SGLS243A − APRIL 2004 − REVISED JUNE 2008
D Low-Noise Operation Antiringing Switch
FEATURES
D Qualified for Automotive Applications
D High-Efficiency Synchronous Step-Down
D
D
D
D
D
D
D
D
D
D
D
Converter With Greater Than 95%
Efficiency
2-V to 5.5-V Operating Input Voltage Range
Adjustable Output Voltage Range From
0.8 V to VI
Fixed Output Voltage Options Available in
0.9 V, 1 V, 1.2 V, 1.5 V, 1.8 V, 1.9 V, 2.5 V, and
3.3 V
Synchronizable to External Clock Signal up
to 1 MHz
Up to 600-mA Output Current
Pin-Programmable Current Limit
High Efficiency Over a Wide Load Current
Range in Power Save Mode
100% Maximum Duty Cycle for Lowest
Dropout
D
and PFM/PWM Operation Mode
Internal Softstart
50-µA Quiescent Current (TYP)
Available in the 10-Pin Microsmall Outline
Package (MSOP)
Evaluation Module Available
APPLICATIONS
D
D
D
D
D
D
Low-Power CPUs and DSPs
Cellular Phones
Organizers, PDAs, and Handheld PCs
MP-3 Portable Audio Players
Digital Cameras
USB-Based DSL Modems and Other
Network Interface Cards
description/ordering information
The TPS6200x devices are a family of low-noise synchronous step-down dc-dc converters that are ideally
suited for systems powered from a 1-cell Li-ion battery or from a 2- to 3-cell NiCd, NiMH, or alkaline battery. The
TPS6200x operates typically down to an input voltage of 1.8 V, with a specified minimum input voltage of 2 V.
ORDERING INFORMATION{
TJ
VOLTAGE OPTIONS
MSOP PACKAGE}
MARKING
Adjustable
TPS62000QDGSRQ1
TPS62001QDGSRQ1§
AOQ
0.9 V
1.2 V
TPS62002QDGSRQ1§
TPS62003QDGSRQ1§
1.5 V
TPS62004QDGSRQ1
AOR
1.8 V
ALY
1.9 V
TPS62005QDGSRQ1
TPS62008QDGSRQ1§
2.5 V
TPS62006QDGSRQ1
AOS
3.3 V
TPS62007QDGSRQ1
1V
−40°C
−40
C to 125°C
125 C
AOT
† For the most current package and ordering information, see the Package Option
Addendum at the end of this document, or see the TI web site at http://www.ti.com.
‡ Package drawings, thermal data, and symbolization are available at
http://www.ti.com/packaging.
§ Indicates Product Preview. Contact Texas Instruments for details.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2008, Texas Instruments Incorporated
!"# $%&'()* &%*+"*# ,, "*-%.(+"%* &'..)* +# %- /'01"&+"%* $+)2 .%$'&# &%*-%.( %
#/)&"-"&+"%*# /). !) ).(# %- )3+# *#.'()*# #+*$+.$ 4+..+*52
.%$'&"%* /.%&)##"*6 $%)# *% *)&)##+."15 "*&1'$) )#"*6 %- +11
/+.+()).#2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SGLS243A − APRIL 2004 − REVISED JUNE 2008
description (continued)
The TPS6200x is a synchronous current-mode PWM converter with integrated N- and P-channel power
MOSFET switches. Synchronous rectification is used to increase efficiency and to reduce external component
count. To achieve the highest efficiency over a wide load current range, the converter enters a power-saving
pulse-frequency modulation (PFM) mode at light load currents. Operating frequency is typically 750 kHz,
allowing the use of small inductor and capacitor values. The device can be synchronized to an external clock
signal in the range of 500 kHz to 1 MHz. For low-noise operation, the converter can be operated in the PWM
mode and the internal antiringing switch reduces noise and EMI. In the shutdown mode, the current
consumption is reduced to less than 1 µA. The TPS6200x is available in the 10-pin (DGS) microsmall outline
package (MSOP). The devices operate over a junction temperature range of −40°C to 125°C.
