SIPEX SP8605

SP8603, SP8605, SP8610
12-Bit Sampling A/D Converters
■ 3µs, 5µs or 10µs Sample/Conversion
Time
■ Unipolar 0V to +10V and 0V to +5V
Input
■ No Missing Codes Over Temperature
■ AC Performance Over Temperature
72dB Signal–to–Noise Ratio at Nyquist
85dB Spurious–free Dynamic Range at
49kHz
–81dB Total Harmonic Distortion at 49kHz
■ Internal Sample/Hold, Reference,
Clock, and 3-State Outputs
■ Power Dissipation: 90mW
■ 28–Pin Narrow PDIP and SOIC
Packages
DESCRIPTION…
The SP86XX Series are complete, unipolar, 12-bit sampling A/D converters using state-of-the-art
CMOS structures. They contain a complete 12-bit successive approximation A/D converter with
internal sample/hold, reference, clock, digital interface for microprocessor control, and three-state
output drivers. Power dissipation is only 90mW. AC and DC performance are completely
specified. Sampling/conversion rates of 3µs, 5µs and 10µs are offered.
CS
R/C HBE
Control
Logic
0V to10VIN
Clock
Output
Latches
And
Three
State
Drivers
CDAC.....
.....
0V to 5VIN
Internal
Ref
VREF Output
(1.2043V)
Comparator
.....
.....
BUSY
SAR
Three
State
Parallel
Output
Data
Bus
79
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device
at these or any other above those indicated in the operation
sections of the specifications below is not implied. Exposure to
absolute maximum rating conditions for extended periods of time
may affect reliability.
Lead Temperature (soldering, 10s) ..................................... +300°C
Thermal Resistance. ØJA:
Plastic DIP ....................................................................... 50°C/W
SOIC .............................................................................. 100°C/W
VS to Digital Common ............................................................... +7V
Pin 26 (VSO) to Pin 27 (VSA) .................................................... ±0.3V
Analog Common to Digital Common ...................................... ±0.3V
Control Inputs to Digital Common ....................... –0.3 to VS + 0.3 V
Analog Input Voltage ................................................... –3.0/+16.5V
Maximum Junction Temperature ........................................... 160°C
Internal Power Dissipation .................................................. 750mW
SPECIFICATIONS
(TA = 25°C; Sampling Frequency, FS, = 333kHz for SP8603, 200kHz for SP8605, 100kHz for SP8610, VS = +5V, unless otherwise specified.)
PARAMETER
MIN.
TYP.
MAX.
ANALOG INPUT
Voltage Ranges
0V to +5V, 0V to +10V
Impedance
0 to +10V Range
5.4
7.7
10.0
0 to +5V Range
3.9
5.6
7.3
DC PERFORMANCE
Full Scale Error
–K
±0.1
±0.50
Integral Linearity Error
–K
±0.35
±0.75
Differential Linearity Error
–K
±0.35
±0.95
No Missing Codes
Guaranteed
Unipolar Zero
–K
±1
±5
INTERNAL REFERENCE
Voltage Output
1.1440 1.2043 1.2645
Output Source Current
100
Output Resistance
280
AC PERFORMANCE
SP8603
Conversion Time
2.6
Complete Cycle
3.0
Throughput Rate
333
Spurious-Free Dynamic Range
@ 49kHz
85
@ 161kHz
72
Total Harmonic Distortion
@ 49kHz
–81
@ 161kHz
–71
Signal to Noise Ratio (SNR)
@ 49kHz
72
@ 161kHz
72
Signal to (Noise + Distortion) Ratio
@ 49kHz
71
@ 161kHz
68
SP8605
Conversion Time
4.5
Complete Cycle
5.0
Throughput Rate
200
Spurious-Free Dynamic Range
@ 49kHz
85
@ 97kHz
77
Total Harmonic Distortion
@ 49kHz
–81
@ 97kHz
–76
80
UNITS
V
kΩ
kΩ
%FSR
CONDITIONS
Unipolar
TMIN ≤ TA ≤ TMAX
TMIN ≤ TA ≤ TMAX
Externally adjustable to zero;
TMIN ≤ TA ≤ TMAX
Note 1
LSB
LSB
LSB
Externally adjustable to zero
TMIN ≤ TA ≤ TMAX
V
µA
Ω
TMIN ≤ TA ≤ TMAX
µs
µs
kHz
Note 2
dB
dB
Note 2
dB
dB
Note 2
dB
dB
Note 2
dB
dB
µs
µs
kHz
Note 2
dB
dB
Note 2
dB
dB
SPECIFICATIONS
(TA = 25°C; Sampling Frequency, FS, = 333kHz for SP8603, 200kHz for SP8605, 100kHz for SP8610, VS = +5V, unless otherwise specified.)
PARAMETER
MIN.
AC PERFORMANCE
SP8605
Signal to Noise Ratio (SNR)
@ 49kHz
@ 97kHz
Signal to (Noise + Distortion) Ratio
@ 49kHz
@ 97kHz
SP8610
Conversion Time
Complete Cycle
10.0
Throughput Rate
Spurious-Free Dynamic Range
Total Harmonic Distortion
Signal to Noise Ratio (SNR)
Signal to (Noise + Distortion) Ratio
TYP.
MAX.
–65
CONDITIONS
TMIN ≤ TA ≤ TMAX
Note 2
72
72
dB
dB
71
70
dB
dB
9.5
µs
µs
kHz
dB
dB
dB
dB
Note 2
100
85
–81
72
71
SAMPLING DYNAMICS
Aperture Delay
13
Aperture Jitter
150
Transient Response
–K
150
Overvoltage Recovery
150
DIGITAL INPUTS
Logic Levels
VIL
–0.3
+0.8
VIH
+2.4
+5.3
IIL
±0.1
±50
IIH
±5
DIGITAL OUTPUTS
Resolution
12
Data Format
Parallel; 12-bit or 8-bit/4-bit
Data Coding
Binary
0.0
+0.4
VOL
VOH
+2.4
VDD
ILEAKAGE (High-Z State)
±0.1
±5
POWER SUPPLY REQUIREMENTS
Rated Voltage
+4.75
+5.0
+5.25
Current
18
21
Power Consumption
90
ENVIRONMENTAL AND MECHANICAL
Specification
–K
0
+70
Storage
Package
–KN
–KS
UNITS
+150
@ 49kHz; Note 2
@ 49kHz; Note 2
@ 49kHz; Note 2
@ 49kHz; Note 2
ns
ps, rms
Note 3
ns
ns
Note 4
V
V
µA
µA
Bits
V
V
µA
ISINK = 1.6mA
ISOURCE = 1.6mA
V
mA
mW
VS (VSA and VSD)
IS
°C
°C
28–pin Narrow DIP
28–pin SOIC
NOTES
1.
LSB means Least Significant Bit. For SP86xx Series, 1LSB = 1.22mV for 5V range, 1 LSB =
2.44mV for 10V range.
2.
All specifications in dB are referred to a full-scale input, either 10V or 5V.
3.
For full-scale step input, 12-bit accuracy attained in specified time.
4.
Recovers to specified performance in specified time after 2 x FS input overvoltage.
81
HBE is HIGH.
PINOUT
N.C. 1
±10V IN 2
28 N.C.
27 VSA
26 VSD
±5V IN 3
VREF 4
AGND 5
D11
6
D10
7
D9
8
D8
9
25 N.C.
SP8603
SP8605
SP8610
24 BUSY
23 CS
22 R/C
21 HBE
20 D0
D7 10
19 D1
D6 11
18 D2
D5 12
17 D3
D4 13
16 DGND
15 N.C.
N.C. 14
Pin 13 — D4 — Data Bit 4 if HBE is LOW; LOW if
HBE is HIGH.
Pin 14 —N.C.—This pin is not internally connected.
Pin 15 —N.C.—This pin is not internally connected.
Pin 16— DGND — Digital Ground. Connect to
pin 5 at the device.
Pin 17 — D3 — Data Bit 3 if HBE is LOW; Data Bit
11 if HBE is HIGH.
Pin 18 — D2 — Data Bit 2 if HBE is LOW; Data Bit
10 if HBE is HIGH.
Pin 19— D1 — Data Bit 1 if HBE is LOW; Data Bit
9 if HBE is HIGH.
PIN ASSIGNMENT
Pin 1 —No Connection —This pin is not internally
connected.
Pin 2 — IN1 — 0V to 10V Analog Input. Connected
to AGND for 10V range.
Pin 3 — IN2 — 0V to 5V Analog Input. Connected
to AGND for 5V range.
Pin 4 — VREF – Internal Voltage. Reference Output.
Pin 5 — AGND — Analog Ground. Connect to
pin 16 at the device.
Pin 6 — D11 — Data Bit 11. Most Significant Bit
(MSB).
Pin 7 — D10 — Data Bit 10.
Pin 8— D9 — Data Bit 9.
Pin 9 — D8 — Data Bit 8.
Pin 10 — D7 — Data Bit 7 if HBE is LOW; LOW if
HBE is HIGH.
Pin 11 — D6 — Data Bit 6 if HBE is LOW; LOW if
HBE is HIGH.
Pin 12 — D5 — Data Bit 5 if HBE is LOW; LOW if
82
Pin 20 — D0 — Data Bit 0 if HBE is LOW. Least
Significant Bit (LSB). Data Bit 8 if HBE is HIGH.
Pin 21 — HBE — High Byte Enable, When held
LOW, data output as 12-bits in parallel. When
held HIGH, four MSBs presented on pins 17–
20, pins 10 – 13 output LOWs. Must be LOW to
initiate conversion.
Pin 22— R/C — Read/Convert. Falling edge initiates
conversion when CS is LOW, HBE is LOW, and
BUSY is HIGH.
Pin 23 — CS — Chip Select. Outputs in Hi-Z state
when HIGH. Must be LOW to initiate conversion or
read data.
Pin 24 — BUSY — Output LOW during
conversion. Data valid on rising edge in Convert Mode.
Pin 25 — N.C. — This pin is not internally connected.
Pin 26 — VSD — Positive Digital Power Supply, +5V.
Connect to pin 27, and bypass to DGND.
Pin 27 — VSA — Positive Analog Power Supply.
+5V. Connect to pin 26, and bypass to AGND.
Pin 28 — N.C. — This pin is not internally connected.
FEATURES...
The SP86XX Series are specified at sampling
rates of 333kHz (SP8603), 200kHz (SP8605) or
100kHz (SP8610). Conversion times are factory
set for 2.70µs, 4.7µs and 9.7µs maximum, respectively, over temperature, and the highspeed sampling input stage insures a total acquisition and conversion time of 3µs, 5µs and 10µs
maximum, respectively, over temperature. Precision, laser-trimmed scaling resistors provide
industry-standard input ranges of 0V to +5V or
0V to +10V.
The 28-pin SP86XX Series are available in
narrow plastic DIP, and SOIC packages and it
operates from a single +5V supply. The SP86XX
Series are available in grades specified over the
0°C to +70°C commercial temperature ranges.
OPERATION
Basic Operation
Figure 1 shows the simple hookup circuit required
to operate the SP86XX Series in a 0V to +10V
range in the Convert Mode. A convert command
arriving on R/C puts the SP86XX Series in the
HOLD mode, and a conversion is started. This
pulse must be LOW for a minimum of 40ns.
Because this pulse establishes the sampling instant
of the A/D, it must have very low jitter. BUSY will
be held LOW during the conversion, and rises only
Input
1
N.C.
N.C. 28
2
IN 1
+5V 27
3
IN 2
+5V 26
4
VREF
5
AGND
6
D11 (MSB)
7
D10
R/C 22
8
D9
HBE 21
9
D8
D0 (LSB) 20
+5V
6.8µF +
0.1µF
N.C. 25
BUSY 24
Busy
The SP86XX Series will begin acquiring a new
sample just prior to the BUSY output rising, and
will track the input signal until the next conversion
is started.
In the Read Mode, R/C is kept normally LOW, and
a HIGH pulse is used to read data and initiate a
conversion. In this mode, the rising edge of R/C
will enable the output data pins, and the data from
the previous conversion becomes valid. The falling edge then puts the SP86XX Series in a hold
mode, and initiates a new conversion.
