Cree® XLamp® MX-6 LEDs Data Sheet The Cree XLamp MX-6 LED provides the proven lighting-class performance and reliability of Cree XLamp LEDs in a flat-top PLCC package. The XLamp MX-6 LED continues Cree’s history of innovation in LEDs for lighting applications with wide viewing angle, unlimited floor life, uniform light output without secondary optics and electrically neutral thermal path. The XLamp MX-6 LED brings high performance and quality of light to a wide range of lighting applications, including linear lighting, LED light bulbs, fluorescent retrofits and retail-display lighting. FEATURES • Available in white (2,600 K to 8,300 K CCT) • Maximum drive current: 1000 mA • Wide viewing angle: 120° • Electrically neutral thermal path • Qualification at max drive current • RoHS-compliant • Unlimited floor life at ≤ 30°C/85% RH ev 2 CLD-DS23 R Data Sheet: Table of Contents Flux Characteristics (TJ = 25°C).................................................................................................................. 2 Characteristics......................................................................................................................................... 2 Relative Spectral Power Distribution............................................................................................................ 3 Relative Flux vs. Junction Temperature (IF = 300 mA).................................................................................... 3 Electrical Characteristics (TJ = 25°C)........................................................................................................... 4 Relative Flux vs. Current (TJ = 25°C).......................................................................................................... 4 Thermal Design........................................................................................................................................ 5 Typical Spatial Distribution......................................................................................................................... 5 Reflow Soldering Characteristics................................................................................................................. 6 Notes...................................................................................................................................................... 7 Mechanical Dimensions (TA = 25°C)............................................................................................................ 8 Tape and Reel.......................................................................................................................................... 9 Packaging.............................................................................................................................................. 10 Subject to change without notice. www.cree.com/xlamp 1 Flux Characteristics (TJ = 25°C) The following table provides several base order codes for XLamp MX-6 LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp MX-6 LED Binning and Labeling document. CCT Range Color Cool White Warm White Min. Max. 5,000 K 8,300 K 3,700 K 4,300 K 2,600 K 3,700 K Calculated Min Luminous Flux (lm) @ 350 mA* Base Order Codes Min Luminous Flux (lm) @ 300 mA Order Code Group Flux (lm) Flux (lm) Q4 100 114 MX6AWT-A1-0000-000C51 Q5 107 122 MX6AWT-A1-0000-000D51 Q3 93.9 107 MX6AWT-A1-0000-000BE5 P4 80.6 92 MX6AWT-A1-0000-0009E7 * Calculated values for reference purposes only. Notes: • Cree maintains a tolerance of +/- 7% on flux measurements. • Typical CRI for Cool White (4,300 K – 8,300 K CCT) is 75. • Typical CRI for Warm White (2,600 K – 4,300 K CCT) is 80. Characteristics Characteristics Thermal resistance, junction to solder point Viewing angle (FWHM) Temperature coefficient of voltage Unit Typical °C/W 5 degrees 120 mV/°C -3.3 ESD classification (HBM per Mil-Std-883D) DC forward current Minimum Maximum Class 2 mA Forward voltage (@ 300 mA) V LED junction temperature °C 1000 3.3 3.8 150 * The increase of maximum forward current to 1000 mA for XLamp MX-6 White is retroactive and applies to all XLamp MX-6 White LEDs produced by Cree. This increase is the result of more extensive testing that was performed after the initial product launch. Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 2 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Relative Spectral Power Distribution Relative Spectral Power Relative Radiant Power (%) 100 80 60 5000K - 8300K CCT 3500K - 5000K CCT 40 2600K - 3500K CCT 20 0 400 450 500 550 600 650 700 750 Wavelength (nm) Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 300 mA) 100% Relative Luminous Flux 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 3 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Electrical Characteristics (TJ = 25°C) 1000 900 Forward Current (mA) 800 700 600 500 400 300 200 100 0 2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 Forward Voltage (V) Relative Flux vs. Current (TJ = 25°C) Relative Luminous Flux (%) 300 250 200 150 100 50 0 100 200 300 400 500 600 700 800 900 1000 Forward Current (mA) Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 4 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1200 Maximum Current (mA) 1000 800 600 Rj-a = = 10°C/W 10°C/W Rj-a Rj-a Rj-a = = 20°C/W 20°C/W Rj-a Rj-a = = 30°C/W 30°C/W Rj-a Rj-a = = 40°C/W 40°C/W 400 200 0 0 25 50 75 100 125 150 Ambient Temperature (ºC) Typical Spatial Distribution Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (º) Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 5 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Reflow Soldering Characteristics In testing, Cree has found XLamp MX-6 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Based Solder Lead-Free Solder 3°C/second max. 3°C/second max. Preheat: Temperature Min (Tsmin) 100°C 150°C Preheat: Temperature Max (Tsmax) 150°C 200°C 60-120 seconds 60-180 seconds 183°C 217°C 60-150 seconds 60-150 seconds 215°C 260°C 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5°C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25°C to Peak Temperature Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 6 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Notes Lumen Maintenance Projections Based on internal long-term reliability testing, Cree currently projects cool white and neutral white (chromaticity bins 0A – 6D4) XLamp MX-6 LEDs to maintain an average of 70% or higher lumen maintenance after 10,000 hours, provided the LED is operated with a constant current of up to 500 mA and ambient air temperature around the LED is maintained at or below 85°C. Based on internal long-term reliability testing, Cree currently projects warm white (chromaticity bins 7A1 – 8D4) XLamp MX-6 LEDs to maintain an average of 70% or higher lumen maintenance after 25,000 hours, provided the LED is operated with a constant current of up to 500 mA and ambient air temperature around the LED is maintained at or below 85°C. Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature and drive current affect the LED junction temperature. ENERGY STAR Recommendation Cree currently recommends a maximum drive current of 350 mA for XLamp MX-6 white in designs seeking the ENERGY STAR* 35,000 hour lifetime rating (≥ 94.1% luminous flux @ 6000 hours) or 25,000 hour lifetime rating (≥ 91.8% luminous flux @ 6000 hours). * These lifetime ratings are based on the current ENERGY STAR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STAR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, Cree has found XLamp MX-6 LEDs to have unlimited floor life in conditions ≤30ºC / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85ºC / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2002/95/ EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 7 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Mechanical Dimensions (TA = 25°C) All measurements are ±.13 mm unless otherwise indicated. Top View Top View Bottom View Side View Recommended FR4 Solder Pad Recommended MCPCB Solder Pad Alternative Solder Pad Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 8 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp 1.5±.1 4.0±.1 8.0±.1 1.75±.10 2.5±.1 Cathode Side Tape and Reel +.3 12.0 .0 All dimensions in mm. Anode Side User Feed Direction (denoted by + and circle) END START User Feed Direction END START Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) Loaded Pockets (1,000 Lamps) Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) User Feed Direction Cover Tape Pocket Tape 13mm 7" Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 9 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp Dessicant Desiccant (inside bag) (inside bag) Packaging Humidity Indicator Humidity Indicator Card (inside bag)bag) (inside All dimensions in mm. Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label Bin with Cree Bin CREE Code & Barcode Label Code, Qty, Lot # Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Label with Customer P/N, Qty, Lot #, PO## Code, Qty, Lot Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Patent Label Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO# Label with Cree Bin Code, Qty, Lot # Copyright © 2009-2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. 10 CLD-DS23 Rev 2 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp