Features Description GM3255 products are 280 kHz switching regulators with a high efficiency, 1.5 A integrated switch. These parts operate over a wide input voltage range, from 2.7 V to 30 V. The flexibility of the design allows the chips to operate in most power supply configurations, including boost, flyback, forward, inverting, and SEPIC. The ICs utilize current mode architecture, which allows excellent load and line regulation, as well as a practical means for limiting current. Combining high frequency operation with a highly integrated regulator circuit results in an extremely compact power supply solution. The circuit design includes provisions for features such as frequency synchronization, shutdown, and feedback controls for either positive or negative voltage regulation. Integrated Power Switch: 1.5 A Guaranteed Input Voltage Range: 2.7 V to 30 V High Frequency Allows for Small Components Minimum External Components Easy External Synchronization Built in Overcurrent Protection Frequency Foldback Reduces Component Stress During an Overcurrent Condition Thermal Shutdown with Hysteresis Regulates Either Positive or Negative Output Voltages Shut Down Current: 50 µA Maximum Wide Temperature Range Commercial Commercial Grade : 0 to 70°C (GM3255) Application Boost Regulators Multiple Output Flyback Supplies CCFL Backlight Driver Inverting Supplies Laptop Computer Supplies TFT LCD Bias Supplies TYPICAL APPLICATION CIRCUITS C1 0.01µF GM3255 1 VC VSW 8 2 FB PGND 7 3 Test AGND 4 SS SS D1 VOUT 5V MBRS120T3 6 L1 VCC 5 22µH + C3 22µF 3.3V R1 5k R3 1.28k +C2 22µF www.gammamicro.com GM3255 V0.11 R2 3.72K 1 MARKING INFORMATION & PIN CONFIGURATIONS (TOP VIEW) SOP-8 & NSOP-8 PGND VSW AGND VCC 8 7 6 5 GM3255 AYWW 1 2 A = Assembly Location Y = Year W W = Work Week 3 4 VC FB SS Test Ordering Number Package Shipping GM3255S8T GM3255S8R GM3255NS8T GM3255NS8R SOP - 8 SOP - 8 NSOP - 8 NSOP - 8 100 Units / Tube 2,500 Units / Tape & Reel 100 Units / Tube 2,500 Units / Tape & Reel * For detail Ordering Number identification, please see last page. PIN DESCRIPTION PIN NUMBER FUNCTION PIN SYMBOL 1 VC Loop compensation pin. The VC pin is the output of the error amplifier and is used for loop compensation, current limit and start. Loop compensation can be implemented by a simple RC network as shown in the application diagram on page 2 as R1 and C1. 2 FB Positive regulator feedback pin. This pin senses a positive output voltage and is referenced to 1.276V. When the voltage at this pin falls below 0.4 V, chip switching frequency reduces to 20% of the nominal frequency. 3 Test These pins are connected to internal test logic and should either be left floating or tied to ground. Connection to a voltage between 9.5V and 15V shuts down the internal oscillator and leaves the power switch running. 4 SS Synchronization and shutdown pin. This pin may be used to synchronize the part to nearly twice the base frequency. A TTL low shut the part down and put it into low current mode. If synchronization is not used, this pin should be either tied high or left floating for normal operation. 5 VCC Input power supply pin. This pin supplies power to the part and should have a bypass capacitor connected to AGND. 6 AGND Analog ground. This pin provides a clean ground for the controller circuitry ans should not be in the path of large currents. The output voltage sensing resistors should be connected to the IC substrate. 7 PGND Power ground. This pin is the ground connection for the emitter of the power switching transistor. Connection to a good ground plane is essential. 8 VSW High current switch pin. This pin connects internally to the collector of the power switch. The open voltage across the power switch can be as high as 40V. To minimize radiation, use a trace as short as practical. GM3255 ABSOLUTE MAXIMUM RATINGS 2 PARAMETER VALUE UNITS Package Thermal Resistance Junction-to-Case, RqJC junction-to-Ambient, RqJC 45 165 °C / W °C / W Junction Temperature Range, TJ -40 to +150 °C Storage Temperature Range, TSTG -65 to +150 °C Lead Temperature (Peak) (reflow - soldering 60 sec. maximum above 183°C) 230 °C ESD, Human Body Model 1.2 kV * The maximum package power dissipation must be observed. MAXIMUM RATINGS: PIN SYMBOL VMAX VMIN ISOURCE ISINK IC Power Input VCC 30 V -0.3 V N/A 200 mA Shutdown / Sync SS 30 V -0.3 V 1 mA 1 mA Loop Compensation VC 6V -0.3 V 10 mA 10 mA Voltage Feedback Input FB 10 V -0.3 V 1 mA 1 mA Test 6V -0.3 V 1 mA 1.0 mA Power Ground PGND 0.3 V -0.3 V 4A 10 mA Analog Ground AGND 0V 0V N/A 10 mA VSW 40 V -0.3 V 10 mA 3A PIN NAME Test Pin Switch Input BLOCK DIAGRAM VCC Shutdown Thermal Shutdown 2.0V Regulator Oscillator Delay Timer Sync SS S PWM Latch Q R Frequency Shift 5 :1 VSW Switch Driver X5 Slope Compensation 63mW 4µA Test + - PWM Comparator Ramp Summer PGND 0.4 V Detector + FB 1.276 V Positive Error Amp AGND GM3255 VC 3 Power Management ELECTRICAL CHARACTERISTICS (2.7 V < VCC < 30 V; Industrial Grade: 0°C < TJ < 70°C; Commercial Grade: 0°C < TJ< 125°C; unless otherwise noted) CHARACTERISTICS UNIT TEST CONDITIONS MIN TYP MAX VC tied to FB; measure at FB 1.246 1.276 1.300 V FB Input Current FB = VREF -1.0 0.1 1.0 µA FB Reference Voltage Line Regulation VC = FB - 0.01 0.03 %/V IVC = ±25 µA 300 550 800 µMho Error Amp Gain (Note 2) 200 500 - V/V Negative Error Amp Gain Error Amplifier Section FB Reference Voltage Error Amp Transconductance (Note 2) 100 180 320 V/V VC Source Current FB = 1.0V, VC =1.25V 25 50 90 µA VC Sink Current FB = 1.5V, VC = 1.25V 200 625 1500 µA FB = 1.0V; VC sources 25µA 1.5 1.7 1.9 V VC High Clamp Voltage FB = 1.5V, VC sinks 25µA 0.25 0.50 0.65 V Reduce VC from 1.5V until switching stops 0.75 1.05 1.30 V Base Operating Frequency FB = 1.0V 230 280 310 kHz Reduced Operating Frequency FB = 0V 30 52 120 kHz VC Low Clamp Voltage VC Threshold Oscillator Section Maximum Duty Cycle FB Frequency Shift Threshold - 90 94 - % Frequency drops to reduced operating frequency 0.36 0.40 0.44 V - 320 - 500 kHz Rise time = 20ns 2.5 - - V SS = 0V SS = 3.0V -15 - -3.0 3.0 8.0 µA 0.5 0.85 1.2 µs 12 12 80 36 350 200 µs Sync/ Shutdown Section Sync Range Sync Pulse Transition Threshold SS Bias Current Shutdown Threshold Shutdown Delay 2.7 V VCC 12 V < VCC 12V 30V GM3255 (Note 1) The maximum package power dissipation must be observed. (Note 2) Guaranteed by design, not 100% tested in production. 4 ELECTRICAL CHARACTERISTICS (2.7 V < VCC < 30 V; Industrial Grade: 0°C < TJ < 70°C; Commercial Grade: 0°C < TJ < 125°C; unless otherwise noted) CHARACTERISTICS UNIT TEST CONDITIONS MIN ISWITCH = 1.5A, (Note 2) - 0.8 1.4 - 0.55 1.00 ISWITCH=1.0A, -40°C TA 0°C(Note 2) - 0.75 1.30 ISWITCH = 10mA - 0.09 0.45 50% duty cycle(Note 2) 80% duty cycle(Note 2) 1.6 1.5 1.9 1.7 2.4 2.2 A FB = 0 V, ISW =4.0A(Note 2 ) 200 250 300 ns - 10 30 TYP MAX Power Switch Section Switch Saturation Voltage ISWITCH = 1.0A, 0°C TJ Switch Current Limit Minimum Pulse Width D ICC / DVSW Switch Leakage 85°C 1.0A V 2.7 V VCC 12V, 10mA ISW 12V VCC 30V, 10mA ISW 1.0A - - 100 2.7 V VCC 12V, 10mA ISW 1.5A (Note 2) - 17 30 12V VCC 30V, 10mA ISW 1.5A (Note 2) - - 100 VSW = 40 V, VCC = 0V - 2.0 100 µA ISW = 0 - 5.5 8.0 mA mA / A General Section Operating Current VC < 0.8V, SS = 0V, 2.7V VCC 12V - 12 60 VC < 0.8V, SS = 0V, 12V VCC 30V - - 100 VSW switching, maximum ISW = 10mA - 2.45 2.70 V Thermal Shutdown (Note2) 150 180 210 °C Thermal Hysteresis (Note2) - 25 - °C Shutdown Mode Current Minimum Operation Input Voltage µA GM3255 (Note 2) Guaranteed by design, not 100% tested in production. 5 TYPICAL PERFORMANCE CHARACTERISTICS 7.2 1.9 7.0 VCC = 30 V 6.8 1.8 VCC = 12V 6.4 VIN (V) Current (mA) 6.6 1.7 6.2 6.0 1.6 VCC = 2.7V 5.8 5.6 0 50 1.5 100 0 50 100 Temperature (°C) Temperature (°C) Figure 1. ICC (No Switching) vs. Temperature Figure 2. Minimum Input Voltage vs. Temperature 285 2.60 280 2.50 Current (A) fosc (kHz) 275 270 VCC = 12V VCC = 2.7V 2.40 265 2.30 260 VCC = 30 V 255 0 50 100 Temperature (°C) 99 VCC = 30V Duty Cycle (%) VCC = 12V 97 96 VCC = 22.7V 95 94 93 0 50 100 Temperature (°C) GM3255 Figure 5. Maximum Duty Cycle vs. Temperature 6 0 50 100 Temperature (°C) Figure 3. Switching Frequency vs. Temperature (GM3255 only) 98 2.20 Figure 4. Current Limit vs. Temperature APPLICATION INFORMATION Shown in Figure 6. The power switch is turned off by the output of the PWM Comparator. Current Mode Control VCC Oscillator S VC + L Q R Power Switch In Out CO X5 SUMMER Slope Compensation D1 VSW PWM Comparator RLOAD Driver 63 m A TTL-compatible sync input at the SS pin is capable of syncing up to 1.8 times the base oscillator frequency. As shown in Figure 7, in order to sync to a higher frequency, a positive transition turns on the power switch before the output of the oscillator goes high, thereby resetting the oscillator. The sync operation allows multiple power supplies to operate at the same frequency. Figure 6. Current Mode Control Scheme A sustained logic low at the SS pin will shut down the IC and reduce the supply current. GM3255 family incorporates a current mode control scheme. In which the PWM ramp signal is derived from the power switch current. This ramp signal is compared to the output of the error amplifier to control the on-time power switch. The oscillator is used as a fixedfrequency clock to ensure a constant operational frequency. The resulting control scheme features several advantages over conventional voltage mode control. First, derived directly from the inductor, the ramp signal responds immediately to line voltage changes. This An additional feature includes frequency shift to 20% of the nominal frequency when either the NFB or FB pins trigger the threshold. During power up, overload, or short circuit conditions, the minimum switch on-time is limited by the PWM comparator minimum pulse width. Extra switch off-time reduces the minimum duty cycle to protect external components and the IC itself. As Previously mentioned, this block also produces a ramp for the slope compensation to improve regulator stability. eliminates the delay caused by the output filter and erError Amplifier ror amplifier, which is commonly found in voltage mode controllers. The second benefit comes from inherent VC pulse-by pulse current limiting by merely clamping the peak switching current. Finally, current mode commands an output current rather than voltage, then the FB 1.276 V + CM3255 1MW 120pF Voltage Clamp C1 0.01µF R1 5 kW positive error-amp filter offers only a single pole to the feedback loop. This allows both a simpler compensation and a higher gain- Figure 8. Error Amplifier Equivalent Circuit bandwidth over a comparable voltage mode circuit. Oscillator and Shutdown The FB pin is directly connected to the inverting input of the positive error amplifier, whose nonincerting input is fed by the 1.276V reference. The amplifier is transconductance amplifier with a high output impedance of approximately 1M W, as shown in Figure 8. The V C pin is connected to the output of the error amplifiers and is internally clamped between 0.5V and 1.7V . A typical connection at the V C pin includes a capacitor in series with a resistor to ground, forming a pole / zero for loop compensation. An external shunt can be connected between the VC Sync Current Ramp VSW pin and ground to reduce its clamp voltage. GM3255 Without discrediting its apparent merits, current mode control comes with its own peculiar problems, and mainly subharmonic oscillation at duty cycles over 50%. The GM3255 family solves this problem by adopting a slope compensation scheme, in which, a fixed ramp generated by the oscillator is added to the current ramp. A proper slope rate is provided to improve circuit stability without sacrificing the advantages of current mode control. 7 Consequently, the current limit of the internal power transistor current is reduced from its nominal value. Switch Driver and Power Switch The switch driver receives a control signal from the logic section to drive the output power switch. The switch is grounded through emitter resistors (63mW total) to the PGND pin. PGND is not connected to the IC substrate so that switching noise can be isolated from the analog ground. The peak switching current is clamped by an internal circuit. The clamp current is guaranteed to be greater than 1.5A and varies with duty cycle due to slope compensation. The power switch can withstand a maximum voltage of 40V on the collector(VSW pin). The saturation voltage of the switch is typically less than 1V to minimize power dissipation. Short Circuit Condition When a short circuit condition happens in a boost circuit, the inductor current will increase during the whole switching cycle, causing excessive current to be drawn from the input power supply. Since control ICs don's have the means to limit load current, an external current limit circuit(such as a fuse or relay) has to be implemented to protect the load, power supply and ICs. When the FB pin voltage rises above 0.4V, the frequency increases to its nominal value, and the peak current begins to decrease as the output approaches the regulation voltage. The overshoot of the output voltage is prevented by the active pull-on, by which the sink current of the error amplifier is increased once an overvoltage condition is detected. The overvoltage condition is defined as when the FB pin voltage is 50mV greater than the reference voltage. COMPONENT SELECTION Frequency Compensation The goal of frequency compensation is to achieve desirable transient response and DC regulation while ensuring the stability