CEL UPB1509GV-E1-A

BIPOLAR DIGITAL INTEGRATED CIRCUIT
UPB1509GV
NEC's 1.0 GHz
DIVIDE BY 2/4/8 PRESCALER
TEST CIRCUIT
FEATURES
• HIGH FREQUENCY OPERATION TO 1 GHz
VCC
• SELECTABLE DIVIDE RATIO: ÷2, ÷4, ÷8
• WIDE SUPPLY VOLTAGE RANGE: 2.2 TO 5 V
C
C
• LOW SUPPLY CURRENT: 5.3 mA
• SMALL PACKAGE: 8 pin SSOP
• AVAILABLE IN TAPE AND REEL
C
fIN
C
1 VCC1
VCC2 8
2 IN
OUT 7
3 IN
SW2 6
C
VOUT
C
DESCRIPTION
4 GND
NEC's UPB1509GV is a Silicon RFIC digital prescaler manufactured with the NESAT™ IV silicon bipolar process. It features frequency response to 1 GHz, selectable divide-by-two,
four, or eight modes, and operates from a 3 to 5 volt supply
while drawing only 5.3 milliamps. The device is housed in a
small 8 pin SSOP package that contributes to system miniaturization. The low power consumption and wide supply range
makes the device well suited for cellular and cordless telephones as well as DBS receiver applications.
SW1 5
C
C = 1000 pF
ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 2.2 to 5.5 V, unless otherwise noted)
PART NUMBER
PACKAGE OUTLINE
SYMBOLS
UNITS
MIN
TYP
MAX
Supply Current, No Input Signal, Vcc = 3 V
mA
3.5
5.0
5.9
fIN (u)
Upper Limit Operating Frequency, PIN = -20 to 0 dBm
PIN = -20 to -5 dBm at ÷ 2
at ÷ 4
at ÷ 8
MHz
MHz
MHz
MHz
500
700
800
1000
fIN (L)
Lower Limit Operating Frequency, PIN = -20 to 0 dBm
PIN = -20 to -5 dBm
MHz
MHz
Input Power, fIN = 50 to 1000 MHz
fIN = 50 to 500 MHz
dBm
dBm
-20
-20
VP-P
0.1
ICC
PIN
PARAMETERS AND CONDITIONS
UPB1509GV
S08
50
500
-5
0
VOUT
Output Voltage, RL = 200 Ω
VIN(H)
Division Ratio Control Voltage High
V
VCC
VIN(L)
Division Ratio Control Voltage Low
V
OPEN
The information in this document is subject to change without notice. Before using this document, please confirm
that this is the latest version.
Date Published: June 28, 2005
0.2
UPB1509GV
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C)
SYMBOLS
PARAMETERS
VCC1, VCC2 Supply Voltage
RECOMMENDED
OPERATING CONDITIONS
UNITS
RATINGS
V
6.0
SYMBOL
V
6.0
VCC1, VCC2 Supply Voltage
mW
250
VIN
Input Voltage
PD
Power Dissipation2
TOP
Operating Temperature
°C
-45 to +85
TSTG
Storage Temperature
°C
-55 to +150
TOP
PARAMETER
UNITS MIN TYP MAX
Operating Temperature
V
2.2
3.0
5.5
°C
-40
+25
+85
Notes:
1. Operation in excess of any one of these parameters may result
in permanent damage.
2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy
glass PWB (TA = +85˚C).
INTERNAL BLOCK DIAGRAM
D Q
CLK
Q
IN
IN
D Q
CLK
Q
D Q
CLK
Q
SW1
SW2
OUT
PIN DESCRIPTIONS
Pin No.
Symbol
Applied
Voltage
Pin
Voltage
Description
1
VCC1
2.2 to 5.5
–
Power supply pin of input amplifier and dividers. This pin must be
equipped with bypass capacitor (eg 1000 pF) to ground.
2
IN
–
1.7 to 4.95
Signal input pin. This pin should be coupled with a capacitor (eg 1000 pF).
3
IN
–
1.7 to 4.95
Signal input bypass pin. This pin must be equipped with a bypass
capacitor (eg 1000 pF) to ground.
4
GND
0
–
Ground pin. Ground pattern on the board should be formed as wide as
possible to minimize ground impedance.
5
SW1
H/L
(VCC/OPEN)
–
Divided ratio control pin. Divide ratio can be controlled by the following
input voltages to these pins.
6
SW2
H/L
SW2
(VCC/OPEN)
H (VCC)
L (OPEN)
H (VCC)
1/2
1/4
L (OPEN)
1/4
1/8
SW1
These pins must each be equipped with a bypass capacitor to ground.
7
OUT
–
1.0 to 4.7
8
VCC2
2.2 to 5.5
–
Divided frequency output pin. This pin is designed as an emitter follower
output. This pin can output 0.1 Vp-p min with a 200 Ω load.
This pin should be coupled to load device with a capacitor (eg 1000 pF).
Power supply pin of output buffer amplifier. This pin must be equipped
with bypass capacitor (eg 1000 pF) to ground.
UPB1509GV
TYPICAL PERFORMANCE CURVES
(TA = +25°C unless otherwise noted)
CIRCUIT CURRENT vs.
SUPPLY VOLTAGE and TEMPERATURE
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
9
+20
+10
TA = -40°C
VCC = 3.0 V
7
Input Power, PIN (dBm)
Circuit Current, ICC (mA)
8
6
TA = +25°C
5
TA = +85°C
4
3
Recommended operating range
2
VCC = 5.5 V
0
Guaranteed
Operating Window
-10
-20
VCC = 2.2 V
-30
-40
VCC = 3.0 V
-50
1
0
1
2
3
4
5
VCC = 5.5 V
TA = +25¡C
-60
0
VCC = 2.2 V
10
6
1000 2000
100
Supply Voltage, VCC (V)
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
+20
+10
+10
TA = +25°C
TA = -40°C
TA = +85°C
Input Power, PIN (dBm)
Input Power, PIN (dBm)
TA = +25°C
0
Guaranteed
operating window
-10
-20
TA = +85°C
-30
-40
-20
-30
TA = +85°C
-40
TA = -40°C
-50
TA = +25°C
VCC = 3.0 V
1000 2000
100
10
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
VCC = 3.0 V
PIN = 0 dBm
OutputVoltage Swing, VP-P (V)
TA = +25°C
TA = -40°C
TA = +85°C
+10
Input Power, PIN (dBm)
1000 2000
100
Input Frequency, fin (MHz)
+20
0
Guaranteed
operating window
-10
-20
-30
TA = +85°C
-40
TA = -40°C
-50
TA = +25°C
-60
TA = +25°C
VCC = 2.2 V
-60
10
TA = -40°C
Guaranteed
operating window
-10
TA = -40°C
-50
-60
TA = +85°C
0
VCC = 5.5 V
10
0.3
TA = +85°C
TA = +25°C
TA = +25°C
0.2
TA = -40°C
TA = +85°C
TA = -40°C
0.1
0
100
Input Frequency, fin (MHz)
1000 2000
10
100
Input Frequency, fin (MHz)
1000 2000
UPB1509GV
TYPICAL PERFORMANCE CURVES
(TA = +25°C unless otherwise noted)
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
TA = -40°C
PIN = 0 dBm
VCC = 5.5 V
OutputVoltage Swing, VP-P (V)
OutputVoltage Swing, VP-P (V)
TA = +25°C
PIN = 0 dBm
0.3
VCC = 3.0 V
0.2
VCC = 2.2 V
0.1
0
VCC = 5.5 V
0.3
VCC = 3.0 V
0.2
VCC = 2.2 V
0.1
0
10
100
1000 2000
10
100
Input Frequency, fin (MHz)
1000 2000
Input Frequency, fin (MHz)
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
OutputVoltage Swing, VP-P (V)
TA = +85°C
PIN = 0 dBm
VCC = 5.5 V
0.3
VCC = 3.0 V
0.2
VCC = 2.2 V
0.1
0
10
100
1000 2000
Input Frequency, fin (MHz)
Divide by 4 mode
(Guaranteed operating window: VCC = 2.2 to 5.5 V, TA = -40 to +85°C)
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
+20
+10
TA = +85°C
+10
TA = -40°C
0
Input Power, PIN (dBm)
Input Power, PIN (dBm)
VCC = 5.5 V
VCC = 3.0 V
VCC = 2.2 V
Guaranteed
Operating Window
-10
-20
VCC = 2.2 V
-30
-40
VCC = 5.5 V
VCC = 3.0 V
-50
-60
TA = +25ºC
10
Input Frequency, fin (MHz)
Guaranteed
operating window
-10
-20
TA = +85°C
-30
-40
TA = -40°C
-50
VCC = 5.5 V
100
TA = +25°C
0
-60
1000 2000
VCC = 3.0 V
10
TA = +25°C
100
1000 2000
Input Frequency, fin (MHz)
UPB1509GV
TYPICAL PERFORMANCE CURVES
(TA = +25°C unless otherwise noted)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
+20
TA = +85°C
