ECO-PACTM 2 Rectifier Module PSBI 33/06 for Power Factor Correction X Fast Single Phase Rectifier Ultra Fast Boost Chopper KE V P S MA Preliminary Data Sheet 1 IGBT NTC optional Test Conditions VCES VGES IC25 IC80 RBSOA TVJ = 25 °C to 150 °C 600 V continuous ±20 V TC = 25 °C 44 A Maximum Ratings TS = 80 °C 30 A VCE = 600 V, RG = 10 Ω, TVJ = 125 °C ICM = 100 A clamped inductive load, L = 100 µH VCEK≤VCES VCE = 600 V, VGE = ±15 V, RG = 10 Ω, 10 Test Conditions Characteristic Values VCE(sat) VCE(sat) VCE(sat) VGE(th) VGE(th) ICES ICES IGES td(on) tr td(off) tf Eon Eoff Cies QGon RthJC RthJH VGE = 15 V, IC = 10 A, TVJ = 25 °C max. 1.8 V VGE = 15 V, IC = 10 A, TVJ = 25 °C typ. 1.5 V TVJ = 125 °C typ. TVJ = 25 °C, unless otherwise specified 1.6 V VGE = VCE, IC = 1 mA min. 3 V VGE = VCE, IC = 1 mA max. 5 V VCE = VCES, VGE = 0 V, TVJ = 25 °C max. 0.04 mA 1 mA max. 100 nA typ. 31 ns typ. 50 ns typ. 291 ns typ. 70 ns typ. 0.60 mJ typ. 0.31 mJ typ. 1600 pF VCE = 480 V, IC = 10 A, VGE = 15 V typ. 140 nC max. 0.96 K/W max. tbd K/W VCE = 0 V, VGE = ±20 V } Symbol TVJ TJM Tstg Visol Md Weight inductive load, TVJ = 125 °C VCE = 400 V, IC = 10 A VGE = ±15 V, RG = 10 Ω VCE = 25 V, f = 1 MHz, VGE = 0 V Test Conditions Maximum Ratings -40...+150 °C 150 °C -40...+150 °C 50/60 Hz t = 1 min 3000 V∼ Iisol ≤ 1 mA t=1s 3600 V∼ 1.5-2.0 Nm 24 g Mounting torque (M 4) typ. Features µs Symbol TVJ = 125 °C typ. for exact pin configuration see final development • TVJ = 125 °C, non-repetitive Module = 44 A = 600 V = 15 A = 1200 V 3 Symbol tSC IC25 VCES IFAV25 VRRM • • • • • • • • Package with DCB ceramic base plate and soldering pins for PCB mounting Isolation voltage over 3000 V∼ Planar glasspassivated chips high level of integrationonly one power semiconductor module required for the whole PFC rectifier standard PFC control ICs usable fast rectifier diodes for enhanced EMC behaviour NPT IGBT with low saturation voltage, ultra fast switching capability, high RBSOA and short circuit ruggedness internally series connected HiPerFRED free wheeling diode For fast and soft reverse recovery at high switching frequency leads suitable for PC board soldering • UL registered, E 148688 Applications • • • • single phase rectification with power factor correction (PFC) low harmonic content of mains current mains current and voltage in phase wide input voltage range, controlled output voltage Caution: These Devices are sensitive to electrostatic discharge. Users should observe proper ESD handling precautions. Data according to IEC 60747 refer to a single diode unless otherwise stated 2005 POWERSEM reserves the right to change limits, test conditions and dimensions POWERSEM GmbH, Walpersdorfer Str. 53 D - 91126 Schwabach Phone: 09122 - 9764 - 0 FAX: 09122 - 9764 - 20 ECO-PACTM 2 Fast Recovery Diode Symbol Test Conditions VRRM IF25 IF80 TVJ = 25 °C to 150 °C Symbol Test Conditions Maximum Ratings 600 V TC = 25 °C 30 A TC = 80 °C 19 A Package style and outline under development Characteristic Values TVJ = 25 °C, unless otherwise specified VF IF = 10 A, TVJ = 25 °C max. 3.2 V TVJ = 25 °C typ. 2.2 V TVJ = 125 °C max. 2.4 V TVJ = 25 °C max. 0.1 mA TVJ = 125 °C typ. IR VR = VRRM, 0.1 mA IRM trr RthJC RthJH IF = 10 A, diF/dt = -400 A/µs, TVJ = 125 °C tbd A VR = 400 V tbd ns 1.15 K/W tbd K/W max. with heat transfer paste Rectifier Diodes Symbol VRRM IFAV25 IFAV80 IFSM Symbol Test Conditions Maximum Ratings 1200 V TC = 25 °C, sine 180 ° 33 A TC = 80 °C, sine 180 ° 22 A TVJ = 25 °C, 60 A T = 10 ms (50Hz) Test Conditions Characteristic Values TVJ = 25 °C, unless otherwise specified VF IF = 10 A, TVJ = 25 °C max. 1.8 V TVJ = 25 °C typ. 1.4 V TVJ = 125 °C typ. 1.6 V TVJ = 25 °C max. 0.05 mA TVJ = 125 °C IR VR = VRRM, typ. 0.5 mA trr RthJC RthJH VR = 100 V, IF = 10 A, -di/dt = 5 A/µs typ. 1 µs 2.5 K/W tbd K/W per diode with heat transfer paste max. Module Symbol Test Conditions ds dA a R25 Creeping distance on surface Creeping distance in air Max. allowable acceleration NTC @ 25 °C Characteristic Values 11.2 5 50 5.000 mm mm m/s² Ω 2005 POWERSEM reserves the right to change limits, test conditions and dimensions POWERSEM GmbH, Walpersdorfer Str. 53 D - 91126 Schwabach Phone: 09122 - 9764 - 0 FAX: 09122 - 9764 - 20