EFFICIENCY
vs
LOAD CURRENT
100
VI = 2 V
to 5.5 V
90
1
VIN
L
EN
FB
9
10 µH
VO = 0.8 V
to VI
80
10 µF
Efficiency − %
70
8
SYNC = Low
6
SYNC = High
50
7
ILIM
40
SYNC
GND
30
3
PGND
PG
FC
10
4
PG
2
0.1 µF
20
VI = 3.6 V,
VO = 2.5 V
10
0.1
1
10
100
IO − Load Current − mA
† With VO ≥1.8 V; Co = 10 µF, VO <1.8 V; Co = 47 µF
1000
Figure 1
Figure 2. Typical Application Circuit for Fixed
Output Voltage Option
MSOP (DGS) PACKAGE
(TOP VIEW)
VIN
FC
GND
PG
FB
2
10 µF
TPS6200x
60
0
5
1
10
2
9
3
8
4
7
5
6
POST OFFICE BOX 655303
PGND
L
EN
SYNC
ILIM
• DALLAS, TEXAS 75265
†
SGLS243A − APRIL 2004 − REVISED JUNE 2008
functional block diagram
PG
FC (See Note B)
VIN
10 Ω
Undervoltage
Lockout
Bias Supply
EN
+
_
R1
PFM/PWM
Comparator
_
+
Soft
Start
+
PFM/PWM
Control Logic
Current Limit
Logic
Driver
Shoot-Through
Logic
N-Channel
Power MOSFET
EN
+
_
L
Compensation
R2
R1 + R2 ≈ 1 MΩ
P-Channel
Power MOSFET
PFM/PWM
Mode Select
Error Amplifier
_
FB
(See
Note A)
Current
Sense
Slope Compensation
Power Good
Vref = 0.45 V
Sync
+
Oscillator
Load Comparator
+
_
Current Sense
+
Offset
PGND
Antiringing
FB
GND
SYNC
ILIM
NOTES: A. The adjustable output voltage version does not use the internal feedback resistor divider. The FB pin is directly connected to the
error amplifier.
B. Do not connect the FC pin to an external power source.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SGLS243A − APRIL 2004 − REVISED JUNE 2008
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
EN
8
I
Enable. A logic high enables the converter and a logic low forces the device into shutdown mode reducing the supply
current to less than 1 µA.
FB
5
I
Feedback pin for the fixed output voltage option. For the adjustable version, an external resistive divider is connected
to FB. The internal voltage divider is disabled for the adjustable version.
FC
2
GND
3
ILIM
6
I
L
9
I/O
Connect the inductor to this pin. L is the switch pin connected to the drain of the internal power MOSFETS.
PG
4
O
Power good comparator output. This is an open-drain output. A pullup resistor should be connected between PG
and VO. The output goes active high when the output voltage is greater than 92% of the nominal value.
PGND
10
SYNC
7
I
Input for synchronization to external clock signal. Synchronizes the converter switching frequency to an external
clock signal with CMOS level:
SYNC = High: Low-noise mode enabled, fixed frequency PWM operation is forced
SYNC = Low (GND): Power-save mode enabled, PFM/PWM mode enabled.
VIN
NC
1
I
Supply voltage input
Supply bypass pin. A 0.1-µF coupling capacitor should be connected as close as possible to this pin for good high
frequency input voltage supply filtering.
Ground
Switch current limit. Connect ILIM to GND to set the switch current limit to typically 600 mA, or connect this pin to
VIN to set the current limit to typically 1200 mA.
Power ground. Connect all power grounds to PGND.
Not connected
detailed description
operation
The TPS6200x is a step down converter operating in a current mode PFM/PWM scheme with a typical switching
frequency of 750 kHz.
At moderate to heavy loads, the converter operates in the pulse width modulation (PWM) and at light loads the
converter enters a power save mode (pulse frequency modulation) to keep the efficiency high.
In the PWM mode operation, the device operates at a fixed frequency of 750 kHz. At the beginning of each clock
cycle, the high side P-channel MOSFET is turned on. The current in the inductor ramps up and is sensed via
an internal circuit. The high side switch is turned off when the sensed current causes the PFM/PWM comparator
to trip when the output voltage is in regulation or when the inductor current reaches the current limit (set by ILIM).
After a minimum dead time preventing shoot through current, the low side N-channel MOSFET is turned on and
the current ramps down again. As the clock cycle is completed, the low side switch is turned off and the next
clock cycle starts.
In discontinuous conduction mode (DCM), the inductor current ramps to zero before the end of each clock cycle.
In order to increase the efficiency the load comparator turns off the low side MOSFET before the inductor current
becomes negative. This prevents reverse current flowing from the output capacitor through the inductor and
low side MOSFET to ground that would cause additional losses.
