ASTEC LPS170-M

175 Watts
LPS170-M Series
Total Power: 110-175 Watts
Input Voltage: 85-264 VAC
120-300 VDC
# of Outputs: Single
MEDICAL
Electrical Specs
Input
Input range
Frequency
Inrush current
Efficiency
EMI filter
85-264 VAC, 120-300 VDC
47-63 Hz
38 A max, cold start @ 25°C
75% typical at full load
Meets FCC Class A conducted
CISPR 22 Class A conducted
EN55022 Class A conducted
VDE 0878 PT3 Class A conducted
0.99 typical
Power factor
Safety ground
leakage current
Output
Special Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
<250 µA @ 50/60 Hz, 264 VAC inputS
Maximum power
Medical safety approvals
Active power factor correction
IEC EN61000-3-2 compliance
Wide Range Adjustable output
Remote sense on main output
Single wire current sharing
Power fail and remote inhibit
Built-in EMI filter
Low output ripple
Overvoltage protection
Overload protection
Thermal overload protection
DC power good
5 V standby output
12 V Aux output
Optional cover (-C suffix)
Adjustment range
Hold-up time
Overload protection
Overvoltage protection
Standby output
Aux output
110 W convection (75 W with cover)
175 W with 30 CFM forced air
(130 W with cover)
2:1 wide ratio minimum
20 ms @175 W load at nominal line
Short circuit protection on all outputs.
Case overload protected @ 110-145%
above peak rating
10% to 40% above nominal output
5 V @ 2A regulated ±5%
12 V @ 1 A -5 %, +10%
Logic Control
Power failure
Remote inhibit
Environmental
Remote sense
Operating temperature: 0° to 50°C ambientderate
each output at 2.5% per degree from 50° to 70°C
Electromagnetic susceptibility: designed to meet
IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3
DC Ok
Humidity: Operating; non-condensing
TTL logic signal goes high 100 - 500
msec after V1 output; It goes low at
least 4 msec before loss of regulation
Requires contact closure to inhibit
outputs
Compensates for 0.5 V lead drop min.
Will operate without remote sense
connected. Reverse connection
protected.
TTL logic signal goes high after main
output is in regulation. It goes low
when there is a loss of regulation
5% to 95%
Vibration: Three orthogonal axes, sweep at
Safety
1 oct/min, 5 min. dwell at four major resonances
0.75 G peak 5 Hz to 500 Hz, operational
Storage temperature: -40° to 85°C
Temperature coefficient: ± .04% per °C
MTBF demonstrated: >550,000 hours at full load
and 25°C ambient conditions
100
America’s (USA): 1-888-41-ASTEC
VDE
UL
CSA
CE
Europe (UK): 44 (1384) 842-211
0750/EN60601-1 (IEC601)
UL2601
CSA 22.2 No. 601.1
Mark (LVD)
Asia (HK): 852-2437-9662
rev 06.23.04
AMERICAS
EUROPE
ASIA
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Model
Number
Output
Voltage
Minimum
Load
Maximum Load with
Convection Cooling
Maximum Load with
30 CFM Forced Air
Peak
Load
Regulation2
Ripple
P/P(PARD)3
LPS172-M
LPS173-M
LPS174-M
LPS175-M
5 V (2.5-6V)
12 V (6-12 V)
15 V (12-24 V)
24 V (24-54 V)
0A
0A
0A
0A
22 A
9.1 A
7.3 A
4.5 A
35 A
15 A
12 A
7.5 A
38 A
16.5 A
13.2 A
8.2 A
±2%
±2%
±2%
±2%
50 mV
120 mV
<1%
<1%
LPS170-M Series
Ordering Information
1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4. Remote inhibit resets OVP latch
Note: -C suffix added to the model number indicates cover option.
Ordering Information
5
6
LPS17x
SK1
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
PIN 7
PIN 8
PIN 9
PIN 10
+12V
5V Standby
Common
V1 SWP
Common
+V1 sense
Sense common
Remote inhibit
DC power good
POK
SK3
TB-1
TB-2
COMMON
Main output
SK4
PIN 1
PIN 3
PIN 5
GROUND
LINE
NEUTRAL
+
-
10
SK1
Connector
Mating Connectors
(SK4) AC Input:
1
SK3
1.50
(38.1)
Voltage Adj
POT
5 3 1
(SK3) DC Output:
0.55
(14.0)
7.4
(188.0)
8.5
(216.0)
M3
#6-32
Molex 19141-0058
SK4
0.88
(22.2)
1.07
(27.2)
Molex 90142-0010 (USA)
PINS: 90119-2110 or
Amp: 87977-3
PINS: 87309-8
0.95
(24.0)
6.61
(168.0)
Molex 09-50-8051 (USA)
Molex 09-91-0500 (UK)
PINS: 08-58-0111
(SK1) Control Signals:
0.75
(19.0)
2.50
(63.5)
www.astecpower.com
2.11
(53.5)
Notes:
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ±0.02”.
3. Specifications are for convection rating at factory settings unless
otherwise stated.
4. Mounting screw maximum insertion depth is 0.12”.
5. Warranty: 1 year
6. Weight: 1.8 lb / 0.85 kg
4.25
(108.0)
Astec connector kit #70-841-016
#6-32(8 PLACES)
M3(8 PLACES)
101