
design
practice
and
encourages
optimization of the processor-memory
interface.
memory
contents
cannot be
When Vp+VppLK,
altered. The CUI, with two-step
block erase, byte
write, or lock-bit configuration command sequences,
provides protection from unwanted operations even
when high voltage is applied to V,,.
All write
functions are disabled when Vcc is below the write
lockout voltage VLKO or when RP# is at V,,. The
device’s block locking capability provides additional
protection from inadvertent code or data alteration by
gating erase and byte write operations.
Rev. 1.0
a
LHFOSCH2
3 BUS OPERATION
consuming
completes.
The local CPU reads and writes flash memory
in-system. All bus cycles to or from the flash memory
conform to standard microprocessor
bus cycles.
3.4
active
power
until
operatior
Deep Power-Down
RP# at V,, initiates the deep power-down
3.1
the
mode.
Read
Information can be read from any block, identifier
codes, or status register independent
of the V,,
voltage. RP# can be at either V,, or V,,.
The first task is to write the appropriate read mode
command (Read Array, Read Identifier Codes, or
Read Status Register) to the CUI. Upon initial device
power-up or after exit from deep power-down
mode,
the device automatically resets to read array mode.
Four control pins dictate the data flow in and out of
the component: CE#, OE#, WE#, and RP#. CE# and
OE# must be driven active to obtain data at the
outputs. CE# is the device selection control, and
when active enables the selected memory device.
OE# is the data output (DQo-DQ,) control and when
active drives the selected memory data onto the I/O
bus. WE# must be at V,, and RP# must be at V,, or
V,,. Figure 15 illustrates a read cycle.
3.2 Output
Disable
With OE# at a logic-high level (V,,), the device
outputs are disabled. Output pins DQc-DQ,
are
3laced in a high-impedance state.
3.3 Standby
ZE# at a logic-high level (V,,) places the device in
standby mode which substantially
reduces device
lower consumption. DQc-DQ, outputs are placed in
3 high-impedance
state independent
of OE#. If
deselected during block erase, byte write, or lock-bit
:onfiguration, the device continues functioning, and
In read modes, RP#-low
deselects
the memory
places output drivers in a high-impedance state ant
turns off all internal circuits. RP# must be held low foi
a minimum of 100 ns. Time tPHQv is required after
return from power-down
until initial memory access
outputs are valid. After this wake-up interval, norma
operation is restored. The CUI is reset to read array
mode and status register is set to 80H.
During
block
erase,
~;~low~rit~~ll
o;botck;;;
configuration
modes,
’
operation.
RY/BY#
remains
low until the resei
operation
is complete.
Memory
contents
being
altered are no longer valid; the data may be partially
erased or written. Time tPHWL is required after RP#
goes to logic-high (VI,) before another command can
be written.
As with any automated device, it is important to
assert RP# during system reset. When the system
comes out of reset, it expects to read from the flash
memory. Automated flash memories provide status
information when accessed during block erase, byte
write, or lock-bit configuration modes. If a CPU reset
occurs with no flash memory reset, proper CPU
initialization may not occur because the flash memory
may be providing status information instead of array
data. SHARP’s flash memories allow proper CPU
initialization following a system reset through the use
of the RP# input. In this application, RP# is controlled
by the same RESET# signal that resets the system
CPU.
Rev. 1.0
LHF08CH2
5 Read Identifier
3.6
Codes Operation
re read identifier codes operation outputs the
anufacturer
code,
device
code,
block
lock
nfiguration codes for each block, and the master
:k configuration
code (see Figure 4). Using the
anufacturer and device codes, the system CPU can
rtomatically
match the device with its proper
gorithms.
The block
lock and master
lock
nfiguration
codes identify locked and unlocked
lcks and master lock-bit setting.
FOO02 1
FOOOI
Block 15 Lock Configuration Code
Reserved for
Future Implementation
Read operation:
When the V,, voltage I V,,,,,
from the status register, identifier codes, or block:
are enabled. Placing VPPHlIti3 on V,,
enable:
successful
block erase, byte write and lock-bi
configuration operations.
Block 1 Lock Configuration Code
10001
10000
The Block Erase command
requires appropriatt
command data and an address within the block to bc
erased.
The Byte Write command
requires
the
command and address of the location to be written
Set Master and Block Lock-Bit commands require the
command and address within the device (Maste
Lock) or block within the device (Block Lock) to bc
locked. The Clear Block Lock-Bits command require:
the command and address within the device.
4 COMMAND
10003
100021
Writing commands
to the CUI enable reading o
device data and identifier codes. They also contra
inspection and clearing of the status register. Wher
VPP=VPPHt/2/3, the CUI additionally controls bloc1
erasure, byte write, and lock-bit configuration.
(Blocks 2 through 14)
1FFFF
10004
Write
The CUI does not occupy an addressable
memog
location. It is written when WE# and CE# are active
The address and data needed to execute a commanc
are latched on the rising edge of WE# or CEf
(whichever goes high first). Standard microprocessor
write timings are used. Figures 16 and 17 illustrate
WE# and CE#-controlled write operations.
Reserved for
Future Implementation
FOOOO
9
Reserved for
Future Implementation
.
1
DEFINITIONS
Device operations
are selected by writing specific
commands
into the CUI. Table 4 defines the.%
commands.
Btock 1
OFFFF
Reserved for
Future Implementation
00004
00003
Master Lock Configuration Code
00002
Block 0 Lock Configuration Code
______---____-----__~-------------~~~~
Device Code
__-------_--------~--------~~~~~~~~~~
Manufacturer Code
00001
‘igure 4. Device Identifier
Code Memory
Map
Rev. 1.0
10
LHF08CH2
Mode
Read
Notes
1,2,3,8
RP#
V$H or
HH
Output Disable
3
‘1,
Or
Standby
3
viH
Or
Deep Power-Down
4
Read Identifier Codes
8
Write
3,6,7,8
VHH
VHH
V,,
vlH
Or
V#
v$+ Or
HH
Table 3. Bus Operations
WE#
CE#
OE#
Address
Vpp
DQIL,
DOUT
RY/BY#
“IL
“IL
“I,
X
X
X
“IL
“I,
“I,
X
X
High Z
X
X
X
X
X
High Z
X
X
X
X
X
High Z
Vnl,
“IL
“IL
“I,
X
See
Figure 4
X
Note 5
‘OH
“IL
“I,
“IL
X
X
DlN
X
“I,
UOTES:
I. Refer to DC Characteristics.
When Vpp<VppLk, memory contents can be read, but not altered.
?. X can be V,, or VI, for control pins and addresses, and VppLk or VppHt/tis for Vpp. See DC Characteristics
for
“PPLK and VPPH1/2/3 vOitages.
3. RY/BY# is VoL when the WSM is executing internal block erase, byte write, or lock-bit configuration algorithms.
It is VOH during when the WSM is not busy, in block erase suspend mode (with byte write inactive), byte write
suspend mode, or deep power-down
mode.
t. RP# at GNDf0.2V ensures the lowest deep power-down
current.
5. See Section 4.2 for read identifier code data.
3. Command writes involving block erase, write, or lock-bit configuration are reliably executed when Vpp=Vpp~t/2/3
Block erase, byte Write?, or lock-bit COnfigUratiOn with vCC<3.0v or VIH<Rf%<VHH-prOdUCe
and “CC=“CC2/3/4
spurious results and should not be attempted.
7. Refer to Table 4 for valid DIN during a write operation.
3. Don’t use the timing both OE# and WE# are VI,.
Rev. 1.0
LHF08CH2
,
Table 4. Command Definitions(g)
First Bus Cycle
Bus Cycles
Req’d.
Notes
Oper(l)
1 Add&*)
1 Data@)
1
1 Write
1
X
1 FFH
Command
Read Array/Reset
Read
Read
Clear
Block
Identifier Codes
Status Register
Status Register
Erase
1Byte Write
I
22
2
1
2
1
2
[
5
1 Write
Write
Write
Write
1 56
1 Write
1
5
Write
Block Erase and Byte Write
co ,.-..A”4
/
Block Eraseand
rlC’3”I
Byte Write
1
/
4
5
/
Write
X
X
X
BA
(
WA
1
X
(
X
90H
70H
50H
20H
40H
or
10H
Second Bus Cycle
1 Oper(l) 1 Addr(*) 1 Data(3)
1
I
Read
Read
1
Write
I
Write
I
IA
X
ID
SRD
BA
DOH
WA
I
WD
I
/I
BOH
(
DOH
(
I Icz
Write
BA
OlH
2
7
Write
BA
60H
Set Block Lock-Bit
Write
X
FlH
Set Master Lock-Bit
2
7
Write
X
60H
Write
X
DOH
2
8
Write
X
60H
Clear Block Lock-Bits
NOTES:
1. BUS operations are defined in Table 3.
2. X=Any valid address within the device.
IA=ldentifier Code Address: see Figure 4.
BA=Address within the block being erased or locked.
WA=Address
of memory location to be written.
3. SRD=Data read from status register. See Table 7 for a description of the status register bits.
WD=Data to be written at location WA. Data is latched on the rising edge of WE# or CE# (whichever goes high
first).
ID=Data read from identifier codes.
4. Following the Read Identifier Codes command, read operations access manufacturer, device, block lock, and
master lock codes. See Section 4.2 for read identifier code data.
5. If the block is locked, RP# must be at V,, to enable block erase or byte write operations. Attempts to issue a
block erase or byte write to a locked block while RP# is VI,.
6. Either 40H or 10H are recognized by the WSM as the byte write setup.
7. If the master lock-bit is set, RP# must be at V,, to set a block lock-bit. RP# must be at V,, to set the master
lock-bit. If the master lock-bit is not set, a block lock-bit can be set while RP# is VI,.
8. If the master lock-bit is set, RP# must be at V,, to clear block lock-bits. The clear block lock-bits operation
simultaneously clears all block lock-bits. If the master lock-bit is not set, the Clear Block Lock-Bits command can
be done while RP# is V,,.
9. Commands other than those shown above are reserved by SHARP for future device implementations
and
should not be used.
Rev. 1 .O
LHF08CH2
12
4.1 Read Array Command
4.3
Upon initial device power-up and after exit from deep
oower-down
mode, the device defaults to read array
node. This operation is also initiated by writing the
Read Array command. The device remains enabled
‘or reads until another command is written. Once the
nternal WSM has started a block erase, byte write or
ock-bit configuration, the device will not recognize
:he Read Array command until the WSM completes
ts operation unless the WSM is suspended via an
Erase Suspend or Byte Write Suspend command.
The Read Array command functions independently of
:he V,, voltage and RP# can be V,, or V,,.
The status register may be read to determine when i
block erase, byte write, or lock-bit configuration is
complete
and whether
the operation
completec
successfully.
It may be read at any time by writing the
Read Status Register command. After writing this
command,
all subsequent
read operations
outpu’
data from the status register until another valic
command is written. The status register contents arc
latched on the falling edge of OE# or CE#, whichevel
occurs. OE# or CE# must toggle to V,, before further
reads to update the status register latch. The Reac
Status Register command functions independently o
the V,, voltage. RP# can be V,, or V,,.
4.2 Read Identifier
Codes Command
The identifier code operation is initiated by writing the
qead Identifier Codes command.
Following
the
:ommand write, read cycles from addresses shown in
‘igure 4 retrieve the manufacturer, device, block lock
:onfiguration and master lock configuration
codes
see Table 5 for identifier code values). To terminate
he operation, write another valid command. Like the
?ead Array command, the Read Identifier Codes
:ommand functions independently of the V,, voltage
%nd RP# can be V,, or V,,. Following the Read
dentifier Codes command, the following information
:an be read:
Table 5. Ideni tifi ier Codes
Code
Manufacture Code
Device Code
Block Lock Configuration
*Block is Unlocked
*Block is Locked
*Reserved for Future Use
Master Lock Configuration
@Device is Unlocked
*Device is Locked
*Reserved for Future Use 1
30TE:
. X selects the specific block lock configuration
code to be read. See Figure 4 for the device
identifier code memory map.
4.4
Read Status Register
Clear Status Register
Command
Command
Status register bits SR.5, SR.4, SR.3, and SR.l are
set to “1 “s by the WSM and can only be reset by the
Clear Status Register command. These bits indicate
various failure conditions (see Table 7). By allowing
system
software
to reset these
bits, several
operations (such as cumulatively erasing or locking
multiple blocks or writing several bytes in sequence)
may be performed. The status register may be polled
to determine if an error occurre during the sequence.
To clear the status register, the Clear
command (50H) is written. It functions
of the applied V,, Voltage. RP# can
This command is not functional during
byte write suspend modes.
4.5
Status Register
independently
be V,, or V,,.
block erase or
Block Erase Command
Erase is executed one block at a time and initiated by
a two-cycle
command. A block erase setup is first
written, followed by an block erase confirm. This
command sequence requires appropriate sequencing
and an address within the block to be erased (erase
block
data
to
FFH).
Block
changes
all
preconditioning,
erase,
and verify are handled
internally by the WSM (invisible to the system). After
the two-cycle
block erase sequence is written, the
device automatically
outputs status register data
when read (see Figure 5). The CPU can detect block
erase completion by analyzing the output data of the
RY/BY# pin or status register bit SR.7.
Rev. 1.0
LHF08CH2
13
When the block erase is complete, status register bit
SR.5 should be checked. If a block erase error is
detected, the status register should be cleared before
system software attempts corrective actions. The CUI
remains in read status register mode until a new
command is issued.
corresponding
block lock-bit be cleared or, if set, tha
RP#=V,,.
If byte write is attempted
when the
corresponding
block lock-bit is set and RP#=V,,
SR.1 and SR.4 will be set to “1”. Byte write
operations
with V,,cRP#cVHH
produce
spurious
results and should not be attempted.
This two-step command sequence of set-up followed
by execution ensures that block contents are not
accidentally erased. An invalid Block Erase command
sequence will result in both status register bits SR.4
and SR.5 being set to “1 ‘I. Also, reliable block erasure
can
only
occur
when
and
vCC=vCC2/314
v,,=v PPi+l2/3*
In the absence of this high voltage,
block contents are protected against erasure. If block
erase is attempted while Vpp&,,,k,
SR.3 and SR.5
will be set to “1”. Successful block erase requires that
the corresponding
block lock-bit be cleared or, if set,
that RP#=V,,.
If block erase is attempted when the
corresponding
block lock-bit is set and RP#=V,,,
SR.l and SR.5 will be set to “1”. Block erase
operations
with V,,cRP#cVH,
produce
spurious
results and should not be attempted.
4.7
4.6 Byte Write Command
Byte write is executed by a two-cycle
command
sequence.
Byte write setup (standard
40H or
alternate 10H) is written, followed by a second write
that specifies the address and data (latched on the
-ising edge of WE#). The WSM then takes over,
controlling the byte write and write verify algorithms
nternally. After the byte write sequence is written, the
device automatically
outputs status register data
Nhen read (see Figure 6). The CPU can detect the
zompletion of the byte write event by analyzing the
?Y/BY# pin or status register bit SR.7.
Nhen byte write is complete, status register bit SR.4
should be checked. If byte write error is detected, the
status register should be cleared. The internal WSM
verify only detects errors for “1 “s that do not
juccessfully
write to “0”s. The CUI remains in read
status register
mode until it receives
another
:ommand.
qeliable
byte
writes
can only
occur
when
Jcc=Vcc2/3,4 and VPrz~VPPr+t/2/3. In the absence of
his high voltage, memory contents are protected
against byte writes. If byte write is attempted while
/+V,,,,,
status register bits SR.3 and SR.4 will be
ret to “1 ‘I. Successful
byte write requires that the
Block Erase Suspend
Command
The
Block
Erase
Suspend
command
allows
block-erase
interruption to read or byte-write data ir
another block of memory. Once the block-erase
process
starts, writing the Block Erase Suspenc
command requests that the WSM suspend the block
erase sequence at a predetermined
point in the
algorithm. The device outputs status register data
when read after the Block Erase Suspend commanc
is written. Polling status register bits SR.7 and SR.E
can determine when the block erase operation has
been suspended (both will be set to “1”). RY/BY# will
also transition to V,,. Specification twHRH2 defines
the block erase suspend latency.
At this point, a Read Array command can be written
to read data from blocks other than that which is
suspended.
A Byte Write command sequence can
also be issued during erase suspend to program data
in other blocks. Using the Byte Write Suspend
command (see Section 4.8), a byte write operation
can also be suspended. During a byte write operation
with block erase suspended, status register bit SR.7
will return to “0” and the RY/BY# output will transition
to V,,. However, SR.6 will remain “1” to indicate
block erase suspend status.
The only other valid commands while block erase is
suspended
are Read Status Register and Block
Erase
Resume.
After a Block Erase
Resume
command is written to the flash memory, the WSM
will continue the block erase process. Status register
bits SR.6 and SR.7 will automatically
clear and
RY/BY# will return to VOL. After the Erase Resume
command is written, the device automatically outputs
status register data when read (see Figure 7). V,,
must remain at V,PH1,2,3 (the same V,, level used
for block erase) while block erase is suspended. RP#
must also remain at V,, or V,, (the same RP# level
used for block erase). Block erase cannot resume
until byte write operations initiated during block erase
suspend have completed.
Rev.
1.0
LHF08CH2
4.8
Byte Write Suspend
Command
The Byte Write Suspend command allows byte write
interruption
to read data in other flash memory
locations. Once the byte write process starts, writing
the Byte Write Suspend command requests that the
WSM suspend
the byte write sequence
at a
predetermined
point in the algorithm. The device
continues to output status register data when read
after the Byte Write Suspend command is written.
Polling status register bits SR.7 and SFi.2 can
determine when the byte write operation has been
suspended (both will be set to “1”). RY/BY# will also
transition to VOH. Specification tWHRHl defines the
byte write suspend latency.
At this point, a Read Array command can be written
to read data from locations other than that which is
suspended.
The only other valid commands
while
byte write is suspended
are Read Status Register
and Byte Write Resume. After Byte Write Resume
command is written to the flash memory, the WSM
will continue the byte write process. Status register
bits SR.2 and SR.7 will automatically
clear and
RY/BY# will return to V,,. After the Byte Write
Resume
command
is
written,
the
device
automatically outputs status register data when read
(see Figure 8). V,, must remain at VPPH1,2,3 (the
same V,, level used for byte write) while in byte write
suspend mode. RP# must also remain at V,, or V,,
(the same RP# level used for byte write).
4.9 Set Block and Master Lock-Bit
Commands
4 flexible block locking and unlocking scheme is
enabled via a combination of block lock-bits and a
master lock-bit. The block lock-bits gate program and
erase operations
while the master lock-bit gates
3lock-lock bit modification. With the master lock-bit
lot set, individual block lock-bits can be set using the
Set Block Lock-Bit
command.
The Set Master
-ock-Bit command, in conjunction with RP#=V,,,
jets the master lock-bit. After the master lock-bit is
jet, subsequent
setting of block lock-bits requires
10th the Set Block Lock-Bit command and V,, on
the RP# pin. See Table 6 for a summary
and software write protection options.
14
of hardwar’
1
Set block lock-bit and master lock-bit are executed b
a two-cycle
command sequence. The set block c
master lock-bit setup along with appropriate block c
device address is written followed by either the SE
block lock-bit confirm (and an address within thl
block to be locked) or the set master lock-bit confirr
(and any device address). The WSM then control
the set lock-bit algorithm. After the sequence
i
written,
the device automatically
outputs
statu
register data when read (see Figure 9). The CPU car
detect the completion of the set lock-bit event b
analyzing the RY/BY# pin output or status register bi
SR.7.
When the set lock-bit operation is complete, statu:
register bit SR.4 should be checked. If an error i:
detected, the status register should be cleared. The
CUI will remain in read status register mode until :
new command is issued.
This two-step
sequence
of set-up followed
b!
execution ensures that lock-bits are not accidentall!
set. An invalid Set Block or Master
Lock-B/
command will result in status register bits SR.4 ant
SR.5 being set to “1”. Also, reliable operations occu
only when Vcc=Vcc2,3,4
and VPP=VPPH,,2,3. In tht
absence of this high voltage, lock-bit contents arc
protected against alteration.
A successful set block lock-bit operation requires tha
the master lock-bit be cleared or, if the maste
lock-bit is set, that RP#=V,,.
If it is attempted wit1
the master lock-bit set and RP#=V,,, SR.l and SR.l
will be set to “1” and the operation will fail. Set block
lock-bit operations
while VIH<RP#cVHH
produce
spurious
results and should not be attempted. P
successful set master lock-bit operation requires tha,
RP#=V,,.
If it is attempted with RP#=V,,, SR.l ant
SR.4 will be set to “1” and the operation will fail. Se
master
lock-bit
operations
with
V,,cRP#cV,,
produce
spurious
results
and should
not be
attempted.
Rev. 1.0
LHF08CH2
l.10
Clear Block Lock-Bits
Command
411set block lock-bits are cleared in parallel via the
Zlear Block Lock-Bits
command. With the master
ock-bit not set, block lock-bits can be cleared using
)nly the Clear Block Lock-Bits
command.
If the
naster lock-bit is set, clearing block lock-bits requires
10th the Clear Block Lock-Bits command and V,, on
he RP# pin. See Table 6 for a summary of hardware
md software write protection options.
Zlear block lock-bits operation is executed by a
wo-cycle command sequence. A clear block lock-bits
setup is first written. After the command is written, the
device automatically
outputs status register data
vhen read (see Figure 10). The CPU can detect
:ompletion of the clear block lock-bits event by
analyzing the RYIBY# Pin output or status register bit
SR.7.
Yhen the operation is complete, status register bit
jR.5 should be checked. If a clear block lock-bit error
s detected, the status register should be cleared.
‘he CUI will remain in read status register mode until
nother command is issued.
Operation
Block Erase or
Byte Write
1 Master
1 Lock-Bit
X
Set Block
Lock-Bit
Set Master
Lock-Bit
Clear Block
Lock-Bits
0
1
1
X
0
1
15
This two-step
sequence
of set-up followed
b\
execution
ensures
that block lock-bits
are no
accidentally cleared. An invalid Clear Block Lock-Bit:
command sequence will result in status register bit:
SR.4 and SR.5 being set to “1”. Also, a reliable clea
block lock-bits
operation
can only occur wher
Vcc=Vcc2/3,4
and VPP=VPPHI12/s. If a clear bloc1
lock-bits operation is attempted while V,,rV,,,,
SR.3 and SR.5 will be set to “1”. In the absence o
this high voltage, the block lock-bits content arc
protected against alteration. A successful clear bloc1
lock-bits operation requires that the master lock-bit i:
not set or, if the master lock-bit is set, that RP#=V,,
If it is attempted with the master lock-bit set ant
RP#=V,,,
SR.1 and SR.5 will be set to “1” and the
operation will fail. A clear block lock-bits operatior
with V,,cRP#cV,,
p reduce spurious
results ant
should not be attempted.
If a clear block lock-bits operation is aborted due tc
V,, or Vc, transitioning out of valid range or RP#
active transition, block lock-bit values are left in ar
undetermined state. A repeat of clear block lock-bits
is required to initialize block lock-bit contents tc
known values. Once the master lock-bit is set, ii
cannot be cleared.
Table 6. Write Protection
Alternatives
1 Block
1
1L
Effect
Block Erase and Byte Write Enabled
Block is Locked. Block Erase and Byte Write Disabled
1 Block Lock-Bit Override. Block Erase and Bvte Write
I
\I
“HH
Enabled
X
VI,, or VWH
Set Block Lock-Bit Enabled
X
V,H
Master Lock-Bit is Set. Set Block Lock-Bit Disabled
VHH
1 Master Lock-Bit Override. Set Block Lock-Bit Ena bled
1
X
V,H
1 Set Master Lock-Bit Disabled
V
Set Master Lock-Bit Enabled
X
V 0rV
Clear Block Lock-Bits Enabled
X
V
Master Lock-Bit is Set. Clear Block Lock-Bits Disabled
Master Lock-Bit Override. Clear Block Lock-Bits
\I
“HH
1 Enabled
B
Rev. 1 .O
SHARP
LHF08CH2
WSMS
/
ESS
7
1
ECLBS
6
Table 7. Status
1 BWSLBS
5
4
Register Definition
1 VPPS
1 BWSS
3
2
1
DPS
R
1
0
NOTES:
SR.7 = WRITE
1 = Ready
0 = Busy
STATE MACHINE
STATUS
Check RY/BY# or SR.7 to determine block erase, byte
write, or lock-bit configuration completion.
SR.6-0 are invalid while SR.7=“0”.
SR.6 = ERASE SUSPEND STATUS
1 = Block Erase Suspended
0 = Block Erase in Progress/Completed
If both SR.5 and SR.4 are “1”s after a block erase or
lock-bit configuration attempt, an improper command
sequence was entered.
SR.5 = ERASE AND CLEAR LOCK-BITS STATUS
1 = Error in Block Erasure or Clear Lock-Bits
0 = Successful Block Erase or Clear Lock-Bits
SR.3 does not provide a continuous indication of V,,
level. The WSM interrogates and indicates the V,, level
only after Block Erase, Byte Write, Set Block/Master
Lock-Bit, or Clear Block Lock-Bits command sequences.
SR.3 is not guaranteed to reports accurate feedback
only
when V,,#V,,,,,~,,.
SR.4 = BYTE WRITE AND SET LOCK-BIT STATUS
1 = Error in Byte Write or Set Master/Block Lock-Bit
0 = Successful Byte Write or Set Master/Block
Lock-Bit
SR.3 = V,, STATUS
1 = V,, Low Detect, Operation
O=V,,OK
Abort
SR.2 = BYTE WRITE SUSPEND STATUS
1 = Byte Write Suspended
0 = Byte Write in Progress/Completed
SR.l = DEVICE PROTECT STATUS
1 = Master Lock-Bit, Block Lock-Bit and/or RP# Lock
Detected, Operation Abort
0 = Unlock
SR.0 = RESERVED
FOR FUTURE
ENHANCEMENTS
SR.l does not provide a continuous indication of master
and block lock-bit values. The WSM interrogates the
master lock-bit, block lock-bit, and RP# only after Block
Erase, Byte Write, or Lock-Bit configuration command
sequences. It informs the system, depending on the
attempted operation, if the block lock-bit is set, master
lock-bit is set, and/or RP# is not V,,. Reading the block
lock and master lock configuration codes after writing
the Read Identifier Codes command indicates master
and block lock-bit status.
SR.0 is reserved for future use and should be masked
out when polling the status register.
LHF08CH2
Comments
Command
I
/
write
1
EraseSetup
1 Data=20H
Addr=Wlthin
Block to be Erased
write
Data-DOH
Addr=Withm
Block to be Erased
Read
Status Rqster
Data
Check SR.7
,=WSM Ready
O=WSM Busy
Standby
Full status check can be done after each block erase or after a sequence
block erasures.
Wnte FFH after the last operation to place device in read array mode.
of
Check if Desired
FULLSTATUSCHECKPROCEDURE
BUS
Operation
Command
Comments
Standby
Check SR.3
l=Vpp Error Detect
Standby
Check SR. 1
l=Device Protect Detect
RP#=V,,+Block
Lock-Bit is Set
Only required for systems
implementing
lock-bit configuration
Check SR.4,5
Both t=Command
Sequence
Error
Check SR.5
l=Block Erase Error
;R.5,SR.4.SR.3
and SR., are only cleared by the Clear Status
Register Command
in casas where multiple blocks are erased
before full status is checked.
error is detected. clear the Status Register before attempting
retry or other error recovery.
Block Erase Error
Block Erase Successful
Figure 5. Automated
Block
Erase Flowchart
Rev. 1.0
SHARI=
18
LHF08CH2
Command
Suspend Byte
write Loop
write
Setup Byte Write
Wnte
Byte Wnte
Comments
DatedOH
AddkLwabon
to Be Wlitten
Data=Data to Be Written
Addr=Lccation
to Be Written
Read
Status Register
Standby
Check SR.7
l=WSM Ready
O=WSM Busy
Data
Repeat for subsequent
byte writes.
SR full status check can be done after each byte write. or after a sequence
byte writes.
Wnte FFH after the last byte write operation to place device III
read array mode.
FULL STATUS
CHECK
of
PROCEDURE
Command
Device
Comments
Standby
Check SR.3
1+,x
Error Detect
Standby
Check SR. 1
l=Devse
Protect Detect
RP#=VIH,Block
Lock-Bit is Set
Only required for systems
Implementing
lock-btt configuration
Standby
Check SR.4
l=Data Wnte Error
Protect Error
57.4.SR.3 and SR. 7 are only cleared by the Clear Status Regtster
command in cases where multiple locations are written before
full status is checked.
I f error is detected, clear the Status Register before attempting
retry or other error reco”ely.
Byte Wnte Successful
Figure 6. Automated
Byte Write Flowchart
Rev. 1 .O
LHF08CH2
start
Bus
Operation
Comments
Command
I
I
Write BOH
Status Register
Check 533.7
1 =WSM Reacty
o=WSM Busy
Check SR.6
l=Block Erase Suspended
O=Block Erase Completed
write
Figure 7. Block
Erase Suspend/Resume
El-&%
Resume
Data=DOH
Addr=X
Flowchart
Rev. 1.0
LHF08CH2
r
Bus
Operation
write
Command
I
Byte Write
Suspend
status
Regster
Data
Read
SR.7=
i:t
Data=BOH
Addr=X
Addr=X
standby
Check SR.7
1 =WSM Ready
O=WSM Busy
standby
Check SR.2
l=Byte Write Suspended
o=Byte Write Completed
0
1
Read Army
Figure 8. Byte Write Suspend/Resume
Data=FFH
Addr=X
Flowchart
Rev. 1.0
SHARP
21
LHF08CH2
Bus
Operation
write
set
Block/Master
Lock-Bit Sehrp
write
Block or Master
set
Write OIHIFIH,
Lock-Bit
CHECK
Confirm
Data=OlH(Block),
FlH(Master)
Addr=Blcck Address(Block),
Device Address(Master)
Read
Status Register
Standby
Check SR.7
l=WSM Ready
O=WSM Busy
Data
PROCEDURE
Read Status Register
Data(See Above)
BUS
Operation
Check SR.3
t=VpP Error Detect
Check SR.1
I=Dewce Protect Detect
RP#+,
(Set Master Lock-Blt Operation)
Standby
Device
RP#=VIH, Master Lock-Bit is Set
(Set Block Lock-Blt Operation)
Protect Error
Set Lock-Bit
Error
Comment3
Command
Standby
Set Lock-Bit
Data=6OH
Addr=Block Address(Block),
Dewca Address(Master)
Repeat for subsequent
lock-bit set operations.
Full status check can be done after each lock-btt set oper’dtion
or after a sequence of lock-bit set operations.
Wnte FFH after the last lock-bit set operation to place device I”
read army mode.
Check If Desired
FULL STATUS
Commenb
Command
Standby
Check SR.4,5
Both l=Command
Sequence Error
Standby
Check SR.4
l=Set Lock-Bit
Error
SR.5.SR.4,SR.3
and SR.1 are only cleared by the Clear Status
Register command I” cases where multiple lock-bits are set before
full status is checked.
If error IS detected, clear the Status Register before attempting
retry or other error recovery.
Successful
Figure 9. Set Block
and Master
Lock-Bit
Flowchart
Rev. 1.0
22
LHF08CH2
Start
BUS
Operation
write 60H
x
0
SR.7=
Command
Comments
WI-Its
Clear Block
Lock-Bits Setup
Data=M)H
Addr=X
Write
Clear Block
Lock-Bits Confirm
Data=DOH
Addr=X
Read
Status Register
Standby
Check SA.7
l=WSM Ready
O=WSM Busy
\ Nrite FFH after the Clear Block Lock-Bits
Fhate device in read array mode.
operation
Data
to
1
+
Check If Desired
FULL STATUS
CHECK
PROCEDURE
BUS
Operation
Device
Protect Error
Command
Comments
Standby
Check SR.3
l=Vpp Error Detect
Standby
Check SR. 1
MJevice
Pmtect Detect
RP#=V,H, Master Lock-Bit
Standby
Check SR.4,5
Both l=Command
Sequence
Error
Standby
Check SR.5
l&tear
Block Lock-Bits
is Set
Error
SR.5.SR.4.SR.3
and SR. 1 are only cleared by the Clear Status
Register command.
f error is detected, clear the Status Register before attempting
retry or other error recovery.
Figure
10. Clear Block
Lock-Bits
Flowchart
Rev. 1.0
LHFOSCH2
23
1
5 DESIGN CONSIDERATIONS
5.1 Three-Line
RY/BY# is also VOH when the device is in block eras
suspend (with byte write inactive), byte write suspenc
or deep power-down
modes.
Output Control
The device will often be used in large memory arrays.
SHARP
provides
three
control
inputs
to
accommodate
multiple
memory
connections.
Three-line control provides for:
a. Lowest possible memory power dissipation.
b. Complete assurance that data bus contention
not occur.
will
To use these control inputs efficiently, an address
decoder should enable CE# while OE# should be
connected to all memory devices and the system’s
READ# control line. This assures that only selected
memory devices
have
active
outputs
while
deselected memory devices are in standby mode.
RP#
should
be connected
to the
system
POWERGOOD
signal to prevent unintended writes
during system
power transitions.
POWERGOOD
should also toggle during system reset.
5.3
Power Supply Decoupling
Flash memory power switching characteristics
require
careful device decoupling.
System designers
arc
interested in three supply current issues; standb
current levels, active current levels and transien
peaks produced by falling and rising edges of CEI
and OE#. Transient current magnitudes depend OI
the device outputs’ capacitive and inductive loading
Two-line
control and proper decoupling capacito
selection will suppress transient voltage peaks. Eacl
device should have a 0.1 uF ceramic capacito
connected between its Voo and GND and between it:
V,, and GND. These high-frequency, low inductance
capacitors should be placed as close as possible tc
package leads. Additionally, for every eight devices
a 4.7 uF electrolytic capacitor should be placed at the
array’s power supply connection between V,, ant
GND. The bulk capacitor will overcome
voltage
slumps caused by PC board trace inductance.
5.2 RY/BY# and Block Erase, Byte Write,
and Lock-Bit Configuration
Polling
5.4
RY/BY# is a full CMOS output that provides a
lardware method of detecting block erase, byte write
snd lock-bit configuration completion. It transitions
ow after block erase,
byte write,
or lock-bit
:onfiguration commands and returns to V,, when
he WSM
has finished
executing
the internal
algorithm.
Updating flash memories that reside in the targe
system
requires
that the printed circuit boarc
designer pay attention to the V,, Power supply trace
The V,, pin supplies the memory cell current for by&
writing and block erasing. Use similar trace width:
and layout considerations
given to the Voc powel
bus. Adequate V,, supply traces and decoupling wil
decrease V,, voltage spikes and overshoots.
Vpp Trace on Printed Circuit
Boards
3Y/BY# can be connected to an interrupt input of the
;yStf?m
CPU or controller. It is active at all times.
Rev. 1.0
LHF08CH2
5.5 Vcc, Vpp, RP# Transitions
Block erase, byte write and lock-bit configuration are
not guaranteed if V,n falls outside of a valid V,,,,,,,
range, Vcc falls outside of a valid Vcc2,3,4 range, or
RP#&,,,
or V,,. If V,, error is detected, status
register bit SR.3 is set to “1” along with SR.4 or SR.5,
depending
on the attempted
operation.
If RP#
transitions to V,, during block erase, byte write, or
lock-bit configuration, RY/BY# will remain low until
the reset operation is complete. Then, the operation
will abort and the device will enter deep power-down.
The aborted operation may leave data partially
altered. Therefore, the command sequence must be
repeated after normal operation is restored. Device
power-off or RP# transitions to V,, clear the status
register.
The CUI latches commands
issued by system
software and is not altered by V,, or CE# transitions
or WSM actions. Its state is read array mode upon
sower-up, after exit from deep power-down
or after
Vcc transitions below VLKO.
After
3ven
nust
Array
array
block erase, byte write, or lock-bit configuration,
after V,, transitions down to VpPLK, the CUI
be placed in read array mode via the Read
command if subsequent access to the memory
is desired.
5.6 Power-Up/Down
Protection
The device is designed to offer
3ccidental block erasure, byte
:onfiguration
during
power
lower-up, the device is indifferent
protection against
writing, or lock-bit
transitions.
Upon
as to which power
24
supply (V,, or Vcc) powers-up first. Internal circuitr
resets the CUI to read array mode at power-up.
1
A system
designer must guard against spuriou:
writes for Vcc voltages above VLKO when V,, i!
active. Since both WE# and CE# must be low for i
command write, driving either to VI, will inhibit writes
The CUl’s two-step command sequence architecturt
provides
added level of protection
against datr
alteration.
In-system block lock and unlock capability prevent:
inadvertent data alteration. The device is disablec
while RP#=V,, regardless of its control inputs state. ’
5.7
Power Dissipation
When designing portable systems, designers
mus
consider battery power consumption not only durin!
device operation, but also for data retention during
system
idle time. Flash memory’s
nonvolatilih
increases usable battery life because data is retainec
when system power is removed.
In addition,
deep power-down
mode ensure:
extremely low power consumption even when systen
power is applied. For example, portable computing
products and other power sensitive applications tha
use an array of devices for solid-state storage car
consume negligible power by lowering RP# to VI,
standby or sleep modes. If access is again needed
the devices can be read following the tpHav ant
tPHWL wake-up
cycles required after RP# is firs
raised to V,,. See AC CharacteristicsRead Only
and Write Operations and Figures 15, 16 and 17 fol
more information.
Rev. 1.0
LHF08CH2
6 ELECTRICAL
6.1
Absolute
SPECIFICATIONS
Maximum
Ratings*
Operating Temperature
During Read, Block Erase, Byte Write
and Lock-Bit Configuration . . .. . .. .. ..O”C to +7O”C(1)
Temperature under Bias . . . .. . .. . .. .. . . -10°C to +8O”C
Storage Temperature
. . .. . .. . .. .. . . .. . .. . .. .. -65°C to +125”C
Voltage On Any Pin
(except Vcc, VP,, and RP#) . . .._..-2.OV to +7.OV@)
V,,
Supply Voltage . . .. .. . . . .. .. . .. . .. .. . . .. . -2.ov to +7.0@)
V,, Update Voltage during
Block Erase, Byte Write and
Lock-Bit Configuration .. .. .. .. . .. -2.OV to +14.OV(2J)
RP# Voltage with Respect to
GND during Lock-Bit
Configuration Operations .. .. . . -2.OV to +14.0V(2J)
25
*WARNING:
Stressing
the device beyond
the
“Absolute Maximum Ratings” may cause permanent
damage. These are stress ratings only. Operation
“Operating
Conditions ” is
not
beyond
the
recommended
and extended exposure beyond the
“Operating Conditions” may affect device reliability.
NOTES:
1. Operating
temperature
is
for
commercial
temperature product defined by this specification.
2. All specified voltages are with respect to GND.
Minimum DC voltage is -0.5V on input/output pins
and -0.2V on V,,
and V,,
pins. During
transitions, this level may undershoot to -2.OV for
Maximum
DC voltage
on
periods
<20ns.
input/output pins and Voc is Vcc+O.SI
which,
during transitions, may overshoot to Vcc+2.OV for
periods c20ns.
3. Maximum DC voltage on V,, and RP# may
overshoot to +14.OV for periods <20ns.
4. Output shorted for no more than one second. No
more than one output shorted at a time.
Output Short Circuit Current . . .. .. . . .. . .. . .. .. . .. .. . 1 00mAc4)
6.2
Operating
Conditions
Temperature
and Vcc Operating Conditions
Symbol 1
Parameter
1 Notes
Min.
1 Max.
1 Unit
1
Test Condition
T,
( Operating Temperature
1 +70
I
“C
I Ambient Temperature
0
Van,
Vcc Supply Voltage (2.7V-3.6V)
1
2.7
3.6
V
Vr-c,
Vnn Supply Voltage (3.3V+O.3V)
V
3.0
3.6
Voo2
Vnr. Supply Voltage (5V+O.25V)
4.75
5.25
V
V,,
Vnn Supply Voltage (5V+O5V)
5.50
V
4.50
NOTE:
1. Block erase, byte write and lock-bit configuration operations with Vo,<3.OV should not be attempted.
6.2.1
CAPACITANCE(‘)
Symbol
C,N
Ca,T
NOTE:
1. Sampled,
Parameter
Input Capacitance
Output Capacitance
T,=+25”C,
Typ.
6
8
f=l MHz
Max.
8
12
Unit
pF
pF
Condition
v,,=o.ov
v(-y ,J-=O.OV
not 100% tested.
Rev. 1.11
LHF08CH2
1.2.2 AC INPUT/OUTPUT
TEST CONDITIONS
1:;
-T--,j(Z2~+--Y
AC test inputs are driven at 2.7V for a Logic “1” and O.OV for a Logic
Input rise and fall times (10% to 90%) <IO ns.
Figure 11. Transient
Input/Output
Reference
“0.” input timing
Waveform
begins,
and output
timing
ends, at 1.35V.
for Vcc=2.7V-3.6V
~~~~;~~~
AC test inputs are driven at 3.OV for a Logic “1” and O.OV for a Logic
Input rise and fall times (10% to 90%) <IO ns.
Figure 12. Transient
“0.” Input timing
begins,
Input/Output
Reference Waveform
for VcC=3.3V*0.3V
(High Speed Testing Configuration)
and output
timing ends,
and VcC=5V+0.25V
AC test inputs are driven at VOH (2.4 VTTL) for a Logic “1” and V~L (0.45 V~L) for a Logic “0.” Input timing begins
(2.0 VmL) and VIL (0.8 V&.
Output timing ends at VIH and VIL. Input rise and fall times (10% to 90%) ~10 ns.
Figure 13. Transient
Input/Output
Reference Waveform
(Standard Testing Configuration)
Test Confi
at 1.W.
at VIH
for Vcc=SV*O.SV
uration
Ca acitance
Loadin
Value
1
DEVICE
UNDER
TEST
0
OUT
CL Includes Jig
Capacitance
Figure
14. Transient Equivalent
Load Circuit
Testing
Rev. 1.2
LHF08CH2
27
L2.3 DC CHARACTERISTICS
Sym.
‘Li
Parameter
Input Load Current
‘LO
Output Leakage
‘cc,
V,,
Current
Standby Current
Votes
1
DC Ch -alracteristics
Vcc=2.7V
Vcr
Typ. 1 Max. Lre,
I
kO.5
1
1,3,6
Uni
IJA
kO.5
CIA
*
20
100
20
0.1
2
0.2
=lx
100
25
100
IJA
mA
I
CCD
CCR
Vcc Deep Power-Down
Current
dcc Read Current
1
PA
133
-s--7
7
ccw
CCE
:cws
lxxs.
‘PS
TEL...‘PD
‘PW
ticc Byte Write or
Set Lock-Bit Current
I,7
dcc Block Erase or
1,7
Zlear Block Lock-Bits
Zurrent
I,, Byte Write or Block
v--irase Suspend Current
Ipp Standby or Read
hrrent
I,, Deep Power-Down
hrrent
fpp Byte Write or Set
~
.ock-Bit Current
‘PE
Ipp Block Erase or
Zlear Lock-Bit Current
‘PWS
9xS-
Ipp Byte Write or Block
:rase Suspend Current
18
8
-
-
_+2
10
*15
200
A2
10
0.1
5
0.1
-
1
-’
-
l-l12
17
35
mA
18
20
50
mA
-
mA
mA
mA
mA
mA
mA
1 10
mA
CE#=V,,,
&
CIA
IJA
vpp_<v,,
\Ipp>Vcc.
mA
mA
mA
mA
mA
mA
Vpp=3.3V~0.3V
dpp=5.0V+0.5V
Vpp=12.0V+0.6V
vpp=3.3v~o.3v
vpp=5.0v+o.5v
VP,=1 2.OV&O.6V
I
17
I
6
1
40
40
15
20
20
15
10
Vcc=VccMax.
CE#=RP#=V,,.,
RP#=GND*0.2V
b, ,,(RY/BY#)=OmA
CMOS Inputs
Vcc=VCCMax.
CE#=GND
f=5MHz(3.3V, 2.7V),
8MHz(5V)
In, ,T=OmA
TTL Inputs
V,,=V,,Max.
CE#=GND
f=5MHz(3.3V,
2.7V),
8MHz(5V)
In, ,T=OmA
vDo=3.3v*o.3V
200
_
I
-
I
1
-
-
10
40
15
20
15
RP#=GND*0.2V
200
Rev. 1.2
SHARP
LHFOBCH2
4,
Parameter
Input Low Voltage
Input High Voltage
Notes
7
7
VOL
Output Low Voltage
3,7
Sym.
V,,
28
Continued
DCC :h ,aracteristics
&-.& =; !.7V
Vcc=3.3V
1 Vc.,dV
Min. Max.
Min.
Max.
Min.
Max.
-0.5
0.8
-0.5
0.8
-0.5
0.8
Vcc
VCC
2.0
+0.5
2.0
vcc
2.0
+0.5
+0.5
0.45
Unit
V
V
V
I
VoHl
Output High Voltage
V-J
3,7
Output High Voltage
(CMOS)
3,7
2.4
V
I
VOH2
V,,r+
V,,Hs
V, kr,
vHH
Lock-Bit Operations
V,, during Byte Write,
Block Erase or
Lock-Bit Operations
V,, during Byte Write,
Block Erase or
Lock-Bit Operations
Vcr: Lockout Voltage
f?P# Unlock Voltage
0.85
Yc.cL
vcc
-0.4
1 0.85
I
I
1 0.85
V
1.5
V
-
-
V
-
5.5
V
-
12.6
V
-
Vcc=VccMin.
IO ,=5.8mA(Vcc=5V),
loL=2.0mA
(Vnn=3.3V, 2.7V)
Vcc=VcoMin.
loH=-2.%lA(vCc=5v),
lo,=-2.0mA(vcc=3.3v)
In,,=-1 .5mA(Vr.,=2.7V)
V
2.0
8,9
Test
Conditions
In!+=-1 OOuA
V
-
j 11.4 / 12.6 / 11.4
12.6
V
Set master lock-bit
Override master and
block lock-bit
IOTES:
. All currents are in RMS unless otherwise noted. Typical values at nominal Voc voltage and T,=+25”C. These
currents are valid for all product versions (packages and speeds).
If read or byte written while in erase suspend mode,
. ‘CCWS and ‘CCES are specified with the device de-selected.
the device’s current draw is the sum of lccws or IocEs and lCCR or I,,,,
respectively.
‘. Includes RY/BY#.
. Block erases, byte writes, and lock-bit configurations are inhibited when V&J,,,,,
and not guaranteed in the
range between VppLk(max.) and VppHt(min.), between Vnr+n(max.)
and Vpp&min.),
between Vpp&max.)
and VppHs(min.), and above VppHs(max.).
. Automatic Power Savings (APS) reduces typical I,,, to 1mA at 5V Vcc and 3mA at 2.7V and 3.3V Voc in static
operation.
. CMOS inputs are either Vco- +0.2V or GNDk0.2V. TTL inputs are either V,, or Vi,.
. Sampled, not 100% tested.
. Master lock-bit set operations are inhibited when RP#=V,,. Block lock-bit configuration operations are inhibited
when the master lock-bit is set and RP#=VrH. Block erases and byte writes are inhibited when the corresponding
block-lock bit is set and RP#=VrH. Block erase, byte write, and lock-bit configuration operations are not
guaranteed with Vcc <3.OV or VrH<RP#<VHH and should not be attempted.
. RP# connection to a VHH supply is allowed for a maximum cumulative period of 80 hours.
Rev. 1.2
29
LHFOSCH2
6.2.4
AC CHARACTERISTICS
- READ-ONLY
OPERATIONS(‘)
I
Vc,,=2.7V-3.6V,
Sym.
tr,, nx
GHC)7
LH
Versiond4)
Parameter
1
1 Notes
OE# to Outr
OE# High to Output in High Z
Output Hold from Address, CE# ot
Whichever Occurs First
NOTE:
See 5.OV V,,
Sym.
tJ”A”
ta”n”
tF, (-Jv
tpwnv
t
T,pO”C to +7O”C
3
1
LH28F008SGL150
Max.
Min.
.--
1
Unit
1
11
ns
0
Read-Only Operations for notes 1 through 4.
Vc:,=3.3V+0.3V,
Versiond4)
Parameter
Tg -0°C to +7O”C
Read Cyc& Time
Addre:
1 Notes
. ..------SC-L,20
LH28FO08
Min.
120
Max.
Unit
ns
ns
1RP# Hiqh to Output Delay
NOTE:
See 5.OV V,,
Read-Only Operations for notes 1 through 4.
Rev. 1.0
SI-IARP
LHF08CH2
Vcc=5Vdl.5V,
5VkO.25V,
Vcc=5V+0.25Vj
Sym.
t*“n”
t*“n”
tpHn”
k, nx
30
T,=O”C to +70X
LH28FO08Sc-L=(5)
1
I
Read Cycle
Address to C
CE# to Outp
RP# High to
OE# to Outp
CE# to Outp
CE# High to VUhc/UL ,,,
OE#to Output in Low Z
Output Hold from Address,
Change, Whichever Occurs
NOTES:
1. See AC Input/Output Reference Waveform for maximum allowable input slew rate.
2. OE# may be delayed up to tELQV-tGLQv after the falling edge of CE# without impact on tELQv.
3. Sampled, not 100% tested.
4. See Ordering Information for device speeds (valid operational combinations).
5. See Transient Input/Output Reference Waveform and Transient Equivalent Testing Load Circuit (High Speed
Configuration) for testing characteristics.
6. See Transient Input/Output Reference Waveform and Transient Equivalent Testing Load Circuit (Standard
Configuration) for testing characteristics.
Rev. 1.11
SHARP
31
LHF08CH2
Device
Address Selection
Data Valid
t
Address
.I.,....,,
Stable
r
VIH
CE#(E)
VIL
c
VIH
OE#(G)
WL
VIH
WE#(W)
VIL
tOH,--+
,1,,,,,,,,
VOH
DATA(D/Q)
(DQo-DQ7)
VOL
vcc
VIH
RP#(P)
VIL
Figure
15. AC Waveform
for Read Operations
L
Rev. 1.0
SHARP
LHF08CH2
6.2.5
AC CHARACTERISTICS
- WRITE OPERAATION
Vc.=2.7V-3.6V,
TA=O”C to +7O”C
Versiond5)
Parameter
tA”A”
Write Cycle Time
RP# High Recovery
tPl-!Wl
NOTE:
See 5.OV V,,
Svm.
t d\,A\l
tpuw,
fF, w,
tWl
WH
&
tvpWCl
t*,,-,,,,,,
tnvw,,
twwnx
tWHAX
WE#-Controlled
to WE# Going Low
2
Unit
ns
IJS
Writes for notes 1 through 5.
Vcc=3.3V+0.3V,
Versiond5)
Parameter
AC Characteristics
LH28F008SGL150
Min.
1
Max.
150
1
Notes
I
1Write Cvcle Time
RP# High Recovery tcI WE# Going Low
CE# Setup to WE# Going Low
WE#P- ulse
-- Width
~~
1RP# VHH Setup to WE# Going High
1Vpp Setup to WE!# Going High
[ Address Setup to WE # Going High
[ Data Setup to WE# G oing High
1 Data Hold fron I WE# High
) Address Hold From WE# Hiah
CE# Hold from VVE# High
WE# Pulse Width I High
WE# High to RY/ BY# Going Low
Write Recovery before Read
Vpp Hold from Valid SRD, RY/BY# High
RP# V,,,, Hold from Valid SRD, RY/BY# High
tWHFH
bacHw,
twHR,
bur,,
tn”v,
tn”pH
IOTE:
;ee 5V V,,
32
- Write Operations
T‘,=O”C to +70X
1 Notes
2
2
2
3
3
2,4
2,4
1
LH28F008SC-L120
Min.
Max.
120
1
0
70
100
100
50
50
5
5
0
25
100
0
0
0
Unit
--..ns
p3
ns
“C
I._
ns
ns
ns
ns
ns
Inc
*u
ns
ns
ns
ns
ns
ns
for Notes 1 through 5.
Rev. 1.2
LHFOSCH2
UOTES:
I. Read timing characteristics
during block erase, byte write and lock-bit configuration operations are the same as
during read-onry operations. Refer to AC Characteristics
for read-only operations.
!. Sampled, not 100% tested.
3. Refer to Table 4 for valid A,, and D,, for block erase, byte write, or lock-bit configuration.
1. V,, should be held at VPPH1,2,3 ( and if necessary RP# should be held at V,,) until determination of block erase,
byte write, or lock-bit configuration success (SR.1/3/4/5=0).
5. See Ordering Information for device speeds (valid operational combinations).
5. See Transient Input/Output Reference Waveform and Transient Equivalent Testing Load Circuit (High Seed
Configuration) for testing characteristics.
7. See Transient Input/Output Reference Waveform and Transient Equivalent Testing Load Circuit (Standard
Configuration) for testing characteristics.
Rev. 1.2
SHARP
LHFOBCH2
1
rcs-----
2
3
4
5
6
VIH
ADDRESSES(A)
CE#(E)
tWHGL
VIH
OE#(G)
VIL
VIH
WE#(W)
VIL
VIH
DATA( D/Q)
VOH
RY/BY#(R)
RP#(P)
NOTES:
1. Vcc power-up
2. Write block
3. Write block
4. Automated
5. Read status
6. Write Read
and standby.
erase or byte write setup.
erase confirm or valid address
erase or program delay.
register data.
Array command.
Figure
and data.
16. AC Waveform
for WE#-Controlled
Write Operations
Rev. 1 .O
35
LHF08CH2
6.2.6
ALTERNATIVE
CE#-CONTROLLED
WRITES(‘)
Vc:,=2.7V-3.6V,
Versiond5)
Parameter
T,=O”C
to +7O”C
1 Notes
2
I
Sym.
t*“n”
tp&p,
tw, F,
tp, FH
t
Alternative CE#-Controlled
ns
ns
Writes for notes 1 through 5.
Vbc=3.3V+0.3V,
Versiond5)
Parameater
. .a.-...---.
Write
RP#
WE#
CE#
RP#
Unit
EE
3
3
See 5.OV V,,
LH28F008SGL150
Min.
Max.
150
1
0
70
50
50
5
5
0
25
”f-l
Cycle Time
High Recovery to CE# : Going Low
Setup to CE# uullly
p-‘-LOW
’
Pulse Width
V,, Setup to Ccw
T,=O”C
to +70X
I
LH28F008SC-L120
Min.
Max.
Unit
.--
2
3
tfq&,
CE# Pulse Width High
CE# High to RY/BY# Going Low
tp)+q
ffzHr,,
Write Recovery before Read
Vpp Hold from Valid SRD, RY/BY# High
2,4
hNl
2,4
w?OVPH RP# VHH Hold from Valid SRD, RY/BY# High
NOTE:
See 5V Vc, Alternative CE#-Controlled
Writes for Notes 1 through 5.
1
0
-7n
i---c--
p.S
I
t
25
100
0
0
0
ns
nc
ns
I I.2
ns
ns
ns
ns
ns
Rev. 1.0
LHF08CH2
etuo to Cl
7”
40
5
5
0
9r;
-!
II>
ns
ns
ns
ns
-A
NOTES:
1. In systems where CE# defines the write pulse width (within a longer WE# timing waveform), all setup, hold, and
inactive WE# times should be measured relative to the CE# waveform.
2. Sampled, not 100% tested.
3. Refer to Table 4 for valid A,, and DIN for block erase, byte write, or lock-bit config.uration.
4. V,, should be held at VPPHl12,s ( and if necessary RP# should be held at V,,) until determination of block erase
byte write, or lock-bit configuration success (SR.1/3/4/5=0).
5. See Ordering Information for device speeds (valid operational combinations).
6. See Transient Input/Output Reference Waveform and Transient Equivalent Testing Load Circuit (High Seed
Configuration) for testing characteristics.
7. See Transient Input/Output Reference Waveform and Transient Equivalent Testing Load Circuit (Standard
Configuration) for testing characteristics.
Rev. 1 .ll
37
LHF08CH2
1
A----
2
3
4
5
A
VIH
ADDRESSES(A)
VIL
VIH
WE#(W)
VIL
OE#(G)
VIH
CE#(E)
VIL
VIH
DATA( D/Q)
VIL
VOH
RY/BY#(R)
VOL J
VHH
RP#(P)
VIH
VIL
NOTES:
1. Vcc power-up
2. Write block
3. Write block
4. Automated
5. Read status
6. Write Read
-
and standby.
erase or byte write setup.
erase confirm or valid address
erase or program
delay.
register data.
Array command.
Figure
and data.
17. AC Waveform
for CE#-Controlled
Write Operations
Rev. 1.0
SHARP
LHF08CH2
2.7 RESET OPERATIONS
VOH
RY/BY#(R)
VOL
VIH
FlP#(P)
VIL
(A)Reset
During
Read Array
Mode
VOH
RY/BY#(R)
VOL
p
tPLAH
VIH
RP#(P)
VIL
(B)Reset
During
Block
2.7Vi3.3Vi5V
Erase,
Byte Write,
or Lock-Bit
Configuretion
L
vcc
ML
-
b35VPH
-
VIH
I
RP#(P)
7-
VIL
(C)RP#
Figure 18. AC Waveform
Sym.
‘LPH
‘LRH
35VPH
Parameter
RP# Pulse Low Time
(If RP# is tied to Vcc, this
specification is not applicable)
RP# Low to Reset during
Block Erase, Byte Write or
Lock-Bit Configuration
V,, 2.7V to RP# High
V,, 3.OV to RP# High
Vco 4.5V to RP# High
rising
for Reset Operation
Reset AC Specifications(‘)
Vr.,=2.7V
Notes
Min.
Max.
100
Vn,=3.3V
Max.
Min.
V~+iV
Min.
Max.
100
100
-
2,3
4
Timing
100
100
ns
12
20
100
Unit
P
ns
ITES:
These specifications are valid for all product versions (packages and speeds).
If RP# is asserted while a block erase, byte write, or lock-bit configuration operation is not executing, the reset
will complete within 1OOns.
A reset time, tPHQV, is required from the latter of RY/BY# or RP# going high until outputs are valid.
When the device power-up, holding RP# low minimum 1OOnsis required after Vcc has been in predefined range
and also has been in stable there.
Rev. 1.0
LHF08CH2
6.2.8
:wHQv4
BLOCK
ERASE,
BYTE WRITE AND LOCK-BIT
Clear Block Lock-Bits
Time
CONFIGURATION
2
PERFORMANCE(3~4~5)
1.1
5
1
4
S
5.6
7
5.2
7.5
P
9.4
13.1
9.8
12.6
IJS
FHOVA
tWHRH,
tF,,RH,
Byte Write Suspend
Read
)“HnHz
Erase Suspend
Latency Time to
Latency Time to Read
FHRH7
NOTES:
1. Typical values measured at TA=+25”C and nominal voltages. Assumes corresponding
lock-bits are not set.
Subject to change based on device characterization.
2. Excludes system-level overhead.
3. These performance numbers are valid for all speed versions.
4. Sampled but not 100% tested.
5. Block erase, byte write and lock-bit configuration operations with Vccc3.OV and/or VPP<3.0V are not
guaranteed.