As the load current decreases and the peak inductor current does not reach the power save mode threshold
of typically 120 mA for more than 15 clock cycles, the converter enters a pulse frequency modulation (PFM)
mode.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SGLS243A − APRIL 2004 − REVISED JUNE 2008
operation (continued)
In the PFM mode, the converter operates with:
D Variable frequency
D Constant peak current that reduces switching losses
D Quiescent current at a minimum
Thus maintaining the highest efficiency at light load currents. In this mode, the output voltage is monitored with
the error amplifier. As soon as the output voltage falls below the nominal value, the high side switch is turned
on and the inductor current ramps up. When the inductor current reaches the peak current of typical: 150 mA
+ 50 mA/V x (VI − VO), the high side switch turns off and the low side switch turns on. As the inductor current
ramps down, the low side switch is turned off before the inductor current becomes negative which completes
the cycle. When the output voltage falls below the nominal voltage again, the next cycle is started.
The converter enters the PWM mode again as soon as the output voltage can not be maintained with the typical
peak inductor current in the PFM mode.
The control loop is internally compensated reducing the amount of external components.
The switch current is internally sensed and the maximum current limit can be set to typical 600 mA by connecting
ILIM to ground or to typically 1.2 A connecting ILIM to VIN.
100% duty cycle operation
As the input voltage approaches the output voltage and the duty cycle exceeds typical 95%, the converter turns
the P-channel high side switch continuously on. In this mode, the output voltage is equal to the input voltage
minus the voltage drop across the P-channel MOSFET.
synchronization, power save mode and forced PWM mode
If no clock signal is applied, the converter operates with a typical switching frequency of 750 kHz. It is possible
to synchronize the converter to an external clock within a frequency range from 500 kHz to 1000 kHz. The device
automatically detects the rising edge of the first clock and is synchronizes immediately to the external clock.
If the clock signal is stopped, the converter automatically switches back to the internal clock and continues
operation without interruption. The switch over is initiated if no rising edge on the SYNC pin is detected for a
duration of four clock cycles. Therefore, the maximum delay time can be 8 µs in case the internal clock has a
minimum frequency of 500 kHz.
In case the device is synchronized to an external clock, the power save mode is disabled and the device stays
in forced PWM mode.
Connecting the SYNC pin to the GND pin enables the power save mode. The converter operates in the PWM
mode at moderate to heavy loads and in the PFM mode during light loads maintaining high efficiency over a
wide load current range.
Connecting the SYNC pin to the VIN pin forces the converter to operate permanently in the PWM mode, even
at light or no load currents. The advantage is the converter operates with a fixed switching frequency that allows
simple filtering of the switching frequency for noise sensitive applications. In this mode, the efficiency is lower
compared to the power save mode during light loads (see Figure 1).
It is possible to switch from forced PWM mode to the power save mode during operation.
The flexible configuration of the SYNC pin during operation of the device allows efficient power management
by adjusting the operation of the TPS6200x to the specific system requirements.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SGLS243A − APRIL 2004 − REVISED JUNE 2008
low noise antiringing switch
An antiringing switch is implemented in order to reduce the EMI radiated from the converter during
discontinuous conduction mode (DCM). In DCM, the inductor current ramps to zero before the end of each
switching period. The internal load comparator turns off the low side switch at that instant thus preventing the
current flowing backward through the inductance which increases the efficiency. An antiringing switch across
the inductor prevents parasitic oscillation caused by the residual energy stored in the inductance (see
Figure 12).
NOTE:
The antiringing switch is only activated in the fixed output voltage versions. It is not enabled for the
adjustable output voltage version TPS62000.
soft start
As the enable pin (EN) goes high, the soft-start function generates an internal voltage ramp. This causes the
start-up current to slowly rise preventing output voltage overshoot and high inrush currents. The soft-start
duration is typical 1 ms (see Figure 13). When the soft-start function is completed, the error amplifier is
connected directly to the internal voltage reference.
enable
Logic low on EN forces the TPS6200x into shutdown. In shutdown, the power switch, drivers, voltage reference,
oscillator, and all other functions are turned off. The supply current is reduced to less than 1 µA in the shutdown
mode.
undervoltage lockout
An undervoltage lockout circuit provides the save operation of the device and it prevents the converter from
turning on when the voltage on VIN is less than 1.6 V typical.
power good comparator
The power good (PG) comparator has an open drain output capable of sinking typically 10 µA. The PG is only
active when the device is enabled (EN = high). When the device is disabled (EN = low), the PG pin is high
impedance.
