PS-75 Series 75W Single Phase Industrial DIN Rail Power Supply F ea tures : U nivers a l A C i nput/F ull ra nge P rotections :Short circuit/O ver loa d/O ver v olta ge/O ver tempera ture C ooling by f ree a ir c onvection C a n be i ns ta lled on D IN r a il T S -35/7.5 o r 1 5 U L 5 08(indus tria l c ontrol e quipment)a pproved L E D i ndica tor for power o n 100% f ull loa d burn-in tes t F ix switching frequency a t 50K Hz 3 y ea rs w a rra nty R SPECIFICATION MODEL OUTPUT INPUT PS-7512 PS-7524 PS-7548 DC VOLTAGE 12V 24V 48V RATED CURRENT 6.3A 3.2A 1.6A CURRENT RANGE 0 ~ 6.3A 0 ~ 3.2A 0 ~ 1.6A RATED POWER 76W 76.8W 76.8W RIPPLE & NOISE (max.) Note.2 100mVp-p 150mVp-p 240mVp-p 12 ~ 14V 24 ~ 28V 48 ~ 53V VOLTAGE TOLERANCE Note.3 2.0% 1.0% 1.0% LINE R EGULATION 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 1.0% 1.0% VOLTAGE ADJ . R ANGE SETUP, R ISE, HOLD TIME 1000ms, 60ms, 50ms/230VAC VOLTAGE R ANGE 85 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz 76% AC CURRENT INRUSH CURRENT (max.) 1.6A / 115V AC 0.96A / 230V AC COLD START 20A / 115V AC 40A / 230V AC 81% <1mA / 240VAC OVER L OAD 105 ~ 150% rated output power Protection type : Constant current li miting, recovers automatically after fault condition is removed WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION HARMONIC CURRENT EMS IMMUNITY MTBF DIMENSION PACKING NOTE 80% LEAKAGE C URRENT OVER TEMPERATURE OTHERS 1 20 ~ 370VDC EFFICIENCY (Typ.) PROTECTION OVER VOLTAGE (Note 4) 1 800ms, 60ms, 10ms/115VAC at full load 15 ~ 16.5V 29 ~ 34V 58 ~ 65V Protection type : Hiccup mode, recovers automatically after fault condition is removed 85 5 (TSW1) Detect on heat sink of power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes UL508, EN60950 Approved I/P-O/P:3KVAC I /P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC Compliance to EN55011,EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,1 1, ENV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A 123.1K hrs min. MIL-HDBK-217F (25 ) 55.5*125.2*100mm (W*H*D) 0.6Kg; 20pcs/13Kg/1.1CUFT 1. A ll parameters N OT s pecially mentioned a re measured a t 230VAC i nput, r ated load a nd 25 of ambient temperature. 2. R ipple & n oise a re measured a t 20MHz o f bandwidth by using a 1 2" twisted pair-wire terminated with a 0 .1uf & 4 7uf parallel capacitor. 3. T olerance : i ncludes s et up tolerance, line regulation a nd load regulation. 4. T he power s upply is c onsidered a c omponent which will be installed into a f inal equipment. T he final equipment must be re-confirmed that it still meets E MC d irectives. 35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com PS-75 Series 75W Single Phase Industrial DIN Rail Power Supply 100 Mechanical Specification +V ADJ. 125.2 TB2 TB1 1 2 3 4 55.5 1 2 3 35 LE D ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15 Terminal Pin. No Assignment (TB1) Pin No. 1 2 3 Terminal Pin. No Assignment (TB2) Assignment FG AC/N AC/L Pin No. 1,2 3,4 Output Derating Assignment DC OUTPUT +V DC OUTPUT -V Output Derating Vs Input Voltage 100 100 24V,48V 90 80 12V 80 70 LOAD (%) LOAD (%) 60 40 20 60 50 40 -10 0 10 20 30 45 AMBIENT TEMPERATURE ( 50 ) 60 (VERTICAL) 85 90 105 125 145 165 185 205 225 245 265 INPUT VOLTAGE (V) 60Hz 35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com