UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 Digital Control Compatible Dual Low-Side ±4 Amp MOSFET Drivers with Programmable Common Current Sense Check for Samples: UCD7201 FEATURES DESCRIPTION • • • • • The UCD7201 is a member of the UCD7K family of digital control compatible drivers for applications utilizing digital control techniques or applications requiring fast local peak current limit protection. 1 2 • • • • • • Adjustable Current Limit Protection 3.3-V, 10-mA Internal Regulator DSP/μC Compatible Inputs Dual ±4-A TrueDrive™ High Current Drivers 10-ns Typical Rise and Fall Times with 2.2-nF Loads 20-ns Input-to-Output Propagation Delay 25-ns Current Sense-to-Output Propagation Delay Programmable Current Limit Threshold Digital Output Current Limit Flag 4.5-V to 15-V Supply Voltage Range Rated from -40°C to 105°C The UCD7201 includes dual low-side ±4-A high-current MOSFET gate drivers. It allows the digital power controllers such as UCD9110 or UCD9501 to interface to the power stage in double ended topologies. It provides a cycle-by-cycle current limit function for both driver channels, a programmable threshold and a digital output current limit flag which can be monitored by the host controller. With a fast cycle-by-cycle current limit protection, the driver can turn off the power stage in the event of an overcurrent condition. For fast switching speeds, the UCD7201 output stages use the TrueDrive™ output architecture, which delivers rated current of ±4 A into the gate of a MOSFET during the Miller plateau region of the switching transition. It also includes a 3.3-V, 10-mA linear regulator to provide power to the digital controller. APPLICATIONS • • • • Digitally Controlled Power Supplies DC/DC Converters Motor Controllers Line Drivers TYPICAL APPLICATION DIAGRAM (Push-Pull Converter) VIN Bias Winding VOUT Bias Supply DIGITAL CONTROLLER UCD7201PWP NC 14 1 NC ADC1 VCC 2 3V3 GND 4 AGND PWMA 3 PWMB VDD 13 PVDD 12 IN1 OUT1 11 5 IN2 OUT2 10 INTERRUPT or CCR 6 CLF PGND 9 PWM or GPIO 7 ILIM CS 8 ADC2 ADC3 ADC4 Isolation Amplifier COMMUNICATION (Programming & Status Reporting) 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TrueDrive, PowerPAD are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005–2009, Texas Instruments Incorporated UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION (CONT.) For similar applications requiring direct start-up capability from higher voltages such as the 48-V telecom input line, the UCD7601 includes a 110-V high-voltage startup circuit. The UCD7K driver family is compatible with standard 3.3-V I/O ports of DSPs, Microcontrollers, or ASICs. UCD7201 is offered in a PowerPAD™ HTSSOP-14 package. CONNECTION DIAGRAMS PWP−14 PACKAGE (TOP VIEW) NC 3V3 IN1 AGND IN2 CLF ILIM 1 2 3 4 5 6 7 14 13 12 11 10 9 8 NC VDD PVDD OUT1 OUT2 PGND CS NC − No internal connection ORDERING INFORMATION (1) TEMPERATURE RANGE CURRENT SENSE LIMIT PER CHANNEL 110-V HV STARTUP CIRCUIT PACKAGED DEVICES PowerPAD™ HTSSOP-14 (PWP) (1) -40°C to 105°C Common No UCD7201PWP HTSSOP-14 (PWP) package is available taped and reeled. Add R suffix to device type (e.g. UCD7201PWPR) to order quantities of 2,000 devices per reel for the PWP package. PACKAGING INFORMATION PACKAGE PowerPAD™ HTSSOP- 14 (1) 2 SUFFIX PWP θJC θJA (°C/W) (°C/W) 2.07 37.47 (1) POWER RATING TA = 70°C, DERATING FACTOR, ABOVE 70°C (mW/°C) TJ = 125°C (mW) 1470 27 PowerPAD™ soldered to the PWB (TI recommended PWB as defind in TI's application report SLMA002 pg.33) with OLFM. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 ABSOLUTE MAXIMUM RATINGS (1) SYMBOL VDD (2) PARAMETER UCD7201 UNIT 16 V Supply Voltage Quiescent 20 Switching, TA = 25°C, , TJ = 125°C, VDD = 12 V 200 IDD Supply Current VOUT Output Gate Drive Voltage OUT Output Gate Drive Current OUT IOUT(sink) IOUT(source) Analog Input mA -1 to PVDD 4.0 A -4.0 ISET, CS -0.3 to 3.6 ILIM -0.3 to 3.6 Digital I/O’s IN, CLF -0.3 to 3.6 Power Dissipation TA = 25°C (PWP-14 package), TJ = 125°C TJ Junction Operating Temperature UCD7201 Tstr Storage Temperature HBM CDM (1) (2) ESD Rating V V 2.67 W -55 to 150 °C -65 to 150 Human body model 2000 Change device model 500 V Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND. Currents are positive into, negative out of the specified terminal. ELECTRICAL CHARACTERISTICS VDD = 12 V, 4.7-μF capacitor from VDD to GND, 0.22μF from 3V3 to AGND, TA = TJ = -40°C to 105°C, (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY SECTION Supply current, OFF VDD = 4.2 V - 200 400 μA Supply current Outputs not switching IN = LOW - 1.5 2.5 mA VDD UVLO ON 4.25 4.5 4.75 VDD UVLO OFF 4.05 4.25 4.45 VDD UVLO hysteresis 150 250 350 3.267 3.3 3.333 3.234 3.3 3.366 LOW VOLTAGE UNDER-VOLTAGE LOCKOUT V mV REFERENCE / EXTERNAL BIAS SUPPLY 3V3 initial set point TA = 25°C, ILOAD = 0 3V3 set point over temperature 3V3 load regulation ILOAD = 1 mA to 10 mA, VDD = 5 V - 1 6.6 3V3 line regulation VDD = 4.75 V to 12 V, ILOAD = 10 mA - 1 6.6 Short circuit current VDD = 4.75 to 12 V 11 20 35 3V3 OK threshold, ON 3.3 V rising 2.9 3.0 3.1 3V3 OK threshold, OFF 3.3 V falling 2.7 2.8 2.9 HIGH, positive-going input threshold voltage (VIT+) 1.65 - 2.08 LOW negative-going input threshold voltage (VIT-) 1.16 - 1.5 0.6 - 0.8 - - 2 V mV mA V INPUT SIGNAL Input voltage hysteresis, (VIT+ VIT-) Frequency Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 V MHz 3 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com ELECTRICAL CHARACTERISTICS (continued) VDD = 12 V, 4.7-μF capacitor from VDD to GND, 0.22μF from 3V3 to AGND, TA = TJ = -40°C to 105°C, (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX 0.51 0.55 0.58 1.05 1.10 1.15 UNIT CURRENT LIMIT (ILIM) ILIM internal current limit threshold ILIM = OPEN ILIM maximum current limit threshold ILIM = 3.3 V ILIM current limit threshold ILIM = 0.75 V 0.700 0.725 0.750 ILIM minimum current limit threshold ILIM = 0.25 V 0.21 0.23 0.25 CLF output high level CS > ILIM , ILOAD = -7 mA 2.64 - - CLF output low level CS ≤ ILIM, ILOAD = 7 mA - - 0.66 Propagation delay from IN to CLF IN rising to CLF falling after a current limit event - 10 20 ns Includes CS comp offset 5 25 50 mV - –1 - μA V CURRENT SENSE COMPARATOR Bias voltage Input bias current Propagation delay from CS to OUTx ILIM = 0.5 V, measured on OUTx, CS = threshold + 60 mV - 25 40 Propagation delay from CS to CLF ILIM = 0.5 V, measured on CLF, CS = threshold + 60 mV - 25 50 10 35 75 ns CURRENT SENSE DISCHARGE TRANSISTOR Discharge resistance IN = low, resistance from CS to AGND Ω OUTPUT DRIVERS Source current VDD = 12 V, IN = high, OUTx = 5 V 4 Sink current VDD = 12 V, IN = low, OUTx = 5 V 4 Source current VDD = 4.75 V, IN = high, OUTx = 0 2 Sink current VDD = 4.75 V, IN = low, OUTx = 4.75 V Rise time, tR CLOAD= 2.2 nF, VDD = 12 V 10 20 Fall time, tF CLOAD = 2.2 nF, VDD = 12 V 10 15 Output with VDD < UVLO VDD =1.0 V, ISINK = 10 mA 0.8 1.2 Propagation delay from IN to OUT1, tD1 CLOAD = 2.2 nF, VDD = 12 V, CLK rising 20 35 Propagation delay from IN to OUT2, tD2 CLOAD = 2.2 nF, VDD = 12 V, CLK falling 20 35 4 A 3 ns V ns Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 FUNCTIONAL BLOCK DIAGRAM NC 1 3V3 2 IN1 3 AGND 4 IN2 5 CLF 6 3V3 Regulator UVLO NC 13 VDD 12 PVDD 11 OUT1 10 OUT2 9 PGND 8 CS + and Reference 14 + Q SD 25 mV R Q ILIM R 7 Figure 1. UCD7201 Timing Diagram VIT+ INPUT VIT− tF tF tD1 90% tD2 OUTPUT 10% Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 5 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com TERMINAL FUNCTIONS UCD7201 PIN NAME I/O - NC - No Connection 2 1 3V3 O Regulated 3.3-V rail. The onboard linear voltage regulator is capable of sourcing up to 10 mA of current. Place 0.22 μF of ceramic capacitance from this pin to ground. 3 2 IN1 I The IN pin is a high impedance digital input capable of accepting 3.3-V logic level signals up to 2 MHz. There is an internal Schmitt trigger comparator which isolates the internal circuitry from any external noise. 4 3 AGND - Analog ground return. 5 4 IN2 I The IN pin is a high impedance digital input capable of accepting 3.3-V logic level signals up to 2 MHz. There is an internal Schmitt trigger comparator which isolates the internal circuitry from any external noise. 6 5 CLF O Current limit flag. When the CS level is greater than the ILIM voltage minus 25 mV, the output of the driver is forced low and the current limit flag (CLF) is set high. The CLF signal is latched high until the device receives the next rising edge on the IN pin. 7 6 ILIM I Current limit threshold set pin. The current limit threshold can be set to any value between 0.25 V and 1.0 V. The default value while open is 0.5 V. 8 7 CS I Current sense pin. Fast current limit comparator connected to the CS pin is used to protect the power stage by implementing cycle-by-cycle current limiting. 9 8, 9 PGND - Power ground return. The pin should be connected very closely to the source of the power MOSFET. 10 10 OUT2 O The high-current TrueDrive™ driver output. 11 11 OUT1 O The high-current TrueDrive™ driver output. 12 12 PVDD I Supply pin provides power for the output drivers. It is not connected internally to the VDD supply rail. The bypass capacitor for this pin should be returned to PGND. 13 13 VDD I Supply input pin to power the driver. The UCD7K devices accept an input range of 4.5 V to 15 V. Bypass the pin with at least 4.7 μF of capacitance, returned to AGND. 14 14, 15, 16 NC - HTSSOP -14 PIN # QFN-16 PIN # 1 6 FUNCTION No Connection. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 APPLICATION INFORMATION The UCD7201 is member of the UCD7K family of digital compatible drivers targeting applications utilizing digital control techniques or applications that require local fast peak current limit protection. Supply The UCD7K devices accept a supply range of 4.5 V to 15 V. The device has an internal precision linear regulator that produces the 3V3 output from this VDD input. A separate pin, PVDD, not connected internally to the VDD supply rail provides power for the output drivers. In all applications the same bus voltage supplies the two pins. It is recommended that a low value of resistance be placed between the two pins so that the local capacitance on each pin forms low pass filters to attenuate any switching noise that may be on the bus. Although quiescent VDD current is low, total supply current depends on the gate drive output current required for capacitive load and switching frequency. Total VDD current is the sum of quiescent VDD current and the average OUT current. Knowing the operating frequency and the MOSFET gate charge (QG), average OUT current can be calculated from: IOUT = QG x f, where f is frequency. For the best high-speed circuit performance, VDD bypass capacitors are recommended to prevent noise problems. A 4.7-μF ceramic capacitor should be located closest to the VDD and the AGND connection. In addition, a larger capacitor with relatively low ESR should be connected to the PVDD and PGND pin, to help deliver the high current peaks to the load. The capacitors should present a