For use with an 8-bit bus, the data can be read out in two
bytes under the control of HBE. With a LOW input
on HBE, at the end of a conversion, the 8 LSBs of data
are loaded into the output drivers on D7 through D4 and
D3 through D0. Taking HBE HIGH then loads the 4
MSBs on D3 through D0, with D7 through D4 being
forced LOW.
Analog Input Ranges
The SP86XX Series offers two standard unipolar
input ranges: 0V to +10V and 0V to +5V. If a 10V
unipolar range is required, the analog input signal
should be connected to pin 2. A signal requiring a
5V unipolar range should be connected to pin 3. In
either case, the other pin of the two must be
grounded or connected to the adjustment circuits
described in the section on calibration.
CS 23
10 D7
D1 19
11 D6
D2 18
12 D5
D3 17
13 D4
DGND 16
14 N.C.
D11
(MSB)
after the conversion is completed and the data has
been transferred to the output drivers. Thus, the
rising edge can be used to read the data from the
conversion. Also, during conversion, the BUSY
signal puts the output data lines in Hi-Z states and
inhibits the input lines. This means that pulses on
R/C are ignored, so that new conversions cannot be
initiated during a conversion.
Convert
Command
N.C. 15
Data
Out
Figure 1. Basic 0V to 10V Operation
D0
(LSB)
Controlling The SP86XX Series
The SP86XX Series can be easily interfaced to most
microprocessor-based and other digital systems. The
microprocessor may take full control of each conversion, or the SP86XX Series may operate in a standalone mode, controlled only by the R/C input. Full
control consists of initiating the conversion and reading the output data at user command, transmitting data
either all 12-bits in one parallel word, or in two 8-bit
bytes. The three control inputs (CS, R/C and HBE) are
all TTL/CMOS compatible. The functions of the
83
CS
R/C
1
X
HBE BUSY
X
None – outputs in Hi-Z state.
0
1
Holds signal and initiates conversion.
0
1
0
1
Output three-state buffers enabled once
conversion has finished.
0
1
1
1
Enable hi-byte in 8-bit bus mode.
0
0
0
OPERATION
1
1
1
1
Inhibit start of conversion.
0
1
0
0
1
1
None – outputs in Hi-Z state.
X
X
X
0
Conversion in progress. Outputs Hi-Z
state. New conversion inhibited until
present conversion has finished.
Table 1. Control Line Functions
control lines are shown in Table 1.
For stand-alone operation, control of the SP86XX
Series is accomplished by a single control line
connected to R/C. In this mode, CS and HBE are
connected to GND. The output data are presented
as 12-bit words. The stand-alone mode is used in
systems containing dedicated input ports which do
not require full bus interface capability.
Conversion is initiated by a HIGH-to-LOW transition
on R/C. The three-state data output buffers are enabled
when R/C is HIGH and BUSY is HIGH. Thus, there
are two possible modes of operation: conversion can
be initiated with either positive or negative pulses. In
either case, the R/C pulse must remain LOW a
minimum of 40ns.
Figure 5 illustrates timing when conversion is initiated by an R/C pulse which goes LOW and returns
HIGH during the conversion. In this case (Convert
Mode), the three-state outputs go into the Hi-Z state in
response to the falling edge of R/C, and are enabled for
external access to the data after completion of the
conversion.
Figure 6 illustrates the timing when conversion is
initiated by a positive R/C pulse. In this mode (Read
Mode), the output data from the previous conversion
is enabled during the HIGH portion of R/C. A new
conversion starts on the falling edge of R/C, and the
three-state outputs return to the Hi-Z state until the next
occurrence of a HIGH on R/C.
Conversion Start
A conversion is initiated on the SP86XX Series only
by a negative transition occurring on R/C, as shown
84
in Table 2. No other combination of states or transitions will initiate a conversion. Conversion is inhibited
if either CS or HBE are HIGH, or if BUSY is LOW.
CS and HBE should be stable a minimum of 25ns
prior to the transition on R/C. Timing relationships for
start of conversion are illustrated in Figure 7.
The BUSY output indicates the current state of the
converter by being LOW only during conversion.
During this time the three-state output buffers remain
in a Hi-Z state, and therefore data cannot be read
during conversion. During this period, additional
transitions on the three digital inputs (CS, R/C and
HBE) will be ignored, so that conversion cannot be
prematurely terminated or restarted.
Internal Clock
The SP86XX Series has an internal clock that is
factory trimmed to achieve the typical conversion
times given in the specifications, and a maximum
conversion time over the full operating temperature range of 2.7µs, 4.7µs or 9.7µs, depending on
the model. No external adjustments are required,
and with the guaranteed maximum acquisition
time of 300ns, throughput performance is assured
with convert pulses as close as 3µs for the SP8603.
Reading Data
After conversion is initiated, the output buffers remain
in a Hi-Z state until the following three logic conditions are simultaneously met: R/C is HIGH, BUSY is
HIGH and CS is LOW. Upon satisfying these conditions, the data lines are enabled according to the state
of HBE. See Figure 7 for timing relationships and
specifications.
CALIBRATION...
Optional External Gain And Offset Trim
Offset and full-scale errors may be trimmed to zero
using external offset and full-scale trim potentiometers connected to the SP86XX Series as shown
in Figure 3.
If adjustment of offset and full scale is not required,
+10V
Input
2
3
SP8603/05/10
+5V
Input
2
SP8603/05/10
3
Figure 2. a) 10V Range b) 5V Range — Without Trims
INPUT VOLTAGE RANGE AND LSB VALUES
Input Voltage Range Defined As:
0V to +10V
0V to +5V
Analog Input Connected to Pin
2
3
Pin Connected to AGND
3
2
10V/212
2.44mV
5V/212
1.22mV
One Least Significant Bit (LSB)
FSR/212
OUTPUT TRANSITION VALUES
FFEH TO FFFH
7FFH TO 800H
+ FULL SCALE
+10V–3/2LSB
+5V–3/2LSB
+9.963V
+4.9982V
Mid Scale
4.9988V
2.4994V
0V
1.22mV
0.6mV
000H to 001H
Table 2. Input Voltages, Transition Voltages and LSB Values
connections as shown in Figure 2 should be used.
FFEH = 4094DEC.
Calibration Procedure
Apply a precision input voltage source to your
chosen input range (10V range at pin 2 or 5V at
pin 3). Set the A/D to convert continuously.
Monitor the output code. Trim the offset first,
then gain. Use the appropriate input voltages
and output target codes for your chosen input
range as follows. The recommended offset calibration voltage values eliminate interaction between the offset and gain calibration
+10V Range Offset and Gain
Offset — Apply 0.0012V to the +10V input at
pin 2. Adjust the offset potentiometer until the
LSB toggles on and off at code 0000 0000
0000BIN = 000H = 0000DEC.
Gain — Apply 9.9963V to the +10V input at pin
2. Adjust the gain potentiometer until the LSB
toggles on and off at code 1111 1111 1110BIN =
FFEH = 4094DEC.
+5V Range Offset and Gain
Offset — Apply 0.0006V to the +5V input at pin
3. Adjust the offset potentiometer until the LSB
toggles on and off at code 0000 0000 0000BIN =
000H = 0000DEC.
Layout Considerations
Because of the high resolution and linearity of the
SP86XX Series, system design problems such as
ground path resistance and contact resistance become
very important.
Gain — Apply 4.9982V to the +5V input at pin
3. Adjust the gain potentiometer until the LSB
toggles on and off at code 1111 1111 1110BIN =
GAIN ADJUST
+10V
Input R2=500Ω
+5V
2
3
4
5
R1=10KΩ
10KΩ 100Ω 6
6.65KΩ
7
–15V
The input resistance of the SP86XX Series is 6.3kΩ
or 4.2KΩ (for the 10V and 5V ranges respectively).
GAIN ADJUST
SP86XX
+5V
Input
R2=500Ω
+5V
R1=10KΩ
10KΩ
a)
30.1KΩ 301Ω
–15V
UNIPOLAR ZERO ADJUST
2 SP86XX
3
4
5
6
7
b)
Figure 3. a) 10V Range b) 5V Range — With External Trims
85
To avoid introducing distortion, the source resistance
must be very low, or constant with signal level. The
output impedance provided by most op amps is ideal.
Pins 26 Digital Supply Voltage (VSD) and 27 Analog
Supply Voltage (VSA) are brought out to separate pins
to maximize accuracy on the chip. They should be
connected together as close as possible to the unit. Pin
27 may be slightly more sensitive than pin 26 to supply
variations, but to maintain maximum system accuracy, both should be well–isolated from digital supplies with wide load variations.
The GND pins (5 and 16) are also separated internally,
and should be directly connected to a ground plane
under the converter. A ground plane is usually the best
solution for preserving dynamic performance and
reducing noise coupling into sensitive converter circuits. Where any compromises must be made, the
common return of the analog input signal should be
referenced to pin 5, AGND, on the SP86XX Series,
which prevents any voltage drops that might occur in
the power supply common returns from appearing in
series with the input signal.
To limit the effects of digital switching elsewhere in a
system on the analog performance of the system, it
often makes sense to run a separate +5V supply
conductor from the supply regulator to any analog
components requiring +5V, including the SP86XX
Series. If the SP86XX Series traces cannot be
separated back to the power supply terminals, and
therefore share the same trace as the logic supply
currents, then a 10 Ohm isolating resistor should be
used between the board supply and pin 24 (VDA) and
its bypass capacitors to keep VDA glitch–free. The VS
pins (26 and 27) should be connected together and
bypassed with a parallel combination of a 6.8µF
Tantalum capacitor and a 0.1µF ceramic capacitor
located close to the converter to obtain noise-free
operation. (See Figure 1). Noise on the power supply
lines can degrade converter performance, especially
noise and spikes from a switching power supply.
Appropriate supplies or filters must be used.
Coupling between analog input and digital lines should
be minimized by careful layout. For instance, if the
lines must cross, they should do so at right angles.
Parallel analog and digital lines should be separated
from each other by a pattern connected to common.
If external full scale and offset potentiometers are
used, the potentiometers and related resistors should
be located as close to the SP86XX Series as possible.
“Hot Socket” Precaution
Two separate +5V VS pins, 26 and 27, are used to
minimize noise caused by digital transients. If one pin
is powered and the other is not, the SP86XX Series
may draw excessive current. In normal operation, this
is not a problem because both pins will be soldered
together. However, during evaluation, incoming inspection, repair, etc., where the potential of a “Hot
Socket” exists, care should be taken to apply power to
R/C
tB
BUSY
t DBC
tC
Converter Acquisition
Mode
Conversion
Acquisition
Conversion
tAP
Hold Time
SYMBOL/PARAMETER
TYP.
MAX.
tDBC
BUSY delay from R/C
MIN.
80
150
ns
tB
BUSY Low
2.5
2.7
µs
SP8603
4.5
4.7
µs
SP8605
9.5
9.7
µs
SP8610
tAP
Aperture Delay
∆tAP
Aperture Jitter
150
tC
Conversion Time
2.47
4.47
9.47
Figure 4. Acquisition and Conversion Timing
86
13
UNITS
ns
ps, rms
2.70
4.70
9.70
µs
µs
µs
SP8603
SP8605
SP8610
tW
R/C
tB
BUSY
t DBC
t DBE
tAP
Converter
Mode
Acquire
Acquire
Convert
tC
t DB
t HDR and t HL
Data
BUS
Data Valid
Convert
tA
Hi-Z State
Data Valid
Hi-Z State
Figure 5. Convert Mode Timing — R/C Pulse LOW, Outputs Enabled After Conversion
the SP86XX Series only after it has been socketed.
Minimizing “Glitches”
Coupling of external transients into an analog-todigital converter can cause errors which are difficult to
debug. In addition to the discussions earlier on layout
considerations for supplies, bypassing and grounding,
there are several other useful steps that can be taken to
get the best analog performance out of a system using
the SP86XX Series. These potential system problem
sources are particularly important to consider when
developing a new system, and looking for the causes
of errors in breadboards.
R/C
First, care should be taken to avoid glitches during
critical times in the sampling and conversion process.
Since the SP86XX Series has an internal sample/hold
function, the signal that puts it into the hold state (R/C
going LOW) is critical, as it would be on any sample/
hold amplifier. The R/C falling edge should have a 5
to 10ns transition time, low jitter, and have minimal
ringing, especially during the 20ns after it falls.
Although not normally required, it is also good practice to avoid glitches from coupling to the SP86XX
Series while bit decisions are being made. Since the
above discussion calls for a fast, clean rise and fall on
tW
tB
BUSY
t DBC
t DBE
tAP
Converter
Mode
Acquire
Convert
Data
BUS
Hi-Z State
Convert
Acquire
tC
t DD
tAP
tA
t HDR and t HL
Data
Valid
Hi-Z State
Data
Valid
Hi-Z State
Figure 6. Read Mode Timing — R/C Pulse HIGH, Outputs Enabled Only When R/C is High
87
AC DYNAMIC TIMING DATA
SYMBOL/PARAMETER
MIN .
TYP.
MAX.
80
150
ns
2.47
2.7
µs
40
UNITS
tW
R/C Pulse Width
tDBC
BUSY delay from R/C
ns
tB
BUSY LOW
tAP
Aperture Delay
13
ns
∆tAP
Aperture Jitter
150
ps, rms
tC
Conversion Time
2.5
tDBE
BUSY from End of Conversion
tDB
BUSY Delay after Data Valid
tA
Acquisition Time
t A + tC
Throughput Time
2.70
µs
75
200
ns
130
300
ns
100
25
ns
SP8603
3.0
µs
SP8605
5.0
µs
SP8610
10.0
µs
tHDR
Valid Data Held After R/C LOW
20
50
ns
tS
CS or HBE LOW before R/C Falls
25
5
ns
tH
CS or HBE LOW after R/C Falls
25
tDD
Data Valid from CS LOW, R/C HIGH, and HBE
0
ns
65
150
ns
50
150
ns
in Desired State (Load = 100pF)
tHL
Delay to Hi-Z State after R/C Falls or
CS Rises (3KΩ Pullup or Pulldown
All parameters Guaranteed By Design.
R/C, it makes sense to keep the rising edge of the
convert pulse outside the time when bit decisions are
being made. In other words, the convert pulse should
either be short (under 100ns so that it transitions before
the MSB decision), or relatively long (i.e., for the
SP8603, over 2.75µs to transition after the LSB
decision).
Next, although the data outputs are forced into a Hi-Z
state during conversion, fast bus transients can still be
capacitively coupled into the SP86XX Series. If the
data bus experiences fast transients during conversion, these transients can be attenuated by adding a
logic buffer to the data outputs. The BUSY output can
be used to enable the buffer.
Naturally, transients on the analog input signal are to
be avoided, especially at times within ±20ns of R/C
going LOW, when they may be trapped as part of the
charge on the capacitor array. This requires careful
88
layout of the circuit in front of the SP86XX Series.
Finally, in multiplexed systems, the timing relative to
when the multiplexer is switched may affect the
analog performance of the system. In most applications, the multiplexer can be switched as soon as R/C
goes LOW (with appropriate delays), but this may
affect the conversion if the switched signal shows
glitches or significant ringing at the SP86XX Series
input. Whenever possible, it is safer to wait until the
conversion is completed before switching and multiplexer. The extremely fast acquisition time and conversion time of the SP86XX Series make this practical in many applications.
CS or
HBE
tS
tW
R/C
BUSY
Data
BUS
tH
t DBC
Data Valid
Hi-Z State
t HDR and t HL
Figure 7. Conversion Start Timing
ORDERING INFORMATION
0°C to +70°C
Model
Throughput
Package
SP8603KN .................................................................... 333kHz ............................................................................................... 28–pin, 0.3" Plastic DIP
SP8603KS .................................................................... 333kHz ........................................................................................................ 28–pin, 0.3" SOIC
SP8605KN .................................................................... 200kHz ............................................................................................... 28–pin, 0.3" Plastic DIP
SP8605KS .................................................................... 200kHz ........................................................................................................ 28–pin, 0.3" SOIC
SP8610KN .................................................................... 100kHz ............................................................................................... 28–pin, 0.3" Plastic DIP
SP8610KS .................................................................... 100kHz ........................................................................................................ 28–pin, 0.3" SOIC
89