NSC LM9627CCEA

LM9627 Color CMOS Image Sensor VGA 30 FPS
General Description
Applications
The LM9627 is a high performance, low power, third inch VGA
CMOS Active Pixel Sensor capable of capturing color digital still
or motion images and converting them to a digital data stream.
•
•
•
•
•
•
In addition to the active pixel array, an on-chip 12 bit A/D convertor, fixed pattern noise elimination circuits and a video gain
amplifier is provided. Furthermore, an integrated programmable
smart timing and control circuit allows the user maximum flexibility in adjusting integration time, active window size, gain and
frame rate. Various control, timing and power modes are also
provided.
PC Camera
Digital Still Camera
Video Conferencing
Security Cameras
Toys
Machine Vision
Key Specifications
Total: 664H x 504V
Active: 648H x 488V
• Array Format
• Effective Image Area
Features
• Optical Format
•
•
•
•
•
•
•
•
•
•
• Pixel Size
Supplied with micro lenses
Video or snapshot operations
Programmable pixel clock, inter-frame and inter-line delays.
Programmable partial or full frame integration
Programmable gain adjustment
Horizontal & vertical sub-sampling (2:1 & 4:2)
Windowing
External snapshot trigger & event synchronisation signals
Auto black level compensation
Flexible digital video read-out supporting programmable:
- polarity for synchronisation and pixel clock signals
- leading edge adjustment for horizontal synchronization
• Programmable via 2 wire I2C compatible serial interface
• Power on reset & power down mode
Total: 4.98mm x 3.78 mm
Active: 4.86 mm x 3.66 mm
1/3“
7.5µm x 7.5µm
• Video Outputs
8,10 & 12 Bit Digital
• Dynamic Range
57dB
• FPN
0.35%
• Sensitivity
red
green
blue
14.5 kLSBs/lux.s
7.5 kLSBs/lux.s
5.1 kLSBs/lux.s
• Quantum Efficiency
27%
• Fill Factor
47% (no micro lens)
• Color Mosaic
Bayer pattern
• Package
48 LCC
• Single Supply
3.3 V
• Power Consumption
90 mW
0 to 50o C
• Operating Temp
System Block Diagram
Storage
lens
LM9627
12bit digital image
Digital Image
Processor
I2 C compatible
event trigger
snapshot
2000 National Semiconductor Corporation
Confidential
www.national.com
LM9627 Color CMOS Image Sensor VGA 30 FPS
March 2001
Digital Video
Framer
12 Bit A/D
AMP
Black Level
Compensation
APS Array
Bad Pixel
Detect & Correct
Horizontal Shift
Register
Column CDS
Row Address
Decoder
d[11:0]
pclk
hsync
vsync
POR
Reset
Gen
Vertical
Timing
Row Address
Gen
Horizontal
Timing
Gain
Control
Register Bank
Clock Gen
Controller
(sequencer)
Power
Control
Master Timer
mclk
I2C Compatible
Serial I/F
sda
sclk
sadr
snapshot irq
pdwn
Figure 1. Chip Block Diagram
extsync
vrl
vsrvdd
extsync
6
5
4
3
2
1
48 47 46 45 44 43
NC
vdd_pix
vdd_od3
irq
vss_od3
sadr
vss_od1
sda
vdd_od1
Connection Diagram
sclk
7
42
NC
snapshot
8
41
fine_i
resetb
9
40
gnd
pdwn
10
39
fine_ctrl
38
offset
37
vdd_ana1
vss_ana1
vss_dig
11
vdd_dig
12
hsync
13
36
vsync
14
35
vref_adc
LM9627
48 PIN LCC
31
19 20 21 22 23 24 25 26 27 28 29 30
NC
18
d11
vss_od2
vdd_od2
d10
32
d9
17
d8
d0
d7
vdd_ana2
d6
33
d5
16
d4
mclk
d3
34
d2
15
d1
pclk
vss_ana2
NC
LM9627
Overall Chip Block Diagram
Ordering Information
Temperature
(0°C ≤ TA ≤ +50°C)
LM9627 CCEA
Confidential
NS Package
LCC
2
www.national.com
LM9627
Typical Application Circuit
37 vdd_ana1
0.1µF
7
5
6
sadr
48
sda
irq
8
Serial Control Bus
sclk
4
snapshot
3.3V analog
10
resetb
mclk
9
pdwn
16
Camera Control
extsync
System Control
3.3V analog
vdd_ana2 33
36 vss_ana1
vss_ana2 34
47 vdd_od1
vdd_od2 31
46 vss_od1
vss_od2 32
44 vdd_od3
vdd_dig
45 vss_od3
vss_dig 11
3.3V digital
0.1µF
3.3V digital
0.1µF
3.3V analog
0.1µF
0.1µF
3.3V digital
0.1µF
3.3Vdigital
3 vdd_pix
LM9627
12
0.1µF
vsrvdd 1
1.0µF
2 vrl
3.3V analog
vdd_ana
1.5kΩ
35
820Ω
vref_adc
2 2 kΩ
1%
fine_i 41
fine_ctrl 39
0.1µF
1N4148
2N3904
1 0 kΩ
1%
NC
NC
NC
NC
1 . 2 kΩ
1%
offset 38
470Ω
1%
13 14 15
d0
d1
d2
d3
d4
d5
d6
d7
d8
d9
d10
d11
gnd 40
pclk
vsync
4.7µF
hsync
18
19
42
43
vdd_ana
30 29 28 27 26 25 24 23 22 21 20 17
Digital Video Bus
Figure 2. Typical Application Diagram
Scan Read Out Direction
pin 1
vertical scan
(0,0)
(0,0)
digital
out
(0,0)
horizontal scan
lens
CMOS Image Sensor
Figure 3. Scan directions and position of origin in imaging system
Confidential
3
www.national.com
LM9627
Pin Descriptions
Pin
Name
I/O
Typ
Description
1
vsrvdd
I0
P
Analog bidirectional, it should be connect to ground via a 1.0µf capacitor. This pin is the
internal charge pump voltage source.
2
vrl
I
A
Anti blooming pin. This pin is normally tied to ground.
3
vdd_pix
I
P
3.3 volt supply for the pixel array.
4
irq
O
D
Digital output, the interrupt request pin. This pin generates interrupts during snapshot
mode.
5
sadr
I
D
Digital input with pull down resistor. This pin is used to program different slave addresses
for the sensor in an I2 C compatible system.
6
sda
IO
D
I2 C compatible serial interface data bus. The output stage of this pin has an open drain
driver.
7
sclk
I
D
I2 C compatible serial interface clock.
8
snapshot
I
D
Digital input with pull down resistor used to activate (trigger) a snapshot sequence.
9
resetb
I
D
Digital input with pull up resistor. When forced to a logic 0 the sensor is reset to its default
power up state. The resetb signal is internally synchronized to mclk which must be running for a reset to occur.
10
pdwn
I
D
Digital input with pull down resistor. When forced to a logic 1 the sensor is put into power
down mode.
11
vss_dig
I
P
0 volt power supply for the digital circuits.
12
vdd_dig
I
P
3.3 volt power supply for the digital circuits.
D
Digital Bidirectional. This is a dual mode pin. When the sensor’s digital video port is configured to be a master, (the default), this pin is an output and is the horizontal synchronization pulse. When the sensor’s digital video port is configured to be a slave, this pin is
an input and is the row trigger.
13
hsync
IO
14
vsync
IO
D
Digital Bidirectional. This is a dual mode pin. When the sensor’s digital video port is configured to be a master, (the default), this pin is an output and is the vertical synchronization pulse. When the sensor’s digital video port is configured to be a slave, this pin is an
input and is the frame trigger.
15
pclk
O
D
Digital output. The pixel clock.
16
mclk
I
D
Digital input. The sensor’s master clock input.
17
d0
O
D
Digital output. Bit 0 of the digital video output bus. This output can be put into tri-state
mode.
18
NC
Pin not used, do not connect.
19
NC
Pin not used, do not connect.
20
d1
O
D
Digital output. Bit 1 of the digital video output bus. This output can be put into tri-state
mode.
21
d2
O
D
Digital output. Bit 2 of the digital video output bus. This output can be put into tri-state
mode.
22
d3
O
D
Digital output. Bit 3 of the digital video output bus. This output can be put into tri-state
mode.
23
d4
O
D
Digital output. Bit 4 of the digital video output bus. This output can be put into tri-state
mode.
24
d5
O
D
Digital output. Bit 5 of the digital video output bus. This output can be put into tri-state
mode.
25
d6
O
D
Digital output. Bit 6 of the digital video output bus. This output can be put into tri-state
mode.
Confidential
4
www.national.com
LM9627
Pin Descriptions (Continued)
Pin
Name
I/O
Typ
Description
26
d7
O
D
Digital output. Bit 7 of the digital video output bus. This output can be put into tri-state
mode.
27
d8
O
D
Digital output. Bit 8 of the digital video output bus. This output can be put into tri-state
mode.
28
d9
O
D
Digital output. Bit 9 of the digital video output bus. This output can be put into tri-state
mode.
29
d10
O
D
Digital output. Bit 10 of the digital video output bus. This output can be put into tri-state
mode.
30
d11
O
D
Digital output. Bit 11 of the digital video output bus. This output can be put into tri-state
mode.
31
vdd_od2
I
P
3.3 volt supply for the digital IO buffers.
32
vss_od2
I
P
0 volt supply for the digital IO buffers
33
vdd_ana2
I
P
3.3 volt supply for analog circuits.
34
vss_ana2
I
P
0 volt supply for analog circuits.
35
vref_adc
I
A
A/D reference resistor ladder voltage. See figure 4 for equivalent circuit.
36
vss_ana1
I
P
0 volt supply for analog circuits.
37
vdd_ana1
I
P
3.3 volt supply for analog circuits.
38
offset
I
A
Analog input used to adjust the offset of the sensor. See figure 4 for equivalent circuit.
39
fine_ctrl
O
A
Analog output used to drive the offset pin.
40
gnd
41
fine_i
42
NC
Pin not used, do not connect.
43
NC
Pin not used, do not connect.
44
vdd_od3
I
P
3.3 volt supply for the sensor.
45
vss_od3
I
P
0 volt supply for the sensor.
46
vss_od1
I
P
0 volt supply for the digital IO buffers
47
vdd_od1
I
P
3.3 volt supply for the digital IO buffers.
48
extsync
O
D
Digital output. The external event synchronization signal is used to synchronize external
events in snapshot mode.
This pin must be tied to ground.
I
A
Bias current for the fine offset adjust.
Legend: (I=Input), (O=Output), (IO=Bi-directional), (P=Power), (D=Digital), (A=Analog).
adc_vref
offset
800Ω
1KΩ
200Ω
Figure 4. Equivalent Circuits For adc_ref and offset pins
Confidential
5
www.national.com
LM9627
Absolute Maximum Ratings (Notes 1 & 2)
Operating Ratings
Any Positive Supply Voltage
6.5V
Voltage On Any Input or Output Pin
-0.5V to 6.5V
Input Current at any pin (Note 3)
±25mA
ESD Susceptibility (Note 5)
Human Body Model
2000V
Machine Model
200V
Package Input Current (Note 3)
±50mA
Package Power Dissipation @ TA (Note 4)
2.5W
Soldering Temperature Infrared,
10 seconds (Note 6)
220°C
Storage Temperature
-40°C to 125°C
Operating Temperature Range
All VDD Supply Voltages
Voltage Range on vref_adc pin
Voltage Range on offset pin
(Notes 1 & 2)
0°C≤T≤+50°C
+3.15V to +3.6V
+0.6V to +1.0V
+0.04V to +0.4V
DC and logic level specifications
The following specifications apply for all VDD pins= +3.3V. Boldface limits apply for TA = TMIN to TMAX : all other limits TA = 25o C
(Note 7)
Symbol
Parameter
Conditions
Min
note 9
Typical
note 8
Max
note 9
Units
sclk, sda, sadr, Digital Input/Output Characteristics
VIH
Logical “1” Input Voltage
0.7* vdd_od
vdd_od+0.5
V
VIL
Logical “0” Input Voltage
-0.5
0.3* vdd_od
V
VOL
Logical “0” Output Voltage
vdd_od = +3.15V, Iout=3.0mA
0.5
V
Vhys
Hysteresis (SCLK pin only)
vdd_od = +3.15V
Ileak
Input Leakage Current
Vin=vss_od
0.05*vdd_o
d
V
-1
mA
mclk, snapshot, pdwn, resetb, hsync, vsync Digital Input Characteristics
VIH
Logical “1” Input Voltage
vdd_dig = +3.6V
2.0
V
VIL
Logical “0” Input Voltage
vdd_dig = +3.15V
IIH
Logical “1” Input Current
VIH = vdd_dig
0.1
mA
IIL
Logical “0” Input Current
VIL = vss_dig
-1
mA
0.8
V
d0 - d11, pclk, hsync, vsync, extsync, irq, Digital Output Characteristics
VOH
Logical “1” Output Voltage
vdd_od=3.15V, Iout=-1.6mA
VOL
Logical “0” Output Voltage
vdd_od=3.15V, Iout =-1.6mA
IOZ
TRI-STATE Output Current
VOUT = vss_od
VOUT = vdd_od
IOS
Output Short Circuit Current
2.2
V
0.5
V
-0.1
0.1
mA
mA
+/-17
mA
Power Supply Characteristics
IA
Analog Supply Current
Power down mode, no clock.
Operational mode in dark
700
19
mA
mA
ID
Digital Supply Current
Power down mode, no clock.
Operational mode in dark
300
7
mA
mA
Power Dissipation Specifications
The following specifications apply for All VDD pins = +3.3V. Boldface limits apply for TA = T MIN to TMAX : all other limits TA = 25 o C.
Symbol
Parameter
Conditions
Min
note 9
Typical
note 8
Max
note 9
Units
Pdwn
Power Down
no clock running
5
mW
PWR
Average Power Dissipation
mclk = 48Mhz & sensors default settings in dark.
90
mW
Confidential
6
www.national.com
The following specifications apply for all VDD pins= +3.3V. Boldface limits apply for TA = TMIN to TMAX : all other limits TA = 25oC.
Symbol
Parameter
Min
note 9
Conditions
Video Amplifier Nominal Gain
64 linear steps
Typical
note 8
Max
note 9
Units
0-15
dB
AC Electrical Characteristics
The following specifications apply for All VDD pins = +3.3V. Boldface limits apply for T A = TMIN to T MAX: all other limits TA = 25 o C.
Symbol
Fmclk
Parameter
Conditions
Input Clock Frequency
Min
note 9
Max
note 9
Units
12
48
MHz
Tch
Clock High Time
@ CLKmax
10
45
ns
Tcl
Clock Low Time
@ CLKmax
10
45
ns
Clock Duty Cycle
@ CLKmax
45/55
55/45
min/max
Trc , Tfc
Clock Input Rise and Fall Time
3
Fhclk
Internal System Clock Frequency
1.0
Treset
Reset pulse width
1.0
FRM rate
Note 1:
Note 2:
Note 3:
Note 4:
Typical
note 8
Frame Rate
ns
14.0
MHz
µs
1
30
fps
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications
and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions
listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions.
All voltages are measured with respect to VSS = vss_ana = vss_od = vss_dig = 0V, unless otherwise specified.
When the voltage at any pin exceeds the power supplies (VIN < VSS or VIN > VDD), the current at that pin should be limited to 25mA. The 50mA maximum package input current rating limits the number of pins that can safely exceed the power
supplies with an input current of 25mA.
The absolute maximum junction temperature (TJmax) for this device is 125 o C. The maximum allowable power dissipation
is dictated by TJmax, the junction-to-ambient thermal resistance (ΘJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax - TA)/ΘJA. In the 48-pin LCC, ΘJA is 38.5 o C/W, so PDMAX = 2.5W at 25o C
Note 5:
Note 6:
Note 7:
and 1.94W at the maximum operating ambient temperature of 50oC. Note that the power dissipation of this device under
normal operation will be well under the PDMAX of the package.
Human body model is 100pF capacitor discharged through a 1.5kΩ resistor. Machine model is 220pF discharged through
ZERO Ohms.
See AN450, “Surface Mounting Methods and Their Effect on Product Reliability”, or the section entitled “Surface Mount”
found in any post 1986 National Semiconductor Linear Data Book, for other methods of soldering surface mount devices.
The analog inputs are protected as shown below. Input voltage magnitude up to 500mV beyond the supply rails will not
damage this device. However, input errors will be generated If the input goes above AV+ and below AGND.
VDD
Pad
Internal Circuits
IOP
VSS
Note 8:
Note 9:
Typical figures are at TJ = 25o C, and represent most likely parametric norms.
Test limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Confidential
7
www.national.com
LM9627
Video Amplifier Specifications
LM9627
CMOS Active Pixel Array Specifications
Parameter
Value
Number of pixels (column, row)
Total
Active
664 x 504
648 x 488
Array size (x,y Dimensions)
Total
Active
Units
pixels
pixels
4.98 x 3.78
4.86 x 3.66
mm
mm
Pixel Pitch
7.5
µ
Fill Factor (without micro-lens)
47
%
Image Sensor Specifications
The following specifications apply for All VDD pins = +3.3V, TA = 25o C, Illumination Color Temperature = 2850 o K, IR cutoff filter at
700nm, mclk = 48MHz, frame rate = 30Hz, vref_adc = 0.6 volt, video gain 0dB.
Parameter
Min
Conditions
Optical Sensitivity @ A/D output
red
green
blue
Typical
note 1
14.5
7.5
5.1
Optical Sensitivity @ A/D input
red
green
blue
Max
Units
kLSBs/(lux.s)
2.12
1.1
0.75
volt/(lux.s)
Dynamic Range
57
dB
Read Noise
5.3
LSBs
Offset Fixed Pattern Noise
RMS value of pixel FPN in dark
as a percentage of full scale.
0.35
%
Sensitivity Fixed Pattern Noise
RMS variation of pixel sensitivities as a percentage of the average sensitivity.
1
%
Note 1:
Typical figures are at TJ = 25o C, and represent most likely parametric norms.
Confidential
8
www.national.com
LM9627
Sensor Response Curves
8.00E+02
red
Spectral sensitivity [V/((W/m^2)*s)]
7.00E+02
6.00E+02
green
5.00E+02
blue
4.00E+02
3.00E+02
2.00E+02
1.00E+02
0.00E+00
370
420
470
520
570
620
670
720
770
820
wavelength [nm]
5000
4000
ADC output code [LSBs]
A/D output code
Figure 5. Spectral Response Curve
3000
green
blue
2000
red
1000
0
0
0.1
0.2
0.3
0.4
0.5
0.6
Exposure [lux.s]
Figure 6. Linearity Response Curve
Confidential
9
www.national.com
1.0
OVERVIEW
0-15dB
1.1
Light Capture and Conversion
The LM9627 contains a CMOS active pixel array consisting of
648 rows by 488 columns. This active region is surrounded by 8
columns and 8 rows of optically shielded (black) pixels as shown
in Figure7.
648 columns, 488 rows
color (Bayer pattern) active pixels
Video
AMP
12 Bit A/D
Analog pixel values
8 columns, 8 rows
black pixels
Digital pixel data
Figure 9: Analog Signals Conditioning & Conversion to
Digital
do[11:0]
Digital Video
Framer
8 columns, 8 rows
black pixels
Black Level
Compensation
Bad Pixel
Correction
The digital pixel data is further processed to:
• remove defects due to bad pixels,
• compensate black level, before being framed and presented
on the digital output port. (see Figure 10).
pclk
hsync
vsync
Figure 10. Digital Pixel Processing.
Figure 7: CMOS APS region of the LM9627
The color filters are Bayer pattern coded starting at row 8 and
column 8. (rows 0 to 7 & columns 0 to 7 are black). The color
coding is green, red, green, red until the end of row 8, then blue,
green, blue, green until the end or row 9 and so on (see Figure
7).
1.2
Program and Control Interfaces
The programming, control and status monitoring of the LM9627
is achieved through a two wire I2 C compatible serial bus. In
addition, a slave address pin is provided (see Figure 11).
At the beginning of a given integration time the on-board timing
and control circuit will reset every pixel in the array one row at a
time as shown in Figure 8. Note that all pixels in the same row
are simultaneously reset, but not all pixels in the array.
a b c
Line Address
LM9627
Functional Description
d e f
g h
i
j
k
sda
Register Bank
I2C Compatible
Serial I/F
sclk
l m n o p q r
sadr
0
1
2
3
4
5
6
7
8
9
10
11
Figure 11. Control Interface to the LM9627.
Additional control and status pins: snapshot and external event
synchronization are provided allowing the latency of the serial
control port to be bypassed during single frame capture. An
interrupt request pin is also available allowing complex snapshot
operations to be controlled via an external micro-processor (see
Figure 12).
12
13
14
15
Analog Data Out
CDS/Shift Register
irq
Timing
Generator
Figure 8: CMOS APS Row and Column addressing scheme
At the end of the integration time, the timing and control circuit
will address each row and simultaneously transfer the integrated
value of the pixel to a correlated double sampling circuit and
then to a shift register as shown in Figure 8.
extsyn
snapshot
Figure 12. Snapshot & External Event Trigger Signals
Once the correlated double sampled data has been loaded into
the shift register, the timing and control circuit will shift them out
one pixel at a time starting with column “a”.
The pixel data is then fed into an analog video amplifier, where a
user programmed gain is applied (see Figure 9).
After gain adjustment the analog value of each pixel is converted to a 12 bit digital data as shown in Figure 9.
Confidential
10
www.national.com
2.0
Column/Horizontal
a b c d e f g h i j k l mn o p q r
WINDOWING
The integrated timing and control circuit allows any size window
in any position within the active region of the array to be read out
with a 1x1 pixel resolution. The window read out is called the
“Display Window”.
Row/Vertical
A “Scan Window” must be defined first, by programing the start
and end row addresses as shown in Figure 13. Four coordinates
(start row address, start column address, end row address &
end column address) are programmed to define the size and
location of the “Display Window” to be read out (see Figure 13).
display col
display col
scan row
end address
start address
start address
display row
start address
display row
end address
Display Window
scan row
end address
Figure 14: Progressive Scan Read Out Mode
Scan Window
Active Pixel Array
Figure 13. Windowing
Notes:
• The “Display Window” must always be defined within the
“Scan Window”.
• A “Display Window” can only be read out in the progressive
scan mode.
• By default the “Display Window” is the complete array.
3.2
Interlaced Readout Mode
In interlaced readout mode, pixels are read out in two fields, an
Odd Field followed by an Even Field.
The Odd Field, consisting of all even row pairs contained within
the display window, is read out first. Each pixel in the “Odd Field”
is consecutively read out, one pixel at a time, starting with the
left most pixel in the top most row pair.
The Even Field, consisting of all odd row pairs contained within
the display window, is then read out. Each pixel in the “Even
Field” is consecutively read out, one pixel at a time, starting with
the left most pixel in the top most row pair.
2.1
Programming the scan window
Two registers (SROWS & SROWE) are provided to program the
size of the scan window. The start and end row address of the
scan window is given by:
Row/Vertical
Column/Horizontal
a b c d e f g h i j k l mn o p q r
scan row start address = (2* SwStartRow) + SwLsb
scan row end address = (2* SwEndRow) + 1 + SwLsb
Where:
SwStartRow
is the contents of the Scan Window start row
register (SROWS)
SwEndROW
is the contents of the Scan Window end row register (SROWE)
SwLsb
is bit 6 of the Display Window LSB register
(DWLSB)
READ OUT MODES
3.1
Progressive Scan Readout Mode
In progressive scan readout mode, every pixel in every row in
the display window is consecutively read out, one pixel at a time,
starting with the left most pixel in the top most row. Hence, for
the example shown in Figure 14, the read out order will be
a0,b0,...,r0 then a1,b1,...,r1 and so on until pixel r20 is read out.
Confidential
0
1
4
5
8
9
12
13
16
17
Row/Vertical
Odd Field
Column/Horizontal
a b c d e f g h i j k l mn o p q r
2.2
Programming the display window
Five register (DROWS, DROWE, DCOLS, DCOLE and DWLSB)
are provided to program the display window as described in the
register section of this datasheet.
3.0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2
3
6
7
10
11
14
15
18
19
Even Field
Figure 15: Interlace Read Out Mode
Hence, for the example shown in Figure 15, the display window
is broken up into two fields, as shown in Figure 15. Pixels
a0,b0,...,r0 and a1,b1,...,r1 are readout first and so on until pixels a17,b17,...r17 in the even field are read out. The even field
read out is followed by pixels in the odd field, a2,b2,...,r2 then
a3,b3,...,r3 until pixels a19,b19,...,r19
11
www.national.com
LM9627
Functional Description (continued)
4.0
SUBSAMPLING MODES
4.1
2:1 Sub-Sampling
The timing and control circuit can be programmed to sub-sample pixels in the display window vertically, horizontally or both,
with an aspect ratio of 2:1 as illustrated in Figure16.
4.2
4:2 Sub-Sampling
The timing and control circuit can be programmed to sub-sample pixels in the display window vertically, horizontally or both,
with an aspect ratio of 4:2 as illustrated in Figure17
Column/Horizontal
a b c d e f g h i j k l mn o p q r
0
1
0
1
2
3
4
5
6
7
8
9
Row/Vertical
Row/Vertical
Column/Horizontal
a b c d e f g h i j k l mn o p q r
2
3
4
5
6
7
8
9
a) Horizontal Sub-sampling
a) Horizontal Sub-Sampling
Column/Horizontal
a b c d e f g h i j k l mn o p q r
0
1
2
3
4
5
6
7
8
9
Row/Vertical
Row/Vertical
Column/Horizontal
a b c d e f g h i j k l mn o p q r
0
1
2
3
4
5
6
7
8
9
b) Vertical Sub-sampling
b) Vertical Sub-Sampling
Column/Horizontal
a b c d e f g h i j k l
Column/Horizontal
a b c d e f g h i j k l mn o p q r
l n o p q r
0
1
2
3
4
5
6
7
8
9
Row/Vertical
Row/Vertical
LM9627
Functional Description (continued)
0
1
2
3
4
5
6
7
8
9
c) Horizontal & Vertical Sub-sampling
c) Horizontal & Vertical Sub-Sampling
Green Pixel
Green Pixel
Red Pixel
Blue Pixel
Not Read Out
Red Pixel
Blue Pixel
Figure 17: Example 4:2 Sub-sampling
Not Read Out
Figure 16: Example of 2:1 Sub-sampling
Confidential
12
www.national.com
5.0
SNAPSHOT MODE
The LM9627 is capable of capturing a single frame of an image
under hardware or software control, with or without the aid of an
external shutter. Two registers, SNAPSHOTMODE0 &
SNAPSHOTMODE1, are provided to program, monitor and control all snapshot sequences.
5.1
Software Controlled Snapshots
The snapshot mode events can be software controlled by writing
to and reading from the snapshot mode registers over the I2C
compatible interface.
5.2
Hardware Controlled Snapshots
Two dedicated pins are provided on the LM9627, snapshot &
extsync, allowing the snapshot mode events to be controlled by
hardware. The snapshot pin must be enabled by writing to the
SnapEnable bit of the MCFG0 register.
5.3
Auto Snapshot Mode
In auto snapshot mode (see figure 20), upon the receipt of a
snapshot or FTriggerNow trigger signal, the integrated timing and
control circuit will set the FTriggerEN bit and generate an internal TRIGGER signal (see figure 19), thus resetting the array one
row at a time. At end of the reset cycle the timing and control circuit will signal the shutter to open via extsync pin or FtSync bit.
At the end of the programmed integration time the shutter will be
signalled to close, and the pixel read-out will commence as
shown in figure 18a. At the end of the read-out sequence the
FTriggerEN will be automatically reset and the sensor will return
to video capture mode as shown in figure 20.
If an external shutter is not available then at least two frames
need to be taken so that the pixels can be integrated over one
frame as shown in Figure 18b.
To use auto snapshot mode the SsEngage bit of the
SNAPSHOTMODE1 register must be set to zero.
Array reset,
programmable 1 to 4 frames
snapshot or FTriggerNow
Capture
Data
image read-out
note 1
note 2
irq
note 3
FTriggerEn
extsync or FtSync
FtBusy
Start Snapshot Sequence
Start of Array Reset Frames
Open Shutter
Close shutter & start read-out
Read-out complete
a) With External Shutter
Array reset,
Capture
Data
programmable 1 to 4 frames image read-out
snapshot or FTriggerNow
irq
note 1
note 2
note 3
FTriggerEn
extsync or FtSync
FtBusy
Start Snapshot sequence
Start of Array Reset Frames
Integration Start
Start Read-out
Bold external pins
italic register bits
Read-out Complete
b) Without External Shutter
Note 1:
Note 2:
Note 3:
This wave form shows the snapshot pin programmed to the default pulse mode.
The irq pulse is taken low when the snapshot trigger interrupt flag (SsTrigFlag) in the snapshot mode1 (SNAPMODE1) register is read.
The irq pulse is taken low when the snapshot trigger interrupt flag (SsRdFlag) in the snapshot mode1 (SNAPMODE1 ) register is read.
Figure 18. Snapshot Mode
Confidential
13
www.national.com
LM9627
Functional Description (continued)
snapshot
SnapShotPol
TRIGGER
VIDEO
SnapEnable
c: SsRdFlag && (SnapshotMod || (SnapshotMod && TRIGGER))
FTriggerNow
Figure 19. Snapshot Trigger Generation Logic
VIDEO
c: SnapshotMod || (SnapshotMod && TRIGGER)
LM9627
Functional Description (continued)
c:TRIGGER==1
SNAP
PREVIEW
a:FTriggerEn=1
c:TRIGGER==1
IRQ
a:SsTrigFlag=1
c:FTriggerEn==1
SNAP
a:FTriggerEn=0
PREVIEW
a: SsRdFlag = 1
a: FtTriggerEn = 0
Figure 20. Auto Snapshot Mode State Diagram
5.4
CPU Snapshot Mode
In CPU snapshot mode, the FTriggerEN is not set automatically
and an Interrupt generator can be enabled.
Hence, upon the receipt of a snapshot or FTriggerNow trigger
signal, the integrated timing and control circuit will generate an
internal TRIGGER signal as shown in figure 19 and then wait in
the IRQ state for the FTriggerEN bit to be manually set as shown
in figure 21.
Once the FtriggerEn bit is set the integrated timing and control
circuit will start resetting the array one row at a time. At end of
the reset cycle the timing and control circuit will signal the shutter to open via extsync pin or FtSync bit. At the end of the programmed integration time the shutter will be signalled to close,
and the pixel read-out will commence as shown in figure 18a. At
the end of the read-out sequence the FTriggerEN will be automatically disabled and the sensor will return to video capture
mode as shown in figure 20.
If an external shutter is not available then at least two frames
need to be taken so that the pixels can be integrated over one
frame as shown in Figure 18b.
To use CPU snapshot mode the SsEngage bit of the
SNAPSHOTMODE1 register must be set to one.
An interrupt generator can be enabled in CPU snapshot mode
by setting the SnapIntEn bit of SNAPSHOTMODE1 register. An
interrupt will be generated on the external interrupt pin, irq,
when a snapshot sequence is triggered (TRIGGER=1) or when
the array readout is complete at the end of the snapshot
sequence as shown figure 21.
Confidential
Figure 21. CPU Snapshot Mode State Diagram
When an interrupt is generated by a TRIGGER event, the
SsTrigFlag bit in the SNAPSHOTMODE1 register is set. Similarly when an interrupt is generated at the completion of a readout the SsRdFlag in the SNAPSHOTMODE1 register is set.
The polarity of the irq pin can be programmed. The interrupt can
only be cleared by reading SsTrigFlag and the SsRdFlag as
shown in figure 22.
SsTrigFlag
SsRdFlag
irq
SnapIntEn
IrqPol
Figure 22. Interrupt Request Generation Logic
5.5
Pulse & Level Trigger Mode
The snapshot pin can be programmed to operate in pulse trigger mode where one snapshot sequence is executed per active
pulse or in level trigger mode where by snapshot sequences are
repeated as long as the level on the snapshot pin is held active.
(see figures 20 and 21).
Pulse and level trigger modes can be set by programming the
SnapshotMod bit in the SNAPSHOTMODE0 register.
14
www.national.com
6.0
CLOCK GENERATION MODULE
The LM9627 contains a clock generation module that will create
two clocks as follows:
Hclk,
the horizontal clock. This is an internal system
clock and can be programmed to be the input
clock (mclk) or mclk divided by any number
between 1 and 255.
CLKpixel the pixel clock. This is the external pixel clock
that appears at the digital video port. It can be
Hclk or Hclk divided by 2. This clock cannot be
programed.
7.0
The number of rows in a scan window is given by:
SWN rows = (RADend - RADstart) + 1
Where:
RADend
RADstart
is the end row address of the defined scan window. (See section 2.1)
is the start row address of the defined scan window. (Scan section 2.1).
The number of Hclk clocks required to process a full frame is
given by:
FRAME RATE PROGRAMING
A frame is defined as the time it takes to reset every pixel in the
array, integrate the incident light, convert it to digital data and
present it on the digital video port. This is not a concurrent process and is characterized in a series of events each needing a
certain amount of time as shown in Figure 23.
FN Hclk = [(Mfactor * SWN rows ) + Fdelay ] * RNHclk
Where:
Mfactor
Start
Row address = 0
Progressive Scan
1
Sub-sampling or Interlace
0.5
SWN rows is the Number of Rows in Selected Scan Window.
Fdelay
a programmable value between 0 & 4097 repre-
Row delay time
senting the Inter Frame Delay in multiples of
RN Hclk . This parameter allows the frame time to
be extended. (See the Frame Delay High and
Frame Delay Low registers).
Row Time
Transfer all pixels to CDS
Reset all pixels in row
is a Mode Factor which must be applied. It is
dependent on the selected mode of operation as
shown in the table below:
The frame rate is given by:
Frame Rate =
Shift all pixels out of row
7.2
Partial Frame Integration
In some cases it is desirable to reduce the time during which the
pixels in the array are allowed to integrate incident light without
changing the frame rate.
Row address + 1
Yes
Last row?
No
Figure 23. Frame Readout Flow Diagram
7.1
Full Frame Integration
Full frame integration is when each pixel in the array integrates
light incident on it for the duration of a frame (see Figure 24).
The number of Hclk clock cycles required to process & shift out
one row of pixels is given by:
RN Hclk = R opcycle + R delay
Where:
R opcycle
R delay
Confidential
Hclk
FN Hclk
This is known as Partial Fame Integration and can be achieved
by resetting pixels in a given row ahead of the row being
selected for readout as shown in Figure 24. The number of Hclk
clocks required to process a partial frame is given by:
FPHclk = RN Hclk * Itime
Where:
RN Hclk
Itime
is the number of Hclk clock cycles required to
process & shift out one row of pixels.
is the number of rows ahead of the current row
to be reset. (See the Integration Time High and
Low registers).
The Integration time is subject to the following limits:
is a fixed integer value of 780 representing the
Row Operation Cycle Time in multiples of Hclk
clock cycles. It is the time required to carry out
all fixed row operations outlined in Figure 23.
a programmable value between 0 & 2047 representing the Row Delay Time in multiples of Hclk.
This parameter allows the Row Operation Cycle
time to be extended. (See the Row Delay High
and Row Delay Low registers).
Mode
15
Limit
Progressive Scan
Itime <= SWNrows + Fdelay
Interlace
Itime <= SWNrows + 2* Fdelay
Sub-Sampled
Itime <= SWNrows + 0.5*Fdelay
www.national.com
LM9627
Functional Description (continued)
LM9627
Functional Description (continued)
Full Integration Time
Partial Integration
Time
Row n
Frame
Delay
Row 0
Row 1
Row 2
Row x
Programmable Row Delay
Row x+∆
Row n
Frame
Delay
Row 0
Row CDS, Reset Row x & Shift
Full Frame integration
Programmable Row Delay
Row CDS, Reset Row x+∆ & Shift
Partial Frame Integration
Frame N
Figure 24. Partial and Full Frame Integration
7.3
Frame Rate Programming Guide
The table bellow can be used as a guide for programming the sensor. Note that it is assumed that the sensor is being driven with a
48MHz clock. All programmed values are given in decimal.
register
vclkgen
rdelayh
rdelayl
fdelayh
fdelayl
srows
srowe
dwlsb
address
05hex
15hex
16hex
17hex
18hex
0Bhex
0Chex
12hex
[10:8]
[7:0]
[11:8]
[7:0]
[8:1]
[8:1]
fps
30
4
0
0
0
9
0
251
50
15
4
0
0
2
40
0
251
50
7.5
4
0
0
6
12
0
251
50
3.75
4
3
12
6
12
0
251
50
25
4
0
172
0
0
0
251
50
12.5
5
0
0
1
226
0
251
50
6.25
5
0
0
5
188
0
251
50
3.125
4
0
156
14
14
0
251
50
5
4
2
255
4
23
0
251
50
4
5
0
0
10
12
0
251
50
3
5
0
0
14
14
0
251
50
2
6
0
200
13
248
0
251
50
1
6
3
241
15
126
0
251
50
Confidential
16
www.national.com
10.0 ANALOG GAIN ADJUSTMENT
8.0
The integrated analog programmable gain amplifier is capable
of applying a linear gain 1X to 5.6X in 64 linear steps. This can
be programmed using the VGAIN register as shown in the table
SIGNAL PROCESSING
8.1
Bad Pixel Detection & Correction
The LM9627 has a built-in bad pixel detection and correction
block that operates on the fly. This block can be switched off by
the user.
below:
8.2
Black Level Compensation
In addition to the programmable gain the LM9627 has a built in
black level compensation block as illustrated in Figure 25. This
block can be switched off.
*a
*(1-a)
+
Σ
+
z-1
Σ
+
compensated output
only enabled for black pixels
input signal
Figure 25. Digital Black Level Compensation.
The black level compensation block will subtract the average
signal level of the black pixels around the array from the digital
video output to compensate for the temperature and integration
time dependent dark signal level of the pixels. The exponential
averaging circuit shown in figure 25 only operates on the least
significant 8 bits of the video data.
9.0
POWER MANAGMENT
9.1
Power Up and Down
The LM9627 is equipped with an on-board power management
system allowing the analog and digital circuitry to be switched
off (power down) and on (power up) at any time.
The sensor can be put into power down mode by asserting a
logic one on the “pdwn” pin or by writing to the power down bit in
the main configuration register via the I2 C compatible serial
interface.
To power up the sensor a logic zero can be asserted on the
“pdwn” pin or write to the power down bit in the main configuration register via the I2 C compatible serial interface.
It will take a few milli seconds for all the circuits to power up. The
power management register contains a bit indicating when the
sensor is ready for use. During this time the sensor cannot be
used for capturing images. A status bit in the power management register will indicate when the sensor is ready for use.
9.2
Advanced Power Features
In addition to the power up/power down features of the sensor,
sections of the analog video processing chain can be powered
down and re-routed during normal operation. This flexibility
allows power dissipation to be traded of with signal gain as
shown in the table below:
PGA Amp
Power Saving
on
0mW
off
10mW
VidGain
VidGain
VidGain
Hex
Code
Gain
Amp
Value
VidGain
Dec
Code
Dec
Code
Hex
Code
Gain
Amp
Value
0
00
1
32
20
3.34
1
01
1.07
33
21
3.41
2
02
1.15
34
22
3.48
3
03
1.22
35
23
3.56
4
04
1.29
36
24
3.63
5
05
1.37
37
25
3.7
6
06
1.44
38
26
3.77
7
07
1.51
39
27
3.85
8
08
1.58
40
28
3.92
9
09
1.66
41
29
3.99
10
0A
1.73
42
2A
4.07
11
0B
1.8
43
2B
4.14
12
0C
1.88
44
2C
4.21
13
0D
1.95
45
2D
4.29
14
0E
2.02
46
2E
4.36
15
0F
2.1
47
2F
4.43
16
10
2.17
48
30
4.5
17
11
2.24
49
31
4.58
18
12
2.31
50
32
4.65
19
13
2.39
51
33
4.72
20
14
2.46
52
34
4.8
21
15
2.53
53
35
4.87
22
16
2.61
54
36
4.94
23
17
2.68
55
37
5.02
24
18
2.75
56
38
5.09
25
19
2.83
57
39
5.16
26
1A
2.9
58
3A
5.23
27
1B
2.97
59
3B
5.31
28
1C
3.04
60
3C
5.38
29
1D
3.12
61
3D
5.45
30
1E
3.19
62
3E
5.53
31
1F
3.26
63
3F
5.6
Figure 26. Power Control
Confidential
17
www.national.com
LM9627
Functional Description (continued)
LM9627
Functional Description (continued)
11.0 OFFSET ADJUSTMENT
12.0
For maximum image quality over a wide range of light conditions
it is necessary to set an appropriate offset voltage before using
the sensor to capture images. This offset voltage must be
applied to the offset pin (38) of the sensor, and is used to adjust
the analogue video signal being fed to the internal A/D.
The fine offset adjustment and calibration method described in
section 11.0 will ensure that the sensor’s black level is optimized
for a fixed analog gain setting. However, when the analog gain is
changed substantially, the black level of the sensor will shift
resulting in a white washed image.
To stop this effect from occurring, the black level needs to be recalibrated. This can be done as part of the contrast adjustment
which is carried out by most digital image processors. If this is
not possible then the following method can be used.
The relationship between the gain and the offset can be
described with the following equation.
The level of the offset voltage determines the black level of the
image and has a direct impact on the image quality. Too high an
offset results in a white washed or hazy looking image, while too
low of an offset results in a dark image with low contrast even
though the light conditions are good.
Offset(G) = Offset(0) + C * G0.4
A fine offset adjustment should be applied to each part by programming the offset voltage via the I2 C compatible serial interface. To program an offset voltage the following procedure
should be followed:
The sensor’s offset, fine_i & fine_ctrl pins should be connected
as shown in figure 2.
The following procedure should be followed to calibrate the offset
• Disable the black level compensation block by writing a logic
1 to bit 4 of the Main Configuration Register 0 (MCFG0:
address 02Hex).
• The offset can be adjusted by writing to the Offset Compensation Registers (OCR: addresses 1F, 22 & 25 hex). Writing
00hex will give the largest voltage, while writing FF hex will
give the smallest value.
• Run the following binary search algorithm
• For n=7 to 0 step -1
• {
Set bit n in the OCR registers (addresses 1F, 22 & 25
Hex) to a logic one by writing over the I 2 C compatible
interface.
Read a full frame and calculate the average black level
(BLaverage) of the first and last 5 black pixels in the every
row of the array
If (BLaverage < 100) then
Reset bit n in the OCR registers (addresses 1F, 22 &
25 Hex) to 0
else
Keep bit n set to one.
}
• Enable the black level compensation block (if desired) by writing a logic 0 to bit 4 of the Main Configuration Register 0
(MCFG0: address 02Hex).
Confidential
OFFSET & GAIN
where:
Offset(G)
is the offset that needs to be programmed in
the OCR1, OCR2 & OCR3 registers to ensure
the correct black level setting for an analog
gain setting of G.
Offset(0) is the offset that needs to be programmed in
the OCR1, OCR2 & OCR3 registers to ensure
the correct black level setting for unity analog
gain, (G=0).
C
is a constant and will vary from sensor to sensor
G
is the value programmed in the VGAIN register of the sensor which determines the sensor’s analog gain.
The following procedure should be used to calculate the value of
C:
Use the calibration procedure described in section 11.0 to determine the offset at unity gain, offset(0). Note the VGAIN register
should be set to 0.
Set the sensor’s analog gain register (VGAIN) to its max setting,
31, and repeat the calibration procedure described in section
11.0. This will allow the offset at full gain, 31, that needs to be
programmed in the OCR1, OCR2 & OCR3 registers to ensure
the correct black level setting to be determined.
The value of C for a particular sensor can be calculated using
the following formula:
C=
Offset(31) - Offset(0)
3.95
Once the value of C has been calculated, offset values for different gain settings can be calculated using equation 1. It is recommended that a two decimal point accuracy for C is maintained.
18
www.national.com
13.0 SERIAL BUS
The serial bus interface consists of the sda (serial data), sclk
(serial clock) and sadr (device address select) pins. The
LM9627 can operate only as a slave.
13.4 Data Valid
The master must ensure that data is stable during the logic 1
state of the sclk pin. All transitions on the sda pin can only occur
when the logic level on the sclk pin is “0” as shown in Figure 29.
The sclk pin is an input, it only and controls the serial interface,
all other clock functions within LM9627 use the master clock pin,
mclk.
13.1
Start/Stop Conditions
The serial bus will recognize a logic 1 to logic 0 transition on the
sda pin while the sclk pin is at logic 1 as the start condition. A
logic 0 to logic 1 transition on the sda pin while the sclk pin is at
logic 1 is interrupted as the stop condition as shown in Figure
27.
sda
sclk
S
P
start condition
stop condition
Figure 27. Start/Stop Conditions
13.2
Device Address
The serial bus Device Address of the LM9627 is set to 1010101
when sadr is tied low and 0110011 when sadr is tied high. The
value for sadr is set at power up.
13.3
Acknowledgment
The LM9627 will hold the value of the sda pin to a logic 0 during
the logic 1 state of the Acknowledge clock pulse on sclk as
shown in Figure 28.
sda
from master
MSB
ACK
sda
from sensor
sclk
ACK
S
1
7
2
8
9
Clock pulse
for ACK
START
Figure 28. Acknowledge
sda
sclk
data line
stable;
data valid
change
of data
allowed
data line
stable;
data valid
Figure 29. Data Validity
13.5 Byte Format
Every byte consists of 8 bits. Each byte transferred on the bus
must be followed by an Acknowledge. The most significant bit of
the byte is should always be transmitted first. See Figure 30.
13.6 Write Operation
A write operation is initiated by the master with a Start Condition
followed by the sensor’s Device Address and Write bit. When
the master receives an Acknowledge from the sensor it can
transmit 8 bit internal register address. The sensor will respond
with a second Acknowledge signaling the master to transmit 8
write data bits. A third Acknowledge is issued by the sensor
when the data has been successfully received.
The write operation is completed when the master asserts a
Stop Condition or a second Start Condition. See Figure 31.
13.7 Read Operation
A read operation is initiated by the master with a Start Condition
followed by the sensor’s Device Address and Write bit. When
the master receives an Acknowledge from the sensor it can
transmit the internal Register Address byte. The sensor will
respond with a second Acknowledge. The master must then
issue a new Start Condition followed by the sensor’s Device
Address and read bit. The sensor will respond with an Acknowledged followed by the Read Data byte.
The read operation is completed when the master asserts a Not
Acknowledge followed by Stop Condition or a second Start Condition. See Figure 32.
MSB
sda
ack signal
from receiver
ack signal
from receiver
byte complete
sclk
1
7
2
9
8
1
2
ACK clock line
8
9
ACK
held low
S
START
P
Figure 30. Serial Bus Byte Format
Device
Address
S
W
A
Register
Address
A
Data
Byte
A
P
bold sensor action
Figure 31. Serial Bus Write Operation
S
Device
Address
W
A
Register
Address
A
S
Device
Address
R
A
Data
Byte
_
A
P
bold sensor action
Figure 32. Serial Bus Read Operation
Confidential
19
www.national.com
LM9627
Functional Description (continued)
LM9627
Functional Description (continued)
14.0 DIGITAL VIDEO PORT
The captured image is placed onto a flexible 12-bit digital port as
shown in Figure 10. The digital video port consists of a programmable 12-bit digital Data Out Bus (d[11:0]) and three programmable synchronisation signals (hsync, vsync, pclk).
This feature allows a programmable digital gain to be implemented when connecting the sensor to 8 or 10 bit digital video
processing systems as illustrated in Figure 34. The unused bits
on the digital video bus can be optionally tri-stated.
By default the synchronisation signals are configured to operate
in “master” mode. They can be programed to operate in “slave”
mode.
LM9627
The following sections are a detailed description of the timing
and programming modes of digital video port.
Pixel data is output on a 12-bit digital video bus. This bus can be
tri-stated by asserting the TriState bit in the VIDEOMODE1 register.
d11
d10
d9
d8
d7
d6
d5
d4
d3
d2
d1
d0
d9
d8
d7
d6
d5
d4
d3
d2
d1
d0
10 bit
Digital
Image
Processor
a) LM9627 Connected to a 10 bit Digital Image Processors
14.1
Digital Video Data Out Bus (d[11:0])
A programmable matrix switch is provided to map the output of
the internal pixel framer to the pins of the digital video bus as
illustrated in Figure 33.
Internal Pixel Framer Output Register
11 10
9
8
7
6
5
4
3
2
1
0
LM9627
d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0
a) MSB Bit 11, Switch Mode (default)
d11
d10
d9
d8
d7
d6
d5
d4
d3
d2
d1
d0
d7
d6
d5
d4
d3
d2
d1
d0
8 bit
Digital
Image
Processor
b) LM9627 Connected to a 8 bit Digital Image Processors
Figure 34. Example of connection to 10/8 bit systems
Internal Pixel Framer Output Register
11 10
9
8
7
6
5
4
3
2
1
0
d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0
b) MSB Bit 10, Switch Mode
Internal Pixel Framer Output Register
9
11 10
8
7
6
5
4
3
2
1
0
Synchronisation Signals in Master Mode
By default the sensor’s digital video port’s synchronisation signals are configured to operate in master mode. In master mode
the integrated timing and control block controls the flow of data
onto the 12-bit digital port, three synchronisation outputs are
provided:
pclk
is the pixel clock output pin.
hsync
is the horizontal synchronisation output signal.
vsync
is the vertical synchronisation output signal.
14.2 Pixel Clock Output Pin (pclk) (Master Mode)
The pixel clock output pin, pclk, is provided to act as a synchronisation reference for the pixel data appearing at the digital
video out bus pins d[11:0]. This pin can be programmed to operate in two modes:
• In free running mode the pixel clock output pin, pclk, is always
running with a fixed period. Pixel data appearing on the digital
video bus d[11:0] are synchronized to a specified active edge
of the clock as shown in Figure 35.
pclk
d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0
d[11:0]
c) MSB bit 9, Switch Mode
a) pclk active edge negative
Internal Pixel Framer Output Register
11 10
9
8
7
6
5
4
3
2
1
0
pclk
d[11:0]
d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0
d) MSB bit 8, Switch Mode
Figure 33. Digital Video Bus Switching Modes
Confidential
b) pclk active edge positive (default)
invalid pixel data
Figure 35. pclk in Free Running Mode
• In data ready mode, the pixel clock output pin (pclk) will produce a pulse with a specified level every time valid pixel data
appears on the digital video bus d[11:0] as shown in Figure
36.
20
www.national.com
,
14.4 Vertical/Horizontal Synchronisation Pin (vsync)
The vertical synchronisation output pin, vsync, is used as an
indicator for pixel data within a frame. The vsync output pin can
be programmed to operate in two modes as follows:
pclk
d[11:0]
a) pclk active edge negative
pclk
d[11:0]
b) pclk active edge positive
invalid pixel data
Figure 36. pclk in Data Ready Mode
By default the pixel clock is a free running active low (pixel data
changes on the positive edge of the clock) with a period equal to
the internal hclk. The active edge of the clock can be programmed such that pixel data changes on the positive or negative edge of the clock.
• Level mode should be used when the pixel clock, pclk, is programmed to operate in free running mode. In level mode the
vsync output pin will go to the specified level (high or low) at
the start of each frame and remain at that level until the last
pixel of that row in the frame is placed on d[11:0] as shown in
Figure 39. The hsync level is always synchronized to the
active edge of pclk.
pclk
d[11:0]
vsync
Frame n+1
Frame n
a) vsync programmed to be active high
14.3
Horizontal Synchronisation Output Pin (hsync)
The horizontal synchronisation output pin, hsync, is used as an
indicator for row data. The hsync output pin can be programmed
to operate in two modes as follows:
• Level mode should be used when the pixel clock, pclk, is programmed to operate in free running mode. In level mode the
hsync output pin will go to the specified level (high or low) at
the start of each row and remain at that level until the last
pixel of that row is read out on d[11:0] as shown in Figure 37.
The hsync level is always synchronized to the active edge of
pclk.
pclk
d[11:0]
hsync
Row n
Row n+1
a) hsync programmed to be active high (default)
pclk
d[11:0]
vsync
pclk
d[11:0]
d[11:0]
hsync
pclk
d[11:0]
hsync
Row n+1
Row n
a) hsync programmed to be active high
vsync
d[11:0]
vsync
Frame n
Frame n+1
b) vsync programmed to be active low (default)
invalid pixel data
Figure 40. vsync in pulse mode
14.5 Odd/Even Mode
In odd/even mode the vsync signal is used to indicate when
pixel data from an odd and even field is being placed on the digital video bus d[11:0]. The polarity of vsync can still be programmed in this mode as shown in Figure 41
pclk
d[11:0]
d[11:0]
vsync
Row n
Row n+1
Odd Field
Even Field
a) vsync programmed to be active high (default)
b) hsync programmed to be active low
invalid pixel data
Figure 38. hsync in Pulse Mode
By default the first pixel data at the beginning of each row is
placed on the digital video bus as soon as hsync is activated. It
is possible to program up to 15 dummy pixels to be readout at
the beginning of each row before the real pixel data is readout.
This feature is supported for both level and pulse mode.
Confidential
Frame n+1
Frame n
a) vsync programmed to be active high
pclk
pclk
hsync
Frame n+1
• Pulse mode should be used when the pixel clock, pclk, is programmed to operate in data ready mode. In pulse mode the
vsync output pin will produce a pulse at the end of each
frame. The width of the pulse will be a minimum of four hclk
cycles and its polarity can be programmed as shown in Figure
40. The vsync level is always synchronized to the active edge
of pclk.
pclk
Row n+1
Row n
b) hsync programmed to be active low
invalid pixel data
Figure 37. hsync in Level Mode
• Pulse mode should be used when the pixel clock, pclk, is programmed to operate in data ready mode. In pulse mode the
hsync output pin will produce a pulse at the end of each row.
The width of the pulse will be a minimum of four pclk cycles
and its polarity can be programmed as shown in Figure 38.
The hsync level is always synchronized to the active edge of
pclk
Frame n
b) vsync programmed to be active low
invalid pixel data
Figure 39. vsync in Level Mode
pclk
d[11:0]
vsync
Odd Field
Even Field
b) vsync programmed to be active low
invalid pixel data
Figure 41. vsync in odd/even Mode
21
www.national.com
LM9627
Functional Description (continued)
LM9627
Functional Description (continued)
pclk
vsync
hsync
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
d[11:0]
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
row 2
row1
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
row 1
row 2
frame 1
frame 2
Programmable hsync to 1st valid pixel delay
Programmable inter-frame delay
Programmable row delay
Figure 42. Example of Digital Video Port Timing in Progressive Scan Mode
pclk
vsync
hsync
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
d[11:0]
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
row1
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
row 3
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9
row 2
row 4
Odd Field
Even Field
Programmable hsync to 1st valid pixel delay
Programmable inter-frame delay
Programmable row delay
Figure 43. Example of Digital Video Port Timing in Interlaced Mode
pclk
vsync
hysync
c0
d[11:0]
c2
c4
c6
c8
c0
row 1
c2
c4
c6
c8
c0
row 3
c2
c4
c6
c8
c0
c2
c4
row 1
c6
c8
row 3
frame 1
frame 2
Programmable hsync to 1st valid pixel delay
Programmable inter-frame delay
Programmable inter-row delay
Figure 44. Example of Digital Video Port Timing in 2:1 Sub-sampling Mode
pclk
vsync
hsync
c0
d[11:0]
c2
c4
c6
c8
c0
row 1
c2
c4
c6
c8
c0
row 2
c2
c4
c6
c8
c0
row 1
frame 1
c2
c4
c5
c8
row 2
frame 2
Programmable hsync to 1st valid pixel delay
Programmable inter-frame delay
Programmable inter-row delay
Figure 45. Example of Digital Video Port Timing in 4:2 Sub-sampling Mode
Confidential
22
www.national.com
14.6
Synchronisation Signals in Slave Mode
The sensor’s digital video port’s synchronisation signals can be
programmed to operate in slave mode. In slave mode the integrated timing and control block will only start frame and row processing upon the receipt of triggers from an external source.
Only two synchronization signals are used in slave mode as follows:
hsync
is the row trigger input signal.
vsync
is the frame trigger input signal.
Figure 46 shows the LM9627’s digital video port in slave mode
connected to a digital video processor master DVP.
d[11:0]
din[11:0]
hsync
RowTrig
vsync
FrameTrig
Xmclk = 124 + DWStAd
Where:
DW StAd
is the value of the display window column start
address.
The polarity of the active level of the row trigger is programmable. By default it is active high.
14.8 Frame Trigger Input Pin (vsync)
The frame trigger input pin, vsync, is used to reset the row
address counter and prepare the array for row processing. It
must be activated for at least one “mclk” cycle and no more than
96 mclk cycles after the activation of hsync as illustrated in Figure 48.
pclk
mclk
14.7 Row Trigger Input Pin (hsync)
The row trigger input pin, hsync, is used to trigger the processing of a given row. It must be activated for at least two “mclk”
cycle. The first pixel data will appear at d[11:0] “Xmclk “periods
after the assertion of the row trigger, were Xmclk is given by:
MasterClock
LM9627
DVP
Figure 46. LM9627 in slave mode
The polarity of the active level of the row trigger is programmable. By default it is active high.
780 clock cycles per line
hsync
pixel 12
pixel 11
pixel 652
d[11:0]
642 valid pixels
mclk
count
776 777 778 779
0
1
2
3
...
134 135 136 136 137
...
774 775 776 777 778 779
0
1
mclk
Figure 47. hsync slave mode timing diagram for centred display window of 642 pixels
780 clock cycles per line
hsync
No more than
96 clock cycles
vsync
internal row
counter
mclk
count
line502
line 502
776
777
778
779
0
1
2
3
...
line503
774 775 776 777 778 779
0
1
...
line 0
774 775 776 777 778 779
0
1
mclk
Figure 48. vsync slave mode timing diagram for scan window of 504 rows.
Confidential
23
www.national.com
LM9627
Functional Description (continued)
LM9627
MEMORY MAP
ADDR
Register
Reset Value
00h
Reserved for future use.
01h
REV
02h
Revision Register
02h
MCFG0
00h
Main Configuration Register 0
03h
MCFG1
00h
Main Configuration Register 1
04h
PCR
00h
Power Control Register.
05h
VCLKGEN
04h
Video Clock Generator
06h
VMODE0
00h
Video Mode 0 Register
07h
VMODE1
00h
Video Mode 1 Register
08h
VMODE2
00h
Video Mode 2 Register
09h
SNAPMODE0
00h
Snapshot Mode 0 Register
0Ah
SNAPMODE1
00h
Snapshot Mode 1 Register
0Bh
SROWS
00h
Scan Window Row Start Register
0Ch
SROWE
FBh
Scan Window Row End Register
0Dh
Confidential
Description
Reserved for future use.
0Eh
DROWS
00h
Display Window Row Start Register
0Fh
DROWE
FBh
Display Window Row End Register
10h
DCOLS
00h
Display Window Column Start Register
11h
DCOLE
A5h
Display Window Column End Register
12h
DWLSB
32h
Display Window LSB Register.
13h
ITIMEH
00h
Integration Time High Register
14h
ITIMEL
00h
Integration Time Low Register
15h
RDELAYH
00h
Row Delay High Register
16h
RDELAYL
00h
Row Delay Low Register
17h
FDELAYH
00h
Frame Delay High Register
18h
FDELAYL
00h
Frame Delay Low Register
19h
VGAIN
00h
Video Gain Register
1Fh
OCR1
00h
Offset Compensation Register 1
22h
OCR1
00h
Offset Compensation Register 1
25h
OCR2
00h
Offset Compensation Register 2
26h
BLCOEFF
00h
Black Level Compensation Coefficient Register
27h
BPTH0H
00h
Bad pixel Threshold 0 High Register
28h
BPTH0L
00h
Bad pixel Threshold 0 Low Register
29h
BPTH1H
00h
Bad pixel Threshold 1 High Register
2Ah
BPTH1L
00h
Bad pixel Threshold 1 Low Register
24
www.national.com
LM9627
Register Set
The following section describes all available registers in the
LM9627 register bank and their function.
Register Name
Mnemonic
Address
Type
Bit
7:0
Bit Symbol
SiRev
Register Name
Address
Mnemonic
Type:
Reset Value
Bit
7
6
5
Device Rev Register
REV
01 Hex
Read Only.
Bit
Description
Main Configuration 1
03 Hex
MCFG1
Read/Write
00 Hex
Bit Symbol
ColorMode
Assert when using a monochrome sensor. When this bit is
at a logic 1, Sub-Sampling is set
to 2:1 and every other row is
read out during interlace mode.
Clear (the default) when using a
color sensor. When this bit is at
logic 0, sub-sampling is set to
4:2 and every other row pair is
read out during interlace mode.
6
ScanMode
Assert to set the sensor to interlace readout mode. Clear (the
default) to set the sensor to progressive scan read out mode.
5
HSubSamEn
Assert to enable horizontal subsampling. Clear (the default) to
disable horizontal sub-sampling.
4
VSubSamEn
Assert to enable vertical subsampling. Clear (the default) to
disable vertical sub-sampling.
Main Configuration 0
02 Hex
MCFG0
Read/Write
00 Hex
PwrUpBusy
PwrDown
BPCorrection
Description
(Read Only Bit)
Indicates that power on initialization is in progress. The sensor is
ready for use when this bit is at
logic 0.
Assert to power down the sensor.
Writing a logic 1 to this register bit
has the same effect as taking the
pdwn pin high. Clear (the default)
this bit to power up the sensor.
Assert to enable the bad pixel
detection and correction circuit.
Clear (the default) to switch it off.
4
BlkLComp
Assert to disable the black level
compensation circuit. Clear (the
default) to switch it on.
3
SnapEnable
Assert to enable the external
snapshot pin. Clear (the default)
to disable the external snapshot
pin.
Reserved
3
2
Reserved
SlaveMode
1:0
Use to configure the digital
video port’s synchronisation signal to operate in slave mode. By
default the digital video’s port’s
synchronization signals are configured to operate in master
mode.
Reserved
Register Name
Address
Mnemonic
Type
Power Control Register 1
04 Hex
PCR
Read/Write
Reset Value
00 Hex
Bit
7
Bit Symbol
ByPassGain
6:4
3
0
25
Description
Assert to route the analog video
signal from the output of the CDS
to the input of the 12 bit A/D. Clear
(the default) to route the signal to
the video gain amplifier.
Reserved
PwdnPGA
2:1
Confidential
Description
7
The silicon revision register.
Bit Symbol
2:0
Register Name
Address
Mnemonic
Type
Reset Value
Assert to power down the programmable video gain amplifier.
Clear (the default) to power up the
video gain amplifiers.
Reserved
PwDnADC
Assert to power down the 12 bit
analog to digital convertor. Clear
(the default) to power up the 12 bit
analog to digital convertor.
www.national.com
LM9627
Register Set (continued)
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:0
Bit Symbol
HclkGen
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:6
Hclk Generator Register
05 Hex
VCLKGEN
Read/Write
04 Hex.
Use to divide the frequency of
the sensors master clock input,
mclk to generate the internal
sensor clock, Hclk.
Program 00 Hex (the default) for
Hclk to equal mclk or divide
mclk by any number between 1
and FF Hex.
Digital Video Mode 0
06 Hex
VMODE0
Read/Write
00 Hex
Bit Symbol
PixDataSel
PixDataMsb
3:0
7
PixClkMode
6
VsyncMode
5
HsyncMode
4
PixClkPol
3
VsynPol
2
HsynPol
1
OddEvenEn
0
TriState
Description
Description
Use to program the number of
active bits on the digital video bus
d[11:0], starting from the MSB
(d[11]). Inactive bits are tri-stated.:
00
5:4
Register Name Digital Video Mode 1
Address
07 Hex
Mnemonic
VMODE1
Type
Read/Write
Reset Value
00 Hext
Bit
Bit Symbol
Description
12 bit mode, bits
d[11:0] of the digital
video bus are active.
This is the default.
01
10 bit mode, bits
d[11:2] of the digital
video bus are active.
10
8 bit mode, bits
d[11:4] of the digital
video bus are active.
11
Reserved.
Use to program the routing of the
MSB output of the internal video
A/D to a bit on the digital video
bus.
00
A/D [11:0] -> d[11:0].
01
A/D [10:0] -> d[11:1]
10
A/D [9:0] -> d[11:2]
11
A/D [8:0] -> d[11:3]
Reserved
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:4
3:0
Confidential
26
Assert to set the pclk to “data
ready mode”. Clear, the default, to
set pclk to “free running mode”.
Assert to set the vsync pin to
“pulse mode”. Clear (the default)
to set the vsync signal to “level
mode”.
Assert to force the hsync signal to
pulse for a minimum of four pixel
clocks at the end of each row.
Clear (the default) to force the
hsync signal to a level indicating
valid data within a row.
Assert to set the active edge of
the pixel clock to negative. Clear
(the default) to set the active edge
of the clock to positive.
Assert to force the vsync signal to
generate a logic 0 during a frame
readout (Level Mode), or a negative pulse at the end of a frame
readout (Pulse Mode). Clear (the
default) to force the vsync signal
to generate a logic 1 during a
frame readout (Level Mode), or a
negative pulse at the end of a
frame readout (Pulse Mode).
Assert to force the hsync signal to
generate a logic 0 during a row
readout (Level Mode), or a negative pulse at the end of a row
readout (Pulse Mode). Clear (the
default) to force the hsync signal
to generate a logic 1 during a row
readout (Level Mode), or a negative pulse at the end of a readout
(Pulse Mode).
Assert to force the vsync pin to act
as an odd/even field indicator.
Clear (the default) to force the
vsync pin to act as a vertical synchronization signal.
Assert to tri-state all output signals
(data and control) on the digital
video port. Clear (default) to
enable all signals (data and control) on the digital video port.
Digital Video Mode 2
08 Hex
VMODE2
Read/Write
00 Hex
Bit Symbol
Description
HsyncAdjust
Use to program the leading edge
of hsync to the first valid pixel at
the beginning of each row. This
can be 0-hex to F-hex corresponding to 0 - 15 pixel clocks.
Default 0.
Reserved
www.national.com
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7.6
Snapshot Mode Configuration Register 0
09 Hex
SNAPMODE0
Read/Write
00 Hex
Bit Symbol
SsFrames
Program to set the number of
frames required before readout
during a snapshot with no external
shutter, (see Figure 18). By
default these two bits are set to 00
resulting in one frame before
readout:
0
one frame
01
two frames
10
three frames
11
four frames
ShutterEn
Assert to indicate that an external
shutter will be used during snapshot mode. Clear (the default) to
indicate that snapshot mode will
be carried out without the aid of an
external shutter.
4
ExtSynPol
Assert to set the active level of the
extsync signal to 0. Clear (the
default) to set the active level of
the extsync signal to 1.
2
1
0
Bit
Description
5
3
Register Name
Address
Mnemonic
Type
Reset Value
Snapshot Mode Configuration Register 1
0A Hex
SNAPMODE1
Read/Write
00 Hex.
Bit Symbol
7
SnapIntEn
Assert to enable the snapshot
interrupt generator. Clear (the
default) to disable the interrupt
generator.
6
SsTrigFlag
(Read Only Bit)
Snapshot trigger interrupt flag.
A logic 1 in this bit indicates that
the generated interrupt on the
irq pin is due to a snapshot trigger. This bit is cleared when
read.
5
SsRdFlag
(Read Only Bit)
Snapshot read done interrupt
flag. A logic 1 in this bit indicates
that the generated interrupt on
the irq pin is due to the completion of a snapshot readout
sequence. This bit is cleared
when read.
4
SsEngage
Assert to allow a CPU controlled
snapshot sequence. In this
mode the snapshot trigger will
only generate an interrupt to the
CPU and the CPU must manually start the snapshot sequence
by asserting the FTriggerEn bit
of this register.
Clear (the default) engage an
automatic snapshot sequence.
In auto mode the snapshot
sequence is started as soon as
a snapshot trigger is asserted.
3
FtSync
(Read Only Bit)
The internal synchronisation
signal. A logic 1 on this bit indicates a synchronization event is
required. This bit is functionally
equivalent to the external
extsync pin.
2
FtBusy
(Read Only Bit)
The Frame Trigger Busy bit. A
logic 1 on this bit indicates that
the sensor is busy reading out
pixel data as shown in Figure
18.
1
FTriggerNow
Assert to start a snapshot
sequence. The frame trigger
now is functionally equivalent to
the external snapshot pin. The
default is 0.
0
FTriggerEn
Assert to enable a snapshot
sequence (see the SsEngage
bit of this register). The default
is 0.
Reserved
SnapshotMod
SnapShotPol
IrqPol
Confidential
Assert to set the snapshot pin to
level mode. In level mode the sensor will continually run snapshot
sequences as long as the snapshot pin is held to the active level.
Clear (the default) to set the snapshot signal to pulse mode. In
pulse mode the sensor will only
carry out one snapshot sequence
per pulse applied to the snapshot
pin.
Assert to set the snapshot pin to
be active on the positive edge.
Clear (the default) to set the snapshot pin to be active on the negative edge.
Assert to set the active level of the
irq signal to 0, Clear (the default)
to set the active level of the irq
signal to 1.
27
Description
www.national.com
LM9627
Register Set (continued)
LM9627
Register Set (continued)
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:0
Bit Symbol
Description
SwStartRow
Use to program the scan window’s
start row address MSBs. If bit 6 of
register DWLSB is set to 1 the
start row address is incremented
by 1 else the raw value is used.
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:0
Scan Window Row Start Register
0B Hex
SROWS
Read/Write
00 Hex
Scan Window Row End Register
0C Hex
SROWE
Read/Write
FB Hex
Bit Symbol
SwEndRow
Use to program the scan window’s
end row address MSBs. If bit 6 of
register DWLSB is set to 1 the end
row address is incremented by 1.
else the raw value is used.
Display Window Row Start Register
0E Hex
DROWS
Read/Write
Reset Value
00 Hex
7:0
Bit
7:0
Description
DwStartRow
Use to program the display window’s start row address MSBs.
The LSB can be programmed
using the DWLSB register.
Bit
7:0
Description
DwEndRow
Use to program the scan window’s
end row address. The LSB can be
programmed using the DWLSB
register.
Display Window Column Start Register
10 Hex
DCOLS
Read/Write
00 Hex
Bit Symbol
DwStartCol
Register Name
Address
Mnemonic
Type
Reset Value
Use to program the display window’s start column address
MSBs. The two LSBs can be programmed using the DWLSB register.
Display Window Column End Register
11 Hex
DCOLE
Read/Write
A5 Hex
DwEndCol
Description
Use to program the scan window’s
end column address MSBs. The
two LSBs can be programmed
using the DWLSB register.
Display Window LSB register
12 Hex
DWLSB
Read/Write
32 Hex
Bit Symbol
7
28
Description
Bit Symbol
Register Name
Address
Mnemonic
Type
Reset Value
Display Row End Register
0F Hex
DROWE
Read/Write
FB Hex
Bit Symbol
Confidential
7:0
Bit
Bit Symbol
Register Name
Address
Mnemonic
Type
Reset Value
Bit
Description
Register Name
Address
Mnemonic
Type
Bit
Register Name
Address
Mnemonic
Type
Reset Value
Description
Reserved
6
SwLsb
Assert to increment the value of
the scan window start and end
row addresses by 1. Clear (the
default) to use the raw values.
5
DwCel[1]
Use to program bit 1 of the display
window’s end column address.
Default is 1.
4
DwCel[0]
Use to program bit 0 of the display
window’s end column address.
Default is 1.
3
DwCSL[1]
Use to program bit 1 of the display
window’s start column address.
Default is 0.
2
DwCSL [0]
Use to program bit 0 of the display
window’s start column address.
Default is 0.
1
DwERLsb
Use to program bit 0 of the display
window’s end row address.
Default is 1.
0
DwSRLsb
Use to program bit 0 of the display
window’s start row address.
Default is 0.
www.national.com
Register Name
Address
Mnemonic
Type
Reset Value
Bit
Integration Time High Register
13 Hex
ITIMEH
Read/Write
00 Hex.
Bit Symbol
7:4
3:0
Register Name
Address
Mnemonic
Type
Reset Value
Bit
Description
7:0
Reserved
Itime[11:8]
Register Name
Address
Mnemonic
Type
Reset Value
Program to set the integration
time of the array. The value programmed in the register is the
number of rows ahead of the
selected row to be reset.
Bit
7:0
Bit Symbol
Itime[7:0]
Register Name
Address
Mnemonic
Type
Reset Value
Program to set the integration
time of the array. The value programmed in the register is the
number of rows ahead of the
selected row to be reset.
Row Delay High Register
15 Hex
RDELAYH
Read/Write
00 Hex.
Bit Symbol
7:3
2:0
Rdelay[10:8]
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:0
Use to program the MSBs of the
row delay.
Row Delay Low Register
16 Hex
RDELAYL
Read/Write
00 Hex
Bit Symbol
Rdelay[7:0]
Register Name
Address
Mnemonic
Type
Reset Value
7:0
Use to program the LSBs of the
row delay.
Frame Delay High Register
17
FDELAYH
Read/Write
00 Hex
Bit Symbol
7:4
3:0
Bit Symbol
OffsetVol
Bit
Description
Description
This register defines the voltage level appearing on the
offset_ctrl pin.
Offset Compensation Register 1
22 Hex
OCR1
Read/Write
00 Hex
Bit Symbol
OffsetVol
Register Name
address
Mnemonic
Type
Reset Value
Use to program the overall video
gain. 00hex corresponds to a gain
of 0dB while 3Fhex corresponds
to a gain of 15dB. Steps are in linear increments.
Offset Compensation Register 0
1FHex
OCR0
Read/Write
00 Hex
Description
7:0
Bit
VidGain
Register Name
address
Mnemonic
Type
Reset Value
Bit
Description
Reserved
Description
Reserved
Use to program the LSBs of
the frame delay.
Bit Symbol
Register Name
address
Mnemonic
Type
Reset Value
Bit
Description
Video Gain Register
19 Hex
VGAIN
Read/Write
00 Hex
Description
7:0
Bit
FDelay [7:0]
7:6
5:0
Bit
Bit Symbol
Register Name
Address
Mnemonic
Type
Reset Value
Integration Time Low Register
14 Hex
ITIMEL
Read/Write
00 Hex.
Frame Delay Low Register
18 Hex
FDELAYL
Read/Write
00 Hex
Description
This register defines the voltage level appearing on the
offset_ctrl pin.
Offset Compensation Register 2
25 Hex
OCR2
Read/Write
00 Hex
Bit Symbol
OffsetVol
Description
This register defines the voltage level appearing on the
offset_ctrl pin.
Reserved
FDelay[11:8]
Confidential
Use to program the MSBs of the
frame delay.
29
www.national.com
LM9627
Register Set (continued)
LM9627
Register Set (continued)
Register Name Black Level
Register
Address
26 Hex
Mnemonic
BLCOEFF
Type
Read/Write
Reset Value
00 Hex
Bit
7:0
Bit Symbol
Alpha[7:0]
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:0
BpT0 [11:4]
Bit
7:4
Bit Symbol
BpT0 [3.0]
Exponential averaging coefficient for black pixels
Description
Use to program the MSBs of
the bad pixel correction
threshold 0.
Description
Use to program the LSBs of
the bad pixel correction
threshold 0.
Reserved
Register Name
Address
Mnemonic
Type
Reset Value
Bit
Threshold 1 High Register
29 Hex
BPTH1H
Read/Write
00 Hex
Bit Symbol
THR1[11.4]
Register Name
Address
Mnemonic
Type
Reset Value
Bit
7:4
Description
Threshold 0 Low Register
28 Hex
BPTH0L
Read/Write
00 Hex
3:0
7:0
Coefficient
Threshold 0 High Register
27 Hex
BPTH0H
Read/Write
00 Hex.
Bit Symbol
Register Name
Address
Mnemonic
Type
Reset Value
Compensation
THR1 [3.0]
Confidential
Use to program the MSBs of
the bad pixel correction
threshold 1.
Threshold 1 Low Register
2A Hex
BPTH1L
Read/Write
00 Hex
Bit Symbol
3:0
Description
Description
Use to program the LSBs of
the bad pixel correction
threshold 1.
Reserved
30
www.national.com
LM9627
Timing Information
1.0
DIGITAL VIDEO PORT MASTER MODE TIMING
pclk
hsync
t2
t1
d[11:0]
P0
Pn
P1
t3
Figure 49. Row Timing Diagram
pclk
vsync
t6
t5
R2
hsync
Rn
R3
t1
t2
Figure 50. Frame Timing
pclk
vsync
t6
t5
hsync
Fdelayn-2
Fdelayn-1
F delayn
R0
R1
R2
Rn
t2
t1
Inter Frame Delay
Frame (n)
Figure 51. Frame Delay Timing (With Inter Frame Delay).
Label
Descriptions
Min
Typ
Max
t0
pclk period
74.4ns
83.3ns
1.0µs
t1
t2
t3
t5
t6
Note a:
Note b:
hsync low
level mode
pulse mode
(116-HsyncAdjust) *pclk
16 * pclk
(see note a & b)
hsync high
level mode
pulse mode
(664 -HsyncAdjust) *pclk
764 * pclk
(see note a & b)
first valid pixel data after hsync active
HsyncAdjust * pclk
(see note a & b)
vsync low
level mode
pulse mode
116 *pclk
16 * pclk
vsync high
level mode
pulse mode
(FN Hclk - 116) * pclk
16 * pclk
(see note a & b)
(see note a & b)
See Frame Rate Programming section for more details
See Digital Video Port Registers for more details
Confidential
31
www.national.com
LM9627
Timing Information (continued)
d[11:0]
hsync
vsync
pclk
t1
t2
Figure 52. d[11:0], hsync & vsync to Active High pclk Timing
d[11:0]
hsync
vsync
pclk
t3
t4
Figure 53. d[11:0], hsync & vsync to Active Low pclk Timing
The following specifications apply for all supply pins = +3.3V and C L = 10pF unless otherwise noted. Boldface limits apply for TA =
TMIN to T MAX: all other limits TA = 25o C (Note 7)
Label
Descriptions
t1
Rising pclk to Rising hsync, vsync or d[11:0]
25ns
t2
Rising pclk to Falling hsync, vsync or d[11:0]
23ns
t3
Falling pclk to rising hsync, vsync or d[11:0]
25ns
t4
Falling pclk to falling hsync, vsync or d[11:0]
23ns
Confidential
Min
32
Typ
Max
www.national.com
LM9627
Timing Information (continued)
2.0
DIGITAL VIDEO PORT SLAVE MODE TIMING
t1
t3
trigger row n
hsync
trigger row n+1
t2
d[11:0]
P652
P653
P640
P654
P652
P1
P653
P654
P655
mclk
Row n-1
Row n
Figure 54. Slave Mode Row Trigger and Readout Timing
trigger last row
in frame n
hsync
t5
trigger Frame n+1
vsync
mclk
t4
Figure 55. Slave Mode d[11:0], hsync & vsync to pclk Timing
d[11:0]
mclk
t6
Figure 56. Rising Edge of mclk to Valid Pixel Data
The following specifications apply for all supply pins = +3.0V & CL = 10pF unless otherwise noted. Boldface limits apply for TA =
TMIN to T MAX: all other limits TA = 25o C (Note 7)
Label
Descriptions
Min
t1
Pulse width of row trigger
2 * mclk
t2
First pixel out after rising edge of row trigger
124 * mclk
t3
Minimum time between row triggers.
780 * mclk
t4
Max time to assert next frame trigger after last row
trigger.
t5
Pulse width of Frame trigger
t6
Time to valid pixel data after rising edge of mclk
Confidential
Typ
Max
124 * mclk
96 * mclk
2 * mclk
44ns
33
www.national.com
LM9627
Timing Information (continued)
3.0
DIGITAL VIDEO PORT SINGLE FRAME CAPTURE (SNAPSHOT MODE) TIMING
t1
snapshot or FTriggerNow
irq
FTriggerEn
extsync or FtSync
FtBusy
t4
t3
t2
Figure 57. Snapshot Mode Timing With External Shutter
t1
snapshot or FTriggerNow
irq
FTriggerEn
extsync or FtSync
FtBusy
t3
t2
t4
Figure 58. Snapshot Timing Without External Shutter
Label
Descriptions
Equation
t1
Minimum Snapshot Trigger Pulse Width
2 * mclk
(see notes a & b)
t2
Minimum time from Snapshot Pulse to extsync
FN Hclk
(see notes a & b)
t3
Array Integration Time
FN Hclk
(see notes a & b)
t4
Pixel Read Out
FN Hclk
Note a:
Note b:
(see notes a & b)
See 7.0Frame Rate Programming section for more details
See Snapshot Mode for more details
Confidential
34
www.national.com
LM9627
Timing Information (continued)
4.0
SERIAL BUS TIMING
Sr
Sr
P
tfDA
tfDA
SDA
tSU;STA
tHD;DAT
tHD;STA
t SU;STO
tSU;DAT
SCLK
trCL
trCL1
trCL
trCL1
= Rp resistor pull-up
tHIGH
tLOW
tLOW
(1)
tHIGH
= MCS current source pull-up
(1) Rising edge of the first SCLK pulse after an acknowledge bit.
Figure 59. I 2 C Compatible Serial Bus Timing.
The following specifications apply for all supply pins = +3.3V, CL = 10pF, and sclk = 400KHz unless otherwise noted. Boldface limits
apply for TA = TMIN to T MAX: all other limits T A = 25o C (Note 7)
Confidential
PARAMETER
SYMBOL
MIN
MAX
UNIT
sclk clock frequency
fSCLH
0
400
KHz
Set-up time (repeated) START condition
tSU;STA
0.6
-
µS
Hold time (repeated) START condition
tHD;STA
0.6
-
µS
LOW period of the sclk clock
tL O W
1.3
-
µS
HIGH period of the sclk clock
tHIGH
0.6
-
µS
Data set-up time
tSU;DAT
180
-
nS
Data hold time
tHD;DAT
0
0.9
µS
Set-up time for STOP condition
tSU;STO
0.6
Capacitive load for sda and sclk lines
Cb
35
µS
400
pF
www.national.com
LM9627
Array Mechanical Information
.440 +/-.005 TYP
[11.18 +/- 0.12]
.040 +/-.003 TYP
[1.02 +/- 0.07]
43
.085 +/-.010
[2.16 +/- 0.25]
48
.060 +.010 TYP
-.005
[1.52 + 0.25]
[- 0.12]
6
1
7
42
distance from pixel (die surface) to top surface of
glass lid= 0.894 mm
R.0075 +/-.0050
[0.191+/- 0.127]
TYP
.020 +/-.003
[0.51 +/- 0.07]
TYP
0.328
[8.325]
Note 3
31
18
30
.040 +/-.007 TYP
[1.02 +/- 0.17]
19
0.281
[7.131]
Note 3
Optical Center of
Sensor Array
(4X R.0075)
[0.19]
.560 +.012
-.005
[14.22 + 0.30]
[ - 0.12]
.102 MAX
[2.58]
Notes:
1. Controlling dimensions are in inches, values in [] are in millimeters
2. All Exposed metallized areas shall be gold plated 60 micro-inches [1.52 micrometers] minimum thickness over nickel plate
3. Reference dimensions only. Tolerance will depend on die placement [+/-0.1 mm].
4. Reference JEDEC registration MS-009, variation AF issue A, dated 9/29/1980.
Confidential
36
www.national.com
LM9627 Color CMOS Image Sensor VGA 30 FPS
LIFE SUPPORT POLICY
NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in
a significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support @ nsc.com
www.national.com
National Semiconductor Europe
Fax: +49 (0) 1 80-530 85 86
Email: europe.support @ nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Francais Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.