Agilent HSDL-9000 Miniature Surface-Mount Ambient Light Photo Sensor Data Sheet Description The HSDL-9000 is a low cost, digital-output ambient light photo sensor in miniature industrystandard PLCC lead-free surfacemount package. It incorporates a photodiode, which peaks in human luminosity curve at 550 nm. Hence, it provides an excellent responsivity that is close to the response of human eyes, as shown in Figure 2. With the options of three digital levels and an analog Gain Control pin to fine tune the three threshold levels to achieve better sensitivity control, the HSDL9000 is ideal for applications in which the measurement of ambient light is used to control display backlighting. Mobile appliances such as mobile phones and PDAs that draw heavy current from the display backlighting will benefit from incorporating the HSDL-9000 in their designs to reduce the power consumption significantly. Features • Excellent responsivity which peaks in the human luminosity curve at 550 nm Close responsivity to the human eye • Miniature PLCC surface-mount package Height – 1.1 mm Width – 4.0 mm Depth – 3.2 mm • Ease of design with digital output Integrated photodiode and analog to digital output circuitry • Enable fine control of the backlight intensity with adjustable sensitivity control 3 digital levels An Analog Gain Control • Minimum power consumption 30 µA typical idle (standby) current <10 nA typical shutdown current • Guaranteed temperature performance –25°C to 85°C • 2.7 ≤ VCC ≤ 3.6 V • Lead-free package • Low cost Applications • Detection of ambient light to control display backlighting Mobile devices – mobile phones, PDAs Automotive – dashboard Consumer appliances – audio sets • Daylight and artificial light exposed devices Ordering Information Part Number Packaging Type Package Quantity HSDL-9000 Tape and Reel 6-lead PLCC with Top Transparent Epoxy Surface 1500 Application Circuit For HSDL-9000 Ambient Light Photo Sensor VCC C1 R1 (1) (5) AGain VCC DOUT ANALOG TO DIGITAL CIRCUITRY (6) HSDL-9000 GND (4) A0 A1 (2) (3) Figure 1. Functional block diagram of HSDL-9000. I/O Pins Configuration Table Pin Symbol I/O Description Notes 1 VCC I Supply Voltage Regulated, 2.7 to 3.6 Volt 2 A0 I Digital Gain Level Control_0 This pin needs to be driven high or low and not left floating. 3 A1 I Digital Gain Level Control_1 This pin needs to be driven high or low and not left floating. 4 GND I Ground Connect to System Ground 5 AGain I Analog Gain Constant Control If not used, leave this pin unconnected. 6 DOUT O Digital Output Tri-State[1] Note: 1. The HSDL-9000 is in tri-state when it is in shut down mode. I/O Truth Table[2] Logic Level A1 A0 Description Incidence Light Threshold (Lux)[3] 0 0 High Gain 30 1 0 Medium Gain 81 0 1 Low Gain 164 1 1 Shut down – Notes: 2. AGain pin is left floating. 3. Measurements are carried out using incandescent light source. 2 Recommended Application Circuit Components Component Recommended Value C1 1.0 µF ± 20%, Tantalum Recommended R1 Values[4] Incidence Light Threshold (Lux) R1 High Gain Medium Gain Low Gain 220 kΩ ± 5%, 0.25 W 23 50 81 430 kΩ ± 5%, 0.25 W 25 63 108 910 kΩ ± 5%, 0.25 W 28 71 133 Note: 4. Measurements are carried out using incandescent light source. NORMALIZED RESPONSIVITY 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 HSDL-9000 SILICON EYE 0.2 0.1 0 350 450 550 650 750 850 950 1050 WAVELENGTH – nm Figure 2. Relative spectral responsivity vs. wavelength. Caution: The BiCMOS inherent to this design of this component increases the component’s susceptibility to damage from Electrostatic Discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation, which may be induced by the ESD. 3 Absolute Maximum Ratings For implementations where case to ambient thermal resistance is ≤ 50°C/W Parameter Symbol Min. Max. Units Storage Temperature TS –25 +85 °C Operating Temperature TA –25 +85 °C Supply Voltage VCC 0 6 V Output Voltage: RxD VO –0.5 6 V Conditions Recommended Operating Conditions Parameter Symbol Min. Max. Units Operating Temperature TA –25 +85 °C Supply Voltage VCC 2.7 3.6 V Logic Input Logic High VIH VCC – 0.2 VCC V Logic Low VIL 0 0.2 V Conditions Electrical & Optical Specifications Specifications (Min. & Max. values) hold over the recommended operating conditions unless otherwise noted. Unspecified test conditions may be anywhere in their operating range. All typical values (Typ.) are at 25°C with V CC at 3.0 V unless otherwise noted. Parameter Symbol Peak Sensitivity Wavelength λP Min. Viewing Angle Logic Input Typ. Max. Units 550 nm 120 ° Conditions Logic High VIH VCC –0.2 VCC V Logic Low VIL 0 0.2 V Output Voltage Logic High VOH VCC –0.2 VCC V IOH = –200 µA Logic Low VOL 0 0.2 V IOL = 200 µA Supply Current ICC 33 100 µA Shutdown Current ICC (SD) 10 100 nA 4 HSDL-9000 Package Outline 1.1 ± 0.2 4 ± 0.2 1.27 ± 0.1 1.27 ± 0.1 6 5 0.15 MAX. 0.55 ± 0.1 4 3.2 ± 0.2 1 2 3.5 ± 0.2 3 0.8 ± 0.3 0.15 MAX. 0.4 SEATING PLANE 0.1 C C 0.4 ± 0.1 Figure 3. Package outline dimensions. 5 PIN 1. 2. 3. 4. 5. 6. SYMBOL VCC A0 A1 GND AGain DOUT Tape and Reel Dimensions 4.0 ± 0.1 UNIT: mm 1.75 ± 0.1 ∅ 1.5 +0 1 2.0 ± 0.05 POLARITY 5.5 ± 0.05 PIN 1: VCC PIN 4: GND 12.0 +0.3–0.1 4.22 ± 0.1 ∅ 1.5 +0.25 3.61 ± 0.1 0.304 ± 0.02 8.0 ± 0.1 1.25 ± 0.1 PROGRESSIVE DIRECTION EMPTY PARTS MOUNTED LEADER (400 mm MIN.) (40 mm MIN.) EMPTY (40 mm MIN.) UNIT: mm DETAIL A 180 ± 0.5 2.0 ± 0.5 +0 62.5 –2.5 ∅ 13.0 ± 0.2 R 1.0 LABEL 24 ± 0.5 DETAIL A 18.4 MAX. 12.4 +2 –0 Figure 4. Tape and reel dimensions. 6 Moisture Proof Packaging All HSDL-9000 options are shipped in moisture proof package. Once opened, moisture absorption begins. Baking Conditions If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the parts. This part is compliant to JEDEC Level 2a. Package Temp. Time In reels 60°C 20 hours In bulk 125°C 5 hours Baking should only be done once. UNITS IN A SEALED MOISTURE-PROOF PACKAGE Recommended Storage Conditions Storage Temperature 10°C to 30°C Relative Humidity below 60% RH PACKAGE IS OPENED (UNSEALED) Time from Unsealing to Soldering After removal from the bag, the parts should be soldered within twenty-eight days if stored at the recommended storage conditions. If times longer than 28 days are needed, the parts must be stored in a dry box. ENVIRONMENT LESS THAN 30°C, AND LESS THAN 60% RH YES NO BAKING IS NECESSARY YES PACKAGE IS OPENED LESS THAN 672 HOURS (4 WEEKS) NO PERFORM RECOMMENDED BAKING CONDITIONS Figure 5. Baking conditions chart. 7 NO Reflow Profile MAX. 260°C T – TEMPERATURE – (°C) 255 R3 230 220 200 180 R2 60 sec. MAX. ABOVE 220°C 160 R1 120 R4 R5 80 25 0 50 100 150 200 250 300 t-TIME (SECONDS) P1 HEAT UP P2 SOLDER PASTE DRY P3 SOLDER REFLOW P4 COOL DOWN Figure 6. Reflow graph. Process Symbol ∆T Maximum ∆T/∆time Heat Up P1, R1 25°C to 160°C 4°C/s Solder Paste Dry P2, R2 160°C to 200°C 0.5°C/s Solder Reflow P3, R3 200°C to 255°C (260°C at 10 seconds max.) 4°C/s P3, R4 255°C to 200°C –6°C/s P4, R5 200°C to 25°C –6°C/s Cool Down The reflow profile is a straightline representation of a nominal temperature profile for a convective reflow solder process. The temperature profile is divided into four process zones, each with different ∆T/∆time temperature change rates. The ∆T/∆time rates detailed in the above table. The temperatures are measured at the component to printed circuit board connections. In process zone P1, the PC board and I/O pins are heated to a temperature of 160°C to activate the flux in the solder paste. The temperature ramp up rate, R1, is limited to 4°C per second to allow for even heating of both the PC board and ALPS I/O pins. 8 Process zone P2 should be of sufficient time duration (60 to –120 seconds) to dry the solder paste. The temperature is raised to a level just below the liquidus point of the solder, usually 200°C (392°F). Process zone P3 is the solder reflow zone. In zone P3, the temperature is quickly raised above the liquidus point of solder to 255°C (491°F) for optimum results. The dwell time above the liquidus point of solder should be between 20 and 60 seconds. It usually takes about 20 seconds to assure proper coalescence of the solder balls into liquid solder and the formation of good solder connections. Beyond a dwell time of 60 seconds, the intermetallic growth within the solder connections becomes excessive, resulting in the formation of weak and unreliable connections. The temperature is then rapidly reduced to a point below the solidus temperature of the solder, usually 200°C (392°F), to allow the solder within the connections to freeze solid. Process zone P4 is the cool down after solder freeze. The cool down rate, R5, from the liquidus point of the solder to 25°C (77°F) should not exceed –6°C per second maximum. This limitation is necessary to allow the PC board and transceiver’s castellation I/O pins to change dimensions evenly, putting minimal stresses on the ALPS. Appendix A : SMT Assembly Application Note 1.0 Solder Pad, Mask and Metal Stencil Aperture METAL STENCIL FOR SOLDER PASTE PRINTING STENCIL APERTURE LAND PATTERN SOLDER MASK PCBA Figure 7. Stencil and PCBA. 1.1 Recommended Land Pattern 4.7 1.5 0.6 1.27 3.14 CL MOUNTING CENTER UNITS: mm Figure 8. Stencil and PCBA. 9 CL 1.2 Recommended Metal Solder Stencil Aperture It is recommended that only a 0.152 mm (0.006 inches) thick stencil be used for solder paste printing. This is to ensure adequate printed solder paste volume and no shorting. APERTURES AS PER LAND DIMENSION 0.152 Aperture opening for shield pad is 1.5 mm x 0.6 mm as per land pattern. 4.7 3.14 Figure 9. Solder stencil aperture. 1.3 Adjacent Land Keepout and Solder Mask Areas Adjacent land keep-out is the maximum space occupied by the unit relative to the land pattern. There should be no other SMD components within this area. 5.1 0.2 MIN. C L The minimum solder resist strip width required to avoid solder bridging adjacent pads is 0.2 mm. Note: Wet/Liquid PhotoImageable solder resist/mask is recommended. 4.8 SOLDER MASK UNITS: mm C L Figure 10. Adjacent land keepout and solder mask areas. 10 Appendix B: PCB Layout Suggestion The following PCB layout shows a recommended layout that should result in good electrical and EMI performance. Things to note: 1. The ground plane should be continuous under the part, but should not extend under the shield trace. 2. The shield trace is a wide, low inductance trace back to the system ground. Top Layer Figure 11. PCB layout suggestions. 11 3. C1 and C2 are optional V CC filter capacitors. They may be left out if the V CC is clean. A reference layout of a 2-layer Agilent evaluation board for HSDL-9000 based on the guidelines stated above is shown below. For more details, please refer to Agilent Application Note 1114, Infrared Transceiver PC Board Layout for Noise Immunity. Bottom Layer Appendix C: Optical Window Design for HSDL-9000 Optical Window Dimensions To ensure that the performance of the HSDL-9000 will not be affected by improper window design, there are some constraints on the dimensions and design of the window. There is a constraint on the minimum size of the window, which is placed in front of the photodiode, so that it will not affect the angular response of the HSDL-9000. This minimum dimension that is recommended will ensure at least a ± 35° light reception cone. If a smaller window is required, a light pipe or light guide can be used. A light pipe or light guide Figure 12. Recommended window design. 12 is a cylindrical piece of transparent plastic which makes use of total internal reflection to focus the light. The thickness of the window should be kept as minimum as possible because there is a loss of power in every optical window of about 8% due to reflection (4% on each side) and an additional loss of energy in the plastic material. Figure 12 illustrates the two types of window that we have recommended which could either be a flat window or a flat window with light pipe. The table and figure below show the recommended dimensions of the window. These dimension values are based on a window thickness of 1.0 mm with a refractive index 1.585. Figure 13. Recommended window dimensions. WD: D1: T: L: D2: Z: Working Distance between window front panel & HSDL-9000 Window Diameter Thickness Length of Light Pipe Light Pipe Diameter Distance between window rear panel and HSDL-9000 Table 4. Recommended Dimension for Optical Window WD (T+L+Z) 1.5 2.0 2.5 3.0 Flat Window (L = 0.0) Z D1 0.5 2.25 1.0 3.25 1.5 4.25 5.00 5.00 Flat Window with Light Pipe (D2 = 1.5; z = 0.5) D1 L – – – – – – 2.5 1.5 All Dimensions are in mm. The window should be placed directly on top of the photodiode to achieve better performance and if a flat window with a light pipe is used, dimension D2 should be 1.5 mm (same size as 13 the PIN) to optimize the performance of HSDL-9000. Please refer to Figure 14 for the top view of the placement of the window. Optical Window Material The material of the window is recommended to be polycarbonate. The surface finish of the plastic should be smooth, without any texture. The recommended plastic material for use as a window is available from Bayer AG and Bayer Antwerp N. V. (Europe), Bayer Corp.(USA) and Bayer Polymers Co., Ltd. (Thailand). Table 5. Recommended Plastic Material Material Number Makrolon LQ2647 Makrolon LQ3147 Makrolon LQ3187 Figure 14. Placement of the window. www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152 (Domestic/International), or 0120-61-1280 (Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright © 2003 Agilent Technologies, Inc. May 5, 2003 5988-9204EN Visible Light Transmission 87% 87% 85% Refractive Index 1.587 1.587 1.587