low impedance characteristic for the expected current levels in the driver application. The use of surface mount components for all bypass capacitors is highly recommended. Reference / External Bias Supply All devices in the UCD7K family are capable of supplying a regulated 3.3-V rail to power various types of external loads such as a microcontroller or an ASIC. The onboard linear voltage regulator is capable of sourcing up to 10 mA of current. For normal operation, place 0.22-μF of ceramic capacitance between the 3V3 pin to the AGND pin. Input Pin The input pins are high impedance digital inputs capable of accepting 3.3-V logic level signals up to 2 MHz. There is an internal Schmitt Trigger comparator which isolates the internal circuitry from any external noise. If limiting the rise or fall times to the power device is desired then an external resistance may be added between the output of the driver and the load device, which is generally the gate of a power MOSFET. Current Sensing and Protection A very fast current limit comparator connected to the CS pin is used to protect the power stage by implementing cycle-by-cycle current limiting. The current limit threshold may be set to any value between 0.25 V and 1.0 V by applying the desired threshold voltage to the current limit (ILIM) pin. If the ILIM pin is left floating, the internal current limit threshold will be 0.5 volts. When the CS level is greater than the ILIM voltage minus 25 mV, the output of the driver is forced low and the current limit flag (CLF) is set high. The CLF signal is latched high until the device receives the next rising edge on either of the IN pins. When the CS voltage is below ILIM, the driver output follows the PWM input. The CLF digital output flag can be monitored by the host controller to determine when a current limit event occurs and to then apply the appropriate algorithm to obtain the desired current limit profile (i.e. straight time, fold back, hickup or latch-off). A benefit of this local protection feature is that the UCD7K devices can protect the power stage if the software code in the digital controller becomes corrupted. If the controller’s PWM output stays high, the local current sense circuit turns off the driver output when an over-current event occurs. The system would then likely go into retry mode because most DSP and microcontrollers have on-board watchdog, brown-out, and other supervisory peripherals to restart the device in the event that it is not operating properly. But these peripherals typically do not react fast enough to save the power stage. The UCD7K’s local current limit comparator provides the required fast protection for the power stage. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 7 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com The CS threshold is 25 mV below the ILIM voltage. If the user attempts to command zero current while the CS pin is at ground the CLF flag will latch high until the IN pin receives a pulse. At start-up it is necessary to ensure that the ILIM pin will always be greater than the CS pin for the handshaking to work as described below. If for any reason the CS pin comes to within 25 mV of the ILIM pin during start-up, then the CLF flag will be latched high and the digital controller must poll the UCD7K device, by sending it a narrow IN pulse. If a fault condition is not present the IN pulse will reset the CLF signal to low indicating that the UCD7K device is ready to process power pulses. Handshaking The UCD7K family of devices have a built-in handshaking feature to facilitate efficient start-up of the digitally controlled power supply. At start-up the CLF flag is held high until all the internal and external supply voltages of the UCD7K device are within their operating range. Once the supply voltages are within acceptable limits, the CLF goes low and the device will process input drive signals. The micro-controller should monitor the CFL flag at start-up and wait for the CLF flag to go LOW before sending power pulses to the UCD7K device. Driver Output The high-current output stage of the UCD7K device family is capable of supplying ±4-A peak current pulses and swings to both PVDD and PGND. The driver outputs follow the state of the IN pin provided that the VDD and 3V3 voltages are above their respective under-voltage lockout threshold. The drive output utilizes Texas Instruments' TrueDrive™ architecture, which delivers rated current into the gate of a MOSFET when it is most needed, during the Miller plateau region of the switching transition providing efficiency gains. TrueDrive™ consists of pullup pulldown circuits with bipolar and MOSFET transistors in parallel. The peak output current rating is the combined current from the bipolar and MOSFET transistors. This hybrid output stage also allows efficient current sourcing at low supply voltages. Each output stage also provides a very low impedance to overshoot and undershoot due to the body diode of the external MOSFET. This means that in many cases, external-schottky-clamp diodes are not required. Source/Sink Capabilities During Miller Plateau Large power MOSFETs present a large load to the control circuitry. Proper drive is required for efficient, reliable operation. The UCD7K drivers have been optimized to provide maximum drive to a power MOSFET during the Miller plateau region of the switching transition. This interval occurs while the drain voltage is swinging between the voltage levels dictated by the power topology, requiring the charging/discharging of the drain-gate capacitance with current supplied or removed by the driver device. See Reference [1] Drive Current and Power Requirements The UCD7K family of drivers can deliver high current into a MOSFET gate for a period of several hundred nanoseconds. High peak current is required to turn the device ON quickly. Then, to turn the device OFF, the driver is required to sink a similar amount of current to ground. This repeats at the operating frequency of the power device. Reference [1] discusses the current required to drive a power MOSFET and other capacitive-input switching devices. When a driver device is tested with a discrete, capacitive load it is a fairly simple matter to calculate the power that is required from the bias supply. The energy that must be transferred from the bias supply to charge the capacitor is given by: E + 1 CV2 2 (1) where C is the load capacitor and V is the bias voltage feeding the driver. There is an equal amount of energy transferred to ground when the capacitor is discharged. This leads to a power loss given by the following: P + CV 2 f (2) where f is the switching frequency. 8 Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 This power is dissipated in the resistive elements of the circuit. Thus, with no external resistor between the driver and gate, this power is dissipated inside the driver. Half of the total power is dissipated when the capacitor is charged, and the other half is dissipated when the capacitor is discharged. With VDD = 12 V, CLOAD = 2.2 nF, and f = 300 kHz, the power loss can be calculated as: P + 2.2 nF 122 300 kHz + 0.095 W (3) With a 12-V supply, this would equate to a current of: I + P + 0.095 W + 7.9 mA V 12 V (4) Operational Waveforms Figure 24 shows the circuit performance achievable with the output driving a 10-nF load at 12-V VDD. The input pulsewidth (not shown) is set to 200 ns to show both transitions in the output waveform. Note the linear rising and falling edges of the switching waveforms. This is due to the constant output current characteristic of TrueDrive™ stage as opposed to the resistive output impedance of traditional MOSFET-based gate drivers. Thermal Information The useful range of a driver is greatly affected by the drive power requirements of the load and the thermal characteristics of the device package. In order for a power driver to be useful over a particular temperature range the package must allow for the efficient removal of the heat produced while keeping the junction temperature within rated limits. The UCD7K family of drivers is available in PowerPAD™ TSSOP and QFN/DFN packages to cover a range of application requirements. Both have an exposed pad to enhance thermal conductivity from the semiconductor junction. As illustrated in Reference [2], the PowerPAD™ packages offer a leadframe die pad that is exposed at the base of the package. This pad is soldered to the copper on the PC board (PCB) directly underneath the device package, reducing the TJC down to 2.07°C/W. The PC board must be designed with thermal lands and thermal vias to complete the heat removal subsystem, as summarized in Reference [3]. Note that the PowerPAD™ is not directly connected to any leads of the package. However, it is electrically and thermally connected to the substrate which is the ground of the device. The PowerPad™ should be connected to the quiet ground of the circuit. Circuit Layout Recommendations In a power driver operating at high frequency, it is critical to minimize stray inductance to minimize overshoot/undershoots and ringing. The low output impedance of these drivers produces waveforms with high di/dt. This tends to induce ringing in the parasitic inductances. It is advantageous to connect the driver device close to the MOSFETs. It is recommended that the PGND and the AGND pins be connected to the PowerPad™ of the package with a thin trace. It is critical to ensure that the voltage potential between these two pins does not exceed 0.3 V. The use of schottky diodes on the outputs to PGND and PVDD is recommended when driving gate transformers. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 9 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com Additional Application Circuits Figure 2 shows the UCD7201 in a half-bridge converter design. The digital controller is performing the output voltage compensation and all supervisory functions. The isolation amplifier is made up of a linear opto-coupler configured for a gain of 1/10, so the output voltage is transformed to a level comparable with the ADC of the digital controller. VOUT VIN Bias Winding CS XFMR Bias Supply DIGITAL CONTROLLER ADC1 UCD7201PWP NC 14 1 NC VCC 2 3V3 PVDD 12 GND 4 AGND VDD 13 PWMA 3 IN1 OUT1 11 PWMB 5 IN2 OUT2 10 6 CLF PGND 9 7 ILIM CS 8 ADC2 INTERRUPT or CCR PWM or GPIO Gate Drive Transformer (3 winding) ADC3 ADC4 Isolation Amplifier COMMUNICATION (Programming & Status Reporting) Figure 2. Half-Bridge Converter Figure 3 shows the UCD7201 in an analog only implementation of an intermediate bus converter. The ILIM pin of the UCD7201 is exponentially increased at start-up, which minimizes overshoot on the output voltage. The UCC28089 is a push-pull controller with fixed dead-time. The UCC28089 operates at a fixed duty cycle close to 100% so the circuit acts like a DC transformer linearly transforming the input voltage via the turns ratio of the transformer. VIN Bias Supply Bias Winding VOUT UCC28089 VDD 16 1 SYNC 1 NC UCD7201 NC 14 2 3V3 2 DIS GND 13 3 CT 4 CS 4 AGND PVDD 12 VDD 13 OUTA 15 3 IN1 OUT1 11 OUTB 14 5 IN2 OUT2 10 6 CLF PGND 9 7 ILIM CS 8 Figure 3. Intermediate Bus Converter 10 Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 Typical Characteristics UVLO THRESHOLDS vs TEMPERATURE 3V3 REFERENCE VOLTAGE vs TEMPERATURE 5.0 3.36 UVLO on 4.5 3.34 UVLO off 3V3 − Reference Voltage − V VUVLO − UVLO Thresholds − V 4.0 3.5 3.0 2.5 2.0 1.5 3.32 3.30 3.28 1.0 3.26 0.5 0.0 −50 UVLO hysteresis 3.24 −25 0 25 50 75 100 125 −50 t − Temperature − °C 0 25 50 75 t − Temperature − °C Figure 4. Figure 5. 3V3 SHORT CIRCUIT CURRENT vs TEMPERATURE SUPPLY CURRENT vs FREQUENCY (VDD = 5 V) 23.0 100 125 160 140 22.5 IDD − Supply Current − mA ISHORT_CKT − Short Circuit Current − mA −25 22.0 VDD = 4.75 V 21.5 VDD = 12 V 21.0 CLOAD = 10 nF 120 100 80 CLOAD = 4.7 nF 60 40 CLOAD = 2.2 nF 20.5 20 20.0 −50 CLOAD = 1 nF 0 −25 0 25 50 75 t − Temperature − °C 100 125 0 500 1000 1500 f − Frequency − kHz Figure 6. Figure 7. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 11 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com SUPPLY CURRENT vs FREQUENCY (VDD = 10 V) 280 320 240 280 CLOAD = 10 nF IDD − Supply Current − mA IDD − Supply Current − mA SUPPLY CURRENT vs FREQUENCY (VDD = 8 V) 200 160 CLOAD = 4.7 nF 120 80 240 CLOAD = 10 nF 200 160 CLOAD = 4.7 nF 120 80 CLOAD = 2.2 nF 40 CLOAD = 2.2 nF 40 CLOAD = 1 nF 0 0 500 0 1500 1000 CLOAD = 1 nF 0 500 Figure 8. Figure 9. SUPPLY CURRENT vs FREQUENCY (VDD = 12 V) SUPPLY CURRENT vs FREQUENCY (VDD = 15 V) 500 400 450 350 300 IDD − Supply Current − mA 400 IDD − Supply Current − mA 1500 f − Frequency − kHz f − Frequency − kHz CLOAD = 10 nF 250 200 CLOAD = 4.7 nF 150 100 CLOAD = 2.2 nF CLOAD = 10 nF 350 300 CLOAD = 4.7 nF 250 200 150 CLOAD = 2.2 nF 100 50 50 CLOAD = 1 nF CLOAD = 1 nF 0 0 500 1000 0 1500 0 500 1000 1500 f − Frequency − kHz f − Frequency − kHz Figure 10. 12 1000 Figure 11. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 INPUT THRESHOLDS vs TEMPERATURE OUTPUT RISE TIME AND FALL TIME vs TEMPERATURE (VDD = 12 V) 2.5 18.0 CLOAD = 2.2 nF 16.0 tR, tF − Rise and Fall Times − ns Input Rising VINPUT − Input Voltage − V 2.0 1.5 Input Falling 1.0 tR = Rise Time 14.0 12.0 10.0 tF = Fall Time 8.0 6.0 4.0 0.5 2.0 0.0 0.0 −50 −25 0 25 50 75 100 −50 125 −25 0 25 50 75 100 125 TJ − Temperature − °C TJ − Temperature − °C Figure 12. Figure 13. RISE TIME vs SUPPLY VOLTAGE FALL TIME vs SUPPLY VOLTAGE 65 45 40 55 35 45 tF − Fall Time − ns tR − Rise Time − ns CLOAD = 10 nF CLOAD = 4.7 nF 35 25 CLOAD = 10 nF 30 25 CLOAD = 4.7 nF 20 CLOAD = 2.2 nF CLOAD = 2.2 nF 15 15 CLOAD = 1 nF 10 CLOAD = 1 nF 5 5 5 7.5 10 12.5 15 5 VDD − Supply Voltage − V 7.5 10 12.5 15 VDD − Supply Voltage − V Figure 14. Figure 15. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 13 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com IN to OUTx PROPAGATION DELAY RISING vs SUPPLY VOLTAGE IN to OUTx PROPAGATION DELAY FALLING vs SUPPLY VOLTAGE 25 tPD − Propagation Delay, Falling − ns tPD − Propagation Delay, Rising − ns 20 CLOAD = 10 nF 15 10 CLOAD = 4.7 nF 5 CLOAD = 2.2 nF CLOAD = 10 nF 20 15 CLOAD = 4.7 nF 10 CLOAD = 2.2 nF CLOAD = 1 nF CLOAD = 1 nF 5 0 5 7.5 10 12.5 15 5 7.5 Figure 16. Figure 17. DEFAULT CURRENT LIMIT THRESHOLD vs TEMPERATURE CS TO OUTx PROPAGATION DELAY vs TEMPERATURE 0.59 40 0.58 35 tPD − CS to OUTx Propagation Delay − ns VCS − Current Limit Threshold − V 12.5 15 VDD − Supply Voltage − V VDD − Supply Voltage − V 0.57 0.56 0.55 0.54 0.53 0.52 30 25 20 15 10 5 0 0.51 −50 −25 0 25 50 75 100 125 −50 TJ − Temperature − °C −25 0 25 50 75 100 125 TJ − Temperature − °C Figure 18. 14 10 Figure 19. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 CS TO CLF PROPAGATION DELAY vs TEMPERATURE IN TO OUT PROPAGATION DELAY vs TEMPERATURE 35 50 30 40 tPD − Propagation Delay − ns tPD − CS to CLF Propagation Delay − ns 45 35 30 25 20 15 10 25 20 15 10 5 5 0 0 −50 −25 0 25 50 75 100 125 −50 −25 0 25 50 75 100 125 TJ − Temperature − °C TJ − Temperature − °C Figure 20. Figure 21. START-UP BEHAVIOR AT VDD = 12 V (INPUT TIED TO 3V3) SHUT DOWN BEHAVIOR AT VDD = 12 V (INPUT TIED TO 3V3) VDD (2 V/div) VDD (2 V/div) 3V3 (2 V/div) OUTx (2 V/div) 3V3 (2 V/div) OUTx (2 V/div) t − Time − 40 µs/div t − Time − 40 µs/div Figure 22. Figure 23. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 15 UCD7201 SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 www.ti.com START-UP BEHAVIOR AT VDD = 12 V (INPUT SHORTED TO GND) SHUT DOWN BEHAVIOR AT VDD = 12 V (INPUT SHORTED TO GND) VDD (2 V/div) VDD (2 V/div) 3V3 (2 V/div) 3V3 (2 V/div) OUTx (2 V/div) OUTx (2 V/div) t − Time − 40 µs/div t − Time − 40 µs/div Figure 24. Figure 25. Output Voltage − 2 V/div OUTPUT RISE AND FALL TIME (VDD = 12 V, CLOAD = 10 nF) t − Time − 40 ns/div Figure 26. 16 Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 UCD7201 www.ti.com SLUS645E – FEBRUARY 2005 – REVISED NOVEMBER 2009 REFERENCES 1. Power Supply Seminar SEM-1400 Topic 2: Design And Application Guide For High Speed MOSFET Gate Drive Circuits, by Laszlo Balogh, Texas Instruments Literature No. SLUP133. 2. Technical Brief, PowerPad Thermally Enhanced Package, Texas Instruments Literature No. SLMA002 3. Application Brief, PowerPAD Made Easy, Texas Instruments Literature No. SLMA004 RELATED PRODUCTS TEMPERATURE RANGE UCD7100 FEATURES 3V3, CS (1) Single Low Side ±4-A Driver with Independent CS Dual Low Side ±4-A Drivers with Independent CS 3V3, CS UCD7230 ±4-A Synchronous Buck Driver with CS 3V3, CS (1) UCD7500 Single Low Side ±4-A Driver with CS and 110-V High Voltage Startup UCD7601 3v3, CS, HVS110 Dual Low Side ±4-A Drivers with Independent CS and 110-V High Voltage Startup Dual Low Side ±4-A Drivers with Common CS and 110-V High Voltage Startup UCD9110 Digital Power Controller for High Performance Single-loop Applications UCD9501 Digital Power Controller for High Performance Multi-Loop Applications (2) (1) (2) UCD7200 UCD7600 (1) (2) (3) (4) CURRENT SENSE LIMIT PER CHANNEL (2) (1) (2) (3) 3V3, CS, HVS110 (1) (2) (3) 3V3, CCS, HVS110 (1) (4) (3) 3V3 = 3.3-V linear regulator. CS = current sense and current limit function. HVS110 = 110-V high voltage startup circuit. CCS = Common current sense and current limit function. REVISION HISTORY DATE REVISION CHANGE DESCRIPTION 3/4/05 SLUS645 Initial release of preliminary datasheet. 4/1/05 SLUS645A Updated packaging information. 7/14/05 SLUS645B Initial release of production datasheet. Updated specification and application information. Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated Product Folder Link(s): UCD7201 17 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) UCD7201PWP ACTIVE HTSSOP PWP 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 105 UCD7201 UCD7201PWPG4 ACTIVE HTSSOP PWP 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 105 UCD7201 UCD7201PWPR ACTIVE HTSSOP PWP 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 105 UCD7201 UCD7201PWPRG4 ACTIVE HTSSOP PWP 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR -40 to 105 UCD7201 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device UCD7201PWPR Package Package Pins Type Drawing SPQ HTSSOP 2000 PWP 14 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 12.4 Pack Materials-Page 1 6.9 B0 (mm) K0 (mm) P1 (mm) 5.6 1.6 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCD7201PWPR HTSSOP PWP 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated