AD AD8011-EB

a
300 MHz, 1 mA
Current Feedback Amplifier
AD8011*
FUNCTIONAL BLOCK DIAGRAM
8-Lead Plastic DIP and SOIC
FEATURES
Easy to Use
Low Power
1 mA Power Supply Current (5 mW on +5 VS)
High Speed and Fast Settling on +5 V
300 MHz, –3 dB Bandwidth (G = +1)
180 MHz, –3 dB Bandwidth (G = +2)
2000 V/␮s Slew Rate
29 ns Settling Time to 0.1%
Good Video Specifications (RL = 1 k⍀, G = +2)
Gain Flatness 0.1 dB to 25 MHz
0.02% Differential Gain Error
0.06ⴗ Differential Phase Error
Low Distortion
–70 dBc Worst Harmonic @ 5 MHz
–62 dBc Worst Harmonic @ 20 MHz
Single Supply Operation
Fully Specified for +5 V Supply
8 NC
–IN 2
7
+IN 3
6 OUT
V–
4
AD8011
V+
5 NC
NC = NO CONNECT
amplifier. It also can be used to replace high-speed amplifiers
consuming more power. The AD8011 is a current feedback
amplifier and features gain flatness of 0.1 dB to 25 MHz while
offering differential gain and phase error of 0.02% and 0.06° on
a single +5 V supply. This makes the AD8011 ideal for professional video electronics such as cameras, video switchers or any
high speed portable equipment. Additionally, the AD8011’s
low distortion and fast settling make it ideal for buffering high
speed 8-, 10-, 12-bit A-to-D converters.
APPLICATIONS
Power Sensitive, High Speed Systems
Video Switchers
Distribution Amplifiers
A-to-D Driver
Professional Cameras
CCD Imaging Systems
Ultrasound Equipment (Multichannel)
PRODUCT DESCRIPTION
The AD8011 is a very low power, high-speed amplifier designed
to operate on +5 V or ±5 V supplies. With wide bandwidth, low
distortion and low power, this device is ideal as a general-purpose
The AD8011 offers very low power of 1 mA max and can run
on single +5 V to +12 V supplies. All this is offered in a small
8-lead plastic DIP or 8-lead SOIC package. These features fit
well with portable and battery-powered applications where size
and power are critical.
The AD8011 is available in the industrial temperature range of –
40°C to +85°C.
+5
–40
G = +2
RF = 1k⍀
VS = +5V OR ⴞ5V
VOUT = 200mV p-p
+4
+3
G = +2
3rd
RL = 150⍀
+2
DISTORTION – dBc
NORMALIZED GAIN – dB
NC 1
+1
0
–1
–2
–60
2nd
RL = 150⍀
3rd
RL =1k⍀
–80
–3
2nd
RL = 1k⍀
–4
–5
–100
1
10
FREQUENCY – MHz
100
500
Figure 1. Frequency Response; G = +2, VS = +5 V or ± 5 V
10
20
FREQUENCY – MHz
Figure 2. Distortion vs. Frequency; VS = ± 5 V
*Protected under Patent Number 5,537,079.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
AD8011–SPECIFICATIONS
DUAL SUPPLY (@ T = +25ⴗC, V = ⴞ5 V, G = +2, R = 1 k⍀, R = 1 k⍀, unless otherwise noted)
A
S
F
L
Model
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 1 V p-p
–3 dB Small Signal Bandwidth, VO < 1 V p-p
–3 dB Large Signal Bandwidth, VO = 5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Rise and Fall Time
NOISE/HARMONIC PERFORMANCE
2nd Harmonic
3rd Harmonic
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
Conditions
Min
G = +1
G = +2
G = +10, RF = 500 Ω
G = +2
G = +2, VO = 4 V Step
G = –1, VO = 4 V Step
G = +2, VO = 2 V Step
G = +2, VO = 2 V Step
G = –1, VO = 2 V Step
340
180
20
fC = 5 MHz, VO = 2 V p-p, G = +2
RL = 1 kΩ
RL = 150 Ω
RL = 1 kΩ
RL = 150 Ω
f = 10 kHz
f = 10 kHz, +In
–In
NTSC, G = +2, RL = 1 kΩ
RL = 150 Ω
NTSC, G = +2, RL = 1 kΩ
RL = 150 Ω
DC PERFORMANCE
Input Offset Voltage
AD8011A
Typ
Offset Drift
–Input Bias Current
MHz
MHz
MHz
MHz
V/µs
V/µs
ns
ns
ns
–75
–67
–70
–54
2
5
5
0.02
0.02
0.06
0.3
dB
dB
dB
dB
nV/√Hz
pA/√Hz
pA/√Hz
%
%
Degrees
Degrees
TMIN–TMAX
+Input Bias Current
5
TMIN–TMAX
Open-Loop Transresistance
800
550
TMIN–TMAX
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Offset Voltage
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Resistance
Output Current
Short Circuit Current
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
+Input
+Input
VCM = ± 2.5 V
TMIN–TMAX
5
6
15
20
15
20
1300
± mV
± mV
µV/°C
±µA
±µA
±µA
±µA
kΩ
kΩ
3.8
450
2.3
4.1
kΩ
pF
±V
–52
–57
dB
3.9
4.1
0.1
30
60
15
± 1.5
TMIN–TMAX
Vs = ± 5 V ± 1 V
Units
400
210
57
25
3500
1100
25
0.4
3.7
2
2
10
5
TMIN–TMAX
Max
55
1.0
58
0.3
± 6.0
1.3
±V
Ω
mA
mA
V
mA
dB
Specifications subject to change without notice.
–2–
REV. B
AD8011
SINGLE SUPPLY
(@ TA = +25ⴗC, VS = +5 V, G = +2, RF = 1 k⍀, VCM = 2.5 V, RL = 1 k⍀, unless otherwise noted)
Model
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
–3 dB Large Signal Bandwidth, VO = 2.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Rise and Fall Time
NOISE/HARMONIC PERFORMANCE
2nd Harmonic
3rd Harmonic
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
Conditions
Min
G = +1
G = +2
G = +10, RF = 500 Ω
G = +2
G = +2, VO = 2 V Step
G = –1, VO = 2 V Step
G = +2, VO = 2 V Step
G = +2, VO = 2 V Step
G = –1, VO = 2 V Step
270
150
AD8011A
Typ
15
fC = 5 MHz, VO = 2 V p-p, G = +2
RL = 1 kΩ
RL = 150 Ω
RL = 1 kΩ
RL = 150 Ω
f = 10 kHz
f = 10 kHz, +In
–In
NTSC, G = +2, RL = 1 kΩ
R L = 150 Ω
NTSC, G = +2, RL = 1 kΩ
RL = 150 Ω
DC PERFORMANCE
Input Offset Voltage
Offset Drift
–Input Bias Current
MHz
MHz
MHz
MHz
V/µs
V/µs
ns
ns
ns
–84
–67
–76
–54
2
5
5
0.02
0.6
0.06
0.8
dB
dB
dB
dB
nV/√Hz
pA/√Hz
pA/√Hz
%
%
Degrees
Degrees
TMIN–TMAX
+Input Bias Current
5
TMIN–TMAX
Open-Loop Transresistance
800
550
TMIN–TMAX
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Offset Voltage
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Resistance
Output Current
Short Circuit Current
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
+Input
+Input
VCM = 1.5 V to 3.5 V
TMIN–TMAX
REV. B
mV
mV
µV/°C
±µA
±µA
±µA
±µA
kΩ
kΩ
1.5 to 3.5
kΩ
pF
V
–52
–57
dB
1.2 to 3.8
0.9 to 4.1
0.1
30
50
55
–3–
15
20
15
20
1300
+3
Specifications subject to change without notice.
5
6
450
2.3
1.2 to 3.8
15
TMIN–TMAX
∆Vs = ± 1 V
Units
328
180
57
20
2000
500
29
0.6
4
2
2
10
5
TMIN–TMAX
Max
0.8
58
0.3
+12
1.15
+V
Ω
mA
mA
V
mA
dB
AD8011
ABSOLUTE MAXIMUM RATINGS 1
MAXIMUM POWER DISSIPATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V
Internal Power Dissipation2
Plastic DIP Package (N) . . . . . . . . Observe Derating Curves
Small Outline Package (R) . . . . . . . Observe Derating Curves
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 2.5 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range (N, R) . . . . . . . . –65°C to +125°C
Operating Temperature Range (A Grade) . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
The maximum power that can be safely dissipated by the
AD8011 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic
encapsulated devices is determined by the glass transition temperature of the plastic, approximately +150°C. Exceeding this
limit temporarily may cause a shift in parametric performance
due to a change in the stresses exerted on the die by the package.
Exceeding a junction temperature of +175°C for an extended
period can result in device failure.
While the AD8011 is internally short circuit protected, this
may not be sufficient to guarantee that the maximum junction
temperature is not exceeded under all conditions. To ensure
proper operation, it is necessary to observe the maximum power
derating curves (shown below in Figure 3).
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for device in free air:
8-Lead Plastic DIP Package: θJA = 90°C/W
8-Lead SOIC Package: θJA = 155°C/W
2.0
MAXIMUM POWER DISSIPATION – Watts
TJ = +150ⴗC
8-LEAD PLASTIC DIP PACKAGE
1.5
1.0
8-LEAD SOIC PACKAGE
0.5
0
–50 –40 –30 –20 –10
0
10
20 30
40
50
60
70 80
90
AMBIENT TEMPERATURE – ⴗC
Figure 3. Maximum Power Dissipation vs. Temperature
ORDERING GUIDE
Model
AD8011AN
AD8011AR
AD8011AR-REEL
AD8011AR-REEL7
AD8011-EB
Temperature
Range
Package
Description
Package
Option
– 40°C to +85°C
– 40°C to +85°C
–40°C to +85°C
–40°C to +85°C
8-Lead Plastic DIP
8-Lead SOIC
13" Tape and Reel
7" Tape and Reel
Evaluation Board
N-8
SO-8
SO-8
SO-8
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8011 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. B
AD8011
1k⍀
1k⍀
RL
1k⍀
1k⍀
VOUT
VIN
1k⍀
RL
1k⍀
52.3⍀
VOUT
VIN
50⍀
+VS
0.01␮F
10␮F
0.01␮F
10␮F
+VS
0.01␮F
10␮F
0.01␮F
10␮F
–VS
–VS
Figure 4. Test Circuit; Gain = +2
Figure 7. Test Circuit; Gain = –1
Figure 5.* 100 mV Step Response; G = +2, VS = ±2.5 V or ±5 V
Figure 8.* 100 mV Step Response; G = –1, VS = ±2.5 V or ±5 V
Figure 6.* Step Response; G = +2, VS = ± 2.5 V (2 V
Step) and ± 5 V (4 V Step)
Figure 9.* Step Response; G = –1, VS = ± 2.5 V (2 V
Step) and ± 5 V (4 V Step)
*NOTE: VS = ± 2.5 V operation is identical to V S = +5 V single supply operation.
REV. B
–5–
AD8011
6.5
9
G = +2
VIN = 100mV p-p
RL = 1k⍀
RF = 1k⍀
6.4
6.3
8
ⴞ5V
VS = +5V
7
SWING – V p-p
6.2
VS = ⴞ5V
6.0
5.9
6
5
4
5.8
2
5.7
1
5.6
0
10
5.5
1
10
FREQUENCY – MHz
100
500
Figure 10. Gain Flatness; G = +2
100
1000
LOAD RESISTANCE – Ohms
–40
G = +2
DISTORTION – dBc
2nd
RL = 150⍀
3rd
RL =1k⍀
–80
–60
2nd
RL = 150⍀
–80
3rd
RL =1k⍀
2nd
RL = 1k⍀
2nd
RL =1k⍀
–100
–100
10
1
20
10
RL = 150⍀
RL = 1k⍀
IRE
VS = ⴞ5V
G = +2
100
0.4
0.3
0.2
0.1
0.00
–0.1
–0.2
–0.3
–0.4
RL = 150⍀
RL = 1k⍀
0
IRE
100
1k⍀ DIFF GAIN – %
VS = ⴞ5V
G = +2
0.08
0.06
0.04
0.02
0.00
–0.02
–0.04
–0.06
–0.08
1k⍀ DIFF PHASE – Degrees
Figure 14. Distortion vs. Frequency; VS = +5 V
150⍀ DIFF PHASE – Degrees
1k⍀ DIFF PHASE – Degrees
DIFF GAIN – %
Figure 11. Distortion vs. Frequency; VS = ± 5 V
0
20
FREQUENCY – MHz
FREQUENCY – MHz
0.08
0.06
0.04
0.02
0.00
–0.02
–0.04
–0.06
–0.08
VS = +5V
G = +2
RL=1k⍀
RL=150⍀
0
Figure 12. Diff Phase and Diff Gain; VS = ± 5 V
IRE
RL=150⍀
RL=1k⍀
IRE
0.8
0.6
0.4
0.2
0.0
–0.2
–0.4
–0.6
–0.8
100
VS = +5V
G = +2
0
0.8
0.6
0.4
0.2
0.0
–0.2
–0.4
–0.6
–0.8
150⍀ DIFF GAIN – %
1
0.04
0.03
0.02
0.01
0.00
–0.01
–0.02
–0.03
–0.04
3rd
RL = 150⍀
G = +2
3rd
RL = 150⍀
–60
0.04
0.03
0.02
0.01
0.00
–0.01
–0.02
–0.03
–0.04
10000
Figure 13. Output Voltage Swing vs. Load
–40
DISTORTION – dBc
+5V
3
150⍀ DIFF PHASE – Degrees
GAIN – dB
6.1
100
Figure 15. Diff Phase and Diff Gain; VS = +5 V
–6–
REV. B
AD8011
+9
+3
+6
0
1V rms
–3
OUTPUT VOLTAGE – dBV
OUTPUT VOLTAGE – dBV
+3
1V rms
0
–3
–6
–9
–12
–6
–9
–12
–15
–18
–15
–21
–18
–24
–27
–21
1
10
40
FREQUENCY – MHz
100
1
500
10
40
FREQUENCY – MHz
100
500
Figure 19. Large Signal Frequency Response;
VS = +5 V, G = +2
Figure 16. Large Signal Frequency Response;
VS = ± 5 V, G = +2
+5
VS = +5V OR ⴞ5V
VOUT = 200mV p-p
NORMALIZED GAIN – dB
+3
G = +1
RF = 1k⍀
OUTPUT VOLTAGE – 0.1%/DIV
+4
+2
G = +2
RF = 1k⍀
+1
0
–1
G = +10
RF = 500⍀
–2
–3
–4
–5
1
10
FREQUENCY – MHz
100
500
t=0
Figure 20. Short-Term Settling Time; VS = +5 V or ± 5 V
Figure 17. Frequency Response; G = +1, +2, +10;
VS = +5 V or ± 5 V
+2
VS = +5V OR ⴞ5V
VOUT = 200mV p-p
G = –10
RF = 500⍀
RL = 1k⍀
NORMALIZED GAIN – dB
0
–1
OUTPUT VOLTAGE – 0.1%/DIV
+1
G = –1
RF = 1k⍀
RL = 1k⍀
–2
–3
–4
–5
–6
–7
–8
1
10
FREQUENCY – MHz
100
500
t=0
Figure 21. Long-Term Settling Time; VS = +5 V or ± 5 V
Figure 18. Frequency Response; G = –1, –10;
VS = +5 V or ± 5 V
REV. B
–7–
AD8011
+10
–10
–20
0
VS = +5V OR ⴞ5V
G = +2
–20
+PSRR
PSRR – dB
CMRR – dB
–25
–30
–35
–40
–40
–50
–60
–50
–70
–55
–80
–90
–60
0.1
1
10
FREQUENCY – MHz
100k
100
Figure 22. CMRR vs. Frequency; VS = +5 V or ± 5 V
1M
10M
FREQUENCY – Hz
100M
500M
Figure 25. PSRR vs. Frequency; VS = +5 V or ± 5 V
VS = +5V OR ⴞ5V
G = +2
RF = 1k⍀
INPUT VOLTAGE NOISE – nV/ Hz
OUTPUT RESISTANCE – ⍀
–30
–45
100
–PSRR
VS = +5V OR ⴞ5V
G = +2
RF = 1k⍀
–10
10
1
0.1
12.5
50
10
40
7.5
30
5
20
2.5
10
INPUT CURRENT NOISE – pA/ Hz
–15
0.01
10k
0.1M
1M
10M
FREQUENCY – Hz
100M
0
500
500M
120
–40
PEAK-TO-PEAK OUTPUT AT 5MHz ( 0.5% THD) – V
0
–80
80
–120
GAIN
60
–160
40
–200
20
–240
0
1k
10k
100k
1M
10M
FREQUENCY – Hz
100M
PHASE – Degrees
GAIN – dB Ohms
PHASE
100
0
100k
10k
FREQUENCY – Hz
Figure 26. Noise vs. Frequency; VS = +5 V or ± 5 V
Figure 23. Output Resistance vs. Frequency; VS = +5 V
or ± 5 V
140
1k
–280
1G
Figure 24. Transimpedance Gain and Phase vs. Frequency
9
RL = 1k⍀
8
f = 5MHz
G = +2
RF = 1k⍀
7
6
RL = 150⍀
5
4
3
2
1
0
3
4
5
6
7
8
9
TOTAL SUPPLY VOLTAGE – V
10
11
Figure 27. Output Swing vs. Supply
–8–
REV. B
AD8011
THEORY OF OPERATION
Overall, when “high” external load drive and low ac distortion is
a requirement, a twin gain stage integrating amplifier like the
AD8011 will provide superior results for lower power over the
traditional single stage complementary devices. In addition,
being a CF amplifier, closed-loop BW variations versus external
gain variations (varying RN) will be much lower compared to a
VF op amp, where the BW varies inversely with gain. Another
key attribute of this amplifier is its ability to run on a single 5 V
supply due in part to its wide common-mode input and output
voltage range capability. For 5 V supply operation, the device
obviously consumes half the quiescent power (vs. 10 V supply)
with little degradation in its ac and dc performance characteristics. See data sheet comparisons.
The AD8011 is a revolutionary generic high-speed CF amplifier
that attains new levels of BW, power, distortion, and signal
swing capability. If these key parameters were combined as a
figure of ac merit performance or [(frequency × VSIG)/(distortion
× power)], no IC amplifier today would come close to the merit
value of the AD8011 for frequencies above a few MHz. Its wide
dynamic performance (including noise) is the result of both a
new complementary high speed bipolar process and a new and
unique architectural design. The AD8011 uses basically a two
gain stage complementary design approach versus the traditional
“single stage” complementary mirror structure sometimes referred to as the Nelson amplifier. Though twin stages have been
tried before, they typically consumed high power since they
were of a folded cascade design much like the AD9617. This
design allows for the standing or quiescent current to add to the
high signal or slew current induced stages much like the Nelson
or single stage design. Thus, in the time domain, the large signal
output rise/fall time and slew rate is controlled typically by the
small signal BW of the amplifier and the input signal step amplitude respectively, not the dc quiescent current of the gain stages
(with the exception of input level shift diodes Q1/Q2). Using
two stages vs. one also allows for a higher overall gain bandwidth product (GBWP) for the same power, thus lower signal
distortion and the ability to drive heavier external loads. In
addition, the second gain stage also isolates (divides down) A3’s
input reflected load drive and the nonlinearities created resulting in relatively lower distortion and higher open-loop gain.
A1
Gain stages A1/A1B and A2/A2B combined provide negative
feedforward transresistance gain. See Figure 28. Stage A3 is a
unity gain buffer which provides external load isolation to A2.
Each stage uses a symmetrical complementary design. (A3 is
also complementary though not explicitly shown). This is done
to both reduce second order signal distortion and overall quiescent power as discussed above. In the quasi dc to low frequency
region, the closed loop gain relationship can be approximated as:
G = 1+RF /RN
G = –RF /RN
noninverting operation
inverting operation
These basic relationships above are common to all traditional
operational amplifiers. Due to the inverting input error current
(IE) required to servo the output and the inverting I E × R I drop
CD
Z1 = R1 || C1
Z1
IPN
IPP
DC GAIN CHARACTERISTICS
–VI
A2
CP1
IQ1
Q3
CP2
IR + IFC
ICQ + IO
Q1
VN
VP
VO
ZI
A3
Z2
VO
RL
Q2
RF
IE
RL
IR – IFC
Q4
ICQ – IO
Z1
IQ1
INP
–VI
IPN
A2
CP1
AD8011
A1
CD
Figure 28. Simplified Block Diagram
REV. B
–9–
CL
AD8011
(error current times the open loop inverting input resistance)
that results (see Figure 29), a more exact low frequency closed
loop transfer functions can be described as:
G
G
=
G × RI RF
R
G
1+
1+
+
+ F
TO
TO
AO T O
for noninverting (G is positive)
AV =
G
1 – G RF
1+
+
TO
AO
AC TRANSFER CHARACTERISTICS
The ac small signal transfer derivations below are based on a
simplified single-pole model. Though inaccurate at frequencies
approaching the closed-loop BW (CLBW) of the AD8011 at low
noninverting external gains, they still provide a fair approximation
and a intuitive understanding of its primary ac small signal
characteristics.
for inverting (G is negative)
+VS
TO (s)
AO (s)
IE
VP
ZI
LI
CP
For inverting operation and high noninverting gains these transfer equations provide a good approximation to the actual ac
performance of the device.
LS
LN
RS
RN
VO
RL
To accurately quantify the VO vs. VP relationship, both AO(s)
and TO(s) need to be derived. This can be seen by the following
nonexpanded noninverting gain relationship:
CL
LS
RF
G
VO (s) /VP (s) =
–VS
G
Z I = OPEN LOOP INPUT IMPEDANCE = CI || RL
AO [s]
Figure 29. ZI = Open-Loop Input Impedance
where G is the ideal gain as previously described. With
R I = TO/AO (open-loop inverting input resistance), the second
expression (positive G) clearly relates to the classical voltage
feedback “op amp” equation with TO omitted do to its relatively
much higher value and thus insignificant effect. AO and TO are
the open-loop dc voltage and transresistance gains of the amplifier respectively. These key transfer variables can be described as:
(1 – g mc × R1)
and TO =
R1 × | A2 |
2
; therefore RI =
1− g
mc
2× g
RF
TO [s]
+1
with
AO(s) =
Sτ1
Where gmc is the positive feedback transconductance (not
shown) and 1/gmf is the thermal emitter resistance of devices
D1/D2 and Q3/Q4. The gmc × R1 product has a design value that
results in a negative dc open loop gain of typically –2500 V/V (see
Figure 30).
80
–90
70
–100
–110
60
× R1
mf
PHASE
50
–120
–130
40
GAIN
30
–140
–150
20
–160
10
AO(s)
0
–170
–10
–180
–20
–190
–30
1E+03
Though atypical of conventional CF or VF amps, this negative
open-loop voltage gain results in an input referred error term
(VP–VO/G = G/AO + RF/TO) that will typically be negative for G
greater than +3/–4. As an example, for G = 10, AO = –2500 and
TO = 1.2 MΩ, results in a error of –3 mV using the AV derivation above.
R1 × gmf ×|A2|
1 – gmc × R1
1 – gmc × R1
GAIN – dB Ohms
AO =
R1 × g mf × | A2 |
+
1E+04
1E+05
1E+06
PHASE – Degrees
AV =
This analysis assumes perfect current sources and infinite transistor VAs (Q3, Q4 output conductances are assumed zero).
These assumptions result in actual vs. model open loop voltage
gain and associated input referred error terms being less accurate
for low gain (G) noninverting operation at the frequencies below
the open loop pole of the AD8011. This is primarily a result of
the input signal (VP) modulating the output conductances of
Q3/Q4 resulting in RI less negative than derived here. For inverting operation, the actual vs. model dc error terms are relatively
much less.
1E+07
1E+08
–200
1E+09
FREQUENCY – Hz
Figure 30. Open-Loop Voltage Gain and Phase
–10–
REV. B
AD8011
where R1 is the input resistance to A2/A2B, and τ1 (equal to
CD × R1 × A2) is the open loop dominate time constant.
SERIES 1
0
120
–40
PHASE
–60
250
–80
ZI(s)
220
–100
190
–120
–140
–120
GAIN
60
–160
TO(s)
40
–200
20
–240
100
1E+03
1E+04
1E+05
1E+06
1E+07
FREQUENCY – Hz
–180
1E+09
1E+08
Figure 32. Open-Loop Inverting Input Impedance
–280
1E+09
Figure 31. Open-Loop Transimpedance Gain
Note that the ac open-loop plots in Figures 31, 32 and 33 are
based on the full Spice AD8011 simulations and do not include
external parasitics (see below). Nevertheless, these ac loop equations still provide a good approximation to simulated and actual
performance up to the CLBW of the amplifier. Typically gmc ×
R1 is –4, resulting in AO(s) having a right half plane pole. In the
time domain (inverse Laplace of AO) it appears as unstable,
causing VO to exponentially rail out of its linear region. When
the loop is closed however, the BW is greatly extended and the
transimpedance gain, TO (s) “overrides” and directly controls
the amplifiers stability behavior due to ZI approaching 1/2 gmf
for s>>1/τ1. See Figure 32. This can be seen by the ZI (s) and
AV (s) noninverting transfer equations below.


Sτ1
(1 – gmc × R1)
+ 1
1
–
g
×
R1


mc
ZI (s) =
2 × gmf (Sτ1 + 1)
–160
130
PHASE – Degrees
GAIN – dB Ohms
80
1E+08
280
SERIES 2
–80
1E+05
1E+06
1E+07
FREQUENCY – Hz
–40
160
100
1E+04
–20
PHASE
310
ZI (s) goes positive real and approaches 1/2 gmf as ω approaches
(gmc × R1 – 1)/τ1. This results in the input resistance for the
AV (s) complex term being 1/2 gmf; the parallel thermal emitter
resistances of Q3/Q4. Using the computed CLBW from AV (s)
above and the nominal design values for the other parameters,
results in a closed loop 3 dB BW equal to the open loop corner
frequency (1/2 πτ1) times 1/[G/(2 gmf × TO) + RF/TO]. For a
fixed RF, the 3 dB BW is controlled by the RF/TO term for low
gains and G/(2 gmf × TO) for high gains. For example, using
nominal design parameters and R1 = 1 kΩ (which results in a
nominal TO of 1.2 MΩ, the computed BW is 80 MHz for G = 0
(inverting I-V mode with RN removed) and 40 MHz for
G = +10/–9.
DRIVING CAPACITIVE LOADS
The AD8011 was designed primarily to drive nonreactive loads.
If driving loads with a capacitive component is desired, best
settling response is obtained by the addition of a small series
resistance as shown in Figure 33. The accompanying graph
shows the optimum value for RSERIES vs. capacitive load. It is
worth noting that the frequency response of the circuit when
driving large capacitive loads will be dominated by the passive
roll-off of RSERIES and CL.
1k⍀
1k⍀
G
AV (s) =
RF  
RF 
G
 G


1 + AO + TO   Sτ1 2 gmf TO + TO  + 1


RSERIES
AD8011
RL
1k⍀
CL
Figure 33. Driving Capacitive Load
REV. B
PHASE – Degrees
140
0
1E+03
0
IMPEDANCE
340
|A2|×R1
2
sτ1+1
RESISTANCE – Ohms
and TO (s) =
20
400
370
–11–
AD8011
40
11
10
VS = ⴞ5V
G = +2
VIN = 200mV
9
8
30
GAIN – dB
RSERIES – ⍀
RF = 750⍀
7
6
RF = 1k⍀
5
20
4
3
2
10
0
5
10
15
20
1
25
1
CL – pF
10
FREQUENCY – MHz
100
500
Figure 35. Flatness vs. Feedback
Figure 34. Recommended RSERIES vs. Capacitive Load for
≤ 30 ns Settling to 0.1%
OPTIMIZING FLATNESS
As mentioned, the ac transfer equations above are based on
a simplified single pole model. Due to the devices internal parasitics (primarily CP1/CP1B and CP2 in Figure 28) and
external package/board parasites (partially represented in Figure
34) the computed BW, using the VO (s) equation above, typically will be lower than the AD8011’s measured small signal
BW. See data sheet Bode plots.
With internal parasitics included only, the BW is extended do to
the complex pole pairs created primarily by CP1/CP2B and CP2
versus the single-pole assumption shown above. This results in a
“design controlled” closed-loop damping factor (ζ) of nominally
0.6 resulting in the CLBW increasing by approximately 1.3×
higher than the computed single pole value above for optimized
external gains of +2/–1! As external noninverting gain (G) is
increased, the actual closed-loop bandwidth vs. the computed
single pole ac response is in closer agreement.
Inverting pin and external component capacitance (designated
CP) will further extend the CLBW do the closed loop zero created by CP and RN储RF when operating in the noninverting mode.
Using proper RF component and layout techniques (see layout
section) this capacitance should be about 1.5 pF. This results in a
further incremental BW increase of almost 2× (versus the computed value) for G = +1 decreasing and approaching its complex
pole pair BW for gains approaching +6 or higher. As previously
discussed, the single-pole response begins to correlate well. Note
that a pole is also created by 1/2 gmf and CP which prevents the
AD8011 from becoming unstable. This parasitic has the greatest
effect on BW and peaking for low positive gains as the data
sheet Bode plots clearly show. For inverting operation, CP has
relatively much less effect on CLBW variation.
Output pin and external component capacitance (designated
CL ) will further extend the devices BW and can also cause peaking below and above the CLBW if too high. In the time domain,
poor step settling characteristics (ringing up to about 2 GHz
and excessive overshoot) can result. For high CL values greater
than about 5 pF an external series “damping” resistor is recommended. See section on Settling Time vs. CL. For light loads,
any output capacitance will reflect back on A2’s output (Z2 of
buffer A3) as both added capacitance near the CLBW (CLBW
> fT/B) and eventually negative resistance at much higher frequencies. These added effects are proportional to the load C.
This reflected capacitance and negative resistance has the effect
of both reducing A2/s phase margin and causing high frequency
“L × C” peaking respectively. Using an external series resistor
(as specified above) reduces these unwanted effects by creating a
reflected zero to A2’s output which will reduce the peaking and
eliminate ringing. For heavy resistive loads, relatively more Load
C would be required to cause these same effects.
High inductive parasitics, especially on the supplies and inverting/
noninverting inputs, can cause modulated low level RF ringing
on the output in the transient domain. Again, proper RF component and board layout practices need to be observed. Relatively
high parasitic lead inductance (roughly L >15 nh) can result in
L × C underdamped ringing. Here L/C means all associated
input pin, external component and leadframe strays including
collector to substrate device capacitance. In the ac domain, this
L × C resonance effect would typically not appear in the passband of the amplifier but would appear in the open loop response at frequencies well above the CLBW of the amplifier.
–12–
REV. B
AD8011
INCREASING BW AT HIGH GAINS
As presented above, for a fixed RF (feedback gain setting resistor) the AD8011 CLBW will decrease as RN is reduced (increased G). This effect can be minimized by simply reducing RF
and thus partially restoring the devices optimized BW for gains
greater than +2/–1. Note that the AD8011 is ac optimized (high
BW and low peaking) for AV =+2/–1 and RF equal to 1 kΩ.
Using this optimized G as a reference and the VO(s) equations
above, the following relationships results:
RF = 1k + 2 – G/2 gm for G = 1+ RF/RN
(noninverting) or:
RF = 1k + G + 1/2 gm for G = –RF/RN
(inverting)
Using 1/2 gm equal to 120 Ω results in a RF of 500 Ω for
G = 5/–4 and a corresponding RN of 125 Ω. This will extend the
AD8011’s BW to near its optimum design value of typically 180
MHz at RL = 1 kΩ. In general, for gains greater than +7/–6, RF
should not be reduced to values much below 400 Ω else ac
peaking can result. Using this RF value as the a lower limit, will
result in BW restoration near its optimized value to the upper G
values specified. Gains greater than about +7/–6 will result
in CLBW reduction. Again, the derivations above are just
approximations.
DRIVING A SINGLE-SUPPLY A/D CONVERTER
New CMOS A/D converters are placing greater demands on the
amplifiers that drive them. Higher resolutions, faster conversion
rates and input switching irregularities require superior settling
characteristics. In addition, these devices run off a single +5 V
supply and consume little power, so good single-supply operation
with low power consumption are very important. The AD8011
is well positioned for driving this new class of A/D converters.
Figure 36 shows a circuit that uses an AD8011 to drive an
AD876, a single supply, 10-bit, 20 MSPS A/D converter that
requires only 140 mW. Using the AD8011 for level shifting and
driving, the A/D exhibits no degradation in performance compared to when it is driven from a signal generator.
When the input is at 1 V, there is 1.2 mA flowing into the summing junction through R3 and 1.2 mA flowing out through R1.
These currents balance and leave no current to flow through
R2. Thus the output is at the same potential as the inverting
input or 1.6 V.
The input of the AD876 has a series MOSFET switch that turns
on and off at the sampling rate. This MOSFET is connected to
a hold capacitor internal to the device. The on impedance of the
MOSFET is about 50 Ω, while the hold capacitor is about 5 pF.
In a worst case condition, the input voltage to the AD876 will
change by a full-scale value (2 V) in one sampling cycle. When
the input MOSFET turns on, the output of the op amp will be
connected to the charged hold capacitor through the series
resistance of the MOSFET. Without any other series resistance,
the instantaneous current that flows would be 40 mA. This
would cause settling problems for the op amp.
The series 100 Ω resistor limits the current that flows instantaneously after the MOSFET turns on to about 13 mA. This
resistor cannot be made too large or the high frequency performance will be affected.
The sampling MOSFET of the AD876 is closed for only half of
each cycle or for 25 ns. Approximately 7 time constants are
required for settling to 10 bits. The series 100 Ω resistor along
with the 50 Ω on resistance and the hold capacitor, create a
750 ps time constant. These values leave a comfortable margin
for settling. Obtaining the same results with the op amp A/D
combination as compared to driving with a signal generator
indicates that the op amp is settling fast enough.
Overall the AD8011 provides adequate buffering for the AD876
A/D converter without introducing distortion greater than that
of the A/D converter by itself.
+5V
R3
1.65k⍀
0.1␮F
10␮F
3.6V
0.1␮F
The analog input of the AD876 spans 2 V centered at about
2.6 V. The resistor network and bias voltages provide the level
shifting and gain required to convert the 0 V to 1 V input signal
to a 3.6 V to 1.6 V range that the AD876 wants to see.
1V
0V
Biasing the noninverting input of the AD8011 at 1.6 V dc forces
the inverting input to be at 1.6 V dc for linear operation of the
amplifier. When the input is at 0 V, there is 3.2 mA flowing out
of the summing junction via R1 (1.6 V/499 Ω). R3 has a current
of 1.2 mA flowing into the summing junction (3.6 V–1.6 V)/
1.65 kΩ. The difference of these two currents (2 mA) must flow
through R2. This current flows toward the summing junction
and requires that the output be 2 V higher than the summing
junction or at 3.6 V.
REV. B
R2
1k⍀
–13–
+3.6V
R1
499k⍀
VIN
50⍀
0.1␮F
REFT
100⍀
AD8011
AD876
3.6V
1.6V
REFB
+1.6V
1.6V
Figure 36. AD8011 Driving the AD876
AD8011
LAYOUT CONSIDERATIONS
RF
RG
VIN
The specified high speed performance of the AD8011 requires
careful attention to board layout and component selection.
Table I shows the recommended component values for the
AD8011 and Figures 38–40 show the layout for the AD8011
evaluation board (8-lead SOIC, Gain = +2). Proper RF design
techniques and low parasitic component selection are mandatory.
RO
VOUT
RT
The PCB should have a ground plane covering all unused portions of the component side of the board to provide a low impedance ground path. The ground plane should be removed
from the area near the input pins to reduce stray capacitance.
C1
0.01␮F
C3
10␮F
C2
0.01␮F
C4
10␮F
–VS
INVERTING CONFIGURATION
RF
RG
Chip capacitors should be used for supply bypassing (see Figure 37). One end should be connected to the ground plane
and the other within 1/8 in. of each power pin. An additional
(4.7 µF–10 µF) tantalum electrolytic capacitor should be connected in parallel.
RO
VOUT
VIN
RT
+VS
C1
0.01␮F
C3
10␮F
C2
0.01␮F
C4
10␮F
+VS
–VS
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance greater than 1.5 pF at the inverting
input will significantly affect high speed performance when
operating at low noninverting gains.
NONINVERTING CONFIGURATION
Figure 37. Inverting and Noninverting Configurations
Stripline design techniques should be used for long signal traces
(greater than about 1 in.). These should be designed with the
proper system characteristic impedance and be properly terminated at each end.
Table I. Typical Bandwidth vs. Gain Setting Resistors
Gain
RF (⍀)
RG (⍀)
RT (⍀)
–1
–2
–10
+1
+2
+10
+6
+6
1000
1000
499
1000
1000
422
1000
500
1000
499
49.9
52.3
54.9
49.9
49.9
49.9
49.9
49.9
1000
47.5
200
100
Small Signal –3 dB BW
(MHz), VS = ⴞ5 V
150
130
140
400
250
100
70
170
RT chosen for 50 Ω characteristic input impedance.
RO chosen for characteristic output impedance.
–14–
REV. B
AD8011
Figure 38. Evaluation Board Silkscreen (Top)
Figure 39. Evaluation Board Layout (Solder Side)
Figure 40. Evaluation Board Layout (Component Side)
REV. B
–15–
AD8011
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Plastic DIP
(N-8)
8
C01048a–0–7/00 (rev. B)
0.430 (10.92)
0.348 (8.84)
5
0.280 (7.11)
0.240 (6.10)
1
4
0.325 (8.25)
0.300 (7.62)
PIN 1
0.100 (2.54)
BSC
0.210
(5.33)
MAX
0.060 (1.52)
0.015 (0.38)
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558) 0.070 (1.77) SEATING
0.014 (0.356) 0.045 (1.15) PLANE
0.015 (0.381)
0.008 (0.204)
8-Lead Plastic SOIC
(SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.1574 (4.00)
0.1497 (3.80)
8
5
1
4
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.0196 (0.50)
ⴛ 45ⴗ
0.0099 (0.25)
0.0500 (1.27)
BSC
SEATING
PLANE
0.0688 (1.75)
0.0532 (1.35)
0.0192 (0.49)
0.0138 (0.35)
8ⴗ
0.0500 (1.27)
0.0098 (0.25) 0ⴗ
0.0160 (0.41)
0.0075 (0.19)
PRINTED IN U.S.A.
0.0098 (0.25)
0.0040 (0.10)
–16–
REV. B