The PG output is only valid after a 100 µs delay after the device is enabled and the supply voltage is greater
than 1.2 V. This is only important in cases where the pullup resistor of the PG pin is connected to an external
voltage source, which might cause an initial spike (false high signal) within the first 100 µs after the input voltage
exceeds 1.2 V. This initial spike can be filtered with a small R-C filter to avoid false power good signals during
start-up.
If the PG pin is connected to the output of the TPS62000 with a pullup resistor, no initial spike (false high signal)
occurs and no precautions have to be taken during start-up.
The PG pin becomes active high when the output voltage exceeds typically 94.5% of its nominal value. Leave
the PG pin unconnected when not used.
no load operation
In case the converter operates in the forced PWM mode and there is no load connected to the output, the
converter regulates the output voltage by allowing the inductor current to reverse for a short period of time.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SGLS243A − APRIL 2004 − REVISED JUNE 2008
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltages on pin VIN and FC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Voltages on pins EN, ILIM, SYNC, PG, FB, L (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VIN + 0.3 V
Peak switch current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 A
Continuous power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature (soldering, 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
10 pin MSOP
555 mW
5.56 mW/°C
305 mW
221 mW
NOTE: The thermal resistance junction to ambient of the 10-pin MSOP is 180°C/W. The device will not
run into thermal limitations, provided it is operated within the specified range.
recommended operating conditions
MIN
Supply voltage, VI
TYP
MAX
UNIT
2
5.5
V
0.8
V
Output current for 3-cell operation, IO (VI ≥ 2.5 V; L = 10 µH, f = 750 kHz)
VI
600
mA
Output current for 2-cell operation, IO (VI ≥ 2 V; L = 10 µH, f = 750 kHz)
200
mA
Output voltage range for adjustable output voltage version, VO
Inductor, L (see Note 2)
µH
10
Input capacitor, Ci (see Note 2)
10
µF
Output capacitor, Co (see Note 2) VO ≥ 1.8 V)
10
µF
Output capacitor, Co (see Note 2) VO < 1.8 V)
µF
47
Operating junction temperature, TJ
-40
125
°C
NOTE 2: See the Application Information section for further information.
electrical characteristics over recommended operating free-air temperature range, VI = 3.6 V,
VO = 2.5 V, IO = 300 mA, EN = VIN, ILIM = VIN, TJ = −40°C to 125°C (unless otherwise noted)
supply current
PARAMETER
VI
I(Q)
I(SD)
Input voltage range
TEST CONDITIONS
IO = 0 mA to 600 mA
IO = 0 mA to 200 mA
Operating quiescent current
Shutdown current
MIN
TYP
MAX
2.5
5.5
2
5.5
IO = 0 mA, SYNC = GND (PFM-mode enabled)
EN = GND
UNIT
V
50
75
µA
0.1
1
µA
TYP
MAX
enable
PARAMETER
VIH
VIL
EN high-level input voltage
Ilkg
V(UVLO)
EN input leakage current
TEST CONDITIONS
MIN
1.3
V
EN low level input voltage
EN = GND or VIN
Undervoltage lockout threshold
1.2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
0.4
V
0.01
0.1
µA
1.6
1.95
V
7
SGLS243A − APRIL 2004 − REVISED JUNE 2008
electrical characteristics over recommended operating free-air temperature range, VI = 3.6 V,
VO = 2.5 V, IO = 300 mA, EN = VIN, ILIM = VIN, TJ = −40°C to 125°C (unless otherwise noted) (continued)
power switch and current limit
PARAMETER
TEST CONDITIONS
VI = VGS = 3.6 V,
VI = VGS = 2 V,
P-channel MOSFET on-resistance
P-channel leakage current
VDS = 5.5 V
VI = VGS = 3.6 V,
rDS(on)
N-channel MOSFET on-resistance
I(LIM)
P-channel current limit
VIH
VIL
ILIM high-level input voltage
Ilkg
ILIM input leakage current
TYP
MAX
150
280
600
I = 200 mA
1
280
UNIT
mΩ
480
IO = 200 mA
IO = 200 mA
150
2.5 V ≤ VI ≤ 5.5 V,
ILIM = VIN
800
1200
1600
2 V ≤ VI ≤ 5.5 V,
ILIM = GND
390
600
900
VI = VGS = 2 V,
VDS = 5.5 V
N-channel leakage current
I = 200 mA
MIN
µA
600
mΩ
500
1
1.3
µA
mA
V
ILIM low-level input voltage
0.4
V
0.01
0.1
µA
MIN
TYP
MAX
UNIT
88%
VO
92%
VO
94%
VO
V
ILIM = GND or VIN
power good output (see Note 3)
PARAMETER
V(PG)
TEST CONDITIONS
Power good threshold
Feedback voltage falling
Power good hysteresis
VOL
Ilkg
2.5% VO
V(FB) = 0.8 × VO nominal, I(sink) = 10 µA
V(FB) = VO nominal
PG output low voltage
PG output leakage current
Minimum supply voltage for valid power good signal
V
0.3
0.01
V
1
1.2
µA
V
NOTE 3: Power good is not valid for the first 100 µs after EN goes high. Please refer to the application section for more information.
