H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 1/26 Revision 1.0 HannStar Product Specification (Formal) Model: HSD101PFW2 -A** Note: (1) Please contact HannStar Display Corp. before designing your product based on this module specification. (2) The information contained herein is presented merely to indicate the characteristics and performance of our products. No responsibility is assumed by HannStar for any intellectual property claims or other problems that may result from application based on the module described herein. (3) The mark “ ** ” of Model means sub-model code. The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 2/26 Revision 1.0 Record of Revisions Rev. Date Sub-Model 1.0 -- A** Description of change Formal Product Specification was first released. The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 3/26 Revision 1.0 Contents 1.0 General description ………………………………… p.4 2.0 Absolute maximum ratings……………………………. p.5 3.0 Optical characteristics.………………………………. p.6 4.0 Block diagram p.10 5.0 Interface pin connection …………………………… p.12 6.0 Electrical characteristics …………………………… p.13 7.0 Reliability test items ………………………………… p.20 8.0 Outline dimension …………………………………… p.21 9.0 Lot mark ……………………………………………... p.23 10.0 Package specification ……………………………… p.24 11.0 General precaution …………………………………… p.25 For specific customer revision (Quanta Only) …………….. p.28 HSD101PFW2-A01…………………………………………… p29 For specific customer revision (Samsung Only) …………… p.32 ……………………………………… For specific customer revision (LGD Only)…………………. P.33 The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 4/26 Revision 1.0 1.0 GENERAL DESCRIPTION 1.1 Introduction HannStar Display model HSD101PFW2-A is a color active matrix thin film transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT LCD panel, a driving circuit and a back light system. This TFT LCD has a 10.1 (16:9) inch diagonally measured active display area with WSVGA (1024 horizontal by 600 vertical pixel) resolution. 1.2 Features ■ 10.1 (16:9 diagonal) inch configuration ■ One channel LVDS interface ■ 262K color by 6 bit R.G.B signal input ■ RoHS Compliance ■ Halogen Free 1.3 Applications Mobile NB Digital Photo frame Display terminal for AV application 1.4 General information Item Specification Unit Outline Dimension 235 x 143 x 4.9 (Typ.) mm Display area 222.72(H) x 125.28(V) mm Number of Pixel 1024 RGB (H) x 600(V) pixels Pixel pitch 0.2175(H) x 0.2088(V) mm Pixel arrangement RGB Vertical stripe Display mode Normally white NTSC 50 Surface treatment Glare, Hard-Coating (3H) Weight 180 (Typ.) Back-light White LED Power Consumption 0.65W (Max.)/Logic % g W The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 5/26 Revision 1.0 1.5 Mechanical Information Module Size Item Horizontal (H) Min. 234.5 Typ. 235 Max. 235.5 Unit mm Vertical (V) 142.5 143 143.5 mm 4.9 180 5.2 mm 190 g Depth (D) Weight - - 2.0 ABSOLUTE MAXIMUM RATINGS 2.1 Electrical Absolute Rating 2.1.1 TFT LCD Module Item Symbol Logic Supply voltage VDD Environment Absolute Rating Item Symbol Operating Temperature Topa Storage Temperature Tstg Min. -0.3 Max. 4.0 Unit V Note Min. 0 -20 Max. 50 60 Unit Note 2.1.2 ℃ ℃ The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 6/26 Revision 1.0 3.0 OPTICAL CHARACTERISTICS 3.1 Optical specification Item Symbol Condition Contrast CR Red Color chromaticity (CIE1931) Green Blue White Hor. Ver. 400 500 - 4 8 12 24 YL 160 200 - 0.542 0.592 0.642 0.305 0.355 0.405 0.277 0.327 0.377 GY 0.505 0.555 0.605 Bx 0.104 0.154 0.204 BY 0.044 0.094 0.144 Wx 0.263 0.313 0.363 Wy 0.279 0.329 0.379 40 45 40 45 U 10 15 D 30 35 80 70 Θ=0 Rx Normal viewing angle RY Gx Θ Θ Θ Θ L Brightness uniformity BUNI Brightness Uniformity BUNI 3.2 Max. Tf R Viewing angle Typ. - - Tr Response time White luminance (5 point) Min. CR>10 Θ=0 (5point) =0 Θ (13 points) Unit Note (1)(2)(4) msec cd/m2 (1)(3) (1)(4)(5) (IL=18mA) - - - - - - % (5) - - % (6) (1)(4) Measuring Condition ■ Measuring surrounding dark room ■ Ambient temperature 25±2oC ■ 15min. warm-up time. : : The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. 3.3 Page No. 7/26 Revision 1.0 Measuring Equipment ■ FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity and BM-5A for other optical characteristics. ■ Measuring spot size 20 ~ 21 mm Note (1) Definition of Viewing Angle: : ΘU 12’ o’clock Φ=90o ΘL ΘR Φ=180o Φ=0o ΘD 6’ o’clock Φ=270o Note (2) Definition of Contrast Ratio (CR) : measured at the center point of panel Luminance with all pixels white CR = Luminance with all pixels black The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Page No. 8/26 Revision 1.0 Document No. Note (3) Definition of Response Time : Sum of TR and TF white(TFT OFF) black (TFT ON) TR white(TFT OFF) TF 100% 90% Optical response 10% 0% time Note (4) Definition of optical measurement setup The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 9/26 Revision 1.0 Note (5) Definition of Average Luminance Uniformity of White (5 Point) Y1+Y2+Y3+Y4+Y5 Average Luminance Uniformity = 5 Note (6) Definition of brightness uniformity (Min Luminance of 5 points) Luminance uniformity(5 points) = (Max Luminance of 5 points) (Min Luminance of 13 points) Luminance uniformity(13points) = (Max Luminance of 13 points) ×100% ×100% The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 10/26 Revision 1.0 4.0 BLOCK DIAGRAM 4.1 TFT LCD Module: LED B/L X-driver IC Connector LED Driver Timing Y-driver IC Controller EDID + LVDS DC/DC Receiver Liquid Crystal Panel 1024x600 pixels Converter Gray scale Manipulation Voltage Generation Circuit 4.2 Pixel Format 1,1 1,2 1,3 1,1024 1,4 2,1 LCD Display Area 1 Pixel 600 Lines R 600,1 G B R R 600, 1024 1024 pixel (3072 Dots) The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 11/26 Revision 1.0 4.3 Relationship Between Displayed Color and Input Basic color Display Black Blue Green Light Blue Red Purple Yellow White Black Gray scale of Red Dark ↑ ↓ Light Red Black Gray scale of Green Gray scale of White & Black H H H L L L H H H L L L H H H L L L L L L L L L L L L L L L L H H L L L H L H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H H H L L L H H H L L L H H H H H H L L L L L L H H H L L L L L L L L H LL LL LL LL HL LL L L L L L L L L L L L L L L L L L L L L L L L H L L L L H L L L L L L L L L L L L L H H H L L L L L L L L L L H H L L L HL LL HL LL LL LL L L L L L L L H H HH LH HH H H H H H H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H LH LH LH LL HL LL H H H L L L L L L L L L H H H L L L L L L L L H L L61 L L62 L Green L63 L L0 H L1 L L2 L3…L60 H H H L L L L H H L L H : : H H H L H H HH LH HH H H H H H H L61 L62 Red L63 L0 L1 L2 L3…L60 : : : : H H H L3…L60 : : : : : : H H H : : : : : : L L L L L L LSB MSB LSB Gray scale G2G1 G0 B5 B4 B3 B2 B1 B0 level L L LL L L L L L L L LH H H H H H H H HL L L L L L H H HH H H H H H L L LL L L L L L L L LH H H H H H H H HL L L L L L H H HH H H H H H L L LL L L L L L L0 L L LL L L L L L L1 L L LL L L L L L L2 : : H H H L L L L L L L L L Dark ↑ ↓ Light White G3 L L H H L L H H L L L : : Dark ↑ ↓ Light Blue Black MSB G5 G4 L L L L H H H H L L L L H H H H L L L L L L : : Dark ↑ ↓ Light Green Black Gray scale of Blue MSB LSB R5 R4 R3 R2 R1 R0 L L L L L L L L L L L L L L L L L L L L L L L L H H H H H H H H H H H H H H H H H H H H H H H H L L L L L L L L L L L H L L L L H L H L H L H L L61 L62 Blue L63 L0 L1 L2 L3…L60 H H H L H H H L61 L L62 H White L63 The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 12/26 Revision 1.0 5.0 INTERFACE PIN CONNECTION 4.1 : TFT LCD Module CN1 (Input signal): IPEX 20455-040E-12 (IPEX or equivalent) Pin No. Signal Description 1 NC No Connection 2 VCC 3.3V Power Supply 3 VCC 3.3V Power Supply 4 V_EDID EDID 3.3V Power Supply 5 NC No Connection 6 CLK_EDID EDID Clock 7 DATA_EDID EDID Data 8 RXIN0LVDS Signal - channel09 RXIN0+ LVDS Signal+ channel0+ 10 GND Ground 11 RXIN1Data Input channel112 RXIN1+ Data Input channel1+ 13 GND Ground 14 RXIN2Data Input channel215 RXIN2+ Data Input channel2+ 16 GND Ground 17 RXCLKIN- Data Input CLK18 RXCLKIN+ Data Input CLK+ 19 GND Ground 20 NC No Connection 21 NC No Connection 22 GND Ground 23 NC No Connection 24 NC No Connection 25 GND Ground 26 NC No Connection 27 NC No Connection 28 GND Ground 29 NC No Connection 30 NC No Connection 31 VLED_GND LED Ground 32 VLED_GND LED Ground 33 VLED_GND LED Ground 34 NC No Connection 35 PWM PWM Signal for LED dimming control 36 LED_EN LED Enable Pin (+3V Input) 37 NC No Connection 38 VLED LED Power Supply 5-21V 39 VLED LED Power Supply 5-21V 40 VLED LED Power Supply 5-21V Note The brightness of LCD panel could be changed by adjusting PWM : The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 13/26 Revision 1.0 6.0 ELECTRICAL CHARACTERISTICS 6.1 TFT LCD Module Item Symbol Supply Voltage VDD Min. 3.0 Typ. 3.3 Max. 3.6 Unit V Current of power supply IDD - 0.192 - A Inrush current IRUSH - - 1.50 A Note Note (1) VDD =3.3V L0 pattern Ta=25 fv=60Hz Note (2) 、 ℃ Note (1): VDD-dip condition: When VDD operating within 2.7V VDD<3.0V td 10ms , the display may momentarily become abnormal. ≦ , ≦ VDD<2.7V , VDD dip condition should also follow the Power On/Off conditions for supply voltage. VDD 2.7v 3.0v GND td The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Note Page No. 14/26 Revision 1.0 :(2) Power on Inrush current test circuit VDD 0.9VDD 0.1VDD 0V 0.5 ms Vin rising time The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. 6.2 Switching Characteristics for LVDS Receiver Typ. Item Symbol Min. Differential Input High Threshold Vth - Differential Input Low Threshold Vtl -100 Input Current Differential input Voltage IIN |VID| -10 Common Mode Voltage Offset VCM - - - - Page No. 15/26 Revision 1.0 Max. Unit 100 mV - 0.1 (|VID|/2) 1.25 mV +10 uA 0.6 V 2.4-(|VID|/2) V Conditions VCM=1.2V 6.3 Bit Mapping & Interface Definition 7T 6.5/7T 5.5/7T 4.5/7T 3.5/7T 2.5/7T 1.5/7T 0.5/7T RCLK Rin0 R[2] Rin1 G[3] Rin2 B[4] R[1] G[2] B[3] R[0] G[0] R[5] R[4] R[3] R[2] R[1] R[0] G[0] G[1] B[1] B[0] G[5] G[4] G[3] G[2] G[1] B[1] B[2] DE (VS) (HS) B[5] B[4] B[3] B[2] DE Pervious cycle Current cycle Next cycle LVDS Receiver Input Timing Definition for 6bits LVDS input The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 16/26 Revision 1.0 6.4 Interface Timing (DE mode) Item Frame Rate Frame Period Vertical Display Time Vertical Blanking Time 1 Line Scanning Time Horizontal Display Time Horizontal Blanking Time Clock Rate Symbol -t1 t2 t3 t4 t5 t6 t7 Min. 55 612 600 12 1160 1024 136 39 Typ. 60 625 600 25 1200 1024 176 45 Max. 65 638 600 38 1240 1024 216 51.42 Unit Hz line line line clock clock clock MHz Timing Diagram of Interface Signal (DE mode) The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 17/26 Revision 1.0 6.5 Power On / Off Sequence Power Off Power On Power Supply 0.9VDD 0.9VDD 0.1VDD 0.1VDD 0V 0.1VDD TP1 TP3 TP2 Signal TP4 0.6V 0.6V 0V Backlight (Recommended) Item TP1 TP2 TP3 TP4 TP5 TP6 TP5 TP6 50% 50% Min. 0.5 0 0 500 200 200 Typ. ------- Max. 10 50 50 ---- Unit msec msec msec msec msec msec Remark : Note (1) The supply voltage of the external system for the module input should be the same as the definition of VDD. (2) Apply the lamp volatge within the LCD operation range. When the back-light turns on before the LCD operation or the LCD truns off before the back-light turns off, the display may momentarily become white. (3) In case of VDD = off level, please keep the level of input signal on the low or keep a high impedance. (4) TP4 should be measured after the module has been fully discharged between power off and on period. (5) Interface signal shall not be kept at high impedance when the power is on. The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Page No. 18/26 Revision 1.0 Document No. 6.6 Backlight Unit Symbol Min Typ Max Units LED Current IF -- 18.0 18.75 mA LED Voltage VF 3.0 3.2 3.4 Volt LED Power consumption PLED -- 1.38 1.53 Watt LED Life-Time N/A Parameter Condition ℃ Ta=25℃ Ta=25℃ Ta=25 Note (1) 10,000 -- -- ℃ Hour Ta=25 IF=18mA Note (2) Note (1): Calculator value for reference P=IF x VF x N (LED Qty’) Note (2): The LED lifetime defines as the estimated time to 50% degradation of final luminous. 6.7 LED Driver 6.7.1 Absolute Maximum Ratings Item Symbol LED Power Supply voltage VLED LED_EN, PWM pin Voltage VEN, VPWM 6.7.2 Min. -0.3 -- Max. 24 5.5 Unit Volt Volt Note DC Electrical Characteristics Parameter Symbol Min Typ Max Units LED Power Supply Voltage VLED 5.0 -- 21.0 Volt LED_EN High Threshold VENH 2.0 -- -- Volt LED_EN Low Threshold VENL -- -- 0.3 Volt PWM High Threshold VPWMH 3.0 -- -- Volt PWM Low Threshold VPWML -- -- 0.2 Volt PWM Frequency FPWM 200 -- 300 Hz PWM Duty Cycle TD 10 -- -- % Remark Note(1) The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Page No. 19/26 Revision 1.0 Document No. Note: PWM Duty Cycle. Pulse duty the bigger the brighter. T Duty Cycle TD= (t / T) x 100% t 6.7.3 LED Power on/off sequence T1 T2 T3 T4 T5 LED Power Supply, VLED 0.9VLED 0.9VLED 0V 0.1VLED 0.1VLED Dimming Signal, PWM 0V LED Enable, LED_EN 0V Symbol Value Min Typ Max T1 10 -- -- T2 10 -- -- T3 50 -- -- T4 0 -- -- T5 10 -- -- Unit ms Note: The duty of LED dimming signal should be more than 20% in T2 and T3 The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 20/26 Revision 1.0 7.0 Reliability test items No. Item 1 High Temperature Storage 2 Low Temperature Storage High Temperature Operation 3 Low Temperature Operation 4 5 Thermal Cycling Test (non operation) Vibration 6 7 Shock Conditions Ta=+60 C, 240hrs Ta=-20oC, 240hrs Ta=+50oC, 500hrs Ta=0oC, 500hrs -20oC(30min)→+60oC(30min),100 cycles Remark o Sine Wave 1.5G, 5~500Hz, XYZ 30min/each direction Half-Sine, 200G, 2ms, ±XYZ, 1time Storage / Operating temperature Humidity (%) 100 90 80 60 Operating Range 40 Storage Range 20 10 0 -40 -20 0 20 Temperature (oC) 40 50 60 Note .Max wet bulb temp.=39oC The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. 8.0 Page No. 21/26 Revision 1.0 OUTLINE DIMENSION 8.1 Front View Outline Dimension (2009/7/10 update) Suggestion screw spec.-- 2* BM Assembly Tolerance | A-A’ | ≤ 1 (mm) | B-B’ | ≤ 1 (mm) The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 22/26 Revision 1.0 8.2 Back View Outline Dimension (2009/10/16 update) LGD Label The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. 9.0 Page No. 23/26 Revision 1.0 LOT MARK 9.1 Lot Mark 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Code 1,2,3,4,5,6: HannStar internal flow control code. Code 7: production location. Code 8: production year. Code 9: production month. Code 10,11,12,13,14,15: serial number. Note (1) Production Year Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 Mark 1 2 3 4 5 6 7 8 9 0 Note (2) Production Month Month Jan. Mark 1 Feb. Mar. 2 3 Apr. 4 May. Jun. 5 6 Jul. 7 Aug. Sep. 8 9 Oct A Nov. Dec. B C 9.2 Location of Lot Mark (1) Location : The label is attached to the backside of the LCD module. See Product back view. ( Section 8.0 : OUTLINE DIMENSION ) (2) Detail of the Mark : As attached below (3) This is subject to change without prior notice. HSD101PFW2 Rev: * -A EDX.X 6 A0 The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 24/26 Revision 1.0 10.0 PACKAGE SPECIFICATION 10.1 Packing form LCM Model LCM Qty. in the box Inner Box Size (mm) HSD101PFW2-A 50 pcs/box 460 x 316 x 321H Notice 10.2 Packing assembly drawings HSD101PFW1-A Material Notice Box Corrugated Paper Board Partition/Pad Corrugated Paper Board Corner Pad Corrugated Paper Board (AB Flute) (B Flute) (AB Flute) ESD bag PE -- The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title HSD101PFW2-A Formal Specification Document No. Page No. 25/26 Revision 1.0 11.0 GENERAL PRECAUTION 11.1 Use Restriction This product is not authorized for use in life supporting systems, aircraft navigation control systems, military systems and any other application where performance failure could be life-threatening or otherwise catastrophic. 11.2 Disassembling or Modification Do not disassemble or modify the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. HannStar does not warrant the module, if customers disassemble or modify the module. 11.3 Breakage of LCD Panel 11.3.1.If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid crystal, and do not contact liquid crystal with skin. 11.3.2. If liquid crystal contacts mouth or eyes, rinse out with water immediately. 11.3.3. If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 11.3.4. Handle carefully with chips of glass that may cause injury, when the glass is broken. 11.4 Electric Shock 11.4.1. Disconnect power supply before handling LCD module. 11.4.2. Do not pull or fold the LED cable. 11.4.3. Do not touch the parts inside LCD modules and the fluorescent LED’s connector or cables in order to prevent electric shock. 11.5 Absolute Maximum Ratings and Power Protection Circuit 11.5.1. Do not exceed the absolute maximum rating values, such as the supply voltage variation, input voltage variation, variation in parts’ parameters, environmental temperature, etc., otherwise LCD module may be damaged. 11.5.2. Please do not leave LCD module in the environment of high humidity and high temperature for a long time. 11.5.3. It’s recommended to employ protection circuit for power supply. 11.6 Operation 11.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead. 11.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons handle the LCD module for incoming inspection or assembly. 11.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft material. The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation. H a n n Sta r Di sp l a y C o rp . Document Title Document No. HSD101PFW2-A Formal Specification Page No. 26/26 Revision 1.0 11.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact with polarizer for a long time, they may causes deformation or color fading. 11.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little petroleum benzine or other adequate solvent. 11.7 Mechanism Please mount LCD module by using mounting holes arranged in four corners tightly. 11.8 Static Electricity 11.8.1 Protection film must remove very slowly from the surface of LCD module to prevent from electrostatic occurrence. 11.8.2 Because LCD module use CMOS-IC on circuit board and TFT-LCD panel, it is very weak to electrostatic discharge. Please be careful with electrostatic discharge. Persons who handle the module should be grounded through adequate methods. 11.9 Strong Light Exposure The module shall not be exposed under strong light such as direct sunlight. Otherwise, display characteristics may be changed. 11.10 Disposal When disposing LCD module, obey the local environmental regulations. The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.