Rev. 1.3
SHARP
LHF08CH2
ADDITIONAL
1 Ordering
INFORMATION
Information
Product line designator for all SHARP Flash products
I
I
I
~L~H12/81F~O~018/SICi(H~RlDevice Density
008 = 8-Mbit
Access Speed (ns)
85:85ns(5V,30pF),
90ns(5V),
120ns(3.3V), 150ns(2.7V)
12:120ns(5V), 150ns(3.3V)
170ns(2.7V)
F
Architecture
S = Regular Block
Power Supply Type
C = SmartVoltage Technology
~
Operating Temperature
‘Blank = 0°C - +7O”C
H = -40°C - +85”C _
)ption
1
Order Code
LH28FOO8SCFbL85
V,,=2.7-3.6V
5OpF load,
1.35V I/O Levels
LH28F008SC-L150
lLl815j
w
ul
Pat kage
T = 40-Lead TSOP
R = 40-Lead TSOP(Reverse
N = 44-Lead PSOP
B = 42 or 48-Ball CSP
Valid Operational
Combinations
v,,=3.3*0.3v
vc+.o*o.5v
1OOpF load,
5OpF load,
TTL l/O Levels
1.5V I/O Levels
LH28F008SC-L120
LH28F008SC-L90
Bend)
Vcc=5.0~0.25V
3OpF load,
1.5V I/O Levels
LH28F008SC-L85
Rev. 1.0
LHF08CH2
SHARP
8 Package and packing
-
specification
1
1
1. Package Outline Specification
Refer to drawing No.AA
2. Markings
2 - 1. Marking contents
( 1) Product name :
( 2 ) Company name :
(3) Date code
(Example) Y Y WW
1 1 12
LH28F008SCR-L85
SHARP
xxx
Indicates
the product
(Lower
(4) The marking of “JAPAN” indicates
the country
2 - 2. Marking layout
Refer drawing No.AAl
1 1 2
(This layout does not define the dimensions of marking
3.
was manufactured
two digits
of the year.)
of origin.
character
and mark ing position.)
Pack ing Specification
(Dry packing for surface
mount packages)
Dry packing is used for the purpose of maintaining
IC quality
after mounting
packages on the PCB (Printed
Circuit
Board),
When the epoxy resin which is used for plastic
packages is stored at high
humidity,
it may absorb 0.15% or more of its weight in moisture.
If the surface
mount type package for a relatively
large chip absorbs a large amount of moisture
between the epoxy resin and insert material
(e.g. chip,lead
frame) this moisture
may suddenly vaporize
into steam when the entire package is heated during the
soldering
process (e.g. VPS). This causes expansion and results
in separation
between the resin and insert material,
and sometimes cracking
of the package.
This dry packing is designed to prevent the above problem from occurring
in
surface mount packages.
- 1. Packing Materials
Material
Name
Material
Specificaiton
Purpose
Conductive
plastic
(50devices/tray)
Fixing of device
Tray
_____________.__________________________--~-----~~---~~~----~------~-~----~~-----~~~~-~-----~~~~---~~~~--..----~.----~------.---------------------________
Upper
cover
tray
Conductive
plast
ic
(ltray/case)
Fixing
of device
________________________________________---------.---------------------------------------------------___--____-____-_________________________---_______._.
Laminated aluminum bag Aluminum polyethylene
(lbag/case)
Drying of device
________________________________________-------------------------------------------------------------------------------------------------------------------.
Desiccant
Silica
gel
Drying
of device
__._____________________________________---.---------.
._______________________________________~~~~~~~~~.~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
P
P band
Polypropylene
(3pcs/case)
Fixing of tray
________________________________________~~-~~~~---~~~---~~~~~~~~~~~~~~~~~~~~~~~~.~~~~~~~.~~~~~~~~.~~~~~.~~~~~~~~~~~~~~~~~~~~
Inner
case
Card
board
(500devices/case)
Packaging of device
________________________________________~~.--~~..--~~~--~~~~~---~~~~.--~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~.~~~~~-~~~~~~-~~~~~
Label
Paper
Indicates
part number,quantit]
and
date
of
manufacture
,____________.______~~~~~..~~~~..~~~~~~.~~~~~~~~~~.~.~~~~~~.~~~~~~.~~~~~~~.~~~~~~~~~~.~.~~~~~~...~~~~...~~~~~.~.~~~~.~~~~~~.~~~~~~
Card board
Outer case
Cuter packing of tray
(Devices shall be placed into a tray in the same direction.)
LHF08CH2
SHARP
3 - 2.
Storage
4.
5.
Outline dimension
Refer to attached
42
of tray
drawing
and Opening of Dry Packing
4-l.
Store under conditions
shown below before opening
( 1) Temperature range
: 5-40°C
(2)
Humidity
: 80% RH or less
the dry packing
4 - 2.
Notes on opening the dry packing
(1)
Before opening the dry packing,
prepare a working
table
grounded against ESD and use a grounding strap.
(2)
The tray has been treated to be conductive
or anti-stat i
device is transferred
to another tray, use a equivalent
which
is
c. If the
tray.
4-3.
Storage after opening the dry packing
Perform the following
to prevent absorption
of moisture
after opening.
(1)
After opening the dry packing,
store the ICs in an environment
with a
temperature
of 5-25°C
and a relative
humidity of 60% or less and
mount ICs within
72 hours after opening dry packing.
4 -4.
Baking (drying)
before mounting
( 1)
Baking is necessary
(A)
If the humidity indicator
in the desiccant
becomes pink
(B)
If the procedure
in section 4-3 could not be performed
( 2)
Recommended baking conditions
If the above conditions
(A) and (B) are applicable,
bake it before
mounting, The recommended conditions
are 16-24 hours at 120°C.
Heat resistance
tray is used for shipping tray.
Surface
Mount Conditions
Please perform the following
quality.
conditions
when mounting
ICs not to deteriorate
IC
5-l .Soldering
conditions(Tbe
following
conditions
are valid only for one time soldering.)
Temperature and Duration
Measurement Point
Mounting Method
Reflow soldering
Peak temperature
of 230°C or less,
IC package
(air)
duration
of less than 15 seconds.
surface
200°C or over,duration
of less than 40 seconds.
Temperature increase
rate of l--4’Vsecond
_______.__________._____________________-------------------.-------------------------------------------------------.
___________________._____________
Manual soldering
260°C or less, duration
of less
IC outer lead
(soldering
iron)
than 10 seconds.
surface
5 - 2.
for removal of residua 1 flux
Cond itions
Ultrasonic
washing power
: 25 Watts/liter
(1)
Washing time
: Total 1 minute
(2)
Solvent temperature
: 15-40°C
(3)
or less
maximum
SHARP
LHF08CH2
LH28F008SCR-L85
JAPAN
YYWW
X
20. 0+-o. 3
0
.
h)
ul
It
xx
18. 4&O. 2
t-
\r.
ASE PLANE
SEE DETAIL
A
DETAIL A
;I% j
4ME $SOP40-P-lOZO(R
!J-FttJz
[ TIN-LEACIkii*
LEAD FINISH j PLATING
#{Z
j
MAWING NO. i AA1112
UNIT ! mm
‘1S~f~9);~b-'iM~~,t18~~ll~\bq)lff3.
NOTE Plastic
body dimensions
of resin.
do not include
burr
LHF08CH2
SHARP
tlw
mq
NOTE
qAME\TSOP40-1020TCM-RH
DRAWING NO. j CV644
qqiL
UNIT
j
1
mm
44
SHARF,
LHF708CH2
Flash
memory LHFXXCXX family
Noises
having
generated
a level
Such noises,
commands,
operating
the
operating
limit
undesired
the data stored
with
the flash
specified
conditions
when induced onto WEStsignal
causing
To protect
Data Protection
exceeding
under specific
45
the spec ificat
in
on may be
on some systems.
or power supply,
may be interpreted
as false
unwanted overwriting,
systems
memory updating.
in the flash
memory should
memory against
have the following
write
protect
designs,
as
appropriate:
1) Protecting
data
When a lock bit
using
this
in specific
is set,
section(locked
section)
be used to prevent
By controlling
For further
block
RI%, desired
information
When the level
memory
bit
blocks
is protected
space
through
can be divided
section).
overwriting.
into
The master
can be locked/unlocked
block
the
By
program
lock bit
can
bit
through
and control
the software.
ing of RP#, refer
4.9 and 4.10)
Vpp
of Vpp is lower than VPPLK (lockout
is disabled.
against
setting.
on setting/resetting
(See chapter
2) Data protection
write
flash
block
and data section(unlocked
false
to the specification.
flashmemory
the corresponding
the
feature,
block
voltage),
All blocks are lockedandthedata
write
operation
on the
intheblocksarecompletely
protected.
For the lockout
3) Data protect
voltage,
ion through
When the RP$ is kept
transition,
refer
write
to the specification.
6.2.3. )
RP#
low during
operation
(See chapter
power up and power down sequence
on the flash
memory is disabled,
write
such as vo 1 tage
protecting
all
blocks.
For the detai 1s of RPB control,
refer
to the specification.
(See chapter
5.6 and6.2.7.)
Rev 1.3