TI 74GTL16622ADGGRE4

www.ti.com
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
FEATURES
•
•
•
•
•
•
•
•
•
•
Member of Texas Instruments Widebus™
Family
OEC™ Circuitry Improves Signal Integrity and
Reduces Electromagnetic Interference
D-Type Flip-Flops With Qualified Storage
Enable
Translates Between GTL/GTL+ Signal Levels
and LVTTL Logic Levels
Supports Mixed-Mode (3.3 V and 5 V) Signal
Operation on A-Port and Control Inputs
Ioff Supports Partial-Power-Down Mode
Operation
Bus Hold on Data Inputs Eliminates the Need
for External Pullup/Pulldown Resistors on
A Port
Distributed VCC and GND Pins Minimize
High-Speed Noise
Latch-Up Performance Exceeds 250 mA Per
JESD 17
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
DESCRIPTION/ORDERING INFORMATION
The SN74GTL16622A is an 18-bit registered bus
transceiver that provides LVTTL-to-GTL/GTL+ and
GTL/GTL+-to-LVTTL signal-level translation. This
device is partitioned as two separate 9-bit
transceivers with individual clock-enable controls and
contains D-type flip-flops for temporary storage of
data flowing in either direction. This device provides
an interface between cards operating at LVTTL logic
levels and a backplane operating at GTL/GTL+ signal
levels. Higher-speed operation is a direct result of the
reduced output swing (<1 V), reduced input threshold
levels, and OEC™ circuitry.
DGG PACKAGE
(TOP VIEW)
OEAB
1A1
GND
1A2
1A3
GND
VCC
1A4
GND
1A5
1A6
GND
1A7
1A8
GND
1A9
2A1
GND
2A2
2A3
GND
2A4
2A5
GND
2A6
VCC
GND
2A7
2A8
GND
2A9
OEBA
1
64
2
63
3
62
4
61
5
60
6
59
7
58
8
57
9
56
10
55
11
54
12
53
13
52
14
51
15
50
16
49
17
48
18
47
19
46
20
45
21
44
22
43
23
42
24
41
25
40
26
39
27
38
28
37
29
36
30
35
31
34
32
33
CLKAB
1CEAB
1CEBA
1B1
GND
1B2
1B3
VCC
1B4
1B5
1B6
GND
1B7
1B8
GND
1B9
2B1
GND
2B2
2B3
GND
2B4
2B5
2B6
VREF
2B7
2B8
GND
2B9
2CEBA
2CEAB
CLKBA
The user has the flexibility of using this device at either GTL (VTT = 1.2 V and VREF = 0.8 V) or the preferred
higher noise margin GTL+ (VTT = 1.5 V and VREF = 1 V) signal levels. GTL+ is the Texas Instruments derivative
of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3. The B port normally operates at GTL or
GTL+ signal levels, while the A-port and control inputs are compatible with LVTTL logic levels and are 5-V
tolerant. VREF is the reference input voltage for the B port.
Data flow in each direction is controlled by the output-enable (OEAB and OEBA) and clock (CLKAB and CLKBA)
inputs. The clock-enable (CEAB and CEBA) inputs control each 9-bit transceiver independently, which makes the
device more versatile.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus, OEC are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1996–2005, Texas Instruments Incorporated
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
For A-to-B data flow, the device operates on the low-to-high transition of CLKAB if CEAB is low. When OEAB is
low, the outputs are active. When OEAB is high, the outputs are in the high-impedance state. Data flow for B to
A is similar to that of A to B, but uses OEBA, CLKBA, and CEBA.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
Active bus-hold circuitry holds unused or undriven LVTTL inputs at a valid logic state. Use of pullup or pulldown
resistors with the bus-hold circuitry is not recommended.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
TSSOP – DGG
ORDERABLE PART NUMBER
Tape and reel
SN74GTL16622ADGGR
TOP-SIDE MARKING
GTL16622A
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
FUNCTION TABLE (1)
INPUTS
(1)
(2)
2
CEAB
OEAB
CLKAB
A
OUTPUT
B
MODE
Isolation
X
H
X
X
Z
H
L
X
X
B0 (2)
X
L
H or L
X
B0 (2)
L
L
↑
L
L
L
L
↑
H
H
Latched storage of A data
Clocked storage of A data
A-to-B data flow is shown. B-to-A data flow is similar, but uses OEBA, CLKBA, and CEBA.
Output level before the indicated steady-state input conditions are established
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
LOGIC DIAGRAM (POSITIVE LOGIC)
VREF
OEAB
1CEAB
CLKAB
CLKBA
1CEBA
OEBA
1A1
40
1
63
64
33
62
32
CE
1D
2
61
1B1
CLK
CE
1D
CLK
To Eight Other Channels
2CEAB
2CEBA
2A1
34
35
CE
1D
17
48
2B1
CLK
CE
1D
CLK
To Eight Other Channels
3
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
VCC
MIN
MAX
–0.5
4.6
A-port and control inputs
–0.5
6.5
B port and VREF
–0.5
4.6
A port
–0.5
6.5
B port
–0.5
4.6
Supply voltage range
VI
Input voltage range (2)
VO
Voltage range applied to any output in the high or power-off state (2)
IO
Current into any output in the low state
IO
Current into any A-port output in the high state (3)
A port
48
B port
100
Continuous current through each VCC or GND
UNIT
V
V
V
mA
48
mA
±100
mA
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
θJA
Package thermal impedance (4)
55
°C/W
Tstg
Storage temperature range
150
°C
(1)
(2)
(3)
(4)
–65
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
The current flows only when the output is in the high state and VO > VCC.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions (1) (2) (3) (4)
VCC
VTT
Termination voltage
VREF
Reference voltage
VI
Input voltage
VIH
High-level input voltage
VIL
Low-level input voltage
IIK
Input clamp current
IOH
High-level output current
IOL
Low-level output current
TA
Operating free-air temperature
(1)
(2)
(3)
(4)
4
MIN
NOM
MAX
UNIT
3.15
3.3
3.45
V
GTL
1.14
1.2
1.26
GTL+
1.35
1.5
1.65
GTL
0.74
0.8
0.87
GTL+
0.87
1
1.1
Supply voltage
B port
VTT
Except B port
5.5
B port
Except B port
VREF + 50 mV
VREF – 50 mV
Except B port
V
V
V
2
B port
V
0.8
V
–18
mA
A port
–24
mA
A port
24
B port
50
–40
85
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Normal connection sequence is GND first and VCC = 3.3 V, I/O, control inputs, VTT and VREF (any order) last.
VTT and RTT can be adjusted to accommodate backplane impedances if the dc recommended IOL ratings are not exceeded.
VREF can be adjusted to optimize noise margins, but normally is two-thirds VTT.
mA
°C
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
Electrical Characteristics
over recommended operating free-air temperature range for GTL/GTL+ (unless otherwise noted)
PARAMETER
VIK
VOH
A port
TEST CONDITIONS
VCC = 3.15 V,
II = –18 mA
VCC = 3.15 V to 3.45 V,
IOH = –100 µA
VCC – 0.2
IOH = –12 mA
2.4
IOH = –24 mA
2
VCC = 3.15 V
VCC = 3.15 V to 3.45 V,
A port
VOL
VCC = 3.15 V
VCC = 3.15 V to 3.45 V,
B port
II
VCC = 3.15 V
B port
VCC = 3.45 V,
A-port and control inputs
VCC = 3.45 V
Ioff
VCC = 0,
II(hold)
A port
MIN TYP (1)
VCC = 3.15 V
MAX
UNIT
–1.2
V
V
IOL = 100 µA
0.2
IOL = 12 mA
0.4
IOL = 24 mA
0.5
IOL = 100 µA
0.2
IOL = 10 mA
0.2
IOL = 40 mA
0.4
IOL = 50 mA
0.55
VI = VTT or GND
±5
VI = VCC or GND
±5
VI = 5.5 V or GND
±20
VI or VO = 0 to 5.5 V
100
VI = 0.8 V
VI = 2 V
V
µA
µA
75
µA
–75
VCC = 3.45 V (2),
VI = 0.8 V to 2 V
±500
IOZ (3)
A port
VCC = 3.45 V,
VO = VCC or GND
±10
µA
IOZH
B port
VCC = 3.45 V,
VO = 1.5 V
10
µA
Outputs high
60
Outputs low
60
Outputs disabled
60
ICC
A or B port
VCC = 3.45 V, A-port or control inputs at VCC or GND,
One input at VCC – 0.6 V
∆ICC (4)
Ci
Cio
(1)
(2)
(3)
(4)
VCC = 3.45 V,
IO = 0,
VI = VCC or GND
Control inputs
A port
B port
VI = 3.15 V or 0
VO = 3.15 V or 0
mA
500
µA
2.5
3
pF
6
8
6.5
8.5
pF
All typical values are at VCC = 3.3 V, TA = 25°C.
This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to
another.
For I/O ports, the parameter IOZ includes the input leakage current.
This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
5
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
Timing Requirements
over recommended ranges of supply voltage and operating free-air temperature for GTL (unless otherwise noted)
MIN
fclock
Clock frequency
tw
Pulse duration, CLK high or low
tsu
Setup time
th
Hold time
MAX
UNIT
200
MHz
2.5
Data before CLK↑
2.1
CE before CLK↑
3.3
Data after CLK↑
0.3
CE after CLK↑
ns
ns
ns
0
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature for GTL (see Figure 1)
PARAMETER
MIN
TYP (1) MAX
fmax
200
2.5
5.5
2.2
5.5
1.7
4.8
2.2
5.2
tdis
ten
CLKAB
B
OEAB
B
UNIT
MHz
ns
Both transitions (B port)
tr
Transition time, B outputs (0.6 V to 1 V)
0.6
2.2
ns
tf
Transition time, B outputs (1 V to 0.6 V)
0.4
1.5
ns
2.1
5.3
2.1
5
tPHL
ten
tdis
0.5
ns
Slew rate
tPLH
6
TO
(OUTPUT)
tPLH
tPHL
(1)
FROM
(INPUT)
CLKBA
A
OEBA
A
All typical values are at VCC = 3.3 V, TA = 25°C.
V/ns
1.7
5
2.3
5.5
ns
ns
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
Timing Requirements
over recommended ranges of supply voltage and operating free-air temperature for GTL+ (unless otherwise noted)
MIN
fclock
Clock frequency
tw
Pulse duration, CLK high or low
tsu
Setup time
th
Hold time
MAX
UNIT
200
MHz
2.5
Data before CLK↑
2.4
CE before CLK↑
3.2
Data after CLK↑
0.2
CE after CLK↑
ns
ns
ns
0
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature for GTL+ (see Figure 1)
TO
(OUTPUT)
UNIT
fmax
200
MHz
tPLH
2.6
4
5.6
2.3
4
5.7
2.4
3.8
5.2
1.8
3.4
5
tPHL
tPLH
tPHL
CLKAB
B
OEAB
B
ns
Both transitions (B port)
tr
Transition time, B outputs (0.6 V to 1.3 V)
1
1.6
2.7
ns
tf
Transition time, B outputs (1.3 V to 0.6 V)
0.5
1.1
3.2
ns
2
3.8
5.3
1.9
3.6
5
1.9
3.6
5
2.1
4
5.5
tPHL
ten
tdis
0.5
ns
Slew rate
tPLH
(1)
FROM
(INPUT)
MIN TYP (1) MAX
PARAMETER
CLKBA
A
OEBA
A
V/ns
ns
ns
All typical values are at VCC = 3.3 V, TA = 25°C.
7
SN74GTL16622A
18-BIT LVTTL-TO-GTL/GTL+ BUS TRANSCEIVER
www.ti.com
SCBS673F – AUGUST 1996 – REVISED APRIL 2005
PARAMETER MEASUREMENT INFORMATION
VTT
6V
500 Ω
From Output
Under Test
S1
Open
TEST
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
GND
CL = 50 pF
(see Note A)
500 Ω
25 Ω
S1
Open
6V
GND
From Output
Under Test
CL = 30 pF
(see Note A)
LOAD CIRCUIT FOR A OUTPUTS
Test
Point
LOAD CIRCUIT FOR B OUTPUTS
tw
3V
3V
1.5 V
1.5 V
Input
Timing
Input
1.5 V
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
Input
(see Note B)
3V
1.5 V
1.5 V
tsu
th
3V
Data Input
A Port
1.5 V
Data Input
B Port
VREF
1.5 V
0V
VTT
VREF
0V
0V
tPLH
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
tPHL
VOH
Output
VREF
VREF
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
(CLKAB to B port)
Input
(see Note B)
1.5 V
0V
tPLH
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
(CLKBA to A port)
tPLZ
3V
1.5 V
tPZH
1.5 V
1.5 V
0V
Output
Waveform 1
S1 at 6 V
(see Note C)
tPHL
VOH
Output
1.5 V
tPZL
3V
1.5 V
3V
Output
Control
(see Note B)
Output
Waveform 2
S1 at GND
(see Note C)
VOL + 0.3 V
VOL
tPHZ
VOH
1.5 V
VOH − 0.3 V
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
(OEBA to A port)
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
C. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
D. The outputs are measured one at a time, with one transition per measurement.
Figure 1. Load Circuits and Voltage Waveforms
8
PACKAGE OPTION ADDENDUM
www.ti.com
5-Sep-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
74GTL16622ADGGRE4
ACTIVE
TSSOP
DGG
64
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74GTL16622ADGGR
ACTIVE
TSSOP
DGG
64
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
0,50
48
0,08 M
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
1
0,25
24
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
48
56
64
A MAX
12,60
14,10
17,10
A MIN
12,40
13,90
16,90
DIM
4040078 / F 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated