SL74HC623 Octal 3-State Noninverting Bus Transceiver High-Performance Silicon-Gate CMOS The SL74HC623 is identical in pinout to the LS/ALS623. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The SL74HC623 is a 3-state noninverting transceiver that is used for 2-way communication between data buses. Two separate enables are available. The enable for bus A to B is active-high, the enable for bus B to A is active-low. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION SL74HC623N Plastic SL74HC623D SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Control Inputs PIN 20=VCC PIN 10 = GND Output Enable Direction Operation L L Data Transmitted from Bus B to Bus A L H Data Transmitted from Bus A to Bus B H L Buses Isolated L H (High Impedance State) SLS System Logic Semiconductor SL74HC623 MAXIMUM RATINGS * Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin ±20 mA DC Output Current, per Pin ±35 mA ICC DC Supply Current, VCC and GND Pins ±75 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 °C 260 °C VOUT IIN IOUT Tstg Storage Temperature TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter DC Supply Voltage (Referenced to GND) VIN, VOUT DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, t f Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min Max Unit 2.0 6.0 V 0 VCC V -55 +125 °C 0 0 0 1000 500 400 ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. I/O pins must be connected to a properly terminated line or bus. SLS System Logic Semiconductor SL74HC623 DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Guaranteed Limit Test Conditions V 25 °C to -55°C ≤85 °C ≤125 °C Unit Minimum High-Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT≤ 20 µA 2.0 4.5 6.0 1.5 3.15 4.2 1.5 3.15 4.2 1.5 3.15 4.2 V VIL Maximum Low -Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT ≤ 20 µA 2.0 4.5 6.0 0.5 1.35 1.8 0.5 1.35 1.8 0.5 1.35 1.8 V VOH Minimum High-Level Output Voltage VIN=VIH or VIL IOUT ≤ 20 µA 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 4.5 6.0 3.98 5.48 3.84 5.34 3.7 5.2 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 VIN= VIL or VIH IOUT ≤ 6.0 mA IOUT ≤ 7.8 mA 4.5 6.0 0.26 0.26 0.33 0.33 0.4 0.4 Symbol Parameter VIH VIN=VIH or VIL IOUT ≤ 6.0 mA IOUT ≤ 7.8 mA VOL Maximum Low-Level Output Voltage VIN= VIL or VIH IOUT ≤ 20 µA V IIN Maximum Input Leakage Current VIN=VCC or GND, Pin 1 or 19 6.0 ±0.1 ±1.0 ±1.0 µA IOZ Maximum Three-State Leakage Current Output in High-Impedance State VIN= VIL or VIH VOUT=VCC or GND, I/O Pins 6.0 ±0.5 ±5.0 ±10 µA ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND IOUT=0µA 6.0 8.0 80 160 µA SLS System Logic Semiconductor SL74HC623 AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input t r=t f=6.0 ns) VCC Symbol Parameter Guaranteed Limit V 25 °C to -55°C ≤85°C ≤125°C Unit tPLH, t PHL Maximum Propagation Delay, A to B , B to A (Figures 1 and 3) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns tPLZ, t PHZ Maximum Propagation Delay , Direction or Output Enable to A or B (Figures 2 and 4) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tPZL, t PZH Maximum Propagation Delay , Direction or Output Enable to A or B (Figures 2 and 4) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tTLH, t THL Maximum Output Transition Time, Any Output (Figures 1 and 3) 2.0 4.5 6.0 60 12 10 75 15 13 90 18 15 ns Maximum Input Capacitance (Pin 1 or Pin 19) - 10 10 10 pF Maximum Three-State I/O Capacitance (I/O in High-Impedance State) - 15 15 15 pF CIN COUT Power Dissipation Capacitance (Per Transceiver Channel) CPD Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC Figure 1. Switching Waveforms SLS System Logic Semiconductor Typical @25°C,VCC=5.0 V 40 Figure 2. Switching Waveforms pF SL74HC623 Figure 3. Test Circuit Figure 4. Test Circuit EXPANDED LOGIC DIAGRAM SLS System Logic Semiconductor