SPECIFICATION MODEL LCM-40 SELECTABLE CURRENT Note.3 350mA 2 ~ 100V RATED POWER 42W RIPPLE CURRENT OUTPUT 500mA 2 ~ 80V ¢º F 110 M 600mA 700mA 900mA 1050mA 2 ~ 57V 2 ~ 45V 2 ~ 40V 200mVp-p RIPPLE & NOISE (max.) Note.2 700mVp-p 65V ¡Ó5.0% CURRENT ACCURACY Note.6 1000ms, 80ms / 230VAC at rated power SETUP, RISE TIME 16ms/230VAC at rated power HOLD UP TIME (Typ.) VOLTAGE RANGE Note.4 180 ~ 295VAC ¡Ù EFFICIENCY (Typ.) Note.7 91% eli 0.21A/230VAC 0.17A/277VAC COLD START 35A/230VAC LEAKAGE CURRENT <0.5mA / 240VAC SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed 110 ~ 130V Protection type : Shutdown o/p voltage, re-power on to recover OVER VOLTAGE OVER TEMPERATURE 90 ¢J ¡Ó10¢J (RTH2) Protection type : Shut down o/p voltage, re-power on to recover ¡Ó TEMP. COMPENSATION 12V @ 50mA for driving fan; Tolerance 5% By external NTC(not provide with the power supply), please see "Temperature Compensation Operation" AUXILIARY POWER DIMMING Please see "Dimming Operation" SYNCHRONIZATION Please see "Synchronization Operation" WORKING TEMP. -30 ~ +60 EMC ¢J ¡Ó0.03%/¢J (0 ~ 50¢J) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL8750, ENEC EN61347-1, EN61347-2-13,EN62384 independent approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55015, EN61000-3-2 Class C( 35% rated power) ; EN61000-3-3 EMC EMISSION EMC IMMUNITY DIMENSION PACKING NOTE -40 ~ +80 , 10 ~ 95% RH VIBRATION MTBF OTHERS ¢J (Refer to "Derating Curve") 20 ~ 90% RH non-condensing Pr WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT SAFETY & ¡Ù POWER FACTOR (Typ.) PF 0.98/230VAC, PF 0.97/277VAC at rated power (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION Total harmonic distortion will be lower than 20% when output loading is 75% or higher AC CURRENT (Typ.) INRUSH CURRENT(Typ.) FUNCTION 254 ~ 417VDC 47 ~ 63Hz FREQUENCY RANGE PROTECTION SELV 2 ~ 67V NO LOAD OUTPUT VOLTAGE (max.) 110V INPUT M mi DC VOLTAGE RANGE Features : series Output current level selectable by DIP S.W. 180~295VAC input only Built-in active PFC function Protections: Short circuit / Over voltage / Over temperature Cooling by free air convection Fully isolated plastic case Class power unit, no FG Built-in 0~10Vdc and PWM signal dimming function Built-in 12V/50mA auxiliary output IP20 design Temperature compensation function by external NTC No load power consumption <1W@AC always on (Note 8) Power supplies synchronization function up to 10 units Suitable for LED lighting applications 3 years warranty na ¡¡E¡½ E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡ E LCM-40 ry 40W Multiple-Stage Output Current LED Power Supply ¢J ¡Ù Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547 light industry level (surge 2KV), criteria A K hrs min. MIL-HDBK-217F (25 ) 123.5*81.5*23mm (L*W*H) 0.24Kg ¢J ¢J 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf parallel capacitor. 3. Please see "DIP switch table". 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. Efficiency is measured at 500mA/80V output set by DIP switch. 8. No load power consumption<1W is measured at 180~277VAC. File Name:LCM-40-SPEC 2012-09-11 ry LCM-40 40W Multiple-Stage Output Current LED Power Supply Mechanical Specification Case No. 123.5 6.75 6.75 110 AC/L AC/N TB3/TB4 1 SYN. 2 3 4 5 6 68 81.5 2- £r4. 2 6.75 Unit:mm na 6.75 series CN101 CN100 + Vo - ON 1 2 3 4 5 6 39.3 65.5 7.8 7.8 2- M3 4 mi Terminal Pin No. Assignment(TB3/TB4) : 23 Pin No. 1 2 3 Assignment +12Vaux. -12Vaux. +NTC Assignment -NTC DIM+ DIM- Pin No. 4 5 6 SYN. Connector(CN101/CN100):JST B2B-XH or equivalent Pin No. 1,3 2,4 eli Block Diagram EMI FILTER & RECTIFIERS I/P POWER SWITCHING PFC CIRCUIT O.L.P. PFC CONTROL O.T.P. Pr +V -V DIM+ DIM- DETECTION CIRCUIT 80 70 LOAD (%) LOAD (%) RECTIFIERS & FILTER 90 20 40 +12Vaux 100 40 30 RECTIFIERS Static Characteristics 60 15 JST SXH-001T-P0.6 or equivalent O.V.P. 80 0 Terminal JST XHP or equivalent O.L.P. 100 -15 Mating Housing PFC fosc : 60KHz PWM fosc : 80KHz PWM CONTROL Derating Curve -30 Assignment + - 50 ¢J AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 180 190 200 210 220 230 240 250 260 270 280 295 INPUT VOLTAGE (V) 60Hz File Name:LCM-40-SPEC 2012-09-11 ry LCM-40 40W Multiple-Stage Output Current LED Power Supply DIP Switch Table series DIP S.W. 1 2 3 4 5 6 350mA ---- ---- ---- ---- ---- ---- 500mA ON ---- ---- ---- ---- ---- 600mA(Factory Setting) ON ON ---- ---- ---- ---- 700mA ON ON ON ---- ---- ON 900mA ON ON ON ON ---- ON 1050mA ON ON ON ON ON ON Io mi Power Factor Characteristic na LCM-40 is a multiple-stage output current supply, selection of output current through DIP switch as table below. Constant Current Mode 0.99 0.96 0.93 0.9 350 0.87 0.84 500 0.81 600 0.78 PF PF Constant Current Mode 700 0.75 900 0.72 1050 0.66 0.63 eli 0.69 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 0.99 0.96 0.93 0.9 0.87 0.84 0.81 0.78 0.75 0.72 0.69 0.66 0.63 0.6 0.57 0.54 0.51 0.48 0.45 10% 20% 30% (40W) LOAD (230Vac Input) 350 500 600 700 900 1050 40% 50% 60% 70% 80% 90% 100% (40W) LOAD (277Vac Input) EFFICIENCY vs LOAD LCM-40 series possess superior working efficiency that up to 91% can be reached in field applications. 95.0% Pr 90.0% 95.0% 90.0% 85.0% 80.0% 350 75.0% 500 70.0% 600 65.0% 700 60.0% 900 55.0% 1050 50.0% 45.0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD (230Vac Input) EFFICIENCY (%) EFFICIENCY (%) 85.0% 80.0% 350 75.0% 500 70.0% 600 65.0% 700 60.0% 900 55.0% 1050 50.0% 45.0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD (277Vac Input) File Name:LCM-40-SPEC 2012-09-11 ry LCM-40 40W Multiple-Stage Output Current LED Power Supply na DIMMING OPERATION series mi ¡° Built-in 2 in 1 dimming function, output constant current level can be adjusted through output terminal by 0 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-. ¡° Please DO NOT connect "DIM-" to "-V". ¡° 0 ~ 10V dimming function for output current adjustment (Typical) Dimming value 0V 1V Output current 0% 10% 2V 3V 4V 5V 6V 7V 8V 9V 10V OPEN 20% 30% 40% 50% 60% 70% 80% 90% 100% 100%~108% ¡° 10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz 0% 10% Output current 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% OPEN 20% 30% 40% 50% 60% 70% 80% 90% 100% 100%~108% eli Duty value SYNCHRONIZATION OPERATION ¡E10 drivers(max.) synchronization (1 master + 9 slaves ) ¡EMaximum length of the cable from first driver to last driver is 15 meter. SYN. - - LCM-40 (Slave 1) SYN. - - + + LCM-40 (Master) + + + + SYN. - - Pr LCM-40 (Slave 2) File Name:LCM-40-SPEC 2012-09-11 ry 40W Multiple-Stage Output Current LED Power Supply TEMPERATURE COMPENSATION OPERATION NTC derating curve series na 105 LCM-40 100 £[ £[ 470KO 470K £[ 220KO 220K 95 Output Io (%) 330KO 330K 90 85 80 75 65 55 60 65 70 mi 70 75 80 85 90 95 Sensed Temperature(degree) ¡ô ¡õ LCM-40 have the built-in temperature compensation function (T ,Io ) . By connecting a temperature sensor (NTC resistor) between the NTC +/terminal of LCM-40 and the detecting point on the lighting system or the surrounding environment, output current of LCM-40 could be correspondingly changed to ensure the long life of LED. 1.LCM-40 can still be operated well when the NTC resistor is not connected and the value of output current is set by user Via the DIP switch. 2. 220K 330K 470K Output Current ¢J, 100% of the rated current (corresponds to the setting current level) ¢ , output current begin to reduce, details please refer to the curve. J < 70¢J, 100% of the rated current (corresponds to the setting current level) > 70¢J, output current begin to reduce, details please refer to the curve. < 80¢J, 100% of the rated current (corresponds to the setting current level) > 80¢J, output current begin to reduce, details please refer to the curve. < 60 > 60 eli NTC resistance Pr Notes: 1. MW does not offer the NTC resistor and all the data above are measured by using THINKING TTC03 series. 2. If other brands of NTC resistor is applied,please check the temperature curve first. File Name:LCM-40-SPEC 2012-09-11