oscillator
PARAMETER
fs
f(SYNC)
Oscillator frequency
VIH
VIL
SYNC high level input voltage
Synchronization range
CMOS-logic clock signal on SYNC pin
MIN
TYP
MAX
UNIT
500
750
1000
kHz
1000
kHz
500
1.3
V
SYNC low level input voltage
Ilkg
SYNC input leakage current
Duty cycle of external clock signal
8
TEST CONDITIONS
SYNC = GND or VIN
0.01
20%
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
0.4
V
0.1
µA
60%
SGLS243A − APRIL 2004 − REVISED JUNE 2008
electrical characteristics over recommended operating free-air temperature range, VI = 3.6 V,
VO = 2.5 V, IO = 300 mA, EN = VIN, ILIM = VIN, TJ = −40°C to 125°C (unless otherwise noted) (continued)
output
PARAMETER
VO
Vref
VO
Adjustable output voltage range
TPS62000
Reference voltage
TPS6200x
Fixed output voltage (see Note 4)
Line regulation
Load regulation
η
TEST CONDITIONS
Efficiency
Start-up time
MIN
TYP
MAX
0.8
5.5
0.45
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62001
0.9 V
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62002
1V
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62003
1.2 V
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62004
1.5 V
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62005
1.8 V
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62008
1.9 V
VI = 2.5 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62006
2.5 V
VI = 2.7 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
TPS62007
3.3 V
VI = 3.6 V to 5.5 V; 0 mA ≤ IO ≤ 600 mA
10 mA < IO ≤ 600 mA
−4%
4%
−4%
3%
0.05
VI = 5.5 V; IO = 10 mA to 600 mA
VI = 5 V; VO = 3.3 V; IO = 300 mA
VI = 3.6 V; VO = 2.5 V; IO = 200 mA
IO = 0 mA, time from active EN to VO
V
V
TPS62000
adjustable
VI = VO + 0.5 V (min. 2 V) to 5.5 V,
IO = 10 mA
UNIT
V
%/V
0.6%
95%
0.4
2
ms
NOTE 4: The output voltage accuracy includes line and load regulation over the full temperature range, TJ = −40°C to 125°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SGLS243A − APRIL 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
η
Efficiency
vs Load current
3, 4, 5
V(drop)
Dropout voltage
vs Load current
6
vs Input voltage (power save mode)
7
vs Input voltage (forced PWM)
8
vs Free-air temperature
9
IQ
Operating quiescent current
fosc
Oscillator frequency
Load transient response
VO
10
Line transient response
11
Power save mode operation
12
Start-up
vs Time
13
Output voltage
vs Load current
14
EFFICIENCY
vs
LOAD CURRENT
100
EFFICIENCY
vs
LOAD CURRENT
100
VO = 3.3 V
90
VO = 2.5 V
90
80
70
Efficiency − %
Efficiency − %
VI = 3.6 V
VI = 5 V
80
70
VI = 5 V
60
60
50
50
40
0.1
1
10
100
IO − Load Current − mA
1000
40
0.1
Figure 3
10
VI = 3.6 V
1
10
100
IO − Load Current − mA
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1000
SGLS243A − APRIL 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
EFFICIENCY
vs
LOAD CURRENT
DROPOUT VOLTAGE
vs
LOAD CURRENT
300
100
VO = 1.8 V
250
Dropout Voltage − mV
Efficiency − %
90
80
VI = 3.6 V
70
VI = 5 V
60
50
200
VO = 2.5 V
150
VO = 3.3 V
100
50
40
0.1
0
1
10
100
IO − Load Current − mA
1000
0
100
200
300
400
IO − Load Current − mA
Figure 5
OPERATING QUIESCENT CURRENT
vs
INPUT VOLTAGE (FORCED PWM)
4000
Power-Save Mode,
SYNC = Low
I (Q)− Operating Quescent Current − µ A
I (Q)− Operating Quescent Current − µ A
60
55
TA = 80°C
TA = 20°C
45
TA =−40°C
40
35
30
2
2.5
3
3.5
600
Figure 6
OPERATING QUIESCENT CURRENT
vs
INPUT VOLTAGE (POWER SAVE MODE)
50
500
4
4.5
5
5.5
VI − Input Voltage (Power Save Mode) − V
Forced PWM,
SYNC = High
3500
TA = 80°C
TA = 20°C
3000
2500
TA =−40°C
2000
1500
1000
2
2.5
3
3.5
4
4.5
5
VI − Input Voltage (Forced PWM) − V
Figure 7
5.5
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SGLS243A − APRIL 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
OSCILLATOR FREQUENCY
vs
FREE-AIR TEMPERATURE
LOAD TRANSIENT RESPONSE
I(Load) = 60 mA to
540 mA,
VI = 3.6 V,
VO = 2.5 V
f − Oscillator Frequency − kHz
790
770
750
VO
25 mV/div
VI = 5 V
VI = 3.6 V
730
710
VI = 2 V
690
IO
500 mA/div
670
650
−40
−20
0
20
40
60
TA − Free-Air Temperature − °C
80
200 µs/div
Figure 9
Figure 10
LINE TRANSIENT RESPONSE
POWER SAVE MODE OPERATION
VL
2 V/div
VI
3.6 V to
4.6 V
VO
100 mV/div
IL
200 mA/div
400 µs/div
10 µs/div
Figure 11
12
Figure 12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SGLS243A − APRIL 2004 − REVISED JUNE 2008
TYPICAL CHARACTERISTICS
START-UP
vs
TIME
EN
2 V/div
VO
1 V/div
Power Good
1 V/div
II
200 mA/div
250 µs/div
Figure 13
OUTPUT VOLTAGE
vs
LOAD CURRENT
2.55
2.54
VO − Output Voltage − V
2.53
2.52
2.51
2.50
2.49
2.48
2.47
2.46
2.45
0
100
200
300
400
500
600
IO − Load Current − mA
Figure 14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SGLS243A − APRIL 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
adjustable output voltage version
When the adjustable output voltage version (TPS62000) is used, the output voltage is set by the external resistor
divider (see Figure 15).
The output voltage is calculated as:
V
O
+ 0.45 V
ǒ1 ) R1
Ǔ
R2
With R1 + R2 ≤ 1 MΩ
R1 + R2 should not be greater than 1 MΩ because of stability reasons.
For stability reasons, a small bypass capacitor (Cff) is required in parallel to the upper feedback resistor, see
Figure 15. The bypass capacitor value can be calculated as:
C (ff) +
1
for C o t 47 µF
2π x 30000 x R1
C (ff) +
1
for C o ≥ 47 µF
2π x 5000 x R1
R1 is the upper resistor of the voltage divider. For C(ff), choose a value which comes closest to the computed
result.
VI = 2.7 V to 5.5 V
1
VIN
L
9
L1 = 10 µH
VO = 2.5 V/600 mA
R3 = 320 kΩ
+
Ci = 10 µF
8
FB
EN
5
R1 = 820 kΩ
TPS62000
6
C(ff) =
6.8 pF
4
ILIM
PG
+
PG
Co = 10 µF
7
SYNC
GND
3
10
R2 = 180 kΩ
PGND
FC
2
C3 = 0.1 µF
Figure 15. Typical Application Circuit for Adjustable Output Voltage Option
inductor selection
A 10 µH minimum output inductor is used with the TPS6200x. Values larger than 22 µH or smaller than 10 µH
may cause stability problems because of the internal compensation of the regulator.
For output voltages greater than 1.8 V, a 22-µH inductance might be used in order to improve the efficiency of
the converter.
After choosing the inductor value of typically 10 µH, two additional inductor parameters should be considered:
first the current rating of the inductor and second the dc resistance.
The dc resistance of the inductance influences directly the efficiency of the converter. Therefore, an inductor
with the lowest dc resistance should be selected for the highest efficiency.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SGLS243A − APRIL 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
inductor selection (continued)
In order to avoid saturation of the inductor, the inductor should be rated at least for the maximum output current
plus the inductor ripple current which is calculated as:
DI L + V
O
V
1– O
V
I
L ƒ
I L(max) + I O(max) )
DI L
2
Where:
ƒ = Switching frequency (750 kHz typical)
L = Inductor value
∆IL = Peak-to-peak inductor ripple current
IL(max) = Maximum inductor current
The highest inductor current occurs at maximum VI.
A more conservative approach is to select the inductor current rating just for the maximum switch current of the
TPS6200x which is 1.6 A with ILIM = VIN and 900 mA with ILIM = GND. See Table 1 for recommended inductors.
Table 1. Tested Inductors
OUTPUT CURRENT
INDUCTOR VALUE
10 µH
0 mA to 600 mA
10 µH
0 mA to 300 mA
COMPONENT SUPPLIER
COMMENTS
Coilcraft DO3316P-103
Coilcraft DT3316P-103
Sumida CDR63B-100
Sumida CDRH5D28-100
High efficiency
Coilcraft DO1608C-103
Sumida CDRH4D28-100
Smallest solution
Coilcraft DS1608C-103
High efficiency
muRata LQH4C100K04
Smallest solution
output capacitor selection
For best performance, a low ESR output capacitor is needed. At output voltages greater than 1.8 V, ceramic
output capacitors can be used to show the best performance. Output voltages below 1.8 V require a larger
output capacitor and ESR value to improve the performance and stability of the converter.
Table 2. Capacitor Selection
OUTPUT VOLTAGE RANGE
OUTPUT CAPACITOR
OUTPUT CAPACITOR ESR
1.8 V ≤ VI ≤ 5.5 V
Co ≥ 10 µF
ESR ≤ 120 mΩ
0.8 V ≤ VI < 1.8 V
Co ≥ 47 µF
ESR > 50 mΩ
See Table 3 for recommended capacitors.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
SGLS243A − APRIL 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
output capacitor selection (continued)
If an output capacitor is selected with an ESR value ≤ 120 mΩ, its RMS ripple current rating always meets the
application requirements. The RMS ripple current is calculated as:
V
1– O
V
I
L ƒ
I RMS(C ) + V
O
o
1
2
Ǹ3
The overall output ripple voltage is the sum of the voltage spike caused by the output capacitor ESR plus the
voltage ripple caused by charge and discharging the output capacitor:
DV
O
+V
O
V
1– O
V
I
L ƒ
ǒ
8
1
Co
ƒ
Ǔ
) ESR
Where the highest output voltage ripple occurs at the highest input voltage VI.
Table 3. Tested Capacitors
CAPACITOR VALUE
ESR/mΩ
10 µF
50
Taiyo Yuden
JMK316BJ106KL
COMPONENT SUPPLIER
Ceramic
COMMENTS
47 µF
100
Sanyo 6TPA47M
POSCAP
68 µF
100
Spraque
594D686X0010C2T
Tantalum
input capacitor selection
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes.
The input capacitor should have a minimum value of 10 µF and can be increased without any limit for better input
voltage filtering.
The input capacitor should be rated for the maximum input ripple current calculated as:
I RMS + I
Ǹ ǒ Ǔ
V
O(max)
O
V
I
V
1– O
V
I
IO
The worst case RMS ripple current occurs at D = 0.5 and is calculated as: I RMS +
.
2
Ceramic capacitors show a good performance because of their low ESR value and they are less sensitive
against voltage transients compared to tantalum capacitors.
Place the input capacitor as close as possible to the input pin of the IC for best performance.
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SGLS243A − APRIL 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
layout considerations
As for all switching power supplies, the layout is an important step in the design, especially at high peak currents
and switching frequencies. If the layout is not carefully done, the regulator might show stability problems as well
as EMI problems.
Therefore, use wide and short traces for the main current paths as indicted in bold in Figure 16. The input
capacitor should be placed as close as possible to the IC pins, as well as the inductor and output capacitor. Place
the bypass capacitor, C3, as close as possible to the FC pin. The analog ground, GND, and the power ground,
PGND, need to be separated. Use a common-ground node, as shown in Figure 16, to minimize the effects of
ground noise.
1
VI
VIN
L
EN
FB
L1
9
VO
+
8
Ci
R3
5
R1
TPS62000
6
C(ff)
4
ILIM
PG
+
PG
Co
7
R2
10
SYNC
GND
PGND
FC
3
C3
2
Figure 16. Layout Diagram
typical application
VI = 5 V
C1
10 µF
1
8
VIN
L
EN
FB
9
7
ILIM
SYNC
GND
3
VO = 3.3 V/600 mA
5
TPS62007
6
L1
22 µH
680 kΩ
PGND
PG
FC
C2
10 µF
10
4
Power
Good
2
L1:
Sumdia CDRH5D28-220
C1, C2: 10-µF Ceramic Taiyo Yuden
JMK316BJ106KL
C3:
0.1-µF Ceramic
C3
0.1 µF
Figure 17. Standard 5 V to 3.3 V/600 mA Conversion − High Efficiency
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
SGLS243A − APRIL 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
typical application (continued)
1
VI = 2.7 V to 4.2 V
C1
10 µF
8
VIN
L
EN
FB
9
7
ILIM
470 kΩ
PGND
SYNC
GND
3
VO = 2.5 V/600 mA
5
TPS62006
6
L1
10 µH
PG
FC
C2
10 µF
10
4
Power Good
L1:
C1,C2:
2
C3
0.1 µF
C3:
Sumdia CDRH5D28-100
10-µF Ceramic Taiyo Yuden
JMK316BJ106KL
0.1-µF Ceramic
Figure 18. Single Li-on to 2.5 V/600 mA Using Ceramic Capacitors Only
VI = 2.5 V to 4.2 V
C1
10 µF
1
8
VIN
L
EN
FB
9
7
ILIM
PGND
SYNC
GND
3
PG
FC
VO = 1.8 V/300 mA
5
C2
10 µF
TPS62005
6
L1
10 µH
10
4
L1:
C1,C2:
2
C3
0.1 µF
C3:
Murata LQH4C100K04
10-µF Ceramic Taiyo Yuden
JMK316BJ106KL
0.1-µF Ceramic
NOTE: For low noise operation, connect SYNC to VIN.
Figure 19. Single Li-on to 1.8 V/300 mA − Smallest Solution Size
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SGLS243A − APRIL 2004 − REVISED JUNE 2008
APPLICATION INFORMATION
typical application (continued)
1
VI = 2 V to 3.8 V
C1
10 µF
8
VIN
L
EN
FB
L1
10 µH
9
VO = 1.2 V/200 mA
5
C2
47 µF
TPS62003
6
7
ILIM
10
PGND
SYNC
GND
4
PG
FC
3
+
L1:
C1:
2
C3
0.1 µF
C2:
C3:
Murata LQH4C100K04
10-µF Ceramic Taiyo Yuden
JMK316BJ106KL
Sanyo 6TPA47M
0.1-µF Ceramic
Figure 20. Dual Cell NiMH or NiCd to 1.2 V/200 mA − Smallest Solution Size
VI = 2.5 V to 5.5 V
C1
10 µF
1
8
VIN
L
EN
FB
9
L1
10 µH
R4
5 820 kΩ
VO = 1.1 V or
1.5 V/600 mA
R1
470 kΩ
TPS62000
6
7
ILIM
SYNC
GND
3
PG
PGND
FC
4
PG†
C(ff)ĕ
150 pF
C2
47 µF
+
10
R2
326 kΩ
R3
524 kΩ
2
C3
0.1 µF
L1:
C1:
Sumida CDRH5D28-100
Q1
10-µF Ceramic Taiyo Yuden
BSS138
JMK316BJ106KL
C2:
Sanyo 6TPA47M
C3:
0.1-µF Ceramic
† Use a small R-C filter to filter wrong reset signals during output voltage transitions.
‡ A large value is used for C(ff) to compensate for the parasitic capacitance introduced into the regulation loop by Q1.
Logic Input
Hi
VO = 1.5 V
Low VO = 1.1 V
Figure 21. Dynamic Output Voltage Programming As Used in Low Power DSP Applications
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
ACTIVE
MSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS62004QDGSRQ1
ACTIVE
MSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS62005QDGSRQ1
ACTIVE
MSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS62006QDGSRQ1
ACTIVE
MSOP
DGS
10
TPS62007QDGSRQ1
ACTIVE
MSOP
DGS
10
2500
Green (RoHS
& no Sb/Br)
Call TI
Samples
(Requires Login)
TPS62000QDGSRQ1
TBD
(3)
Call TI
CU NIPDAU Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Aug-2012
OTHER QUALIFIED VERSIONS OF TPS62000-Q1, TPS62004-Q1, TPS62005-Q1, TPS62006-Q1, TPS62007-Q1 :
• Catalog: TPS62000, TPS62004, TPS62005, TPS62006, TPS62007
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated