SF2006C • SAW Filter for W-CDMA • 5.0 X 5.0 X 1.7 mm Surface-Mount Case • Complies with Directive 2002/95/EC (RoHS) 190.00 MHz SAW Filter Pb Maximum Rating Rating Value Units 10 dBm Operating Temperature Range -30 to +70 °C Storage Temperature Range in Tape and Reel -30 to +70 °C Input Power Level SM5050-8 Electrical Characteristics Characteristic Sym Center Frequency fC 190 ILMIN 8.0 Insertion Loss 6 dB Bandwidth BW Notes Min 4.8 Typ Max Units MHz 10 5.73 dB MHz Group Delay Ripple 70 150 ns RMS Phase Linearity, fC ± 2 MHz 6 8 deg Attenuation Referended to ILMIN: 170 to 180 MHz, or (fC - 20 MHz) to (fC - 10 MHz) 27 34 180 to 185.5 MHz, or (fC -10 MHz) to (fC -4.5 MHz) 25 31 194.5 to 200 MHz, or (fC + 4.5 MHz) to (fC + 10 MHz) 25 30 200 to 210 MHz, or (fC + 10 MHz) to (fC + 20 MHz) 27 33 Ultimate Rejection dB 50 Lid Symbolization (Y=year, WW=week, S=shift) RFM 734 YWWS Electrical Connections Connection Terminals Port 1 Input Port 2 Output 2 6 Ground All others Dot indicates Pin 1 CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." www.RFM.com E-mail: [email protected] ©2008-2010 by RF Monolithics, Inc. 5. 6. 7. 8. The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. Page 1 of 4 SF2006C - 6/14/10 www.RFM.com E-mail: [email protected] ©2008-2010 by RF Monolithics, Inc. Page 2 of 4 SF2006C - 6/14/10 SM5050-8 Surface-Mount 8-Terminal Ceramic Case 5.0 X 5.0 mm Nominal Footprint Case Dimensions Dimension A B C D E F G H I J K L M N O P Q L J M Min 4.80 4.80 1.30 1.98 1.07 0.50 2.39 P H mm Nom 5.00 5.00 1.50 2.08 1.17 0.64 2.54 1.27 0.76 1.55 2.79 0.76 2.36 1.55 2.79 2.79 2.79 Max 5.20 5.20 1.70 2.18 1.27 0.70 2.69 Min 0.189 0.189 0.050 0.078 0.042 0.020 0.094 Inches Nom 0.197 0.197 0.060 0.082 0.046 0.025 0.100 0.050 0.030 0.061 0.110 0.030 0.093 0.061 0.110 0.110 0.110 Max 0.205 0.205 0.067 0.086 0.050 0.028 0.106 Case Materials I Materials Q N K O Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free PCB Footprint TOP VIEW BOTTOM VIEW A E C B 8 8 1 7 D 7 1 2 6 6 2 3 5 5 3 4 G 4 F www.RFM.com E-mail: [email protected] ©2008-2010 by RF Monolithics, Inc. Page 3 of 4 SF2006C - 6/14/10 Tape and Reel Specifications "B" REF. 100 REF. “B” Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 5.3 mm 5.3 mm 2.0 mm 8.0 mm 12.0 mm PIN #1 USER DIRECTION OF FEED www.RFM.com E-mail: [email protected] ©2008-2010 by RF Monolithics, Inc. Page 4 of 4 SF2006C - 6/14/10