+10
TA = +25°C
TA = -40°C
0
Input Power, PIN (dBm)
Input Power, PIN (dBm)
+10
Guaranteed
operating window
-10
-20
TA = +85°C
-30
-40
TA = -40°C
TA = -40°C
Guaranteed
operating window
-10
-20
TA = -40°C
-30
TA = +85°C
-40
TA = +25°C
-60
TA = -40°C
-50
-50
VCC = 3.0 V
10
1000 2000
100
TA = +25°C
VCC = 5.5 V
-60
10
TA = +85°C
TA = +25°C
0
1000 2000
100
Input Frequency, fin (MHz)
Input Frequency, fin (MHz)
Divide by 8 mode
(Guaranteed operating window: VCC = 2.2 to 5.5 V, TA = -40 to +85 °C)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
+20
+10
+10
TA = +25°C
VCC = 5.5 V
VCC = 2.2 V
VCC = 3.0 V
0
Input Power, PIN (dBm)
Input Power, PIN (dBm)
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
Guaranteed
Operating Window
-10
-20
VCC = 2.2 V
-30
-40
Guaranteed
operating window
-10
-20
-30
TA = +85°C
-40
TA = -40°C
-50
-50
-60
TA = +25°C
10
VCC = 5.5 V
VCC = 3.0 V
-60
10
1000 2000
100
TA = +85°C
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
TA = +25°C
+10
+10
TA = -40°C
Input Power, PIN (dBm)
TA = -40°C
0
TA = +25°C
Guaranteed
operating window
-10
-20
TA = +85°C
-30
-40
TA = -40°C
-50
0
TA = +85°C
TA = +25°C
Guaranteed
operating window
-10
-20
-30
TA = +85°C
-40
TA = -40°C
-50
TA = +25°C
-60
VCC = 2.2 V
10
-60
100
Input Frequency, fin (MHz)
1000 2000
100
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
TA = +25°C
VCC = 3.0 V
Input Frequency, fin (MHz)
Input Power, PIN (dBm)
TA = -40°C
TA = +85°C
TA = -40°C
0
1000 2000
TA = +25°C
VCC = 5.5 V
10
100
Input Frequency, fin (MHz)
1000 2000
UPB1509GV
TYPICAL SCATTERING PARAMETERS
(TA = 25°C)
S11 vs. INPUT FREQUENCY
VCC1 = VCC2 = 3.0 V, SW1 = SW2 = 3.0 V
FREQUENCY
S11
REF 1.0 Units/
2
200.0 mUnits/
55.375 Ω -142.79 Ω
MARKER 2
700.0 MHZ
1
2
3
START 0.050000000 GHz
STOP 1.000000000 GHz
S22 vs. OUTPUT FREQUENCY
S22
REF 1.0 Units
200.0 mUnits/
Z
50 MHz
149.09 Ω + j 14.86 Ω
350 MHz
194.21 Ω – j 36.64 Ω
START 0.050000000 GHz
STOP 0.350000000 GHz
S11
GHz
MAG
ANG
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.929
0.898
0.866
0.840
0.834
0.819
0.803
0.792
0.787
0.771
-6.7
-10.5
-13.6
-15.9
-19.1
-21.9
-24.7
-27.0
-30.0
-32.7
UPB1509GV
SYSTEM APPLICATION EXAMPLE
DEMO
RX
VCO
SW
N
PLL
PLL
N
µPB1509GV
I
0¡
TX
I
Q
¿
PA
90¡
Q
OUTLINE DIMENSIONS (Units in mm)
PACKAGE OUTLINE S08
7
8
6
5
1
8
2
7
3
6
4
5
1509
Detail of Lead End
N
1
2
3
3.0 MAX
+7˚
4
3 -3˚
4.94 ± 0.2
+0.10
0.15 -0.05
1.5±0.1
0.87±0.2
3.2±0.1
1.8 MAX
0.1 ± 0.1
0.65
+0.10
0.3 -0.05
0.5 ± 0.2
0.575 MAX
0.15
PIN CONNECTIONS
1. VCC1
5. SW1
2. IN
6. SW2
3. IN
7. OUT
4. GND
8. VCC2
ORDERING INFORMATION (Solder Contains Lead)
PART NUMBER
QUANTITY
UPB1509GV-E1
1000/Reel
ORDERING INFORMATION (Pb-Free)
PART NUMBER
QUANTITY
UPB1509GV-E1-A
1000/Reel
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
A Business Partner of NEC Compound Semiconductor Devices, Ltd.
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS
Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A
Not Detected
Lead (Pb)
< 1000 PPM
Mercury
< 1000 PPM
Not Detected
Cadmium
< 100 PPM
Not Detected
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.