ECO-PACTM 1 Rectifier Module for Power Factor Correction PSBI 9/06 IFAV25 VRRM IC25 VCES Preliminary Data Sheet = 15A = 1200 V = 37A = 600 V Fast Single Phase Rectifier Ultra Fast Boost Chopper Typical Rectified Mains Power Pn = 900 W at Vn = 110 V Pn = 2100 W at Vn = 240 V at VDC = 400 V, fT = 75 kHz, TC = 80°C Input Rectifier Bridge Symbol Features Test Conditions Maximum Ratings 1200 15 10 75 VRRM IFAV25 IFAV80 IFSM TC = 25°C; TC = 80°C; TVJ = 25°C Symbol Test Conditions IR VR = VRRM, TVJ = 25°C TVJ = 125°C 0.5 VF IF = 10A, TVJ = 25°C TVJ = 125°C 1.4 1.6 trr VR = 100 V, IF = 10 A 180° sine 180° sine t = 10 ms (50 Hz), sine V A A A Characteristic Value typ. max. 0.05 1.8 mA mA V V µs 1 -di/dt = 5 A/µs RthJC RthJS per diode with heat transfer paste 2.5 tbd K/W K/W Chopper T Symbol Test Conditions VCES VGES IC25 IC80 RBSOA TVJ = 25°C to 150°C continous Maximum Ratings tSC VCE = 600 V, RG = 10 Ω, VGE = ±15 V TC = 25°C; TC = 80°C; VCE = 600 V, RG = 10 Ω, TVJ = 125°C Clamped inductive load, L= 100 µH TVJ = 125°C, non-repetitive POWERSEM GmbH, Walpersdorfer Str. 53 91126 D- Schwabach Phone: 09122 - 9764-0 Fax.: 09122 - 9764-20 600 ±20 37 25 V V ICM = 100 VCEK ≤VCES A 10 µs A A • Package with DCB ceramic base plate and soldering pins for PCB mounting • Isolation voltage over 3000 V∼ • Planar glasspassivated chips • high level of integrationonly one power semiconductor module required for the whole PFC rectifier • standard PFC control ICs usable • fast rectifier diodes for enhanced EMC behaviour • NPT IGBT with low saturation voltage, ultra fast switching capability, high RBSOA and short circuit ruggedness • internally series connected HiPerFRED free wheeling diode For fast and soft reverse recovery at high switching frequency • leads suitable for PC board soldering • UL registered, E 148688 Applications • single phase rectification with power factor correction (PFC) • low harmonic content of mains current • mains current and voltage in phase • wide input voltage range, controlled output voltage 2005 POWERSEM reserves the right to change limits, test conditions and dimensions PSBI 9/06 Test Conditions ICES VCE = VCES, VGE = 0 V, Characteristic Value typ. IGES VCE(sat) VCE = 0 V, VGE = ±20 V IC = 10A, VGE = 15 V VGE(th) td(on) tr td(off) tf Eon Eoff Cies QGon RthJC RthJS IC = 1mA, VGE = VCE TVJ = 25°C TVJ = 125°C TVJ = 25°C TVJ = 125°C 1 1.5 1.6 min. 3 Inductive load, TVJ = 125°C VCE = 400 V, IC = 10A RG = 10 Ω, VGE = ±15 V VCE = 25 V, VGE = 0 V, f= 1 MHz VCE = 480 V, VGE = 15 V, IC = 10A max. 0.04 100 1.8 nA V V 5 V 30 50 320 ns ns ns 70 0.60 0.31 ns mJ mJ 1600 140 pF nC 0.96 with heat transfer paste mA mA tbd Package style and outline Dimensions in mm (1mm = 0.0394“) +0,3 -0,3 Symbol K/W K/W Chopper D Symbol Test Conditions VRRM IF25 IF80 TC = 25°C; TC = 80°C; Symbol Test Conditions Maximum Ratings 600 35 22 180° sine 180° sine Characteristic Value typ. VR = VRRM, TVJ = 25°C TVJ = 125°C 0.1 VF IF = 10A, 2.2 IRM trr RthJC RthJS IF = 10A, -diF/dt = 400 A/µs, TVJ = 125°C VR = 400 V IR TVJ = 25°C TVJ = 125°C max. 0.1 3.2 2.4 tbd tbd mA mA V V A 1.15 with heat transfer paste V A A tbd µs K/W K/W Module Symbol Test Conditions TVJ Tstg VISOL MD IISOL ≤ 1 mA, 50/60 Hz, t= 1 min Mounting torque (M4) Symbol Test Conditions Maximum Ratings -40...+150 -40...+125 °C °C 3000 1.5-1.8 V~ Nm Characteristic Value typ. dS, dA Weight pin to heatsink POWERSEM GmbH, Walpersdorfer Str. 53 91126 D- Schwabach Phone: 09122 - 9764-0 Fax.: 09122 - 9764-20 16 min. 11.2 mm g 2005 POWERSEM reserves the right to change limits, test conditions and dimensions