ECO-PACTM 1 Rectifier Module PSBI 30/06 for Power Factor Correction -4 H N 5 Preliminary Data Sheet ~1 -G ~A +3 +D Symbol Test Conditions VCES VGES IC25 IC80 RBSOA TVJ = 25 °C to 150 °C 600 V continuous ±20 V TC = 25 °C 42 A Maximum Ratings TS = 80 °C 29 A VCE = 600 V, RG = 10 Ω, TVJ = 125 °C ICM = 100 A clamped inductive load, L = 100 µH VCEK≤VCES VCE = 600 V, VGE = ±15 V, RG = 10 Ω, 10 Test Conditions µs Characteristic Values TVJ = 25 °C, unless otherwise specified VCE(sat) VCE(sat) VCE(sat) VGE(th) VGE(th) ICES ICES IGES td(on) tr td(off) tf Eon Eoff Cies QGon RthJC RthJH VGE = 15 V, IC = 30 A, TVJ = 25 °C max. 2.9 V VGE = 15 V, IC = 30 A, TVJ = 25 °C typ. 2.4 V TVJ = 125 °C typ. 2.9 V VGE = VCE, IC = 0.3 mA min. 3 V VGE = VCE, IC = 0.3 mA max. 5 V VCE = VCES, VGE = 0 V, TVJ = 25 °C max. 0.04 mA 1 mA 100 nA typ. 30 ns typ. 50 ns typ. 270 ns typ. 70 ns typ. 0.78 mJ typ. 0.55 mJ typ. 1500 pF TVJ = 125 °C typ. VCE = 0 V, VGE = ±20 V } Module Symbol TVJ TJM Tstg Visol Md Weight inductive load, TVJ = 125 °C VCE = 400 V, IC = 10 A VGE = ±15 V, RG = 10 Ω VCE = 25 V, f = 1 MHz, VGE = 0 V max. VCE = 480 V, IC = 30 A, VGE = 15 V typ. Test Conditions 140 nC max. 0.96 K/W max. tbd K/W -40...+150 °C 150 °C -40...+150 °C t = 1 min 3000 V∼ Iisol ≤ 1 mA t=1s 3600 V∼ 1.5-1.8 Nm 18 g typ. Package with DCB ceramic base plate and soldering pins for PCB mounting • Isolation voltage over 3000 V∼ • Planar glasspassivated chips • NPT IGBT with low saturation • voltage, ultra fast switching capability, high RBSOA and short circuit ruggedness leads suitable for PC board soldering • UL registered, E 148688 Applications • • • • single phase rectification with power factor correction (PFC) low harmonic content of mains current mains current and voltage in phase wide input voltage range, controlled output voltage Maximum Ratings 50/60 Hz Mounting torque (M 4) Features • TVJ = 125 °C, non-repetitive Symbol = 42 A = 600 V = 42 A = 1400 V 7 IGBT tSC IC25 VCES IF25 VRRM Caution: These devices are sensitive to electrostatic discharge. Users should observe proper ESD handling precautions. Data according to IEC 60747 refer to a single diode unless otherwise stated 2005 POWERSEM reserves the right to change limits, test conditions and dimensions POWERSEM GmbH, Walpersdorfer Str. 53 D - 91126 Schwabach Phone: 09122 - 9764 - 0 FAX: 09122 - 9764 - 20 ECO-PACTM 1 Rectifier Diodes Package style and outline Symbol Test Conditions IF25 IF80 IFSM TC = 25 °C ∫ i2 dt Maximum Ratings 42 TC = 80 °C A 27 A TVJ = 45 °C t = 10 ms (50 Hz), sine 300 A VR = 0 t = 8.3 ms (60 Hz), sine 320 A TVJ = TVJM t = 10 ms (50 Hz), sine 260 A VR = 0 t = 8.3 ms (60 Hz), sine 280 A TVJ = 45 °C t = 10 ms (50 Hz), sine 450 A²s VR = 0 t = 8.3 ms (60 Hz), sine 425 A²s TVJ = TVJM t = 10 ms (50 Hz), sine 340 A²s VR = 0 t = 8.3 ms (60 Hz), sine 325 A²s Symbol Test Conditions IR VR = VRRM, TVJ = TVJM ≤ VR = VRRM, TVJ = 25°C VF VTO rT RthJC RthJK ds dA a IF = 50 A, under development Characteristic Value TVJ = 25 °C For power-loss calculations only 3.0 mA ≤ 0.5 mA ≤ 1.55 V 0.85 V 13 mΩ per diode; DC per diode; DC 2.9 3.2 K/W K/W Creeping distance on surface Creeping distance in air Max. allowable acceleration 11.2 9.7 50 mm mm m/s² 2005 POWERSEM reserves the right to change limits, test conditions and dimensions POWERSEM GmbH, Walpersdorfer Str. 53 D - 91126 Schwabach Phone: 09122 - 9764 - 0 FAX: 09122 - 9764 - 20