of the system. A typical compensation network, as shown in Figure 9, provides a frequency response of two poles and one zero. This frequency response is further illustrated in the Bode plot shown in Figure 9. VC R1 GM3255 GM3255 can be activated by either connecting the VCC pin to a voltage source or by enabling the SS pin. GM3255 When the V CC voltage is below the minimum supply voltage, the VSW pin is in high impedance. Therefore, current conduces directly from the input power source to the output through the inductor and diode. Once VCC reaches approximately 1.5V, the internal power switch briefly turns on. This is a part of GM3255's normal operation. The turn-on of the power switch accounts for the initial current swing. 8 When the V C pin voltage rises above the threshold, the internal power switch starts to switch and a voltage pulse can be seen at the VSW pin. Detecting a low output voltage at the FB pin, the built-in frequency shift feature reduces the switching frequency to a fraction of its nominal value, reducing the minimum duty cycle, which is otherwise limited by the minimum on-time of the switch. The peak current during this phase is clamped by the internal current limit. C2 C1 In other topologies, the frequency shift built into the IC prevents damage to the chip and external components. This feature reduces the minimum duty cycle and allows the transformer secondary to absorb excess energy before the switch turns back on. GND Figure 9. A Typical Compensation Network The high DC gain in Figure 10 is desirable for achieving DC accuracy over ling and load variations. The DC gain of a transconductance error amplifier can be calculated as follows: GainDC = GM x RO Where: GM = error amplifier transconductance; RO = error amplifier output resistance 1MW The low frequency pole, fp1, is determined by the error amplifier output resistance and C1 as: 1 fP1 = 2pC1R O The first zero generated C1 and R1 is: 1 fz1 = 2pC1R1 The phase lead provided by this zero ensures that the loop has at least a 45°C phase margin at the crossover frequency. Therefore, this zero should be placed close to the pole generated in the power stage, which can be identified at frequency: fP1 = where: 1 2pCORLOAD CO = equivalent output capacitance of the error amplifier 120pF; RLOAD = load resistance. The high frequency pole, fP2, can be placed at the output filter's ESR zero or at half the switching frequency. Placing the pole at this frequency will cut down on switching noise. The frequency of this pole is determined by the value of C2 and R1: 1 fP2 = 2pC1R1 Magnetic Component Selection When choosing a magnetic component, one must consider factors such as peak current, core and ferrite material, output voltage ripple, EMI, temperature range, physical size, and cost. In boost circuits, the average inductor current is the product of output current and voltage gain (VOUT / VCC), assuming 100% energy transfer efficiency. In continuous conduction mode, inductor ripple current is IRIPPLE = VCC(VOUT - VCC) ( f )( L )(VOUT) fP1 fZ1 FP2 Frequency(LOG) Figure 10. Bode Plot of the Compensation Network Shown in Figure 9. VSW Voltage Limit In the boost topology, VSW pin maximum voltage is set by the maximum output voltage plus the output diode forward voltage. The diode forward voltage is typically 0.5V for Schottky diodes and 0.8V for ultrafast diodes VSW(MAX) = VOUT(MAX) + VF Where: VF = output diode forward voltage. In the flyback topology, peak VSW voltage is governed by: VSW(MAX) = VCC(MAX) + (VOUT + VF) X N Where: N = transformer turns ratio, primary over secondary where: f = 280kHz. The peak inductor current is equal to average current plus half of the ripple current, which should not cause inductor saturation. The above equation can also be referenced when selecting the value of the inductor based on the tolerance of the ripple current in the circuits. Small ripple current provides the benefits of small input capacitors and greater output current capability. A core geometry like a rod or barrel is prone to generating high magnetic field radiation, but is relatively cheap and small. Other core geometries, such as toroids, provide a closed magnetic loop to prevent EMI. Input Capacitor Selection In boost circuits, the inductor becomes part of the input filter, as shown in Figure 11. In continuous mode, the input current waveform is triangular and does not contain a large pulsed current, During continuous conduction mode, the peak to peak inductor ripple current is given in the previous section. In most applications, input capacitors in the range of 10µF to 100µF with an ESR less than 0.3W work well up to a full 1.5A switch current. GM3255 Gain (dB) DC Gain One simple method to ensure adequate phase margin is to design the frequency response with a - 20 dB per decade slope, until unity-gain crossover. The crossover frequency should be selected at the midpoint between fZ1 and fP2 where the phase margin is maximized. When the power switch turns off, there exists a voltage spike superimposed on top of the steady-state voltage. Usually, this voltage spike is caused by transformer leakage inductance charging stray capacitance between the VSW and PGND pins. To present the voltage at the VSW pin from exceeding the maximum rating, a transient voltage suppressor in series with a diode is paralleled with the primary windings. Another method of clamping switch voltage is to connect a transient voltage suppressor between the VSW pin and ground. 9 IL IIN VCC + - Reducing the Current Limit In some applications, the designer may prefer a lower limit on the switch current than 1.5A. An external shunt can be connected between the VC pin and ground to reduce its clamp voltage. Consequently, the current limit of the internal power transistor current is reduced from its nominal value. CIN RESR The voltage on the V C pin can be evaluated with the equation VC = ISWREAV Figure 11. Boost Circuit Effective Input Filter The situation is different in a flyback circuit. The input current is discontinuous and a significant pulse current is see by the input capacitors. Therefore, there are two requirements for capacitors in a flyback regulator: energy storage and filtering. To maintain a stable voltage supply to the chip, a storage capacitor larger than 20µF with low ESR is required. To reduce the noise generated by the inductor, insert a 1.0µF ceramic capacitor between VCC and ground as close as possible to the chip. When the power switch is turned on, I L is shunted to ground and IOUT discharges the output capacitor. When the IL ripple is small enough, IL can be treated as a constant and is equal to input current IIN, Summing up, the output voltage peak-peak ripple can be calculated by: (IIN - IOUT) (1 - D) VOUT(RIPPLE) = (COUT)(f) + IOUTD (COUT)(f) + IOUT(VOUT - VCC) (COUT)(f) x 1 (COUT)(f) (IOUT)(VOUT)(ESR) VCC GM3255 IRIPPLE = (IIN - IOUT)2 (1 - D) + (IOUT)2 (D) 10 V IN VCC R2 D1 VC R3 R1 C1 + IIN X ESR The capacitor RMS ripple current is: = IOUT A simple diode clamp, as shown in Figure12, clamps the VC voltage to a diode drop above the voltage on resistor R3. Unfortunately, such a simple circuit is not generally acceptable if VIN is loosely regulated. C2 The equation can be expressed more conveniently in terms of VCC, VOUT and IOUT for design purposes as follows: VOUT(RIPPLE) = where: R E = 0.063 W, the value of the internal emitter resistor; A V = 5V/ V, the gain of the current sense amplifier . Since R E and A V cannot be changed by the end user, the only available method for limiting switch current below 1.5A is to clamp the VC pin at a lower voltage. If the maximum switch or inductor current is substituted into the equation above, the desired clamp voltage will result. VOUT - VCC VCC Although the above equations apply only for boost circuits, similar equations can be derived for flyback circuits. Figure 12. Current Limiting using a Diode Clamp Another solution to the current limiting problem is to externally measure the current through the switch using a sense resistor. Such a circuit is illustrated in Figure 13. VCC VC PGND AGND VIN In some cases, SHM can rear its ugly head despite the presence of the onboard slope compensation. The simple cure to this problem is more slope compensation avoid the unwanted oscillation. In that case, an external circuit, shown in Figure 14, can be added to increase the amount of slope compensation used. This circuit requires only a few components and is "tacked on" to the compensation network. VSW + - VC R1 Q1 VSW C1 R2 C2 C3 Output Ground RSENSE R1 R2 C1 Figure 13.Current Limiting using a Current Sense Resistor C2 The switch current is limited to VBE(Q1) ISWITCH(PEAK) = R C3 R3 ESENSE Where: The improved circuit does not require a require a regulated voltage to operate properly. Unfortunately, a price must be paid for this convenience in the overall efficiency of the circuit. The designer should note that the input and output grounds are no longer common. Also, the addition of the current sense resistor, RSENSE, results in a considerable power loss which increase with the duty cycle. Resistor R2 and capacitor C3 form a low - pass filter to remove noise. Subharmonic Oscillation Subharmonic oscillation (SHM) is a problem found in Current-mode control systems, where instability results when duty cycle exceeds 50%. SHM only occurs in switching regulators with a continuous inductor current. This instability is not harmful to the converter and usually does not affect the output voltage regulation. SHM will increase the radiated EM noise from the converter and can cause, under certain circumstances, the inductor to emit high - frequency audile noise. SHM is an easily remedied problem. The rising slope of the inductor current is supplemented with internal “slope compensation” to prevent any duty cycle instability from carrying through to the next switching cycle. In the GM3255, slope compensation is added during the entire switch on-time, typically in the amount of 180 mA/µs. Figure 14. Technique for Increasing Slope Compensation The dashed box contains the normal compensation circuitry to limit the bandwidth of the error amplifier. Resistors R2 and R3 form a voltage divider off of the VSW pin. In normal operation VSW looks similar to a square wave, and is dependent on the converter topology. Formulas for calculating VSW in the boost and flyback topologies are given in the section "VSW Voltage Limit." The voltage on VSW charges capacitor C3 when the switch is off, causing the voltage at the VC pin to shift upwards. When the switch turns on, C3 discharges through R3, producing a negative slope at the VC pin. The negative slope provides the slope compensation. The amount of slope compensation added by this circuit is R3 DI = VSW ( R2 + R3 ) (1 - e DT -(1 - D) R3C3fSW fSW ) ( (1 - D) R A ) E V GM3255 V BE(Q1) = the base - emitter voltage drop of Q1, typically 0.65V. 11 Where: DI /DT = the amount of slope compensation added (A/s); VSW = the voltage at the switch node when the transistor is turned off (V); fSW = the switching frequency, typically 280kHz (GM3255) or 560kHz D = the duty cycle; RE = 0.063W, the value of the internal emitter resistor; AV = 5V/V, the gain of the current sense amplifier. In selecting appropriate values for the slope compensation network, the designer is advised to choose a convenient capacitor, then select values for R2 and R3 such that the amount of slope compensation added is 100mA /µs. Then R2 may increased or decreased as necessary. Of course, the series combination of R2 and R3 should be large enough to avoid drawing excessive current from VSW. Additionally, to ensure that the control loop stability is improved, the time constant formed by the additional components should be chosen such that R3C3 < 1-D fSW Finally, it is worth mentioning that the added slope compensation is a trade-off between duty cycle stability and transient response. The more slope compensation a designer adds, the slower the transient response will be, due to the external circuitry interfering with the proper operation of the error amplifier. Soft Start Through the addition of an external circuit, a soft-start function can be added to GM3255 of components. Soft-start circuitry prevents the VC pin from slamming high during startup, thereby inhibiting the inductor current from rising at a high slope. This circuit, shown in Figure 15, requires a minimum number of components and allows the soft-start circuitry to activate any time the SS pin is used to restart the converter. VIN VCC SS SS D1 Test 4 µA Test Q VC C3 GM3255 C1 12 R1 C2 Resistor R1 and capacitors C1 and C2 form the compensation network. At turn on, the voltage at the VC pin starts to come up, charging capacitor C3 through Schottky diode D2, clamping the voltage at the VC pin such that switching begins when VC reaches the VC threshold, typically 1.05V (refer to graphs for detail over temperature). VC = VF(D2) + VC3 Therefore, C3 slows the startup of the circuit by limiting the voltage on the VC pin. The soft- start time increases with the size of C3. Diode D1 discharges C3 when SS is low. If the shutdown function is not used with this part, the cathode of D1 should be connected to VIN. Calculating Junction Temperature To ensure safe operation of the GM3255, the designer must calculate the on-chip power dissipation and determine its expected junction temperature. Internal thermal protection circuitry will turn the part off once the junction temperature exceeds 180°C ± 30°C. However, repeated operation at such high temperatures will ensure a reduced operating life. Calculation of the junction temperature is an imprecise but simple task. First, the power losses must be quantified. There are three major sources of power loss on GM3255: Biasing of internal control circuitry, PBIAS Switch driver, PDRIVER Switch saturation, PSAT The internal control circuitry, including the oscillator and linear regulator, requires a small amount of power even when the switch is turned off. The specifications section of this datasheet reveals that the typical operating current IQ, due to this circuitry is 5.5 mA. Additional guidance can be found in the graph of operating current vs. temperature. This graph shows that IQ is strongly dependent on input voltage, VIN, and temperature. Then PBIAS = VINIQ Since the onboard switch is an NPN transistor, the base drive current must be factored in as well. This current is drawn from the VIN pin, in addition to the control circuitry current. The base drive current is listed in the specifications as DICC/DISW, or switch transconductance. As before the designer will find additional guidance in the graphs. With that information, the designer can calculate Figure 15. Soft Start PDRIVER = VINISW X ICC XD DISW 1 ISW(AVG) @ ILOAD X D X Efficiency D @ VOUT -VIN VOUT In a flyback converter, ISW(AVG) @ D@ VOUTILOAD 1 X Efficiency VIN VOUT VOUT + NS NP If T J approaches 150°C, the designer should consider possible means of reducing the junction temperature. Perhaps another converter topology could be selected to reduce the switch current. Increasing the airflow across the surface of the chip might be considered to reduce TA. Output Setting GM3255 develops a 1.276 V reference (V REF ) from the FB pin to ground. Output voltage is set by connecting the FB pin to an output resistor divider (Figure 16). The FB pin bias current represents a small error and can usually be ignored for values of R2 up to 7k. The suggested value for R2 is 6.19k. VOUT VIN The switch saturation voltage, V (CE)SAT , is the last major source of on-chip power loss. V(CE)SAT is the collector-emitter voltage of the internal NPN transistor when it is driven into saturation by its base drive current. The value for V(CE)SAT can be obtained from the specifications or from the graphs, as "Switch Saturation Voltage." Thus, PSAT @ V(CE)SATISW X D Finally, the total on-chip power losses are PD = PBIAS + PDRIVER + PSAT Power dissipation in a semiconductor device results in the generation of heat in the junctions at the surface of the chip. This heat is transferred to the surface of the IC package, but a thermal gradient exists due to the resistive properties of the package molding compound. The magnitude of the thermal gradient is expressed in manufacturers' data sheets as QJA, or junction-to- ambient thermal resistance. The on-chip junction temperature can be calculated if QJA, the air temperature near the surface of the IC, and the on-chip power dissipation are known. TJ = TA + (PDQJA) where: TJ = IC or FET junction temperature (°C); TA = ambient temperature (°C); PD = power dissipated by part in question(W); QJA = junction-to ambient thermal resistance (°C / W). For GM3255, QJA = 165°C / W. Once the designer has calculated TJ, the question of whether the GM3255 can be used in an application is settled. If TJ exceeds 150°C, the absolute maximum allowable junction temperature, the GM3255 is not suitable for that application. R1 FB PIN R2 VOUT = VREF (1 + R1 ) R2 V R1 = R2 ( OUT -1) 1.276 VREF Figure 16. Output Resistor Divider Circuit Layout Guidelines In any switching power supply, circuit layout is very important for proper operation. Rapidly switching currents combined with trace inductance generates voltage transitions that can cause problems. Therefore the following guidelines should be followed in the layout. 1. In boost circuits, high AC current circulates within the loop composed of the diode, output capacitor, and on-chip power transistor. The length of associated traces and leads should be kept as short as possible. In the flyback circuit, high AC current loops exist on both sides of the transformer. On the primary side, the loop consists of the input capacitor, transformer, and on-chip power transistor, while the transformer, rectifier diodes, and output capacitors form another loop on the secondary side. Just as in the boost circuit, all traces and leads containing large AC current should be kept short. 2. Separate the low current signal grounds from the power grounds. Use single point grounding or ground plane construction for the best results. 3. Locate the voltage feedback as near the IC as, possible to keep the sensitive feedback wiring short. Connect feedback resistors to the low current analog ground. GM3255 Where ISW = the current through the switch; D = the duty cycle or percentage of switch on-time. ISW and D are dependent on the type of converter. In a boost convert, 13 22 µH MBRS120T3 3.3 VIN 5.0 VO 10 µF PGND (7) GND 22 µF 3.6 k VCC (5) GND VSW (8) AGND (6) GM3255 VC (1) FB (2) 0.1 µF 1.3 k 200 pF 5.0 k Figure 17. Additional Application Diagram, 3.3 V Input, 5.0 V/ 400mA Output Boost Converter R2 4.87 k 2 C1 Test 3 NFB 0.01µF D1 C4 VSW VC GM3255 1 PGND AGND VOUT -12 V 8 + MBRS120T3 22µF 7 6 + L1 4 SS VCC 5 SS C3 22µF 22µH D2 MBRS120T3 VCC 5.0 V R3 1.27 k R1 5.0 k + C2 22µF Figure 18. Additional Application Diagram, 5.0V to -12V/ 75mA Inverting Converter MBRS140T3 VCC P6KE-15A + 22 µF -12 V T1 47 µF + 1.0 µF GND VCC (5) GND PGND (7) 1N4148 + 1:2 VSW (8) 47µF +12 V AGND (6) MBRS140T3 GM3255 VC (1 ) 47 nF FB (2) 1.28 k 10.72 k 4.7 nF GM3255 2.0 k 14 Figure 19. Additional Application Diagram, 2.7 to 13 V Input, ±12 V/ 200 mA Output Flyback Converter GND VCC (5) VC (1) GND 5.0 k 2.2 µF 1.1 k 22 µF GM3255 200 pF Low ESR 15 µH VSW (8) 0.01µF VIN -5.0 VOUT FB (2) AGND (6) PGND (7) 300 Figure 20. Additional Application Diagram, -9.0 V to -28 V Input, -5.0 V/700 mA Output Inverted Buck Converter 22 µH VCC 22 µF VCC (5) PGND (7) GND VSW (8) AGND (6) 5.0 V + 22 µF + GM3255 VC (1) 200 pF 37.24 k 22 µF 22 µF Low ESR FB (2) GND 0.01µF 5.0 k 12.76k Figure 21. Additional Application Diagram, 2.7 V to 28 V Input, 5.0 V Output SEPIC Converter R1 R2 1.245 k / 0.1 W, 1% 99.755k / 0.1 W, 1% GND C1 C10 C11 0.01µ 0.1µ R3 2.0 k 1 V C 2 FB 3 Test 4 SS GM3255 D1 VSW 8 PGND 7 6 AGND VCC 5 C2 0.1µ 50 V D1 D1 C3 0.1µ 50 V D1 D1 D1 0.1µ 50 V D1 100 VO 1N4148 C8 10 µ C9 0.1µ C7 0.1µ 50 V 1N4148 1N4148 1N4148 1N4148 1N4148 1N4148 C4 0.1µ 50 V C5 0.1µ 50 V C6 0.1µ 50 V GND 4.0 V GM3255 Figure 22. Additional Application Diagram, 4.0 V Input, 100 V/ 10 mA Output Boost Converter with Output Voltage Multiplier 15 200 pF D1 0.01 µF 1 V C VSW 8 2 FB PGND 7 GM3255 C6 C1 3 Test -12 V 22 µF L1 15 µH AGND 6 4 SS SS + R1 5.0 k VCC 5 +5.0 V C3 + 22 µF D3 D2 C4 0.1 µF GND GND C5 + 22 µF R2 R3 1.28 k 10.72 k +12 V Figure 23. Additional Application Diagram, 5.0 V Input, ±12 V Output Dual Boost Converter VIN 2.7V TO 16V T1 + C1 22 µF D2 P6KE-15A 5 OFF VIN ON 4 S/S VSW D3 1N4148 8 2 4 + • • 1 † –V -VOUT 3 -5 R2 2.49k 1% D1 MBRS130LT3 GM3255 C4 47 µF 3 NFB VC R3 2.49k 1% GND 1 6, 7 C2 0.047 µF R1 2k C3 0.0047 µF Figure 24. Positive to Negative Converter with Direct Feedback R1 13k 1% R2 1.21k 1% VIN 2.7V TO 13V OFF C1 22 µF 2, 3 P6KE-20A • FB ON 4 S/S VIN 8 VSW NFB VC GND 1 GM3255 C3 0.0047 µF 5 + 5 2 GM3255 16 MBRS140T3 T1 + C2 0.047 µF R3 2k 6, 7 3 1N4148 6, 7 •4 8 + • 1 MBRS140T3 VOUT 15V C4 47 µF C5 47 µF -V OUT -15V R4 12.1k 1% R5 2.49k 1% Figure 25. Dual Output Flyback Converter with Over Voltage Protetion V OUT -3 V 250mA L1 VIN 5V 2 3 1 4 R1 1k 1% C2 47 µF 16V C1 22 µF 10V 5 V IN 4 S/S 7 GND 6 GND S VSW GM3255 + NFB VC 8 + C6 0.1 µF 3 1 D1 + C5 0.0047µF R4 2k C4 0.047µF C3 47µF 16V R2 4.99k 1% Figure 26. Low Ripple 5V to -3V "Cuk" Converter 5mA MAX LAMP 10 C2 27pF T1 VIN 4.5V TO 30V + 5 4 3 10 µF 2 1 D1 1N4148 C1 0.1 µF Q1 Q2 330 W 2.7V TO 5.5V + 2.2 µF ON 4 S/S OFF 5 VIN 562 W* 8 VSW 10k 20k GM3255 DIMMING VFB VC + 1 GND 6, 7 D2 1N4148 L1 33 µF 1N5818 2 0.1 µF 22k 1N4148 2 µF OPTIONAL REMOTE DIMMING Figure 27. CCFL Supply VIN 4V TO 9V L1A 10 µH ON 4 V IN S/S OFF V SW GM3255 + C1 33 µF 20V FB GND 6, 7 MBRS130LT3 V OUT 8 2 VC L1B 10 µH 1 R1 2k C4 0.047µF R2 18.7k 1% C2 1 µF C5 0.0047µF R3 6.19k 1% 5V + C3 100 µF 10V GM3255 5 17 Figure 28. 2 Li - Lion Cell to 5V SEPIC Converter SOP-8 PACKAGE OUTLINE DIMENSIONS 0.008 +0.0018 -0.0005 0.200 +0.05 -0.01 0 ° ~ 8° 0.028 0.710 +0.013 -0.022 Pad Layout +0.33 -0.56 0.060 1.52 0.236 ± 0.008 5.990 +0.21 -0.20 0.154 +0.003 -0.004 0.275 0.155 7.0 4.0 PIN INDENT 3.91 ± 0.1 0.024 0.050 0.6 1.270 Inches ( mm ) 0.063 ± 0.005 1.600 ± 0.130 0.191 +0.002 -0.004 4.850 +0.05 -0.10 0.057 NOM 1.450 NOM ( Inches ) mm 0.007 ± 0.003 0.175 ± 0.075 0.050 NOM 1.270 NOM 0.016 +0.004 -0.003 0.410 +0.10 -0.08 NSOP-8 PACKAGE OUTLINE DIMENSIONS GM3255 90 X 90 95 X 130 18 Exposed Pad Version Only ORDERING NUMBER GM 3255 S8 R Circuit Type Shipping R: Tape & Reel Package S8: SO-8 NS8: NSOP-8 GM3255 Gamma Micro. 19