TI SN74ACT7814

SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
D
D
D
D
D
D
D
D
D
D
D
Member of the Texas Instruments
Widebus Family
Load Clock and Unload Clock Can Be
Asynchronous or Coincident
64 Words by 18 Bits
Low-Power Advanced CMOS Technology
Full, Empty, and Half-Full Flags
Programmable Almost-Full/Almost-Empty
Flag
Fast Access Times of 15 ns With a 50-pF
Load and All Data Outputs Switching
Simultaneously
Data Rates up to 50 MHz
3-State Outputs
Pin-to-Pin Compatible With SN74ACT7804
and SN74ACT7806
Packaged in Shrink Small-Outline 300-mil
Package Using 25-mil Center-to-Center
Spacing
description
A FIFO memory is a storage device that allows
data to be written into and read from its array at
independent data rates. The SN74ACT7814 is a
64-word by 18-bit FIFO for high speed and fast
access times. It processes data at rates up to
50 MHz and access times of 15 ns in a bit-parallel
format.
DL PACKAGE
(TOP VIEW)
RESET
D17
D16
D15
D14
D13
D12
D11
D10
VCC
D9
D8
GND
D7
D6
D5
D4
D3
D2
D1
D0
HF
PEN
AF/AE
LDCK
NC
NC
FULL
1
56
2
55
3
54
4
53
5
52
6
51
7
50
8
49
9
48
10
47
11
46
12
45
13
44
14
43
15
42
16
41
17
40
18
39
19
38
20
37
21
36
22
35
23
34
24
33
25
32
26
31
27
30
28
29
OE
Q17
Q16
Q15
GND
Q14
VCC
Q13
Q12
Q11
Q10
Q9
GND
Q8
Q7
Q6
Q5
VCC
Q4
Q3
Q2
GND
Q1
Q0
UNCK
NC
NC
EMPTY
Data is written into memory on a low-to-high
transition at the load clock (LDCK) input and is
read out on a low-to-high transition at the unload
clock (UNCK) input. The memory is full when the
number of words clocked in exceeds the number
of words clocked out by 64. When the memory is
full, LDCK signals have no effect on the data
residing in memory. When the memory is empty,
UNCK signals have no effect.
Status of the FIFO memory is monitored by the full (FULL), empty (EMPTY), half-full (HF), and
almost-full/almost-empty (AF/AE) flags. The FULL output is low when the memory is full and high when the
memory is not full. The EMPTY output is low when the memory is empty and high when it is not empty. The HF
output is high when the FIFO contains 32 or more words and is low when it contains 31 or fewer words. The
AF/AE status flag is a programmable flag. The first one or two low-to-high transitions of LDCK after reset are
used to program the almost-empty offset value (X) and the almost-full offset value (Y) if program enable (PEN)
is low. The AF/AE flag is high when the FIFO contains X or fewer words or (64 – Y) or more words. The AF/AE
flag is low when the FIFO contains between (X + 1) and (63 – Y) words.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments Incorporated.
Copyright  1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
description (continued)
A low level on the reset (RESET) input resets the internal stack pointers and sets FULL high, HF low, and
EMPTY low. The Q outputs are not reset to any specific logic level. The FIFO must be reset upon power up.
The first word loaded into empty memory causes EMPTY to go high and the data to appear on the Q outputs.
It is important to note that the first word does not have to be unloaded. The data outputs are noninverting with
respect to the data inputs and are in the high-impedance state when the output-enable (OE) input is high.
The SN74ACT7814 is characterized for operation from 0°C to 70°C.
logic symbol†
Φ
FIFO 64 × 18
SN74ACT7814
RESET
LDCK
UNCK
OE
PEN
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
1
RESET
25
32
56
23
21
FULL
LDCK
HALF-FULL
UNCK
ALMOST FULL/EMPTY
EN1
EMPTY
22
24
29
FULL
HF
AF/AE
EMPTY
PROGRAM ENABLE
0
0
33
20
34
19
36
18
37
17
38
16
40
15
41
14
42
12
43
11
45
Data
Data
1
9
46
8
47
7
48
6
49
5
51
4
53
3
54
2
55
17
17
† This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
28
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q11
Q12
Q13
Q14
Q15
Q16
Q17
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
functional block diagram
OE
D0–D17
Location 1
Location 2
Read
Pointer
UNCK
64 × 18 SRAM
Write
Pointer
LDCK
Location 63
Location 64
Q0–Q17
EMPTY
Reset
Logic
RESET
StatusFlag
Logic
PEN
FULL
HF
AF/AE
Terminal Functions
TERMINAL
I/O
DESCRIPTION
24
O
Almost-full/almost-empty flag. Depth-offset values can be programmed for AF/AE, or the default value
of 8 can be used for both the almost-empty offset (X) and the almost-full offset (Y). AF/AE is high when
memory contains X or fewer words or (64 – Y) or more words. AF/AE is high after reset.
D0–D17
2–9, 11–12,
14–21
I
18-bit data input port
EMPTY
29
O
Empty flag. EMPTY is high when the FIFO memory is not empty; EMPTY is low when the FIFO memory
is empty or upon assertion of RESET.
FULL
28
O
Full flag. FULL is high when the FIFO memory is not full or upon assertion of RESET; FULL is low when
the FIFO memory is full.
HF
22
O
Half-full flag. HF is high when the FIFO memory contains 32 or more words. HF is low after reset.
LDCK
25
I
Load clock. Data is written to the FIFO on the rising edge of LDCK when FULL is high.
OE
56
I
Output enable. When OE is high, the data outputs are in the high-impedance state.
PEN
23
I
Program enable. After reset and before the first word is written to the FIFO, the binary value on D0–D4
is latched as an AF/AE offset value when PEN is low and WRTCLK is high.
Q0–Q17
33–34, 36–38,
40–43, 45–49,
51, 53–55
O
18-bit data output port
RESET
1
I
Reset. A low level on RESET resets the FIFO and drives FULL high and HF and EMPTY low.
UNCK
32
I
Unload clock. Data is read from the FIFO on the rising edge of UNCK when EMPTY is high.
NAME
NO.
AF/AE
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
offset values for AF/AE
The AF/AE flag has two programmable limits: the almost-empty offset value (X) and the almost-full offset
value (Y). They can be programmed after the FIFO is reset and before the first word is written to memory. The
AF/AE flag is high when the FIFO contains X or fewer words or (64 – Y) or more words.
To program the offset values, PEN can be brought low after reset only when LDCK is low. On the following
low-to-high transition of LDCK, the binary value on D0–D4 is stored as the almost-empty offset value (X) and
the almost-full offset value (Y). Holding PEN low for another low-to-high transition of LDCK reprograms Y to the
binary value on D0–D4 at the time of the second LDCK low-to-high transition. Writes to the FIFO memory are
disabled while the offsets are programmed. A maximum value of 31 can be programmed for either X or Y (see
Figure 1). To use the default values of X = Y = 8, PEN must be held high.
RESET
LDCK
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
Don’t Care
PEN
ÏÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏÏ
ÌÌÌÌÌ
ÌÌÌÌÌ
D0–D4
Don’t Care
X and Y
Y
EMPTY
Figure 1. Programming X and Y Separately
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
RESET
1
0
PEN
ÏÏ
ÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏ
ÏÏ
ÏÏÏÏ
ÏÏÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
LDCK
D0–D17
W1
W2
W
(X+1)
W32
W
(64–Y)
Don’t Care
W64
POST OFFICE BOX 655303
UNCK
1
0
W2
W
(Y+1)
W
(Y+2)
W33
W34
W
(64–X)
W
(65–X)
W63
ÏÏ
ÏÏ
ÏÏ
ÏÏ
W1
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
• DALLAS, TEXAS 75265
Q0–Q17
W64
EMPTY
AF/AE
HF
Define the AF/AE Flag Using
the Default Value of X and Y
Figure 2. Write, Read, and Flag Timing Reference
Figure 2
5
SCAS209C – APRIL 1992 – REVISED APRIL 1998
FULL
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
OE
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
Voltage range applied to a disabled 3-state output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V
Package thermal impedance, θJA (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The package thermal impedance is calculated in accordance with JESD 51.
recommended operating conditions
’ACT7814-20
VCC
VIH
Supply voltage
VIL
IOH
Low-level input voltage
High-level input voltage
Low level output current
Low-level
TA
Operating free-air temperature
’ACT7814-40
MAX
MIN
MAX
MIN
MAX
4.5
5.5
4.5
5.5
4.5
5.5
2
High-level output current
IOL
’ACT7814-25
MIN
2
2
UNIT
V
V
0.8
0.8
0.8
V
Q outputs, flags
–8
–8
–8
mA
Q outputs
16
16
16
8
8
8
Flags
0
70
0
70
0
70
mA
°C
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VOH
VOL
II
IOZ
ICC
∆ICC§
Ci
Flags
Q outputs
TEST CONDITIONS
VCC = 4.5 V,
VCC = 4.5 V,
IOH = –8 mA
IOL = 8 mA
VCC = 4.5 V,
VCC = 5.5 V,
IOL = 16 mA
VI =VCC or 0
MIN
TYP‡
One input at 3.4 V,
UNIT
V
0.5
0.5
VCC = 5.5 V,
VO =VCC or 0
VI = VCC – 0.2 V or 0
VCC = 5.5 V,
VI = 0,
MAX
2.4
Other inputs at VCC or GND
V
±5
µA
±5
µA
400
µA
1
mA
f = 1 MHz
4
pF
VO = 0,
f = 1 MHz
‡ All typical values are at VCC = 5 V, TA = 25°C.
§ This is the supply current for each input that is at one of the specified TTL voltage levels rather 0 V or VCC.
8
pF
Co
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
timing requirements over recommended operating conditions (see Figures 1 through 3)
’ACT7814-20
MIN
fclock
tw
Clock frequency
MIN
Setup time
Hold time
MAX
’ACT7814-40
MIN
40
MAX
25
LDCK high or low
7
8
12
UNCK high or low
7
8
12
PEN low
7
8
12
10
10
12
RESET low
th
’ACT7814-25
50
Pulse duration
tsu
MAX
D0–D17 before LDCK↑
5
5
5
PEN before LDCK↑
5
5
5
LDCK inactive before RESET high
5
6
6
D0–D17 after LDCK↑
0
0
0
LDCK inactive after RESET high
5
6
6
PEN low after LDCK↑
3
3
3
PEN high after LDCK↓
0
0
0
UNIT
MHz
ns
ns
ns
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 50 pF (unless otherwise noted) (see Figure 3)
PARAMETER
FROM
(INPUT)
fmax
LDCK or UNCK
tpd
d
TO
(OUTPUT)
LDCK↑
Any Q
UNCK↑
tpd‡
UNCK↑
Any Q
tPLH
LDCK↑
EMPTY
tPHL
RESET low
UNCK↑
EMPTY
LDCK↑
tPLH
tpd
d
FULL
UNCK↑
FULL
RESET low
LDCK↑
AF/AE
UNCK↑
’ACT7814-20
TYP†
MAX
’ACT7814-25
MIN
MIN
50
40
9
6
11.5
MAX
’ACT7814-40
MIN
MAX
25
UNIT
MHz
20
9
22
9
24
15
6
18
6
20
10.5
ns
ns
6
15
6
17
6
19
6
15
6
17
6
19
4
16
4
18
4
20
6
15
6
17
6
19
6
15
6
17
6
19
4
18
4
20
4
22
7
18
7
20
7
22
7
18
7
20
7
22
ns
ns
ns
ns
RESET low
AF/AE
2
10
2
12
2
14
LDCK↑
HF
5
18
5
20
5
22
7
18
7
20
7
22
3
12
3
14
3
16
Any Q
2
9
2
10
2
11
ns
tdis
Any Q
OE
† All typical values are at VCC = 5 V, TA = 25°C.
‡ This parameter is measured at CL = 30 pF (see Figure 4).
2
10
2
11
2
12
ns
tPLH
tPHL
ten
UNCK↑
HF
RESET low
OE
ns
ns
operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
Cpd
Power dissipation capacitance per FIFO channel
POST OFFICE BOX 655303
TEST CONDITIONS
Outputs enabled
• DALLAS, TEXAS 75265
CL = 50 pF,
f = 5 MHz
TYP
53
UNIT
pF
7
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
PARAMETER MEASUREMENT INFORMATION
7V
PARAMETER
S1
500 Ω
From Output
Under Test
ten
Test
Point
CL = 50 pF
(see Note A)
tdis
500 Ω
S1
tPZH
tPZL
tPHZ
tPLZ
tPLH
tPHL
tpd
LOAD CIRCUIT
Open
Closed
Open
Closed
Open
Open
tw
3V
3V
Timing
Input
Input
VOLTAGE WAVEFORMS
PULSE DURATION
th
3V
Data
Input
1.5 V
1.5 V
0V
3V
Output
Control
tPZL
3V
1.5 V
1.5 V
0V
tPLH
1.5 V
VOL
Output
Waveform 2
S1 at Open
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOL + 0.3 V
VOH
VOH – 0.3 V
≈0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
Figure 3. Load Circuit and Voltage Waveforms
• DALLAS, TEXAS 75265
VOL
tPHZ
1.5 V
NOTE A: CL includes probe and jig capacitance.
POST OFFICE BOX 655303
tPLZ
1.5 V
tPZH
VOH
8
1.5 V
≈ 3.5 V
Output
Waveform 1
S1 at 7 V
tPHL
1.5 V
1.5 V
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
Output
1.5 V
0V
0V
tsu
Input
1.5 V
1.5 V
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
TYPICAL CHARACTERISTICS
PROPAGATION DELAY TIME
vs
LOAD CAPACITANCE
SUPPLY CURRENT
vs
CLOCK FREQUENCY
200
VCC = 5 V
TA = 25°C
RL = 500 Ω
TA = 75°C
CL = 0 pF
180
typ + 6
VCC = 5.5 V
160
I CC(f) – Supply Current – mA
t pd – Propagation Delay Time – ns
typ + 8
typ + 4
typ + 2
typ
VCC = 5 V
140
120
100
VCC = 4.5 V
80
60
40
20
0
typ – 2
0
50
100
150
200
250
300
0
10
20
30
40
50
60
70
fclock – Clock Frequency – MHz
CL – Load Capacitance – pF
Figure 4
Figure 5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN74ACT7814
64 × 18 STROBED FIRST-IN, FIRST-OUT MEMORY
SCAS209C – APRIL 1992 – REVISED APRIL 1998
APPLICATION INFORMATION
LDCK
SN74ACT7814
LDCK
UNCK
FULL
EMPTY
FULL
OE
D18–D35
D0–D17
Q0–Q17
UNCK
EMPTY
OE
Q18–Q35
SN74ACT7814
LDCK
UNCK
FULL
EMPTY
OE
D0–D17
D0–D17
Q0–Q17
Figure 6. Word-Width Expansion: 64 × 36 Bits
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
Q0–Q17
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated