TC9400 TC9401 TC9402 VOLTAGE-TO-FREQUENCY/FREQUENCY-TO-VOLTAGE CONVERTERS FEATURES Voltage-to-Frequency ■ ■ ■ ■ ■ ■ GENERAL DESCRIPTION Choice of Guaranteed Linearity: TC9401 ......................................................... 0.01% TC9400 ......................................................... 0.05% TC9402 ......................................................... 0.25% DC to 100 kHz (F/V) or 1Hz to 100kHz (V/F) Low Power Dissipation .......................... 27mW Typ Single/Dual Supply Operation ................................. + 8V to + 15V or ± 4V to ± 7.5V Gain Temperature Stability .......... ± 25 ppm/°C Typ Programmable Scale Factor ■ Operation ........................................... DC to 100 kHz Choice of Guaranteed Linearity: TC9401 ......................................................... 0.02% TC9400 ......................................................... 0.05% TC9402 ......................................................... 0.25% Programmable Scale Factor APPLICATIONS ■ ■ ■ ■ ■ ■ ■ 2 3 ORDERING INFORMATION Frequency-to-Voltage ■ ■ The TC9400/TC9401/TC9402 are low-cost voltage-tofrequency (V/F) converters utilizing low power CMOS technology. The converters accept a variable analog input signal and generate an output pulse train whose frequency is linearly proportional to the input voltage. The devices can also be used as highly-accurate frequency-to-voltage (F/V) converters, accepting virtually any input frequency waveform and providing a linearly-proportional voltage output. A complete V/F or F/V system only requires the addition of two capacitors, three resistors, and reference voltage. 1 µP Data Acquisition 13-Bit Analog-to-Digital Converters Analog Data Transmission and Recording Phase-Locked Loops Frequency Meters/Tachometer Motor Control FM Demodulation Part No. Linearity (V/F) TC9400COD 0.05% TC9400CPD 0.05% TC9400EJD 0.05% TC9401CPD 0.01% TC9401EJD 0.01% TC9402CPD 0.25% TC9402EJD 0.25% Package Temperature Range 14-Pin 0°C to +70°C SOIC (Narrow) 14-Pin 0°C to +70°C Plastic DIP 14-Pin – 40°C to +85°C CerDIP 14-Pin 0°C to +70°C Plastic DIP 14-Pin – 40°C to +85°C CerDIP 14-Pin 0°C to +70°C Plastic DIP 14-Pin – 40°C to +85°C CerDIP FUNCTIONAL BLOCK DIAGRAM 4 5 6 TC9400 Integrator Capacitor Input Voltage Integrator OpAmp Threshold Detector One Shot RIN IIN 7 Pulse Output ÷2 Reference Capacitor Pulse/2 Output IREF 8 Reference Voltage TC9400/1/2-5 11/6/96 TELCOM SEMICONDUCTOR, INC. 3-287 VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 *Static-sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to Absolute Maximum Rating Conditions for extended periods may affect device reliability. ABSOLUTE MAXIMUM RATINGS* VDD – VSS ................................................................. +18V IIN ...........................................................................10mA VOUT Max –VOUT Common .......................................... 23V VREF – VSS ..............................................................– 1.5V Storage Temperature Range ................ – 65°C to +150°C Operating Temperature Range C Device ................................................ 0°C to +70°C E Device ........................................... – 40°C to +85°C Package Dissipation (TA ≤ 70°C) 8-Pin CerDIP .................................................. 800mW 8-Pin Plastic DIP ............................................. 730mW 8-Pin SOIC .....................................................470mW Lead Temperature (Soldering, 10 sec) ................. +300°C ELECTRICAL CHARACTERISTICS: VDD = +5V, VSS = – 5V, VGND = 0V, VREF = – 5V, RBIAS = 100kΩ, Full Scale = 10kHz, unless otherwise specified. TA = +25°C, unless temperature range is specified (– 40°C to +85°C for E device, 0°C to +70°C for C device). VOLTAGE-TO-FREQUENCY Parameter Definition TC9401 TC9400 TC9402 Min Typ Max Min Typ Max Min Typ Max Accuracy Linearity 10 kHz Output Deviation From Straight Line Between Normalized Zero and Full-Scale Input Output Deviation From Straight Line Between Normalized Zero Reading and Full-Scale Input Variation in Gain A Due to Temperature Change Variation From Ideal Accuracy — 0.004 0.01 — 0.01 0.05 — 0.05 0.25 % Full Scale — 0.04 0.08 — 0.1 — 0.25 0.5 % Full Scale — ± 25 ± 40 — ± 25 ± 40 — ± 10 — ± 10 Correction at Zero Adjust for Zero Output When Input is Zero Variation in Zero Offset Due to Temperature Change — ± 10 ± 50 — ± 10 ± 50 — ± 50 ± 100 ppm/°C Full Scale — ± 10 – % of Nominal — ± 20 ± 100 mV — ± 25 ± 50 — ± 25 ± 50 — ± 50 ± 100 Full-Scale Analog Input Current to Achieve Specified Accuracy Overrange Current Settling Time to 0.1% Full Scale — 10 — — 10 — — — — 2 50 — — — — 2 50 — Logic "0" Output Voltage (Note 3) Voltage Range Between Output and Common — — 0.2 — 0.4 18 — — 0.2 — — 3 — — 3 Linearity 100 kHz Gain Temperature Drift (Note 1) Gain Variance Zero Offset (Note 2) Zero Temperature Drift (Note 1) Analog Input IIN Full Scale IIN Overrange Response Time Digital Section VSAT @ IOL = 10mA VOUT Max – VOUT Common (Note 4) Pulse Frequency Output Width 3-288 – 0.25 — Unit µV/°C 10 — µA — — — 2 50 — µA Cycle 0.4 18 — — 0.2 — 0.4 18 V V — — 3 — µsec TELCOM SEMICONDUCTOR, INC. VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 ELECTRICAL CHARACTERISTICS: (Cont.) VDD = +5V, VSS = – 5V, VGND = 0, VREF = – 5V, RBIAS = 100kΩ, Full Scale = 10kHz, unless otherwise specified. TA = +25°C, unless temperature range is specified – 40°C to +85°C for E device, 0°C to +70°C for C device. FREQUENCY-TO-VOLTAGE Parameter Definition Supply Current IDD Quiescent (Note 5) ISS Quiescent (Note 5) VDD Supply VSS Supply Current Required From Positive Supply During Operation Current Required From Negative Supply During Operation Operating Range of Positive Supply Operating Range of Negative Supply Reference Voltage VREF –VSS Range of Voltage Reference Input Accuracy Nonlinearity (Note 10) Input Frequency Range (Note 7 and 8) Frequency Input Positive Excursion Negative Excursion Minimum Positive Pulse Width (Note 8) Minimum Negative Pulse Width (Note 8) Deviation From Ideal Transfer Function as a Percentage Full-Scale Voltage Frequency Range for Specified Nonlinearity Voltage Required to Turn Threshold Detector On Voltage Required to Turn Threshold Detector Off Time Between Threshold Crossings Time Between Threshold Crossings Input Impedance Analog Outputs Output Voltage (Note 9) Output Loading Voltage Range of Op Amp Output for Specified Nonlinearity Resistive Loading at Output of Op Amp Supply Current IDD Quiescent (Note 10) ISS Quiescent (Note 10) VDD Supply VSS Supply Current Required From Positive Supply During Operation Current Required From Negative Supply During Operation Operating Range of Positive Supply Operating Range of Negative Supply Reference Voltage VREF –VSS Range of Voltage Reference Input NOTES: 1. 2. 3. 4. 5. Full temperature range. Guaranteed, Not Tested. IIN = 0. Full temperature range, IOUT = 10mA. IOUT = 10µA. Threshold Detect = 5V, Amp Out = 0V, Full Temperature Range TELCOM SEMICONDUCTOR, INC. TC9401 TC9400 TC9402 Min Typ Max Min Typ Max Min Typ Max — 1.5 — 4 –4 6 — 1.5 6 – 1.5 – 6 — – 1.5 – 6 — 7.5 4 — 7.5 — – 7.5 – 4 — – 7.5 — — 3 10 mA 4 –4 –3 — — – 10 7.5 – 7.5 mA V V – 2.5 — — V — 0.05 0.25 % Full Scale — — – 2.5 — 0.01 0.02 — 10 — 100k 10 — 100k 10 — 100k Hz 0.4 — VDD 0.4 — VDD 0.4 — VDD V – 2 – 0.4 — –2 – 0.4 — –2 V — µsec 0.02 0.05 — 5 — — 5 — — 5 — 0.5 — — 0.5 — — 0.5 — 10 — — 10 — — 10 — VDD – 1 — — VDD – 1 — 2 — — 2 — — 1.5 6 — 1.5 — 4 –4 – 2.5 MΩ — VDD – 1 — V — 2 — — kΩ 6 — 3 10 mA – 10 7.5 – 7.5 mA V V — — – 2.5 — — V — –3 4 — –4 — – 2.5 — 3 4 5 µsec — – 1.5 – 6 – 1.5 – 6 — 7.5 4 — 7.5 — – 7.5 – 4 — – 7.5 2 Unit – 2.5 – 0.4 — 1 6 6. 10Hz to 100kHz.; Guaranteed, Not Tested 7. 5µsec minimum positive pulse width and 0.5 µsec minimum negative pulse width. 8. tR = tF = 20 nsec. 9. RL ≥ 2kΩ.; Tested @ 10kΩ 10. Full temperature range, VIN = – 0.1V. 7 8 3-289 VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 PIN CONFIGURATIONS 14-Pin Plastic DIP/CerDIP IBIAS 1 14-Pin SOIC (Narrow) IBIAS 1 14 VDD ZERO ADJ 2 13 NC 12 AMPLIFIER OUT 11 THRESHOLD DETECTOR 10 FREQ/2 OUT 14 VDD ZERO ADJ 2 13 NC IIN 3 I IN 12 AMPLIFIER OUT TC9400 TC9401 TC9402 VSS 4 VREF OUT 5 V 11 THRESHOLD DETECTOR 10 FREQ/2 OUT GND 6 9 OUTPUT COMMON VREF 7 8 PULSE FREQ OUT V REF 3 TC9400 TC9401 TC9402 SS 4 OUT 5 GND 6 9 OUTPUT COMMON 7 8 PULSE FREQ OUT V REF NC = NO INTERNAL CONNECTION PIN DESCRIPTIONS Pin No. 3-290 Symbol Description 1 IBIAS This pin sets bias current in the TC9400. Connect to VSS through a 100 kΩ resistor. See text. 2 Zero Adj 3 IIN 4 VSS 5 VREFOUT 6 GND Analog ground. 7 VREF Voltage reference input, typically – 5V. 8 Pulse Freq Out 9 Output Common 10 Freq/2 Out This open drain output is a square wave at one half the frequency of the pulse output (pin 8). Output transitions of this pin occur on the rising edge of pin 8. 11 Threshold Detect Input to the threshold detector. This pin is the frequency input during F/V operation. 12 Amplifier Out 13 NC No internal connection 14 VDD Positive power supply connection, typically +5V. Low frequency adjustment input. See text. Input current connection for the V/F converter. Negative power supply voltage connection, typically – 5V. Reference capacitor connection. Frequency output. This open drain output will pulse LOW each time the Freq threshold detector limit is reached. The pulse rate is proportional to input voltage. Source connection for the open drain output FETs. See text. Output of the integrator amplifier. TELCOM SEMICONDUCTOR, INC. VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 +5V 2 +5V 14 VDD 11 fOUT 8 THRESHOLD DETECT 1 RL 10kΩ 3µsec DELAY +5V THRESHOLD DETECTOR fOUT/2 10 SELFSTART ÷2 9 OUTPUT COMMON –3V 12 5 4 VREF OUT CREF 180pF RIN 1MΩ VIN 0V –10V AMP OUT 20kΩ CINT 820pF INPUT 510kΩ 12pF 3 IIN 2 ZERO ADJUST +5V – OpAmp 5 + IBIAS –5V 10kΩ TC9400 TC9401 TC9402 60pF 50kΩ OFFSET ADJUST 3 RL 10kΩ 1 VSS VREF 4 7 GND 6 RBIAS 100kΩ REFERENCE VOLTAGE (TYPICALLY –5V) –5V Figure 1. 6 10 Hz to 10 kHz V/F Converter VOLTAGE-TO-FREQUENCY (V/F) CIRCUIT DESCRIPTION The TC9400 V/F converter operates on the principal of charge balancing. The operation of the TC9400 is easily understood by referring to Figure 1. The input voltage (VIN) is converted to a current (IIN) by the input resistor. This current is then converted to a charge on the integrating capacitor and shows up as a linearly decreasing voltage at the output of the op amp. The lower limit of the output swing is set by the threshold detector, which causes the reference voltage to be applied to the reference capacitor for a time period long enough to charge the capacitor to the reference voltage. This action reduces the charge on the integrating capacitor by a fixed amount (q = CREF × VREF), causing the op amp output to step up a finite amount. TELCOM SEMICONDUCTOR, INC. At the end of the charging period, CREF is shorted out. This dissipates the charge stored on the reference capacitor, so that when the output again crosses zero the system is ready to recycle. In this manner, the continued discharging of the integrating capacitor by the input is balanced out by fixed charges from the reference voltage. As the input voltage is increased, the number of reference pulses required to maintain balance increases, which causes the output frequency to also increase. Since each charge increment is fixed, the increase in frequency with voltage is linear. In addition, the accuracy of the output pulse width does not directly affect the linearity of the V/F. The pulse must simply be long enough for full charge transfer to take place. 3-291 7 8 VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 3 µsec TYP fOUT fOUT/2 1/f VREF CREF CINT 0V AMP OUT NOTES: 1. To adjust fMIN, set VIN = 10mV and adjust the 50kΩ offset for 10Hz output. 2. To adjust fMAX, set VIN = 10V and adjust RIN or VREF for 10 kHz output. 3. To increase fOUT MAX to 100kHz, change CREF to 2pF and CINT to 75pF. 4. For high-performance applications, use high-stability components for RIN, CREF, VREF (metal film resistors and glass capacitors). Also, separate output ground (pin 9) from input ground (pin 6). Figure 2 . Output Waveforms The TC9400 contains a "self-start" circuit to ensure the V/F converter always operates properly when power is first applied. In the event that, during power-on, the Op Amp output is below the threshold and CREF is already charged, a positive voltage step will not occur. The op-amp output will continue to decrease until it crosses the –3.0V threshold of the "self-start" comparator. When this happens, an internal resistor is connected to the op-amp input, which forces the output to go positive until the TC9400 is in its normal operating mode. The TC9400 utilizes low power CMOS processing for low input bias and offset currents with very low power dissipation. The open-drain N-channel output FETs provide high voltage and high current sink capability. PIN FUNCTIONS Threshold Detector Input VOLTAGE-TO-TIME MEASUREMENTS Pulse Freq Out The TC9400 output can be measured in the time domain as well as the frequency domain. Some microcomputers, for example, have extensive timing capability but limited counter capability. Also, the response time of a time domain measurement is only the period between two output pulses, while the frequency measurement must accumulate pulses during the entire counter timebase period. Time measurements can be made from either the TC9400's Pulse Freq Out output or from the Freq/2 output. The Freq/2 output changes state on the rising edge of Pulse Freq Out, so Freq/2 is a symmetrical square wave at one half the pulse output frequency. Timing measurements can therefore be made between successive Pulse Freq Out pulses, or while Freq/2 is high (or low). This output is an open-drain N-channel FET which provides a pulse waveform whose frequency is proportional to the input voltage. This output requires a pull-up resistor and interfaces directly with MOS, CMOS, and TTL logic. 3-292 In the V/F mode, this input is connected to the amplifier output (pin 12) and triggers a 3 µsec pulse when the input voltage passes through its threshold. In the F/V mode, the input frequency is applied to this input. The nominal threshold of the detector is halfway between the power supplies, or (VDD + VSS)/2 ±400mV. The TC9400's charge balancing V/F technique is not dependent on a precision comparator threshold, because the threshold only sets the lower limit of the op-amp output. The op-amp's peak-to-peak output swing, which determines the frequency, is only influenced by external capacitors and by VREF. Freq/2 Out This output is an open-drain N-channel FET which provides a square wave one-half the frequency of the pulse frequency output. The Freq/2 output will change state on the rising edge of Pulse Freq Out. This output requires a pullup resistor and interfaces directly with MOS, CMOS, and TTL logic. TELCOM SEMICONDUCTOR, INC. VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 Output Common VREF Out The sources of both the Freq/2 out and the Pulse Freq Out are connected to this pin. An output level swing from the drain voltage to ground or to the VSS supply may be obtained by connecting this pin to the appropriate point. The charging current for CREF is supplied through this pin. When the op amp output reaches the threshold level, this pin is internally connected to the reference voltage and a charge, equal to VREF x CREF, is removed from the integrator capacitor. After about 3 µsec, this pin is internally connected to the summing junction of the op amp to discharge CREF. Break-before-make switching ensures that the reference voltage is not directly applied to the summing junction. RBIAS An external resistor, connected to VSS, sets the bias point for the TC9400. Specifications for the TC9400 are based on RBIAS = 100kΩ ±10%, unless otherwise noted. Increasing the maximum frequency of the TC9400 beyond 100kHz is limited by the pulse width of the Pulse Output (typically 3µsec). Reducing RBIAS will decrease the pulse width and increase the maximum operating frequency, but linearity errors will also increase. RBIAS can be reduced to 20kΩ, which will typically produce a maximum full scale frequency of 500kHz. This pin is the noninverting input of the operational amplifier. The low-frequency set point is determined by adjusting the voltage at this pin. IIN The inverting input of the operational amplifier and the summing junction when connected in the V/F mode. An input current of 10µA is specified, but an overrange current up to 50µA can be used without detrimental effect to the circuit operation. IIN connects the summing junction of an operational amplifier. Voltage sources cannot be attached directly, but must be buffered by external resistors. VREF A reference voltage from either a precision source or the VSS supply is applied to this pin. Accuracy of the TC9400 is dependent on the voltage regulation and temperature characteristics of the reference circuitry. Since the TC9400 is a charge balancing V/F converter, the reference current will be equal to the input current. For this reason, the DC impedance of the reference voltage source must be kept low enough to prevent linearity errors. For linearity of 0.01%, a reference impedance of 200Ω or less is recommended. A 0.1µF bypass capacitor should be connected from VREF to ground. TELCOM SEMICONDUCTOR, INC. 3 The output frequency (fOUT) is related to the analog input voltage (VIN) by the transfer equation: Amplifier Out Zero Adjust 2 V/F CONVERTER DESIGN INFORMATION Input/Output Relationships Frequency out = The output stage of the operational amplifier. During V/F operation, a negative-going ramp signal is available at this pin. In the F/V mode, a voltage proportional to the frequency input is generated. 1 VIN 1 × RIN (VREF) (CREF) 4 External Component Selection RIN The value of this component is chosen to give a fullscale input current of approximately 10µA: 5 RIN ≅ VIN Full Scale . 10µA Example: RIN ≅ 10V = 1MΩ. 10µA Note that the value is an approximation and the exact relationship is defined by the transfer equation. In practice, the value of RIN typically would be trimmed to obtain fullscale frequency at VIN full scale (see "Adjustment Procedure"). Metal film resistors with 1% tolerance or better are recommended for high-accuracy applications because of their thermal stability and low-noise generation. 6 CINT The exact value is not critical but is related to CREF by the relationship: 7 3CREF ≤ CINT ≤ 10 CREF. Improved stability and linearity are obtained when CINT ≤ 4CREF. Low-leakage types are recommended, although mica and ceramic devices can be used in applications where their temperature limits are not exceeded. Locate as close as possible to pins 12 and 13. 8 3-293 VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 CREF The exact value is not critical and may be used to trim the full-scale frequency (see "Input/Output Relationships"). Glass film or air trimmer capacitors are recommended because of their stability and low leakage. Locate as close as possible to pins 5 and 3. VDD, VSS Power supplies of ±5V are recommended. For highaccuracy requirements, 0.05% line and load regulation and 0.1µF disc decoupling capacitors located near the pins are recommended. Adjustment Procedure Figure 1 shows a circuit for trimming the zero location. Full scale may be trimmed by adjusting RIN, VREF, or CREF. Recommended procedure for a 10kHz full-scale frequency is as follows: (1) Set VIN to 10 mV and trim the zero adjust circuit to obtain a 10Hz output frequency. Improved Single Supply V/F Converter Operation A TC9400 which operates from a single 12 to 15V variable power source is shown in Figure 5. This circuit uses two Zener diodes to set stable biasing levels for the TC9400. The Zener diodes also provide the reference voltage, so the output impedance and temperature coefficient of the Zeners will directly affect power supply rejection and temperature performance. Full scale adjustment is accomplished by trimming the input current. Trimming the reference voltage is not recommended for high accuracy applications unless an op amp is used as a buffer, because the TC9400 requires a low impedance reference (see the VREF pin description section for more information). The circuit of Figure 5 will directly interface with CMOS logic operating at 12V to 15V. TTL or 5V CMOS logic can be accommodated by connecting the output pullup resistors to the +5V supply. An optoisolator can also be used if an isolated output is required. (2) Set VIN to 10V and trim either RIN, VREF, or CREF to obtain a 10kHz output frequency. If adjustments are performed in this order, there should be no interaction and they should not have to be repeated. 500 VDD = +5V VSS = – 5V RIN = 1MΩ VIN = +10V TA = +25°C CREF (pF) +12pF 400 300 1 kHz 200 100 100kHz 0 –1 Figure 3. 3-294 –2 –3 –4 VREF (V) –5 –6 –7 Recommended CREF vs VREF TELCOM SEMICONDUCTOR, INC. VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 V+ = 8V TO 15V (FIXED) R2 0.9 R1 GAIN ADJUST OFFSET ADJUST RIN 1MΩ 2 14 V2 10kΩ 2 6 5V 8 8.2 kΩ 0.01 µF 2 kΩ 7 VREF 11 0.01 µF 0.2 R1 fOUT 10kΩ 10 fOUT/2 3 TC9400 12 5 820 pF 1 180 pF 3 IIN VIN 0V–10V IIN 1 4 9 100 kΩ R1 R2 V+ 10V 1 MΩ 10kΩ 12V 1.4 MΩ 14kΩ 15V 2 MΩ 20kΩ 4 1 fOUT = IIN × (V2–V7) (CREF) (VIN–V2) (V+–V2) + IIN= RIN (0.9 R1+0.2 R1) 5 Figure 4 . Fixed Voltage — Single Supply Operation +12 to +15V 1.2k* 14 VDD 1µF R1 910k R4 100k CINT D2 5.1VZ 11 THRESHOLD DETECT 12 AMP OUT CREF 5 CREF R3 GAIN TC9400 3 IIN 2 ZERO ADJUST 6 GND 100k R2 910k INPUT VOLTAGE (0 to 10V) 10k R5 91k D1 5.1VZ 0.1µ 7 V REF 1 I BIAS Rp OFFSET 20k 100k 10k 6 fOUT 8 fOUT/2 10 OUTPUT FREQUENCY OUTPUT 9 COMMON VSS 4 7 DIGITAL GROUND ANALOG GROUND COMPONENT SELECTION F/S FREQ. 1 kHz 10 kHz 100 kHz CREF 2200pF 180pF 27pF CINT 4700pF 470pF 75pF Figure 5. TELCOM SEMICONDUCTOR, INC. 8 Voltage to Frequency 3-295 VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 Input Voltage Levels FREQUENCY-TO-VOLTAGE (F/V) CIRCUIT DESCRIPTION When used as an F/V converter, the TC9400 generates an output voltage linearly proportional to the input frequency waveform. Each zero crossing at the threshold detector's input causes a precise amount of charge (q = CREF × VREF) to be dispensed into the op amp's summing junction. This charge in turn flows through the feedback resistor, generating voltage pulses at the output of the op amp. A capacitor (CINT) across RINT averages these pulses into a DC voltage which is linearly proportional to the input frequency. F/V CONVERTER DESIGN INFORMATION Input/Output Relationships The output voltage is related to the input frequency (fIN) by the transfer equation: VOUT = [VREF CREF RINT] fIN. The response time to a change in fIN is equal to (RINT CINT). The amount of ripple on VOUT is inversely proportional to CINT and the input frequency. CINT can be increased to lower the ripple. Values of 1µF to 100µF are perfectly acceptable for low frequencies. When the TC9400 is used in the single-supply mode, VREF is defined as the voltage difference between pin 7 and pin 2. The input frequency is applied to the Threshold Detector input (Pin 11). As discussed in the V/F circuit section of this data sheet, the threshold of pin 11 is approximately (VDD + VSS) /2 ±400mV. Pin 11's input voltage range extends from VDD to about 2.5 V below the threshold. If the voltage on pin 11 goes more than 2.5 volts below the threshold, the V/F mode startup comparator will turn on and corrupt the output voltage. The Threshold Detector input has about 200 mV of hysteresis. In ±5 V applications, the input voltage levels for the TC9400 are ±400mV, minimum. If the frequency source being measured is unipolar, such as TTL or CMOS operating from a +5V source, then an AC coupled level shifter should be used. One such circuit is shown in Figure 6a. The level shifter circuit in Figure 6b can be used in single supply F/V applications. The resistor divider ensures that the input threshold will track the supply voltages. The diode clamp prevents the input from going far enough in the negative direction to turn on the startup comparator. The diode's forward voltage decreases by 2.1 mV/°C, so for high ambient temperature operation two diodes in series are recommended. +8V to +5V +5V 14 VDD 14 VDD 10k Frequency Input +5V 33k TC9400 0.01µF 11 IN914 Frequency Input DET 1.0M 33k +5V 0V TC9400 0.01µF 11 IN914 DET 1.0M 0V GND VSS 6 4 0.1µF 10k VSS 4 –5V (A) ±5V Supply (B) Single Supply Figure 6. 3-296 Frequency Input Level Shifter TELCOM SEMICONDUCTOR, INC. VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 1 2 +5V V+ 14 VDD TC9400A TC9401A TC9402A * fOUT/2 10 42 OUTPUT COMMON 9 * SEE FIGURE 6 fIN THRESHOLD DETECT 11 V+ 3 * fOUT 8 3 µsec DELAY * OPTIONAL IF BUFFER IS NEEDED THRESHOLD DETECTOR 4 VREF OUT 5 CREF 56 pF 12pF IIN 3 60pF 100kΩ 2 kΩ 2.2kΩ – OP AMP + 2 ZERO ADJUST IBIAS VSS 1 4 VREF AMP OUT 12 RINT 1 MΩ + OFFSET ADJUST +5V SEE EQUATION, PAGE 12 CINT 1000pF VO 5 GND 7 6 10 kΩ VREF –5V 6 (TYPICALLY –5V) Figure 7. DC — 10 kHz F/V Converter Input Buffer 0.5µsec MIN 5.0µsec MIN INPUT fOUT DELAY = 3µsec fOUT and fOUT/2 are not used in the F/V mode. However, these outputs may be useful for some applications, such as a buffer to feed additional circuitry. Then, fOUT will follow the input frequency waveform, except that fOUT will go high 3µsec after fIN goes high; fOUT/2 will be squarewave with a frequency of one-half fOUT. If these outputs are not used, pins 8, 9 and 10 should be connected to ground. 7 fOUT/2 8 Figure 8 . F/V Digital Outputs TELCOM SEMICONDUCTOR, INC. 3-297 VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 V+ = 10V to 15V 14 VDD 10k 6 GND .01µF 6.2V 10k TC9400 500k 2 ZERO ADJUST 100k 33k 5 47pF V+ Offset Adjust Frequency Input VREFOUT 3 IIN 1M 0.01µF 11 DET GND IN914 0.1µF .001µF AMP OUT 12 1.0k 1.0M IBIAS VOUT 6 VREF VSS 7 4 1.0k 100k Note: The output is referenced to pin 6, which is at 6.2V (Vz). For frequency meter applications, a 1 mA meter with a series-scaling resistor can be placed across pins 6 and 12. Figure 9. F/V Single Supply F/V Converter Output Filtering The output of the TC9400 has a sawtooth ripple superimposed on a DC level. The ripple will be rejected if the TC9400 output is converted to a digital value by an integrating analog to digital converter, such as the TC7107 or TC7109. The ripple can also be reduced by increasing the value of the integrating capacitor, although this will reduce the response time of the F/V converter. The sawtooth ripple on the output of an F/V can be eliminated without affecting the F/V's response time by using the circuit in Figure 10. The circuit is a capacitance multiplier, where the output coupling capacitor is multiplied by the AC gain of the op amp. A moderately fast op amp, such as the TL071, should be used. VREFOUT 5 47pF IIN 3 TC9400 1M .001µF 200 AMP OUT 12 0.1µF 1M .01µF GND 6 +5 2 3 1M – VOUT 7 6 TL071 + 4 –5 Figure 10. 3-298 Ripple Filter TELCOM SEMICONDUCTOR, INC. VOLTAGE-TO-FREQUENCY/ FREQUENCY-TO-VOLTAGE CONVERTERS TC9400 TC9401 TC9402 F/V POWER-ON RESET In some cases, however, the TC9400 output must be zero at power-on without a frequency input. In such cases, a capacitor connected from pin 11 to VDD will usually be sufficient to pulse the TC9400 and provide a power-on reset (see Figure 11A). Where predictable power-on operation is critical, a more complicated circuit, such as Figure 11B, may be required. In F/V mode, the TC9400 output voltage will occasionally be at its maximum value when power is first applied. This condition remains until the first pulse is applied to fIN. In most frequency-measurement applications this is not a problem, because proper operation begins as soon as the frequency input is applied. 1 2 3 VDD 14 1000pF 1kΩ 11 fIN THRESHOLD DETECTOR (A) 4 TC9400 VDD (B) 16 3 VCC CLRA 100kΩ 5 B 2 R 1 C 5 CD4538 4 Q 6 To TC 9400 A 1µF VSS 8 Figure 11. fIN 6 Power-On Operation/Reset 7 8 TELCOM SEMICONDUCTOR, INC. 3-299