AC-DC 120-240 Watts xppower.com DNR120-240TS Series • Rugged Design for Industrial Applications • Up to 88% Typical Efficiency • Wide Adjustment Range • Full Power to 60 ºC • Three Phase Operation • Single Phase Operation • -25 ºC to 70 ºC Operation Specification Input General Input Voltage • 340-575 VAC 3Ø (1Ø to 1Ø operation with 75% output derating), 480-820 VDC Input Frequency • 47-63 Hz Input Current • DNR120TS: 0.35 A at 500 VAC DNR240TS: 0.70 A at 500 VAC Inrush Current • 120 W 15 A typical at 500 VAC, cold start 240 W 20 A typical at 500 VAC, cold start Power Factor • 0.6 at 500 VAC input and nominal load Earth Leakage Current • 0.32 mA Efficiency Isolation Switching Frequency Signals MTBF Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Line Regulation Load Regulation Transient Response • • • • • • • • • • Ripple & Noise Overvoltage Protection Overload Protection Temperature Coefficient Current Share • • • • See table See table ±1% No minimum load required <1000 ms <150 ms 20 ms min at 400 VAC ±1% ±1% (±5% for units in parallel) 4% max deviation recovering to within 1% in 1 ms for 50% load change 100 mV pk-pk 20 MHz BW 120-145%, recycle input to reset Continuous current limit ±0.02%/°C • 2 units can be connected in parallel, DNR240TS only, total output derates by 10% • See table • 3000 VAC Input to Output 1500 VAC Input to Ground 500 VAC Output to Ground • DNR120TS: 65 kHz typical DNR240TS: 25 kHz typical • DC ON indicator LED Green, DC LOW indicator LED Red DC OK: normally open relay on 24 V models • 210 kHrs to MIL-STD 217 F Environmental Operating Temperature • -25 ºC to 70 ºC, derate linearly from 60 ºC at 3.5%/ºC (see derating curve) Cooling • Convection-cooled Operating Humidity • 20-95% RH, non-condensing Storage Temperature • -25 °C to +85 °C Shock • 4 g peak, 22 ms on X, Y and Z axis Vibration • 10 to 500 Hz, 1 g rms on X, Y and Z axis EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Magnetic Field Dips & Interruptions Safety Approvals • • • • • • • • • • EN55022, class B conducted & radiated EN61000-3-2, class A EN61000-3-3 EN61000-4-2, level 4 perf criteria A EN61000-4-3, level 3 perf criteria A EN61000-4-4, level 4 perf criteria A EN61000-4-5, level 3 perf criteria B EN61000-4-6, level 3 perf criteria A EN61000-4-8, level 4 perf criteria A EN61000-4-11, 30% 500 ms, 60% 200 ms, 100% 5000 ms Perf Criteria A, A, A • EN60950-1:2001, UL508, UL60950-1 Output Voltage 12 V 24 V 24 V 48 V AC-DC DNR120-240TS Models and Ratings Output Voltage Trim 11.4-14.5 V 22.5-28.5 V 22.5-28.5 V 47.0-56.0 V Output Current(1) 10.0 A 5.0 A 10.0 A 5.0 A Typical Efficiency 87% 88% 87% 88% Model Number DNR120TS12 DNR120TS24 DNR240TS24-I DNR240TS48-I Notes 1. Reduce by 25% for single phase input operation. Mechanical Details 0.3 (7.0) 4.39 (111.3) 6 1 DC LO ON DNR120TS DNR240TS 4.87 (123.6) 4.87 (123.6) DC LO ON Single Parallel 1 4 1 4 AC Input AC Input 2.93 (74.3) 4 1 5 6 DC Output 3.50 (89.0) DC OK signal connector on underside Notes 1. All dimensions in inches (mm). 2. Weight - DNR120TS: 1.76 lb (800 g) approx. DNR240TS: 2.43 lb (1100 g) approx. 3. Screw terminal: 10-24 AWG cable size. DC OK signal connector: 10-24 AWG cable 4. DC OK Relay 60 VDC at 300 mA 5. Allow 0.98” (25 mm) clearance all round for cooling Pin Connections - AC Input Pin Designation 1 Ground 2 L1 3 L2 4 L3 Pin 1 2 3 4 5 6 Pin Connections - DC Output Designation -V -V +V +V DC OK* DC OK* * Available on 24 V versions. Derating Curves DNR120-240TS Load (%) 100 75 0 -25 60 70 Ambient Temp (˚C) 18-Nov-08